The TQMx86 GPIO controller only supports falling and rising edge
triggers, but not both. Fix this by implementing a software both-edge
mode that toggles the edge type after every interrupt.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Co-developed-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/515324f0491c4d44f4ef49f170354aca002d81ef.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
irq_set_type() should not implicitly unmask the IRQ.
All accesses to the interrupt configuration register are moved to a new
helper tqmx86_gpio_irq_config(). We also introduce the new rule that
accessing irq_type must happen while locked, which will become
significant for fixing EDGE_BOTH handling.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/6aa4f207f77cb58ef64ffb947e91949b0f753ccd.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The TQMx86 GPIO controller uses the same register address for input and
output data. Reading the register will always return current inputs
rather than the previously set outputs (regardless of the current
direction setting). Therefore, using a RMW pattern does not make sense
when setting output values. Instead, the previously set output register
value needs to be stored as a shadow register.
As there is no reliable way to get the current output values from the
hardware, also initialize all channels to 0, to ensure that stored and
actual output values match. This should usually not have any effect in
practise, as the TQMx86 UEFI sets all outputs to 0 during boot.
Also prepare for extension of the driver to more than 8 GPIOs by using
DECLARE_BITMAP.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/d0555933becd45fa92a85675d26e4d59343ddc01.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the TI TCA9535 variant.
The NXP PCA9535 is already supported by the driver.
TCA9535 supports lower voltage operation (down to 1.65V VCC)
compared to PCA (down to 2.3V VCC).
>From a software perspective, these models are equivalent as they
have the same register map.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240531121801.2161154-1-festevam@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The GPIO_BRCMSTB hardware IP is also included in the bcm2712
SoC so enable the driver to also be built for ARCH_BCM2835.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240530181737.1261450-1-pbrobinson@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The handling of kfifo_out() errors in read functions obscures any error.
The error condition should never occur but, while a ret is set to -EIO, it
is subsequently ignored and the read functions instead return the number
of bytes copied to that point, potentially masking the fact that any error
occurred.
Log a warning and return -EIO in the case of a kfifo_out() error to make
it clear something very odd is going on here.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-4-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The allocation of the linereq events kfifo is performed in two separate
places. Add a helper function to remove the duplication.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-3-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The initialisation of the linereq events kfifo relies on the struct being
zeroed and a subsequent call to kfifo_alloc(). The call to kfifo_alloc()
is deferred until edge detection is first enabled for the linereq. If the
kfifo is inadvertently accessed before the call to kfifo_alloc(), as was
the case in a recently discovered bug, it behaves as a FIFO of size 1 with
an element size of 0, so writes and reads to the kfifo appear successful
but copy no actual data.
As a defensive measure, initialise the kfifo with INIT_KFIFO() when the
events kfifo is constructed. This initialises the kfifo element size
and zeroes its data pointer, so any inadvertant access prior to the
kfifo_alloc() call will trigger an oops.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-2-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
rdc_gpio_config() uses pci_{read,write}_config_dword() that return
PCIBIOS_* codes. rdc_gpio_config() is used for
direction_{input,output}() in the struct gpio_chip which both require
normal errnos to be returned.
Similarly, rdc321x_gpio_probe() that is probe function returns
PCIBIOS_* codes without converting them first into normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning them to fix both issues.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132345.13956-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
amd_gpio_init() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is then returned as is but amd_gpio_init() is
a module init function that should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning it from amd_gpio_init().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132345.13956-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Do not issue "can't read the data register offset!" when gpio,syscon-dev
is not set albeit unneeded. gpio-syscon is used with rk3328 chip, but
this iomem region is documented in
Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.yaml and
does not require gpio,syscon-dev setting.
Signed-off-by: Etienne Buira <etienne.buira@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/Zktwd4Y8zu6XSGaE@Z926fQmE5jqhFMgp6
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Userspace may trigger a speculative read of an address outside the gpio
descriptor array.
Users can do that by calling gpio_ioctl() with an offset out of range.
Offset is copied from user and then used as an array index to get
the gpio descriptor without sanitization in gpio_device_get_desc().
This change ensures that the offset is sanitized by using
array_index_nospec() to mitigate any possibility of speculative
information leaks.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Link: https://lore.kernel.org/r/20240523085332.1801-1-hagarhem@amazon.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Several new features here:
- virtio-net is finally supported in vduse.
- Virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmZN570PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp2JUH/1K3fZOHymop6Y5Z3USFS7YdlF+dniedY/vg
TKyWERkXOlxq1d9DVxC0mN7tk72DweuWI0YJjLXofrEW1VuW29ecSbyFXxpeWJls
b7ErffxDAFRas5jkMCngD8TuFnbEegU0mGP5kbiHpEndBydQ2hH99Gg0x7swW+cE
xsvU5zonCCLwLGIP2DrVrn9qGOHtV6o8eZfVKDVXfvicn3lFBkUSxlwEYsO9RMup
aKxV4FT2Pb1yBicwBK4TH1oeEXqEGy1YLEn+kAHRbgoC/5L0/LaiqrkzwzwwOIPj
uPGkacf8CIbX0qZo5EzD8kvfcYL1xhU3eT9WBmpp2ZwD+4bINd4=
=nax1
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
virtio core already sets the .owner, so driver does not need to.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20240331-module-owner-virtio-v2-12-98f04bfaf46a@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Previous patch modified the standard used by acpi_gpiochip_find()
to match device nodes. Using the device node set in gc->gpiodev->d-
ev instead of gc->parent.
However, there is a situation in gpio-dwapb where the GPIO device
driver will set gc->fwnode for each port corresponding to a child
node under a GPIO device, so gc->gpiodev->dev will be assigned the
value of each child node in gpiochip_add_data().
gpio-dwapb.c:
128,31 static int dwapb_gpio_add_port(struct dwapb_gpio *gpio,
struct dwapb_port_property *pp,
unsigned int offs);
port->gc.fwnode = pp->fwnode;
693,39 static int dwapb_gpio_probe;
err = dwapb_gpio_add_port(gpio, &pdata->properties[i], i);
When other drivers request GPIO pin resources through the GPIO device
node provided by ACPI (corresponding to the parent node), the change
of the matching object to gc->gpiodev->dev in acpi_gpiochip_find()
only allows finding the value of each port (child node), resulting
in a failed request.
Reapply the condition of using gc->parent for match in acpi_gpio-
chip_find() in the code can compatible with the problem of gpio-dwapb,
and will not affect the two cases mentioned in the patch:
1. There is no setting for gc->fwnode.
2. The case that depends on using gc->fwnode for match.
Fixes: 5062e4c14b ("gpiolib: acpi: use the fwnode in acpi_gpiochip_find()")
Fixes: 067dbc1ea5 ("gpiolib: acpi: Don't use GPIO chip fwnode in acpi_gpiochip_find()")
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Following the relocation of the function call outside of
__acpi_find_gpio(), move the ACPI device NULL check to
acpi_can_fallback_to_crs().
Signed-off-by: Laura Nao <laura.nao@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: kernelci.org bot <bot@kernelci.org>
Closes: https://lore.kernel.org/all/20240426154208.81894-1-laura.nao@collabora.com/
Fixes: 49c02f6e90 ("gpiolib: acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
GPIO core:
- remove more unused legacy interfaces (after converting the last remaining
users to better alternatives)
- update kerneldocs
- improve error handling and log messages in GPIO ACPI code
- remove dead code (always true checks) from GPIOLIB
New drivers:
- add a driver for Intel Granite Rapids-D vGPIO
Driver improvements:
- use -ENOTSUPP consistently in gpio-regmap and gpio-pcie-idio-24
- provide an ID table for gpio-cros-ec to avoid a driver name fallback check
- add support for gpio-ranges for GPIO drivers supporting multiple GPIO banks
- switch to using dynamic GPIO base in gpio-brcmstb
- fix irq handling in gpio-npcm-sgpio
- switch to memory mapped IO accessors in gpio-sch
DT bindings:
- add support for gpio-ranges to gpio-brcmstb
- add support for a new model and the gpio-line-names property to gpio-mpfs
Documentation:
- replace leading tabs with spaces in code blocks
- fix typos
-----BEGIN PGP SIGNATURE-----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=mBWd
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski
"This was a quiet release cycle for the GPIO tree and so this
pull-request is relatively small.
We have one new driver, some minor improvements to the GPIO core code
and across several drivers, some DT and documentation updates but in
general nothing stands out or is controversial. All changes have spent
time in next with no reported issues (or ones that were quickly
fixed).
GPIO core:
- remove more unused legacy interfaces (after converting the last
remaining users to better alternatives)
- update kerneldocs
- improve error handling and log messages in GPIO ACPI code
- remove dead code (always true checks) from GPIOLIB
New drivers:
- add a driver for Intel Granite Rapids-D vGPIO
Driver improvements:
- use -ENOTSUPP consistently in gpio-regmap and gpio-pcie-idio-24
- provide an ID table for gpio-cros-ec to avoid a driver name
fallback check
- add support for gpio-ranges for GPIO drivers supporting multiple
GPIO banks
- switch to using dynamic GPIO base in gpio-brcmstb
- fix irq handling in gpio-npcm-sgpio
- switch to memory mapped IO accessors in gpio-sch
DT bindings:
- add support for gpio-ranges to gpio-brcmstb
- add support for a new model and the gpio-line-names property to
gpio-mpfs
Documentation:
- replace leading tabs with spaces in code blocks
- fix typos"
* tag 'gpio-updates-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (30 commits)
gpio: nuvoton: Fix sgpio irq handle error
gpiolib: Discourage to use formatting strings in line names
gpio: brcmstb: add support for gpio-ranges
gpio: of: support gpio-ranges for multiple gpiochip devices
dt-bindings: gpio: brcmstb: add gpio-ranges
gpio: Add Intel Granite Rapids-D vGPIO driver
gpio: brcmstb: Use dynamic GPIO base numbers
gpiolib: acpi: Set label for IRQ only lines
gpiolib: acpi: Add fwnode name to the GPIO interrupt label
gpiolib: Get rid of never false gpio_is_valid() calls
gpiolib: acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
gpiolib: acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
gpiolib: acpi: Simplify error handling in __acpi_find_gpio()
gpiolib: acpi: Extract __acpi_find_gpio() helper
gpio: sch: Utilise temporary variable for struct device
gpio: sch: Switch to memory mapped IO accessors
gpio: regmap: Use -ENOTSUPP consistently
gpio: pcie-idio-24: Use -ENOTSUPP consistently
Documentation: gpio: Replace leading TABs by spaces in code blocks
gpiolib: acpi: Check for errors first in acpi_find_gpio()
...
The diffstat for this release is dominated by the new Airoha driver,
mainly as a result of this being a generally quite quiet release. There
were a couple of cleanups in the core but nothing substantial, the
updates here are almost all driver specific ones.
- Support for multi-word mode in the OMAP2 McSPI driver.
- Overhaul of the PXA2xx driver, mostly API updates.
- A number of DT binding conversions.
- Support for Airoha NAND controllers, Cirrus Logic CS35L56, Mobileye
EYEQ5 and Renesas R8A779H0.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmZB2z0ACgkQJNaLcl1U
h9CCxgf/ZSy6jKbUejdq/JtdrhVCamaEVQ1X5FAk18wlumQVwFC/Bsntr1hVWDjg
Ai+G/UYWtfabyVePZKh1zCcoloSuZheHcxAMP+43un1doWcHps6leiPfb9yAysux
VxeIBfSUOfeFbN697Jz8PDTIhxHMUh0R4QYqqIyrT1RSS0alRZoDyaQpTWied0Nt
pOUWi9SVt0jm/G+X29a6Q/pFsr0oEJHxZgvriwlJAyzWr1OModFXdTfdK+qMS1Hn
huafVu4bWCEognGlnXCQSRL94Fxo1nab1PvMuWK2VXNDL7xexqQ33cp4VILZvJo1
qR9YtiRXpScAmO7f8ccGcSlz8vw5jQ==
=x3Vz
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The diffstat for this release is dominated by the new Airoha driver,
mainly as a result of this being a generally quite quiet release.
There were a couple of cleanups in the core but nothing substantial,
the updates here are almost all driver specific ones.
- Support for multi-word mode in the OMAP2 McSPI driver
- Overhaul of the PXA2xx driver, mostly API updates
- A number of DT binding conversions
- Support for Airoha NAND controllers, Cirrus Logic CS35L56, Mobileye
EYEQ5 and Renesas R8A779H0"
* tag 'spi-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: dw: Bail out early on unsupported target mode
spi: Remove unneded check for orig_nents
MAINTAINERS: repair file entry in AIROHA SPI SNFI DRIVER
spi: pxa2xx: Drop the stale entry in documentation TOC
spi: pxa2xx: Don't provide struct chip_data for others
spi: pxa2xx: Remove timeout field from struct chip_data
spi: pxa2xx: Remove DMA parameters from struct chip_data
spi: pxa2xx: Drop struct pxa2xx_spi_chip
spi: pxa2xx: Don't use "proxy" headers
spi: pxa2xx: Remove outdated documentation
spi: pxa2xx: Move contents of linux/spi/pxa2xx_spi.h to a local one
spi: pxa2xx: Provide num-cs for Sharp PDAs via device properties
spi: pxa2xx: Allow number of chip select pins to be read from property
spi: dt-bindings: ti,qspi: convert to dtschema
spi: bitbang: Add missing MODULE_DESCRIPTION()
spi: bitbang: Use NSEC_PER_*SEC rather than hard coding
spi: dw: Drop default number of CS setting
spi: dw: Convert dw_spi::num_cs to u32
spi: dw: Add a number of native CS auto-detection
spi: dw: Convert to using BITS_TO_BYTES() macro
...
If a line is requested with debounce, and that results in debouncing
in software, and the line is subsequently reconfigured to enable edge
detection then the allocation of the kfifo to contain edge events is
overlooked. This results in events being written to and read from an
uninitialised kfifo. Read events are returned to userspace.
Initialise the kfifo in the case where the software debounce is
already active.
Fixes: 65cff70464 ("gpiolib: cdev: support setting debounce")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240510065342.36191-1-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The use-after-free issue occurs as follows: when the GPIO chip device file
is being closed by invoking gpio_chrdev_release(), watched_lines is freed
by bitmap_free(), but the unregistration of lineinfo_changed_nb notifier
chain failed due to waiting write rwsem. Additionally, one of the GPIO
chip's lines is also in the release process and holds the notifier chain's
read rwsem. Consequently, a race condition leads to the use-after-free of
watched_lines.
Here is the typical stack when issue happened:
[free]
gpio_chrdev_release()
--> bitmap_free(cdev->watched_lines) <-- freed
--> blocking_notifier_chain_unregister()
--> down_write(&nh->rwsem) <-- waiting rwsem
--> __down_write_common()
--> rwsem_down_write_slowpath()
--> schedule_preempt_disabled()
--> schedule()
[use]
st54spi_gpio_dev_release()
--> gpio_free()
--> gpiod_free()
--> gpiod_free_commit()
--> gpiod_line_state_notify()
--> blocking_notifier_call_chain()
--> down_read(&nh->rwsem); <-- held rwsem
--> notifier_call_chain()
--> lineinfo_changed_notify()
--> test_bit(xxxx, cdev->watched_lines) <-- use after free
The side effect of the use-after-free issue is that a GPIO line event is
being generated for userspace where it shouldn't. However, since the chrdev
is being closed, userspace won't have the chance to read that event anyway.
To fix the issue, call the bitmap_free() function after the unregistration
of lineinfo_changed_nb notifier chain.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Link: https://lore.kernel.org/r/20240505141156.2944912-1-quic_zhonhan@quicinc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We used a per-descriptor SRCU struct in order to not impose a wait with
synchronize_srcu() for descriptor X on read-only operations of
descriptor Y. Now that we no longer call synchronize_srcu() on
descriptor label change but only when releasing descriptor resources, we
can use a single SRCU structure for all GPIO descriptors in a given chip.
Suggested-by: "Paul E. McKenney" <paulmck@kernel.org>
Acked-by: "Paul E. McKenney" <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20240507172414.28513-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Commit 1f2bcb8c8c ("gpio: protect the descriptor label with SRCU")
caused a massive drop in performance of requesting GPIO lines due to the
call to synchronize_srcu() on each label change. Rework the code to not
wait until all read-only users are done with reading the label but
instead atomically replace the label pointer and schedule its release
after all read-only critical sections are done.
To that end wrap the descriptor label in a struct that also contains the
rcu_head struct required for deferring tasks using call_srcu() and stop
using kstrdup_const() as we're required to allocate memory anyway. Just
allocate enough for the label string and rcu_head in one go.
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Closes: https://lore.kernel.org/linux-gpio/CAMRc=Mfig2oooDQYTqo23W3PXSdzhVO4p=G4+P8y1ppBOrkrJQ@mail.gmail.com/
Fixes: 1f2bcb8c8c ("gpio: protect the descriptor label with SRCU")
Suggested-by: "Paul E. McKenney" <paulmck@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Acked-by: "Paul E. McKenney" <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20240507121346.16969-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The generic_handle_domain_irq() function calls irq_resolve_mapping().
Thus delete a duplicative irq_find_mapping() call
so that a stack trace and an RCU stall will be avoided.
Fixes: c4f8457d17 ("gpio: nuvoton: Add Nuvoton NPCM sgpio driver")
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240506064244.1645922-1-JJLIU0@nuvoton.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
* New driver for vGPIO controller on Intel Granite Rapids-D
* Update ACPI GPIO library to unify the IRQ code path
* Better GPIO IRQ line labeling for ACPI
* Switched Intel SCH driver to use "mapped" I/O accessors
The following is an automated git shortlog grouped by driver:
Add Intel Granite Rapids-D vGPIO driver:
- Add Intel Granite Rapids-D vGPIO driver
crystalcove:
- Use -ENOTSUPP consistently
gpiolib:
- acpi: Set label for IRQ only lines
- acpi: Add fwnode name to the GPIO interrupt label
- acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
- acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
- acpi: Simplify error handling in __acpi_find_gpio()
- acpi: Extract __acpi_find_gpio() helper
- acpi: Check for errors first in acpi_find_gpio()
- acpi: Remove never true check in acpi_get_gpiod_by_index()
sch:
- Utilise temporary variable for struct device
- Switch to memory mapped IO accessors
wcove:
- Use -ENOTSUPP consistently
-----BEGIN PGP SIGNATURE-----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=33sC
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.10-1
* New driver for vGPIO controller on Intel Granite Rapids-D
* Update ACPI GPIO library to unify the IRQ code path
* Better GPIO IRQ line labeling for ACPI
* Switched Intel SCH driver to use "mapped" I/O accessors
The following is an automated git shortlog grouped by driver:
Add Intel Granite Rapids-D vGPIO driver:
- Add Intel Granite Rapids-D vGPIO driver
crystalcove:
- Use -ENOTSUPP consistently
gpiolib:
- acpi: Set label for IRQ only lines
- acpi: Add fwnode name to the GPIO interrupt label
- acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
- acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
- acpi: Simplify error handling in __acpi_find_gpio()
- acpi: Extract __acpi_find_gpio() helper
- acpi: Check for errors first in acpi_find_gpio()
- acpi: Remove never true check in acpi_get_gpiod_by_index()
sch:
- Utilise temporary variable for struct device
- Switch to memory mapped IO accessors
wcove:
- Use -ENOTSUPP consistently
A pin controller device mapped with the gpio-ranges property
will need implementations of the .request and .free members of
the gpiochip.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Tested-by: Phil Elwell <phil@raspberrypi.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424185039.1707812-4-opendmb@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Some drivers (e.g. gpio-mt7621 and gpio-brcmstb) have multiple
gpiochip banks within a single device. Unfortunately, the
gpio-ranges property of the device node was being applied to
every gpiochip of the device with device relative GPIO offset
values rather than gpiochip relative GPIO offset values.
This commit makes use of the gpio_chip offset value which can be
non-zero for such devices to split the device node gpio-ranges
property into GPIO offset ranges that can be applied to each
of the relevant gpiochips of the device.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424185039.1707812-3-opendmb@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
* Make data pointer dereference robust in Intel Tangier driver
The following is an automated git shortlog grouped by driver:
tangier:
- Use correct type for the IRQ chip data
-----BEGIN PGP SIGNATURE-----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=688G
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current
intel-gpio for v6.9-2
* Make data pointer dereference robust in Intel Tangier driver
The following is an automated git shortlog grouped by driver:
tangier:
- Use correct type for the IRQ chip data
This driver provides a basic GPIO driver for the Intel Granite Rapids-D
virtual GPIOs. On SoCs with limited physical pins on the package, the
physical pins controlled by this driver would be exposed on an external
device such as a BMC or CPLD. The virtual GPIO registers are an
interface to firmware, which communicates with the external device that
implements the GPIO hardware functionality.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The controller has several register bits describing access control
information for a given GPIO pin. When SCR_SEC_[R|W]EN is unset, it
means we have full read/write access to all the registers for given GPIO
pin. When SCR_SEC[R|W]EN is set, it means we need to further check the
accompanying SCR_SEC_G1[R|W] bit to determine read/write access to all
the registers for given GPIO pin.
This check was previously declaring that a GPIO pin was accessible
only if either of the following conditions were met:
- SCR_SEC_REN + SCR_SEC_WEN both set
or
- SCR_SEC_REN + SCR_SEC_WEN both set and
SCR_SEC_G1R + SCR_SEC_G1W both set
Update the check to properly handle cases where only one of
SCR_SEC_REN or SCR_SEC_WEN is set.
Fixes: b2b56a1632 ("gpio: tegra186: Check GPIO pin permission before access.")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240424095514.24397-1-pshete@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Forcing a gpiochip to have a fixed base number now leads to a warning
message. Remove the need to do so by using the offset value of the
gpiochip.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240423184605.2094376-1-opendmb@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When line locked as IRQ it has no label assigned. Assign
the meaningful value to it.
Ex. (for the PCA9355 and MAX3111e chips connected to the system):
=== Before ===
PCA953x: interrupt
MAX3111e: interrupt
=== After ===
PCA953x: NIO1 GpioInt(0)
MAX3111e: URT0 GpioInt(0)
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's ambiguous to have a device-related index in the GPIO interrupt
label as most of the devices will have it the same or very similar.
Extend label with fwnode name for better granularity. It significantly
reduces the scope of searching among devices.
Ex. (for the PCA9355 and MAX3111e chips connected to the system):
=== Before ===
PCA953x: GpioInt() 0
MAX3111e: GpioInt() 0
=== After ===
PCA953x: NIO1 GpioInt(0)
MAX3111e: URT0 GpioInt(0)
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In the cases when gpio_is_valid() is called with unsigned parameter
the result is always true in the GPIO library code, hence the check
for false won't ever be true. Get rid of such calls.
While at it, move GPIO device base to be unsigned to clearly show
it won't ever be negative. This requires a new definition for the
maximum GPIO number in the system.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
SPI devices can specify a cs-gpios property to enumerate their
chip selects. Under device tree, a zero entry in this property can
be used to specify that a particular chip select is using the SPI
controllers native chip select, for example:
cs-gpios = <&gpio1 0 0>, <0>;
Here, the second chip select is native. However, when using swnodes
there is currently no way to specify a native chip select. The
proposal here is to register a swnode_gpio_undefined software node,
that can be specified to allow the indication of a native chip
select. For example:
static const struct software_node_ref_args device_cs_refs[] = {
{
.node = &device_gpiochip_swnode,
.nargs = 2,
.args = { 0, GPIO_ACTIVE_LOW },
},
{
.node = &swnode_gpio_undefined,
.nargs = 0,
},
};
Register the swnode as the gpiolib is initialised and check in
swnode_get_gpio_device() if the returned node matches
swnode_gpio_undefined and return -ENOENT, which matches the
behaviour of the device tree system when it encounters a 0 phandle.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pass the con_id instead of property so that callers won't repeat
the GPIO suffixes to try.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
New coming user may need to check for _CRS fallback slightly differently.
Move the current check out of the helper function to allow that user to
use it.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Now that we don't perform anything on the GPIO descriptor,
we may simplify the error path in newly introduced helper.
Do it so.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We want to reuse it later on in the code. In particular, it helps
to clean up the users of acpi_dev_gpio_irq_wake_get_by().
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We have a temporary variable to keep a pointer to struct device.
Utilise it where it makes sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
IRQ chip data contains a pointer to the GPIO chip. Luckily we have
the pointers the same, but strictly speaking it's not guaranteed.
Even though, still better to fix this.
Fixes: ccf6fd6dcc ("gpio: merrifield: Introduce GPIO driver to support Merrifield")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The GPIO library expects the drivers to return -ENOTSUPP in some cases
and not using analogue POSIX code. Make the driver to follow this.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The GPIO library expects the drivers to return -ENOTSUPP in some cases
and not using analogue POSIX code. Make the driver to follow this.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: William Breathitt Gray <wbg@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
It's better to parse the code when the usual pattern is being used,
i.e. checking for error condition first.
There is no functional or code generation change (tested in LLVM).
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The acpi_get_gpiod_by_index() never is called with adev being NULL.
Remove the redundant check.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* Fix returned code in the error path in Intel PMIC GPIO drivers
The following is an automated git shortlog grouped by driver:
crystalcove:
- Use -ENOTSUPP consistently
wcove:
- Use -ENOTSUPP consistently
-----BEGIN PGP SIGNATURE-----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=nT1m
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current
intel-gpio for v6.9-1
* Fix returned code in the error path in Intel PMIC GPIO drivers
The following is an automated git shortlog grouped by driver:
crystalcove:
- Use -ENOTSUPP consistently
wcove:
- Use -ENOTSUPP consistently
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When adding sanitization of the label, the path through
edge_detector_setup() that leads to debounce_setup() was overlooked.
A request taking this path does not allocate a new label and the
request label is freed twice when the request is released, resulting
in memory corruption.
Add label sanitization to debounce_setup().
Cc: stable@vger.kernel.org
Fixes: b34490879b ("gpio: cdev: sanitize the label before requesting the interrupt")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
[Bartosz: rebased on top of the fix for empty GPIO labels]
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We need to take into account that a line's consumer label may be NULL
and not try to kstrdup() it in that case but rather pass the NULL
pointer up the stack to the interrupt request function.
To that end: let make_irq_label() return NULL as a valid return value
and use ERR_PTR() instead to signal an allocation failure to callers.
Cc: stable@vger.kernel.org
Fixes: b34490879b ("gpio: cdev: sanitize the label before requesting the interrupt")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/lkml/20240402093534.212283-1-naresh.kamboju@linaro.org/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
We are going to remove legacy API from kernel, don't mention
it in the code that does not use it already for a while.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
No more users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When a gpiochip gets added by loading a module, then another driver may
be waiting for that gpiochip to load on the deferred-probe list.
If the deferred-probe for the consumer of gpiochip then triggers between
the gpiodev_add_to_list_unlocked() calls which makes gpio_device_find()
see the chip and the gpiochip_setup_dev() later then gpio_device_find()
does a kobject_get() on an uninitialized kobject since the kobject is
initialized by gpiochip_setup_dev() calling device_initialize():
arizona spi-10WM5102:00: cannot find GPIO chip arizona, deferring
arizona spi-10WM5102:00: cannot find GPIO chip arizona, deferring
------------[ cut here ]------------
kobject: 'gpiochip5' (00000000241466f2): is not initialized, yet kobject_get() is being called.
WARNING: CPU: 3 PID: 42 at lib/kobject.c:640 kobject_get+0x43/0x70
Call Trace:
kobject_get
gpio_device_find
gpiod_find_and_request
gpiod_get
snd_byt_wm5102_mc_probe
Not only is the device not initialized yet, but when the gpio-device is
added to the list things like the irqchip also have not been initialized
yet.
So gpio_device_find() should really ignore the gpio-device until
gpiochip_add_data_with_key() is fully done. Add a device_is_registered()
check to gpio_device_find() to ignore gpio-devices on the list which are
not yet fully initialized.
Fixes: aab5c6f200 ("gpio: set device type for GPIO chips")
Suggested-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
[Bartosz: fix a typo in commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Instead of using fallback driver name match, provide ID table[1] for the
primary match. Also allow automatic module loading by adding
MODULE_DEVICE_TABLE().
[1]: https://elixir.bootlin.com/linux/v6.8/source/drivers/base/platform.c#L1353
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When gpio-ranges property was missed to be added in the gpio node,
using dev_err() to show an error message will helping to locate issues
easier.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When consolidating GPIO lookups in ACPI code, the debug messaging
had been reworked that the user may see
[ 13.401147] (NULL device *): using ACPI '\_SB.LEDS.led-0' for '(null)' GPIO lookup
[ 13.401378] gpio gpiochip0: Persistence not supported for GPIO 40
[ 13.401402] gpio-40 (?): no flags found for (null)
instead of
[ 14.182962] gpio gpiochip0: Persistence not supported for GPIO 40
[ 14.182994] gpio-40 (?): no flags found for gpios
The '(null)' parts are less informative and likely scare the users.
Replace them by '(default)' which can point out to the default connection
IDs, such as 'gpios'.
While at it, amend other places where con_id is used in the messages.
Reported-by: Ferry Toth <ftoth@exalondelft.nl>
Fixes: 8eb1f71e7a ("gpiolib: consolidate GPIO lookups")
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When an interrupt is requested, a procfs directory is created under
"/proc/irq/<irqnum>/<label>" where <label> is the string passed to one of
the request_irq() variants.
What follows is that the string must not contain the "/" character or
the procfs mkdir operation will fail. We don't have such constraints for
GPIO consumer labels which are used verbatim as interrupt labels for
GPIO irqs. We must therefore sanitize the consumer string before
requesting the interrupt.
Let's replace all "/" with ":".
Cc: stable@vger.kernel.org
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Closes: https://lore.kernel.org/linux-gpio/39fe95cb-aa83-4b8b-8cab-63947a726754@gmx.net/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander.
I found this living out-of-tree in OpenWrt as an upstream
attempt had stalled on the finishing line, so I picked it
up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of
tree for the ST STA chips, and now the IP was re-used in a
MIPS automotive SoC called MobilEyeq5, so it has been split
in pin control and GPIO drivers so the latter can be reused
by MobilEyeq5. (Along with a long list of cleanups.)
- A lot of overall cleanup and tidying up.
-----BEGIN PGP SIGNATURE-----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=Pt9Y
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander. I found this
living out-of-tree in OpenWrt as an upstream attempt had stalled on
the finishing line, so I picked it up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of tree
for the ST STA chips, and now the IP was re-used in a MIPS
automotive SoC called MobilEyeq5, so it has been split in pin
control and GPIO drivers so the latter can be reused by MobilEyeq5.
(Along with a long list of cleanups)
- A lot of overall cleanup and tidying up"
* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
dt-bindings: pinctrl: qcom: update compatible name for match with driver
pinctrl: aw9523: Make the driver tristate
pinctrl: nomadik: fix dereference of error pointer
gpio: nomadik: Back out some managed resources
pinctrl: aw9523: Add proper terminator
pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
gpio: nomadik: Finish conversion to use firmware node APIs
gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
pinctrl: da9062: Add OF table
dt-bindings: pinctrl: at91: add sam9x7
pinctrl: ocelot: remove redundant assignment to variable ret
gpio: nomadik: grab optional reset control and deassert it at probe
gpio: nomadik: support mobileye,eyeq5-gpio
gpio: nomadik: handle variadic GPIO count
gpio: nomadik: support shared GPIO IRQs
...
Serialization rework:
- use SRCU to serialize access to the global GPIO device list, to GPIO device
structs themselves and to GPIO descriptors
- make the GPIO subsystem resilient to the GPIO providers being unbound while
the API calls are in progress
- don't dereference the SRCU-protected chip pointer if the information we need
can be obtained from the GPIO device structure
- move some of the information contained in struct gpio_chip to struct
gpio_device to further reduce the need to dereference the former
- pass the GPIO device struct instead of the GPIO chip to sysfs callback to,
again, reduce the need for accessing the latter
- get GPIO descriptors from the GPIO device, not from the chip for the same
reason
- allow for mostly lockless operation of the GPIO driver API: assure
consistency with SRCU and atomic operations
- remove the global GPIO spinlock
- remove the character device RW semaphore
Core GPIOLIB:
- constify pointers in GPIO API where applicable
- unify the GPIO counting APIs for ACPI and OF
- provide a macro for iterating over all GPIOs, not only the ones that are
requested
- remove leftover typedefs
- pass the consumer device to GPIO core in devm_fwnode_gpiod_get_index() for
improved logging
- constify the GPIO bus type
- don't warn about removing GPIO chips with descriptors still held by users as
we can now handle this situation gracefully
- remove unused logging helpers
- unexport functions that are only used internally in the GPIO subsystem
- set the device type (assign the relevant struct device_type) for GPIO devices
New drivers:
- add the ChromeOS EC GPIO driver
Driver improvements:
- allow building gpio-vf610 with COMPILE_TEST as well as disabling it in
menuconfig (before it was always built for i.MX cofigs)
- count the number of EICs using the device properties instead of hard-coding
it in gpio-eic-sprd
- improve the device naming, extend the debugfs output and add lockdep asserts
to gpio-sim
DT bindings:
- document the 'label' property for gpio-pca9570
- convert aspeed,ast2400-gpio bindings to DT schema
- disallow unevaluated properties for gpio-mvebu
- document a new model in renesas,rcar-gpio
Documentation:
- improve the character device kerneldocs in user-space headers
- add proper documentation for the character device uAPI (both v1 and v2)
- move the sysfs and gpio-mockup docs into the "obsolete" section
- improve naming consistency for GPIO terms
- clarify the line values description for sysfs
- minor docs improvements
- improve the driver API contract for setting GPIO direction
- mark unsafe APIs as deprecated in kerneldocs and suggest replacements
Other:
- remove an obsolete test from selftests
-----BEGIN PGP SIGNATURE-----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=LX+L
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"The biggest feature is the locking overhaul. Up until now the
synchronization in the GPIO subsystem was broken. There was a single
spinlock "protecting" multiple data structures but doing it wrong (as
evidenced by several places where it would be released when a sleeping
function was called and then reacquired without checking the protected
state).
We tried to use an RW semaphore before but the main issue with GPIO is
that we have drivers implementing the interfaces in both sleeping and
non-sleeping ways as well as user-facing interfaces that can be called
both from process as well as atomic contexts. Both ends converge in
the same code paths that can use neither spinlocks nor mutexes. The
only reasonable way out is to use SRCU and go mostly lockless. To that
end: we add several SRCU structs in relevant places and use them to
assure consistency between API calls together with atomic reads and
writes of GPIO descriptor flags where it makes sense.
This code has spent several weeks in next and has received several
fixes in the first week or two after which it stabilized nicely. The
GPIO subsystem is now resilient to providers being suddenly unbound.
We managed to also remove the existing character device RW semaphore
and the obsolete global spinlock.
Other than the locking rework we have one new driver (for Chromebook
EC), much appreciated documentation improvements from Kent and the
regular driver improvements, DT-bindings updates and GPIOLIB core
tweaks.
Serialization rework:
- use SRCU to serialize access to the global GPIO device list, to
GPIO device structs themselves and to GPIO descriptors
- make the GPIO subsystem resilient to the GPIO providers being
unbound while the API calls are in progress
- don't dereference the SRCU-protected chip pointer if the
information we need can be obtained from the GPIO device structure
- move some of the information contained in struct gpio_chip to
struct gpio_device to further reduce the need to dereference the
former
- pass the GPIO device struct instead of the GPIO chip to sysfs
callback to, again, reduce the need for accessing the latter
- get GPIO descriptors from the GPIO device, not from the chip for
the same reason
- allow for mostly lockless operation of the GPIO driver API: assure
consistency with SRCU and atomic operations
- remove the global GPIO spinlock
- remove the character device RW semaphore
Core GPIOLIB:
- constify pointers in GPIO API where applicable
- unify the GPIO counting APIs for ACPI and OF
- provide a macro for iterating over all GPIOs, not only the ones
that are requested
- remove leftover typedefs
- pass the consumer device to GPIO core in
devm_fwnode_gpiod_get_index() for improved logging
- constify the GPIO bus type
- don't warn about removing GPIO chips with descriptors still held by
users as we can now handle this situation gracefully
- remove unused logging helpers
- unexport functions that are only used internally in the GPIO
subsystem
- set the device type (assign the relevant struct device_type) for
GPIO devices
New drivers:
- add the ChromeOS EC GPIO driver
Driver improvements:
- allow building gpio-vf610 with COMPILE_TEST as well as disabling it
in menuconfig (before it was always built for i.MX cofigs)
- count the number of EICs using the device properties instead of
hard-coding it in gpio-eic-sprd
- improve the device naming, extend the debugfs output and add
lockdep asserts to gpio-sim
DT bindings:
- document the 'label' property for gpio-pca9570
- convert aspeed,ast2400-gpio bindings to DT schema
- disallow unevaluated properties for gpio-mvebu
- document a new model in renesas,rcar-gpio
Documentation:
- improve the character device kerneldocs in user-space headers
- add proper documentation for the character device uAPI (both v1 and v2)
- move the sysfs and gpio-mockup docs into the "obsolete" section
- improve naming consistency for GPIO terms
- clarify the line values description for sysfs
- minor docs improvements
- improve the driver API contract for setting GPIO direction
- mark unsafe APIs as deprecated in kerneldocs and suggest
replacements
Other:
- remove an obsolete test from selftests"
* tag 'gpio-updates-for-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (79 commits)
gpio: sysfs: repair export returning -EPERM on 1st attempt
selftest: gpio: remove obsolete gpio-mockup test
gpiolib: Deduplicate cleanup for-loop in gpiochip_add_data_with_key()
dt-bindings: gpio: aspeed,ast2400-gpio: Convert to DT schema
gpio: acpi: Make acpi_gpio_count() take firmware node as a parameter
gpio: of: Make of_gpio_get_count() take firmware node as a parameter
gpiolib: Pass consumer device through to core in devm_fwnode_gpiod_get_index()
gpio: sim: use for_each_hwgpio()
gpio: provide for_each_hwgpio()
gpio: don't warn about removing GPIO chips with active users anymore
gpio: sim: delimit the fwnode name with a ":" when generating labels
gpio: sim: add lockdep asserts
gpio: Add ChromeOS EC GPIO driver
gpio: constify of_phandle_args in of_find_gpio_device_by_xlate()
gpio: fix memory leak in gpiod_request_commit()
gpio: constify opaque pointer "data" in gpio_device_find()
gpio: cdev: fix a NULL-pointer dereference with DEBUG enabled
gpio: uapi: clarify default_values being logical
gpio: sysfs: fix inverted pointer logic
gpio: don't let lockdep complain about inherently dangerous RCU usage
...
This contains the usual amount of driver and device tree changes.
Additionally there is a big rework of how pwm lowlevel drivers are
registered to prepare adding character device support.
Thanks to Dharma Balasubiramani, Dong Aisheng, Duje Mihanović, Jerome
Brunet, Raag Jadav and Rafał Miłecki for their contributions. And sorry
for those who still need some patience because I didn't manage to empty
my review queue.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEP4GsaTp6HlmJrf7Tj4D7WH0S/k4FAmXuyf4ACgkQj4D7WH0S
/k4Yugf+P7gMPuCQJqWLvOyuHjKt4tI3aVsr+jbSiAfbPWaXAQKZunnZ9K17bOI2
JQkDuAi76teNRiVtNEx1ZEdfKe9KgY/Npq8BTmvXxvBktCand8sfhyyRaXYo9FWI
B5qKdp1WIg7ZDMoGQtLRayly4FAsbB0L50SjWmkVIXC2xXp6t6KxxgnOgTM58Oo9
0yYYetF3EOmDQ4J234/muaLbM+1rjajKdw+SgS2mry2WV60SOqo+PQfuK42XjWip
cLDkEgYogwx1MAbFgobtquA7Hvkdb2WyCirTDNZiGIBtmM89kH4Oa8e4IDR6FRqn
w35hJv7sxVjiqBrSMD/lWpJeQ8gPYg==
=6Ixv
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm updates from Uwe Kleine-König:
"This contains the usual amount of driver and device tree changes.
Additionally there is a big rework of how pwm lowlevel drivers are
registered to prepare adding character device support.
Thanks to Dharma Balasubiramani, Dong Aisheng, Duje Mihanović, Jerome
Brunet, Raag Jadav and Rafał Miłecki for their contributions. And
sorry for those who still need some patience because I didn't manage
to empty my review queue"
* tag 'pwm/for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux: (185 commits)
pwm: imx-tpm: fix probe crash due to access registers without clock
pwm: meson: generalize 4 inputs clock on meson8 pwm type
dt-bindings: pwm: amlogic: Add a new binding for meson8 pwm types
dt-bindings: pwm: amlogic: fix s4 bindings
pwm: dwc: simplify error handling
pwm: dwc: Add 16 channel support for Intel Elkhart Lake
pwm: dwc: drop redundant error check
staging: greybus: pwm: Make use of devm_pwmchip_alloc() function
staging: greybus: pwm: Rework how the number of PWM lines is determined
staging: greybus: pwm: Drop unused gb_connection_set_data()
staging: greybus: pwm: Rely on pwm framework to pass a valid hwpwm
staging: greybus: pwm: Make use of pwmchip_parent() accessor
staging: greybus: pwm: Change prototype of helpers to prepare further changes
leds: qcom-lpg: Make use of devm_pwmchip_alloc() function
drm/bridge: ti-sn65dsi86: Make use of devm_pwmchip_alloc() function
drm/bridge: ti-sn65dsi86: Make use of pwmchip_parent() accessor
gpio: mvebu: Make use of devm_pwmchip_alloc() function
pwm: xilinx: Make use of devm_pwmchip_alloc() function
pwm: xilinx: Prepare removing pwm_chip from driver data
pwm: vt8500: Make use of devm_pwmchip_alloc() function
...
When `CONFIG_DEBUG_FS` is disabled, nmk_gpio_dbg_show_one() is an
empty dummy function; this however triggers a `-Wmissing-prototypes`
warning and later a linker error because the function is also used by
drivers/pinctrl/nomadik/pinctrl-nomadik.c, therefore it needs to be
non-static.
To allow both sources to access this dummy function, this patch moves
it to the header, adding the `#ifdef CONFIG_DEBUG_FS` there as well.
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Link: https://lore.kernel.org/r/20240311133223.3429428-1-max.kellermann@ionos.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using BUG_ON() is discouraged and also the check wasn't done early
enough to prevent an out of bounds access. Check earlier and return
an error instead of calling BUG().
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ae643df0-3a3e-4270-8dbf-be390ee4b478@moroto.mountain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It would make sense to return -EPERM if the bit was already set (already
used), not if it was cleared. Before this fix pins can only be exported on
the 2nd attempt:
$ echo 522 > /sys/class/gpio/export
sh: write error: Operation not permitted
$ echo 522 > /sys/class/gpio/export
Fixes: 35b545332b ("gpio: remove gpio_lock")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Several commits introduce managed resources (devm_*) into the
nmk_gpio_populate_chip() function.
This isn't always working because when called from the Nomadik pin
control driver we just want to populate some states for the device as
the same states are used by the pin control driver.
Some managed resources such as devm_kzalloc() etc will work, as the
passed in platform device will be used for lifecycle management,
but in some cases where we used the looked-up platform device
for the GPIO block, this will cause problems for the combined
pin control and GPIO driver, because it adds managed resources
to the GPIO device before it is probed, which is something that
the device core will not accept, and all of the GPIO blocks will
refuse to probe:
platform 8012e000.gpio: Resources present before probing
platform 8012e080.gpio: Resources present before probing
(...)
Fix this by not tying any managed resources to the looked-up
gpio_pdev/gpio_dev device, let's just live with the fact that
these need imperative resource management for now.
Drop in some notes and use a local *dev variable to clarify the
code.
Cc: Théo Lebrun <theo.lebrun@bootlin.com>
Fixes: 12410e9590 ("gpio: nomadik: use devm_platform_ioremap_resource() helper")
Link: https://lore.kernel.org/r/20240305-fix-nomadik-gpio-v2-1-e5d1fbdc3f5c@linaro.org
[Fixed some last minut print formatting]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to repeat for-loop twice in the error path in
gpiochip_add_data_with_key(). Deduplicate it. While at it,
rename loop variable to be more specific and avoid ambguity.
It also properly unwinds the SRCU, i.e. in reversed order of allocating.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Previously driver got a few updates in order to replace OF APIs by
respective firmware node, however it was not finished to the logical
end, e.g., some APIs that has been used are still require OF node
to be passed. Finish that job by converting leftovers to use firmware
node APIs.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240302173401.217830-1-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61 ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Make acpi_gpio_count() take firmware node as a parameter in order
to be aligned with other functions and decouple from unused device
pointer. The latter helps to create a common fwnode_gpio_count()
in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Make of_gpio_get_count() take firmware node as a parameter in order
to be aligned with other functions and decouple from unused device
pointer. The latter helps to create a common fwnode_gpio_count()
in the future.
While at it, rename to be of_gpio_count() to be aligned with the others.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
After shuffling the code, error path wasn't updated correctly.
Fix it here.
Fixes: 2f4133bb5f ("gpiolib: No need to call gpiochip_remove_pin_ranges() twice")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0f (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Fetch a reference to the optional shared reset control and deassert it
if it exists.
Optional because not all platforms that use this driver have a reset
attached to the reset block. Shared because some platforms that use the
reset (at least Mobileye EyeQ5) share the reset across banks.
Do not keep a reference to the reset control as it is not needed
afterwards; the driver does not handle suspend, does not use runtime
PM, does not register a remove callback and does not support unbinding
from sysfs (made explicit with suppress_bind_attrs).
The operation is done in nmk_gpio_populate_chip(). This function is
called by either gpio-nomadik or pinctrl-nomadik, whoever comes first.
This is here for historic reasons and could probably be removed now; it
seems gpio-ranges enforces the ordering to be pinctrl-first. It is not
the topic of the present patch however.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-25-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We create a custom compatible for the STA2X11 IP block as integrated
into the Mobileye EyeQ5 platform. Its wake and alternate functions have
been disabled, we want to avoid touching those registers.
We both do: (1) early return in functions that do not support the
platform, but with warnings, and (2) avoid calling those functions in
the first place.
We ensure that pinctrl-nomadik is not used with this STA2X11 variant.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-24-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Read the "ngpios" property to determine the number of GPIOs for a bank.
If not available, fallback to NMK_GPIO_PER_CHIP ie 32 ie the current
behavior.
The IP block always supports 32 GPIOs, but platforms can expose a lesser
amount. The Mobileye EyeQ5 is in this case; one bank is 29 GPIOs and
the other is 23.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-23-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support a single IRQs used by multiple GPIO banks. Change the IRQ
handler type from a chained handler (as used by gpiolib
for ->parent_handler) to a threaded IRQ.
Use the generic_handle_domain_irq_safe() helper. The non-safe version
must be called in a no-IRQ context.
The Mobileye EyeQ5 platform uses this GPIO controller and share an IRQ
for its two banks.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-22-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This GPIO driver is historically related to the Nomadik platform. It
however can be used by others as it implements the ST STA2X11 IP block.
Pick a less ambiguous name for it.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-21-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not all platforms using this platform driver expose a clock for this
GPIO controller. Turn devm_clk_get() into devm_clk_get_optional() to
avoid failing when no clocks are provided.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-20-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move away from statically allocated GPIO IDs. Switch to dynamic ID
allocation. Static IDs are deprecated because they cause issues when
multiple GPIO controllers are to be found on the same platform.
Add a bit of complexity to do pin number -> GPIO chip + offset.
Previously, bank number and offsets were retrieved using division and
remainder (bank size being constant 32). Now, to get the pin number
matching a bank base, we must know the sum of ngpios of previous banks.
This is done in find_nmk_gpio_from_pin() which also exposes the offset
inside the bank.
Also remove the assumption that bank sizes are constant. Instead of
using NMK_GPIO_PER_CHIP as bank size, use nmk_gpio_chips[i]->ngpio.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-19-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace call to clk_get() by call to devm_clk_get(). Allow automatic
cleanup of the clock in case of probe error.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-18-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace calls to platform_get_resource() then devm_ioremap_resource() by
a single call to devm_platform_ioremap_resource().
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-17-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Avoid OF APIs in the GPIO subsystem. Here, replace
of_find_device_by_node() call by bus_find_device_by_of_node().
The new helper returns a struct device pointer. Store it in a new local
variable and use it down the road.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-15-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Previously, drivers/pinctrl/nomadik/pinctrl-nomadik.c registered two
platform drivers: pinctrl & GPIO. Move the GPIO aspect to the
drivers/gpio/ folder, as would be expected.
Both drivers are intertwined for a reason; pinctrl requires access to
GPIO registers for pinmuxing, pull-disable, disabling interrupts while
setting the muxing and wakeup control. Information sharing is done
through a shared array containing GPIO chips and a few helper
functions. That shared array is not touched from gpio-nomadik when
CONFIG_PINCTRL_NOMADIK is not defined.
Make no change to the code that moved into gpio-nomadik; there should be
no behavior change following. A few functions are shared and header
comments are added. Checkpatch warnings are addressed. NUM_BANKS is
renamed to NMK_MAX_BANKS.
It is supported to compile gpio-nomadik without pinctrl-nomadik. The
opposite is not true.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-6-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devm API takes a consumer device as an argument to setup the devm
action, but throws it away when calling further into gpiolib. This leads
to odd debug messages like this:
(NULL device *): using DT '/gpio-keys/switch-pen-insert' for '(null)' GPIO lookup
Let's pass the consumer device down, by directly calling what
fwnode_gpiod_get_index() calls but pass the device used for devm. This
changes the message to look like this instead:
gpio-keys gpio-keys: using DT '/gpio-keys/switch-pen-insert' for '(null)' GPIO lookup
Note that callers of fwnode_gpiod_get_index() will still see the NULL
device pointer debug message, but there's not much we can do about that
because the API doesn't take a struct device.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 8eb1f71e7a ("gpiolib: consolidate GPIO lookups")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Display debugfs information about all simulated GPIOs, not only the
requested ones.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
With SRCU we can now correctly handle the situation when a GPIO provider
is removed while having users still holding references to GPIO
descriptors. Remove all warnings emitted in this situation.
Suggested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Typically, whenever a human-readable name is created for objects using
a software node, its name is delimited with ":" as dashes are often used
in other parts of the name. Make gpio-sim use the same pattern. This
results in better looking default names:
gpio-sim.0:node0
gpio-sim.0:node1
gpio-sim.1:node0
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
We have three functions in gpio-sim that are called with the device lock
already held. We use the "_unlocked" suffix in their names to indicate
that. This has proven to be confusing though as the naming convention in
the kernel varies between using "_locked" or "_unlocked" for this
purpose. Naming convention also doesn't enforce anything. Let's remove
the suffix and add lockdep annotation at the top of these functions.
This makes it clear the function requires a lock to be held (and which
one specifically!) as well as results in a warning if it's not the case.
The only place where the information is lost is the place where the
function is called but the caller doesn't care about that information
anyway.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The ChromeOS embedded controller (EC) supports setting the state of
GPIOs when the system is unlocked, and getting the state of GPIOs in all
cases. The GPIOs are on the EC itself, so the EC acts similar to a GPIO
expander. Add a driver to get and set the GPIOs on the EC through the
host command interface.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Similar to gpiochip_generic_request() and gpiochip_generic_free() the
gpiochip_generic_config() function needs to handle the case where there
are no pinctrl pins mapped to the GPIOs, usually through the gpio-ranges
device tree property.
Commit f34fd6ee1b ("gpio: dwapb: Use generic request, free and
set_config") set the .set_config callback to gpiochip_generic_config()
in the dwapb GPIO driver so the GPIO API can set pinctrl configuration
for the corresponding pins. Most boards using the dwapb driver do not
set the gpio-ranges device tree property though, and in this case
gpiochip_generic_config() would return -EPROPE_DEFER rather than the
previous -ENOTSUPP return value. This in turn makes
gpio_set_config_with_argument_optional() fail and propagate the error to
any driver requesting GPIOs.
Fixes: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Reported-by: Jisheng Zhang <jszhang@kernel.org>
Closes: https://lore.kernel.org/linux-gpio/ZdC_g3U4l0CJIWzh@xhacker/
Tested-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Pointer to the struct of_phandle_args can be made const after
gpio_device_find() arguments got constified. This should be part of
commit 4a92857d6e ("gpio: constify opaque pointer "data" in
gpio_device_find()").
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The opaque pointer "data" in each match function used by
gpio_device_find() is a pointer to const, thus the same argument passed
to gpio_device_find() can adjusted similarly.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We are actually passing the gc pointer to chip_dbg() so we have to
srcu_dereference() it.
Fixes: 8574b5b476 ("gpio: cdev: use correct pointer accessors with SRCU")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/lkml/179caa10-5f86-4707-8bb0-fe1b316326d6@samsung.com/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
There are two legacy, deprecated functions - gpiod_to_chip() and
gpio_device_get_chip() - that still have users in tree. They return the
address of the SRCU-protected chip outside of the read-only critical
sections. They are inherently dangerous and the users should convert to
safer alternatives. Let's explicitly silence lockdep warnings by using
rcu_dereference_check(ptr, 1). While at it: reuse
gpio_device_get_chip() in gpiod_to_chip().
Fixes: d83cee3d2b ("gpio: protect the pointer to gpio_chip in gpio_device with SRCU")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202402122234.d85cca9b-lkp@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Lockdep with CONFIG_PROVE_RCU enabled reports false positives about
suspicious rcu_dereference() usage. Let's silence it by using
srcu_dereference() which is the correct helper with SRCU.
Fixes: d83cee3d2b ("gpio: protect the pointer to gpio_chip in gpio_device with SRCU")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202402122234.d85cca9b-lkp@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
We never dereference the chip pointer in character device code so we can
use the lighter rcu_access_pointer() helper. This also makes lockep
happier as it no longer complains about suspicious rcu_dereference()
usage.
Fixes: d83cee3d2b ("gpio: protect the pointer to gpio_chip in gpio_device with SRCU")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202402122234.d85cca9b-lkp@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
gpiod_hog() may be called without the gpio_device SRCU read lock taken
so we need to do it here as well. It's alright if someone else is
already holding the lock as SRCU read critical sections can be nested.
Fixes: d83cee3d2b ("gpio: protect the pointer to gpio_chip in gpio_device with SRCU")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202402122234.d85cca9b-lkp@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
In certain situations we may end up taking the GPIO descriptor SRCU read
lock in of_gpiochip_add() before the SRCU struct is initialized. Move
the initialization before the call to of_gpiochip_add().
Fixes: be711caa87 ("gpio: add SRCU infrastructure to struct gpio_desc")
Fixes: 1f2bcb8c8c ("gpio: protect the descriptor label with SRCU")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202402122228.e607a080-lkp@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We still have some functions that return the address of the GPIO chip
associated with the GPIO device. This is dangerous and the users should
find a better solution. Let's add appropriate comments to the kernel
docs.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
With all accesses to gdev->chip being protected with SRCU, we can now
remove the RW-semaphore specific to the character device which
fulfilled the same role up to this point.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Ensure we cannot crash if the GPIO device gets unregistered (and the
chip pointer set to NULL) during any of the API calls.
To that end: wait for all users of gdev->chip to exit their read-only
SRCU critical sections in gpiochip_remove().
For brevity: add a guard class which can be instantiated at the top of
every function requiring read-only access to the chip pointer and use it
in all API calls taking a GPIO descriptor as argument. In places where
we only deal with the GPIO device - use regular guard() helpers and
rcu_dereference() for chip access. Do the same in API calls taking a
const pointer to gpio_desc.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add the SRCU struct to GPIO device. It will be used to serialize access
to the GPIO chip pointer. Initialize and clean it up where applicable.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Duplicating the can_sleep value in GPIO device will allow us to not
needlessly dereference the chip pointer in several places and reduce the
number of SRCU read-only critical sections.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need to check the gdev pointer in struct gpio_desc - it's
always assigned and never cleared. It's also pointless to check
gdev->chip before we actually serialize access to it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Checking desc->gdev->chip for NULL without holding it in place with some
serializing mechanism is pointless. Remove this check. Also don't check
desc->gdev for NULL as it can never happen. We'll be protecting
gdev->chip with SRCU soon but we will provide a dedicated, automatic
class for that.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need to dereference gdev->chip in gpiochip_setup_dev() as at
the time it's called, the label in the associated struct gpio_device is
already set.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Don't dereference gdev->chip if the same information can be obtained
from struct gpio_device.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The variable holding the number of GPIO lines is duplicated in GPIO
device so read it instead of unnecessarily dereferencing the chip
pointer.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
gpio_device_get_desc() is the safer alternative to gpiochip_get_desc().
As we don't really need to dereference the chip pointer to retrieve the
descriptors in character device code, let's use it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We're working towards protecting the chip pointer in struct gpio_device
with SRCU. In order to use it in sysfs callbacks we must pass the pointer
to the GPIO device that wraps the chip instead of the address of the
chip itself as the user data.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Checking the gdev->mockdev pointer for NULL must be part of the critical
section.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We now removed the gpio_lock spinlock and modified the places
previously protected by it to handle desc->flags access in a consistent
way. Let's improve other places that were previously unprotected by
reading the flags field of gpio_desc once and using the stored value for
logic consistency. If we need to modify the field, let's also write it
back once with a consistent value resulting from the function's logic.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The "multi-function" gpio_lock is pretty much useless with how it's used
in GPIOLIB currently. Because many GPIO API calls can be called from all
contexts but may also call into sleeping driver callbacks, there are
many places with utterly broken workarounds like yielding the lock to
call a possibly sleeping function and then re-acquiring it again without
taking into account that the protected state may have changed.
It was also used to protect several unrelated things: like individual
descriptors AND the GPIO device list. We now serialize access to these
two with SRCU and so can finally remove the spinlock.
There is of course the question of consistency of lockless access to
GPIO descriptors. Because we only support exclusive access to GPIOs
(officially anyway, I'm looking at you broken
GPIOD_FLAGS_BIT_NONEXCLUSIVE bit...) and the API contract with providers
does not guarantee serialization, it's enough to ensure we cannot
accidentally dereference an invalid pointer and that the state we present
to both users and providers remains consistent. To achieve that: read the
flags field atomically except for a few special cases. Read their current
value before executing callback code and use this value for any subsequent
logic. Modifying the flags depends on the particular use-case and can
differ. For instance: when requesting a GPIO, we need to set the
REQUESTED bit immediately so that the next user trying to request the
same line sees -EBUSY.
While at it: the allocations that used GFP_ATOMIC until this point can
now switch to GFP_KERNEL.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
With the list of GPIO devices now protected with SRCU we can use
gpio_device_find() to traverse it from sysfs.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In order to ensure that the label is not freed while it's being
accessed, let's protect it with SRCU and synchronize it everytime it's
changed.
Let's modify desc_set_label() to manage the memory used for the label as
it can only be freed once synchronize_srcu() returns.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Extend the GPIO descriptor with an SRCU structure in order to serialize
the access to the label. Initialize and clean it up where applicable.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We will soon serialize access to the descriptor label using SRCU. The
write-side of the protection will require calling synchronize_srcu()
which must not be called from atomic context. We have two irq helpers:
gpiochip_lock_as_irq() and gpiochip_unlock_as_irq() that set the label
if the GPIO is not requested but is being used as interrupt. They are
called with a spinlock held from the interrupt subsystem.
They must not do it if we are to use SRCU so instead let's move the
special corner case to a dedicated getter.
Don't actually set the label to "interrupt" in the above case but rather
use the newly added gpiod_get_label() helper to hide the logic that
atomically checks the descriptor flags and returns the address of a
static "interrupt" string.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We will soon serialize access to the descriptor label using SRCU. The
write-side of the protection will require calling synchronize_srcu()
which must not be called from atomic context. We have two irq helpers:
gpiochip_lock_as_irq() and gpiochip_unlock_as_irq() that set the label
if the GPIO is not requested but is being used as interrupt. They are
called with a spinlock held from the interrupt subsystem.
They must not do it if we are to use SRCU so instead let's move the
special corner case to a dedicated getter.
First: let's implement and use the getter where it's applicable.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The general rule of the kernel is to not provide symbols that have no
users upstream. Let's remove logging helpers that are not used anywhere.
This will save us work later when we'll be modifying them to use the
upcoming SRCU infrastructure.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The device nodes representing GPIO hogs cannot be deleted without
unregistering the GPIO chip so there's no need to serialize their access.
However we must ensure that users can get the right address so write and
read it atomically.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We're working towards removing the "multi-function" GPIO spinlock that's
implemented terribly wrong. We tried using an RW-semaphore to protect
the list of GPIO devices but it turned out that we still have old code
using legacy GPIO calls that need to translate the global GPIO number to
the address of the associated descriptor and - to that end - traverse
the list while holding the lock. If we change the spinlock to a sleeping
lock then we'll end up with "scheduling while atomic" bugs.
Let's allow lockless traversal of the list using SRCU and only use the
mutex when modyfing the list.
While at it: let's protect the period between when we start the lookup
and when we finally request the descriptor (increasing the reference
count of the GPIO device) with the SRCU read lock.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The match function used in gpio_device_find() should not modify the
contents of passed opaque pointer, because such modification would not
be necessary for actual matching and it could lead to quite unreadable,
spaghetti code.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Bartosz: fix coding style in header]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmXJK4UeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGHsYH/jKmzKXDRsBCcw/Q
HGUvFtpohWBOpN6efdf0nxilQisuyQrqKB9fnwvfcdE60VpqMJXFMdlFh/fonxPl
JMbpk9y5uw48IJZA43NwTxUrjZ4wyWzv4ZF6YWa+5WdTAJpPLEPhhnLxcHOKklMr
5Cm/7B/M7eB2BXBfc45b1pkKN22q9OXvjaKxZ+5wYmiMxS+GC8l8jiJ/WlHX78PR
eLgsa1v732f2D7YF75wVhaoYepR+QzA9wTKqhjMNCEaVc2PQhA2JRsBXEt84qEIa
FZigmf7LLc4ed9YA2XjRBZhAehe3cZVJZ1lasW37IATS921La2WfKuiysICJOtyT
bGjK8tk=
=Pt7W
-----END PGP SIGNATURE-----
Merge tag 'v6.8-rc4' into gpio/for-next
Linux 6.8-rc4
Pulling this for a bugfix upstream with which the gpio/for-next branch
conflicts.
It's useful to have the device type information for those sub-devices
that are actually GPIO chips registered with GPIOLIB. While at it: use
the device type struct to setup the release callback which is the
preferred way to use the device API.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 48e1b4d369 ("gpiolib: remove the GPIO device from the list
when it's unregistered") we remove the GPIO device entry from the global
list (used to order devices by their GPIO ranges) when unregistering the
chip, not when releasing the device. It will not happen when the last
reference is put anymore. This means, we need to remove it in error path
in gpiochip_add_data_with_key() unconditionally, without checking if the
device's .release() callback is set.
Fixes: 48e1b4d369 ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Now that the driver core can properly handle constant struct bus_type,
move the gpio_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Enable COMPILE_TEST for the vf610 gpio driver to support test builds on
systems without this hardware.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The vf610 gpio driver is enabled by default for all i.MX machines,
without any option to disable it in a board-specific config file.
Most i.MX chipsets have no hardware for this driver. Change the default
to enable GPIO_VF610 for SOC_VF610 and disable it otherwise.
Add a text description after the bool type, this makes the driver
selectable by make config etc.
Fixes: 30a35c07d9 ("gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There are no external users for the irq domain helpers so unexport them
and remove the prototypes from the driver header.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The locking wrappers were replaces with lock guards. These typedefs are
no longer needed.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
The raw interrupt status of eic maybe set before the interrupt is enabled,
since the eic interrupt has a latch function, which would trigger the
interrupt event once enabled it from user side. To solve this problem,
interrupts generated before setting the interrupt trigger type are ignored.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The num_eics is a default value, but some SoCs support more than 8.
In order to adapt to all projects, the total number of eics is
automatically calculated through dts.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Spurious wakeups are reported on the GPD G1619-04 which
can be absolved by programming the GPIO to ignore wakeups.
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Melikov <mail@gmelikov.ru>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3073
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We've recently had someone try to use of_get_named_gpio() in new code.
Mark legacy interfaces as deprecated in kernel docs to avoid any
confusion.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
- revert the changes aiming to use a read-write semaphore to protect the
list of GPIO devices due to calls to legacy API taking that lock from
atomic context in old code
- fix inverted logic in DEFINE_FREE() for GPIO device references
- check the return value of bgpio_init() in gpio-mlxbf3
- fix node address in the DT bindings example for gpio-xilinx
- fix signedness bug in gpio-rtd
- fix kernel-doc warnings in gpio-en7523
-----BEGIN PGP SIGNATURE-----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=g2QY
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"Apart from some regular driver fixes there's a relatively big revert
of the locking changes that were introduced to GPIOLIB in this merge
window.
This is because it turned out that some legacy GPIO interfaces - that
need to translate a number from the global GPIO numberspace to the
address of the relevant descriptor, thus running a GPIO device lookup
and taking the GPIO device list lock - are still used in old code from
atomic context resulting in "scheduling while atomic" errors.
I'll try to make the read-only part of the list access entirely
lockless using SRCU but this will take some time so let's go back to
the old global spinlock for now.
Summary:
- revert the changes aiming to use a read-write semaphore to protect
the list of GPIO devices due to calls to legacy API taking that
lock from atomic context in old code
- fix inverted logic in DEFINE_FREE() for GPIO device references
- check the return value of bgpio_init() in gpio-mlxbf3
- fix node address in the DT bindings example for gpio-xilinx
- fix signedness bug in gpio-rtd
- fix kernel-doc warnings in gpio-en7523"
* tag 'gpio-fixes-for-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: revert the attempt to protect the GPIO device list with an rwsem
gpio: EN7523: fix kernel-doc warnings
gpiolib: Fix scope-based gpio_device refcounting
gpio: mlxbf3: add an error code check in mlxbf3_gpio_probe
dt-bindings: gpio: xilinx: Fix node address in gpio
gpio: rtd: Fix signedness bug in probe
- Add support for Monolithic Power Systems MP3309C WLED Step-up Converter
- Fix-ups
- Use/convert to new/better APIs/helpers/MACROs instead of hand-rolling implementations
- Device Tree Binding updates
- Demote non-kerneldoc header comments
- Improve error handling; return proper error values, simplify, avoid duplicates, etc
- Convert over to the new (kinda) GPIOD API
- Bug Fixes
- Fix uninitialised local variable
-----BEGIN PGP SIGNATURE-----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=SXS0
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Drivers:
- Add support for Monolithic Power Systems MP3309C WLED Step-up Converter
Fix-ups:
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree Binding updates
- Demote non-kerneldoc header comments
- Improve error handling; return proper error values, simplify, avoid
duplicates, etc
- Convert over to the new (kinda) GPIOD API
Bug Fixes:
- Fix uninitialised local variable"
* tag 'backlight-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: hx8357: Convert to agnostic GPIO API
backlight: ili922x: Add an error code check in ili922x_write()
backlight: ili922x: Drop kernel-doc for local macros
backlight: mp3309c: Fix uninitialized local variable
backlight: pwm_bl: Use dev_err_probe
backlight: mp3309c: Add support for MPS MP3309C
dt-bindings: backlight: mp3309c: Remove two required properties
This reverts commits 1979a28075 ("gpiolib: replace the GPIO device
mutex with a read-write semaphore") and 65a828bab1 ("gpiolib: use
a mutex to protect the list of GPIO devices").
Unfortunately the legacy GPIO API that's still used in older code has to
translate numbers from the global GPIO numberspace to descriptors. This
results in a GPIO device lookup in every call to legacy functions. Some
of those functions - like gpio_set/get_value() - can be called from
atomic context so taking a sleeping lock that is an RW semaphore results
in an error.
We'll probably have to protect this list with SRCU.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-wireless/f7b5ff1e-8f34-4d98-a7be-b826cb897dc8@moroto.mountain/
Fixes: 1979a28075 ("gpiolib: replace the GPIO device mutex with a read-write semaphore")
Fixes: 65a828bab1 ("gpiolib: use a mutex to protect the list of GPIO devices")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add "struct" keyword and explain the @dir array differently to
prevent kernel-doc warnings:
gpio-en7523.c:22: warning: cannot understand function prototype: 'struct airoha_gpio_ctrl '
gpio-en7523.c:27: warning: Function parameter or struct member 'dir' not described in 'airoha_gpio_ctrl'
gpio-en7523.c:27: warning: Excess struct member 'dir0' description in 'airoha_gpio_ctrl'
gpio-en7523.c:27: warning: Excess struct member 'dir1' description in 'airoha_gpio_ctrl'
Fixes: 0868ad385a ("gpio: Add support for Airoha EN7523 GPIO controller")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Clang static checker warning: Value stored to 'ret' is never read.
bgpio_init() returns error code if failed, it's better to add this
check.
Fixes: cd33f216d2 ("gpio: mlxbf3: Add gpio driver support")
Signed-off-by: Su Hui <suhui@nfschina.com>
[Bartosz: add the Fixes: tag]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The "data->irqs[]" array holds unsigned int so this error handling will
not work correctly.
Fixes: eee636bff0 ("gpio: rtd: Add support for Realtek DHC(Digital Home Center) RTD SoCs")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
