[ Upstream commit dce0919c83 ]
As per the hardware team, TIEN and TINT source should not set at the same
time due to a possible hardware race leading to spurious IRQ.
Currently on some scenarios hardware settings for TINT detection is not in
sync with TINT source as the enable/disable overrides source setting value
leading to hardware inconsistent state. For eg: consider the case GPIOINT0
is used as TINT interrupt and configuring GPIOINT5 as edge type. During
rzg2l_irq_set_type(), TINT source for GPIOINT5 is set. On disable(),
clearing of the entire bytes of TINT source selection for GPIOINT5 is same
as GPIOINT0 with TIEN disabled. Apart from this during enable(), the
setting of GPIOINT5 with TIEN results in spurious IRQ as due to a HW race,
it is possible that IP can use the TIEN with previous source value
(GPIOINT0).
So, just update TIEN during enable/disable as TINT source is already set
during rzg2l_irq_set_type(). This will make the consistent hardware
settings for detection method tied with TINT source and allows to simplify
the code.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 853a603030 ]
RZ/G2L interrupt chips require that the interrupt is masked before changing
the NMI, IRQ, TINT interrupt settings. Aside of that, after setting an edge
trigger type it is required to clear the interrupt status register in order
to avoid spurious interrupts.
The current implementation fails to do either of that and therefore is
prone to generate spurious interrupts when setting the trigger type.
Address this by:
- Ensuring that the interrupt is masked at the chip level across the
update for the TINT chip
- Clearing the interrupt status register after updating the trigger mode
for edge type interrupts
[ tglx: Massaged changelog and reverted the spin_lock_irqsave() change as
the set_type() callback is always called with interrupts disabled. ]
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eca4731cc ]
There are 2 TITSR registers available on the IA55 interrupt controller.
Add a macro that retrieves the TITSR register offset based on it's
index. This macro is useful in when adding suspend/resume support so both
TITSR registers can be accessed in a for loop.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20231120111820.87398-7-claudiu.beznea.uj@bp.renesas.com
Stable-dep-of: 853a603030 ("irqchip/renesas-rzg2l: Prevent spurious interrupts when setting trigger type")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eec61df55 ]
The irq_eoi() callback of the RZ/G2L interrupt chip clears the relevant
interrupt cause bit in the TSCR register by writing to it.
This write is not sufficient because the write is posted and therefore not
guaranteed to immediately clear the bit. Due to that delay the CPU can
raise the just handled interrupt again.
Prevent this by reading the register back which causes the posted write to
be flushed to the hardware before the read completes.
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef88eefb1a ]
The RZ/G2L manual (chapter "IRQ Status Control Register (ISCR)") describes
the operation to clear interrupts through the ISCR register as follows:
[Write operation]
When "Falling-edge detection", "Rising-edge detection" or
"Falling/Rising-edge detection" is set in IITSR:
- In case ISTAT is 1
0: IRQn interrupt detection status is cleared.
1: Invalid to write.
- In case ISTAT is 0
Invalid to write.
When "Low-level detection" is set in IITSR.:
Invalid to write.
Take the interrupt type into account when clearing interrupts through the
ISCR register to avoid writing the ISCR when the interrupt type is level.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231120111820.87398-6-claudiu.beznea.uj@bp.renesas.com
Stable-dep-of: 9eec61df55 ("irqchip/renesas-rzg2l: Flush posted write in irq_eoi()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic to clear the TINT interrupt source in rzg2l_irqc_irq_disable()
is wrong as the mask is correct only for LSB on the TSSR register.
This issue is found when testing with two TINT interrupt sources. So fix
the logic for all TINTs by using the macro TSSEL_SHIFT() to multiply
tssr_offset with 8.
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230918122411.237635-2-biju.das.jz@bp.renesas.com
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Add a driver for the Renesas RZ/G2L Interrupt Controller.
This supports external pins being used as interrupts. It supports
one line for NMI, 8 external pins and 32 GPIO pins (out of 123)
to be used as IRQ lines.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220707182314.66610-4-prabhakar.mahadev-lad.rj@bp.renesas.com
