[ Upstream commit 3b23118bdb ]
According to Figure 52A.1 ("RS-CANFD Module Block Diagram (in classical
CAN mode)") in the R-Car V3U Series User’s Manual Rev. 0.5, the parent
clock for the CANFD peripheral module clock is the S3D2 clock.
Fixes: 9b621b6adf ("clk: renesas: r8a779a0: Add CANFD module clock")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/aef9300f44c9141b1465343f91c5cc7303249b6e.1713279523.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1b32a83a0 ]
According to the R-Car S4 Series Hardware User’s Manual Rev.0.81, the
parent clock of the Pin Function (PFC/GPIO) module clock is the CP
clock.
As this clock is not documented to exist on R-Car S4, use the CPEX clock
instead.
Fixes: 73421f2a48 ("clk: renesas: r8a779f0: Add PFC clock")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f88ec4aede0eaf0107c8bb7b28ba719ac6cd418f.1706197415.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abb3fa662b ]
According to the R-Car V4H Series Hardware User’s Manual Rev.1.00, the
parent clock of the Pin Function (PFC/GPIO) module clocks is the CP
clock.
Fix this by adding the missing CP clock, and correcting the PFC parents.
Fixes: f2afa78d5a ("dt-bindings: clock: Add r8a779g0 CPG Core Clock Definitions")
Fixes: 36ff366033 ("clk: renesas: r8a779g0: Add PFC/GPIO clocks")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/5401fccd204dc90b44f0013e7f53b9eff8df8214.1706197297.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da235d2fac ]
The hardware manual of both RZ/G2L and RZ/G3S specifies that the reset
monitor registers need to be interrogated when the reset signals are
toggled (chapters "Procedures for Supplying and Stopping Reset Signals"
and "Procedure for Activating Modules"). Without this, there is a
chance that different modules (e.g. Ethernet) are not ready after their
reset signal is toggled, leading to failures (on probe or resume from
deep sleep states).
The same indications are available for RZ/V2M for TYPE-B reset controls.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Fixes: 8090bea324 ("clk: renesas: rzg2l: Add support for RZ/V2M reset monitor reg")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f9e29b915 ]
Code in rzg2l_cpg_reset() is equivalent with the combined code of
rzg2l_cpg_assert() and rzg2l_cpg_deassert(). There is no need to have
different versions thus re-use rzg2l_cpg_assert() and rzg2l_cpg_deassert().
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231120070024.4079344-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Stable-dep-of: da235d2fac ("clk: renesas: rzg2l: Check reset monitor registers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2b2315949 ]
According to the hardware manual for RZ/G2L
(r01uh0914ej0130-rzg2l-rzg2lc.pdf), the computation formula for PLL rate
is as follows:
Fout = ((m + k/65536) * Fin) / (p * 2^s)
and k has values in the range [-32768, 32767]. Dividing k by 65536 with
integer arithmetic gives zero all the time, causing slight differences
b/w what has been set vs. what is displayed. Thus, get rid of this and
decompose the formula before dividing k by 65536.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-6-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf51d3b2d0 ]
The onitial value of the CPG_PL2SDHI_DSEL bits 0..1 or 4..6 is 01b. The
hardware user's manual (r01uh0914ej0130-rzg2l-rzg2lc.pdf) specifies that
setting 0 is prohibited. Hence rzg2l_cpg_sd_clk_mux_get_parent() should
just read CPG_PL2SDHI_DSEL, trust the value, and return the proper clock
parent index based on the value read.
Fixes: eaff33646f ("clk: renesas: rzg2l: Add SDHI clk mux support")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-5-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2692ed490 ]
The SD MUX output (SD0) is further divided by 4 in G2{L,UL}. The
divided clock is SD0_DIV4. SD0_DIV4 is registered with
CLK_SET_RATE_PARENT which means a rate request for it is propagated to
the MUX and could reach rzg2l_cpg_sd_clk_mux_set_parent() concurrently
with the users of SD0.
Add proper locking to avoid concurrent accesses on SD MUX set rate
registers.
Fixes: eaff33646f ("clk: renesas: rzg2l: Add SDHI clk mux support")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-4-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5252d9697 ]
The clock dividers might be used with clock stop bit enabled or not.
Current tables only support recommended values from the datasheet. This
might result in warnings like below because no valid clock divider is
found. Resulting in a 0 divider.
There are Renesas ARM Trusted Firmware version out there which e.g.
configure 0x201 (shifted logical right by 2: 0x80) and with this match
the added { STPnHCK | 0, 1 }:
https://github.com/renesas-rcar/arm-trusted-firmware/blob/rcar_gen3_v2.3/drivers/renesas/rcar/emmc/emmc_init.c#L108
------------[ cut here ]------------
sd1h: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not set
WARNING: CPU: 1 PID: 1 at drivers/clk/clk-divider.c:141 divider_recalc_rate+0x48/0x70
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.1.52 #1
Hardware name: Custom board based on r8a7796 (DT)
pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : divider_recalc_rate+0x48/0x70
...
------------[ cut here ]------------
Fixes: bb6d3fa98a ("clk: renesas: rcar-gen3: Switch to new SD clock handling")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
[wsa: extended the table to 5 entries, added comments, reword commit message a little]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230928080317.28224-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> # samsung
Acked-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # versaclock5
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143156.1066339-1-robh@kernel.org
Acked-by: Abel Vesa <abel.vesa@linaro.org> #imx
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Renesas RZ/V2M SoC comes with 6 CSI IPs (CSI0, CSI1, CSI2
CSI3, CSI4, and CSI5), however Linux is only allowed control
of CSI0 and CSI4.
CSI0 shares its reset and PCLK lines with CSI1, CSI2, and CSI3.
CSI4 shares its reset and PCLK lines with CSI5.
This commit adds support for the relevant clocks.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230622113341.657842-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The 3DGE and ZG clocks are necessary to support the 3D graphics.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230617150302.38477-4-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The 3DGE and ZG clocks are necessary to support the 3D graphics.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230617150302.38477-3-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The 3DGE and ZG clocks are necessary to support the 3D graphics.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230617150302.38477-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
A clock used for the 3D graphics appears to be common
among multiple SoC's, so add a generic gen3 clock
for clocking the graphics. This is similar to the
cpg_z_clk, with a different frequency control register
and different flags. Instead of duplicating the code,
make cpg_z_clk_register into a helper function and
call the help function with the FCR and flags as
a parameter.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230617150302.38477-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas r9a06g032 bitselect clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidates to
trigger that parent change are either the assigned-clock-parents device
tree property or a call to clk_set_rate(), with determine_rate()
figuring out which parent is the best suited for a given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
Similarly, it doesn't look like the device tree using that clock driver
uses any of the assigned-clock properties on that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the determine_rate
implementation to clk_hw_determine_rate_no_reparent(). Indeed, if no
determine_rate implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-31-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As per the RZ/G2L HW(Rev.1.30 May2023) manual, there are no "write enable"
bits in the CPG_SIPLL5_CLK1 register. So fix the CPG_SIPLL5_CLK register
write by removing the "write enable" bits.
Fixes: 1561380ee7 ("clk: renesas: rzg2l: Add FOUTPOSTDIV clk support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230518152334.514922-1-biju.das.jz@bp.renesas.com
[geert: Remove CPG_SIPLL5_CLK1_*_WEN bit definitions]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
are a couple patches to the core clk framework, but they're all basically
cleanups or debugging aids. The driver updates and new additions are dominated
in the diffstat by Qualcomm and MediaTek drivers. Qualcomm gained a handful of
new drivers for various SoCs, and MediaTek gained a bunch of drivers for
MT8188. The MediaTek drivers are being modernized as well, so there are
updates all over that vendor's clk drivers. There's also a couple other new clk
drivers in here, for example the Starfive JH7110 SoC support is added.
Outside of the two major SoC vendors though, we have the usual collection of
non-critical fixes and cleanups to various clk drivers. It's good to see that
we're getting more cleanups and modernization patches. Maybe one day we'll be
able to properly split clk providers from clk consumers.
Core:
- Print an informational message before disabling unused clks
New Drivers:
- BCM63268 timer clock and reset controller
- Frequency Hopping (FHCTL) on MediaTek MT6795, MT8173, MT8192 and
MT8195 SoCs
- Mediatek MT8188 SoC clk drivers
- Clock driver for Sunplus SP7021 SoC
- Clk driver support for Loongson-2 SoCs
- Clock driver for Skyworks Si521xx I2C PCIe clock generators
- Initial Starfive JH7110 clk/reset support
- Global clock controller drivers for Qualcomm SM7150, IPQ9574, MSM8917 and IPQ5332 SoCs
- GPU clock controller drivers for SM6115, SM6125, SM6375 and SA8775P SoCs
Updates:
- Shrink size of clk_fractional_divider a little
- Convert various clk drivers to devm_of_clk_add_hw_provider()
- Convert platform clk drivers to remove_new()
- Converted most Mediatek clock drivers to struct platform_driver
- MediaTek clock drivers can be built as modules
- Reimplement Loongson-1 clk driver with DT support
- Migrate socfpga clk driver to of_clk_add_hw_provider()
- Support for i3c clks on Aspeed ast2600 SoCs
- Add clock generic devm_clk_hw_register_gate_parent_data
- Add audiomix block control for i.MX8MP
- Add support for determine_rate to i.MX composite-8m
- Let the LCDIF Pixel clock of i.MX8MM and i.MX8MN set parent rate
- Provide clock name in error message for clk-gpr-mux on get parent failure
- Drop duplicate imx_clk_mux_flags macro
- Register the i.MX8MP Media Disp2 Pix clock as bus clock
- Add Media LDB root clock to i.MX8MP
- Make i.MX8MP nand_usdhc_bus clock as non-critical
- Fix the rate table for i.MX fracn-gppll
- Disable HW control for the fracn-gppll in order to be controlled by
register write
- Add support for interger PLL in fracn-gppll
- Add mcore_booted module parameter to i.MX93 provider
- Add NIC, A55 and ARM PLL clocks to i.MX93
- Fix i.MX8ULP XBAR_DIVBUS and AD_SLOW clock parents
- Use "divider closest" clock type for PLL4_PFD dividers on i.MX8ULP to
get more accurate clock rates
- Mark the MU0_Bi and TPM5 clocks on i.MX8ULP as critical
- Update some of the i.MX critical clocks flags to allow glitchless
on-the-fly rate change.
- Add I2C5 clock on Renesas R-Car V3H
- Exynos850: Add CMU_G3D clock controller for the Mali GPU
- Extract Exynos5433 (ARM64) clock controller power management code to
common driver parts
- Exynos850: make PMU_ALIVE_PCLK clock critical
- Add Audio, thermal, camera (CSI-2), Image Signal Processor/Channel
Selector (ISPCS), and video capture (VIN) clocks on Renesas R-Car V4H
- Add video capture (VIN) clocks on Renesas R-Car V3H
- Add Cortex-A53 System CPU (Z2) clocks on Renesas R-Car V3M and V3H
- Support for Stromer Plus PLL on Qualcomm IPQ5332
- Add a missing reset to Qualcomm QCM2290
- Migrate Qualcomm IPQ4019 to clk_parent_data
- Make USB GDSCs enter retention state when disabled on Qualcomm SM6375,
MSM8996 and MSM8998 SoCs
- Set floor rounding clk_ops for Qualcomm QCM2290 SDCC2 clk
- Add two EMAC GDSCs on Qualcomm SC8280XP
- Use shared rcg clk ops in Qualcomm SM6115 GCC
- Park Qualcomm SM8350 PCIe PIPE clks when disabled
- Add GDSCs to Qualcomm SC7280 LPASS audio clock controller
- Add missing XO clocks to Qualcomm MSM8226 and MSM8974
- Convert some Qualcomm clk DT bindings to YAML
- Reparenting fix for the clock supplying camera modules on Rockchip rk3399
- Mark more critical (bus-)clocks on Rockchip rk3588
-----BEGIN PGP SIGNATURE-----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=bTtL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing looks out of the ordinary in this batch of clk driver updates.
There are a couple patches to the core clk framework, but they're all
basically cleanups or debugging aids. The driver updates and new
additions are dominated in the diffstat by Qualcomm and MediaTek
drivers. Qualcomm gained a handful of new drivers for various SoCs,
and MediaTek gained a bunch of drivers for MT8188. The MediaTek
drivers are being modernized as well, so there are updates all over
that vendor's clk drivers. There's also a couple other new clk drivers
in here, for example the Starfive JH7110 SoC support is added.
Outside of the two major SoC vendors though, we have the usual
collection of non-critical fixes and cleanups to various clk drivers.
It's good to see that we're getting more cleanups and modernization
patches. Maybe one day we'll be able to properly split clk providers
from clk consumers.
Core:
- Print an informational message before disabling unused clks
New Drivers:
- BCM63268 timer clock and reset controller
- Frequency Hopping (FHCTL) on MediaTek MT6795, MT8173, MT8192 and
MT8195 SoCs
- Mediatek MT8188 SoC clk drivers
- Clock driver for Sunplus SP7021 SoC
- Clk driver support for Loongson-2 SoCs
- Clock driver for Skyworks Si521xx I2C PCIe clock generators
- Initial Starfive JH7110 clk/reset support
- Global clock controller drivers for Qualcomm SM7150, IPQ9574,
MSM8917 and IPQ5332 SoCs
- GPU clock controller drivers for SM6115, SM6125, SM6375 and SA8775P
SoCs
Updates:
- Shrink size of clk_fractional_divider a little
- Convert various clk drivers to devm_of_clk_add_hw_provider()
- Convert platform clk drivers to remove_new()
- Converted most Mediatek clock drivers to struct platform_driver
- MediaTek clock drivers can be built as modules
- Reimplement Loongson-1 clk driver with DT support
- Migrate socfpga clk driver to of_clk_add_hw_provider()
- Support for i3c clks on Aspeed ast2600 SoCs
- Add clock generic devm_clk_hw_register_gate_parent_data
- Add audiomix block control for i.MX8MP
- Add support for determine_rate to i.MX composite-8m
- Let the LCDIF Pixel clock of i.MX8MM and i.MX8MN set parent rate
- Provide clock name in error message for clk-gpr-mux on get parent
failure
- Drop duplicate imx_clk_mux_flags macro
- Register the i.MX8MP Media Disp2 Pix clock as bus clock
- Add Media LDB root clock to i.MX8MP
- Make i.MX8MP nand_usdhc_bus clock as non-critical
- Fix the rate table for i.MX fracn-gppll
- Disable HW control for the fracn-gppll in order to be controlled by
register write
- Add support for interger PLL in fracn-gppll
- Add mcore_booted module parameter to i.MX93 provider
- Add NIC, A55 and ARM PLL clocks to i.MX93
- Fix i.MX8ULP XBAR_DIVBUS and AD_SLOW clock parents
- Use "divider closest" clock type for PLL4_PFD dividers on i.MX8ULP
to get more accurate clock rates
- Mark the MU0_Bi and TPM5 clocks on i.MX8ULP as critical
- Update some of the i.MX critical clocks flags to allow glitchless
on-the-fly rate change.
- Add I2C5 clock on Renesas R-Car V3H
- Exynos850: Add CMU_G3D clock controller for the Mali GPU
- Extract Exynos5433 (ARM64) clock controller power management code
to common driver parts
- Exynos850: make PMU_ALIVE_PCLK clock critical
- Add Audio, thermal, camera (CSI-2), Image Signal Processor/Channel
Selector (ISPCS), and video capture (VIN) clocks on Renesas R-Car
V4H
- Add video capture (VIN) clocks on Renesas R-Car V3H
- Add Cortex-A53 System CPU (Z2) clocks on Renesas R-Car V3M and V3H
- Support for Stromer Plus PLL on Qualcomm IPQ5332
- Add a missing reset to Qualcomm QCM2290
- Migrate Qualcomm IPQ4019 to clk_parent_data
- Make USB GDSCs enter retention state when disabled on Qualcomm
SM6375, MSM8996 and MSM8998 SoCs
- Set floor rounding clk_ops for Qualcomm QCM2290 SDCC2 clk
- Add two EMAC GDSCs on Qualcomm SC8280XP
- Use shared rcg clk ops in Qualcomm SM6115 GCC
- Park Qualcomm SM8350 PCIe PIPE clks when disabled
- Add GDSCs to Qualcomm SC7280 LPASS audio clock controller
- Add missing XO clocks to Qualcomm MSM8226 and MSM8974
- Convert some Qualcomm clk DT bindings to YAML
- Reparenting fix for the clock supplying camera modules on Rockchip
rk3399
- Mark more critical (bus-)clocks on Rockchip rk3588"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (290 commits)
clk: qcom: gcc-sc8280xp: Add EMAC GDSCs
clk: starfive: Delete the redundant dev_set_drvdata() in JH7110 clock drivers
clk: rockchip: rk3588: make gate linked clocks critical
clk: qcom: dispcc-qcm2290: Remove inexistent DSI1PHY clk
clk: qcom: add the GPUCC driver for sa8775p
dt-bindings: clock: qcom: describe the GPUCC clock for SA8775P
clk: qcom: gcc-sm8350: fix PCIe PIPE clocks handling
clk: qcom: lpassaudiocc-sc7280: Add required gdsc power domain clks in lpass_cc_sc7280_desc
clk: qcom: lpasscc-sc7280: Skip qdsp6ss clock registration
dt-bindings: clock: qcom,sc7280-lpasscc: Add qcom,adsp-pil-mode property
clk: starfive: Avoid casting iomem pointers
clk: microchip: fix potential UAF in auxdev release callback
clk: qcom: rpm: Use managed `of_clk_add_hw_provider()`
clk: mediatek: fhctl: Mark local variables static
clk: sifive: make SiFive clk drivers depend on ARCH_ symbols
clk: uniphier: Use managed `of_clk_add_hw_provider()`
clk: si5351: Use managed `of_clk_add_hw_provider()`
clk: si570: Use managed `of_clk_add_hw_provider()`
clk: si514: Use managed `of_clk_add_hw_provider()`
clk: lmk04832: Use managed `of_clk_add_hw_provider()`
...
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230312161512.2715500-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Each entry in the clock table specifies a number of individual bits in
registers, for contolling clock reset, gaiting, etc. These reg/bit were
packed into a u16 to save space. The combined value is difficult to
understand when reviewing the clock table entries.
Introduce a "struct regbit" which still occupies only 16 bits, but
allows the register and bit values to be specified explicitly. Convert
all previous uses of u16 for reg/bit into "struct regbit".
The bulk of this patch converts the clock table to use struct regbit,
making use of the RB() helper macro. The conversion was automated by
script, and as a further verification, the compiled binary of the table
was compared before/after the change (with objdump -D).
The clk_rdesc_set() function now checks for zero reg/bit internally.
This allows callers of that function to remove those checks.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-5-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Drop three unused fields from the clock descriptor structure, and update
the macros for filling such structures accordingly.
The values for such fields are kept in the source code, now unused, in
case they are needed later.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-3-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Several small readability improvements:
- Move enum gate_type definition up and add comments to each field.
- Use this enum instead of generic uint32_t type in clock desc struct.
- Tidy up bitfield syntax and comments in clock desc structure
- Reformat macros for building clock desc to have one assignment per line
There is no functional change.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-2-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the R-Car Series, 3rd Generation Hardware User’s Manual
Rev. 2.30, the parent clock of the Video Input Module (VIN) on R-Car D3
is S3D1. Update the driver to match the documentation.
This has no functional impact, as both S1D2 and S3D1 have the same clock
rate, and are always-on clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/9b655843a260e06fa6f3349cdafac180e2bf38a5.1676368776.git.geert+renesas@glider.be
Add the VIN module clocks, which are used by the VIN modules on the
Renesas R-Car V3H (R8A77980) SoC.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230211153026.3898491-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the VIN module clocks, which are used by the VIN modules on the
Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230211143655.3809756-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the ISPCS0 and ISPCS1 module clocks, which are used by the ISPCS
modules on the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230211143655.3809756-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the CSI core clock and the CSI40 and CSI41 module clocks, which are
used by the CSI-2 Interfaces on the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230211143655.3809756-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the module clock used by the Thermal Sensor/Chip Internal Voltage
Monitor/Core Voltage Monitor (THS/CIVM/CVM) on the Renesas R-Car V4H
(R8A779G0) SoC.
Based on a large patch in the BSP by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/59461effd0d9f7a39e0c91352c87f2b7071b1891.1675958536.git.geert+renesas@glider.be
