The UVC rev1.5 spec has requirements with data payload as below, take HS
Isoc transfer as example (2.4.3.2.2 Sample Isochronous Transfers):
+-----+ +----+ +---+-------+ +----+ +-------+ +----+ +-------+ +-----+
| SOF | | IN | | H | DATA2 | | IN | | DATA1 | | IN | | DATA0 | | SOF |
+-----+ +----+ +---+-------+ +----+ +-------+ +----+ +-------+ +-----+
\
Payload Header (8 bytes)
Three DATA packets need to be sent to the USB bus within 1 micro-frame.
However, the start address of payload header and DATA2 passed from uvc
layer may be not 4K page-aligned when using scatterlist.
The sgs may have below formats:
sgs:
- sg[0]: 8 bytes (payload header)
- sg[1]: 3064 bytes (payload)
In this case, the udc needs 2 dTDs to send data out. However, the packets
on USB bus will show as:
+-----+ +----+ +---+ +-----+ +----+ +-------+ +----+ +-------+ +----+ +-------+ +-----+
| SOF | | IN | | H | | SOF | | IN | | DATA2 | | IN | | DATA1 | | IN | | DATA0 | | SOF |
+-----+ +----+ +---+ +-----+ +----+ +-------+ +----+ +-------+ +----+ +-------+ +-----+
\
Payload Header (8 bytes)
This behavior is unexpected since the host will not recognize uvc data
correctly. The root cause should be dTD doesn't support scatterlist very
well. Such as (1) doesn't support one DATA packet span two or more dTD
(2) doesn't support specify offset for page1-4.
So in order for uvc gadget works properly, disable sg_support when it has
uvc function, or else enable it.
Note: most of the functions use sg_support after bind stage, except uvc
which uses sg_support when call bind(), so if a function in future
also uses sg_support when call bind(), it will be limited to non-sg
way.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Changed the page alignment check within the prepare_td_for_sg() function
since the first buffer could not be page size aligned, so the check is
only performed for the following buffers.
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
When power is recycled in usb controller during system power management,
the controller will recognize it and switch role if role has been changed
during power lost. In current design, it will be completed in resume()
function. However, this may bring issues since usb class devices have
their pm operations too and these device's resume() functions are still
not being called at this point. When usb controller recognized host role
should be stopped, these usb class devices will be removed at this point.
But these usb class devices can't be removed in some cases, such as scsi
devices. Since scsi driver may sync data to U-disk, however it will block
there because scsi drvier can only handle pm request when is in suspended
state. Therefore, there may exist a dependency between ci_resume() and usb
class device's resume(). To break this potential dependency, we need to
handle power lost work in a workqueue.
Fixes: 74494b3321 ("usb: chipidea: core: add controller resume support when controller is powered off")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240119123537.3614838-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
This is the 6.6.2 stable release
* tag 'v6.6.2': (634 commits)
Linux 6.6.2
btrfs: make found_logical_ret parameter mandatory for function queue_scrub_stripe()
btrfs: use u64 for buffer sizes in the tree search ioctls
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
drivers/clk/imx/clk-imx8mq.c
drivers/clk/imx/clk-imx8qxp.c
drivers/media/i2c/ov5640.c
drivers/misc/pci_endpoint_test.c
There are two sets (HSIO blkctl and USB non-core) of wakeup setting when
HSIO blkctl exists. To support wakup when HSIO domain power is lost, HSIO
blkctl wakup handling is a must. This will add the wakup handling for HSIO
blkctl cases.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Besides normal USB interrupt generated by Chipidea controller, another
USB wakeup can also be generated. In previous cases, these two interrupts
are bound to one irq line. However, the wakeup interrupt has a dedicated
irq line in latest i.MX95 platform. This will add wakup irq handling for
this case to support various wakeup cases.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
[ Upstream commit 2ae61a2562 ]
The USB host on Tegra3 works with 32-bit alignment. Previous code tried
to align the buffer, but it did align the wrapper struct instead, so
the buffer was at a constant offset of 8 bytes (two pointers) from
expected alignment. Since kmalloc() guarantees at least 8-byte
alignment already, the alignment-extending is removed.
Fixes: fc53d52790 ("usb: chipidea: tegra: Support host mode")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/a0d917d492b1f91ee0019e68b8e8bca9c585393f.1695934946.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ab8716713 ]
Tegra USB controllers seem to issue DMA in full 32-bit words only and thus
may overwrite unevenly-sized buffers. One such occurrence is detected by
SLUB when receiving a reply to a 1-byte buffer (below). Fix this by
allocating a bounce buffer also for buffers with sizes not a multiple of 4.
=============================================================================
BUG kmalloc-64 (Tainted: G B ): kmalloc Redzone overwritten
-----------------------------------------------------------------------------
0x8555cd02-0x8555cd03 @offset=3330. First byte 0x0 instead of 0xcc
Allocated in usb_get_status+0x2b/0xac age=1 cpu=3 pid=41
__kmem_cache_alloc_node+0x12f/0x1e4
__kmalloc+0x33/0x8c
usb_get_status+0x2b/0xac
hub_probe+0x5e9/0xcec
usb_probe_interface+0xbf/0x21c
really_probe+0xa5/0x2c4
__driver_probe_device+0x75/0x174
driver_probe_device+0x31/0x94
__device_attach_driver+0x65/0xc0
bus_for_each_drv+0x4b/0x74
__device_attach+0x69/0x120
bus_probe_device+0x65/0x6c
device_add+0x48b/0x5f8
usb_set_configuration+0x37b/0x6b4
usb_generic_driver_probe+0x37/0x68
usb_probe_device+0x35/0xb4
Slab 0xbf622b80 objects=21 used=18 fp=0x8555cdc0 flags=0x800(slab|zone=0)
Object 0x8555cd00 @offset=3328 fp=0x00000000
Redzone 8555ccc0: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 8555ccd0: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 8555cce0: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 8555ccf0: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 8555cd00: 01 00 00 00 cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 8555cd10: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 8555cd20: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 8555cd30: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 8555cd40: cc cc cc cc ....
Padding 8555cd74: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZ
CPU: 3 PID: 41 Comm: kworker/3:1 Tainted: G B 6.6.0-rc1mq-00118-g59786f827ea1 #1115
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: usb_hub_wq hub_event
[<8010ca28>] (unwind_backtrace) from [<801090a5>] (show_stack+0x11/0x14)
[<801090a5>] (show_stack) from [<805da2fb>] (dump_stack_lvl+0x4d/0x7c)
[<805da2fb>] (dump_stack_lvl) from [<8026464f>] (check_bytes_and_report+0xb3/0xe4)
[<8026464f>] (check_bytes_and_report) from [<802648e1>] (check_object+0x261/0x290)
[<802648e1>] (check_object) from [<802671b1>] (free_to_partial_list+0x105/0x3f8)
[<802671b1>] (free_to_partial_list) from [<80268613>] (__kmem_cache_free+0x103/0x128)
[<80268613>] (__kmem_cache_free) from [<80425a67>] (usb_get_status+0x73/0xac)
[<80425a67>] (usb_get_status) from [<80421b31>] (hub_probe+0x5e9/0xcec)
[<80421b31>] (hub_probe) from [<80428bbb>] (usb_probe_interface+0xbf/0x21c)
[<80428bbb>] (usb_probe_interface) from [<803ee13d>] (really_probe+0xa5/0x2c4)
[<803ee13d>] (really_probe) from [<803ee3d1>] (__driver_probe_device+0x75/0x174)
[<803ee3d1>] (__driver_probe_device) from [<803ee501>] (driver_probe_device+0x31/0x94)
usb 1-1: device descriptor read/8, error -71
Fixes: fc53d52790 ("usb: chipidea: tegra: Support host mode")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/ef8466b834c1726f5404c95c3e192e90460146f8.1695934946.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
"f71e5cddd693 LF-7734 usb: chipidea: core: handle usb role switch in a
common way" is defective when switch usb role in non-lpm mode, the better
way is to revert it but keep part codes in ci_extcon_wakeup_int().
Fixes: f71e5cddd6 ("LF-7734 usb: chipidea: core: handle usb role switch in a common way")
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Some platform using chipidea chip may keep 32KHz wakeup clock always
on without usb driver intervention. And some may need driver to handle
this clock. This patch will get wakeup clock to make controller work
correctlly.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
After the chipidea driver introduce extcon for id and vbus, it's able
to wakeup from another irq source, in case the system with extcon ID
cable, wakeup from usb ID cable and device removal, the usb device
disconnect irq may come firstly before the extcon notifier while system
resume, so we will get 2 "wakeup" irq, one for usb device disconnect;
and one for extcon ID cable change(real wakeup event), current driver
treat them as 2 successive wakeup irq so can't handle it correctly, then
finially the usb irq can't be enabled. This patch adds a check to bypass
further usb events before controller resume finished to fix it.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
On some imx host, if USB PHY is active when bus suspended, host may
have problem on taking over resume signal of remote wakeup from usb
device, resolve this by making PHY enter low power mode right after
bus suspended.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Some chipidea hardware needs to disable low power mode for controller
due to IC issue or hardware issue, add one quirk for it.
Acked-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
[ Aisheng: update to use YAML format ]
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
When the usb in idle, it calls release_bus_req.
When the usb is going to use, it calls request_bus_req.
This is a rework patch of ENGR00286459 and ENGR00286926.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some NXP processors using ChipIdea USB IP have a bug when frame babble is
detected.
Issue description:
In USB camera test, our controller is host in HS mode. In ISOC IN, when
device sends data across the micro frame, it causes the babble in host
controller. This will clear the PE bit. In spec, it also requires to set
the PEC bit and then set the PCI bit. Without the PCI interrupt, the
software does not know the PE is cleared.
This will add a flag CI_HDRC_HAS_PORTSC_PEC_MISSED to some impacted
platform datas. And the ehci host driver will assert PEC by SW when
specific conditions are satisfied.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230809024432.535160-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NULL initialization of the pointers assigned by kzalloc() first is
not necessary, because if the kzalloc() failed, the pointers will be
assigned NULL, otherwise it works as usual. so remove it.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230804093253.91647-4-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-2-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add USB PHY event for below situation:
- usb role changed
- vbus connect
- vbus disconnect
- gadget driver is enumerated
USB PHY driver can get the last event after above situation occurs
and deal with different situations.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627110353.1879477-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases, the user may need to tune the rise/fall time of the
high-speed transmitter waveform for USB Certification. This will add
a parameter for this purpose. The value will be fetched from dtb and
finally written to the register.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627112126.1882666-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current driver, the value of tuning parameter will not take effect
if samsung,picophy-* is assigned as 0. Because 0 is also a valid value
acccording to the description of USB_PHY_CFG1 register, this will improve
the logic to let it work.
Fixes: 58a3cefb38 ("usb: chipidea: imx: add two samsung picophy parameters tuning implementation")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627112126.1882666-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB PHY DPDM wakeup bit is enabled by default, when USB wakeup
is not required(/sys/.../wakeup is disabled), this bit should be
disabled, otherwise we will have unexpected wakeup if do USB device
connect/disconnect while system sleep.
This bit can be enabled for both host and device mode.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230517081907.3410465-3-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we use bvalid for vbus wakeup source, to save power when
suspend, turn off the vbus comparator for imx7d and imx8mm.
Below is this bit description from RM of iMX8MM
"VBUS Valid Comparator Enable:
This signal controls the USB OTG PHY VBUS Valid comparator which
indicates whether the voltage on the USB_OTG*_VBUS pin is below
the VBUS Valid threshold. The VBUS Valid threshold is nominally
4.75V on this USB PHY. The VBUS Valid threshold can be adjusted
using the USBNC_OTGn_PHY_CFG1[OTGTUNE0] bit field. Status of the
VBUS Valid comparator, when it is enabled, is reported on the
USBNC_OTGn_PHY_STATUS[VBUS_VLD] bit.
When OTGDISABLE0 (USBNC_USB_OTGx_PHY_CFG2[10])is set to 1'b0 and
DRVVBUS0 is set to 1'b1, the Bandgap circuitry and VBUS Valid
comparator are powered, even in Suspend or Sleep mode.
DRVVBUS0 should be reset to 1'b0 when the internal VBUS Valid comparator
is not required, to reduce quiescent current in Suspend or Sleep mode.
- 0 The VBUS Valid comparator is disabled
- 1 The VBUS Valid comparator is enabled"
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230517081907.3410465-2-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dedicated imx8ulp usb compatible to remove QoS request
since imx8ulp has no such limitation of imx7ulp: DMA will
not work if system enters idle.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230530104007.1294702-2-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove one duplicated definition of MX7D_USB_OTG_PHY_CFG1.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230517081907.3410465-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From the comment of ci_usb_phy_init, it returns an error code if
usb_phy_init has failed, and it should do some clean up, not just
return directly.
Fix this by goto the error handling.
Fixes: 74475ede78 ("usb: chipidea: move PHY operation to core")
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Yinhao Hu <dddddd@hust.edu.cn>
Link: https://lore.kernel.org/r/20230412055852.971991-1-dddddd@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The changes brought by commit 73de934401 have been inadvertidly
removed, causing ci_hdrc_imx's probe to be loaded before usbmisc_imx's,
despite ci_hdrc_imx needing usbmisc_imx.
This condition may cause unexpected behaviors, especially when the
ChipIdea node is being referred to under /sys/class/udc/:
$ ls -l /sys/class/udc/
$
when it should show as the following:
$ ls -l /sys/class/udc/
ci_hdrc.0 -> ../../devices/[...]/ci_hdrc.0/udc/ci_hdrc.0
Some userspace tools may depend on this feature[1].
[1]: 69029e71b0/linuxrc (L148)
Fixes: 95caa2ae70 ("usb: chipidea: allow disabling glue drivers if EMBEDDED")
Signed-off-by: Thomas Ballasi <thomas.ballasi@savoirfairelinux.com>
Link: https://lore.kernel.org/r/20230330221637.1605161-1-thomas.ballasi@savoirfairelinux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes here, and the USB gadget update for future
development patches to be based on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user may call role_store() when driver is handling
ci_handle_id_switch() which is triggerred by otg event or power lost
event. Unfortunately, the controller may go into chaos in this case.
Fix this by protecting it with mutex lock.
Fixes: a932a8041f ("usb: chipidea: core: add sysfs group")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230317061516.2451728-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should not return -EINVAL if the request role is the same with current
role, return non-error and without do anything instead.
Fixes: a932a8041f ("usb: chipidea: core: add sysfs group")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230317061516.2451728-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two 'role' file exist in different position but with totally same function.
1. /sys/devices/platform/soc@0/xxxxxxxx.usb/ci_hdrc.0/role
2. /sys/kernel/debug/usb/ci_hdrc.0/role
This will remove the 2rd redundant 'role' debug file (under debugfs) and
keep the one which is more closer to user.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230317061651.2457567-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20230310144729.1545857-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230202153235.2412790-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves merge conflicts as
reported in linux-next in the following files:
drivers/usb/host/xhci.c
drivers/usb/host/xhci.h
drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After successfully probed, ci->role_switch would only be NULL or a valid
pointer. IS_ERR(ci->role_switch) will always return 0. So no need to wrap
it with IS_ERR, otherwise the logic is wrong.
Fixes: e1b5d2bed6 ("usb: chipidea: core: handle usb role switch in a common way")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20221215055409.3760523-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221212212717.3774606-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM_SLEEP is not set, the following error will be shown up
when build kernel:
error: 'ci_handle_power_lost' defined but not used.
This will move ci_handle_power_lost() to an area wrapped by
CONFIG_PM_SLEEP.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Fixes: 74494b3321 ("usb: chipidea: core: add controller resume support when controller is powered off")
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221026121157.1491302-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in ci_otg_del_timer(), the process is
shown below:
(thread 1) | (thread 2)
ci_otg_del_timer() | ci_otg_hrtimer_func()
... |
spin_lock_irqsave() //(1) | ...
... |
hrtimer_cancel() | spin_lock_irqsave() //(2)
(block forever)
We hold ci->lock in position (1) and use hrtimer_cancel() to
wait ci_otg_hrtimer_func() to stop, but ci_otg_hrtimer_func()
also need ci->lock in position (2). As a result, the
hrtimer_cancel() in ci_otg_del_timer() will be blocked forever.
This patch extracts hrtimer_cancel() from the protection of
spin_lock_irqsave() in order that the ci_otg_hrtimer_func()
could obtain the ci->lock.
What`s more, there will be no race happen. Because the
"next_timer" is always under the protection of
spin_lock_irqsave() and we only check whether "next_timer"
equals to NUM_OTG_FSM_TIMERS in the following code.
Fixes: 3a316ec4c9 ("usb: chipidea: use hrtimer for otg fsm timers")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220918033312.94348-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx7ulp can shutdown domain power supply if none of peripheral in this
domain is registered as wakeup source, this patch add related power lost
check API.
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20221013151442.3262951-9-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx7d can shutdown domain power supply if none of peripheral in this
domain is registered as wakeup source, this patch add related codes to
check if power is lost.
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20221013151442.3262951-8-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
