The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The simple_write_to_buffer() function will return positive/success if it
is able to write a single byte anywhere within the buffer. However that
potentially leaves a lot of the buffer uninitialized.
In this code it's better to return 0 if the offset is non-zero. This
code is not written to support partial writes. And then return -EFAULT
if the buffer is not completely initialized.
Fixes: cfad642538 ("eeprom: Add IDT 89HPESx EEPROM/CSR driver")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Ysg1Pu/nzSMe3r1q@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
see warnings:
| drivers/misc/eeprom/idt_89hpesx.c:570:5: error: format specifies type
| 'unsigned char' but the argument has type 'u16' (aka 'unsigned short')
| [-Werror,-Wformat] memaddr);
-
| drivers/misc/eeprom/idt_89hpesx.c:579:5: error: format specifies type
| 'unsigned char' but the argument has type 'u16' (aka 'unsigned short')
| [-Werror,-Wformat] memaddr);
-
| drivers/misc/eeprom/idt_89hpesx.c:814:4: error: format specifies type
| 'unsigned short' but the argument has type 'unsigned int'
| [-Werror,-Wformat] CSR_REAL_ADDR(csraddr));
There's an ongoing movement to eventually enable the -Wformat flag for
clang. See: https://github.com/ClangBuiltLinux/linux/issues/378
The format specifier for idt_89hpesx.c:570 and 579 was `0x%02hhx`. The
part we care about `%hhx` describes a single byte format, wherein the
leftmost byte of our u16 type (of which memaddr is) is truncated.
example:
```
uint16_t x = 0xbabe;
printf("%hhx\n", x);
// output is: be
// we lost 'ba'
```
There exists a similar issue at idt_89hpesx.c:814 which involves the
CSR_REAL_ADDR macro. This macro returns a u16 but due to default
argument promotion for variadic functions (printf-like) actually
provides an int to the dev_err method.
My proposed solution is to expand the width of the format specifier to
fully encompass the provided argument (which is promoted to an int, see
below). I opted for '%x' as this specifies an unsigned hexadecimal
integer which, with a guarantee, can represent all the values of a u16.
As per C11 6.3.1.1:
(https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf)
`If an int can represent all values of the original type ..., the
value is converted to an int; otherwise, it is converted to an
unsigned int. These are called the integer promotions.`
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20220701232031.2639134-1-justinstitt@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent change to split reads into chunks has several problems:
1. If an SPI controller has no transfer size limit, max_chunk is
SIZE_MAX, and num_msgs becomes zero, causing no data to be read
into the buffer, and exposing the original contents of the buffer
to userspace,
2. If the requested read size is not a multiple of the maximum
transfer size, the last transfer reads too much data, overflowing
the buffer,
3. The loop logic differs from the write case.
Fix the above by:
1. Keeping track of the number of bytes that are still to be
transferred, instead of precalculating the number of messages and
keeping track of the number of bytes tranfered,
2. Calculating the transfer size of each individual message, taking
into account the number of bytes left,
3. Switching from a "while"-loop to a "do-while"-loop, and renaming
"msg_count" to "segment".
While at it, drop the superfluous cast from "unsigned int" to "unsigned
int", also from at25_ee_write(), where it was probably copied from.
Fixes: 0a35780c75 ("eeprom: at25: Split reads into chunks and cap write size")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7ae260778d2c08986348ea48ce02ef148100e088.1655817534.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of spi_max_transfer_size to avoid requesting transfers that are
too large for some spi controllers.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220524215142.60047-1-eajames@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus types,
causing updates to most SPI device drivers. The branch with that on has
been cross merged with a couple of other trees which added new SPI
drivers this cycle, I'm not expecting any build issues resulting from
the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4b+8ACgkQJNaLcl1U
h9AB+Qf/WhPzDSCdhK1repnSmEpRNs/J6hItmY2H6pTQaWALpfTB0+p1Nb5tAotg
fHbu6a2AsiiwWt+tDal44GFYhS0CDSOT4hqgLV8msyDDPPJqqr7A2dbu7YrCjTVI
TgNZNwxW7c2LgqBXR9GV7NPWYoxYxveoYh+L+05MSuSQxSOvPl6LUZiZPnPufQM6
dCpEh19atrtasFg3rFnslWBd2C3h8hb6YT7vUZs9gxhg3FvSgpYQwzz5SfFgHXK6
Rg07m8fDTSjf2qo1C4pc/d1Ni1xBe7aHKMtjtR3jJ4q8QqiawfCcvvOep/Iaec1+
s3qnDthohWMJoF1W6ERf3HiAgNIfhg==
=4tlR
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Merge 5.17-rc4 into char-misc-next
We need the char/misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit effa453168 ("i2c: i801: Don't silently correct invalid transfer
size") revealed that ee1004_eeprom_read() did not properly limit how
many bytes to read at once.
In particular, i2c_smbus_read_i2c_block_data_or_emulated() takes the
length to read as an u8. If count == 256 after taking into account the
offset and page boundary, the cast to u8 overflows. And this is common
when user space tries to read the entire EEPROM at once.
To fix it, limit each read to I2C_SMBUS_BLOCK_MAX (32) bytes, already
the maximum length i2c_smbus_read_i2c_block_data_or_emulated() allows.
Fixes: effa453168 ("i2c: i801: Don't silently correct invalid transfer size")
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20220203165024.47767-1-jonas@protocubo.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmH2lIMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWzkH/jmR4RpGgrV5SUHF
8R6tsIjae1WItJ8NoaDgImWRxLKXFU7MM77HoFykuZx5Y5yz5Xf5zuJNXRPrHQbC
lE/8wqWut89LX0+k/pKSzt8BQbyZzImfm5rOSBpMC9VkvMcbuQ8NSJ/YbJOD4iAp
jfRRIkJtLQWL6YRc/xPlHCfVY5Qx+TkNZuFFckPtM2HKIEXS225VCESX9JcABDcQ
j7zG5bq/H+8qGItD2iUg8Nw9hqrLutdKSOgP29wxVOajY5QWVczYr1J0nfyRSPMb
/Xs1Oo1/+zO+dfCmR45puJZYua+e/iFTJv2RPFLRIE2AV1vMq4WNIgTJlq8DwfQK
C7Jq080=
=6u+c
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc2' into char-misc-next
We need the char/misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The at25 driver regressed in v5.17-rc1 due to a broken conflict
resolution: the allocation of the object was accidentally removed. Restore
it.
This was found when building under CONFIG_FORTIFY_SOURCE=y and
-Warray-bounds, which complained about strncpy() being used against an
empty object:
In function 'strncpy',
inlined from 'at25_fw_to_chip.constprop' at drivers/misc/eeprom/at25.c:312:2:
./include/linux/fortify-string.h:48:33: warning: '__builtin_strncpy' offset [0, 9] is out of the bounds [0, 0] [-Warray-bounds]
48 | #define __underlying_strncpy __builtin_strncpy
| ^
./include/linux/fortify-string.h:59:16: note: in expansion of macro '__underlying_strncpy'
59 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
In function 'strncpy',
inlined from 'at25_fram_to_chip' at drivers/misc/eeprom/at25.c:373:2,
inlined from 'at25_probe' at drivers/misc/eeprom/at25.c:453:10:
./include/linux/fortify-string.h:48:33: warning: '__builtin_strncpy' offset [0, 9] is out of the bounds [0, 0] [-Warray-bounds]
48 | #define __underlying_strncpy __builtin_strncpy
| ^
./include/linux/fortify-string.h:59:16: note: in expansion of macro '__underlying_strncpy'
59 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/lkml/CAHp75VdqK7h63fz-cPaQ2MGaVdaR2f1Fb5kKCZidUG3RwLsAVA@mail.gmail.com/
Fixes: af40d16042 ("Merge v5.15-rc5 into char-misc-next")
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220118182003.3385019-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull i2c updates from Wolfram Sang:
"Mostly driver updates and refactorization.
The removal of the XLR driver and the i801 refactoring stand out a
little. In the core, we enabled async suspend/resume for I2C
controllers and their clients. No issues were reported during the test
phase in -next. We will see how this goes for mainline"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (54 commits)
i2c: sh_mobile: remove unneeded semicolon
i2c: riic: Use platform_get_irq() to get the interrupt
i2c: sh_mobile: Use platform_get_irq_optional() to get the interrupt
i2c: bcm2835: Use platform_get_irq() to get the interrupt
i2c: aspeed: Remove unused includes
dt-bindings: i2c: aspeed: Drop stray '#interrupt-cells'
i2c: sh_mobile: update to new DMAENGINE API when terminating
i2c: rcar: update to new DMAENGINE API when terminating
i2c: exynos5: Fix getting the optional clock
i2c: designware-pci: Convert to use dev_err_probe()
i2c: designware-pci: use __maybe_unused for PM functions
i2c: designware-pci: Group MODULE_*() macros
i2c: designware-pci: Add a note about struct dw_scl_sda_cfg usage
i2c: designware-pci: Fix to change data types of hcnt and lcnt parameters
i2c: designware: Do not complete i2c read without RX_FULL interrupt
eeprom: at24: Add support for 24c1025 EEPROM
dt-bindings: at24: add at24c1025
i2c: tegra: use i2c_timings for bus clock freq
dt-bindings: at24: Rework special case compatible handling
i2c: i801: Don't clear status flags twice in interrupt mode
...
Microchip EEPROM 24xx1025 is like a 24c1024. The only difference
between them is that the I2C address bit used to select between the
two banks is bit 2 for the 1025 and not bit 0 as in the 1024.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
We need the fixes in here as well, and also resolve some merge conflicts
in:
drivers/misc/eeprom/at25.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make multi-line comment style aligned.
While at it, drop filename from the file.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125213203.86693-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split headers to three groups and sort alphabetically in each of them.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125213203.86693-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the similar way as it's done for EEPROM, factor out
a new helper function for FRAM.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125213203.86693-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's obvious that custom approach of getting power of 2 number with
int_pow() kinda interesting. Replace it and some others approaches
by using a simple BIT() operation.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125213203.86693-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to copy twice the same data. Drop needless local
variable.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125213203.86693-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Access to platform data via dev_get_platdata() getter to make code cleaner.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125213203.86693-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_property_read_u32() may return different error codes.
Unshadow them in the at25_fw_to_chip() to give better error
report.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125213203.86693-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently some values are compared against the contents of the chip structure
and most are from its updated copy in at25->chip. Use the latter one everywhere
in ->probe().
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125213203.86693-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obviously the byte_len value should be checked from the chip
and not from at25->chip.
Fixes: fd307a4ad3 ("nvmem: prepare basics for FRAM support")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125212729.86585-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if we know that we are going to fill everything later on
it's bad style and fragile to copy garbage from the stack to
the data structure that will be used in the driver.
Fixes: fd307a4ad3 ("nvmem: prepare basics for FRAM support")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125212729.86585-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit f60e707490 ("misc: at25: Make use of device property API")
made a good job by enabling the driver for non-OF platforms, but the
recent commit 604288bc61 ("nvmem: eeprom: at25: fix type compiler warnings")
brought that back.
Restore greatness of the driver once again.
Fixes: eab61fb1cc ("nvmem: eeprom: at25: fram discovery simplification")
Fixes: fd307a4ad3 ("nvmem: prepare basics for FRAM support")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211125212729.86585-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fd307a4ad3 ("nvmem: prepare basics for FRAM support") added
support for FRAM devices such as the Cypress FM25V. During testing, it
was found that the FRAM detects properly, however reads and writes fail.
Upon further investigation, two problem were found in at25_probe() routine.
1) In the case of an FRAM device without platform data, eg.
fram == true && spi->dev.platform_data == NULL
the stack local variable "struct spi_eeprom chip" is not initialized
fully, prior to being copied into at25->chip. The chip.flags field in
particular can cause problems.
2) The byte_len of FRAM is computed from its ID register, and is stored
into the stack local "struct spi_eeprom chip" structure. This happens
after the same structure has been copied into at25->chip. As a result,
at25->chip.byte_len does not contain the correct length of the device.
In turn this can cause checks at beginning of at25_ee_read() to fail
(or equally, it could allow reads beyond the end of the device length).
Fix both of these issues by eliminating the on-stack struct spi_eeprom.
Instead use the one inside at25_data structure, which starts of zeroed.
Fixes: fd307a4ad3 ("nvmem: prepare basics for FRAM support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Link: https://lore.kernel.org/r/20211108181627.645638-1-ralph.siemsen@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use member client only to get a reference to the associated struct
device, via &client->dev. However we can get the same reference from
the associated regmap, via regmap_get_device(regmap).
Therefore struct at24_client can be removed and replaced with a regmap
pointer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
In certain use cases (where the chip is part of a camera module, and the
camera module is wired together with a camera privacy LED), powering on
the device during probe is undesirable. Add support for the at24 to
execute probe while being in ACPI D state other than 0 (which means fully
powered on).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The newly added SPI device ID table does not work because the
entry is incorrectly copied from the OF device table.
During build testing, this shows as a compile failure when building
it as a loadable module:
drivers/misc/eeprom/eeprom_93xx46.c:424:1: error: redefinition of '__mod_of__eeprom_93xx46_of_table_device_table'
MODULE_DEVICE_TABLE(of, eeprom_93xx46_of_table);
Change the entry to refer to the correct symbol.
Fixes: 137879f7ff ("eeprom: 93xx46: Add SPI device ID table")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211014153730.3821376-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210922184048.34770-1-broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210923172453.4921-1-broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to append device id even if eeprom have a label property set as some
platform can have multiple eeproms with same label and we can not register
each of those with same label. Failing to register those eeproms trigger
cascade failures on such platform (system is no longer working).
This fix regression on such platform introduced with 4e302c3b56
Reported-by: Alexander Fomichev <fomichev.ru@gmail.com>
Fixes: 4e302c3b56 ("misc: eeprom: at24: fix NVMEM name with custom AT24 device name")
Cc: stable@vger.kernel.org
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fixes:
drivers/misc/eeprom/at25.c:181:28: warning: field width should have type 'int', but argument has type 'unsigned long'
drivers/misc/eeprom/at25.c:386:13: warning: cast to smaller integer type 'int' from 'const void *'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Fixes: fd307a4ad3 ("nvmem: prepare basics for FRAM support")
Link: https://lore.kernel.org/r/20210611142706.27336-1-jiri.prchal@aksignal.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added enum and string for FRAM (ferroelectric RAM) to expose it as file
named "fram".
Added documentation of sysfs file.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Link: https://lore.kernel.org/r/20210611094601.95131-2-jiri.prchal@aksignal.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When iterating over child firmware nodes restore printing the name of ones
that are not supported.
While at it, refactor loop body to clearly show that we stop at the first match.
Fixes: db15d73e5f ("eeprom: idt_89hpesx: Support both ACPI and OF probing")
Cc: Huy Duong <qhuyduong@hotmail.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210607221757.81465-2-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: db15d73e5f ("eeprom: idt_89hpesx: Support both ACPI and OF probing")
Cc: Huy Duong <qhuyduong@hotmail.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210607221757.81465-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving the call to ee1004_set_current_page() to ee1004_eeprom_read()
allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/2829a131-51e3-8865-462a-564080158b0b@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of ee1004_current_page applies to all SPD eeproms connected
to the adapter. Therefore it's sufficient if we set ee1004_current_page
when the first device is added.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/b9240e58-08bb-3d71-7a9c-9a323b470ab6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_new_dummy_device() calls i2c_new_client_device() that complains
if it fails to create the device. Therefore we don't have to emit an
error message in case of failure. In addition ensure that
ee1004_set_page is only set if creating the device succeeded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/d38df5ac-6ecb-7d5f-b5c3-39bfc6a1e8a1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have to read 512 bytes only, therefore read performance isn't really
a concern. Don't bother the user if i2c block read isn't supported.
For i2c_smbus_read_i2c_block_data_or_emulated() to work it's sufficient
if I2C_FUNC_SMBUS_READ_I2C_BLOCK or I2C_FUNC_SMBUS_READ_BYTE_DATA is
supported. Therefore remove the check for I2C_FUNC_SMBUS_READ_WORD_DATA.
In addition check for I2C_FUNC_SMBUS_WRITE_BYTE (included in
I2C_FUNC_SMBUS_BYTE) which is needed for setting the page.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/840c668e-6310-e933-e50e-5abeaecfb39c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_smbus_read_i2c_block_data_or_emulated() checks its length argument,
so we don't have to do it. In addition remove the unlikely hint from
the checks, we do i2c reads and therefore are in a slow path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/eb2a8bff-43ec-c763-a417-9d741e6f0034@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sysfs_kf_bin_read() checks this for us already. In addition
the function works correctly also w/o this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/33889bff-3614-4b73-5010-701635e1edab@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of creating/removing the attribute ourselves, just declare the
attribute and let the device core handle it. This allows to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8a6c77f2-f84a-311b-c2b9-21798f690e4d@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cd5676db05 ("misc: eeprom: at24: support pm_runtime control") disables
regulator in runtime suspend. If runtime suspend is called before
regulator disable, it will results in regulator unbalanced disabling.
Fixes: cd5676db05 ("misc: eeprom: at24: support pm_runtime control")
Cc: stable <stable@vger.kernel.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210420133050.377209-1-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two devices have respectively 2048 and 4096 bits of storage,
compared to 1024 for the 93c46.
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Link: https://lore.kernel.org/r/20210511210727.24895-3-linkmauve@linkmauve.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids using magic numbers based on the length of an address or a
command, while we only want to differentiate between 8-bit and 16-bit.
The driver was previously wrapping around the offset in the write
operation, this now returns -EINVAL instead (but should never happen in
the first place).
If two pointer indirections are too many, we could move the flags to the
main struct instead, but I doubt it’s going to make any sensible
difference on any hardware.
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Link: https://lore.kernel.org/r/20210511210727.24895-2-linkmauve@linkmauve.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A dummy zero bit is sent preceding the data during a read transfer by the
Microchip 93LC46B eeprom (section 2.7 of[1]). This results in right shift
of data during a read. In order to ignore this bit a quirk can be added to
send an extra zero bit after the read address.
Add a quirk to ignore the zero bit sent before data by adding a zero bit
after the read address.
[1] - https://www.mouser.com/datasheet/2/268/20001749K-277859.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210105105817.17644-3-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Module alias "spi:93xx46" is used by non device tree users like
drivers/misc/eeprom/digsy_mtc_eeprom.c and removing it will
break support for them.
Fix this by adding back the module alias "spi:93xx46".
Fixes: 13613a2246 ("misc: eeprom_93xx46: Fix module alias to enable module autoprobe")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210113051253.15061-1-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add module alias to enable autoprobe for microchip 93LC46B eeprom by using
/sys/class/.../spi1.0/modalias content.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210107163957.28664-3-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix module autoprobe by correcting module alias to match the string from
/sys/class/.../spi1.0/modalias content.
Fixes: 06b4501e88 ("misc/eeprom: add driver for microwire 93xx46 EEPROMs")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210107163957.28664-2-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
When the "label" property is set on the AT24 EEPROM the NVMEM devid is
set to NVMEM_DEVID_NONE, but it is not effective since there is a
leftover line setting it back to NVMEM_DEVID_AUTO a few lines after.
Fixes: 61f764c307 ("eeprom: at24: Support custom device names for AT24 EEPROMs")
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
To save the interested reader some time, add examples of AT25 part
numbers that correspond to EEPROMs rather than flashes.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20201107133337.1066271-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull i2c updates from Wolfram Sang:
- if a host can be a client, too, the I2C core can now use it to
emulate SMBus HostNotify support (STM32 and R-Car added this so far)
- also for client mode, a testunit has been added. It can create rare
situations on the bus, so host controllers can be tested
- a binding has been added to mark the bus as "single-master". This
allows for better timeout detections
- new driver for Mellanox Bluefield
- massive refactoring of the Tegra driver
- EEPROMs recognized by the at24 driver can now have custom names
- rest is driver updates
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (80 commits)
Documentation: i2c: add testunit docs to index
i2c: tegra: Improve driver module description
i2c: tegra: Clean up whitespaces, newlines and indentation
i2c: tegra: Clean up and improve comments
i2c: tegra: Clean up printk messages
i2c: tegra: Clean up variable names
i2c: tegra: Improve formatting of variables
i2c: tegra: Check errors for both positive and negative values
i2c: tegra: Factor out hardware initialization into separate function
i2c: tegra: Factor out register polling into separate function
i2c: tegra: Factor out packet header setup from tegra_i2c_xfer_msg()
i2c: tegra: Factor out error recovery from tegra_i2c_xfer_msg()
i2c: tegra: Rename wait/poll functions
i2c: tegra: Remove "dma" variable from tegra_i2c_xfer_msg()
i2c: tegra: Remove redundant check in tegra_i2c_issue_bus_clear()
i2c: tegra: Remove likely/unlikely from the code
i2c: tegra: Remove outdated barrier()
i2c: tegra: Clean up variable types
i2c: tegra: Reorder location of functions in the code
i2c: tegra: Clean up probe function
...
- add support for masking sensitive data in VAIO EEPROMs
- set the nvmem TYPE to NVMEM_TYPE_EEPROM
- add support for the new 'label' property
- set the nvmem ID to NVMEM_DEVID_AUTO by default (for backward
compatibility) or to NVMEM_DEVID_NONE if label is defined
-----BEGIN PGP SIGNATURE-----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=KexW
-----END PGP SIGNATURE-----
Merge tag 'at24-updates-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.10
at24 updates for v5.10
- add support for masking sensitive data in VAIO EEPROMs
- set the nvmem TYPE to NVMEM_TYPE_EEPROM
- add support for the new 'label' property
- set the nvmem ID to NVMEM_DEVID_AUTO by default (for backward
compatibility) or to NVMEM_DEVID_NONE if label is defined
By using the label property, a more descriptive name can be populated
for AT24 EEPROMs NVMEM device. Update the AT24 driver to check to see
if the label property is present and if so, use this as the name for
NVMEM device. Please note that when the 'label' property is present for
the AT24 EEPROM, we do not want the NVMEM driver to append the 'devid'
to the name and so the nvmem_config.id is initialised to
NVMEM_DEVID_NONE.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The AT24 EEPROM driver does not initialise the 'id' field of the
nvmem_config structure and because the entire structure is not
initialised, it ends up with a random value. This causes the NVMEM
driver to append the device 'devid' value to name of the NVMEM
device. Ideally for I2C devices such as the AT24 that already have a
unique name, we would not bother to append the 'devid'. However, given
that this has always been done for AT24 devices, we cannot remove the
'devid' as this will change the name of the userspace sysfs node for
the NVMEM device. Nonetheless we should ensure that the 'id' field of
the nvmem_config structure is initialised so that there is no chance of
a random value causes problems in the future. Therefore, set the NVMEM
config.id to NVMEM_DEVID_AUTO for AT24 EEPROMs so that the 'devid' is
always appended.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Slightly easier to read.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Set type as NVMEM_TYPE_EEPROM to expose this info via
sysfs:
$ cat /sys/bus/nvmem/devices/{DEVICE}/type
EEPROM
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20200916170933.20302-4-vadym.kochan@plvision.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set type as NVMEM_TYPE_EEPROM to expose this info via
sysfs:
$ cat /sys/bus/nvmem/devices/{DEVICE}/type
EEPROM
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20200916170933.20302-3-vadym.kochan@plvision.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set type as NVMEM_TYPE_EEPROM to expose this info via
sysfs:
$ cat /sys/bus/nvmem/devices/{DEVICE}/type
EEPROM
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- delay registration of the nvmem provider until after power is enabled
-----BEGIN PGP SIGNATURE-----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=c7cP
-----END PGP SIGNATURE-----
Merge tag 'at24-fixes-for-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-current
at24 fixes for v5.9-rc5
- delay registration of the nvmem provider until after power is enabled
During nvmem_register() the nvmem core sends notifications when:
- cell added
- nvmem added
and during these notifications some callback func may access the nvmem
device, which will fail in case of at24 eeprom because regulator and pm
are enabled after nvmem_register().
Fixes: cd5676db05 ("misc: eeprom: at24: support pm_runtime control")
Fixes: b20eb4c1f0 ("eeprom: at24: drop unnecessary label")
Cc: stable@vger.kernel.org
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Storage technologies like FRAM have no "write pages", the whole chip can
be written within one SPI transfer. For these chips, the page size can
be set equal to the device size. Currently available devices are already
bigger than 64 kiB.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Link: https://lore.kernel.org/r/20200727111218.26926-1-ceggers@arri.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The elegant code in at24_read() has the drawback that we now need
to make a copy of all parameters to pass them to the post-processing
callback function if there is one. Rewrite the loop in such a way that
the parameters are not modified, so saving them is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Special handling of the Sony VAIO EEPROMs is the last feature of the
legacy eeprom driver that the at24 driver does not support. Adding
this would let us deprecate and eventually remove the legacy eeprom
driver.
So add the option to specify a post-processing callback function that
is called after reading data from the EEPROM, before it is returned
to the user. The 24c02-vaio type is the first use case of that option:
the callback function will mask the sensitive data for non-root users
exactly as the legacy eeprom driver was doing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Bartosz: removed a stray newline]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
... as is the case when !CONFIG_ACPI.
Fixes the following W=1 kernel build warning:
drivers/misc/eeprom/at24.c:228:36: warning: ‘at24_acpi_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200701093616.GX1179328@dell
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copy-paste issue. Looks like the kerneldoc style descriptions for
these functions were taken from existing functions with slightly
different argument names.
Fixes the following W=1 warnings:
drivers/misc/eeprom/eeprom_93cx6.c:239: warning: Function parameter or member 'byte' not described in 'eeprom_93cx6_readb'
drivers/misc/eeprom/eeprom_93cx6.c:239: warning: Excess function parameter 'word' description in 'eeprom_93cx6_readb'
drivers/misc/eeprom/eeprom_93cx6.c:280: warning: Function parameter or member 'bytes' not described in 'eeprom_93cx6_multireadb'
drivers/misc/eeprom/eeprom_93cx6.c:280: warning: Excess function parameter 'words' description in 'eeprom_93cx6_multireadb'
Cc: Wolfram Sang <wsa@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200626130525.389469-7-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The at24 driver attempts to read a byte from the device to validate that
it's actually present, and if not, disables the vcc regulator and
returns -ENODEV. However, between the read and the error handling path,
pm_runtime_idle() is called and invokes the driver's suspend callback,
which also disables the vcc regulator. This leads to an underflow of the
regulator enable count if the EEPROM is not present.
Move the pm_runtime_suspend() call to be after the error handling path
to resolve this.
Fixes: cd5676db05 ("misc: eeprom: at24: support pm_runtime control")
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This ID is used at leas on some variants of MSC C6B-SLH board.
Signed-off-by: Markus Pietrek <mpie@msc-ge.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Although in the most platforms, the power of eeprom are alway
on, some platforms disable the eeprom power in order to meet
low power request. This patch add the pm_runtime ops to control
power to support all platforms.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
[Bartosz: rebased on top of current at24/for-next]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
NVMEM framework is an interface for the at24 EEPROMs as well as for
other drivers, instead of passing the wp-gpios over the different
drivers each time, it would be better to pass it over the NVMEM
subsystem once and for all.
Removing the support for the write-protect pin after adding it to the
NVMEM subsystem.
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The current GPL v2.0 or later SPDX tag is 'GPL-2.0-or-later' as defined
at https://spdx.org/licenses/.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Pull i2c updates from Wolfram Sang:
"I2C has mostly driver updates this time.
The few noteworthy changes are: the core has now support for analog
and digital filters with at91 being the first user, a core addition to
replace the NULL returning i2c_new_probed_device() with an ERR_PTR
variant, and the pxa driver has finally being moved to use the generic
I2C slave interface. We have quite a significant number of reviews per
patch this time, so thank you to all involved!"
* 'i2c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
video: fbdev: matrox: convert to i2c_new_scanned_device
i2c: icy: convert to i2c_new_scanned_device
i2c: replace i2c_new_probed_device with an ERR_PTR variant
i2c: Fix Kconfig indentation
i2c: smbus: Don't filter out duplicate alerts
i2c: i801: Correct Intel Jasper Lake SOC naming
i2c: i2c-stm32f7: fix 10-bits check in slave free id search loop
i2c: iproc: Add i2c repeated start capability
i2c: remove helpers for ref-counting clients
i2c: tegra: Use dma_request_chan() directly for channel request
i2c: sh_mobile: Use dma_request_chan() directly for channel request
i2c: qup: Use dma_request_chan() directly for channel request
i2c: at91: Use dma_request_chan() directly for channel request
i2c: rcar: Remove superfluous call to clk_get_rate()
i2c: pxa: remove unused i2c-slave APIs
i2c: pxa: migrate to new i2c_slave APIs
i2c: cros-ec-tunnel: Make the device acpi compatible
i2c: stm32f7: report dma error during probe
i2c: icy: no need to populate address for scanned device
i2c: xiic: Fix kerneldoc warnings
...
