It is reasonable to hold bss_lock for a little bit longer after
cfg80211_bss_update is done. Right now, this does not make any big
difference, but doing so in preparation for the next patch which adds
a call to the driver.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094948.61701884ff0d.I3358228209eb6766202aff04d1bae0b8fdff611f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These calls do not require any locking, so move them in preparation for
the next patches.
A minor change/bugfix is to not hint a beacon for nontransmitted BSSes
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094948.a5bf3558eae9.I33c7465d983c8bef19deb7a533ee475a16f91774@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The check that beacon primary channel is in the range of 80 MHz
(abs < 80) is invalid for 320 MHz since duplicate beacon transmit
means that the AP transmits it on all the 20 MHz sub-channels:
9.4.2.249 HE Operation element - ... AP transmits Beacon frames in
non-HT duplicate PPDU with a TXVECTOR parameter CH_BANDWIDTH value
that is up to the BSS bandwidth.
So in case of 320 MHz the DUP beacon can be in upper 160 for primary
channel in the lower 160 giving possibly an absolute range of over
80 MHz.
Also this check is redundant alltogether, if AP has a wrong primary
channel in the beacon it's a faulty AP, and we would fail in next
steps to connect.
While at it, fix the frequency comparison to no longer compare
between KHz and MHz, which was introduced by commit 7f599aeccb
("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel").
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.314faf725255.I5e27251ac558297553b590d3917a7b6d1aae0e74@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in case DUP bit is not set we don't return the primary
channel for 6 GHz Band, but the spec says that the DUP bit has
no effect on this field:
9.4.2.249 HE Operation element:
The Duplicate Beacon subfield is set to 1 if the AP transmits
Beacon frames in non-HT duplicate PPDU with a TXVECTOR parameter
CH_BANDWIDTH value that is up to the BSS bandwidth and is set to
0 otherwise.
So remove the condition for returning primary channel based on DUP.
Since the caller code already marks the signal as invalid in case
the indicated frequency is not the tuned frequency, there's no need
to additionally handle this case here since that's already true for
duplicated beacons on the non-primary channel(s).
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.66d7f05f7d11.I5e0add054f72ede95611391b99804c61c40cc959@changeid
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.
Major changes:
ath10k
* store WLAN firmware version in SMEM image table
mt76
* mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
* mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
* mt7915: add ack signal support
* mt7915: enable coredump support
* mt7921: remain_on_channel support
* mt7921: channel context support
iwlwifi
* enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
* 320 MHz channels support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmOKcMARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZv3cgf+KjlbxtCZvEIfK+jsd2/VK635ucUdC1d5
QZB5SCHyVCqTMEsBBw0WCmFdfnqQRQUE9Qe5s0hlwhyrjLP4FQ6/jGTarFvRV43E
xO8jJd7e4mnVVoQySeKIRfvtYPFKT5GpaDVs4ytfdSs+KYoCE7akMBcvHVO8Fr2M
MepdqyoJakhRybFUJZMts8W8IsBikv9hdnb2Mr/E32JFLeP6ggs9tKCZKBbpxyXk
BzfYkDMXffFl95prlmy4rXP223FjvgUuRNWaatseR7S6A/Ik9Xk3B1qv3mtocPZF
LiTlFtmn3qkgyX5bfm6NRe/2FqgRUYfIrN0XtVw6Sy8WUe1GCf3opA==
=pkqE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.2
Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.
Major changes:
ath10k
- store WLAN firmware version in SMEM image table
mt76
- mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
- mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
- mt7915: add ack signal support
- mt7915: enable coredump support
- mt7921: remain_on_channel support
- mt7921: channel context support
iwlwifi
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
* tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (144 commits)
wifi: ath10k: fix QCOM_SMEM dependency
wifi: mt76: mt7921e: add pci .shutdown() support
wifi: mt76: mt7915: mmio: fix naming convention
wifi: mt76: mt7996: add support to configure spatial reuse parameter set
wifi: mt76: mt7996: enable ack signal support
wifi: mt76: mt7996: enable use_cts_prot support
wifi: mt76: mt7915: rely on band_idx of mt76_phy
wifi: mt76: mt7915: enable per bandwidth power limit support
wifi: mt76: mt7915: introduce mt7915_get_power_bound()
mt76: mt7915: Fix PCI device refcount leak in mt7915_pci_init_hif2()
wifi: mt76: do not send firmware FW_FEATURE_NON_DL region
wifi: mt76: mt7921: Add missing __packed annotation of struct mt7921_clc
wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices
wifi: mt76: mt76x0: remove dead code in mt76x0_phy_get_target_power
wifi: mt76: mt7915: fix band_idx usage
wifi: mt76: mt7915: enable .sta_set_txpwr support
wifi: mt76: mt7915: add basedband Txpower info into debugfs
wifi: mt76: mt7915: add support to configure spatial reuse parameter set
wifi: mt76: mt7915: add missing MODULE_PARM_DESC
...
====================
Link: https://lore.kernel.org/r/20221202214254.D0D3DC433C1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no need to open-code container_of() when we have
bss_from_pub(). Use it.
Change-Id: I074723717909ba211a40e6499f0c36df0e2ba4be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the "channel->freq_offset" comparison is omitted in cmp_bss(),
BSS with different kHz units cannot be distinguished in the S1G Band.
So "freq_offset" should also be included in the comparison.
Signed-off-by: JUN-KYU SHIN <jk.shin@newratek.com>
Link: https://lore.kernel.org/r/20221111023301.6395-1-jk.shin@newratek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In S1G beacon frames there shouldn't be multi-BSSID elements
since that's not supported, remove that to avoid a potential
integer underflow and/or misparsing the frames due to the
different length of the fixed part of the frame.
While at it, initialize non_tx_data so we don't send garbage
values to the user (even if it doesn't seem to matter now.)
Reported-and-tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 9eaffe5078 ("cfg80211: convert S1G beacon to scan results")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For vendor elements, the code here assumes that 5 octets
are present without checking. Since the element itself is
already checked to fit, we only need to check the length.
Reported-and-tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Second set of patches for v6.2. Only driver patches this time, nothing
really special. Unused platform data support was removed from wl1251
and rtw89 got WoWLAN support.
Major changes:
ath11k
* support configuring channel dwell time during scan
rtw89
* new dynamic header firmware format support
* Wake-over-WLAN support
rtl8xxxu
* enable IEEE80211_HW_SUPPORT_FAST_XMIT
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmN3ZagRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuk/Af+M9IXyWmis9behHlz2U+4PJ/+JF8VYIck
6Xup+FM0O1w6aHhAL8gNOhLl62jpYB0Exou0YizInGvwjjQk2Gtuq60KshkbN2zL
YK3sbcS66PyE19gfIQKJTW/s+9aBncRuvEb6HTZx5iF96mVFPeBDPduUGQksGs5/
Egf03eAqzdcIIcejKG1SUn2o0fLJ6jds0VftAas+chKI2Z5ADQWPzugvU0vlvXVE
oq3ws7Sg0yGcwOOttFwaXMBPrjmCty5uc/ELMhjvSLAsKULXymjZkrU1m5tanhGu
N1MDqviwCK7PJC/wQ2xo7YKNY/1LUc0xbwfbEXQITfbbPyjOz+ynQQ==
=wKQZ
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.2
Second set of patches for v6.2. Only driver patches this time, nothing
really special. Unused platform data support was removed from wl1251
and rtw89 got WoWLAN support.
Major changes:
ath11k
* support configuring channel dwell time during scan
rtw89
* new dynamic header firmware format support
* Wake-over-WLAN support
rtl8xxxu
* enable IEEE80211_HW_SUPPORT_FAST_XMIT
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When built with Control Flow Integrity, function prototypes between
caller and function declaration must match. These mismatches are visible
at compile time with the new -Wcast-function-type-strict in Clang[1].
Fix a total of 73 warnings like these:
drivers/net/wireless/intersil/orinoco/wext.c:1379:27: warning: cast from 'int (*)(struct net_device *, struct iw_request_info *, struct iw_param *, char *)' to 'iw_handler' (aka 'int (*)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') converts to incompatible function type [-Wcast-function-type-strict]
IW_HANDLER(SIOCGIWPOWER, (iw_handler)orinoco_ioctl_getpower),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../net/wireless/wext-compat.c:1607:33: warning: cast from 'int (*)(struct net_device *, struct iw_request_info *, struct iw_point *, char *)' to 'iw_handler' (aka 'int (*)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') converts to incompatible function type [-Wcast-function-type-strict]
[IW_IOCTL_IDX(SIOCSIWGENIE)] = (iw_handler) cfg80211_wext_siwgenie,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/net/wireless/intersil/orinoco/wext.c:1390:27: error: incompatible function pointer types initializing 'const iw_handler' (aka 'int (*const)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') with an expression of type 'int (struct net_device *, struct iw_request_info *, struct iw_param *, char *)' [-Wincompatible-function-pointer-types]
IW_HANDLER(SIOCGIWRETRY, cfg80211_wext_giwretry),
^~~~~~~~~~~~~~~~~~~~~~
The cfg80211 Wireless Extension handler callbacks (iw_handler) use a
union for the data argument. Actually use the union and perform explicit
member selection in the function body instead of having a function
prototype mismatch. There are no resulting binary differences
before/after changes.
These changes were made partly manually and partly with the help of
Coccinelle.
Link: https://github.com/KSPP/linux/issues/234
Link: https://reviews.llvm.org/D134831 [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/a68822bf8dd587988131bb6a295280cb4293f05d.1667934775.git.gustavoars@kernel.org
All we're going to do with this pointer is assign it to
another __rcu pointer, but sparse can't see that, so
use rcu_access_pointer() to silence the warning here.
Fixes: c90b93b5b7 ("wifi: cfg80211: update hidden BSSes to avoid WARN_ON")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When updating beacon elements in a non-transmitted BSS,
also update the hidden sub-entries to the same beacon
elements, so that a future update through other paths
won't trigger a WARN_ON().
The warning is triggered because the beacon elements in
the hidden BSSes that are children of the BSS should
always be the same as in the parent.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a non-transmitted BSS shares enough information (both
SSID and BSSID!) with another non-transmitted BSS of a
different AP, then we can find and update it, and then
try to add it to the non-transmitted BSS list. We do a
search for it on the transmitted BSS, but if it's not
there (but belongs to another transmitted BSS), the list
gets corrupted.
Since this is an erroneous situation, simply fail the
list insertion in this case and free the non-transmitted
BSS.
This fixes CVE-2022-42721.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are multiple refcounting bugs related to multi-BSSID:
- In bss_ref_get(), if the BSS has a hidden_beacon_bss, then
the bss pointer is overwritten before checking for the
transmitted BSS, which is clearly wrong. Fix this by using
the bss_from_pub() macro.
- In cfg80211_bss_update() we copy the transmitted_bss pointer
from tmp into new, but then if we release new, we'll unref
it erroneously. We already set the pointer and ref it, but
need to NULL it since it was copied from the tmp data.
- In cfg80211_inform_single_bss_data(), if adding to the non-
transmitted list fails, we unlink the BSS and yet still we
return it, but this results in returning an entry without
a reference. We shouldn't return it anyway if it was broken
enough to not get added there.
This fixes CVE-2022-42720.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: a3584f56de ("cfg80211: Properly track transmitting and non-transmitting BSS")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When iterating the elements here, ensure the length byte is
present before checking it to see if the entire element will
fit into the buffer.
Longer term, we should rewrite this code using the type-safe
element iteration macros that check all of this.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Reported-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Per spec, the maximum value for the MaxBSSID ('n') indicator is 8,
and the minimum is 1 since a multiple BSSID set with just one BSSID
doesn't make sense (the # of BSSIDs is limited by 2^n).
Limit this in the parsing in both cfg80211 and mac80211, rejecting
any elements with an invalid value.
This fixes potentially bad shifts in the processing of these inside
the cfg80211_gen_new_bssid() function later.
I found this during the investigation of CVE-2022-41674 fixed by the
previous patch.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the copy code of the elements, we do the following calculation
to reach the end of the MBSSID element:
/* copy the IEs after MBSSID */
cpy_len = mbssid[1] + 2;
This looks fine, however, cpy_len is a u8, the same as mbssid[1],
so the addition of two can overflow. In this case the subsequent
memcpy() will overflow the allocated buffer, since it copies 256
bytes too much due to the way the allocation and memcpy() sizes
are calculated.
Fix this by using size_t for the cpy_len variable.
This fixes CVE-2022-41674.
Reported-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on changes in the specification the TBTT information in
the RNR can include MLD information, so update the parsing to
allow extracting the short SSID information in such a case.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When retrieving the S1G channel number from IEs, we should retrieve
the operating channel instead of the primary channel. The S1G operation
element specifies the main channel of operation as the oper channel,
unlike for HT and HE which specify their main channel of operation as
the primary channel.
Signed-off-by: Kieran Frewen <kieran.frewen@morsemicro.com>
Signed-off-by: Bassem Dawood <bassem@morsemicro.com>
Link: https://lore.kernel.org/r/20220420041321.3788789-1-kieran.frewen@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Synchronize additions to nontrans_list of transmitting BSS with
bss_lock to avoid races. Also when cfg80211_add_nontrans_list() fails
__cfg80211_unlink_bss() needs bss_lock to be held (has lockdep assert
on bss_lock). So protect the whole block with bss_lock to avoid
races and warnings. Found during code review.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649668071-9370-1-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding 6GHz channels to scan request based on reported
co-located APs, don't add channels that have only APs with
"non-transmitted" BSSes if they only match the wildcard SSID since
they will be found by probing the "transmitted" BSS.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.f6ddf099f934.I231e55885d3644f292d00dfe0f42653269f2559e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A non-collocated AP whose primary channel is not a PSC channel
may transmit a duplicated beacon on the corresponding PSC channel
in which it would indicate its true primary channel.
Use this inforamtion contained in the HE operation IE to determine
the primary channel of the AP.
In case of invalid infomration ignore it and use the channel
the frame was received on.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211202143322.71eb2176e54e.I130f678e4aa390973ab39d838bbfe7b2d54bff8e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When kzalloc failed and rdev->sacn_req or rdev->scan_msg is null, pass a
null pointer to kfree is redundant, delete it and return directly.
Signed-off-by: liuguoqiang <liuguoqiang@uniontech.com>
Link: https://lore.kernel.org/r/20211115092139.24407-1-liuguoqiang@uniontech.com
[remove now unused creq = NULL assigment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get channel number from ies is a common logic, so separate it to a new
function, which could also be used by lower driver.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210930081533.4898-1-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'if (dev)' statement already move into dev_{put , hold}, so remove
redundant if statements.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we exceed the limit of BSS entries, this function will free the
new entry, however, at this time, it is the last door to access the
inputed ies, so these ies will be unreferenced objects and cause memory
leak.
Therefore we should free its ies before deallocating the new entry, beside
of dropping it from hidden_list.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210628132334.851095-1-phind.uet@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To discover a hidden AP on the 6GHz band, the probe request
sent to the AP needs to include the AP's SSID, as some APs
would not respond with a probe response based only on short
SSID match.
To support hidden AP discovery over the 6GHz band,
when constructing the specific 6GHz band scan also include
SSIDs that were part of the original scan request, so these
can be used in the probe requests transmitted during scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.218df9d3203c.Ice0f7a2f6a65f1f9710b7898591481baeefaf490@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "ap_info->tbtt_info_len" and "length" variables are the same value
but it is confusing how the names are mixed up. Let's use "length"
everywhere for consistency.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YJaMNzZENkYFAYQX@mwanda
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
-----BEGIN PGP SIGNATURE-----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=b0NQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of updates, all over the map:
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of scan request with wildcard SSID, or in case of more
than one SSID in scan request, need to scan PSC channels even though
all the co-located APs found during the legacy bands scan indicated
that all the APs in their ESS are co-located, as we might find different
networks on the PSC channels.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201129172929.736415a9ca5d.If5b3578ae85e11a707a5da07e66ba85928ba702c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The for-loop iterates with a u8 loop counter and compares this
with the loop upper limit of request->n_ssids which is an int type.
There is a potential infinite loop if n_ssids is larger than the
u8 loop counter, so fix this by making the loop counter an int.
Addresses-Coverity: ("Infinite loop")
Fixes: c8cb5b854b ("nl80211/cfg80211: support 6 GHz scanning")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201029222407.390218-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The S1G beacon is an extension frame as opposed to
management frame for the regular beacon. This means we may
have to occasionally cast the frame buffer to a different
header type. Luckily this isn't too bad as scan results
mostly only care about the IEs.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-6-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support 6 GHz scanning, by
* a new scan flag to scan for colocated BSSes advertised
by (and found) APs on 2.4 & 5 GHz
* doing the necessary reduced neighbor report parsing for
this, to find them
* adding the ability to split the scan request in case the
device by itself cannot support this.
Also add some necessary bits in mac80211 to not break with
these changes.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.
The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.
iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.
When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.
iwlwifi will call this new API any time the firmware is started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20200625111524.3992-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:
MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
Also provide some helper functions to do the frequency
conversion and test for equality.
Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.
Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.
mesh, ibss, wext, etc. are currently ignored.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When cfg80211_update_assoc_bss_entry() is called, there is a
verification that the BSS channel actually changed. As some APs use
CSA also for bandwidth changes, this would result with a kernel
warning.
Fix this by removing the WARN_ON().
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.96316ada0e8d.I6710376b1b4257e5f4712fc7ab16e2b638d512aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rdev->sched_scan_req_list maybe traversed using list_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of rtnl_mutex.
Hence, add corresponding lockdep expression to silence false-positive
warnings, and harden RCU lists.
Signed-off-by: Amol Grover <frextrite@gmail.com>
Link: https://lore.kernel.org/r/20200219091102.10709-1-frextrite@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_update_notlisted_nontrans() leaves the RCU critical session
too early, while still using nontrans_ssid which is RCU protected. In
addition, it performs a bunch of RCU pointer update operations such
as rcu_access_pointer and rcu_assign_pointer.
The caller, cfg80211_inform_bss_frame_data(), also accesses the RCU
pointer without holding the lock.
Just wrap all of this with bss_lock.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20191004123706.15768-3-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code copying the data assumes that the SSID element is
before the MBSSID element, but since the data is untrusted
from the AP, this cannot be guaranteed.
Validate that this is indeed the case and ignore the MBSSID
otherwise, to avoid having to deal with both cases for the
copy of data that should be between them.
Cc: stable@vger.kernel.org
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Link: https://lore.kernel.org/r/1569009255-I1673911f5eae02964e21bdc11b2bf58e5e207e59@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When associated BSS completes channel switch procedure, its channel
record needs to be updated. The existing mac80211 solution was
extended to cfg80211 in commit 5dc8cdce1d ("mac80211/cfg80211:
update bss channel on channel switch").
However that solution still appears to be incomplete as it may lead
to duplicated scan entries for associated BSS after channel switch.
The root cause of the problem is as follows. Each BSS entry is
included into the following data structures:
- bss list rdev->bss_list
- bss search tree rdev->bss_tree
Updating BSS channel record without rebuilding bss_tree may break
tree search since cmp_bss considers all of the following: channel,
bssid, ssid. When BSS channel is updated, but its location in bss_tree
is not updated, then subsequent search operations may fail to locate
this BSS since they will be traversing bss_tree in wrong direction.
As a result, for scan performed after associated BSS channel switch,
cfg80211_bss_update may add the second entry for the same BSS to both
bss_list and bss_tree, rather then update the existing one.
To summarize, if BSS channel needs to be updated, then bss_tree should
be rebuilt in order to put updated BSS entry into a proper location.
This commit suggests the following straightforward solution:
- if new entry has been already created for BSS after channel switch,
then use its IEs to update known BSS entry and then remove new
entry completely
- use rb_erase/rb_insert_bss reinstall updated BSS in bss_tree
- for nontransmit BSS entry, the whole transmit BSS hierarchy
is updated
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190726163922.27509-3-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements minor refactoring for cfg80211_bss_update function.
Code path for updating known BSS is extracted into dedicated
cfg80211_update_known_bss function.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190726163922.27509-2-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we just read jiffies over and over again, a non-transmitting
entry may have a newer timestamp than the transmitting one,
leading to possible confusion on expiry. Give them all the same
timestamp when creating them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190703133823.10530-3-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't parse the multi-BSSID structures if we couldn't even create
their transmitting BSS, this would confuse all of our tracking.
This also means that non_tx_data->tx_bss will never be NULL, so
we can clean up a little bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190703133823.10530-2-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_inform_single_bss_frame_data() doesn't need the
non_tx_data data argument since it's always NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190703133823.10530-1-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The seen_indices variable is u64 and in other parts of the code we
assume mbssid_index_ie[2] can be up to 45, so we should use the 64-bit
versions of BIT, namely, BIT_ULL().
Reported-by: Dan Carpented <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a function that iterates over the BSS entries associated with a
given wiphy and calls a callback for each iterated BSS. This can be
used by drivers in various ways, e.g., to evaluate some property for
all the BSSs in the medium.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the BSS is expired during connection, the connect result will
trigger a kernel warning. Ideally cfg80211 should hold the BSS
before the connection is attempted, but as the BSSID is not known
in case of auth/assoc MLME offload (connect op) it doesn't.
For those drivers without the connect op cfg80211 holds down the
reference so it wil not be removed from list.
Fix this by removing the warning and silently adding the BSS back to
the bss list which is return by the driver (with proper BSSID set) or
in case the BSS is already added use that.
The requirements for drivers are documented in the API's.
Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk>
[formatting fixes, keep old timestamp]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
-----BEGIN PGP SIGNATURE-----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=JQOx
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cfg80211_merge_profile() and ieee802_11_find_bssid_profile() are
a bit cleaner if we just pass the merged_ie pointer instead of a pointer
to the pointer.
This isn't a functional change, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since an element is limited to 255 octets, a profile may be split
split to several elements. Support the split as defined in the 11ax
draft 3. Detect legacy split and print a net-rate limited warning,
since there is no ROI in supporting this probably non-existent
split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Subelement profile may specify element IDs it doesn't inherit
from the management frame. Support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When creating the IEs for the nontransmitted BSS, the index
element is skipped. However, we need to get DTIM values from
it, so don't skip it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use kmemdup rather than duplicating its implementation
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
new_ie is used as a temporary storage for the generation of
the new elements. However, after copying from it the memory
wasn't freed and leaked. Free it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extension IEs have ID 255 followed by extension ID. Current
code is buggy in handling it in two ways:
1. When checking if IE is in the frame, it uses just the ID, which
for extension elements is too broad.
2. It uses 0xFF to mark copied IEs, which will result in not copying
extension IEs from the subelement.
Fix both issue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the new IEs are generated, the multiple BSSID elements
are not saved. Save aside properties that are needed later
for PS.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parsing and exposing nontransmitted APs is problematic
when underlying HW doesn't support it. Do it only if
driver indicated support. Allow HE restriction as well,
since the HE spec defined the exact manner that Multiple
BSSID set should behave. APs that not support the HE
spec will have less predictable Multiple BSSID set
support/behavior
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the transmitted BSS and the non-trasmitted BSS list were
defined in struct cfg80211_internal_bss. Move them to struct cfg80211_bss
since mac80211 needs this info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When holding data of the non-transmitting BSS, we need to keep the
transmitting BSS data on. Otherwise it will be released, and release
the non-transmitting BSS with it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the new for_each_element() helper here, we cannot use
for_each_subelement() since we have a fixed 1 byte before
the subelements start.
While at it, also fix le16_to_cpup() to be get_unaligned_le16()
since we don't know anything about alignment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends cfg80211 BSS table processing to be able to parse Multiple
BSSID element from Beacon and Probe Response frames and to update the
BSS profiles in internal database for non-transmitted BSSs.
Signed-off-by: Peng Xu <pxu@codeaurora.org>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently have a number of helpers to find elements that just
return a u8 *, change those to return a struct element and add
inlines to deal with the u8 * compatibility.
Note that the match behaviour is changed to start the natch at
the data, so conversion from _ie_match to _elem_match need to
be done carefully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it and since we'll need it, also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e. it was able to parse all of
the elements successfully and no data remained.
Use for_each_element_id() in cfg80211_find_ie_match() as the
first user of this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are talks about enabling -Wimplicit-fallthrough warnings in the
mainline and it is already enabled in linux-next. Add all the
missing annotations to prevent warnings when this happens.
And in one case, remove the extra text from the annotation so that the
compiler recognizes it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_get_bss_channel() is used to update the RX channel based on the
available frame payload information (channel number from DSSS Parameter
Set element or HT Operation element). This is needed on 2.4 GHz channels
where frames may be received on neighboring channels due to overlapping
frequency range.
This might of some use on the 5 GHz band in some corner cases, but
things are more complex there since there is no n:1 or 1:n mapping
between channel numbers and frequencies due to multiple different
starting frequencies in different operating classes. This could result
in ieee80211_channel_to_frequency() returning incorrect frequency and
ieee80211_get_channel() returning incorrect channel information (or
indication of no match). In the previous implementation, this could
result in some scan results being dropped completely, e.g., for the 4.9
GHz channels. That prevented connection to such BSSs.
Fix this by using the driver-provided channel pointer if
ieee80211_get_channel() does not find matching channel data for the
channel number in the frame payload and if the scan is done with 5 MHz
or 10 MHz channel bandwidth. While doing this, also add comments
describing what the function is trying to achieve to make it easier to
understand what happens here and why.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit enhances the scan results to report the per chain signal
strength based on the latest BSS update. This provides similar
information to what is already available through STA information.
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-scheduled scan support in subsequent patch a request id
will be added. This patch add this request id to the scheduled
scan event messages. For now the request id will always be zero.
With multi-scheduled scan its value will inform user-space to which
scan the event relates.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A couple of functions used with scan events were named with
term "send" although they were only preparing the the event
message so renamed those.
Also remove nl80211_send_sched_scan_results() in favor of
just calling nl80211_send_sched_scan() with the right value.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[mention nl80211_send_sched_scan_results() in the commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's possible to make scanning consume almost arbitrary amounts
of memory, e.g. by sending beacon frames with random BSSIDs at
high rates while somebody is scanning.
Limit the number of BSS table entries we're willing to cache to
1000, limiting maximum memory usage to maybe 4-5MB, but lower
in practice - that would be the case for having both full-sized
beacon and probe response frames for each entry; this seems not
possible in practice, so a limit of 1000 entries will likely be
closer to 0.5 MB.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few places where an IE that matches not only the EID, but
also other bytes inside the element, needs to be found. To simplify
that and reduce the amount of similar code, implement a new helper
function to match the EID and an extra array of bytes.
Additionally, simplify cfg80211_find_vendor_ie() by using the new
match function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows finding vendor IE from a specific vendor.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
