-----BEGIN PGP SIGNATURE-----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=zdH0
-----END PGP SIGNATURE-----
Merge tag 'v6.6.34' into lf-6.6.y
This is the 6.6.34 stable release
* tag 'v6.6.34': (2530 commits)
Linux 6.6.34
smp: Provide 'setup_max_cpus' definition on UP too
selftests: net: more strict check in net_helper
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
drivers/net/ethernet/freescale/fec_ptp.c
drivers/pmdomain/imx/imx8mp-blk-ctrl.c
drivers/usb/dwc3/host.c
tools/perf/util/pmu.c
[ Upstream commit bce3f77068 ]
When processing a SYSERR, if the device does not respond to the MHI_RESET
from the host, the host will be stuck in a difficult to recover state.
The host will remain in MHI_PM_SYS_ERR_PROCESS and not clean up the host
channels. Clients will not be notified of the SYSERR via the destruction
of their channel devices, which means clients may think that the device is
still up. Subsequent SYSERR events such as a device fatal error will not
be processed as the state machine cannot transition from PROCESS back to
DETECT. The only way to recover from this is to unload the mhi module
(wipe the state machine state) or for the mhi controller to initiate
SHUTDOWN.
This issue was discovered by stress testing soc_reset events on AIC100
via the sysfs node.
soc_reset is processed entirely in hardware. When the register write
hits the endpoint hardware, it causes the soc to reset without firmware
involvement. In stress testing, there is a rare race where soc_reset N
will cause the soc to reset and PBL to signal SYSERR (fatal error). If
soc_reset N+1 is triggered before PBL can process the MHI_RESET from the
host, then the soc will reset again, and re-run PBL from the beginning.
This will cause PBL to lose all state. PBL will be waiting for the host
to respond to the new syserr, but host will be stuck expecting the
previous MHI_RESET to be processed.
Additionally, the AMSS EE firmware (QSM) was hacked to synthetically
reproduce the issue by simulating a FW hang after the QSM issued a
SYSERR. In this case, soc_reset would not recover the device.
For this failure case, to recover the device, we need a state similar to
PROCESS, but can transition to DETECT. There is not a viable existing
state to use. POR has the needed transitions, but assumes the device is
in a good state and could allow the host to attempt to use the device.
Allowing PROCESS to transition to DETECT invites the possibility of
parallel SYSERR processing which could get the host and device out of
sync.
Thus, invent a new state - MHI_PM_SYS_ERR_FAIL
This essentially a holding state. It allows us to clean up the host
elements that are based on the old state of the device (channels), but
does not allow us to directly advance back to an operational state. It
does allow the detection and processing of another SYSERR which may
recover the device, or allows the controller to do a clean shutdown.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240112180800.536733-1-quic_jhugo@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27711860c5 ]
There is a copy and paste bug here so it checks "ev_ring_el_cache" instead
of "ring_item_cache".
Fixes: 62210a26cd ("bus: mhi: ep: Use slab allocator where applicable")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/bebcd822-d465-45da-adae-5435ec93e6d4@moroto.mountain
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4acd21a45c ]
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just Tegra210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes Tegra210 you don't get
this driver.
Fixes: 46a88534af ("bus: Add support for Tegra ACONNECT")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bca405c98 ]
When the range parsing was open-coded the number of u32 entries to
parse had to be a multiple of 4 and the driver checks this. With
the range parsing converted to the range parser the counting changes
from individual u32 entries to a complete range, so the check must
not reject counts not divisible by 4.
Fixes: 2a88e4792c ("bus: imx-weim: Remove open coded "ranges" parsing")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b89b6a863d upstream.
Protect WP accesses such that multiple threads queueing buffers for
incoming data do not race.
Meanwhile, if CONFIG_TRACE_IRQFLAGS is enabled, irq will be enabled once
__local_bh_enable_ip is called as part of write_unlock_bh. Hence, let's
take irqsave lock after TRE is generated to avoid running write_unlock_bh
when irqsave lock is held.
Cc: stable@vger.kernel.org
Fixes: 189ff97cca ("bus: mhi: core: Add support for data transfer")
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Tested-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1702276972-41296-2-git-send-email-quic_qianyu@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bd694ac2 upstream.
Ensure read and write locks for the channel are not taken in succession by
dropping the read lock from parse_xfer_event() such that a callback given
to client can potentially queue buffers and acquire the write lock in that
process. Any queueing of buffers should be done without channel read lock
acquired as it can result in multiple locks and a soft lockup.
Cc: <stable@vger.kernel.org> # 5.7
Fixes: 1d3173a3ba ("bus: mhi: core: Add support for processing events from client device")
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Tested-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1702276972-41296-3-git-send-email-quic_qianyu@quicinc.com
[mani: added fixes tag and cc'ed stable]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eff9704f53 upstream.
Though we do check the event ring read pointer by "is_valid_ring_ptr"
to make sure it is in the buffer range, but there is another risk the
pointer may be not aligned. Since we are expecting event ring elements
are 128 bits(struct mhi_ring_element) aligned, an unaligned read pointer
could lead to multiple issues like DoS or ring buffer memory corruption.
So add a alignment check for event ring read pointer.
Fixes: ec32332df7 ("bus: mhi: core: Sanity check values from remote device before use")
cc: stable@vger.kernel.org
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231031-alignment_check-v2-1-1441db7c5efd@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b08ded2ef2 ]
In the preparation of DMA async support, let's pass the parameters to
read_from_host() and write_to_host() APIs using mhi_ep_buf_info structure.
No functional change.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: 327ec5f706 ("PCI: epf-mhi: Fix the DMA data direction of dma_unmap_single()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62210a26cd ]
Use slab allocator for allocating the memory for objects used frequently
and are of fixed size. This reduces the overheard associated with
kmalloc().
Suggested-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20231018122812.47261-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: 327ec5f706 ("PCI: epf-mhi: Fix the DMA data direction of dma_unmap_single()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 987fdb5a43 ]
It is possible that the host controller driver would use DMA framework to
write the event ring element. So avoid allocating event ring element on the
stack as DMA cannot work on vmalloc memory.
Cc: stable@vger.kernel.org
Fixes: 961aeb6892 ("bus: mhi: ep: Add support for sending events to the host")
Link: https://lore.kernel.org/r/20230901073502.69385-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: 327ec5f706 ("PCI: epf-mhi: Fix the DMA data direction of dma_unmap_single()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aaafe88d55 upstream.
The moxtet module fails to auto-load on. Add a SPI id table to
allow it to do so.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7830f5a83 upstream.
The Turris Mox shares the moxtet IRQ with various devices on the board,
so mark the IRQ as shared in the driver as well.
Without this loading the module will fail with:
genirq: Flags mismatch irq 40. 00002002 (moxtet) vs. 00002080 (mcp7940x)
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Cc: <stable@vger.kernel.org> # v6.2+
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f71f6ff8c1 upstream.
Commit 34539b442b ("bus: ti-sysc: Flush posted write on enable before
reset") caused a regression reproducable on omap4 duovero where the ISS
target module can produce interconnect errors on boot. Turns out the
registers are not accessible until after a delay for devices needing
a ti,sysc-delay-us value.
Let's fix this by flushing the posted write only after the reset delay.
We do flushing also for ti,sysc-delay-us using devices as that should
trigger an interconnect error if the delay is not properly configured.
Let's also add some comments while at it.
Fixes: 34539b442b ("bus: ti-sysc: Flush posted write on enable before reset")
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The blamed commit tried to simplify how the deallocations are done but,
in the process, introduced a double-free on the mc_dev variable.
In case the MC device is a DPRC, a new mc_bus is allocated and the
mc_dev variable is just a reference to one of its fields. In this
circumstance, on the error path only the mc_bus should be freed.
This commit introduces back the following checkpatch warning which is a
false-positive.
WARNING: kfree(NULL) is safe and this check is probably not required
+ if (mc_bus)
+ kfree(mc_bus);
Fixes: a042fbed02 ("staging: fsl-mc: simplify couple of deallocations")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
This function will be shared with the DPRC .remove() op in the
following patch so lets not leak the irq data on that path.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
When devices are owned by VFIO lets not allow user-space to play with
them through the restool management interface thus breaking isolation.
Drop restool misc device creation and destruction from the common
dprc_setup() and dprc_cleanup() functions (shared with fsl-mc VFIO)
and open code it dprc driver's probe and remove ops.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
In VFIO case, the irq array in the fsl_mc device is not initialized,
so given that in upcoming patches this code will also get called by
VFIO add a check for null in the irq teardown function.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
This cleanup is actually a no-op because the resources are freed when
the device objects are removed from the allocator at driver remove
time.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
With recent MC release, a timeout of 500ms is not enough in most
circumstances. If MC firmware will respond faster, we should
decrease this value.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
This reverts commit 98e96cf800.
The following commit introduced in v5.15-rc6 breaks i.MX8QM/QXP
suspend/resume. The issue was reported in community [1] and still under
discussion and not conclusion on the proper fix so far.
This patch temporarily revert it in order to make the release work.
i.MX seems not use .sync_state() mentioned in the original commit,
suppose it may be safe as we also havn't used it before.
98e96cf800 ("drivers: bus: simple-pm-bus: Add support for probing simple bus only devices")
1. https://lore.kernel.org/all/YYu4EglV7SBZU2Iy@ryzen/
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of
SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE
is used to force idle target modules rather than block idle during usage.
The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when
a target module is active, and configure autoidle and wake-up when a
target module is inactive. We are missing configuring the target module
on sysc_disable_module(), and missing toggling of the wake-up bit.
Let's fix the issue to allow uart wake-up to work.
Fixes: fb685f1c19 ("bus: ti-sysc: Handle swsup idle mode quirks")
Tested-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
created a list of SoC types searching for strings based on names
and wildcards which associates the SoC to different families.
The OMAP34xx and OMAP35xx are treated as SOC_3430 while
OMAP36xx and OMAP37xx are treated as SOC_3630, but the AM35xx
isn't listed.
The AM35xx is mostly an OMAP3430, and a later commit a12315d6d2
("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific") looks
for the SOC type and behaves in a certain way if it's SOC_3430.
This caused a regression on the AM3517 causing it to return two
errors:
ti-sysc: probe of 48318000.target-module failed with error -16
ti-sysc: probe of 49032000.target-module failed with error -16
Fix this by treating the creating SOC_AM35 and inserting it between
the SOC_3430 and SOC_3630. If it is treaed the same way as the
SOC_3430 when checking the status of sysc_check_active_timer,
the error conditions will disappear.
Fixes: a12315d6d2 ("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific")
Fixes: feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-ID: <20230906233442.270835-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am335x-evm started producing boot errors because of subtle timing
changes:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf03c1010
...
sysc_reset from sysc_probe+0xf60/0x1514
sysc_probe from platform_probe+0x5c/0xbc
...
The fix consists in using the appropriate sleep function in sysc reset.
For flexible sleeping, fsleep is recommended. Here, sysc delay parameter
can take any value in [0 - 255] us range. As a result, fsleep() should
be used, calling udelay() for a sysc delay lower than 10 us.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Fixes: e709ed70d1 ("bus: ti-sysc: Fix missing reset delay handling")
Message-ID: <20230821-fix-ti-sysc-reset-v1-1-5a0a5d8fae55@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH64g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynr2QCfd3RKeR+WnGzyEOFhksl30UJJhiIAoNZtYT5+
t9KG0iMDXRuTsOqeEQbd
=tVnk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (267 commits)
nvmem: core: Notify when a new layout is registered
nvmem: core: Do not open-code existing functions
nvmem: core: Return NULL when no nvmem layout is found
nvmem: core: Create all cells before adding the nvmem device
nvmem: u-boot-env:: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
nvmem: sec-qfprom: Add Qualcomm secure QFPROM support
dt-bindings: nvmem: sec-qfprom: Add bindings for secure qfprom
dt-bindings: nvmem: Add compatible for QCM2290
nvmem: Kconfig: Fix typo "drive" -> "driver"
nvmem: Explicitly include correct DT includes
nvmem: add new NXP QorIQ eFuse driver
dt-bindings: nvmem: Add t1023-sfp efuse support
dt-bindings: nvmem: qfprom: Add compatible for MSM8226
nvmem: uniphier: Use devm_platform_get_and_ioremap_resource()
nvmem: qfprom: do some cleanup
nvmem: stm32-romem: Use devm_platform_get_and_ioremap_resource()
nvmem: rockchip-efuse: Use devm_platform_get_and_ioremap_resource()
nvmem: meson-mx-efuse: Convert to devm_platform_ioremap_resource()
nvmem: lpc18xx_otp: Convert to devm_platform_ioremap_resource()
nvmem: brcm_nvram: Use devm_platform_get_and_ioremap_resource()
...
These are all minor cleanups for platform specific code in arch/arm/
and some of the associated drivers. The majority of these are work
done by Rob Herring to improve the way devicetreee header files
are handled.
-----BEGIN PGP SIGNATURE-----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=c9NM
-----END PGP SIGNATURE-----
Merge tag 'soc-arm-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These are all minor cleanups for platform specific code in arch/arm/
and some of the associated drivers. The majority of these are work
done by Rob Herring to improve the way devicetreee header files are
handled"
* tag 'soc-arm-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (49 commits)
ARM: davinci: Drop unused includes
ARM: s5pv210: Explicitly include correct DT includes
ARM: dove: Drop unused includes
ARM: mvebu: Explicitly include correct DT includes
Documentation/process: maintainer-soc: document dtbs_check requirement for Samsung
MAINTAINER: samsung: document dtbs_check requirement for Samsung
Documentation/process: maintainer-soc: add clean platforms profile
MAINTAINERS: soc: reference maintainer profile
ARM: nspire: Remove unused header file mmio.h
ARM: nspire: Use syscon-reboot to handle restart
soc: fsl: Explicitly include correct DT includes
soc: xilinx: Explicitly include correct DT includes
soc: sunxi: Explicitly include correct DT includes
soc: rockchip: Explicitly include correct DT includes
soc: mediatek: Explicitly include correct DT includes
soc: aspeed: Explicitly include correct DT includes
firmware: Explicitly include correct DT includes
bus: Explicitly include correct DT includes
ARM: spear: Explicitly include correct DT includes
ARM: mvebu: Explicitly include correct DT includes
...
The main change this time is the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together. Ulf Hansson is taking over maintainership for
these and is sending a separate pull request with the same commits,
but they are in the soc drivers tree to avoid conflicts against other
soc driver patches.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other firmware
drivers.
On the soc driver side, the updates are mostly cleanups across a number
of Arm platforms. On driver for loongarch adds power management for DT
based systems, another driver is for HiSilicon's Arm server chips with
their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform.
-----BEGIN PGP SIGNATURE-----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=xmHW
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main change this time was the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other
firmware drivers.
On the soc driver side, the updates are mostly cleanups across a
number of Arm platforms. On driver for loongarch adds power management
for DT based systems, another driver is for HiSilicon's Arm server
chips with their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform"
* tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (136 commits)
bus: fsl-mc: Use common ranges functions
soc: kunpeng_hccs: fix some sparse warnings about incorrect type
soc: loongson2_pm: add power management support
soc: dt-bindings: add loongson-2 pm
soc: rockchip: grf: Fix SDMMC not working on RK3588 with bus-width > 1
genpd: rockchip: Add PD_VO entry for rv1126
bus: ti-sysc: Fix cast to enum warning
soc: kunpeng_hccs: add MAILBOX dependency
MAINTAINERS: remove OXNAS entry
dt-bindings: interrupt-controller: arm,versatile-fpga-irq: mark oxnas compatible as deprecated
irqchip: irq-versatile-fpga: remove obsolete oxnas compatible
soc: qcom: aoss: Tidy up qmp_send() callers
soc: qcom: aoss: Format string in qmp_send()
soc: qcom: aoss: Move length requirements from caller
soc: kunpeng_hccs: fix size_t format string
soc: ti: k3-socinfo.c: Add JTAG ID for AM62PX
dt-bindings: firmware: qcom: scm: Updating VMID list
firmware: imx: scu-irq: support identifying SCU wakeup source from sysfs
firmware: imx: scu-irq: enlarge the IMX_SC_IRQ_NUM_GROUP
firmware: imx: scu-irq: add imx_scu_irq_get_status
...
Since commit 3d5089c426 ("of/address: Add support for 3 address cell
bus"), the DT address functions can handle translating buses with 3
address cells. Replace the custom code with the for_each_of_range()
iterator.
The original code had fallbacks to get "#address-cells"/"#size-cells"
from the bus parent node if they are missing. This is non-standard
behavior, and AFAICT the upstream .dts files never relied on that.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230823190958.2717267-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Driver changes for ti-sysc interconnect target module driver and for
l3 interconnect error handler. The ti-sysc driver changes just enable
using it for 64-bit systems like TI am62 that have wake-up capability
for the wkup domain devices. The l3 error handling improves the code
to show the error source if an unrecoverable timeout error occurs.
-----BEGIN PGP SIGNATURE-----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=//Xy
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmTkDGcACgkQYKtH/8kJ
UifhxBAAzjHmDaL0JgVuAi0l9W9W8CYUnZre4S6qAu6349oEaRdpzChE6KWxCCvd
xDginfnU93vXuxvsvTRauW9E63jLQ8vh6XyTpHV+yhbJj8x+NlkK6smp0cGCqClE
cC0w/lg6HrJpkbxcK/PgSlAAFbyCmdsW5T/g+UC5Ip5Ts1pBn8xbdGBMAtzu7Clp
oxqxC6RDDObeUJ5/kUI9ryIG0cH8CtSnrvz0eDLckCt1mhO6Ofw1URxzyTUc79jc
rX69r9v1nPHU++5XuPXAPWc5nWXvwfKJAOXxyHIHO3kMUsEPum+Dd04vTRTD7SzS
j1oiNVqEWocd7DLh8CTNx73hwJyxfjDLv9U2avg5lts6TG5eloAyf/CzCxEC29jo
TSQn8W6yw4rueemzoNUypIKH5t1lkvpkbGZhIiEQf7iBCOx3b7pRJZAkWOniC/Xj
Uw/w1aICfxPPXAfsxGpMC8hIZLhu8aS+He+4tUghWD1HFfxshnSYOcKpw2Cqp8P2
aTgEVTLUzaEw086S/fSKM6+fsT9Fl5vMjH5KxMmRP9k7jhu96SuHX8UV0zKVvYom
U0IvQ2E8rtgoB2zQ3MeaNh0bmyA6PZL3QDpNg4ymWVkvITh6RXFpjXB8XIQh4unA
ivXP4YSJnPFOM4cXlSYykx5nysOKvHkgy3OjfBMSMcqdCMP2avI=
=QAxs
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v6.6/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into soc/drivers
Driver changes for omaps for v6.6
Driver changes for ti-sysc interconnect target module driver and for
l3 interconnect error handler. The ti-sysc driver changes just enable
using it for 64-bit systems like TI am62 that have wake-up capability
for the wkup domain devices. The l3 error handling improves the code
to show the error source if an unrecoverable timeout error occurs.
* tag 'omap-for-v6.6/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix cast to enum warning
bus: ti-sysc: Fix a build warning with W=1 for sysconfig
bus: ti-sysc: Configure uart quirks for k3 SoC
bus: ti-sysc: Build driver for TI K3 SoCs
bus: ti-sysc: Fix build warning for 64-bit build
bus: omap_l3_smx: identify timeout cause before rebooting
Link: https://lore.kernel.org/r/pull-1692158857-597450@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series from NXP i.MX developers (Peng Fan, etc.) to update imx-scu
and imx-scu-irq firmware drivers.
- Add dedicated lockdep class for nested genpd locks to fix a lockdep
warning in imx93-blk-ctrl driver.
- A change from Rob to explicitly include correct DT headers for i.MX
SoC drivers.
- Use devm_platform_ioremap_resource() in imx-weim bus driver.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmTYNCAUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7x+wgAsB65MMhY74a8pjuO0q1nJierjc46
of2ayxR8I1jXQK/3IUijBZpg+8bnQkhXiVK1uyzvLmUc28iw1y6B2dWec/hXRld8
mc516IWjGa0Re+dOeliKPFNWzj6TZRi3TmqKIfg5XIb0poBtxBiXm7tvjm1oYRQl
ijkCqauOXJmK3yMMTQqxknGQG+B8wQDTPnbssk0A46ShD4RrYXmC3wjTEb27WoGk
nw18XT5XpS+LomctRcqza3Bcdry6YPmI0hOt9Oy9db2sBtXbz+bf9tLGKztvfxGz
44R0+Rz/XncJHwRXGgUNR71ps0+WP55qKsqoTw/zHhkS2BPl8gMxhBtQbQ==
=T2Uo
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=2iHc
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/drivers
i.MX drivers update for 6.6:
- A series from NXP i.MX developers (Peng Fan, etc.) to update imx-scu
and imx-scu-irq firmware drivers.
- Add dedicated lockdep class for nested genpd locks to fix a lockdep
warning in imx93-blk-ctrl driver.
- A change from Rob to explicitly include correct DT headers for i.MX
SoC drivers.
- Use devm_platform_ioremap_resource() in imx-weim bus driver.
* tag 'imx-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
firmware: imx: scu-irq: support identifying SCU wakeup source from sysfs
firmware: imx: scu-irq: enlarge the IMX_SC_IRQ_NUM_GROUP
firmware: imx: scu-irq: add imx_scu_irq_get_status
firmware: imx: scu-irq: fix RCU complaint after M4 partition reset
firmware: imx: scu: use EOPNOTSUPP
firmware: imx: scu: use soc name for soc_id
firmware: imx: scu: increase RPC timeout
firmware: imx: scu: change init level to subsys_initcall_sync
soc: imx: Explicitly include correct DT includes
bus: imx-weim: use devm_platform_ioremap_resource
soc: imx: imx93-blk-ctrl: Add dedicated lockdep class for nested genpd locks
Link: https://lore.kernel.org/r/20230813133354.847010-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Couple of minor updates: Code simplification in the vexpress config bus
driver with the use of devm_platform_ioremap_resource() and simplification
of Arm Vexpress platform and related drivers entries in MAINTAINERS file.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEunHlEgbzHrJD3ZPhAEG6vDF+4pgFAmTM1OQACgkQAEG6vDF+
4pg8IBAAzLxEVqsNc+uR12rQSIHU19pO3bsWgPpSgZ0lph6ilnNkCra1LPotjWSP
RNfW/AFJ8z8KRXeZzAq06lNoiGcZ/iusiScRNfIumjnNgcKM3bOV+TdBI6XT7BXA
HWlL3cKkX2RVQ4TXB6DgSnhdfogPq1GkUI9mdU3wwWo6bvq8+zVeLYbhJzXeW7UR
IByhE/53io8o22IodtkDGVc56nDVioFJxvdE8BW0pSiD6Qxcj02maBRHioGMWstM
bs63kIcf4hmzNLGO1TuO0zCUZsXKc2dbyKZ2czrB0hhgSGx1Nh+Y4OBjrrfDZkcp
Jb/ICpVzdFhhz0rmxj1sgoD3VTvb+iNZ2dA7tsZFtPXZc6fHyW9bJycfLQKDTN7C
dd5zCJPco+qKvGEaSuxg/mFMc7ZyvWVAaPo75RSr3UafSscdV7re+4x6CQZAWwwo
L2C3MMkGJ62LjXfc58Hs9TxS4cBTw8JM8DHlGzjxMMxDwVVpkcD/Oq42Bp6+QHp8
xF68qCmO0WXPKYqWW7vlT81P74QOtSwlqfhuX14Z8RR4uN+FBFKyNqWFq7aRMsgj
Rq5XJTDUUcf5q1w4g43WEYE3XH4FlzriuxMOz8uvnkjw9DnVukZa9ZVUeQ+oYPho
H7nGJmimBJ0gildthj3c7vxZy+VmotgmNn9FfPyIW7X01oTyiKY=
=gL1v
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=B1eB
-----END PGP SIGNATURE-----
Merge tag 'vexpress-updates-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into soc/drivers
Arm Vexpress updates for v6.6
Couple of minor updates: Code simplification in the vexpress config bus
driver with the use of devm_platform_ioremap_resource() and simplification
of Arm Vexpress platform and related drivers entries in MAINTAINERS file.
* tag 'vexpress-updates-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
MAINTAINERS: Simplify entries for Arm Vexpress platform and related drivers
bus: vexpress-config: Convert to devm_platform_ioremap_resource()
Link: https://lore.kernel.org/r/20230804123214.3258032-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-16-d8de2cc88bff@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for Telit FE990 that has the same configuration as FN990:
$ lspci -vv
04:00.0 Unassigned class [ff00]: Qualcomm Device 0308
Subsystem: Device 1c5d:2015
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20230804094039.365102-1-dnlplm@gmail.com
[mani: minor update to commit subject and adjusted comment]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Clang warns about a parameter that is decremented but never evaluated here:
bus/mhi/host/main.c:803:13: error: parameter 'event_quota' set but not used [-Werror,-Wunused-but-set-parameter]
u32 event_quota)
Remove the access to the variable to avoid that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20230811134547.3231160-1-arnd@kernel.org
[mani: minor spelling fix to commit message]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Dhruva reported a build warning with W=1 for "Function parameter or member
'sysconfig' not described in 'sysc'". Let's document sysconfig to fix this.
Reported-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the uart quirks similar to the earlier SoCs. Let's assume we are
likely going to need a k3 specific quirk mask separate from the earlier
SoCs, so let's not start changing the revision register mask at this point.
Note that SYSC_QUIRK_LEGACY_IDLE will be needed until we can remove the
need for pm_runtime_irq_safe() from 8250_omap driver.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow building ti-sysc also for K3 SoCs. This allows configuring the wkup
domain devices for SYSCONFIG register wake-up events in a generic way.
As this is an interconnect level driver, default to built-in on K3 SoCs
to probe the devices connected to the wkup domain like gpio, uart and
timers.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "warning: cast from pointer to integer of different size" on 64-bit
builds.
Note that this is a cosmetic fix at this point as the driver is not yet
used for 64-bit systems.
Fixes: feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Identify and print the error source before rebooting the board due to an l3
timeout error. This is helpful when debugging, e.g. via serial.
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Message-ID: <20230801192240.1063764-1-absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Quectel's RM520N-GL Lenovo variant is same as that of the existing
RM520N-GL modem and uses the same config. But this one is designed for
Lenovo laptop usecase, hence Quectel got a new PID.
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20230807030454.37255-1-duke_xinanwen@163.com
[mani: tweaked subject and commit message a bit]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
