intel_pch_thermal driver needs a long delay to cool itself (60 seconds
in maximum) during suspend. When a wakeup event occures during the
delay, it is better for the intel_pch_thermal driver to detect this and
quit cooling because the suspend is likely to abort anyway.
Thus expose pm_wakeup_pending to modules so that intel_pch_thermal
driver can be aware of the wakeup events.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To move towards a more consistent behaviour between genpd and the runtime
PM core, let's start by converting genpd's time-accounting from ktime_get()
into ktime_get_mono_fast_ns().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The only two users of __pm_runtime_set_status() are pm_runtime_set_active()
and pm_runtime_set_suspended(). These are widely used and should be called
from non-atomic context to work as expected. However, it would be
convenient to allow them be called from atomic context too, as shown from a
subsequent change, so let's add support for this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Maulik Shah <quic_mkshah@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A PM-runtime device usage count underflow is potentially critical,
because it may cause a device to be suspended when it is expected to
be operational. It is also a programming problem that would be good
to catch and warn about.
For this reason, (1) make rpm_check_suspend_allowed() return an error
when the device usage count is negative to prevent devices from being
suspended in that case, (2) introduce rpm_drop_usage_count() that will
detect device usage count underflows, warn about them and fix them up,
and (3) use it to drop the usage count in a few places instead of
atomic_dec_and_test().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Mention all domain attach menthods which dev_pm_domain_detach()
reverses.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge changes related to system sleep, PM domains changes and power
management documentation changes for 5.18-rc1:
- Fix load_image_and_restore() error path (Ye Bin).
- Fix typos in comments in the system wakeup hadling code (Tom Rix).
- Clean up non-kernel-doc comments in hibernation code (Jiapeng
Chong).
- Fix __setup handler error handling in system-wide suspend and
hibernation core code (Randy Dunlap).
- Add device name to suspend_report_result() (Youngjin Jang).
- Make virtual guests honour ACPI S4 hardware signature by
default (David Woodhouse).
- Block power off of a parent PM domain unless child is in deepest
state (Ulf Hansson).
- Use dev_err_probe() to simplify error handling for generic PM
domains (Ahmad Fatoum).
- Fix sleep-in-atomic bug caused by genpd_debug_remove() (Shawn Guo).
- Document Intel uncore frequency scaling (Srinivas Pandruvada).
* pm-sleep:
PM: hibernate: Honour ACPI hardware signature by default for virtual guests
PM: sleep: Add device name to suspend_report_result()
PM: suspend: fix return value of __setup handler
PM: hibernate: fix __setup handler error handling
PM: hibernate: Clean up non-kernel-doc comments
PM: sleep: wakeup: Fix typos in comments
PM: hibernate: fix load_image_and_restore() error path
* pm-domains:
PM: domains: Fix sleep-in-atomic bug caused by genpd_debug_remove()
PM: domains: use dev_err_probe() to simplify error handling
PM: domains: Prevent power off for parent unless child is in deepest state
* pm-docs:
Documentation: admin-guide: pm: Document uncore frequency scaling
Currently, suspend_report_result() prints only function information.
If any driver uses a common PM function, nobody knows who exactly
called the failing function.
A device pinter is needed to recognize the failing device.
For example:
PM: dpm_run_callback(): pnp_bus_suspend+0x0/0x10 returns 0
PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns 0
become after the change:
serial 00:05: PM: dpm_run_callback(): pnp_bus_suspend+0x0/0x10 returns 0
pci 0000:00:01.3: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns 0
Signed-off-by: Youngjin Jang <yj84.jang@samsung.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM Runtime docs say:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
From grepping code, it's clear that many people aren't aware of the
need to call pm_runtime_dont_use_autosuspend().
When brainstorming solutions, one idea that came up was to leverage
the new-ish devm_pm_runtime_enable() function. The idea here is that:
* When the devm action is called we know that the driver is being
removed. It's the perfect time to undo the use_autosuspend.
* The code of pm_runtime_dont_use_autosuspend() already handles the
case of being called when autosuspend wasn't enabled.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the second 'the'.
Replace the second 'of' with 'the'.
Replace 'couter' with 'counter'.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_err_probe() can reduce code size, makes the code easier to read
and has the added benefit of recording the defer reason for later
read out. Use it where appropriate.
This also fixes an issue, where an error message in __genpd_dev_pm_attach
was not terminated by a line break.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A PM domain managed by genpd may support multiple idlestates (power-off
states). During genpd_power_off() a genpd governor may be asked to select
one of the idlestates based upon the dev PM QoS constraints, for example.
However, there is a problem with the behaviour around this in genpd. More
precisely, a parent-domain is allowed to be powered off, no matter of what
idlestate that has been selected for the child-domain.
For the stm32mp1 platform from STMicro, this behaviour doesn't play well.
Instead, the parent-domain must not be powered off, unless the deepest
idlestate has been selected for the child-domain. As the current behaviour
in genpd is quite questionable anyway, let's simply change it into what is
needed by the stm32mp1 platform.
If it surprisingly turns out that other platforms may need a different
behaviour from genpd, then we will have to revisit this to find a way to
make it configurable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit e3728b50cd ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed. Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.
The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop(). However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.
To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup. Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one. [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]
Fixes: e3728b50cd ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
New driver:
- Sunplus SP7021 RTC
- Nintendo GameCube, Wii and Wii U RTC
Drivers:
- cmos: refactor UIP handling and presence check, fix century
- rs5c372: offset correction support, report low voltage
- rv8803: Epson RX8804 support
-----BEGIN PGP SIGNATURE-----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=nwD6
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Two new drivers this cycle and a significant rework of the CMOS driver
make the bulk of the changes.
I also carry powerpc changes with the agreement of Michael.
New drivers:
- Sunplus SP7021 RTC
- Nintendo GameCube, Wii and Wii U RTC
Driver updates:
- cmos: refactor UIP handling and presence check, fix century
- rs5c372: offset correction support, report low voltage
- rv8803: Epson RX8804 support"
* tag 'rtc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (33 commits)
rtc: sunplus: fix return value in sp_rtc_probe()
rtc: cmos: Evaluate century appropriate
rtc: gamecube: Fix an IS_ERR() vs NULL check
rtc: mc146818-lib: fix signedness bug in mc146818_get_time()
dt-bindings: rtc: qcom-pm8xxx-rtc: update register numbers
rtc: pxa: fix null pointer dereference
rtc: ftrtc010: Use platform_get_irq() to get the interrupt
rtc: Move variable into switch case statement
rtc: pcf2127: Fix typo in comment
dt-bindings: rtc: Add Sunplus RTC json-schema
rtc: Add driver for RTC in Sunplus SP7021
rtc: rs5c372: fix incorrect oscillation value on r2221tl
rtc: rs5c372: add offset correction support
rtc: cmos: avoid UIP when writing alarm time
rtc: cmos: avoid UIP when reading alarm time
rtc: mc146818-lib: refactor mc146818_does_rtc_work
rtc: mc146818-lib: refactor mc146818_get_time
rtc: mc146818-lib: extract mc146818_avoid_UIP
rtc: mc146818-lib: fix RTC presence check
rtc: Check return value from mc146818_get_time()
...
Notice that pm_runtime_put_suppliers() cannot be called with
disabled interrupts, because it may sleep (due to the device
links read locking in the non-SRCU case), and so it can use
spin_lock_irq() and spin_unlock_irq() for the locking.
Update the function accordingly and while at it move the "put"
local variable in it into the inner block where it is used.
This change is not expected to have any visible functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 2aa36604e8 ("PM: sleep: Avoid calling put_device() under
dpm_list_mtx") forgot to update the while () loop termination
condition to also break the loop if error is nonzero, which
causes the loop to become infinite if device_prepare() returns
an error for one device.
Add the missing !error check.
Fixes: 2aa36604e8 ("PM: sleep: Avoid calling put_device() under dpm_list_mtx")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Because refcount_dec_not_one() returns true if the target refcount
becomes saturated, it is generally unsafe to use its return value as
a loop termination condition, but that is what happens when a device
link's supplier device is released during runtime PM suspend
operations and on device link removal.
To address this, introduce pm_runtime_release_supplier() to be used
in the above cases which will check the supplier device's runtime
PM usage counter in addition to the refcount_dec_not_one() return
value, so the loop can be terminated in case the rpm_active refcount
value becomes invalid, and update the code in question to use it as
appropriate.
This change is not expected to have any visible functional impact.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
In some cases (for example, during system-wide suspend and resume of
devices) it is useful to know whether or not runtime PM has ever been
enabled for a given device and, if so, what the runtime PM status of
it had been right before runtime PM was disabled for it last time.
For this reason, introduce a new struct dev_pm_info field called
last_status that will be used for capturing the runtime PM status of
the device when its power.disable_depth counter changes from 0 to 1.
The new field will be set to RPM_INVALID to start with and whenever
power.disable_depth changes from 1 to 0, so it will be valid only
when runtime PM of the device is currently disabled, but it has been
enabled at least once.
Immediately use power.last_status in rpm_resume() to make it handle
the case when PM runtime is disabled for the device, but its runtime
PM status is RPM_ACTIVE more consistently. Namely, make it return 1
if power.last_status is also equal to RPM_ACTIVE in that case (the
idea being that if the status was RPM_ACTIVE last time when
power.disable_depth was changing from 0 to 1 and it is still
RPM_ACTIVE, it can be assumed to reflect what happened to the device
last time when it was using runtime PM) and -EACCES otherwise.
Update the documentation to provide a description of last_status and
change the description of pm_runtime_resume() in it to reflect the
new behavior of rpm_active().
While at it, rearrange the code in pm_runtime_enable() to be more
straightforward and replace the WARN() macro in it with a pr_warn()
invocation which is less disruptive.
Link: https://lore.kernel.org/linux-pm/20211026222626.39222-1-ulf.hansson@linaro.org/t/#u
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are 4 users of mc146818_get_time() and none of them was checking
the return value from this function. Change this.
Print the appropriate warnings in callers of mc146818_get_time() instead
of in the function mc146818_get_time() itself, in order not to add
strings to rtc-mc146818-lib.c, which is kind of a library.
The callers of alpha_rtc_read_time() and cmos_read_time() may use the
contents of (struct rtc_time *) even when the functions return a failure
code. Therefore, set the contents of (struct rtc_time *) to 0x00,
which looks more sensible then 0xff and aligns with the (possibly
stale?) comment in cmos_read_time:
/*
* If pm_trace abused the RTC for storage, set the timespec to 0,
* which tells the caller that this RTC value is unusable.
*/
For consistency, do this in mc146818_get_time().
Note: hpet_rtc_interrupt() may call mc146818_get_time() many times a
second. It is very unlikely, though, that the RTC suddenly stops
working and mc146818_get_time() would consistently fail.
Only compile-tested on alpha.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-alpha@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-4-mat.jonczyk@o2.pl
In the cpuidle-psci case, runtime PM in combination with the generic PM
domain (genpd), may be used when entering/exiting a shared idlestate. More
precisely, genpd relies on runtime PM to be enabled for the attached device
(in this case it belongs to a CPU), to properly manage the reference
counting of its PM domain.
This works fine most of the time, but during system suspend in
dpm_suspend_late(), the PM core disables runtime PM for all devices. Beyond
this point, calls to pm_runtime_get_sync() to runtime resume a device may
fail and therefore it could also mess up the reference counting in genpd.
To fix this problem, let's call wake_up_all_idle_cpus() in
dpm_suspend_late(), prior to disabling runtime PM. In this way a device
that belongs to a CPU, becomes runtime resumed through cpuidle-psci and
stays like that, because the runtime PM usage count has been bumped in
device_prepare().
Diagnosed-by: Maulik Shah <mkshah@codeaurora.org>
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge updates related to system sleep for 5.16-rc1:
- Clean up hib_wait_io() (Falla Coulibaly).
- Fix sparse warnings in hibernation-related code (Anders Roxell).
- Use vzalloc() and kzalloc() instead of their open-coded
equivalents in hibernation-related code (Cai Huoqing).
- Prevent user space from crashing the kernel by attempting to
restore the system state from a swap partition in use (Ye Bin).
- Do not let "syscore" devices runtime-suspend during system PM
transitions (Rafael Wysocki).
- Do not pause cpuidle in the suspend-to-idle path (Rafael Wysocki).
- Pause cpuidle later and resume it earlier during system PM
transitions (Rafael Wysocki).
- Make system suspend code use valid_state() consistently (Rafael
Wysocki).
- Add support for enabling wakeup IRQs after invoking the
->runtime_suspend() callback and make two drivers use it (Chunfeng
Yun).
* pm-sleep:
usb: mtu3: enable wake-up interrupt after runtime_suspend called
usb: xhci-mtk: enable wake-up interrupt after runtime_suspend called
PM / wakeirq: support enabling wake-up irq after runtime_suspend called
PM: suspend: Use valid_state() consistently
PM: sleep: Pause cpuidle later and resume it earlier during system transitions
PM: suspend: Do not pause cpuidle in the suspend-to-idle path
PM: sleep: Do not let "syscore" devices runtime-suspend during system transitions
PM: hibernate: Get block device exclusively in swsusp_check()
PM: hibernate: swap: Use vzalloc() and kzalloc()
PM: hibernate: fix sparse warnings
Revert "PM: sleep: Do not assume that "mem" is always present"
PM: hibernate: Remove blk_status_to_errno in hib_wait_io
PM: sleep: Do not assume that "mem" is always present
When the dedicated wake IRQ is level trigger, and it uses the
device's low-power status as the wakeup source, that means if the
device is not in low-power state, the wake IRQ will be triggered
if enabled; For this case, need enable the wake IRQ after running
the device's ->runtime_suspend() which make it enter low-power state.
e.g.
Assume the wake IRQ is a low level trigger type, and the wakeup
signal comes from the low-power status of the device.
The wakeup signal is low level at running time (0), and becomes
high level when the device enters low-power state (runtime_suspend
(1) is called), a wakeup event at (2) make the device exit low-power
state, then the wakeup signal also becomes low level.
------------------
| ^ ^|
---------------- | | --------------
|<---(0)--->|<--(1)--| (3) (2) (4)
if enable the wake IRQ before running runtime_suspend during (0),
a wake IRQ will arise, it causes resume immediately;
it works if enable wake IRQ ( e.g. at (3) or (4)) after running
->runtime_suspend().
This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to
optionally support enabling wake IRQ after running ->runtime_suspend().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 8651f97bd9 ("PM / cpuidle: System resume hang fix with
cpuidle") that introduced cpuidle pausing during system suspend
did that to work around a platform firmware issue causing systems
to hang during resume if CPUs were allowed to enter idle states
in the system suspend and resume code paths.
However, pausing cpuidle before the last phase of suspending
devices is the source of an otherwise arbitrary difference between
the suspend-to-idle path and other system suspend variants, so it is
cleaner to do that later, before taking secondary CPUs offline (it
is still safer to take secondary CPUs offline with cpuidle paused,
though).
Modify the code accordingly, but in order to avoid code duplication,
introduce new wrapper functions, pm_sleep_disable_secondary_cpus()
and pm_sleep_enable_secondary_cpus(), to combine cpuidle_pause()
and cpuidle_resume(), respectively, with the handling of secondary
CPUs during system-wide transitions to sleep states.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
It is pointless to pause cpuidle in the suspend-to-idle path,
because it is going to be resumed in the same path later and
pausing it does not serve any particular purpose in that case.
Rework the code to avoid doing that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to allow "syscore" devices to runtime-suspend
during system-wide PM transitions, because they are subject to the
same possible failure modes as any other devices in that respect.
Accordingly, change device_prepare() and device_complete() to call
pm_runtime_get_noresume() and pm_runtime_put(), respectively, for
"syscore" devices too.
Fixes: 057d51a126 ("Merge branch 'pm-sleep'")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYUR8DAAKCRCAXGG7T9hj
vjclAP0ekisZSabOsmzM0iz8rpuYj113/kQozokFeFD5eQlEiAD/b5LytLosic/1
5XKa5fbOyimAyRBwblWhpLLhrW6uiAg=
=WoAB
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- The first hunk of a Xen swiotlb fixup series fixing multiple minor
issues and doing some small cleanups
- Some further Xen related fixes avoiding WARN() splats when running as
Xen guests or dom0
- A Kconfig fix allowing the pvcalls frontend to be built as a module
* tag 'for-linus-5.15b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
swiotlb-xen: drop DEFAULT_NSLABS
swiotlb-xen: arrange to have buffer info logged
swiotlb-xen: drop leftover __ref
swiotlb-xen: limit init retries
swiotlb-xen: suppress certain init retries
swiotlb-xen: maintain slab count properly
swiotlb-xen: fix late init retry
swiotlb-xen: avoid double free
xen/pvcalls: backend can be a module
xen: fix usage of pmd_populate in mremap for pv guests
xen: reset legacy rtc flag for PV domU
PM: base: power: don't try to use non-existing RTC for storing data
xen/balloon: use a kernel thread instead a workqueue
If there is no legacy RTC device, don't try to use it for storing trace
data across suspend/resume.
Cc: <stable@vger.kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20210903084937.19392-2-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
There are variables(power.may_skip_resume and dev->power.must_resume)
and DPM_FLAG_MAY_SKIP_RESUME flags to control the resume of devices after
a system wide suspend transition.
Setting the DPM_FLAG_MAY_SKIP_RESUME flag means that the driver allows
its "noirq" and "early" resume callbacks to be skipped if the device
can be left in suspend after a system-wide transition into the working
state. PM core determines that the driver's "noirq" and "early" resume
callbacks should be skipped or not with dev_pm_skip_resume() function by
checking power.may_skip_resume variable.
power.must_resume variable is getting set to false in __device_suspend()
function without checking device's DPM_FLAG_MAY_SKIP_RESUME settings.
In problematic scenario, where all the devices in the suspend_late
stage are successful and some device can fail to suspend in
suspend_noirq phase. So some devices successfully suspended in suspend_late
stage are not getting chance to execute __device_suspend_noirq()
to set dev->power.must_resume variable to true and not getting
resumed in early_resume phase.
Add a check for device's DPM_FLAG_MAY_SKIP_RESUME flag before
setting power.must_resume variable in __device_suspend function.
Fixes: 6e176bf8d4 ("PM: sleep: core: Do not skip callbacks in the resume phase")
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function has the 'irq' parameter which isn't ever used, so drop it.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of data
to describe clks on various SoCs and fix bugs. The other big new thing
in here is the Mediatek MT8192 clk driver. That's been under review for
a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk drivers.
There are some non-clk driver bits in here which have all been acked by
the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML
-----BEGIN PGP SIGNATURE-----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=Rrqg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing changed in the clk framework core this time around. We did get
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of
data to describe clks on various SoCs and fix bugs. The other big new
thing in here is the Mediatek MT8192 clk driver. That's been under
review for a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk
drivers. There are some non-clk driver bits in here which have all
been acked by the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (128 commits)
dt-bindings: clock: samsung: fix header path in example
clk: tegra: fix old-style declaration
clk: qcom: Add SM6350 GCC driver
MAINTAINERS: clock: include S3C and S5P in Samsung SoC clock entry
dt-bindings: clock: samsung: convert S5Pv210 AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos4 to dtschema
dt-bindings: clock: samsung: convert Exynos3250 to dtschema
dt-bindings: clock: samsung: convert Exynos542x to dtschema
dt-bindings: clock: samsung: add bindings for Exynos external clock
dt-bindings: clock: samsung: convert Exynos5250 to dtschema
clk: vc5: Add properties for configuring SD/OE behavior
clk: vc5: Use dev_err_probe
dt-bindings: clk: vc5: Add properties for configuring the SD/OE pin
dt-bindings: clock: brcm,iproc-clocks: fix armpll properties
clk: zynqmp: Fix kernel-doc format
clk: at91: clk-generated: Limit the requested rate to our range
clk: ralink: avoid to set 'CLK_IS_CRITICAL' flag for gates
clk: zynqmp: Fix a memory leak
clk: zynqmp: Check the return type
...
Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did the
following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
The latter one will cause a tiny merge issue with your tree, as there
was a last-minute fix for this in 5.14 in your tree, but the fixup
should be "obvious". If you want me to provide a fixed merge for this,
please let me know.
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs
users at once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
s8VFP1NY2BjmxJbkebLL
=8kVu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
If CONFIG_PM_OPP=n, of_get_required_opp_performance_state() always
returns -EOPNOTSUPP, and all drivers for devices that are part of a PM
Domain fail to probe with:
failed to set required performance state for power-domain foo: -95
probe of bar failed with error -95
Fix this by treating -EOPNOTSUPP the same as -ENODEV.
Fixes: c016baf7dc ("PM: domains: Add support for 'required-opps' to set default perf state")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A typical code pattern for pm_clk_create() call is to call it in the
_probe function and to call pm_clk_destroy() both from _probe error path
and from _remove function. For some drivers the whole remove function
would consist of the call to pm_remove_disable().
Add helper function to replace this bolierplate piece of code. Calling
devm_pm_clk_create() removes the need for calling pm_clk_destroy() both
in the probe()'s error path and in the remove() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210731195034.979084-3-dmitry.baryshkov@linaro.org
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A typical code pattern for pm_runtime_enable() call is to call it in the
_probe function and to call pm_runtime_disable() both from _probe error
path and from _remove function. For some drivers the whole remove
function would consist of the call to pm_remove_disable().
Add helper function to replace this bolierplate piece of code. Calling
devm_pm_runtime_enable() removes the need for calling
pm_runtime_disable() both in the probe()'s error path and in the
remove() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210731195034.979084-2-dmitry.baryshkov@linaro.org
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
GENPD core doesn't support handling performance state changes while
consumer device is runtime-suspended or when runtime PM is disabled.
GENPD core may override performance state that was configured by device
driver while RPM of the device was disabled or device was RPM-suspended.
Let's close that gap by allowing drivers to control performance state
while RPM of a consumer device is disabled and to set up performance
state of RPM-suspended device that will be applied by GENPD core on
RPM-resume of the device.
Fixes: 5937c3ce21 ("PM: domains: Drop/restore performance state votes for devices at runtime PM")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices within power domains with performance states do not
support DVFS, but still need to vote on a default/static state
while they are active. They can express this using the 'required-opps'
property in device tree, which points to the phandle of the OPP
supported by the corresponding power-domains.
Add support to parse this information from DT and then set the
specified performance state during attach and drop it on detach.
runtime suspend/resume callbacks already have logic to drop/set
the vote as needed and should take care of dropping the default
perf state vote on runtime suspend and restore it back on runtime
resume.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpuidle:
cpuidle: qcom: Add SPM register data for MSM8226
dt-bindings: arm: msm: Add SAW2 for MSM8226
* pm-sleep:
PM: sleep: Use ktime_us_delta() in initcall_debug_report()
* pm-domains:
PM: domains: Shrink locking area of the gpd_list_lock
Use ktime_us_delta() to make the debug log more precise instead of
shifting the return value of ktime_to_ns() applied to a ktime_sub()
result by 10 bit positions to the right.
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
[ rjw: Changelog rewrite, subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-core:
PM: runtime: Clarify documentation when callbacks are unassigned
PM: runtime: Allow unassigned ->runtime_suspend|resume callbacks
PM: runtime: Improve path in rpm_idle() when no callback
PM: runtime: document common mistake with pm_runtime_get_sync()
* pm-sleep:
PM: hibernate: remove leading spaces before tabs
PM: sleep: remove trailing spaces and tabs
PM: hibernate: fix spelling mistakes
PM: wakeirq: Set IRQF_NO_AUTOEN when requesting the IRQ
We are currently allowing ->runtime_idle() callbacks to be unassigned
without returning an error code from rpm_idle(). This has been useful to
avoid boilerplate code in drivers. Let's take this approach a step further,
by allowing also unassigned ->runtime_suspend|resume() callbacks.
In this way, a consumer/supplier device link can be used to let a consumer
device be power managed through its supplier device, without requiring
assigned ->runtime_suspend|resume() callbacks for the consumer device, for
example.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When pm_runtime_no_callbacks() has been called for a struct device to set
the dev->power.no_callbacks flag for it, it enables rpm_idle() to take a
slightly quicker path by assuming that a ->runtime_idle() callback would
have returned 0 to indicate success.
A device that does not have the dev->power.no_callbacks flag set for it,
may still be missing a corresponding ->runtime_idle() callback, in which
case the slower path in rpm_idle() is taken. Let's improve the behaviour
for this case, by aligning code to the quicker path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A subsystem/driver that need to manage OPPs for its device, should
typically drop its vote for the OPP when the device becomes runtime
suspended. In this way, the corresponding aggregation of the performance
state votes that is managed in genpd for the attached PM domain, may find
that the aggregated vote can be decreased. Hence, it may allow genpd to set
the lower performance state for the PM domain, thus avoiding to waste
energy.
To accomplish this, typically a subsystem/driver would need to call
dev_pm_opp_set_rate|opp() for its device from its ->runtime_suspend()
callback, to drop the vote for the OPP. Accordingly, it needs another call
to dev_pm_opp_set_rate|opp() to restore the vote for the OPP from its
->runtime_resume() callback.
To avoid boilerplate code in subsystems/driver to deal with these things,
let's instead manage this internally in genpd.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When dev_pm_genpd_set_performance_state() gets called to set a new
performance state for the device, let's take a quicker path by doing an
early return, if it turns out that the new state is already set for the
device.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To prepare some of the code in dev_pm_genpd_set_performance_state() to be
re-used from subsequent changes, let's split it up into two functions.
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the following make W=1 kernel build warnings:
drivers/base/power/domain_governor.c:259: warning: Function parameter or member 'now' not described in '_default_power_down_ok'
drivers/base/power/domain.c:581: warning: Function parameter or member 'depth' not described in 'genpd_power_off'
drivers/base/power/domain.c:2520: warning: Function parameter or member 'np' not described in 'of_genpd_remove_last'
drivers/base/power/domain.c:2520: warning: Excess function parameter 'provider' description in 'of_genpd_remove_last'
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
request_irq() after setting IRQ_NOAUTOEN as below
irq_set_status_flags(irq, IRQ_NOAUTOEN);
request_irq(dev, irq...);
can be replaced by request_irq() with IRQF_NO_AUTOEN flag.
This change is just to simplify the code, no actual functional
changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As pm_runtime_need_not_resume() relies also on usage_count, it can return
a different value in pm_runtime_force_suspend() compared to when called in
pm_runtime_force_resume(). Different return values can happen if anything
calls PM runtime functions in between, and causes the parent child_count
to increase on every resume.
So far I've seen the issue only for omapdrm that does complicated things
with PM runtime calls during system suspend for legacy reasons:
omap_atomic_commit_tail() for omapdrm.0
dispc_runtime_get()
wakes up 58000000.dss as it's the dispc parent
dispc_runtime_resume()
rpm_resume() increases parent child_count
dispc_runtime_put() won't idle, PM runtime suspend blocked
pm_runtime_force_suspend() for 58000000.dss, !pm_runtime_need_not_resume()
__update_runtime_status()
system suspended
pm_runtime_force_resume() for 58000000.dss, pm_runtime_need_not_resume()
pm_runtime_enable() only called because of pm_runtime_need_not_resume()
omap_atomic_commit_tail() for omapdrm.0
dispc_runtime_get()
wakes up 58000000.dss as it's the dispc parent
dispc_runtime_resume()
rpm_resume() increases parent child_count
dispc_runtime_put() won't idle, PM runtime suspend blocked
...
rpm_suspend for 58000000.dss but parent child_count is now unbalanced
Let's fix the issue by adding a flag for needs_force_resume and use it in
pm_runtime_force_resume() instead of pm_runtime_need_not_resume().
Additionally omapdrm system suspend could be simplified later on to avoid
lots of unnecessary PM runtime calls and the complexity it adds. The
driver can just use internal functions that are shared between the PM
runtime and system suspend related functions.
Fixes: 4918e1f87c ("PM / runtime: Rework pm_runtime_force_suspend/resume()")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The variable retval is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have open coded dev_set_name() implementation, replace that
with a direct call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove make W=1 warning:
drivers/base/power/clock_ops.c:148: warning: expecting prototype for
pm_clk_enable(). Prototype was for __pm_clk_enable() instead
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove make W=1 warnings and fit 'Itereates' typos
drivers/base/power/wakeup.c:403: warning: wrong kernel-doc identifier on line:
* device_wakeup_arm_wake_irqs(void)
drivers/base/power/wakeup.c:419: warning: wrong kernel-doc identifier on line:
* device_wakeup_disarm_wake_irqs(void)
drivers/base/power/wakeup.c:537: warning: Function parameter or member
'enable' not described in 'device_set_wakeup_enable'
drivers/base/power/wakeup.c:592: warning: expecting prototype for
wakup_source_activate(). Prototype was for wakeup_source_activate()
instead
drivers/base/power/wakeup.c:697: warning: expecting prototype for
wakup_source_deactivate(). Prototype was for
wakeup_source_deactivate() instead
drivers/base/power/wakeup.c:795: warning: Function parameter or member
't' not described in 'pm_wakeup_timer_fn'
drivers/base/power/wakeup.c:795: warning: Excess function parameter
'data' description in 'pm_wakeup_timer_fn'
drivers/base/power/wakeup.c:1027: warning: Function parameter or
member 'set' not described in 'pm_wakep_autosleep_enabled'
drivers/base/power/wakeup.c:1027: warning: Excess function parameter
'enabled' description in 'pm_wakep_autosleep_enabled'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
remove make W=1 warnings
drivers/base/power/runtime.c:926: warning: Function parameter or
member 'timer' not described in 'pm_suspend_timer_fn'
drivers/base/power/runtime.c:926: warning: Excess function parameter
'data' description in 'pm_suspend_timer_fn'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pm_runtime_put_suppliers() must not decrement rpm_active unless the
consumer is suspended. That is because, otherwise, it could suspend
suppliers for an active consumer.
That can happen as follows:
static int driver_probe_device(struct device_driver *drv, struct device *dev)
{
int ret = 0;
if (!device_is_registered(dev))
return -ENODEV;
dev->can_match = true;
pr_debug("bus: '%s': %s: matched device %s with driver %s\n",
drv->bus->name, __func__, dev_name(dev), drv->name);
pm_runtime_get_suppliers(dev);
if (dev->parent)
pm_runtime_get_sync(dev->parent);
At this point, dev can runtime suspend so rpm_put_suppliers() can run,
rpm_active becomes 1 (the lowest value).
pm_runtime_barrier(dev);
if (initcall_debug)
ret = really_probe_debug(dev, drv);
else
ret = really_probe(dev, drv);
Probe callback can have runtime resumed dev, and then runtime put
so dev is awaiting autosuspend, but rpm_active is 2.
pm_request_idle(dev);
if (dev->parent)
pm_runtime_put(dev->parent);
pm_runtime_put_suppliers(dev);
Now pm_runtime_put_suppliers() will put the supplier
i.e. rpm_active 2 -> 1, but consumer can still be active.
return ret;
}
Fix by checking the runtime status. For any status other than
RPM_SUSPENDED, rpm_active can be considered to be "owned" by
rpm_[get/put]_suppliers() and pm_runtime_put_suppliers() need do nothing.
Reported-by: Asutosh Das <asutoshd@codeaurora.org>
Fixes: 4c06c4e6cf ("driver core: Fix possible supplier PM-usage counter imbalance")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
rpm_active indicates how many times the supplier usage_count has been
incremented. Consequently it must be updated after pm_runtime_get_sync() of
the supplier, not before.
Fixes: 4c06c4e6cf ("driver core: Fix possible supplier PM-usage counter imbalance")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because the PM-runtime status of the device is not updated in
__rpm_callback(), attempts to suspend the suppliers of the given
device triggered by the rpm_put_suppliers() call in there may
cause a supplier to be suspended completely before the status of
the consumer is updated to RPM_SUSPENDED, which is confusing.
To avoid that (1) modify __rpm_callback() to only decrease the
PM-runtime usage counter of each supplier and (2) make rpm_suspend()
try to suspend the suppliers after changing the consumer's status to
RPM_SUSPENDED, in analogy with the device's parent.
Link: https://lore.kernel.org/linux-pm/CAPDyKFqm06KDw_p8WXsM4dijDbho4bb6T4k50UqqvR1_COsp8g@mail.gmail.com/
Fixes: 21d5c57b37 ("PM / runtime: Use device links")
Reported-by: elaine.zhang <zhangqing@rock-chips.com>
Diagnosed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 44cc89f764 ("PM: runtime: Update device status
before letting suppliers suspend") that introduced a race condition
into __rpm_callback() which allowed a concurrent rpm_resume() to
run and resume the device prematurely after its status had been
changed to RPM_SUSPENDED by __rpm_callback().
Fixes: 44cc89f764 ("PM: runtime: Update device status before letting suppliers suspend")
Link: https://lore.kernel.org/linux-pm/24dfb6fc-5d54-6ee2-9195-26428b7ecf8a@intel.com/
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Runtime resuming a device upfront in the genpd_prepare() callback,
to check if there is a wakeup pending for it, seems like an
unnecessary thing to do.
The PM core already manages these kind of things in a common way in
__device_suspend(), via calling pm_runtime_barrier() and
pm_wakeup_pending().
Therefore, let's simply drop this behaviour from genpd_prepare().
Note that, this change is applicable only for devices that are
attached to a genpd that has the GENPD_FLAG_ACTIVE_WAKEUP set
(Renesas, Mediatek, and Rockchip platforms). Moreover, a driver
that needs to restore power for its device to re-configure it
for a system wakeup, may still call pm_runtime_get_sync(), for
example, to do this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because the PM-runtime status of the device is not updated in
__rpm_callback(), attempts to suspend the suppliers of the given
device triggered by rpm_put_suppliers() called by it may fail.
Fix this by making __rpm_callback() update the device's status to
RPM_SUSPENDED before calling rpm_put_suppliers() if the current
status of the device is RPM_SUSPENDING and the callback just invoked
by it has returned 0 (success).
While at it, modify the code in __rpm_callback() to always check
the device's PM-runtime status under its PM lock.
Link: https://lore.kernel.org/linux-pm/CAPDyKFqm06KDw_p8WXsM4dijDbho4bb6T4k50UqqvR1_COsp8g@mail.gmail.com/
Fixes: 21d5c57b37 ("PM / runtime: Use device links")
Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Diagnosed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Elaine Zhang <zhangiqng@rock-chips.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the "big" driver core and debugfs update for 5.12-rc1
This set of driver core patches caused a bunch of problems in linux-next
for the past few weeks, when Saravana tried to set fw_devlink=on as the
default functionality. This caused a number of systems to stop booting,
and lots of bugs were fixed in this area for almost all of the reported
systems, but this option is not ready to be turned on just yet for the
default operation based on this testing, so I've reverted that change at
the very end so we don't have to worry about regressions in 5.12. We
will try to turn this on for 5.13 if testing goes better over the next
few months.
Other than the fixes caused by the fw_devlink testing in here, there's
not much more:
- debugfs fixes for invalid input into debugfs_lookup()
- kerneldoc cleanups
- warn message if platform drivers return an error on their
remove callback (a futile effort, but good to catch).
All of these have been in linux-next for a while now, and the
regressions have gone away with the revert of the fw_devlink change.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZhzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylS2wCfU28FxDWNwcWhPFVfRT8Mb3OxZ50An1sR4lNR
t5Ie4aztMUjVJhI9bq6g
=3NSB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / debugfs update from Greg KH:
"Here is the "big" driver core and debugfs update for 5.12-rc1
This set of driver core patches caused a bunch of problems in
linux-next for the past few weeks, when Saravana tried to set
fw_devlink=on as the default functionality. This caused a number of
systems to stop booting, and lots of bugs were fixed in this area for
almost all of the reported systems, but this option is not ready to be
turned on just yet for the default operation based on this testing, so
I've reverted that change at the very end so we don't have to worry
about regressions in 5.12
We will try to turn this on for 5.13 if testing goes better over the
next few months.
Other than the fixes caused by the fw_devlink testing in here, there's
not much more:
- debugfs fixes for invalid input into debugfs_lookup()
- kerneldoc cleanups
- warn message if platform drivers return an error on their remove
callback (a futile effort, but good to catch).
All of these have been in linux-next for a while now, and the
regressions have gone away with the revert of the fw_devlink change"
* tag 'driver-core-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Revert "driver core: Set fw_devlink=on by default"
of: property: fw_devlink: Ignore interrupts property for some configs
debugfs: do not attempt to create a new file before the filesystem is initalized
debugfs: be more robust at handling improper input in debugfs_lookup()
driver core: auxiliary bus: Fix calling stage for auxiliary bus init
of: irq: Fix the return value for of_irq_parse_one() stub
of: irq: make a stub for of_irq_parse_one()
clk: Mark fwnodes when their clock provider is added/removed
PM: domains: Mark fwnodes when their powerdomain is added/removed
irqdomain: Mark fwnodes when their irqdomain is added/removed
driver core: fw_devlink: Handle suppliers that don't use driver core
of: property: Add fw_devlink support for optional properties
driver core: Add fw_devlink.strict kernel param
of: property: Don't add links to absent suppliers
driver core: fw_devlink: Detect supplier devices that will never be added
driver core: platform: Emit a warning if a remove callback returned non-zero
of: property: Fix fw_devlink handling of interrupts/interrupts-extended
gpiolib: Don't probe gpio_device if it's not the primary device
device.h: Remove bogus "the" in kerneldoc
gpiolib: Bind gpio_device to a driver to enable fw_devlink=on by default
...
* pm-sleep:
PM: sleep: Constify static struct attribute_group
PM: sleep: Use dev_printk() when possible
PM: sleep: No need to check PF_WQ_WORKER in thaw_kernel_threads()
* pm-core:
PM: runtime: Fix typos and grammar
PM: runtime: Fix resposible -> responsible in runtime.c
* pm-domains:
PM: domains: Simplify the calculation of variables
PM: domains: Add "performance" column to debug summary
PM: domains: Make of_genpd_add_subdomain() return -EPROBE_DEFER
PM: domains: Make set_performance_state() callback optional
PM: domains: use device's next wakeup to determine domain idle state
PM: domains: inform PM domain of a device's next wakeup
* pm-clk:
PM: clk: make PM clock layer compatible with clocks that must sleep
This allows fw_devlink to recognize power domain drivers that don't use
the device-driver model to initialize the device. fw_devlink will use
this information to make sure consumers of such power domain aren't
indefinitely blocked from probing, waiting for the power domain device
to appear and bind to a driver.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210205222644.2357303-8-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following coccicheck warnings:
./drivers/base/power/domain.c:938:31-33: WARNING !A || A && B is
equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Suggested-by: Jiapeng Zhong <oswb@linux.alibaba.com>
Signed-off-by: Abaci Team <abaci-bugfix@linux.alibaba.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The clock API splits its interface into sleepable ant atomic contexts:
- clk_prepare/clk_unprepare for stuff that might sleep
- clk_enable_clk_disable for anything that may be done in atomic context
The code handling runtime PM for clocks only calls clk_disable() on
suspend requests, and clk_enable on resume requests. This means that
runtime PM with clock providers that only have the prepare/unprepare
methods implemented is basically useless.
Many clock implementations can't accommodate atomic contexts. This is
often the case when communication with the clock happens through another
subsystem like I2C or SCMI.
Let's make the clock PM code useful with such clocks by safely invoking
clk_prepare/clk_unprepare upon resume/suspend requests. Of course, when
such clocks are registered with the PM layer then pm_runtime_irq_safe()
can't be used, and neither pm_runtime_suspend() nor pm_runtime_resume()
may be invoked in atomic context.
For clocks that do implement the enable and disable methods then
everything just works as before.
A note on sparse:
According to https://lwn.net/Articles/109066/ there are things
that sparse can't cope with. In particular, pm_clk_op_lock() and
pm_clk_op_unlock() may or may not lock/unlock psd->lock depending on
some runtime condition. To work around that we tell it the lock is
always untaken for the purpose of static analisys.
Thanks to Naresh Kamboju for reporting issues with the initial patch.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use dev_printk() when possible to make messages more consistent with other
device-related messages.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add "performance" column to debug summary which shows performance state
of all power domains and theirs devices.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
[tested on NVIDIA Tegra20/30/124 SoCs]
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Driver of a power domain provider may not be ready at the time of
of_genpd_add_subdomain() invocation. Make this function to return
-EPROBE_DEFER instead of -ENOENT in order to remove a need from
power domain drivers to handle the error code specially.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
[tested on NVIDIA Tegra20/30/124 SoCs]
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make set_performance_state() callback optional in order to remove the
need from power domain drivers to implement a dummy callback. If callback
isn't implemented by a GENPD driver, then the performance state is passed
to the parent domain.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
[tested on NVIDIA Tegra20/30/124 SoCs]
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, a PM domain's idle state is determined based on whether the
QoS requirements are met. However, even entering an idle state may waste
power if the minimum residency requirements aren't fulfilled.
CPU PM domains use the next timer wakeup for the CPUs in the domain to
determine the sleep duration of the domain. This is compared with the
idle state residencies to determine the optimal idle state. For other PM
domains, determining the sleep length is not that straight forward. But
if the device's next_event is available, we can use that to determine
the sleep duration of the PM domain.
Let's update the domain governor logic to check for idle state residency
based on the next wakeup of devices as well as QoS constraints. But
since, not all domains may contain devices capable of specifying the
next wakeup, let's enable this additional check only if specified by the
domain's flags when initializing the domain.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices may have a predictable interrupt pattern while executing
usecases. An example would be the VSYNC interrupt associated with
display devices. A 60 Hz display could cause a interrupt every 16 ms. If
the device were in a PM domain, the domain would need to be powered up
for device to resume and handle the interrupt.
Entering a domain idle state saves power, only if the residency of the
idle state is met. Without knowing the idle duration of the domain, the
governor would just choose the deepest idle state that matches the QoS
requirements. The domain might be powered off just as the device is
expecting to wake up. If devices could inform PM frameworks of their
next event, the parent PM domain's idle duration can be determined.
So let's add the dev_pm_genpd_set_next_wakeup() API for the device to
inform PM domains of the impending wakeup. This information will be the
domain governor to determine the best idle state given the wakeup.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-sleep:
PM: sleep: Add dev_wakeup_path() helper
PM / suspend: fix kernel-doc markup
PM: sleep: Print driver flags for all devices during suspend/resume
* pm-acpi:
PM: ACPI: Refresh wakeup device power configuration every time
PM: ACPI: PCI: Drop acpi_pm_set_bridge_wakeup()
PM: ACPI: reboot: Use S5 for reboot
* pm-domains:
PM: domains: create debugfs nodes when adding power domains
PM: domains: replace -ENOTSUPP with -EOPNOTSUPP
* powercap:
powercap: Adjust printing the constraint name with new line
powercap: RAPL: Add AMD Fam19h RAPL support
powercap: Add AMD Fam17h RAPL support
powercap/intel_rapl_msr: Convert rapl_msr_priv into pointer
x86/msr-index: sort AMD RAPL MSRs by address
* pm-cpuidle:
cpuidle: Select polling interval based on a c-state with a longer target residency
cpuidle: psci: Enable suspend-to-idle for PSCI OSI mode
PM: domains: Enable dev_pm_genpd_suspend|resume() for suspend-to-idle
PM: domains: Rename pm_genpd_syscore_poweroff|poweron()
* pm-em:
PM / EM: Micro optimization in em_cpu_energy
PM: EM: Update Energy Model with new flag indicating power scale
PM: EM: update the comments related to power scale
PM: EM: Clarify abstract scale usage for power values in Energy Model
Pull OPP (Operating Performance Points) updates for 5.11-rc1 from
Viresh Kumar:
"This contains the following updates:
- Allow empty (node-less) OPP tables in DT for passing just the
dependency related information (Nicola Mazzucato).
- Fix a potential lockdep in OPP core and other OPP core cleanups
(Viresh Kumar).
- Don't abuse dev_pm_opp_get_opp_table() to create an OPP table, fix
cpufreq-dt driver for the same (Viresh Kumar).
- dev_pm_opp_put_regulators() accepts a NULL argument now, updates to
all the users as well (Viresh Kumar)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
opp: Don't return opp_dev from _find_opp_dev()
opp: Allocate the OPP table outside of opp_table_lock
opp: Always add entries in dev_list with opp_table->lock held
debugfs nodes were created in genpd_debug_init alled in late_initcall
preventing power domains registered though loadable modules to have
a debugfs entry.
Create/remove debugfs nodes when the power domain is added/removed
to/from the internal gpd_list.
Signed-off-by: Thierry Strudel <tstrudel@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It has been found that some users (like cpufreq-dt and others on LKML)
have abused the helper dev_pm_opp_get_opp_table() to create the OPP
table instead of just finding it, which is the wrong thing to do. This
routine was meant for OPP core's internal working and exposed the whole
functionality by mistake.
Change the scope of dev_pm_opp_get_opp_table() to only finding the
table. The internal helpers _opp_get_opp_table*() are thus renamed to
_add_opp_table*(), dev_pm_opp_get_opp_table_indexed() is removed (as we
don't need the index field for finding the OPP table) and so the only
user, genpd, is updated.
Note that the prototype of _add_opp_table() was already left in opp.h by
mistake when it was removed earlier and so we weren't required to add it
now.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add dev_wakeup_path() helper to avoid to spread
dev->power.wakeup_path test in drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dev_pm_genpd_suspend|resume() have so far only been used during the
syscore suspend/resume phases. However, during suspend-to-idle, where the
syscore phases doesn't exist, similar operations are sometimes needed.
An existing example are the timekeeping_suspend|resume() functions, which
are being called both through a registered syscore ops during the syscore
phases, but also as regular functions calls from cpuidle (via
tick_freeze()) during suspend-to-idle.
For similar reasons, let's enable the dev_pm_genpd_suspend|resume() APIs to
be re-used for corresponding CPU devices that are attached to a genpd,
during suspend-to-idle.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To better describe what the pm_genpd_syscore_poweroff|poweron() functions
actually do, let's rename them to dev_pm_genpd_suspend|resume() and update
the rather few callers of them accordingly (a couple of clocksource
drivers).
Moreover, let's take the opportunity to add some documentation of these
exported functions, as that is currently missing.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently there are 4 driver flags to control system suspend/resume
behavior: DPM_FLAG_NO_DIRECT_COMPLETE, DPM_FLAG_SMART_PREPARE,
DPM_FLAG_SMART_SUSPEND and DPM_FLAG_MAY_SKIP_RESUME.
Print these flags during suspend/resume so as to get a brief
understanding of the expected behavior of each device, and to
facilitate suspend/resume debugging/tuning.
To enable this tracing:
echo 'file drivers/base/power/main.c +p' >
/sys/kernel/debug/dynamic_debug/control
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit d12544fb2a ("PM: runtime: Remove link state checks in
rpm_get/put_supplier()") nothing prevents the consumer device's
runtime PM from acquiring additional references to the supplier
device after pm_runtime_clean_up_links() has run (or even while it
is running), so calling this function from __device_release_driver()
may be pointless (or even harmful).
Moreover, it ignores stateless device links, so the runtime PM
handling of managed and stateless device links is inconsistent
because of it, so better get rid of it entirely.
Fixes: d12544fb2a ("PM: runtime: Remove link state checks in rpm_get/put_supplier()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While removing a device link, drop the supplier device's runtime PM
usage counter as many times as needed to drop all of the runtime PM
references to it from the consumer in addition to dropping the
consumer's link count.
Fixes: baa8809f60 ("PM / runtime: Optimize the use of device links")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Move the AVS drivers to new platform-specific locations and get
rid of the drivers/power/avs directory (Ulf Hansson).
- Add on/off notifiers and idle state accounting support to the
generic power domains (genpd) framework (Ulf Hansson, Lina Iyer).
- Ulf will maintain the PM domain part of cpuidle-psci (Ulf Hansson).
- Make intel_idle disregard ACPI _CST if it cannot use the data
returned by that method (Mel Gorman).
- Modify intel_pstate to avoid leaving useless sysfs directory
structure behind if it cannot be registered (Chen Yu).
- Fix domain detection in the RAPL power capping driver and prevent
it from failing to enumerate the Psys RAPL domain (Zhang Rui).
- Allow acpi-cpufreq to use ACPI _PSD information with Family 19 and
later AMD chips (Wei Huang).
- Update the driver assumptions comment in intel_idle and fix a
kerneldoc comment in the runtime PM framework (Alexander Monakov,
Bean Huo).
- Avoid unnecessary resets of the cached frequency in the schedutil
cpufreq governor to reduce overhead (Wei Wang).
- Clean up the cpufreq core a bit (Viresh Kumar).
- Make assorted minor janitorial changes (Daniel Lezcano, Geert
Uytterhoeven, Hubert Jasudowicz, Tom Rix).
- Clean up and optimize the cpupower utility somewhat (Colin Ian
King, Martin Kaistra).
-----BEGIN PGP SIGNATURE-----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=TFKg
-----END PGP SIGNATURE-----
Merge tag 'pm-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"First of all, the adaptive voltage scaling (AVS) drivers go to new
platform-specific locations as planned (this part was reported to have
merge conflicts against the new arm-soc updates in linux-next).
In addition to that, there are some fixes (intel_idle, intel_pstate,
RAPL, acpi_cpufreq), the addition of on/off notifiers and idle state
accounting support to the generic power domains (genpd) code and some
janitorial changes all over.
Specifics:
- Move the AVS drivers to new platform-specific locations and get rid
of the drivers/power/avs directory (Ulf Hansson).
- Add on/off notifiers and idle state accounting support to the
generic power domains (genpd) framework (Ulf Hansson, Lina Iyer).
- Ulf will maintain the PM domain part of cpuidle-psci (Ulf Hansson).
- Make intel_idle disregard ACPI _CST if it cannot use the data
returned by that method (Mel Gorman).
- Modify intel_pstate to avoid leaving useless sysfs directory
structure behind if it cannot be registered (Chen Yu).
- Fix domain detection in the RAPL power capping driver and prevent
it from failing to enumerate the Psys RAPL domain (Zhang Rui).
- Allow acpi-cpufreq to use ACPI _PSD information with Family 19 and
later AMD chips (Wei Huang).
- Update the driver assumptions comment in intel_idle and fix a
kerneldoc comment in the runtime PM framework (Alexander Monakov,
Bean Huo).
- Avoid unnecessary resets of the cached frequency in the schedutil
cpufreq governor to reduce overhead (Wei Wang).
- Clean up the cpufreq core a bit (Viresh Kumar).
- Make assorted minor janitorial changes (Daniel Lezcano, Geert
Uytterhoeven, Hubert Jasudowicz, Tom Rix).
- Clean up and optimize the cpupower utility somewhat (Colin Ian
King, Martin Kaistra)"
* tag 'pm-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
PM: sleep: remove unreachable break
PM: AVS: Drop the avs directory and the corresponding Kconfig
PM: AVS: qcom-cpr: Move the driver to the qcom specific drivers
PM: runtime: Fix typo in pm_runtime_set_active() helper comment
PM: domains: Fix build error for genpd notifiers
powercap: Fix typo in Kconfig "Plance" -> "Plane"
cpufreq: schedutil: restore cached freq when next_f is not changed
acpi-cpufreq: Honor _PSD table setting on new AMD CPUs
PM: AVS: smartreflex Move driver to soc specific drivers
PM: AVS: rockchip-io: Move the driver to the rockchip specific drivers
PM: domains: enable domain idle state accounting
PM: domains: Add curly braces to delimit comment + statement block
PM: domains: Add support for PM domain on/off notifiers for genpd
powercap/intel_rapl: enumerate Psys RAPL domain together with package RAPL domain
powercap/intel_rapl: Fix domain detection
intel_idle: Ignore _CST if control cannot be taken from the platform
cpuidle: Remove pointless stub
intel_idle: mention assumption that WBINVD is not needed
MAINTAINERS: Add section for cpuidle-psci PM domain
cpufreq: intel_pstate: Delete intel_pstate sysfs if failed to register the driver
...
A break following a return statement is pointless, so drop it.
Signed-off-by: Tom Rix <trix@redhat.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The __raw_notifier_call_chain() was recently removed and replaced with
raw_notifier_call_chain_robust(). Recent changes to genpd didn't take that
into account, which causes a build error. Let's fix this by converting to
the raw_notifier_call_chain_robust() in genpd.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To enable better debug of PM domains, keep a track of successful
and failing attempts to enter each domain idle state.
This statistics are exported in debugfs when reading the
idle_states node associated with each PM domain.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is not strict need to group a comment and a single statement in an
if block, as comments are stripped by the pre-processor. However,
adding curly braces does make the code easier to read, and may avoid
mistakes when changing the code later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A device may have specific HW constraints that must be obeyed to, before
its corresponding PM domain (genpd) can be powered off - and vice verse at
power on. These constraints can't be managed through the regular runtime PM
based deployment for a device, because the access pattern for it, isn't
always request based. In other words, using the runtime PM callbacks to
deal with the constraints doesn't work for these cases.
For these reasons, let's instead add a PM domain power on/off notification
mechanism to genpd. To add/remove a notifier for a device, the device must
already have been attached to the genpd, which also means that it needs to
be a part of the PM domain topology.
To add/remove a notifier, let's introduce two genpd specific functions:
- dev_pm_genpd_add|remove_notifier()
Note that, to further clarify when genpd power on/off notifiers may be
used, one can compare with the existing CPU_CLUSTER_PM_ENTER|EXIT
notifiers. In the long run, the genpd power on/off notifiers should be able
to replace them, but that requires additional genpd based platform support
for the current users.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the "big" set of driver core patches for 5.10-rc1
They include a lot of different things, all related to the driver core
and/or some driver logic:
- sysfs common write functions to make it easier to audit sysfs
attributes
- device connection cleanups and fixes
- devm helpers for a few functions
- NOIO allocations for when devices are being removed
- minor cleanups and fixes
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4c4yA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylS7gCfcS+7/PE42eXxMY0z8rBX8aDMadIAn2DVEghA
Eoh9UoMEW4g1uMKORA0c
=CVAW
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.10-rc1
They include a lot of different things, all related to the driver core
and/or some driver logic:
- sysfs common write functions to make it easier to audit sysfs
attributes
- device connection cleanups and fixes
- devm helpers for a few functions
- NOIO allocations for when devices are being removed
- minor cleanups and fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (31 commits)
regmap: debugfs: use semicolons rather than commas to separate statements
platform/x86: intel_pmc_core: do not create a static struct device
drivers core: node: Use a more typical macro definition style for ACCESS_ATTR
drivers core: Use sysfs_emit for shared_cpu_map_show and shared_cpu_list_show
mm: and drivers core: Convert hugetlb_report_node_meminfo to sysfs_emit
drivers core: Miscellaneous changes for sysfs_emit
drivers core: Reindent a couple uses around sysfs_emit
drivers core: Remove strcat uses around sysfs_emit and neaten
drivers core: Use sysfs_emit and sysfs_emit_at for show(device *...) functions
sysfs: Add sysfs_emit and sysfs_emit_at to format sysfs output
dyndbg: use keyword, arg varnames for query term pairs
driver core: force NOIO allocations during unplug
platform_device: switch to simpler IDA interface
driver core: platform: Document return type of more functions
Revert "driver core: Annotate dev_err_probe() with __must_check"
Revert "test_firmware: Test platform fw loading on non-EFI systems"
iio: adc: xilinx-xadc: use devm_krealloc()
hwmon: pmbus: use more devres helpers
devres: provide devm_krealloc()
syscore: Use pm_pr_dbg() for syscore_{suspend,resume}()
...
* pm-core:
PM: runtime: Fix timer_expires data type on 32-bit arches
PM: runtime: Remove link state checks in rpm_get/put_supplier()
* pm-sleep:
ACPI: EC: PM: Drop ec_no_wakeup check from acpi_ec_dispatch_gpe()
ACPI: EC: PM: Flush EC work unconditionally after wakeup
PM: hibernate: remove the bogus call to get_gendisk() in software_resume()
PM: hibernate: Batch hibernate and resume IO requests
* pm-pci:
PCI/ACPI: Whitelist hotplug ports for D3 if power managed by ACPI
* pm-domains:
PM: domains: Allow to abort power off when no ->power_off() callback
PM: domains: Rename power state enums for genpd
Pull opertaing performance points (OPP) framework fixes for 5.10-rc1
from Viresh Kumar:
"- Return -EPROBE_DEFER properly from dev_pm_opp_get_opp_table()
(Stephan Gerhold).
- Minor cleanups around required-opps (Stephan Gerhold).
- Extends opp-supported-hw property to contain multiple versions
(Viresh Kumar).
- Multiple cleanups around dev_pm_opp_attach_genpd() (Viresh Kumar).
- Multiple fixes, cleanups in the OPP core for overall better design
(Viresh Kumar)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Allow opp-level to be set to 0
opp: Prevent memory leak in dev_pm_opp_attach_genpd()
ARM: tegra: Pass multiple versions in opp-supported-hw property
opp: Allow opp-supported-hw to contain multiple versions
dt-bindings: opp: Allow opp-supported-hw to contain multiple versions
opp: Set required OPPs in reverse order when scaling down
opp: Reduce code duplication in _set_required_opps()
opp: Drop unnecessary check from dev_pm_opp_attach_genpd()
opp: Handle multiple calls for same OPP table in _of_add_opp_table_v1()
opp: Allow dev_pm_opp_get_opp_table() to return -EPROBE_DEFER
opp: Remove _dev_pm_opp_find_and_remove_table() wrapper
opp: Split out _opp_set_rate_zero()
opp: Reuse the enabled flag in !target_freq path
opp: Rename regulator_enabled and use it as status of all resources
In genpd_power_off() we may decide to abort the power off of the PM domain,
even beyond the point when the governor would accept it. The abort is done
if it turns out that a child domain has been requested to be powered on,
which means it's waiting for the lock of the parent to be released.
However, the abort is currently only considered if the genpd in question
has a ->power_off() callback assigned. This is unnecessary limiting,
especially if the genpd would have a parent of its own. Let's remove the
limitation and make the behaviour consistent.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To clarify the code a bit, let's rename GPD_STATE_ACTIVE into
GENPD_STATE_ON and GPD_STATE_POWER_OFF to GENPD_STATE_OFF.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change additional instances that could use sysfs_emit and sysfs_emit_at
that the coccinelle script could not convert.
o macros creating show functions with ## concatenation
o unbound sprintf uses with buf+len for start of output to sysfs_emit_at
o returns with ?: tests and sprintf to sysfs_emit
o sysfs output with struct class * not struct device * arguments
Miscellanea:
o remove unnecessary initializations around these changes
o consistently use int len for return length of show functions
o use octal permissions and not S_<FOO>
o rename a few show function names so DEVICE_ATTR_<FOO> can be used
o use DEVICE_ATTR_ADMIN_RO where appropriate
o consistently use const char *output for strings
o checkpatch/style neatening
Signed-off-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/8bc24444fe2049a9b2de6127389b57edfdfe324d.1600285923.git.joe@perches.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strcat is no longer necessary for sysfs_emit and sysfs_emit_at uses.
Convert the strcat uses to sysfs_emit calls and neaten other block
uses of direct returns to use an intermediate const char *.
Signed-off-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/5d606519698ce4c8f1203a2b35797d8254c6050a.1600285923.git.joe@perches.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support runtime PM for hisi SAS driver (the driver is in directory
drivers/scsi/hisi_sas), we add device link between scsi_device->sdev_gendev
(consumer device) and hisi_hba->dev(supplier device) with flags
DL_FLAG_PM_RUNTIME | DL_FLAG_RPM_ACTIVE.
After runtime suspended consumers and supplier, unload the dirver which
causes a hung.
We found that it called function device_release_driver_internal() to
release the supplier device (hisi_hba->dev), as the device link was
busy, it set the device link state to DL_STATE_SUPPLIER_UNBIND, and
then it called device_release_driver_internal() to release the consumer
device (scsi_device->sdev_gendev).
Then it would try to call pm_runtime_get_sync() to resume the consumer
device, but because consumer-supplier relation existed, it would try
to resume the supplier first, but as the link state was already
DL_STATE_SUPPLIER_UNBIND, so it skipped resuming the supplier and only
resumed the consumer which hanged (it sends IOs to resume scsi_device
while the SAS controller is suspended).
Simple flow is as follows:
device_release_driver_internal -> (supplier device)
if device_links_busy ->
device_links_unbind_consumers ->
...
WRITE_ONCE(link->status, DL_STATE_SUPPLIER_UNBIND)
device_release_driver_internal (consumer device)
pm_runtime_get_sync -> (consumer device)
...
__rpm_callback ->
rpm_get_suppliers ->
if link->state == DL_STATE_SUPPLIER_UNBIND -> skip the action of resuming the supplier
...
pm_runtime_clean_up_links
...
Correct suspend/resume ordering between a supplier device and its consumer
devices (resume the supplier device before resuming consumer devices, and
suspend consumer devices before suspending the supplier device) should be
guaranteed by runtime PM, but the state checks in rpm_get_supplier() and
rpm_put_supplier() break this rule, so remove them.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
[ rjw: Subject and changelog edits ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It has been reported that system-wide suspend may be aborted in the
absence of any wakeup events due to unforseen interactions of it with
the runtume PM framework.
One failing scenario is when there are multiple devices sharing an
ACPI power resource and runtime-resume needs to be carried out for
one of them during system-wide suspend (for example, because it needs
to be reconfigured before the whole system goes to sleep). In that
case, the runtime-resume of that device involves turning the ACPI
power resource "on" which in turn causes runtime-resume requests
to be queued up for all of the other devices sharing it. Those
requests go to the runtime PM workqueue which is frozen during
system-wide suspend, so they are not actually taken care of until
the resume of the whole system, but the pm_runtime_barrier()
call in __device_suspend() sees them and triggers system wakeup
events for them which then cause the system-wide suspend to be
aborted if wakeup source objects are in active use.
Of course, the logic that leads to triggering those wakeup events is
questionable in the first place, because clearly there are cases in
which a pending runtime resume request for a device is not connected
to any real wakeup events in any way (like the one above). Moreover,
it is racy, because the device may be resuming already by the time
the pm_runtime_barrier() runs and so if the driver doesn't take care
of signaling the wakeup event as appropriate, it will be lost.
However, if the driver does take care of that, the extra
pm_wakeup_event() call in the core is redundant.
Accordingly, drop the conditional pm_wakeup_event() call fron
__device_suspend() and make the latter call pm_runtime_barrier()
alone. Also modify the comment next to that call to reflect the new
code and extend it to mention the need to avoid unwanted interactions
between runtime PM and system-wide device suspend callbacks.
Fixes: 1e2ef05bb8 ("PM: Limit race conditions between runtime PM and system sleep (v2)")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Cc: All applicable <stable@vger.kernel.org>
The OPP core manages various resources, e.g. clocks or interconnect paths.
These resources are looked up when the OPP table is allocated once
dev_pm_opp_get_opp_table() is called the first time (either directly
or indirectly through one of the many helper functions).
At this point, the resources may not be available yet, i.e. looking them
up will result in -EPROBE_DEFER. Unfortunately, dev_pm_opp_get_opp_table()
is currently unable to propagate this error code since it only returns
the allocated OPP table or NULL.
This means that all consumers of the OPP core are required to make sure
that all necessary resources are available. Usually this happens by
requesting them, checking the result and releasing them immediately after.
For example, we have added "dev_pm_opp_of_find_icc_paths(dev, NULL)" to
several drivers now just to make sure the interconnect providers are
ready before the OPP table is allocated. If this call is missing,
the OPP core will only warn about this and then attempt to continue
without interconnect. This will eventually fail horribly, e.g.:
cpu cpu0: _allocate_opp_table: Error finding interconnect paths: -517
... later ...
of: _read_bw: Mismatch between opp-peak-kBps and paths (1 0)
cpu cpu0: _opp_add_static_v2: opp key field not found
cpu cpu0: _of_add_opp_table_v2: Failed to add OPP, -22
This example happens when trying to use interconnects for a CPU OPP
table together with qcom-cpufreq-nvmem.c. qcom-cpufreq-nvmem calls
dev_pm_opp_set_supported_hw(), which ends up allocating the OPP table
early. To fix the problem with the current approach we would need to add
yet another call to dev_pm_opp_of_find_icc_paths(dev, NULL).
But actually qcom-cpufreq-nvmem.c has nothing to do with interconnects...
This commit attempts to make this more robust by allowing
dev_pm_opp_get_opp_table() to return an error pointer. Fixing all
the usages is trivial because the function is usually used indirectly
through another helper (e.g. dev_pm_opp_set_supported_hw() above).
These other helpers already return an error pointer.
The example above then works correctly because set_supported_hw() will
return -EPROBE_DEFER, and qcom-cpufreq-nvmem.c already propagates that
error. It should also be possible to remove the remaining usages of
"dev_pm_opp_of_find_icc_paths(dev, NULL)" from other drivers as well.
Note that this commit currently only handles -EPROBE_DEFER for the
clock/interconnects within _allocate_opp_table(). Other errors are just
ignored as before. Eventually those should be propagated as well.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ Viresh: skip checking return value of dev_pm_opp_get_opp_table() for
EPROBE_DEFER in domain.c, fix NULL return value and reorder
code a bit in core.c, and update exynos-asv.c ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The kerneldoc comment of pm_runtime_get_if_active() doesn't list the
second argument of the function properly, so fix that and while at it
clarify that comment somewhat and add some markup to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
* pm-sleep:
PM: sleep: spread "const char *" correctness
PM: hibernate: fix white space in a few places
freezer: Add unsafe version of freezable_schedule_timeout_interruptible() for NFS
PM: sleep: core: Emit changed uevent on wakeup_sysfs_add/remove
* pm-domains:
PM: domains: Restore comment indentation for generic_pm_domain.child_links
PM: domains: Fix up terminology with parent/child
* powercap:
powercap: Add Power Limit4 support
powercap: idle_inject: Replace play_idle() with play_idle_precise() in comments
powercap: intel_rapl: add support for Sapphire Rapids
* pm-tools:
pm-graph v5.7 - important s2idle fixes
cpupower: Replace HTTP links with HTTPS ones
cpupower: Fix NULL but dereferenced coccicheck errors
cpupower: Fix comparing pointer to 0 coccicheck warns
Udev rules that depend on the power/wakeup attribute don't get triggered
correctly if device_set_wakeup_capable is called after the device is
created. This can happen for several reasons (driver sets wakeup after
device is created, wakeup is changed on parent device, etc) and it seems
reasonable to emit a changed event when adding or removing attributes on
the device.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The genpd infrastructure uses the terms master/slave, but such uses have
no external exposures (not even in Documentation/driver-api/pm/*) and are
not mandated by nor associated with any external specifications. Change
the language used through-out to parent/child.
There was one possible exception in the debugfs node
"pm_genpd/pm_genpd_summary" but its path has no hits outside of the
kernel itself when performing a code search[1], and it seems even this
single usage has been non-functional since it was introduced due to a
typo in the Python ("apend" instead of correct "append"). Fix the typo
while we're at it.
Link: https://codesearch.debian.net/ # [1]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'early_resume_init()' and 'late_resume_init() 'are only called respectively
via 'early_resume_init' and 'late_resume_init'.
They can be marked as __init to save a few bytes of memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now the last users of show_stack() got converted to use an explicit log
level, show_stack_loglvl() can drop it's redundant suffix and become once
again well known show_stack().
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20200418201944.482088-51-dima@arista.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aligning with other watchdog messages just before panic - use KERN_EMERG.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Link: http://lkml.kernel.org/r/20200418201944.482088-47-dima@arista.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of pm_runtime_callbacks_present() is confusing, because
it suggests that the device has PM-runtime callbacks if 'true' is
returned by that function, but in fact that may not be the case,
so replace it with pm_runtime_has_no_callbacks() which is not
ambiguous.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
rpm_suspend() simple bails out when conditions are wrong. But this is not
immediately obvious from the code. Make it clear what we do when conditions
are wrong in rpm_suspend().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename DPM_FLAG_LEAVE_SUSPENDED to DPM_FLAG_MAY_SKIP_RESUME which
matches its purpose more closely.
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Rename DPM_FLAG_NEVER_SKIP to DPM_FLAG_NO_DIRECT_COMPLETE which
matches its purpose more closely.
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # for PCI parts
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Because all callers of dev_pm_smart_suspend_and_suspended use it only
for checking whether or not to skip driver suspend callbacks for a
device, rename it to dev_pm_skip_suspend() in analogy with
dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The name of dev_pm_may_skip_resume() may be easily confused with the
power.may_skip_resume flag which is not checked by that function, so
rename the former as dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Because the power.may_skip_resume device status bit is taken
into account in combination with the DPM_FLAG_LEAVE_SUSPENDED
driver flag, it can be set to 'true' for all devices in the
"suspend" phase of a suspend-resume cycle, so do that.
Then, neither the PM core nor the middle-layer (sybsystem) code
handling it needs to set it to 'true' any more and it just has
to be cleared if there is a reason to avoid skipping the "noirq"
and "early" resume callbacks provided by the driver, so update
the code in question accordingly.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The current code in device_resume_noirq() causes the entire early
resume and resume phases of device suspend to be skipped for
devices for which the noirq resume phase have been skipped (due
to the LEAVE_SUSPENDED flag being set) on the premise that those
devices should stay in runtime-suspend after system-wide resume.
However, that may not be correct in two situations. First, the
middle layer (subsystem) noirq resume callback may be missing for
a given device, but its early resume callback may be present and it
may need to do something even if it decides to skip the driver
callback. Second, if the device's wakeup settings were adjusted
in the suspend phase without resuming the device (that was in
runtime suspend at that time), they most likely need to be
adjusted again in the resume phase and so the driver callback
in that phase needs to be run.
For the above reason, modify the core to allow the middle layer
->resume_late callback to run even if its ->resume_noirq callback
is missing (and the core has skipped the driver-level callback
in that phase) and to allow all device callbacks to run in the
resume phase. Also make the core set the PM-runtime status of
devices with SMART_SUSPEND set whose resume callbacks are not
skipped to "active" in the "noirq" resume phase and update the
affected subsystems (PCI and ACPI) accordingly.
After this change, middle-layer (subsystem) callbacks will always
be invoked in all phases of system suspend and resume and driver
callbacks will always run in the prepare, suspend, resume, and
complete phases for all devices.
For devices with SMART_SUSPEND set, driver callbacks will be
skipped in the late and noirq phases of system suspend if those
devices remain in runtime suspend in __device_suspend_late().
Driver callbacks will also be skipped for them during the
noirq and early phases of the "thaw" transition related to
hibernation in that case.
Setting LEAVE_SUSPENDED means that the driver allows its callbacks
to be skipped in the noirq and early phases of system resume, but
some additional conditions need to be met for that to happen (among
other things, the power.may_skip_resume flag needs to be set for the
device during system suspend for the driver callbacks to be skipped
during the subsequent resume transition).
For all devices with SMART_SUSPEND set whose driver callbacks are
invoked during system resume, the PM-runtime status will be set to
"active" (by the core).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 8b9ec6b732 ("PM core: Use new async_schedule_dev command")
introduced a new function for better performance.
However commit f2a424f6c6 ("PM / core: Introduce dpm_async_fn()
helper") went back to the non-optimized version, async_schedule().
So switch back to the sync_schedule_dev() to improve performance
Fixes: f2a424f6c6 ("PM / core: Introduce dpm_async_fn() helper")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fold four functions in the PM core that each have only one caller
now into their callers.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The code to handle the SMART_SUSPEND driver PM flag is hard to follow
and somewhat inconsistent with respect to devices without middle-layer
(subsystem) callbacks.
Namely, for those devices the core takes the role of a middle layer
in providing the expected ordering of execution of callbacks (under
the assumption that the drivers setting SMART_SUSPEND can reuse their
PM-runtime callbacks directly for system-wide suspend). To that end,
it prevents driver ->suspend_late and ->suspend_noirq callbacks from
being executed for devices that are still runtime-suspended in
__device_suspend_late(), because running the same callback funtion
that was previously run by PM-runtime for them may be invalid.
However, it does that only for devices without any middle-layer
callbacks for the late/noirq/early suspend/resume phases even
though it would be simpler and more consistent to skip the
driver-lavel callbacks for all devices with SMART_SUSPEND set
that are runtime-suspended in __device_suspend_late().
Simplify the code in accordance with the above observation.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
- Fix corner-case suspend-to-idle wakeup issue on systems where
the ACPI SCI is shared with another wakeup source (Hans de Goede).
- Add document describing system-wide suspend and resume code flows
to the admin guide (Rafael Wysocki).
- Add kernel command line option to set pm_debug_messages (Chen Yu).
- Choose schedutil as the preferred scaling governor by default on
ARM big.LITTLE systems and on x86 systems using the intel_pstate
driver in the passive mode (Linus Walleij, Rafael Wysocki).
- Drop racy and redundant checks from the PM core's device_prepare()
routine (Rafael Wysocki).
- Make resume from hibernation take the hibernation_restore() return
value into account (Dexuan Cui).
-----BEGIN PGP SIGNATURE-----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=QFDr
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"Additional power management updates.
These fix a corner-case suspend-to-idle wakeup issue on systems where
the ACPI SCI is shared with another wakeup source, add a kernel
command line option to set pm_debug_messages via the kernel command
line, add a document desctibing system-wide suspend and resume code
flows, modify cpufreq Kconfig to choose schedutil as the preferred
governor by default in a couple of cases and do some assorted
cleanups.
Specifics:
- Fix corner-case suspend-to-idle wakeup issue on systems where the
ACPI SCI is shared with another wakeup source (Hans de Goede).
- Add document describing system-wide suspend and resume code flows
to the admin guide (Rafael Wysocki).
- Add kernel command line option to set pm_debug_messages (Chen Yu).
- Choose schedutil as the preferred scaling governor by default on
ARM big.LITTLE systems and on x86 systems using the intel_pstate
driver in the passive mode (Linus Walleij, Rafael Wysocki).
- Drop racy and redundant checks from the PM core's device_prepare()
routine (Rafael Wysocki).
- Make resume from hibernation take the hibernation_restore() return
value into account (Dexuan Cui)"
* tag 'pm-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
platform/x86: intel_int0002_vgpio: Use acpi_register_wakeup_handler()
ACPI: PM: Add acpi_[un]register_wakeup_handler()
Documentation: PM: sleep: Document system-wide suspend code flows
cpufreq: Select schedutil when using big.LITTLE
PM: sleep: Add pm_debug_messages kernel command line option
PM: sleep: core: Drop racy and redundant checks from device_prepare()
PM: hibernate: Propagate the return value of hibernation_restore()
cpufreq: intel_pstate: Select schedutil as the default governor
Alan Stern points out that the WARN_ON() check in device_prepare()
is racy (because the PM-runtime API can be disabled briefly for any
device at any time and system suspend can start at any time too) and
the pm_runtime_suspended() check in the computation of the
direct_complete flag value is redundant (because it will be
repeated later anyway).
Drop both these checks accordingly.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Skip wakeup_source_sysfs_remove() to fix a NULL pinter dereference via
ws->dev, if the wakeup source is unregistered before registering the
wakeup class from device_add().
Fixes: 2ca3d1ecb8 ("PM / wakeup: Register wakeup class kobj after device is added")
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
[ rjw: Subject & changelog, white space ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 2c36168480 ("PM / Domains: Don't treat zero found compatible idle
states as an error"), moved of_genpd_parse_idle_states() towards allowing
none compatible idle state to be found for the device node, rather than
returning an error code.
However, it didn't consider that the "domain-idle-states" DT property may
be missing as it's optional, which makes of_count_phandle_with_args() to
return -ENOENT. Let's fix this to make the behaviour consistent.
Fixes: 2c36168480 ("PM / Domains: Don't treat zero found compatible idle states as an error")
Reported-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: 4.20+ <stable@vger.kernel.org> # 4.20+
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pm_runtime_get_if_in_use() bumps up the PM-runtime usage count if it
is not equal to zero and the device's PM-runtime status is 'active'.
This works for drivers that do not use autoidle, but for those that
do, the function returns zero even when the device is active.
In order to maintain sane device state while the device is powered on
in the hope that it'll be needed, pm_runtime_get_if_active(dev, true)
returns a positive value if the device's PM-runtime status is 'active'
when it is called, in which case it also increments the device's usage
count.
If the second argument of pm_runtime_get_if_active() is 'false', the
function behaves just like pm_runtime_get_if_in_use(), so redefine
the latter as a wrapper around the former.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a helper to change the owner of a device's power entries. This
needs to happen when the ownership of a device is changed, e.g. when
moving network devices between network namespaces.
This function will be used to correctly account for ownership changes,
e.g. when moving network devices between network namespaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Prevent cpufreq from creating excessively large stack frames and fix
the handling of devices deleted during system-wide resume in the PM
core (Rafael Wysocki), revert a problematic commit affecting the
cpupower utility and correct its man page (Thomas Renninger,
Brahadambal Srinivasan), and improve the intel_pstate_tracer
utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----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=ctQq
-----END PGP SIGNATURE-----
Merge tag 'pm-5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power manadement updates from Rafael Wysocki:
"Prevent cpufreq from creating excessively large stack frames and fix
the handling of devices deleted during system-wide resume in the PM
core (Rafael Wysocki), revert a problematic commit affecting the
cpupower utility and correct its man page (Thomas Renninger,
Brahadambal Srinivasan), and improve the intel_pstate_tracer utility
(Doug Smythies)"
* tag 'pm-5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power/x86/intel_pstate_tracer: change several graphs to autoscale y-axis
tools/power/x86/intel_pstate_tracer: changes for python 3 compatibility
Correction to manpage of cpupower
cpufreq: Avoid creating excessively large stack frames
PM: core: Fix handling of devices deleted during system-wide resume
cpupower: Revert library ABI changes from commit ae2917093f
This kunit update for Linux 5.6-rc1 consists of:
-- Support for building kunit as a module from Alan Maguire
-- AppArmor KUnit tests for policy unpack from Mike Salvatore
-----BEGIN PGP SIGNATURE-----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=AFO4
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.6-rc1-kunit' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest kunit updates from Shuah Khan:
"This kunit update consists of:
- Support for building kunit as a module from Alan Maguire
- AppArmor KUnit tests for policy unpack from Mike Salvatore"
* tag 'linux-kselftest-5.6-rc1-kunit' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: building kunit as a module breaks allmodconfig
kunit: update documentation to describe module-based build
kunit: allow kunit to be loaded as a module
kunit: remove timeout dependence on sysctl_hung_task_timeout_seconds
kunit: allow kunit tests to be loaded as a module
kunit: hide unexported try-catch interface in try-catch-impl.h
kunit: move string-stream.h to lib/kunit
apparmor: add AppArmor KUnit tests for policy unpack
* pm-core:
PM-runtime: add tracepoints for usage_count changes
* powercap:
powercap/intel_rapl: add support for JasperLake
x86/cpu: Add Jasper Lake to Intel family
powercap/intel_rapl: add support for TigerLake Mobile
* pm-opp:
opp: Replace list_kref with a local counter
opp: Free static OPPs on errors while adding them
* pm-avs:
power: avs: qcom-cpr: remove duplicated include from qcom-cpr.c
power: avs: fix uninitialized error return on failed cpr_read_fuse_uV() call
power: avs: qcom-cpr: make cpr_get_opp_hz_for_req() static
power: avs: qcom-cpr: remove set but unused variable
power: avs: qcom-cpr: make sure that regmap is available
power: avs: qcom-cpr: fix unsigned expression compared with zero
power: avs: qcom-cpr: fix invalid printk specifier in debug print
power: avs: Add support for CPR (Core Power Reduction)
dt-bindings: power: avs: Add support for CPR (Core Power Reduction)
* pm-misc:
mailmap: Add entry for <rjw@sisk.pl>
If a device is deleted by one of its system-wide resume callbacks
(for example, because it does not appear to be present or accessible
any more) along with its children, the resume of the children may
continue leading to use-after-free errors and other issues
(potentially).
Namely, if the device's children are resumed asynchronously, their
resume may have been scheduled already before the device's callback
runs and so the device may be deleted while dpm_wait_for_superior()
is being executed for them. The memory taken up by the parent device
object may be freed then while dpm_wait() is waiting for the parent's
resume callback to complete, which leads to a use-after-free.
Moreover, the resume of the children is really not expected to
continue after they have been unregistered, so it must be terminated
right away in that case.
To address this problem, modify dpm_wait_for_superior() to check
if the target device is still there in the system-wide PM list of
devices and if so, to increment its parent's reference counter, both
under dpm_list_mtx which prevents device_del() running for the child
from dropping the parent's reference counter prematurely.
If the device is not present in the system-wide PM list of devices
any more, the resume of it cannot continue, so check that again after
dpm_wait() returns, which means that the parent's callback has been
completed, and pass the result of that check to the caller of
dpm_wait_for_superior() to allow it to abort the device's resume
if it is not there any more.
Link: https://lore.kernel.org/linux-pm/1579568452-27253-1-git-send-email-chanho.min@lge.com
Reported-by: Chanho Min <chanho.min@lge.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracepoints to remaining places where device's power.usage_count
is changed.
This helps debugging where and why autosuspend is prevented.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As tests are added to kunit, it will become less feasible to execute
all built tests together. By supporting modular tests we provide
a simple way to do selective execution on a running system; specifying
CONFIG_KUNIT=y
CONFIG_KUNIT_EXAMPLE_TEST=m
...means we can simply "insmod example-test.ko" to run the tests.
To achieve this we need to do the following:
o export the required symbols in kunit
o string-stream tests utilize non-exported symbols so for now we skip
building them when CONFIG_KUNIT_TEST=m.
o drivers/base/power/qos-test.c contains a few unexported interface
references, namely freq_qos_read_value() and freq_constraints_init().
Both of these could be potentially defined as static inline functions
in include/linux/pm_qos.h, but for now we simply avoid supporting
module build for that test suite.
o support a new way of declaring test suites. Because a module cannot
do multiple late_initcall()s, we provide a kunit_test_suites() macro
to declare multiple suites within the same module at once.
o some test module names would have been too general ("test-test"
and "example-test" for kunit tests, "inode-test" for ext4 tests);
rename these as appropriate ("kunit-test", "kunit-example-test"
and "ext4-inode-test" respectively).
Also define kunit_test_suite() via kunit_test_suites()
as callers in other trees may need the old definition.
Co-developed-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Theodore Ts'o <tytso@mit.edu> # for ext4 bits
Acked-by: David Gow <davidgow@google.com> # For list-test
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
We already have the of_genpd_add_subdomain() helper, but no corresponding
of_genpd_remove_subdomain(), so let's add it. Subsequent changes starts to
make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
