commit 0294112ee3 upstream.
This effectively reverts the following three commits:
7bc10388cc ACPI / resources: free memory on error in add_region_before()
0f1b414d19 ACPI / PNP: Avoid conflicting resource reservations
b9a5e5e18f ACPI / init: Fix the ordering of acpi_reserve_resources()
(commit b9a5e5e18f introduced regressions some of which, but not
all, were addressed by commit 0f1b414d19 and commit 7bc10388cc
was a fixup on top of the latter) and causes ACPI fixed hardware
resources to be reserved at the fs_initcall_sync stage of system
initialization.
The story is as follows. First, a boot regression was reported due
to an apparent resource reservation ordering change after a commit
that shouldn't lead to such changes. Investigation led to the
conclusion that the problem happened because acpi_reserve_resources()
was executed at the device_initcall() stage of system initialization
which wasn't strictly ordered with respect to driver initialization
(and with respect to the initialization of the pcieport driver in
particular), so a random change causing the device initcalls to be
run in a different order might break things.
The response to that was to attempt to run acpi_reserve_resources()
as soon as we knew that ACPI would be in use (commit b9a5e5e18f).
However, that turned out to be too early, because it caused resource
reservations made by the PNP system driver to fail on at least one
system and that failure was addressed by commit 0f1b414d19.
That fix still turned out to be insufficient, though, because
calling acpi_reserve_resources() before the fs_initcall stage of
system initialization caused a boot regression to happen on the
eCAFE EC-800-H20G/S netbook. That meant that we only could call
acpi_reserve_resources() at the fs_initcall initialization stage
or later, but then we might just as well call it after the PNP
initalization in which case commit 0f1b414d19 wouldn't be
necessary any more.
For this reason, the changes made by commit 0f1b414d19 are reverted
(along with a memory leak fixup on top of that commit), the changes
made by commit b9a5e5e18f that went too far are reverted too and
acpi_reserve_resources() is changed into fs_initcall_sync, which
will cause it to be executed after the PNP subsystem initialization
(which is an fs_initcall) and before device initcalls (including
the pcieport driver initialization) which should avoid the initial
issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100581
Link: http://marc.info/?t=143092384600002&r=1&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e18f "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 0f1b414d19 upstream.
Commit b9a5e5e18f "ACPI / init: Fix the ordering of
acpi_reserve_resources()" overlooked the fact that the memory
and/or I/O regions reserved by acpi_reserve_resources() may
conflict with those reserved by the PNP "system" driver.
If that conflict actually takes place, it causes the reservations
made by the "system" driver to fail while before commit b9a5e5e18f
all reservations made by it and by acpi_reserve_resources() would be
successful. In turn, that allows the resources that haven't been
reserved by the "system" driver to be used by others (e.g. PCI) which
sometimes leads to functional problems (up to and including boot
failures).
To fix that issue, introduce a common resource reservation routine,
acpi_reserve_region(), to be used by both acpi_reserve_resources()
and the "system" driver, that will track all resources reserved by
it and avoid making conflicting requests.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e18f "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 90db10434b upstream.
No caller currently checks the return value of
kvm_io_bus_unregister_dev(). This is evil, as all callers silently go on
freeing their device. A stale reference will remain in the io_bus,
getting at least used again, when the iobus gets teared down on
kvm_destroy_vm() - leading to use after free errors.
There is nothing the callers could do, except retrying over and over
again.
So let's simply remove the bus altogether, print an error and make
sure no one can access this broken bus again (returning -ENOMEM on any
attempt to access it).
Fixes: e93f8a0f82 ("KVM: convert io_bus to SRCU")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 3243367b20 upstream.
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit d1b4c689d4 upstream.
mmapped netlink has a number of unresolved issues:
- TX zerocopy support had to be disabled more than a year ago via
commit 4682a03586 ("netlink: Always copy on mmap TX.")
because the content of the mmapped area can change after netlink
attribute validation but before message processing.
- RX support was implemented mainly to speed up nfqueue dumping packet
payload to userspace. However, since commit ae08ce0021
("netfilter: nfnetlink_queue: zero copy support") we avoid one copy
with the socket-based interface too (via the skb_zerocopy helper).
The other problem is that skbs attached to mmaped netlink socket
behave different from normal skbs:
- they don't have a shinfo area, so all functions that use skb_shinfo()
(e.g. skb_clone) cannot be used.
- reserving headroom prevents userspace from seeing the content as
it expects message to start at skb->head.
See for instance
commit aa3a022094 ("netlink: not trim skb for mmaped socket when dump").
- skbs handed e.g. to netlink_ack must have non-NULL skb->sk, else we
crash because it needs the sk to check if a tx ring is attached.
Also not obvious, leads to non-intuitive bug fixes such as 7c7bdf359
("netfilter: nfnetlink: use original skbuff when acking batches").
mmaped netlink also didn't play nicely with the skb_zerocopy helper
used by nfqueue and openvswitch. Daniel Borkmann fixed this via
commit 6bb0fef489 ("netlink, mmap: fix edge-case leakages in nf queue
zero-copy")' but at the cost of also needing to provide remaining
length to the allocation function.
nfqueue also has problems when used with mmaped rx netlink:
- mmaped netlink doesn't allow use of nfqueue batch verdict messages.
Problem is that in the mmap case, the allocation time also determines
the ordering in which the frame will be seen by userspace (A
allocating before B means that A is located in earlier ring slot,
but this also means that B might get a lower sequence number then A
since seqno is decided later. To fix this we would need to extend the
spinlocked region to also cover the allocation and message setup which
isn't desirable.
- nfqueue can now be configured to queue large (GSO) skbs to userspace.
Queing GSO packets is faster than having to force a software segmentation
in the kernel, so this is a desirable option. However, with a mmap based
ring one has to use 64kb per ring slot element, else mmap has to fall back
to the socket path (NL_MMAP_STATUS_COPY) for all large packets.
To use the mmap interface, userspace not only has to probe for mmap netlink
support, it also has to implement a recv/socket receive path in order to
handle messages that exceed the size of an rx ring element.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ken-ichirou MATSUZAWA <chamaken@gmail.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 474c90156c upstream.
gcc-7 has an "optimization" pass that completely screws up, and
generates the code expansion for the (impossible) case of calling
ilog2() with a zero constant, even when the code gcc compiles does not
actually have a zero constant.
And we try to generate a compile-time error for anybody doing ilog2() on
a constant where that doesn't make sense (be it zero or negative). So
now gcc7 will fail the build due to our sanity checking, because it
created that constant-zero case that didn't actually exist in the source
code.
There's a whole long discussion on the kernel mailing about how to work
around this gcc bug. The gcc people themselevs have discussed their
"feature" in
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=72785
but it's all water under the bridge, because while it looked at one
point like it would be solved by the time gcc7 was released, that was
not to be.
So now we have to deal with this compiler braindamage.
And the only simple approach seems to be to just delete the code that
tries to warn about bad uses of ilog2().
So now "ilog2()" will just return 0 not just for the value 1, but for
any non-positive value too.
It's not like I can recall anybody having ever actually tried to use
this function on any invalid value, but maybe the sanity check just
meant that such code never made it out in public.
[js] no tools/include/linux/log2.h copy of that yet
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>,
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit 745cb7f8a5 ]
Replace MAX_ADDR_LEN with its numeric value to fix the following
linux/packet_diag.h userspace compilation error:
/usr/include/linux/packet_diag.h:67:17: error: 'MAX_ADDR_LEN' undeclared here (not in a function)
__u8 pdmc_addr[MAX_ADDR_LEN];
This is not the first case in the UAPI where the numeric value
of MAX_ADDR_LEN is used instead of symbolic one, uapi/linux/if_link.h
already does the same:
$ grep MAX_ADDR_LEN include/uapi/linux/if_link.h
__u8 mac[32]; /* MAX_ADDR_LEN */
There are no UAPI headers besides these two that use MAX_ADDR_LEN.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Pavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit e33886b38c upstream.
Add two helpers to make it easier to treat the refcount as boolean.
[js] do not involve WARN_ON_ONCE as it causes build failures
Suggested-by: Jason Baron <jasonbaron0@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit bf7165cfa2 upstream.
There are several trace include files that define TRACE_INCLUDE_FILE.
Include several of them in the same .c file (as I currently have in
some code I am working on), and the compile will blow up with a
"warning: "TRACE_INCLUDE_FILE" redefined #define TRACE_INCLUDE_FILE syscalls"
Every other include file in include/trace/events/ avoids that issue
by having a #undef TRACE_INCLUDE_FILE before the #define; syscalls.h
should have one, too.
Link: http://lkml.kernel.org/r/20160928225554.13bd7ac6@annuminas.surriel.com
Fixes: b8007ef742 ("tracing: Separate raw syscall from syscall tracer")
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 251af29c32 upstream.
It is not sufficient to just check that the lock pids match when
granting a callback, we also need to ensure that we're granting
the callback on the right file.
Reported-by: Pankaj Singh <psingh.ait@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 55efcfcd77 upstream.
The RDMA core uses ib_pack() to convert from unpacked CPU structs
to on-the-wire bitpacked structs.
This process requires that 1 bit fields are declared as u8 in the
unpacked struct, otherwise the packing process does not read the
value properly and the packed result is wired to 0. Several
places wrongly used int.
Crucially this means the kernel has never, set reversible
correctly in the path record request. It has always asked for
irreversible paths even if the ULP requests otherwise.
When the kernel is used with a SM that supports this feature, it
completely breaks communication management if reversible paths are
not properly requested.
The only reason this ever worked is because opensm ignores the
reversible bit.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 11ffff752c upstream.
In commit 1ec047eb47 ("ipv6: introduce per-interface counter for
dad-completed ipv6 addresses") I build the detection of the first
operational link-local address much to complex. Additionally this code
now has a race condition.
Replace it with a much simpler variant, which just scans the address
list when duplicate address detection completes, to check if this is
the first valid link local address and send RS and MLD reports then.
Fixes: 1ec047eb47 ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses")
Reported-by: Jiri Pirko <jiri@resnulli.us>
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit 8b74d439e1 ]
It seems nobody used LLC since linux-3.12.
Fortunately fuzzers like syzkaller still know how to run this code,
otherwise it would be no fun.
Setting skb->sk without skb->destructor leads to all kinds of
bugs, we now prefer to be very strict about it.
Ideally here we would use skb_set_owner() but this helper does not exist yet,
only CAN seems to have a private helper for that.
[js] take sock_efree from 62bccb8cdb
Fixes: 376c7311bd ("net: add a temporary sanity check in skb_orphan()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit d71b789688 ]
syzkaller found another out of bound access in ip_options_compile(),
or more exactly in cipso_v4_validate()
Fixes: 20e2a86485 ("cipso: handle CIPSO options correctly when NetLabel is disabled")
Fixes: 446fda4f26 ("[NetLabel]: CIPSOv4 engine")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit f1712c7371 ]
Zhang Yanmin reported crashes [1] and provided a patch adding a
synchronize_rcu() call in can_rx_unregister()
The main problem seems that the sockets themselves are not RCU
protected.
If CAN uses RCU for delivery, then sockets should be freed only after
one RCU grace period.
Recent kernels could use sock_set_flag(sk, SOCK_RCU_FREE), but let's
ease stable backports with the following fix instead.
[1]
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81495e25>] selinux_socket_sock_rcv_skb+0x65/0x2a0
Call Trace:
<IRQ>
[<ffffffff81485d8c>] security_sock_rcv_skb+0x4c/0x60
[<ffffffff81d55771>] sk_filter+0x41/0x210
[<ffffffff81d12913>] sock_queue_rcv_skb+0x53/0x3a0
[<ffffffff81f0a2b3>] raw_rcv+0x2a3/0x3c0
[<ffffffff81f06eab>] can_rcv_filter+0x12b/0x370
[<ffffffff81f07af9>] can_receive+0xd9/0x120
[<ffffffff81f07beb>] can_rcv+0xab/0x100
[<ffffffff81d362ac>] __netif_receive_skb_core+0xd8c/0x11f0
[<ffffffff81d36734>] __netif_receive_skb+0x24/0xb0
[<ffffffff81d37f67>] process_backlog+0x127/0x280
[<ffffffff81d36f7b>] net_rx_action+0x33b/0x4f0
[<ffffffff810c88d4>] __do_softirq+0x184/0x440
[<ffffffff81f9e86c>] do_softirq_own_stack+0x1c/0x30
<EOI>
[<ffffffff810c76fb>] do_softirq.part.18+0x3b/0x40
[<ffffffff810c8bed>] do_softirq+0x1d/0x20
[<ffffffff81d30085>] netif_rx_ni+0xe5/0x110
[<ffffffff8199cc87>] slcan_receive_buf+0x507/0x520
[<ffffffff8167ef7c>] flush_to_ldisc+0x21c/0x230
[<ffffffff810e3baf>] process_one_work+0x24f/0x670
[<ffffffff810e44ed>] worker_thread+0x9d/0x6f0
[<ffffffff810e4450>] ? rescuer_thread+0x480/0x480
[<ffffffff810ebafc>] kthread+0x12c/0x150
[<ffffffff81f9ccef>] ret_from_fork+0x3f/0x70
Reported-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 059aa73482 upstream.
Xuan Qi reports that the Linux NFSv4 client failed to lock a file
that was migrated. The steps he observed on the wire:
1. The client sent a LOCK request to the source server
2. The source server replied NFS4ERR_MOVED
3. The client switched to the destination server
4. The client sent the same LOCK request to the destination
server with a bumped lock sequence ID
5. The destination server rejected the LOCK request with
NFS4ERR_BAD_SEQID
RFC 3530 section 8.1.5 provides a list of NFS errors which do not
bump a lock sequence ID.
However, RFC 3530 is now obsoleted by RFC 7530. In RFC 7530 section
9.1.7, this list has been updated by the addition of NFS4ERR_MOVED.
Reported-by: Xuan Qi <xuan.qi@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 073931017b upstream.
When file permissions are modified via chmod(2) and the user is not in
the owning group or capable of CAP_FSETID, the setgid bit is cleared in
inode_change_ok(). Setting a POSIX ACL via setxattr(2) sets the file
permissions as well as the new ACL, but doesn't clear the setgid bit in
a similar way; this allows to bypass the check in chmod(2). Fix that.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit b6416e6101 upstream.
Modules that use static_key_deferred need a way to synchronize with
any delayed work that is still pending when the module is unloaded.
Introduce static_key_deferred_flush() which flushes any pending
jump label updates.
[js] no STATIC_KEY_CHECK_USE in 3.12 -> remove it
Signed-off-by: David Matlack <dmatlack@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit 57ea52a865 ]
The GRO fast path caches the frag0 address. This address becomes
invalid if frag0 is modified by pskb_may_pull or its variants.
So whenever that happens we must disable the frag0 optimization.
This is usually done through the combination of gro_header_hard
and gro_header_slow, however, the IPv6 extension header path did
the pulling directly and would continue to use the GRO fast path
incorrectly.
This patch fixes it by disabling the fast path when we enter the
IPv6 extension header path.
Fixes: 78a478d0ef ("gro: Inline skb_gro_header and cache frag0 virtual address")
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 0335695dfa upstream.
The current_user_ns() macro currently returns &init_user_ns when user
namespaces are disabled, and that causes several warnings when building
with gcc-6.0 in code that compares the result of the macro to
&init_user_ns itself:
fs/xfs/xfs_ioctl.c: In function 'xfs_ioctl_setattr_check_projid':
fs/xfs/xfs_ioctl.c:1249:22: error: self-comparison always evaluates to true [-Werror=tautological-compare]
if (current_user_ns() == &init_user_ns)
This is a legitimate warning in principle, but here it isn't really
helpful, so I'm reprasing the definition in a way that shuts up the
warning. Apparently gcc only warns when comparing identical literals,
but it can figure out that the result of an inline function can be
identical to a constant expression in order to optimize a condition yet
not warn about the fact that the condition is known at compile time.
This is exactly what we want here, and it looks reasonable because we
generally prefer inline functions over macros anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 777c6e0dae upstream.
Yu Zhao has noticed that __unregister_cpu_notifier only unregisters its
notifiers when HOTPLUG_CPU=y while the registration might succeed even
when HOTPLUG_CPU=n if MODULE is enabled. This means that e.g. zswap
might keep a stale notifier on the list on the manual clean up during
the pool tear down and thus corrupt the list. Resulting in the following
[ 144.964346] BUG: unable to handle kernel paging request at ffff880658a2be78
[ 144.971337] IP: [<ffffffffa290b00b>] raw_notifier_chain_register+0x1b/0x40
<snipped>
[ 145.122628] Call Trace:
[ 145.125086] [<ffffffffa28e5cf8>] __register_cpu_notifier+0x18/0x20
[ 145.131350] [<ffffffffa2a5dd73>] zswap_pool_create+0x273/0x400
[ 145.137268] [<ffffffffa2a5e0fc>] __zswap_param_set+0x1fc/0x300
[ 145.143188] [<ffffffffa2944c1d>] ? trace_hardirqs_on+0xd/0x10
[ 145.149018] [<ffffffffa2908798>] ? kernel_param_lock+0x28/0x30
[ 145.154940] [<ffffffffa2a3e8cf>] ? __might_fault+0x4f/0xa0
[ 145.160511] [<ffffffffa2a5e237>] zswap_compressor_param_set+0x17/0x20
[ 145.167035] [<ffffffffa2908d3c>] param_attr_store+0x5c/0xb0
[ 145.172694] [<ffffffffa290848d>] module_attr_store+0x1d/0x30
[ 145.178443] [<ffffffffa2b2b41f>] sysfs_kf_write+0x4f/0x70
[ 145.183925] [<ffffffffa2b2a5b9>] kernfs_fop_write+0x149/0x180
[ 145.189761] [<ffffffffa2a99248>] __vfs_write+0x18/0x40
[ 145.194982] [<ffffffffa2a9a412>] vfs_write+0xb2/0x1a0
[ 145.200122] [<ffffffffa2a9a732>] SyS_write+0x52/0xa0
[ 145.205177] [<ffffffffa2ff4d97>] entry_SYSCALL_64_fastpath+0x12/0x17
This can be even triggered manually by changing
/sys/module/zswap/parameters/compressor multiple times.
Fix this issue by making unregister APIs symmetric to the register so
there are no surprises.
[js] backport to 3.12
Fixes: 47e627bc8c ("[PATCH] hotplug: Allow modules to use the cpu hotplug notifiers even if !CONFIG_HOTPLUG_CPU")
Reported-and-tested-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: linux-mm@kvack.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Link: http://lkml.kernel.org/r/20161207135438.4310-1-mhocko@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 332b05ca7a upstream.
This patch adds a check to limit the number of can_filters that can be
set via setsockopt on CAN_RAW sockets. Otherwise allocations > MAX_ORDER
are not prevented resulting in a warning.
Reference: https://lkml.org/lkml/2016/12/2/230
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit e784930bd6 upstream.
Export pcie_find_root_port() so we can use it outside of PCIe-AER error
injection.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 6b2a3d628a upstream.
The data to audit/record is in the 'from' buffer (ie., the input
read buffer).
Fixes: 72586c6061 ("n_tty: Fix auditing support for cannonical mode")
Cc: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit c3c87e7704 upstream.
The fix from 9fc81d8742 ("perf: Fix events installation during
moving group") was incomplete in that it failed to recognise that
creating a group with events for different CPUs is semantically
broken -- they cannot be co-scheduled.
Furthermore, it leads to real breakage where, when we create an event
for CPU Y and then migrate it to form a group on CPU X, the code gets
confused where the counter is programmed -- triggered in practice
as well by me via the perf fuzzer.
Fix this by tightening the rules for creating groups. Only allow
grouping of counters that can be co-scheduled in the same context.
This means for the same task and/or the same cpu.
Fixes: 9fc81d8742 ("perf: Fix events installation during moving group")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20150123125834.090683288@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit ac6e780070 ]
With syzkaller help, Marco Grassi found a bug in TCP stack,
crashing in tcp_collapse()
Root cause is that sk_filter() can truncate the incoming skb,
but TCP stack was not really expecting this to happen.
It probably was expecting a simple DROP or ACCEPT behavior.
We first need to make sure no part of TCP header could be removed.
Then we need to adjust TCP_SKB_CB(skb)->end_seq
Many thanks to syzkaller team and Marco for giving us a reproducer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Marco Grassi <marco.gra@gmail.com>
Reported-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit 23f4ffedb7 ]
skb->cb may contain data from previous layers. In the observed scenario,
the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so
that small packets sent through the tunnel are mistakenly fragmented.
This patch unconditionally clears the control buffer in ip6tunnel_xmit(),
which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of
these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 8c7fbe5795 upstream.
Commit 3876488444 ("include/stddef.h: Move offsetofend() from vfio.h
to a generic kernel header") added offsetofend outside the normal
include #ifndef/#endif guard. Move it inside.
Miscellanea:
o remove unnecessary blank line
o standardize offsetof macros whitespace style
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit b13460b920 upstream.
The macro offsetofend() introduces unnecessary temporary variable
"tmp". The patch avoids that and saves a bit memory in stack.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit 20c64d5cd5 ]
A malicious TCP receiver, sending SACK, can force the sender to split
skbs in write queue and increase its memory usage.
Then, when socket is closed and its write queue purged, we might
overflow sk_forward_alloc (It becomes negative)
sk_mem_reclaim() does nothing in this case, and more than 2GB
are leaked from TCP perspective (tcp_memory_allocated is not changed)
Then warnings trigger from inet_sock_destruct() and
sk_stream_kill_queues() seeing a not zero sk_forward_alloc
All TCP stack can be stuck because TCP is under memory pressure.
A simple fix is to preemptively reclaim from sk_mem_uncharge().
This makes sure a socket wont have more than 2 MB forward allocated,
after burst and idle period.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 1a24e04e4b upstream.
sk_mem_reclaim_partial() goal is to ensure each socket has
one SK_MEM_QUANTUM forward allocation. This is needed both for
performance and better handling of memory pressure situations in
follow up patches.
SK_MEM_QUANTUM is currently a page, but might be reduced to 4096 bytes
as some arches have 64KB pages.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 2531c8cf56 upstream.
s390 has a constant hugepage size, by setting HPAGE_SHIFT we also change
e.g. the pageblock_order, which should be independent in respect to
hugepage support.
With this patch every architecture is free to define how to check
for hugepage support.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 0733424c9b upstream.
Exported pwm channels aren't removed before the pwmchip and are
leaked. This results in invalid sysfs files. This fix removes
all exported pwm channels before chip removal.
Signed-off-by: David Hsu <davidhsu@google.com>
Fixes: 76abbdde2d ("pwm: Add sysfs interface")
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit a09a4c8dd1 upstream.
If a packet is either locally encapsulated or processed through GRO
it is marked with the offloads that it requires. However, when it is
decapsulated these tunnel offload indications are not removed. This
means that if we receive an encapsulated TCP packet, aggregate it with
GRO, decapsulate, and retransmit the resulting frame on a NIC that does
not support encapsulation, we won't be able to take advantage of hardware
offloads even though it is just a simple TCP packet at this point.
This fixes the problem by stripping off encapsulation offload indications
when packets are decapsulated.
The performance impacts of this bug are significant. In a test where a
Geneve encapsulated TCP stream is sent to a hypervisor, GRO'ed, decapsulated,
and bridged to a VM performance is improved by 60% (5Gbps->8Gbps) as a
result of avoiding unnecessary segmentation at the VM tap interface.
[js] no fou in 3.12 yet
Reported-by: Ramu Ramamurthy <sramamur@linux.vnet.ibm.com>
Fixes: 68c33163 ("v4 GRE: Add TCP segmentation offload for GRE")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
(backported from commit a09a4c8dd1)
[adapt iptunnel_pull_header arguments, avoid 7f290c9]
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Juerg Haefliger <juerg.haefliger@hpe.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
part of commit f6eec614d2 upstream.
Add NETIF_F_GSO_ENCAP_ALL mask covering all encapsulation GSO flags.
[mk] only introduce the helper, do not pick the openvswitch change the
original commit was about.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 5864a2fd30 upstream.
Commit 6d07b68ce1 ("ipc/sem.c: optimize sem_lock()") introduced a
race:
sem_lock has a fast path that allows parallel simple operations.
There are two reasons why a simple operation cannot run in parallel:
- a non-simple operations is ongoing (sma->sem_perm.lock held)
- a complex operation is sleeping (sma->complex_count != 0)
As both facts are stored independently, a thread can bypass the current
checks by sleeping in the right positions. See below for more details
(or kernel bugzilla 105651).
The patch fixes that by creating one variable (complex_mode)
that tracks both reasons why parallel operations are not possible.
The patch also updates stale documentation regarding the locking.
With regards to stable kernels:
The patch is required for all kernels that include the
commit 6d07b68ce1 ("ipc/sem.c: optimize sem_lock()") (3.10?)
The alternative is to revert the patch that introduced the race.
The patch is safe for backporting, i.e. it makes no assumptions
about memory barriers in spin_unlock_wait().
Background:
Here is the race of the current implementation:
Thread A: (simple op)
- does the first "sma->complex_count == 0" test
Thread B: (complex op)
- does sem_lock(): This includes an array scan. But the scan can't
find Thread A, because Thread A does not own sem->lock yet.
- the thread does the operation, increases complex_count,
drops sem_lock, sleeps
Thread A:
- spin_lock(&sem->lock), spin_is_locked(sma->sem_perm.lock)
- sleeps before the complex_count test
Thread C: (complex op)
- does sem_lock (no array scan, complex_count==1)
- wakes up Thread B.
- decrements complex_count
Thread A:
- does the complex_count test
Bug:
Now both thread A and thread C operate on the same array, without
any synchronization.
[js] use set_mb instead of smp_store_mb
Fixes: 6d07b68ce1 ("ipc/sem.c: optimize sem_lock()")
Link: http://lkml.kernel.org/r/1469123695-5661-1-git-send-email-manfred@colorfullife.com
Reported-by: <felixh@informatik.uni-bremen.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <1vier1@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 536fa40222 upstream.
CPUs without single-byte and double-byte loads and stores place some
"interesting" requirements on concurrent code. For example (adapted
from Peter Hurley's test code), suppose we have the following structure:
struct foo {
spinlock_t lock1;
spinlock_t lock2;
char a; /* Protected by lock1. */
char b; /* Protected by lock2. */
};
struct foo *foop;
Of course, it is common (and good) practice to place data protected
by different locks in separate cache lines. However, if the locks are
rarely acquired (for example, only in rare error cases), and there are
a great many instances of the data structure, then memory footprint can
trump false-sharing concerns, so that it can be better to place them in
the same cache cache line as above.
But if the CPU does not support single-byte loads and stores, a store
to foop->a will do a non-atomic read-modify-write operation on foop->b,
which will come as a nasty surprise to someone holding foop->lock2. So we
now require CPUs to support single-byte and double-byte loads and stores.
Therefore, this commit adjusts the definition of __native_word() to allow
these sizes to be used by smp_load_acquire() and smp_store_release().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 19be0eaffa upstream.
This is an ancient bug that was actually attempted to be fixed once
(badly) by me eleven years ago in commit 4ceb5db975 ("Fix
get_user_pages() race for write access") but that was then undone due to
problems on s390 by commit f33ea7f404 ("fix get_user_pages bug").
In the meantime, the s390 situation has long been fixed, and we can now
fix it by checking the pte_dirty() bit properly (and do it better). The
s390 dirty bit was implemented in abf09bed3c ("s390/mm: implement
software dirty bits") which made it into v3.9. Earlier kernels will
have to look at the page state itself.
Also, the VM has become more scalable, and what used a purely
theoretical race back then has become easier to trigger.
To fix it, we introduce a new internal FOLL_COW flag to mark the "yes,
we already did a COW" rather than play racy games with FOLL_WRITE that
is very fundamental, and then use the pte dirty flag to validate that
the FOLL_COW flag is still valid.
Reported-and-tested-by: Phil "not Paul" Oester <kernel@linuxace.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Michal Hocko <mhocko@suse.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Nick Piggin <npiggin@gmail.com>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 9a6dc64451 upstream.
set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug. It's done
consistently so it won't cause a problem unless "irq" is more than 4.
Fixes: 70c6cce040 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 9abefcb1aa upstream.
A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].
To resolve this issue, the restart_timer is replaced by a delayed
work.
[1] https://github.com/victronenergy/venus/issues/24
Signed-off-by: Sergei Miroshnichenko <sergeimir@emcraft.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit e23d4159b1 upstream.
Switching iov_iter fault-in to multipages variants has exposed an old
bug in underlying fault_in_multipages_...(); they break if the range
passed to them wraps around. Normally access_ok() done by callers will
prevent such (and it's a guaranteed EFAULT - ERR_PTR() values fall into
such a range and they should not point to any valid objects).
However, on architectures where userland and kernel live in different
MMU contexts (e.g. s390) access_ok() is a no-op and on those a range
with a wraparound can reach fault_in_multipages_...().
Since any wraparound means EFAULT there, the fix is trivial - turn
those
while (uaddr <= end)
...
into
if (unlikely(uaddr > end))
return -EFAULT;
do
...
while (uaddr <= end);
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 2545e5da08 upstream.
... in all cases, including the failing access_ok()
Note that some architectures using asm-generic/uaccess.h have
__copy_from_user() not zeroing the tail on failure halfway
through. This variant works either way.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 9ad18b75c2 upstream.
both for access_ok() failures and for faults halfway through
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit 24b27fc4cd ]
Following few steps will crash kernel -
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ Upstream commit bb1fceca22 ]
When tcp_sendmsg() allocates a fresh and empty skb, it puts it at the
tail of the write queue using tcp_add_write_queue_tail()
Then it attempts to copy user data into this fresh skb.
If the copy fails, we undo the work and remove the fresh skb.
Unfortunately, this undo lacks the change done to tp->highest_sack and
we can leave a dangling pointer (to a freed skb)
Later, tcp_xmit_retransmit_queue() can dereference this pointer and
access freed memory. For regular kernels where memory is not unmapped,
this might cause SACK bugs because tcp_highest_sack_seq() is buggy,
returning garbage instead of tp->snd_nxt, but with various debug
features like CONFIG_DEBUG_PAGEALLOC, this can crash the kernel.
This bug was found by Marco Grassi thanks to syzkaller.
Fixes: 6859d49475 ("[TCP]: Abstract tp->highest_sack accessing & point to next skb")
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 4097461897 upstream.
As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we
have a hard load dependency between i8042 and atkbd which prevents
keyboard from working on Gen2 Hyper-V VMs.
> hyperv_keyboard invokes serio_interrupt(), which needs a valid serio
> driver like atkbd.c. atkbd.c depends on libps2.c because it invokes
> ps2_command(). libps2.c depends on i8042.c because it invokes
> i8042_check_port_owner(). As a result, hyperv_keyboard actually
> depends on i8042.c.
>
> For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a
> Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m
> rather than =y, atkbd.ko can't load because i8042.ko can't load(due to
> no i8042 device emulated) and finally hyperv_keyboard can't work and
> the user can't input: https://bugs.archlinux.org/task/39820
> (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y)
To break the dependency we move away from using i8042_check_port_owner()
and instead allow serio port owner specify a mutex that clients should use
to serialize PS/2 command stream.
Reported-by: Mark Laws <mdl@60hz.org>
Tested-by: Mark Laws <mdl@60hz.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a1b2725a6 upstream.
Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.
[js] backport to 3.12: no use_new_scheme yet
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
