Currently, driver gets interrupt number directly from ice_pf::msix_entries
array. Use helper function dedicated to do just that.
While at it use a variable to store interrupt number in
ice_free_irq_msix_misc instead of calling the helper function twice.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Keep interrupt handling code in a dedicated file. This helps keep driver
structured better and prepares for more functionality added to this file.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Filters shouldn't be removed in VSI rebuild path. Removing them on PF
VSI results in no rule for PF MAC after changing for example queues
amount.
Remove all filters only in the VSI remove flow. As unload should also
cause the filter to be removed introduce, a new function ice_stop_eth().
It will unroll ice_start_eth(), so remove filters and close VSI.
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
RDMA is not supported in ice on a PF that has been added to a bonded
interface. To enforce this, when an interface enters a bond, we unplug
the auxiliary device that supports RDMA functionality. This unplug
currently happens in the context of handling the netdev bonding event.
This event is sent to the ice driver under RTNL context. This is causing
a deadlock where the RDMA driver is waiting for the RTNL lock to complete
the removal.
Defer the unplugging/re-plugging of the auxiliary device to the service
task so that it is not performed under the RTNL lock context.
Cc: stable@vger.kernel.org # 6.1.x
Reported-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Link: https://lore.kernel.org/netdev/CAK8fFZ6A_Gphw_3-QMGKEFQk=sfCw1Qmq0TVZK3rtAi7vb621A@mail.gmail.com/
Fixes: 5cb1ebdbc4 ("ice: Fix race condition during interface enslave")
Fixes: 4eace75e08 ("RDMA/irdma: Report the correct link speed")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230310194833.3074601-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main loop in __ice_clean_ctrlq first checks if a VF might be malicious
before calling ice_vc_process_vf_msg(). This results in duplicate code in
both functions to obtain a reference to the VF, and exports the
ice_is_malicious_vf() from ice_virtchnl.c unnecessarily.
Refactor ice_is_malicious_vf() to be a static function that takes a pointer
to the VF. Call this in ice_vc_process_vf_msg() just after we obtain a
reference to the VF by calling ice_get_vf_by_id.
Pass the mailbox data from the __ice_clean_ctrlq function into
ice_vc_process_vf_msg() instead of calling ice_is_malicious_vf().
This reduces the number of exported functions and avoids the need to obtain
the VF reference twice for every mailbox message.
Note that the state check for ICE_VF_STATE_DIS is kept in
ice_is_malicious_vf() and we call this before checking that state in
ice_vc_process_vf_msg. This is intentional, as we stop responding to VF
messages from a VF once we detect that it may be overflowing the mailbox.
This ensures that we continue to silently ignore the message as before
without responding via ice_vc_send_msg_to_vf().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_is_malicious_vf() function takes information about the current
state of the mailbox during a single interrupt. This information includes
the number of messages processed so far, as well as the number of pending
messages not yet processed.
A future refactor is going to make ice_vc_process_vf_msg() call
ice_is_malicious_vf() instead of having it called separately in ice_main.c
This change will require passing all the necessary arguments into
ice_vc_process_vf_msg().
To make this simpler, have the main loop fill in the struct ice_mbx_data
and pass that rather than passing in the num_msg_proc and num_msg_pending.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now that we no longer depend on the number of VFs being allocated, we can
move the ice_mbx_init_snapshot function earlier. This will be required by
Scalable IOV as we will not be calling ice_sriov_configure for Scalable
VFs.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-02-14 (ice)
This series contains updates to ice driver only.
Karol extends support for GPIO pins to E823 devices.
Daniel Vacek stops processing of PTP packets when link is down.
Pawel adds support for BIG TCP for IPv6.
Tony changes return type of ice_vsi_realloc_stat_arrays() as it always
returns success.
Zhu Yanjun updates kdoc stating supported TLVs.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Mention CEE DCBX in code comment
ice: Change ice_vsi_realloc_stat_arrays() to void
ice: add support BIG TCP on IPv6
ice/ptp: fix the PTP worker retrying indefinitely if the link went down
ice: Add GPIO pin support for E823 products
====================
Link: https://lore.kernel.org/r/20230214213003.2117125-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable sending BIG TCP packets on IPv6 in the ice driver using generic
ipv6_hopopt_jumbo_remove helper for stripping HBH header.
Tested:
netperf -t TCP_RR -H 2001:db8:0:f101::1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,TRANSACTION_RATE
Tested on two different setups. In both cases, the following settings were
applied after loading the changed driver:
ip link set dev enp175s0f1np1 gso_max_size 130000
ip link set dev enp175s0f1np1 gro_max_size 130000
ip link set dev enp175s0f1np1 mtu 9000
First setup:
Before:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
134 279 410 3961.584
After:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
135 178 216 6093.404
The other setup:
Before:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
218 414 478 2944.765
After:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
146 238 266 4700.596
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was a problem reported to us where the addition of a VF with an IPv6
address ending with a particular sequence would cause the parent device on
the PF to no longer be able to respond to neighbor discovery packets.
In this case, we had an ovs-bridge device living on top of a VLAN, which
was on top of a PF, and it would not be able to talk anymore (the neighbor
entry would expire and couldn't be restored).
The root cause of the issue is that if the PF is asked to be in IFF_PROMISC
mode (promiscuous mode) and it had an ipv6 address that needed the
33:33:ff:00:00:04 multicast address to work, then when the VF was added
with the need for the same multicast address, the VF would steal all the
traffic destined for that address.
The ice driver didn't auto-subscribe a request of IFF_PROMISC to the
"multicast replication from other port's traffic" meaning that it won't get
for instance, packets with an exact destination in the VF, as above.
The VF's IPv6 address, which adds a "perfect filter" for 33:33:ff:00:00:04,
results in no packets for that multicast address making it to the PF (which
is in promisc but NOT "multicast replication").
The fix is to enable "multicast promiscuous" whenever the driver is asked
to enable IFF_PROMISC, and make sure to disable it when appropriate.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCY+bZrwAKCRDbK58LschI
gzi4AP4+TYo0jnSwwkrOoN9l4f5VO9X8osmj3CXfHBv7BGWVxAD/WnvA3TDZyaUd
agIZTkRs6BHF9He8oROypARZxTeMLwM=
=nO1C
-----END PGP SIGNATURE-----
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When hardware is reset, the VF relies on the VFGEN_RSTAT register to detect
when the VF is finished resetting. This is a tri-state register where 0
indicates a reset is in progress, 1 indicates the hardware is done
resetting, and 2 indicates that the software is done resetting.
Currently the PF driver relies on the device hardware resetting VFGEN_RSTAT
when a global reset occurs. This works ok, but it does mean that the VF
might not immediately notice a reset when the driver first detects that the
global reset is occurring.
This is also problematic for Scalable IOV, because there is no read/write
equivalent VFGEN_RSTAT register for the Scalable VSI type. Instead, the
Scalable IOV VFs will need to emulate this register.
To support this, introduce a new VF operation, clear_reset_state, which is
called when the PF driver first detects a global reset. The Single Root IOV
implementation can just write to VFGEN_RSTAT to ensure it's cleared
immediately, without waiting for the actual hardware reset to begin. The
Scalable IOV implementation will use this as part of its tracking of the
reset status to allow properly reporting the emulated VFGEN_RSTAT to the VF
driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_vsi_setup function, ice_vsi_alloc, and ice_vsi_cfg functions have
grown a large number of parameters. These parameters are used to initialize
a new VSI, as well as re-configure an existing VSI
Any time we want to add a new parameter to this function chain, even if it
will usually be unset, we have to change many call sites due to changing
the function signature.
A future change is going to refactor ice_vsi_alloc and ice_vsi_cfg to move
the VSI configuration and initialization all into ice_vsi_cfg.
Before this, refactor the VSI setup flow to use a new ice_vsi_cfg_params
structure. This will contain the configuration (mainly pointers) used to
initialize a VSI.
Pass this from ice_vsi_setup into the related functions such as
ice_vsi_alloc, ice_vsi_cfg, and ice_vsi_cfg_def.
Introduce a helper, ice_vsi_to_params to convert an existing VSI to the
parameters used to initialize it. This will aid in the flows where we
rebuild an existing VSI.
Since we also pass the ICE_VSI_FLAG_INIT to more functions which do not
need (or cannot yet have) the VSI parameters, lets make this clear by
renaming the function parameter to vsi_flags and using a u32 instead of a
signed integer. The name vsi_flags also makes it clear that we may extend
the flags in the future.
This change will make it easier to refactor the setup flow in the future,
and will reduce the complexity required to add a new parameter for
configuration in the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_vsi_cfg() is called from different contexts:
1) VSI exsist in HW, but it is reconfigured, because of changing queues
for example -> update instead of init should be used
2) VSI doesn't exsist, because rest has happened -> init command should
be sent
To support both cases pass boolean value which will store information
what type of command has to be sent to HW.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In deconfig VSI shouldn't be deleted from hw.
Rewrite VSI delete function to reflect that sometimes it is only needed
to remove VSI from hw without freeing the memory:
ice_vsi_delete() -> delete from HW and free memory
ice_vsi_delete_from_hw() -> delete only from HW
Value returned from ice_vsi_free() is never used. Change return type to
void.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Part of code from probe can be reused in reload flow. Move this code to
separate function. Create unroll functions for each part of
initialization, like: ice_init_dev() and ice_deinit_dev(). It
simplifies unrolling and can be used in remove flow.
Avoid freeing port info as it could be reused in reload path.
Will be freed in remove path since is allocated via devm_kzalloc().
Also clean the remove path to reflect the init steps.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Main goal is to reuse the same functions in VSI config and rebuild
paths.
To do this split ice_vsi_setup into smaller pieces and reuse it during
rebuild.
ice_vsi_alloc() should only alloc memory, not set the default values
for VSI.
Move setting defaults to separate function. This will allow config of
already allocated VSI, for example in reload path.
The path is mostly moving code around without introducing new
functionality. Functions ice_vsi_cfg() and ice_vsi_decfg() were
added, but they are using code that already exist.
Use flag to pass information about VSI initialization during rebuild
instead of using boolean value.
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do few small cleanups:
1) Rename the function to reflect that it doesn't configure all things
related to VSI. ice_vsi_cfg_lan() better fits to what function is doing.
ice_vsi_cfg() can be use to name function that will configure whole VSI.
2) Remove unused ethtype field from VSI. There is no need to set
ethtype here, because it is never used.
3) Remove unnecessary check for ICE_VSI_CHNL. There is check for
ICE_VSI_CHNL in ice_vsi_get_qs, so there is no need to check it before
calling the function.
4) Simplify ice_vsi_alloc() call. There is no need to check the type of
VSI before calling ice_vsi_alloc(). For ICE_VSI_CHNL vf is always NULL
(ice_vsi_setup() is called with vf=NULL).
For ICE_VSI_VF or ICE_VSI_CTRL ch is always NULL and for other VSI types
ch and vf are always NULL.
5) Remove unnecessary call to ice_vsi_dis_irq(). ice_vsi_dis_irq() will
be called in ice_vsi_close() flow (ice_vsi_close() -> ice_vsi_down() ->
ice_vsi_dis_irq()). Remove unnecessary call.
6) Don't remove specific filters in release. All hw filters are removed
in ice_fltr_remove_alli(), which is always called in VSI release flow.
There is no need to remove only ethertype filters before calling
ice_fltr_remove_all().
7) Rename ice_vsi_clear() to ice_vsi_free(). As ice_vsi_clear() only
free memory allocated in ice_vsi_alloc() rename it to ice_vsi_free()
which better shows what function is doing.
8) Free coalesce param in rebuild. There is potential memory leak if
configuration of VSI lan fails. Free coalesce to avoid it.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Simplify probe flow by moving all RDMA related code to ice_init_rdma().
Unroll irq allocation if RDMA initialization fails.
Implement ice_deinit_rdma() and use it in remove flow.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.
Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.
Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.
Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)
Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.
Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.
Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Now that both ZC and standard XDP data paths stopped using Tx logic
based on next_dd and next_rs fields, we can safely remove these fields
and shrink Tx ring structure.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-13-maciej.fijalkowski@intel.com
Ice driver needs to be a bit reworked on Rx data path in order to
support multi-buffer XDP. For skb path, it currently works in a way that
Rx ring carries pointer to skb so if driver didn't manage to combine
fragmented frame at current NAPI instance, it can restore the state on
next instance and keep looking for last fragment (so descriptor with EOP
bit set). What needs to be achieved is that xdp_buff needs to be
combined in such way (linear + frags part) in the first place. Then skb
will be ready to go in case of XDP_PASS or BPF program being not present
on interface. If BPF program is there, it would work on multi-buffer
XDP. At this point xdp_buff resides directly on Rx ring, so given the
fact that skb will be built straight from xdp_buff, there will be no
further need to carry skb on Rx ring.
Besides removing skb pointer from Rx ring, lots of members have been
moved around within ice_rx_ring. First and foremost reason was to place
rx_buf with xdp_buff on the same cacheline. This means that once we
touch rx_buf (which is a preceding step before touching xdp_buff),
xdp_buff will already be hot in cache. Second thing was that xdp_rxq is
used rather rarely and it occupies a separate cacheline, so maybe it is
better to have it at the end of ice_rx_ring.
Other change that affects ice_rx_ring is the introduction of
ice_rx_ring::first_desc. Its purpose is twofold - first is to propagate
rx_buf->act to all the parts of current xdp_buff after running XDP
program, so that ice_put_rx_buf() that got moved out of the main Rx
processing loop will be able to tak an appriopriate action on each
buffer. Second is for ice_construct_skb().
ice_construct_skb() has a copybreak mechanism which had an explicit
impact on xdp_buff->skb conversion in the new approach when legacy Rx
flag is toggled. It works in a way that linear part is 256 bytes long,
if frame is bigger than that, remaining bytes are going as a frag to
skb_shared_info.
This means while memcpying frags from xdp_buff to newly allocated skb,
care needs to be taken when picking the destination frag array entry.
Upon the time ice_construct_skb() is called, when dealing with
fragmented frame, current rx_buf points to the *last* fragment, but
copybreak needs to be done against the first one. That's where
ice_rx_ring::first_desc helps.
When frame building spans across NAPI polls (DD bit is not set on
current descriptor and xdp->data is not NULL) with current Rx buffer
handling state there might be some problems.
Since calls to ice_put_rx_buf() were pulled out of the main Rx
processing loop and were scoped from cached_ntc to current ntc, remember
that now mentioned function relies on rx_buf->act, which is set within
ice_run_xdp(). ice_run_xdp() is called when EOP bit was found, so
currently we could put Rx buffer with rx_buf->act being *uninitialized*.
To address this, change scoping to rely on first_desc on both boundaries
instead.
This also implies that cleaned_count which is used as an input to
ice_alloc_rx_buffers() and tells how many new buffers should be refilled
has to be adjusted. If it stayed as is, what could happen is a case
where ntc would go over ntu.
Therefore, remove cleaned_count altogether and use against allocing
routine newly introduced ICE_RX_DESC_UNUSED() macro which is an
equivalent of ICE_DESC_UNUSED() dedicated for Rx side and based on
struct ice_rx_ring::first_desc instead of next_to_clean.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-11-maciej.fijalkowski@intel.com
This should have been used in there from day 1, let us address that
before introducing XDP multi-buffer support for Rx side.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-8-maciej.fijalkowski@intel.com
Rx path is going to be modified in a way that fragmented frame will be
gathered within xdp_buff in the first place. This approach implies that
underlying buffer has to provide tailroom for skb_shared_info. This is
currently the case when ring uses build_skb but not when legacy-rx knob
is turned on. This case configures 2k Rx buffers and has no way to
provide either headroom or tailroom - FWIW it currently has
XDP_PACKET_HEADROOM which is broken and in here it is removed. 2k Rx
buffers were used so driver in this setting was able to support 9k MTU
as it can chain up to 5 Rx buffers. With offset configuring HW writing
2k of a data was passing the half of the page which broke the assumption
of our internal page recycling tricks.
Now if above got fixed and legacy-rx path would be left as is, when
referring to skb_shared_info via xdp_get_shared_info_from_buff(),
packet's content would be corrupted again. Hence size of Rx buffer needs
to be lowered and therefore supported MTU. This operation will allow us
to keep the unified data path and with 8k MTU users (if any of
legacy-rx) would still be good to go. However, tendency is to drop the
support for this code path at some point.
Add ICE_RXBUF_1664 as vsi::rx_buf_len and ICE_MAX_FRAME_LEGACY_RX (8320)
as vsi::max_frame for legacy-rx. For bigger page sizes configure 3k Rx
buffers, not 2k.
Since headroom support is removed, disable data_meta support on legacy-rx.
When preparing XDP buff, rely on ice_rx_ring::rx_offset setting when
deciding whether to support data_meta or not.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-2-maciej.fijalkowski@intel.com
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this doesn't control interrupt generation by the Root Port; that
is controlled by the AER Root Error Command register, which is managed by
the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The PF controls the set of queues that the RDMA auxiliary_driver requests
resources from. The set_channel command will alter that pool and trigger a
reconfiguration of the VSI, which breaks RDMA functionality.
Prevent set_channel from executing when RDMA driver bound to auxiliary
device.
Adding a locked variable to pass down the call chain to avoid double
locking the device_lock.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit a286ba7387 ("ice: reorder PF/representor devlink
port register/unregister flows") moved the code to create
and destroy the devlink PF port. This was fine, but created
a corner case issue in the case of ice_register_netdev()
failing. In that case, the driver would end up calling
ice_devlink_destroy_pf_port() twice.
Additionally, it makes no sense to tie creation of the devlink
PF port to the creation of the netdev so separate out the
code to create/destroy the devlink PF port from the netdev
code. This makes it a cleaner interface.
Fixes: a286ba7387 ("ice: reorder PF/representor devlink port register/unregister flows")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230124005714.3996270-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There were a few places we had missed checking the VSI type to make sure
it was definitely a PF VSI, before calling setup functions intended only
for the PF VSI.
This doesn't fix any explicit bugs but cleans up the code in a few
places and removes one explicit != vsi->type check that can be
superseded by this code (it's a super set)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove a redundant null check, as vsi could not be null at this point.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_ptp_link_change function is currently only called for E822 based
hardware. Future changes are going to extend this function to perform
additional tasks on link change.
Always call this function, moving the E810 check from the callers down to
just before we call the E822-specific function required to restart the PHY.
This function also returns an error value, but none of the callers actually
check it. In general, the errors it produces are more likely systemic
problems such as invalid or corrupt port numbers. No caller checks these,
and so no warning is logged.
Re-order the flag checks so that ICE_FLAG_PTP is checked first. Drop the
unnecessary check for ICE_FLAG_PTP_SUPPORTED, as ICE_FLAG_PTP will not be
set except when ICE_FLAG_PTP_SUPPORTED is set.
Convert the port checks to WARN_ON_ONCE, in order to generate a kernel
stack trace when they are hit.
Convert the function to void since no caller actually checks these return
values.
Co-developed-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Resets may occur with or without user interaction. For example, a TX hang
or reconfiguration of parameters will result in a reset. During reset, the
VSI is freed, freeing any statistics structures inside as well. This would
create an issue for the user where a reset happens in the background,
statistics set to zero, and the user checks ring statistics expecting them
to be populated.
To ensure this doesn't happen, accumulate ring statistics over reset.
Define a new ring statistics structure, ice_ring_stats. The new structure
lives in the VSI's parent, preserving ring statistics when VSI is freed.
1. Define a new structure vsi_ring_stats in the PF scope
2. Allocate/free stats only during probe, unload, or change in ring size
3. Replace previous ring statistics functionality with new structure
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Resets happen with or without user interaction. For example, incidents
such as TX hang or a reconfiguration of parameters will result in a reset.
During reset, hardware and software statistics were set to zero. This
created an issue for the user where a reset happens in the background,
statistics set to zero, and the user checks statistics expecting them to
be populated.
To ensure this doesn't happen, keep accumulating stats over reset.
1. Remove function calls which reset hardware and netdev statistics.
2. Do not rollover statistics in ice_stat_update40 during reset.
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 1229b33973 ("ice: Add low latency Tx timestamp read") refactored
PTP timestamping logic to use a threaded IRQ instead of a separate kthread.
This implementation introduced ice_misc_intr_thread_fn and redefined the
ice_ptp_process_ts function interface to return a value of whether or not
the timestamp processing was complete.
ice_misc_intr_thread_fn would take the return value from ice_ptp_process_ts
and convert it into either IRQ_HANDLED if there were no more timestamps to
be processed, or IRQ_WAKE_THREAD if the thread should continue processing.
This is not correct, as the kernel does not re-schedule threaded IRQ
functions automatically. IRQ_WAKE_THREAD can only be used by the main IRQ
function.
This results in the ice_ptp_process_ts function (and in turn the
ice_ptp_tx_tstamp function) from only being called exactly once per
interrupt.
If an application sends a burst of Tx timestamps without waiting for a
response, the interrupt will trigger for the first timestamp. However,
later timestamps may not have arrived yet. This can result in dropped or
discarded timestamps. Worse, on E822 hardware this results in the interrupt
logic getting stuck such that no future interrupts will be triggered. The
result is complete loss of Tx timestamp functionality.
Fix this by modifying the ice_misc_intr_thread_fn to perform its own
polling of the ice_ptp_process_ts function. We sleep for a few microseconds
between attempts to avoid wasting significant CPU time. The value was
chosen to allow time for the Tx timestamps to complete without wasting so
much time that we overrun application wait budgets in the worst case.
The ice_ptp_process_ts function also currently returns false in the event
that the Tx tracker is not initialized. This would result in the threaded
IRQ handler never exiting if it gets started while the tracker is not
initialized.
Fix the function to appropriately return true when the tracker is not
initialized.
Note that this will not reproduce with default ptp4l behavior, as the
program always synchronously waits for a timestamp response before sending
another timestamp request.
Reported-by: Siddaraju DH <siddaraju.dh@intel.com>
Fixes: 1229b33973 ("ice: Add low latency Tx timestamp read")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20221118222729.1565317-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ADQ, DCB might interfere with Custom Tx Scheduler changes that user
might introduce using devlink-rate API.
Check if ADQ, DCB is active, when user tries to change any setting
in exported Tx scheduler tree. If any of those are active block the user
from doing so, and log an appropriate message.
Remove the exported hierarchy if user enable ADQ or DCB.
Prevent ADQ or DCB from getting configured if user already made some
changes using devlink-rate API.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove ndo_get_devlink_port which is no longer used alongside with the
implementations in drivers.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Benefit from the previously implemented tracking of netdev events in
devlink code and instead of calling devlink_port_type_eth_set() and
devlink_port_type_clear() to set devlink port type and link to related
netdev, use SET_NETDEV_DEVLINK_PORT() macro to assign devlink_port
pointer to netdevice which is about to be registered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch uses TC skbedit queue_mapping action to support
forwarding packets to a device queue. Such filters with action
forward to queue will be the highest priority switch filter in
HW.
Example:
$ tc filter add dev ens4f0 protocol ip ingress flower\
dst_ip 192.168.1.12 ip_proto tcp dst_port 5001\
action skbedit queue_mapping 5 skip_sw
The above command adds an ingress filter, incoming packets
qualifying the match will be accepted into queue 5. The queue
number is in decimal format.
Refactored ice_add_tc_flower_adv_fltr() to consolidate code with
action FWD_TO_VSI and FWD_TO QUEUE.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that netdevice is registered/unregistered while devlink port
is registered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
E810 products can support low latency Tx timestamp register read.
This requires usage of threaded IRQ instead of kthread to reduce the
kthread start latency (spikes up to 20 ms).
Add a check for the device capability and use the new method if
supported.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220916201728.241510-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a reset on ice driver with link-down-on-close flag on
interface would always stay down. Fix this by moving a check of this
flag to ice_stop() that is called only when user wants to bring
interface down.
Fixes: ab4ab73fc1 ("ice: Add ethtool private flag to make forcing link down optional")
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Petr Oros <poros@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After lowering number of tx queues the warning appears:
"Number of in use tx queues changed invalidating tc mappings. Priority
traffic classification disabled!"
Example command to reproduce:
ethtool -L enp24s0f0 tx 36 rx 36
Fix this by setting correct tc mapping before setting real number of
queues on netdev.
Fixes: 0754d65bd4 ("ice: Add infrastructure for mqprio support via ndo_setup_tc")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver currently takes an all or nothing approach for device MSI-X
vectors. Meaning if it does not get its full allocation, it will fail and
not load. There is no reason it can't work with a reduced number of MSI-X
vectors. Take a similar approach as commit 741106f7bd ("ice: Improve
MSI-X fallback logic") and, instead, adjust the MSI-X request to make use
of what is available.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Petr Oros <poros@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
pf->avail_txqs was allocated using bitmap_zalloc, bitmap_free should be
used to free this memory.
Fixes: 78b5713ac1 ("ice: Alloc queue management bitmaps and arrays dynamically")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix leak, when user changes ring parameters.
During reallocation of RX buffers, new DMA mappings are created for
those buffers. New buffers with different RX ring count should
substitute older ones, but those buffers were freed in ice_vsi_cfg_rxq
and reallocated again with ice_alloc_rx_buf. kfree on rx_buf caused
leak of already mapped DMA.
Reallocate ZC with xdp_buf struct, when BPF program loads. Reallocate
back to rx_buf, when BPF program unloads.
If BPF program is loaded/unloaded and XSK pools are created, reallocate
RX queues accordingly in XDP_SETUP_XSK_POOL handler.
Steps for reproduction:
while :
do
for ((i=0; i<=8160; i=i+32))
do
ethtool -G enp130s0f0 rx $i tx $i
sleep 0.5
ethtool -g enp130s0f0
done
done
Fixes: 617f3e1b58 ("ice: xsk: allocate separate memory for XDP SW ring")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Chandan <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-18 (ice)
This series contains updates to ice driver only.
Jesse and Anatolii add support for controlling FCS/CRC stripping via
ethtool.
Anirudh allows for 100M speeds on devices which support it.
Sylwester removes ucast_shared field and the associated dead code related
to it.
Mikael removes non-inclusive language from the driver.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: remove non-inclusive language
ice: Remove ucast_shared
ice: Allow 100M speeds for some devices
ice: Implement FCS/CRC and VLAN stripping co-existence policy
ice: Implement control of FCS/CRC stripping
====================
Link: https://lore.kernel.org/r/20220818155207.996297-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ice driver allocates per cpu XDP queues so that redirect path can safely
use smp_processor_id() as an index to the array. At the same time
though, XDP rings are used to pick NAPI context to call napi_schedule()
or set NAPIF_STATE_MISSED. When user reduces queue count, say to 8, and
num_possible_cpus() of underlying platform is 44, then this means queue
vectors with correlated NAPI contexts will carry several XDP queues.
This in turn can result in a broken behavior where NAPI context of
interest will never be scheduled and AF_XDP socket will not process any
traffic.
To fix this, let us change the way how XDP rings are assigned to Rx
rings and use this information later on when setting
ice_tx_ring::xsk_pool pointer. For each Rx ring, grab the associated
queue vector and walk through Tx ring's linked list. Once we stumble
upon XDP ring in it, assign this ring to ice_rx_ring::xdp_ring.
Previous [0] approach of fixing this issue was for txonly scenario
because of the described grouping of XDP rings across queue vectors. So,
relying on Rx ring meant that NAPI context could be scheduled with a
queue vector without XDP ring with associated XSK pool.
[0]: https://lore.kernel.org/netdev/20220707161128.54215-1-maciej.fijalkowski@intel.com/
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Fixes: 22bf877e52 ("ice: introduce XDP_TX fallback path")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove ucast_shared as it was always true. Remove the code depending on
ucast_shared from ice_add_mac and ice_remove_mac.
Remove ice_find_ucast_rule_entry function as it was only
used when ucast_shared was set to false.
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make sure that only the valid combinations of FCS/CRC stripping and
VLAN stripping offloads are allowed.
You cannot have FCS/CRC stripping disabled while VLAN stripping is
enabled - this breaks the correctness of the FCS/CRC.
If administrator tries to enable VLAN stripping when FCS/CRC stripping is
disabled, the request should be rejected.
If administrator tries to disable FCS/CRC stripping when VLAN stripping
is enabled, the request should be rejected if VLANs are configured. If
there is no VLAN configured, then both FCS/CRC and VLAN stripping should
be disabled.
Testing Hints:
The default settings after driver load are:
- VLAN C-Tag offloads are enabled
- VLAN S-Tag offloads are disabled
- FCS/CRC stripping is enabled
Restore the default settings before each test with the command:
ethtool -K eth0 rx-fcs off rxvlan on txvlan on rx-vlan-stag-hw-parse off
tx-vlan-stag-hw-insert off
Test 1:
Disable FCS/CRC and VLAN stripping:
ethtool -K eth0 rx-fcs on rxvlan off
Try to enable VLAN stripping:
ethtool -K eth0 rxvlan on
Expected: VLAN stripping request is rejected
Test 2:
Try to disable FCS/CRC stripping:
ethtool -K eth0 rx-fcs on
Expected: VLAN stripping is also disabled, as there are no VLAN
configured
Test 3:
Add a VLAN:
ip link add link eth0 eth0.42 type vlan id 42
ip link set eth0 up
Try to disable FCS/CRC stripping:
ethtool -K eth0 rx-fcs on
Expected: FCS/CRC stripping request is rejected
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver can allow the user to configure whether the CRC aka the FCS
(Frame Check Sequence) is DMA'd to the host as part of the receive
buffer. The driver usually wants this feature disabled so that the
hardware checks the FCS and strips it in order to save PCI bandwidth.
Control the reception of FCS to the host using the command:
ethtool -K eth0 rx-fcs <on|off>
The default shown in ethtool -k eth0 | grep fcs; should be "off", as the
hardware will drop any frame with a bad checksum, and DMA of the
checksum is useless overhead especially for small packets.
Testing Hints:
test the FCS/CRC arrives with received packets using
tcpdump -nnpi eth0 -xxxx
and it should show crc data as the last 4 bytes of the packet. Can also
use wireshark to turn on CRC checking and check the data is correct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Co-developed-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When at least two interfaces are bonded and a bridge is enabled on the
bond, an error can occur when the bridge is removed and re-added. The
reason for the error is because promiscuous mode was not fully cleared from
the VLAN VSI in the hardware. With this change, promiscuous mode is
properly removed when the bridge disconnects from bonding.
[ 1033.676359] bond1: link status definitely down for interface enp95s0f0, disabling it
[ 1033.676366] bond1: making interface enp175s0f0 the new active one
[ 1033.676369] device enp95s0f0 left promiscuous mode
[ 1033.676522] device enp175s0f0 entered promiscuous mode
[ 1033.676901] ice 0000:af:00.0 enp175s0f0: Error setting Multicast promiscuous mode on VSI 6
[ 1041.795662] ice 0000:af:00.0 enp175s0f0: Error setting Multicast promiscuous mode on VSI 6
[ 1041.944826] bond1: link status definitely down for interface enp175s0f0, disabling it
[ 1041.944874] device enp175s0f0 left promiscuous mode
[ 1041.944918] bond1: now running without any active interface!
Fixes: c31af68a1b ("ice: Add outer_vlan_ops and VSI specific VLAN ops implementations")
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Link: https://lore.kernel.org/all/CAK8fFZ7m-KR57M_rYX6xZN39K89O=LGooYkKsu6HKt0Bs+x6xQ@mail.gmail.com/
Tested-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Tested-by: Igor Raits <igor@gooddata.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
vsi->current_netdev_flags is used store the current net device
flags, not the active netdevice features. So it should use
vsi->netdev->featurs, rather than vsi->current_netdev_flags
to check NETIF_F_HW_VLAN_CTAG_FILTER.
Fixes: 1babaf77f4 ("ice: Advertise 802.1ad VLAN filtering and offloads for PF netdev")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-07-28
This series contains updates to ice driver only.
Michal allows for VF true promiscuous mode to be set for multiple VFs
and adds clearing of promiscuous filters when VF trust is removed.
Maciej refactors ice_set_features() to track/check changed features
instead of constantly checking against netdev features and adds support for
NETIF_F_LOOPBACK.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: allow toggling loopback mode via ndo_set_features callback
ice: compress branches in ice_set_features()
ice: Fix promiscuous mode not turning off
ice: Introduce enabling promiscuous mode on multiple VF's
====================
Link: https://lore.kernel.org/r/20220728195538.3391360-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for NETIF_F_LOOPBACK. This feature can be set via:
$ ethtool -K eth0 loopback <on|off>
Feature can be useful for local data path tests.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of rather verbose comparison of current netdev->features bits vs
the incoming ones from user, let us compress them by a helper features
set that will be the result of netdev->features XOR features. This way,
current, extensive branches:
if (features & NETIF_F_BIT && !(netdev->features & NETIF_F_BIT))
set_feature(true);
else if (!(features & NETIF_F_BIT) && netdev->features & NETIF_F_BIT)
set_feature(false);
can become:
netdev_features_t changed = netdev->features ^ features;
if (changed & NETIF_F_BIT)
set_feature(!!(features & NETIF_F_BIT));
This is nothing new as currently several other drivers use this
approach, which I find much more convenient.
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In current implementation default VSI switch filter is only able to
forward traffic to a single VSI. This limits promiscuous mode with
private flag 'vf-true-promisc-support' to a single VF. Enabling it on
the second VF won't work. Also allmulticast support doesn't seem to be
properly implemented when vf-true-promisc-support is true.
Use standard ice_add_rule_internal() function that already implements
forwarding to multiple VSI's instead of constructing AQ call manually.
Add switch filter for allmulticast mode when vf-true-promisc-support is
enabled. The same filter is added regardless of the flag - it doesn't
matter for this case.
Remove unnecessary fields in switch structure. From now on book keeping
will be done by ice_add_rule_internal().
Refactor unnecessarily passed function arguments.
To test:
1) Create 2 VM's, and two VF's. Attach VF's to VM's.
2) Enable promiscuous mode on both of them and check if
traffic is seen on both of them.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently loopback test is failiing due to the error returned from
ice_vsi_vlan_setup(). Skip calling it when preparing loopback VSI.
Fixes: 0e674aeb0b ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver currently does not allow two VSIs in the same PF domain
to have the same unicast MAC address. This is incorrect in the sense
that a policy decision is being made in the driver when it must be
left to the user. This approach was causing issues when rebooting
the system with VFs spawned not being able to change their MAC addresses.
Such errors were present in dmesg:
[ 7921.068237] ice 0000:b6:00.2 ens2f2: Unicast MAC 6a:0d:e4:70:ca:d1 already
exists on this PF. Preventing setting VF 7 unicast MAC address to 6a:0d:e4:70:ca:d1
Fix that by removing this restriction. Doing this also allows
us to remove some additional code that's checking if a unicast MAC
filter already exists.
Fixes: 47ebc7b024 ("ice: Check if unicast MAC exists before setting VF MAC")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After commit 62b36c3ea6 ("PCI/AER: Remove
pci_cleanup_aer_uncorrect_error_status() calls"), calls to
pci_cleanup_aer_uncorrect_error_status() have already been removed. But in
commit 5995b6d0c6 ("ice: Implement pci_error_handler ops")
pci_cleanup_aer_uncorrect_error_status was used again, so remove it in
this patch.
Signed-off-by: Zhuo Chen <chenzhuo.1@bytedance.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Sen Wang <wangsen.harry@bytedance.com>
Cc: Wenliang Wang <wangwenliang.1995@bytedance.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver currently presumes that the record data in the PLDM header
of the firmware image will match the device ID of the running device.
This is true for E810 devices. It appears that for E822 devices that
this is not guaranteed to be true.
Fix this by adding a check for the generic E822 device.
Fixes: d69ea414c9 ("ice: implement device flash update via devlink")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VLAN filtering features, that is C-Tag and S-Tag, in DVM mode must be
both enabled or disabled.
In case of turning off/on only one of the features, another feature must
be turned off/on automatically with issuing an appropriate message to
the kernel log.
Fixes: 1babaf77f4 ("ice: Advertise 802.1ad VLAN filtering and offloads for PF netdev")
Signed-off-by: Roman Storozhenko <roman.storozhenko@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The hardware statistics counters are not cleared during resets so the
drivers first access is to initialize the baseline and then subsequent
reads are for reporting the counters. The statistics counters are read
during the watchdog subtask when the interface is up. If the baseline
is not initialized before the interface is up, then there can be a brief
window in which some traffic can be transmitted/received before the
initial baseline reading takes place.
Directly initialize ethtool statistics in driver open so the baseline will
be initialized when the interface is up, and any dropped packets
incremented before the interface is up won't be reported.
Fixes: 28dc1b86f8 ("ice: ignore dropped packets during init")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add extack support to .ndo_fdb_del in netdevice.h and
all related methods.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function ice_plug_aux_dev() assigns pf->adev field too early prior
aux device initialization and on other side ice_unplug_aux_dev()
starts aux device deinit and at the end assigns NULL to pf->adev.
This is wrong because pf->adev should always be non-NULL only when
aux device is fully initialized and ready. This wrong order causes
a crash when ice_send_event_to_aux() call occurs because that function
depends on non-NULL value of pf->adev and does not assume that
aux device is half-initialized or half-destroyed.
After order correction the race window is tiny but it is still there,
as Leon mentioned and manipulation with pf->adev needs to be protected
by mutex.
Fix (un-)plugging functions so pf->adev field is set after aux device
init and prior aux device destroy and protect pf->adev assignment by
new mutex. This mutex is also held during ice_send_event_to_aux()
call to ensure that aux device is valid during that call.
Note that device lock used ice_send_event_to_aux() needs to be kept
to avoid race with aux drv unload.
Reproducer:
cycle=1
while :;do
echo "#### Cycle: $cycle"
ip link set ens7f0 mtu 9000
ip link add bond0 type bond mode 1 miimon 100
ip link set bond0 up
ifenslave bond0 ens7f0
ip link set bond0 mtu 9000
ethtool -L ens7f0 combined 1
ip link del bond0
ip link set ens7f0 mtu 1500
sleep 1
let cycle++
done
In short when the device is added/removed to/from bond the aux device
is unplugged/plugged. When MTU of the device is changed an event is
sent to aux device asynchronously. This can race with (un)plugging
operation and because pf->adev is set too early (plug) or too late
(unplug) the function ice_send_event_to_aux() can touch uninitialized
or destroyed fields. In the case of crash below pf->adev->dev.mutex.
Crash:
[ 53.372066] bond0: (slave ens7f0): making interface the new active one
[ 53.378622] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 53.386294] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[ 53.549104] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 54.118906] ice 0000:ca:00.0 ens7f0: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.233374] ice 0000:ca:00.1 ens7f1: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.248204] bond0: (slave ens7f0): Releasing backup interface
[ 54.253955] bond0: (slave ens7f1): making interface the new active one
[ 54.274875] bond0: (slave ens7f1): Releasing backup interface
[ 54.289153] bond0 (unregistering): Released all slaves
[ 55.383179] MII link monitoring set to 100 ms
[ 55.398696] bond0: (slave ens7f0): making interface the new active one
[ 55.405241] BUG: kernel NULL pointer dereference, address: 0000000000000080
[ 55.405289] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 55.412198] #PF: supervisor write access in kernel mode
[ 55.412200] #PF: error_code(0x0002) - not-present page
[ 55.412201] PGD 25d2ad067 P4D 0
[ 55.412204] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 55.412207] CPU: 0 PID: 403 Comm: kworker/0:2 Kdump: loaded Tainted: G S
5.17.0-13579-g57f2d6540f03 #1
[ 55.429094] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 55.430224] Hardware name: Dell Inc. PowerEdge R750/06V45N, BIOS 1.4.4 10/07/
2021
[ 55.430226] Workqueue: ice ice_service_task [ice]
[ 55.468169] RIP: 0010:mutex_unlock+0x10/0x20
[ 55.472439] Code: 0f b1 13 74 96 eb e0 4c 89 ee eb d8 e8 79 54 ff ff 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 65 48 8b 04 25 40 ef 01 00 31 d2 <f0> 48 0f b1 17 75 01 c3 e9 e3 fe ff ff 0f 1f 00 0f 1f 44 00 00 48
[ 55.491186] RSP: 0018:ff4454230d7d7e28 EFLAGS: 00010246
[ 55.496413] RAX: ff1a79b208b08000 RBX: ff1a79b2182e8880 RCX: 0000000000000001
[ 55.503545] RDX: 0000000000000000 RSI: ff4454230d7d7db0 RDI: 0000000000000080
[ 55.510678] RBP: ff1a79d1c7e48b68 R08: ff4454230d7d7db0 R09: 0000000000000041
[ 55.517812] R10: 00000000000000a5 R11: 00000000000006e6 R12: ff1a79d1c7e48bc0
[ 55.524945] R13: 0000000000000000 R14: ff1a79d0ffc305c0 R15: 0000000000000000
[ 55.532076] FS: 0000000000000000(0000) GS:ff1a79d0ffc00000(0000) knlGS:0000000000000000
[ 55.540163] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 55.545908] CR2: 0000000000000080 CR3: 00000003487ae003 CR4: 0000000000771ef0
[ 55.553041] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 55.560173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 55.567305] PKRU: 55555554
[ 55.570018] Call Trace:
[ 55.572474] <TASK>
[ 55.574579] ice_service_task+0xaab/0xef0 [ice]
[ 55.579130] process_one_work+0x1c5/0x390
[ 55.583141] ? process_one_work+0x390/0x390
[ 55.587326] worker_thread+0x30/0x360
[ 55.590994] ? process_one_work+0x390/0x390
[ 55.595180] kthread+0xe6/0x110
[ 55.598325] ? kthread_complete_and_exit+0x20/0x20
[ 55.603116] ret_from_fork+0x1f/0x30
[ 55.606698] </TASK>
Fixes: f9f5301e7e ("ice: Register auxiliary device to provide RDMA")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Switch id should be the same for each netdevice on a driver.
The id must be unique between devices on the same system, but
does not need to be unique between devices on different systems.
The switch id is used to locate ports on a switch and to know if
aggregated ports belong to the same switch.
To meet this requirements, use pci_get_dsn as switch id value, as
this is unique value for each devices on the same system.
Implementing switch id is needed by automatic tools for kubernetes.
Set switch id by setting devlink port attribiutes and calling
devlink_port_attrs_set while creating pf (for uplink) and vf
(for representator) devlink port.
To get switch id (in switchdev mode):
cat /sys/class/net/$PF0/phys_switch_id
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We need to wait 5 s for EMP reset after firmware flash. Code was extracted
from OOT driver (ice v1.8.3 downloaded from sourceforge). Without this
wait, fw_activate let card in inconsistent state and recoverable only
by second flash/activate. Flash was tested on these fw's:
From -> To
3.00 -> 3.10/3.20
3.10 -> 3.00/3.20
3.20 -> 3.00/3.10
Reproducer:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
71: ens7f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
dmesg after flash:
[ 55.120788] ice: Copyright (c) 2018, Intel Corporation.
[ 55.274734] ice 0000:ca:00.0: Get PHY capabilities failed status = -5, continuing anyway
[ 55.569797] ice 0000:ca:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.28.0
[ 55.603629] ice 0000:ca:00.0: Get PHY capability failed.
[ 55.608951] ice 0000:ca:00.0: ice_init_nvm_phy_type failed: -5
[ 55.647348] ice 0000:ca:00.0: PTP init successful
[ 55.675536] ice 0000:ca:00.0: DCB is enabled in the hardware, max number of TCs supported on this port are 8
[ 55.685365] ice 0000:ca:00.0: FW LLDP is disabled, DCBx/LLDP in SW mode.
[ 55.692179] ice 0000:ca:00.0: Commit DCB Configuration to the hardware
[ 55.701382] ice 0000:ca:00.0: 126.024 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x8 link at 0000:c9:02.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
Reboot doesn’t help, only second flash/activate with OOT or patched
driver put card back in consistent state.
After patch:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
19: ens7f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
Fixes: 399e27dbbd ("ice: support immediate firmware activation via devlink reload")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to add mpls+tso support.
I don't have ice hardware available to test myself, but I just implemented
this feature in i40e and thought it might be useful to implement for ice
while this is fresh in my brain.
Hoping some one at intel will be able to test this on my behalf.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The CI testing bots triggered the following splat:
[ 718.203054] BUG: KASAN: use-after-free in free_irq_cpu_rmap+0x53/0x80
[ 718.206349] Read of size 4 at addr ffff8881bd127e00 by task sh/20834
[ 718.212852] CPU: 28 PID: 20834 Comm: sh Kdump: loaded Tainted: G S W IOE 5.17.0-rc8_nextqueue-devqueue-02643-g23f3121aca93 #1
[ 718.219695] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0012.070720200218 07/07/2020
[ 718.223418] Call Trace:
[ 718.227139]
[ 718.230783] dump_stack_lvl+0x33/0x42
[ 718.234431] print_address_description.constprop.9+0x21/0x170
[ 718.238177] ? free_irq_cpu_rmap+0x53/0x80
[ 718.241885] ? free_irq_cpu_rmap+0x53/0x80
[ 718.245539] kasan_report.cold.18+0x7f/0x11b
[ 718.249197] ? free_irq_cpu_rmap+0x53/0x80
[ 718.252852] free_irq_cpu_rmap+0x53/0x80
[ 718.256471] ice_free_cpu_rx_rmap.part.11+0x37/0x50 [ice]
[ 718.260174] ice_remove_arfs+0x5f/0x70 [ice]
[ 718.263810] ice_rebuild_arfs+0x3b/0x70 [ice]
[ 718.267419] ice_rebuild+0x39c/0xb60 [ice]
[ 718.270974] ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 718.274472] ? ice_init_phy_user_cfg+0x360/0x360 [ice]
[ 718.278033] ? delay_tsc+0x4a/0xb0
[ 718.281513] ? preempt_count_sub+0x14/0xc0
[ 718.284984] ? delay_tsc+0x8f/0xb0
[ 718.288463] ice_do_reset+0x92/0xf0 [ice]
[ 718.292014] ice_pci_err_resume+0x91/0xf0 [ice]
[ 718.295561] pci_reset_function+0x53/0x80
<...>
[ 718.393035] Allocated by task 690:
[ 718.433497] Freed by task 20834:
[ 718.495688] Last potentially related work creation:
[ 718.568966] The buggy address belongs to the object at ffff8881bd127e00
which belongs to the cache kmalloc-96 of size 96
[ 718.574085] The buggy address is located 0 bytes inside of
96-byte region [ffff8881bd127e00, ffff8881bd127e60)
[ 718.579265] The buggy address belongs to the page:
[ 718.598905] Memory state around the buggy address:
[ 718.601809] ffff8881bd127d00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ 718.604796] ffff8881bd127d80: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
[ 718.607794] >ffff8881bd127e00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ 718.610811] ^
[ 718.613819] ffff8881bd127e80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
[ 718.617107] ffff8881bd127f00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
This is due to that free_irq_cpu_rmap() is always being called
*after* (devm_)free_irq() and thus it tries to work with IRQ descs
already freed. For example, on device reset the driver frees the
rmap right before allocating a new one (the splat above).
Make rmap creation and freeing function symmetrical with
{request,free}_irq() calls i.e. do that on ifup/ifdown instead
of device probe/remove/resume. These operations can be performed
independently from the actual device aRFS configuration.
Also, make sure ice_vsi_free_irq() clears IRQ affinity notifiers
only when aRFS is disabled -- otherwise, CPU rmap sets and clears
its own and they must not be touched manually.
Fixes: 28bf26724f ("ice: Implement aRFS")
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when XDP rings are created, each descriptor gets its DD bit
set, which turns out to be the wrong approach as it can lead to a
situation where more descriptors get cleaned than it was supposed to,
e.g. when AF_XDP busy poll is run with a large batch size. In this
situation, the driver would request for more buffers than it is able to
handle.
Fix this by not setting the DD bits in ice_xdp_alloc_setup_rings(). They
should be initialized to zero instead.
Fixes: 9610bd988d ("ice: optimize XDP_TX workloads")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Unfortunately, the ice driver doesn't respect the RCU critical section that
XSK wakeup is surrounded with. To fix this, add synchronize_rcu() calls to
paths that destroy resources that might be in use.
This was addressed in other AF_XDP ZC enabled drivers, for reference see
for example commit b3873a5be7 ("net/i40e: Fix concurrency issues
between config flow and XSK")
Fixes: efc2214b60 ("ice: Add support for XDP")
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Handling of all-multicast flag and associated multicast promiscuous
mode is broken in ice driver. When an user switches allmulticast
flag on or off the driver checks whether any VLANs are configured
over the interface (except default VLAN 0).
If any extra VLANs are registered it enables multicast promiscuous
mode for all these VLANs (including default VLAN 0) using
ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all
multicast packets tagged with known VLAN ID or untagged are received
and multicast packets tagged with unknown VLAN ID ignored.
If no extra VLANs are registered (so only VLAN 0 exists) it enables
multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC
look-up type. In this situation any multicast packets including
tagged ones are received.
The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:
ice_vsi_sync_fltr() {
...
if (changed_flags & IFF_ALLMULTI) {
if (netdev->flags & IFF_ALLMULTI) {
if (vsi->num_vlans > 1)
ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
} else {
if (vsi->num_vlans > 1)
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
}
}
...
}
The code above depends on value vsi->num_vlan that specifies number
of VLANs configured over the interface (including VLAN 0) and
this is problem because that value is modified in NDO callbacks
ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().
Scenario 1:
1. ip link set ens7f0 allmulticast on
2. ip link add vlan10 link ens7f0 type vlan id 10
3. ip link set ens7f0 allmulticast off
4. ip link set ens7f0 allmulticast on
[1] In this scenario IFF_ALLMULTI is enabled and the driver calls
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs
multicast promisc rule with non-VLAN look-up type.
[2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
[3] Command switches IFF_ALLMULTI off and the driver calls
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this
call is effectively NOP because it looks for multicast promisc
rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such
rules exist. So the all-multicast remains enabled silently
in hardware.
[4] Command tries to switch IFF_ALLMULTI on and the driver calls
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call
fails (-EEXIST) because non-VLAN multicast promisc rule already
exists.
Scenario 2:
1. ip link add vlan10 link ens7f0 type vlan id 10
2. ip link set ens7f0 allmulticast on
3. ip link add vlan20 link ens7f0 type vlan id 20
4. ip link del vlan10 ; ip link del vlan20
5. ip link set ens7f0 allmulticast off
[1] VLAN with ID 10 is added and vsi->num_vlan==2
[2] Command switches IFF_ALLMULTI on and driver installs multicast
promisc rules with VLAN look-up type for VLAN 0 and 10
[3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast
promisc rules is added for this new VLAN so the interface does
not receive MC packets from VLAN 20
[4] Both VLANs are removed but multicast rule for VLAN 10 remains
installed so interface receives multicast packets from VLAN 10
[5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1
the driver tries to remove multicast promisc rule for VLAN 0
with non-VLAN look-up that does not exist.
All-multicast looks disabled from user point of view but it
is partially enabled in HW (interface receives all multicast
packets either untagged or tagged with VLAN ID 10)
To resolve these issues the patch introduces these changes:
1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and
ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed
and IFF_ALLMULTI is enabled an appropriate multicast promisc
rule for that VLAN ID is added/removed.
2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added
so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_VLAN_PROMISC_BITS.
3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed
so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_PROMISC_BITS.
4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY
bit protection to avoid races with ice_vsi_sync_fltr() that runs
in ice_service_task() context.
5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
6. Error messages added to ice_fltr_*_vsi_promisc() helper functions
to avoid them in their callers
7. Small improvements to increase readability
Fixes: 5eda8afd6b ("ice: Add support for PF/VF promiscuous mode")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2ccc1c1ccc ("ice: Remove excess error variables") merged
the usage of 'status' and 'err' variables into single one in
function ice_set_mac_address(). Unfortunately this causes
a regression when call of ice_fltr_add_mac() returns -EEXIST because
this return value does not indicate an error in this case but
value of 'err' remains to be -EEXIST till the end of the function
and is returned to caller.
Prior mentioned commit this does not happen because return value of
ice_fltr_add_mac() was stored to 'status' variable first and
if it was -EEXIST then 'err' remains to be zero.
Fix the problem by reset 'err' to zero when ice_fltr_add_mac()
returns -EEXIST.
Fixes: 2ccc1c1ccc ("ice: Remove excess error variables")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a kernel BUG splat on processing aux critical error
interrupts in ice_misc_intr():
[ 2100.917085] BUG: scheduling while atomic: swapper/15/0/0x00010000
...
[ 2101.060770] Call Trace:
[ 2101.063229] <IRQ>
[ 2101.065252] dump_stack+0x41/0x60
[ 2101.068587] __schedule_bug.cold.100+0x4c/0x58
[ 2101.073060] __schedule+0x6a4/0x830
[ 2101.076570] schedule+0x35/0xa0
[ 2101.079727] schedule_preempt_disabled+0xa/0x10
[ 2101.084284] __mutex_lock.isra.7+0x310/0x420
[ 2101.088580] ? ice_misc_intr+0x201/0x2e0 [ice]
[ 2101.093078] ice_send_event_to_aux+0x25/0x70 [ice]
[ 2101.097921] ice_misc_intr+0x220/0x2e0 [ice]
[ 2101.102232] __handle_irq_event_percpu+0x40/0x180
[ 2101.106965] handle_irq_event_percpu+0x30/0x80
[ 2101.111434] handle_irq_event+0x36/0x53
[ 2101.115292] handle_edge_irq+0x82/0x190
[ 2101.119148] handle_irq+0x1c/0x30
[ 2101.122480] do_IRQ+0x49/0xd0
[ 2101.125465] common_interrupt+0xf/0xf
[ 2101.129146] </IRQ>
...
As Andrew correctly mentioned previously[0], the following call
ladder happens:
ice_misc_intr() <- hardirq
ice_send_event_to_aux()
device_lock()
mutex_lock()
might_sleep()
might_resched() <- oops
Add a new PF state bit which indicates that an aux critical error
occurred and serve it in ice_service_task() in process context.
The new ice_pf::oicr_err_reg is read-write in both hardirq and
process contexts, but only 3 bits of non-critical data probably
aren't worth explicit synchronizing (and they're even in the same
byte [31:24]).
[0] https://lore.kernel.org/all/YeSRUVmrdmlUXHDn@lunn.ch
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently fdir_fltr_lock is accessed in ice_vsi_release_all() function
after it is destroyed. Instead destroy mutex after ice_vsi_release_all.
Fixes: 40319796b7 ("ice: Add flow director support for channel mode")
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is possible to do NULL pointer dereference in routine that updates
Tx ring stats. Currently only stats and bytes are updated when ring
pointer is valid, but later on ring is accessed to propagate gathered Tx
stats onto VSI stats.
Change the existing logic to move to next ring when ring is NULL.
Fixes: e72bba2135 ("ice: split ice_ring onto Tx/Rx separate structs")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_reset_vf function performs actions which must be taken only
while holding the VF configuration lock. Some flows already acquired the
lock, while other flows must acquire it just for the reset function. Add
the ICE_VF_RESET_LOCK flag to the function so that it can handle taking
and releasing the lock instead at the appropriate scope.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_reset_vf function takes a boolean parameter which indicates
whether or not the reset is due to a VFLR event.
This is somewhat confusing to read because readers must interpret what
"true" and "false" mean when seeing a line of code like
"ice_reset_vf(vf, false)".
We will want to add another toggle to the ice_reset_vf in a following
change. To avoid proliferating many arguments, convert this function to
take flags instead. ICE_VF_RESET_VFLR will indicate if this is a VFLR
reset. A value of 0 indicates no flags.
One could argue that "ice_reset_vf(vf, 0)" is no more readable than
"ice_reset_vf(vf, false)".. However, this type of flags interface is
somewhat common and using 0 to mean "no flags" makes sense in this
context. We could bother to add a define for "ICE_VF_RESET_PLAIN" or
something similar, but this can be confusing since its not an actual bit
flag.
This paves the way to add another flag to the function in a following
change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_reset_all_vfs function takes a parameter to handle whether its
operating after a VFLR event or not. This is not necessary as every
caller always passes true. Simplify the interface by removing the
parameter.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ICE_MAX_VF_COUNT field is defined in ice_sriov.h. This count is true
for SR-IOV but will not be true for all VF implementations, such as when
the ice driver supports Scalable IOV.
Rename this definition to clearly indicate ICE_MAX_SRIOV_VFS.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Several headers in the ice driver include ice.h even though they are
themselves included by that header. The most notable of these is
ice_common.h, but several other headers also do this.
Such a recursive inclusion is problematic as it forces headers to be
included in a strict order, otherwise compilation errors can result. The
circular inclusions do not trigger an endless loop due to standard
header inclusion guards, however other errors can occur.
For example, ice_flow.h defines ice_rss_hash_cfg, which is used by
ice_sriov.h as part of the definition of ice_vf_hash_ip_ctx.
ice_flow.h includes ice_acl.h, which includes ice_common.h, and which
finally includes ice.h. Since ice.h itself includes ice_sriov.h, this
creates a circular dependency.
The definition in ice_sriov.h requires things from ice_flow.h, but
ice_flow.h itself will lead to trying to load ice_sriov.h as part of its
process for expanding ice.h. The current code avoids this issue by
having an implicit dependency without the include of ice_flow.h.
If we were to fix that so that ice_sriov.h explicitly depends on
ice_flow.h the following pattern would occur:
ice_flow.h -> ice_acl.h -> ice_common.h -> ice.h -> ice_sriov.h
At this point, during the expansion of, the header guard for ice_flow.h
is already set, so when ice_sriov.h attempts to load the ice_flow.h
header it is skipped. Then, we go on to begin including the rest of
ice_sriov.h, including structure definitions which depend on
ice_rss_hash_cfg. This produces a compiler warning because
ice_rss_hash_cfg hasn't yet been included. Remember, we're just at the
start of ice_flow.h!
If the order of headers is incorrect (ice_flow.h is not implicitly
loaded first in all files which include ice_sriov.h) then we get the
same failure.
Removing this recursive inclusion requires fixing a few cases where some
headers depended on the header inclusions from ice.h. In addition, a few
other changes are also required.
Most notably, ice_hw_to_dev is implemented as a macro in ice_osdep.h,
which is the likely reason that ice_common.h includes ice.h at all. This
macro implementation requires the full definition of ice_pf in order to
properly compile.
Fix this by moving it to a function declared in ice_main.c, so that we
do not require all files to depend on the layout of the ice_pf
structure.
Note that this change only fixes circular dependencies, but it does not
fully resolve all implicit dependencies where one header may depend on
the inclusion of another. I tried to fix as many of the implicit
dependencies as I noticed, but fixing them all requires a somewhat
tedious analysis of each header and attempting to compile it separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-03-09
This series contains updates to ice driver only.
Martyna implements switchdev filtering on inner EtherType field for
tunnels.
Marcin adds reporting of slowpath statistics for port representors.
Jonathan Toppins changes a non-fatal link error message from warning to
debug.
Maciej removes unnecessary checks in ice_clean_tx_irq().
Amritha adds support for ADQ to match outer destination MAC for tunnels.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Add support for outer dest MAC for ADQ tunnels
ice: avoid XDP checks in ice_clean_tx_irq()
ice: change "can't set link" message to dbg level
ice: Add slow path offload stats on port representor in switchdev
ice: Add support for inner etype in switchdev
====================
Link: https://lore.kernel.org/r/20220309190315.1380414-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 5dbbbd01cb ("ice: Avoid RTNL lock when re-creating
auxiliary device") changes a process of re-creation of aux device
so ice_plug_aux_dev() is called from ice_service_task() context.
This unfortunately opens a race window that can result in dead-lock
when interface has left LAG and immediately enters LAG again.
Reproducer:
```
#!/bin/sh
ip link add lag0 type bond mode 1 miimon 100
ip link set lag0
for n in {1..10}; do
echo Cycle: $n
ip link set ens7f0 master lag0
sleep 1
ip link set ens7f0 nomaster
done
```
This results in:
[20976.208697] Workqueue: ice ice_service_task [ice]
[20976.213422] Call Trace:
[20976.215871] __schedule+0x2d1/0x830
[20976.219364] schedule+0x35/0xa0
[20976.222510] schedule_preempt_disabled+0xa/0x10
[20976.227043] __mutex_lock.isra.7+0x310/0x420
[20976.235071] enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core]
[20976.251215] ib_enum_roce_netdev+0xa4/0xe0 [ib_core]
[20976.256192] ib_cache_setup_one+0x33/0xa0 [ib_core]
[20976.261079] ib_register_device+0x40d/0x580 [ib_core]
[20976.266139] irdma_ib_register_device+0x129/0x250 [irdma]
[20976.281409] irdma_probe+0x2c1/0x360 [irdma]
[20976.285691] auxiliary_bus_probe+0x45/0x70
[20976.289790] really_probe+0x1f2/0x480
[20976.298509] driver_probe_device+0x49/0xc0
[20976.302609] bus_for_each_drv+0x79/0xc0
[20976.306448] __device_attach+0xdc/0x160
[20976.310286] bus_probe_device+0x9d/0xb0
[20976.314128] device_add+0x43c/0x890
[20976.321287] __auxiliary_device_add+0x43/0x60
[20976.325644] ice_plug_aux_dev+0xb2/0x100 [ice]
[20976.330109] ice_service_task+0xd0c/0xed0 [ice]
[20976.342591] process_one_work+0x1a7/0x360
[20976.350536] worker_thread+0x30/0x390
[20976.358128] kthread+0x10a/0x120
[20976.365547] ret_from_fork+0x1f/0x40
...
[20976.438030] task:ip state:D stack: 0 pid:213658 ppid:213627 flags:0x00004084
[20976.446469] Call Trace:
[20976.448921] __schedule+0x2d1/0x830
[20976.452414] schedule+0x35/0xa0
[20976.455559] schedule_preempt_disabled+0xa/0x10
[20976.460090] __mutex_lock.isra.7+0x310/0x420
[20976.464364] device_del+0x36/0x3c0
[20976.467772] ice_unplug_aux_dev+0x1a/0x40 [ice]
[20976.472313] ice_lag_event_handler+0x2a2/0x520 [ice]
[20976.477288] notifier_call_chain+0x47/0x70
[20976.481386] __netdev_upper_dev_link+0x18b/0x280
[20976.489845] bond_enslave+0xe05/0x1790 [bonding]
[20976.494475] do_setlink+0x336/0xf50
[20976.502517] __rtnl_newlink+0x529/0x8b0
[20976.543441] rtnl_newlink+0x43/0x60
[20976.546934] rtnetlink_rcv_msg+0x2b1/0x360
[20976.559238] netlink_rcv_skb+0x4c/0x120
[20976.563079] netlink_unicast+0x196/0x230
[20976.567005] netlink_sendmsg+0x204/0x3d0
[20976.570930] sock_sendmsg+0x4c/0x50
[20976.574423] ____sys_sendmsg+0x1eb/0x250
[20976.586807] ___sys_sendmsg+0x7c/0xc0
[20976.606353] __sys_sendmsg+0x57/0xa0
[20976.609930] do_syscall_64+0x5b/0x1a0
[20976.613598] entry_SYSCALL_64_after_hwframe+0x65/0xca
1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev()
is called from ice_service_task() context, aux device is created
and associated device->lock is taken.
2. Command 'ip link ... set master...' calls ice's notifier under
RTNL lock and that notifier calls ice_unplug_aux_dev(). That
function tries to take aux device->lock but this is already taken
by ice_plug_aux_dev() in step 1
3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already
taken in step 2
4. Dead-lock
The patch fixes this issue by following changes:
- Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev()
call in ice_service_task()
- The bit is checked in ice_clear_rdma_cap() and only if it is not set
then ice_unplug_aux_dev() is called. If it is set (in other words
plugging of aux device was requested and ice_plug_aux_dev() is
potentially running) then the function only clears the bit
- Once ice_plug_aux_dev() call (in ice_service_task) is finished
the bit ICE_FLAG_PLUG_AUX_DEV is cleared but it is also checked
whether it was already cleared by ice_clear_rdma_cap(). If so then
aux device is unplugged.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Co-developed-by: Petr Oros <poros@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Link: https://lore.kernel.org/r/20220310171641.3863659-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement callbacks to check for stats and fetch port representor stats.
Stats are taken from RX/TX ring corresponding to port representor and show
the number of bytes/packets that were not offloaded.
To see slow path stats run:
ifstat -x cpu_hits -a
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_misc_intr() is an irq handler. It should not sleep.
Use GFP_ATOMIC instead of GFP_KERNEL when allocating some memory.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a bonded interface is destroyed, .ndo_change_mtu can be called
during the tear-down process while the RTNL lock is held. This is a
problem since the auxiliary driver linked to the LAN driver needs to be
notified of the MTU change, and this requires grabbing a device_lock on
the auxiliary_device's dev. Currently this is being attempted in the
same execution context as the call to .ndo_change_mtu which is causing a
dead-lock.
Move the notification of the changed MTU to a separate execution context
(watchdog service task) and eliminate the "before" notification.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver stores VF structures in a simple array which is allocated
once at the time of VF creation. The VF structures are then accessed
from the array by their VF ID. The ID must be between 0 and the number
of allocated VFs.
Multiple threads can access this table:
* .ndo operations such as .ndo_get_vf_cfg or .ndo_set_vf_trust
* interrupts, such as due to messages from the VF using the virtchnl
communication
* processing such as device reset
* commands to add or remove VFs
The current implementation does not keep track of when all threads are
done operating on a VF and can potentially result in use-after-free
issues caused by one thread accessing a VF structure after it has been
released when removing VFs. Some of these are prevented with various
state flags and checks.
In addition, this structure is quite static and does not support a
planned future where virtualization can be more dynamic. As we begin to
look at supporting Scalable IOV with the ice driver (as opposed to just
supporting Single Root IOV), this structure is not sufficient.
In the future, VFs will be able to be added and removed individually and
dynamically.
To allow for this, and to better protect against a whole class of
use-after-free bugs, replace the VF storage with a combination of a hash
table and krefs to reference track all of the accesses to VFs through
the hash table.
A hash table still allows efficient look up of the VF given its ID, but
also allows adding and removing VFs. It does not require contiguous VF
IDs.
The use of krefs allows the cleanup of the VF memory to be delayed until
after all threads have released their reference (by calling ice_put_vf).
To prevent corruption of the hash table, a combination of RCU and the
mutex table_lock are used. Addition and removal from the hash table use
the RCU-aware hash macros. This allows simple read-only look ups that
iterate to locate a single VF can be fast using RCU. Accesses which
modify the hash table, or which can't take RCU because they sleep, will
hold the mutex lock.
By using this design, we have a stronger guarantee that the VF structure
can't be released until after all threads are finished operating on it.
We also pave the way for the more dynamic Scalable IOV implementation in
the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We maintain a number of values for VFs within the ice_pf structure. This
includes the VF table, the number of allocated VFs, the maximum number
of supported SR-IOV VFs, the number of queue pairs per VF, the number of
MSI-X vectors per VF, and a bitmap of the VFs with detected MDD events.
We're about to add a few more variables to this list. Clean this up
first by extracting these members out into a new ice_vfs structure
defined in ice_virtchnl_pf.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_for_each_vf macro is intended to be used to loop over all VFs.
The current implementation relies on an iterator that is the index into
the VF array in the PF structure. This forces all users to perform a
look up themselves.
This abstraction forces a lot of duplicate work on callers and leaks the
interface implementation to the caller. Replace this with an
implementation that includes the VF pointer the primary iterator. This
version simplifies callers which just want to iterate over every VF, as
they no longer need to perform their own lookup.
The "i" iterator value is replaced with a new unsigned int "bkt"
parameter, as this will match the necessary interface for replacing
the VF array with a hash table. For now, the bkt is the VF ID, but in
the future it will simply be the hash bucket index. Document that it
should not be treated as a VF ID.
This change aims to simplify switching from the array to a hash table. I
considered alternative implementations such as an xarray but decided
that the hash table was the simplest and most suitable implementation. I
also looked at methods to hide the bkt iterator entirely, but I couldn't
come up with a feasible solution that worked for hash table iterators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The VSI structure contains a vf_id field used to associate a VSI with a
VF. This is used mainly for ICE_VSI_VF as well as partially for
ICE_VSI_CTRL associated with the VFs.
This API was designed with the idea that VFs are stored in a simple
array that was expected to be static throughout most of the driver's
life.
We plan on refactoring VF storage in a few key ways:
1) converting from a simple static array to a hash table
2) using krefs to track VF references obtained from the hash table
3) use RCU to delay release of VF memory until after all references
are dropped
This is motivated by the goal to ensure that the lifetime of VF
structures is accounted for, and prevent various use-after-free bugs.
With the existing vsi->vf_id, the reference tracking for VFs would
become somewhat convoluted, because each VSI maintains a vf_id field
which will then require performing a look up. This means all these flows
will require reference tracking and proper usage of rcu_read_lock, etc.
We know that the VF VSI will always be backed by a valid VF structure,
because the VSI is created during VF initialization and removed before
the VF is destroyed. Rely on this and store a reference to the VF in the
VSI structure instead of storing a VF ID. This will simplify the usage
and avoid the need to perform lookups on the hash table in the future.
For ICE_VSI_VF, it is expected that vsi->vf is always non-NULL after
ice_vsi_alloc succeeds. Because of this, use WARN_ON when checking if a
vsi->vf pointer is valid when dealing with VF VSIs. This will aid in
debugging code which violates this assumption and avoid more disastrous
panics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new ice_gnss.c file for holding the basic GNSS module functions.
If the device supports GNSS module, call the new ice_gnss_init and
ice_gnss_release functions where appropriate.
Implement basic functionality for reading the data from GNSS module
using TTY device.
Add I2C read AQ command. It is now required for controlling the external
physical connectors via external I2C port expander on E810-T adapters.
Future changes will introduce write functionality.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sudhansu Sekhar Mishra <sudhansu.mishra@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c503e63200 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The status of support for RDMA is currently being tracked with two
separate status flags. This is unnecessary with the current state of
the driver.
Simplify status tracking down to a single flag.
Rename the helper function to denote the RDMA specific status and
universally use the helper function to test the status bit.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a call to re-create the auxiliary device happens in a context that has
already taken the RTNL lock, then the call flow that recreates auxiliary
device can hang if there is another attempt to claim the RTNL lock by the
auxiliary driver.
To avoid this, any call to re-create auxiliary devices that comes from
an source that is holding the RTNL lock (e.g. netdev notifier when
interface exits a bond) should execute in a separate thread. To
accomplish this, add a flag to the PF that will be evaluated in the
service task and dealt with there.
Fixes: f9f5301e7e ("ice: Register auxiliary device to provide RDMA")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver was avoiding offload for IPIP (at least) frames due to
parsing the inner header offsets incorrectly when trying to check
lengths.
This length check works for VXLAN frames but fails on IPIP frames
because skb_transport_offset points to the inner header in IPIP
frames, which meant the subtraction of transport_header from
inner_network_header returns a negative value (-20).
With the code before this patch, everything continued to work, but GSO
was being used to segment, causing throughputs of 1.5Gb/s per thread.
After this patch, throughput is more like 10Gb/s per thread for IPIP
traffic.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-02-09
This series contains updates to ice driver only.
Brett adds support for QinQ. This begins with code refactoring and
re-organization of VLAN configuration functions to allow for
introduction of VSI VLAN ops to enable setting and calling of
respective operations based on device support of single or double
VLANs. Implementations are added for outer VLAN support.
To support QinQ, the device must be set to double VLAN mode (DVM).
In order for this to occur, the DDP package and NVM must also support
DVM. Functions to determine compatibility and properly configure the
device are added as well as setting the proper bits to advertise and
utilize the proper offloads. Support for VIRTCHNL_VF_OFFLOAD_VLAN_V2
is also included to allow for VF to negotiate and utilize this
functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-02-09
We've added 126 non-merge commits during the last 16 day(s) which contain
a total of 201 files changed, 4049 insertions(+), 2215 deletions(-).
The main changes are:
1) Add custom BPF allocator for JITs that pack multiple programs into a huge
page to reduce iTLB pressure, from Song Liu.
2) Add __user tagging support in vmlinux BTF and utilize it from BPF
verifier when generating loads, from Yonghong Song.
3) Add per-socket fast path check guarding from cgroup/BPF overhead when
used by only some sockets, from Pavel Begunkov.
4) Continued libbpf deprecation work of APIs/features and removal of their
usage from samples, selftests, libbpf & bpftool, from Andrii Nakryiko
and various others.
5) Improve BPF instruction set documentation by adding byte swap
instructions and cleaning up load/store section, from Christoph Hellwig.
6) Switch BPF preload infra to light skeleton and remove libbpf dependency
from it, from Alexei Starovoitov.
7) Fix architecture-agnostic macros in libbpf for accessing syscall
arguments from BPF progs for non-x86 architectures,
from Ilya Leoshkevich.
8) Rework port members in struct bpf_sk_lookup and struct bpf_sock to be
of 16-bit field with anonymous zero padding, from Jakub Sitnicki.
9) Add new bpf_copy_from_user_task() helper to read memory from a different
task than current. Add ability to create sleepable BPF iterator progs,
from Kenny Yu.
10) Implement XSK batching for ice's zero-copy driver used by AF_XDP and
utilize TX batching API from XSK buffer pool, from Maciej Fijalkowski.
11) Generate temporary netns names for BPF selftests to avoid naming
collisions, from Hangbin Liu.
12) Implement bpf_core_types_are_compat() with limited recursion for
in-kernel usage, from Matteo Croce.
13) Simplify pahole version detection and finally enable CONFIG_DEBUG_INFO_DWARF5
to be selected with CONFIG_DEBUG_INFO_BTF, from Nathan Chancellor.
14) Misc minor fixes to libbpf and selftests from various folks.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (126 commits)
selftests/bpf: Cover 4-byte load from remote_port in bpf_sk_lookup
bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
libbpf: Fix compilation warning due to mismatched printf format
selftests/bpf: Test BPF_KPROBE_SYSCALL macro
libbpf: Add BPF_KPROBE_SYSCALL macro
libbpf: Fix accessing the first syscall argument on s390
libbpf: Fix accessing the first syscall argument on arm64
libbpf: Allow overriding PT_REGS_PARM1{_CORE}_SYSCALL
selftests/bpf: Skip test_bpf_syscall_macro's syscall_arg1 on arm64 and s390
libbpf: Fix accessing syscall arguments on riscv
libbpf: Fix riscv register names
libbpf: Fix accessing syscall arguments on powerpc
selftests/bpf: Use PT_REGS_SYSCALL_REGS in bpf_syscall_macro
libbpf: Add PT_REGS_SYSCALL_REGS macro
selftests/bpf: Fix an endianness issue in bpf_syscall_macro test
bpf: Fix bpf_prog_pack build HPAGE_PMD_SIZE
bpf: Fix leftover header->pages in sparc and powerpc code.
libbpf: Fix signedness bug in btf_dump_array_data()
selftests/bpf: Do not export subtest as standalone test
bpf, x86_64: Fail gracefully on bpf_jit_binary_pack_finalize failures
...
====================
Link: https://lore.kernel.org/r/20220209210050.8425-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order for the driver to support 802.1ad VLAN filtering and offloads,
it needs to advertise those VLAN features and also support modifying
those VLAN features, so make the necessary changes to
ice_set_netdev_features(). By default, enable CTAG insertion/stripping
and CTAG filtering for both Single and Double VLAN Modes (SVM/DVM).
Also, in DVM, enable STAG filtering by default. This is done by
setting the feature bits in netdev->features. Also, in DVM, support
toggling of STAG insertion/stripping, but don't enable them by
default. This is done by setting the feature bits in
netdev->hw_features.
Since 802.1ad VLAN filtering and offloads are only supported in DVM, make
sure they are not enabled by default and that they cannot be enabled
during runtime, when the device is in SVM.
Add an implementation for the ndo_fix_features() callback. This is
needed since the hardware cannot support multiple VLAN ethertypes for
VLAN insertion/stripping simultaneously and all supported VLAN filtering
must either be enabled or disabled together.
Disable inner VLAN stripping by default when DVM is enabled. If a VSI
supports stripping the inner VLAN in DVM, then it will have to configure
that during runtime. For example if a VF is configured in a port VLAN
while DVM is enabled it will be allowed to offload inner VLANs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support configuring the device in Double VLAN Mode (DVM),
the DDP and FW have to support DVM. If both support DVM, the PF that
downloads the package needs to update the default recipes, set the
VLAN mode, and update boost TCAM entries.
To support updating the default recipes in DVM, add support for
updating an existing switch recipe's lkup_idx and mask. This is done
by first calling the get recipe AQ (0x0292) with the desired recipe
ID. Then, if that is successful update one of the lookup indices
(lkup_idx) and its associated mask if the mask is valid otherwise
the already existing mask will be used.
The VLAN mode of the device has to be configured while the global
configuration lock is held while downloading the DDP, specifically after
the DDP has been downloaded. If supported, the device will default to
DVM.
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new outer_vlan_ops member to the ice_vsi structure as outer VLAN
ops are only available when the device is in Double VLAN Mode (DVM).
Depending on the VSI type, the requirements for what operations to
use/allow differ.
By default all VSI's have unsupported inner and outer VSI VLAN ops. This
implementation was chosen to prevent unexpected crashes due to null
pointer dereferences. Instead, if a VSI calls an unsupported op, it will
just return -EOPNOTSUPP.
Add implementations to support modifying outer VLAN fields for VSI
context. This includes the ability to modify VLAN stripping, insertion,
and the port VLAN based on the outer VLAN handling fields of the VSI
context.
These functions should only ever be used if DVM is enabled because that
means the firmware supports the outer VLAN fields in the VSI context. If
the device is in DVM, then always use the outer_vlan_ops, else use the
vlan_ops since the device is in Single VLAN Mode (SVM).
Also, move adding the untagged VLAN 0 filter from ice_vsi_setup() to
ice_vsi_vlan_setup() as the latter function is specific to the PF and
all other VSI types that need an untagged VLAN 0 filter already do this
in their specific flows. Without this change, Flow Director is failing
to initialize because it does not implement any VSI VLAN ops.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current operations act on inner VLAN fields. To support double VLAN, outer
VLAN operations and functions will be implemented. Add the "inner" naming
to existing VLAN operations to distinguish them from the upcoming outer
values and functions. Some spacing adjustments are made to align
values.
Note that the inner is not talking about a tunneled VLAN, but the second
VLAN in the packet. For SVM the driver uses inner or single VLAN
filtering and offloads and in Double VLAN Mode the driver uses the
inner filtering and offloads for SR-IOV VFs in port VLANs in order to
support offloading the guest VLAN while a port VLAN is configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the proto argument is unused. This is because the driver only
supports 802.1Q VLAN filtering. This policy is enforced via netdev
features that the driver sets up when configuring the netdev, so the
proto argument won't ever be anything other than 802.1Q. However, this
will allow for future iterations of the driver to seemlessly support
802.1ad filtering. Begin using the proto argument and extend the related
structures to support its use.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new struct for VLAN related information. Currently this holds
VLAN ID and priority values, but will be expanded to hold TPID value.
This reduces the changes necessary if any other values are added in
future. Remove the action argument from these calls as it's always
ICE_FWD_VSI.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Incoming changes to support 802.1Q and/or 802.1ad VLAN filtering and
offloads require more flexibility when configuring VLANs. The VSI VLAN
interface will allow flexibility for configuring VLANs for all VSI
types. Add new files to separate the VSI VLAN ops and move functions to
make the code more organized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
XDP_TX workloads use a concept of Tx threshold that indicates the
interval of setting RS bit on descriptors which in turn tells the HW to
generate an interrupt to signal the completion of Tx on HW side. It is
currently based on a constant value of 32 which might not work out well
for various sizes of ring combined with for example batch size that can
be set via SO_BUSY_POLL_BUDGET.
Internal tests based on AF_XDP showed that most convenient setup of
mentioned threshold is when it is equal to quarter of a ring length.
Make use of recently introduced ICE_RING_QUARTER macro and use this
value as a substitute for ICE_TX_THRESH.
Align also ethtool -G callback so that next_dd/next_rs fields are up to
date in terms of the ring size.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20220125160446.78976-5-maciej.fijalkowski@intel.com
In current switchdev implementation, every VF PR is assigned to
individual ring on switchdev ctrl VSI. For slow-path traffic, there
is a mapping VF->ring done in software based on src_vsi value (by
calling ice_eswitch_get_target_netdev function).
With this change, HW solution is introduced which is more
efficient. For each VF, src MAC (VF's MAC) filter will be created,
which forwards packets to the corresponding switchdev ctrl VSI queue
based on src MAC address.
This filter has to be removed and then replayed in case of
resetting one VF. Keep information about this rule in repr->mac_rule,
thanks to that we know which rule has to be removed and replayed
for a given VF.
In case of CORE/GLOBAL all rules are removed
automatically. We have to take care of readding them. This is done
by ice_replay_vsi_adv_rule.
When driver leaves switchdev mode, remove all advanced rules
from switchdev ctrl VSI. This is done by ice_rem_adv_rule_for_vsi.
Flag repr->rule_added is needed because in some cases reset
might be triggered before VF sends request to add MAC.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to enable flow-director filter when multiple TCs are
configured. Flow director filter can be configured using ethtool
(--config-ntuple option). When multiple TCs are configured, each
TC is mapped to an unique HW VSI. So VSI corresponding to queue
used in filter is identified and flow director context is updated
with correct VSI while configuring ntuple filter in HW.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an odd indent where some code was left indented, and causes smatch
to warn:
ice_log_pkg_init() warn: inconsistent indenting
While here, for consistency, add a break after the default case.
This commit has a Fixes: but we caught this while it was only in net-next.
Fixes: 247dd97d71 ("ice: Refactor status flow for DDP load")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20211221230538.2546315-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement support for the basic operations needed to enable the PTP
hardware clock on E822 devices.
This includes implementations for the various PHY access functions, as
well as the ability to start and stop the PHY timers. This is different
from the E810 device because the configuration depends on link speed, so
we cannot just start the PHYs immediately. We must wait until the link
is up to get proper values for the speed based initialization.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The PF reset does not reset PHC and PHY clocks so it's unnecessary to
stop them and reinitialize after the reset.
Configuring timestamping changes the VSI fields so it needs to be
performed after VSIs are initialized, which was not done in case of a
reset.
Suggested-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pasi Vaananen <pvaanane@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver had comments to the effect of: This flag should be set before
calling this function. While reviewing code it was found that there were
several violations of this policy, which could introduce hard to find
bugs or races.
Fix the violations of the "VSI DOWN state must be set before calling
ice_down" and make checking the state into code with a WARN_ON.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As all functions now return standard error codes, propagate the values
being returned instead of converting them to generic values.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
ice_status previously had a variable to contain these values where other
error codes had a variable as well. With ice_status now being an int,
there is no need for two variables to hold error values. In cases where
this occurs, remove one of the excess variables and use a single one.
Some initialization of variables are no longer needed and have been
removed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Remove the ice_stat_str() function which prints the string
representation of the ice_status error code. With upcoming changes
moving away from ice_status, there will be no need for this function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Before this change, final state of the DDP pkg load process was
dependent on many variables such as: ice_status, pkg version,
ice_aq_err. The last one had be stored in hw->pkg_dwnld_status.
It was impossible to conclude this state just from ice_status, that's
why logging process of DDP pkg load in the caller was a little bit
complicated.
With this patch new status enum is introduced - ice_ddp_state.
It covers all the possible final states of the loading process.
What's tricky for ice_ddp_state is that not only
ICE_DDP_PKG_SUCCESS(=0) means that load was successful. Actually
three states mean that:
- ICE_DDP_PKG_SUCCESS
- ICE_DDP_PKG_SAME_VERSION_ALREADY_LOADED
- ICE_DDP_PKG_COMPATIBLE_ALREADY_LOADED
ice_is_init_pkg_successful can tell that information.
One ddp_state should not be used outside of ice_init_pkg which is
ICE_DDP_PKG_ALREADY_LOADED. It is more generic, it is used in
ice_dwnld_cfg_bufs to see if pkg is already loaded. At this point
we can't use one of the specific one (SAME_VERSION, COMPATIBLE,
NOT_SUPPORTED) because we don't have information on the package
currently loaded in HW (we are before calling ice_get_pkg_info).
We can get rid of hw->pkg_dwnld_status because we are immediately
mapping aq errors to ice_ddp_state in ice_dwnld_cfg_bufs.
Other errors like ICE_ERR_NO_MEMORY, ICE_ERR_PARAM are mapped the
generic ICE_DDP_PKG_ERR.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some of the promiscuous mode functions take a boolean to indicate
set/clear, which affects readability. Refactor and provide an
interface for the promiscuous mode code with explicit set and clear
promiscuous mode operations.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver was zeroing live stats that could be fetched by
ndo_get_stats64 at any time. This could result in inconsistent
statistics, and the telltale sign was when reading stats frequently from
/proc/net/dev, the stats would go backwards.
Fix by collecting stats into a local, and delaying when we write to the
structure so it's not incremental.
Fixes: fcea6f3da5 ("ice: Add stats and ethtool support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If the hardware is constantly receiving unicast or broadcast packets
during driver load, the device previously counted many GLV_RDPC (VSI
dropped packets) events during init. This causes confusing dropped
packet statistics during driver load. The dropped packets counter
incrementing does stop once the driver finishes loading.
Avoid this problem by baselining our statistics at the end of driver
open instead of the end of probe.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
