On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.
On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD card is allowed to signal busy on DAT0 up to 1s after the
CMD49. According to SD spec (version 6.0 section 5.8.1.3) first host
waits until busy of CMD49 is released and only then polls Power
Management Status register up to 1s until the card indicates ready to
power off.
Without waiting for busy before polling status register sometimes card
becomes unresponsive and system fails to suspend:
[ 205.907459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 206.421274] sunxi-mmc 1c0f000.mmc: data error, sending stop command
[ 206.421321] sunxi-mmc 1c0f000.mmc: send stop command failed
[ 206.421347] mmc0: error -110 reading status reg of PM func
[ 206.421366] PM: dpm_run_callback(): mmc_bus_suspend+0x0/0x74 returns -110
[ 206.421402] mmcblk mmc0:aaaa: PM: failed to suspend async: error -110
[ 206.437064] PM: Some devices failed to suspend, or early wake event detected
Tested with Sandisk Extreme PRO A2 64GB on Allwinner A64 system.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Fixes: 2c5d427690 ("mmc: core: Add support for Power Off Notification for SD cards")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220115121447.641524-1-andrej.skvortzov@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sparse spits out this following warning:
drivers/mmc/core/queue.c:311:21: warning: incorrect type in assignment (different base types)
drivers/mmc/core/queue.c:311:21: expected int ret
drivers/mmc/core/queue.c:311:21: got restricted blk_status_t [usertype]
drivers/mmc/core/queue.c:314:21: warning: incorrect type in assignment (different base types)
drivers/mmc/core/queue.c:314:21: expected int ret
drivers/mmc/core/queue.c:314:21: got restricted blk_status_t [usertype]
drivers/mmc/core/queue.c:336:16: warning: incorrect type in return expression (different base types)
drivers/mmc/core/queue.c:336:16: expected restricted blk_status_t
drivers/mmc/core/queue.c:336:16: got int [assigned] ret
ret is only used for blk_status_t types, so make it that type.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211215011336.194089-1-joel@jms.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's seems prone to problems by allowing card detect and its corresponding
mmc_rescan() work to run, during platform shutdown. For example, we may end
up turning off the power while initializing a card, which potentially could
damage it.
To avoid this scenario, let's add ->shutdown_pre() callback for the mmc host
class device and then turn of the card detect from there.
Reported-by: Al Cooper <alcooperx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211203141555.105351-1-ulf.hansson@linaro.org
If there is no driver match function, the driver core assumes that each
candidate pair (driver, device) matches, see driver_match_device().
Drop the mmc bus's match function that always returned 1 and so implements
the same behaviour as when there is no match function.
Signed-off-by: lizhe <sensor1010@163.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211207095029.96387-1-sensor1010@163.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In mmc_send_op_cond(), loops are continuously performed at the same
interval of 10 ms. However the behaviour is not good for some eMMC
which can be out from a busy state earlier than 10 ms if normal.
Rather than fixing about the interval time in mmc_send_op_cond(),
let's instead convert into using the common __mmc_poll_for_busy().
The reason for adjusting the interval time is that it is important
to reduce the eMMC initialization time, especially in devices that
use eMMC as rootfs.
Test log(eMMC:KLM8G1GETF-B041):
before: 12 ms (0.311016 - 0.298729)
[ 0.295823] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 0.298729] mmc0: starting CMD1 arg 40000080 flags 000000e1<-start
[ 0.311016] mmc0: starting CMD1 arg 40000080 flags 000000e1<-finish
[ 0.311336] mmc0: starting CMD2 arg 00000000 flags 00000007
after: 2 ms (0.301270 - 0.298762)
[ 0.295862] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 0.298762] mmc0: starting CMD1 arg 40000080 flags 000000e1<-start
[ 0.299067] mmc0: starting CMD1 arg 40000080 flags 000000e1
[ 0.299441] mmc0: starting CMD1 arg 40000080 flags 000000e1
[ 0.299879] mmc0: starting CMD1 arg 40000080 flags 000000e1
[ 0.300446] mmc0: starting CMD1 arg 40000080 flags 000000e1
[ 0.301270] mmc0: starting CMD1 arg 40000080 flags 000000e1<-finish
[ 0.301572] mmc0: starting CMD2 arg 00000000 flags 00000007
Signed-off-by: Huijin Park <huijin.park@samsung.com>
Link: https://lore.kernel.org/r/20211104063231.2115-3-huijin.park@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the __mmc_poll_for_busy() first parameter type
from 'struct mmc_card*' to 'struct mmc_host*'.
Because the function refers only 'struct mmc_host' to get hostname.
Signed-off-by: Huijin Park <huijin.park@samsung.com>
Link: https://lore.kernel.org/r/20211104063231.2115-2-huijin.park@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TiWi WL1251 WiFi chip needs special setup of the sdio
interface before it can be probed.
So far, this is done in omap_hsmmc_init_card() in omap_hsmmc.c
which makes it useable only if connected to omap devices
which use the omap_hsmmc. The OpenPandora is the most promient
example.
There are plans to switch to a newer sdhci-omap driver and
retire omap_hsmmc. Hence this quirk must be reworked or moved
somewhere else. Ideally to some location that is not dependent
on the specific SoC mmc host driver.
This is achieved by the new mmc_fixup_device() option introduced
by ("mmc: allow to match the device tree to apply quirks") to match
through device tree compatible string.
This quirk will be called early right after where host->ops->init_card()
and thus omap_hsmmc_init_card() was previously called.
Note that we do not need to transplant
card->ocr = 0x80;
because we rely on ("mmc: core: Fixup storing of OCR for MMC_QUIRK_NONSTD_SDIO").
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/774565df7f02124c003aaf8b879706352548f832.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This (initially empty) table allows to match quirks early based
on .compatible of the child node of some mmc/sdio interface.
This allows to add quirks based on device tree instead of having
card specific code in the host ops.
A new macro SDIO_FIXUP_COMPATIBLE makes the definition readable.
And we call mmc_fixup_device(sdio_card_init_methods) just after
where host->ops->init_card() can be optionally called.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/b13fd8b3eebc3c23b6816b254a518c224cbdcfd4.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC subsystem provides a way to apply quirks when a device match some
properties (VID, PID, etc...) Unfortunately, some SDIO devices do not
comply with the SDIO specification and does not provide reliable VID/PID
(eg. Silabs WF200).
So, the drivers for these devices rely on device tree to identify the
device.
This patch allows the MMC to also rely on the device tree to apply a
quirk.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/9e68e3d23e62a78527aabc1281f89e15200c7d09.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, mmc_fixup_device() is a bit difficult to read because of
particularly long condition.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/6515c1e8b3aa69ad273726f6e877d85c20f286ad.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the gendisk aregument to blk_execute_rq and blk_execute_rq_nowait
given that it is unused now. Also convert the boolean at_head parameter
to actually use the bool type while touching the prototype.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20211126121802.2090656-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just use the disk attached to the request_queue instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20211126121802.2090656-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The completion callback for the sdhci-pci device is invoked from a
kworker.
I couldn't identify in which context is mmc_blk_mq_req_done() invoke but
the remaining caller are from invoked from preemptible context. Here it
would make sense to complete the request directly instead scheduling
ksoftirqd for its completion.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211025070658.1565848-3-bigeasy@linutronix.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All modern drivers can support extra partitions using the extended
dev_t. In fact except for the ioctl method drivers never even see
partitions in normal operation.
So remove the GENHD_FL_EXT_DEVT and allow extra partitions for all
block devices that do support partitions, and require those that
do not support partitions to explicit disallow them using
GENHD_FL_NO_PART.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211122130625.1136848-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This manually reverts 07b652cdbec3 ("mmc: card: Don't show eMMC RPMB and
BOOT areas in /proc/partitions"). Based on the commit description that
change was purely cosmetic. mmc is the last driver that sets this
flag and thus prevents it from being removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20211122130625.1136848-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The GENHD_FL_NO_PART_SCAN controls more than just partitions canning,
so rename it to GENHD_FL_NO_PART.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20211122130625.1136848-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge misc updates from Andrew Morton:
"257 patches.
Subsystems affected by this patch series: scripts, ocfs2, vfs, and
mm (slab-generic, slab, slub, kconfig, dax, kasan, debug, pagecache,
gup, swap, memcg, pagemap, mprotect, mremap, iomap, tracing, vmalloc,
pagealloc, memory-failure, hugetlb, userfaultfd, vmscan, tools,
memblock, oom-kill, hugetlbfs, migration, thp, readahead, nommu, ksm,
vmstat, madvise, memory-hotplug, rmap, zsmalloc, highmem, zram,
cleanups, kfence, and damon)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (257 commits)
mm/damon: remove return value from before_terminate callback
mm/damon: fix a few spelling mistakes in comments and a pr_debug message
mm/damon: simplify stop mechanism
Docs/admin-guide/mm/pagemap: wordsmith page flags descriptions
Docs/admin-guide/mm/damon/start: simplify the content
Docs/admin-guide/mm/damon/start: fix a wrong link
Docs/admin-guide/mm/damon/start: fix wrong example commands
mm/damon/dbgfs: add adaptive_targets list check before enable monitor_on
mm/damon: remove unnecessary variable initialization
Documentation/admin-guide/mm/damon: add a document for DAMON_RECLAIM
mm/damon: introduce DAMON-based Reclamation (DAMON_RECLAIM)
selftests/damon: support watermarks
mm/damon/dbgfs: support watermarks
mm/damon/schemes: activate schemes based on a watermarks mechanism
tools/selftests/damon: update for regions prioritization of schemes
mm/damon/dbgfs: support prioritization weights
mm/damon/vaddr,paddr: support pageout prioritization
mm/damon/schemes: prioritize regions within the quotas
mm/damon/selftests: support schemes quotas
mm/damon/dbgfs: support quotas of schemes
...
nr_free_buffer_pages could be exposed through mm.h instead of swap.h.
The advantage of this change is that it can reduce the obsolete
includes. For example, net/ipv4/tcp.c wouldn't need swap.h any more
since it has already included mm.h. Similarly, after checking all the
other files, it comes that tcp.c, udp.c meter.c ,... follow the same
rule, so these files can have swap.h removed too.
Moreover, after preprocessing all the files that use
nr_free_buffer_pages, it turns out that those files have already
included mm.h.Thus, we can move nr_free_buffer_pages from swap.h to mm.h
safely. This change will not affect the compilation of other files.
Link: https://lkml.kernel.org/r/20210912133640.1624-1-liumh1@shanghaitech.edu.cn
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Cc: Jakub Kicinski <kuba@kernel.org>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Simon Horman <horms@verge.net.au>
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Update maintainer and URL for the mmc-utils
- Set default label for slot-gpio in case of no con-id
- Convert MMC card DT bindings to a schema
- Add optional host specific tuning support for eMMC HS400
- Add error handling of add_disk()
MMC host:
- mtk-sd: Add host specific tuning support for eMMC HS400
- mtk-sd: Make DMA handling more robust
- dw_mmc: Prevent hangs for some data writes
- dw_mmc: Move away from using the ->init_card() callback
- mxs-mmc: Manage the regulator in the error path and in ->remove()
- sdhci-cadence: Add support for the Microchip MPFS variant
- sdhci-esdhc-imx: Add support for the NXP S32G2 variant
- sdhci-of-arasan: Add support for the Intel Thunder Bay variant
- sdhci-omap: Prepare to support more SoCs
- sdhci-omap: Add support for omap3 and omap4 variants
- sdhci-omap: Add support for power management
- sdhci-omap: Add support for system wakeups
- sdhci-msm: Add support for the msm8226 variant
- sdhci-sprd: Verify that the DLL locks according to spec
MEMSTICK:
- Add error handling of add_disk()
- A couple of small fixes and improvements
-----BEGIN PGP SIGNATURE-----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=W+gH
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Update maintainer and URL for the mmc-utils
- Set default label for slot-gpio in case of no con-id
- Convert MMC card DT bindings to a schema
- Add optional host specific tuning support for eMMC HS400
- Add error handling of add_disk()
MMC host:
- mtk-sd: Add host specific tuning support for eMMC HS400
- mtk-sd: Make DMA handling more robust
- dw_mmc: Prevent hangs for some data writes
- dw_mmc: Move away from using the ->init_card() callback
- mxs-mmc: Manage the regulator in the error path and in ->remove()
- sdhci-cadence: Add support for the Microchip MPFS variant
- sdhci-esdhc-imx: Add support for the NXP S32G2 variant
- sdhci-of-arasan: Add support for the Intel Thunder Bay variant
- sdhci-omap: Prepare to support more SoCs
- sdhci-omap: Add support for omap3 and omap4 variants
- sdhci-omap: Add support for power management
- sdhci-omap: Add support for system wakeups
- sdhci-msm: Add support for the msm8226 variant
- sdhci-sprd: Verify that the DLL locks according to spec
MEMSTICK:
- Add error handling of add_disk()
- A couple of small fixes and improvements"
* tag 'mmc-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (60 commits)
docs: mmc: update maintainer name and URL
mmc: dw_mmc: exynos: Fix spelling mistake "candiates" -> candidates
MAINTAINERS: drop obsolete file pattern in SDHCI DRIVER section
mmc: sdhci-esdhc-imx: add NXP S32G2 support
dt-bindings: mmc: fsl-imx-esdhc: add NXP S32G2 support
mmc: dw_mmc: Drop use of ->init_card() callback
mmc: sdhci-omap: Fix build if CONFIG_PM_SLEEP is not set
mmc: sdhci-omap: Remove forward declaration of sdhci_omap_context_save()
memstick: r592: Fix a UAF bug when removing the driver
mmc: mxs-mmc: disable regulator on error and in the remove function
mmc: sdhci-omap: Configure optional wakeirq
mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM
mmc: sdhci-omap: Implement PM runtime functions
mmc: sdhci-omap: Add omap_offset to support omap3 and earlier
mmc: sdhci-omap: Handle voltages to add support omap4
dt-bindings: sdhci-omap: Update binding for legacy SoCs
mmc: sdhci-pci: Remove dead code (rst_n_gpio et al)
mmc: sdhci-pci: Remove dead code (cd_gpio, cd_irq et al)
mmc: sdhci-pci: Remove dead code (struct sdhci_pci_data et al)
mmc: sdhci: Remove unused prototype declaration in the header
...
These are now pointless wrappers around blk_mq_{alloc,free}_request,
so remove them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20211025070517.1548584-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_keyslot_manager is misnamed because it doesn't necessarily manage
keyslots. It actually does several different things:
- Contains the crypto capabilities of the device.
- Provides functions to control the inline encryption hardware.
Originally these were just for programming/evicting keyslots;
however, new functionality (hardware-wrapped keys) will require new
functions here which are unrelated to keyslots. Moreover,
device-mapper devices already (ab)use "keyslot_evict" to pass key
eviction requests to their underlying devices even though
device-mapper devices don't have any keyslots themselves (so it
really should be "evict_key", not "keyslot_evict").
- Sometimes (but not always!) it manages keyslots. Originally it
always did, but device-mapper devices don't have keyslots
themselves, so they use a "passthrough keyslot manager" which
doesn't actually manage keyslots. This hack works, but the
terminology is unnatural. Also, some hardware doesn't have keyslots
and thus also uses a "passthrough keyslot manager" (support for such
hardware is yet to be upstreamed, but it will happen eventually).
Let's stop having keyslot managers which don't actually manage keyslots.
Instead, rename blk_keyslot_manager to blk_crypto_profile.
This is a fairly big change, since for consistency it also has to update
keyslot manager-related function names, variable names, and comments --
not just the actual struct name. However it's still a fairly
straightforward change, as it doesn't change any actual functionality.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20211018180453.40441-4-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct request is only used by blk-mq drivers, so move it and all
related declarations to blk-mq.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-18-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently default label of GPIO is assigned to the device name,
when no con_id provided. Instead, let's update it to reflect
what it's about (use already prepared template).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210929111757.52625-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor mmc_gpio_alloc() to drop unneeded indentation level
and double condition. This increases readability of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210929111757.52625-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds a ->execute_hs400_tuning() host callback to enable optional
support for host specific tuning for eMMC HS400 mode. Additionally, share
mmc_get_ext_csd() through the public host headerfile, to allow it to be
used by the host drivers, which is needed to support the HS400 tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-3-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We never checked for errors on add_disk() as this function returned void.
Now that this is fixed, use the shiny new error handling.
The caller only cleanups the disk if we pass on an allocated md but on
error we return return ERR_PTR(ret), and so we must do all the unwinding
ourselves.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210830212538.148729-5-mcgrof@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more cleanups
on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9/lg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZNwCggKViEViSGqJFIafAZZjmI3Nt6tUAoMkRlhcd
n1MS3snS0Sq+7BdJs37M
=GyxP
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did the
following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
The latter one will cause a tiny merge issue with your tree, as there
was a last-minute fix for this in 5.14 in your tree, but the fixup
should be "obvious". If you want me to provide a fixed merge for this,
please let me know.
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs
users at once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
s8VFP1NY2BjmxJbkebLL
=8kVu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
- Return a proper response in case of an ioctl error
- Issue HPI to interrupt BKOPS for eMMC if it timed out
- Avoid hogging the CPU while polling for busy
- Extend sd8787 pwrseq to support the wilc1000 SDIO
- Remove a couple of confusing warning messages
- Clarify comment for ->card_busy() host ops
MMC host:
- dw_mmc: Add data CRC error injection
- mmci: De-assert reset during ->probe()
- rtsx_pci: Fix long reads when clock is pre-scaled
- sdhci: Correct the tuning command handle for PIO mode
- sdhci-esdhc-imx: Improve support for auto tuning
- sdhci-msm: Add support for the sc7280
- sdhci-of-arasan: Don't auto tune for DDR50 mode for ZynqMP
- sdhci-of-arasan: Enable support for auto cmd12
- sdhci-of-arasan: Use 19MHz for SD default speed for ZynqMP for level shifter
- usdhi6rol0: Implement the ->card_busy() host ops
MEMSTICK:
- A couple of minor cleanups.
-----BEGIN PGP SIGNATURE-----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=RXpg
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Return a proper response in case of an ioctl error
- Issue HPI to interrupt BKOPS for eMMC if it timed out
- Avoid hogging the CPU while polling for busy
- Extend sd8787 pwrseq to support the wilc1000 SDIO
- Remove a couple of confusing warning messages
- Clarify comment for ->card_busy() host ops
MMC host:
- dw_mmc: Add data CRC error injection
- mmci: De-assert reset during ->probe()
- rtsx_pci: Fix long reads when clock is pre-scaled
- sdhci: Correct the tuning command handle for PIO mode
- sdhci-esdhc-imx: Improve support for auto tuning
- sdhci-msm: Add support for the sc7280
- sdhci-of-arasan: Don't auto tune for DDR50 mode for ZynqMP
- sdhci-of-arasan: Enable support for auto cmd12
- sdhci-of-arasan: Use 19MHz for SD default speed for ZynqMP for level shifter
- usdhi6rol0: Implement the ->card_busy() host ops
MEMSTICK:
- A couple of minor cleanups"
* tag 'mmc-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: queue: Remove unused parameters(request_queue)
mmc: pwrseq: sd8787: fix compilation warning
mmc: core: Return correct emmc response in case of ioctl error
mmc: sdhci-esdhc-imx: Select the correct mode for auto tuning
mmc: sdhci-esdhc-imx: Remove redundant code for manual tuning
mmc: core: Issue HPI in case the BKOPS timed out
mmc: queue: Match the data type of max_segments
mmc: switch from 'pci_' to 'dma_' API
memstick: switch from 'pci_' to 'dma_' API
memstick: r592: Change the name of the 'pci_driver' structure to be consistent
mmc: pwrseq: add wilc1000_sdio dependency for pwrseq_sd8787
mmc: pwrseq: sd8787: add support for wilc1000
dt-bindings: mmc: Extend pwrseq-sd8787 binding for wilc1000
dt-bindings: mmc: fsl-imx-esdhc: change the pinctrl-names rule
dt-bindings: mmc: fsl-imx-esdhc: add a new compatible string
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L bindings
dt-bindings: mmc: renesas,sdhi: Fix dtbs-check warning
mmc: core: Update ->card_busy() callback comment
mmc: usdhi6rol0: Implement card_busy function
mmc: sdhci: Correct the tuning command handle for PIO mode
...
In function mmc_exit_request, the request_queue structure(*q) is not used.
I remove the unnecessary code related to the request_queue structure.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210825074601.8881-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixed compilation warning "cast from pointer to integer of
different size [-Wpointer-to-int-cast]"
Fixes: b2832b96fc ("mmc: pwrseq: sd8787: add support for wilc1000")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210825081931.598934-1-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.
IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)
The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).
It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.
Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().
The test code and the output of only the CMD17 is included in the
commit to limit the message length.
CMD17 (Test Code Snippet):
==========================
printf("Forming CMD%d\n", opt_idx);
/* single block read */
cmd.blksz = 512;
cmd.blocks = 1;
cmd.write_flag = 0;
cmd.opcode = 17;
//cmd.arg = atoi(argv[3]);
cmd.arg = 0x09B2FFFF;
/* Expecting response R1B */
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
memset(data, 0, sizeof(__u8) * 512);
mmc_ioc_cmd_set_data(cmd, data);
printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
if(ioctl(fd, MMC_IOC_CMD, &cmd))
perror("Error");
printf("\nResponse: %08x\n", cmd.response[0]);
CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 00000000
(Incorrect response)
CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support generic alternative_gpt_sector() block device operation.
It calculates location of GPT entry for eMMC of NVIDIA Tegra Android
devices. Add new MMC_CAP2_ALT_GPT_TEGRA flag that enables scanning of
alternative GPT sector and add raw_boot_mult field to mmc_ext_csd
which allows to get size of the boot partitions that is needed for
the calculation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210820004536.15791-4-digetx@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the BKOPS timed out, the card is probably still busy in the
R1_STATE_PRG. Rather than continue as nothing has happened and hitting and
error for the next command being sent, let's try to abort the running BKOPS
by sending a HPI command to get back into R1_STATE_TRAN.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210817224208.153652-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Each function has a different data type for max_segments,
Modify to match unsigned short(host->max_segs).
* unsigned short max_segs; /* see blk_queue_max_segments */
1) Return type : unsigned int
static unsigned int mmc_get_max_segments(struct mmc_host *host)
{
return host->can_dma_map_merge ? MMC_DMA_MAP_MERGE_SEGMENTS :
host->max_segs;
}
2) Parameter type : int
mmc_alloc_sg(mmc_get_max_segments(host), gfp);
-> static struct scatterlist *mmc_alloc_sg(int sg_len, gfp_t gfp)
3) Parameter type : unsigned short
blk_queue_max_segments(mq->queue, mmc_get_max_segments(host));
-> void blk_queue_max_segments(struct request_queue *q,
unsigned short max_segments)
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20210824073934.19727-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add new compatible for wilc1000 devices and specify the delay in .data
member of struct of_device_id. WILC1000, WILC3000 devices needs a minimum
of 5ms delay b/w reset and power lines.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210820092803.78523-3-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Print out the contents of the offending tuples when we do print them.
This can make it easier to debug, since these tuples are not exposed to
userspace anywhere else. We are limited to 64 bytes, so keep printing
out the full length in case the tuple is truncated.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-2-sean.anderson@seco.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CIS tuples in the range 0x80-0x8F are reserved for vendors. Some devices
have tuples in this range which get warned about every boot. Since this
is normal behavior, don't print these tuples unless debug is enabled.
Unfortunately, we cannot use a variable for the format string since it
gets pasted by pr_*_ratelimited.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-1-sean.anderson@seco.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Skip printing a retune error when we scan for a removed card because we
then expect a failed command.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210630041658.7574-1-wsa+renesas@sang-engineering.com
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make 'struct mmc_request' contain a pointer to the request's
'struct bio_crypt_ctx' directly, instead of extracting a 32-bit DUN from
it which is a cqhci-crypto specific detail.
This keeps the cqhci crypto specific details in the cqhci module, and it
makes mmc_core and mmc_block ready for MMC crypto hardware that accepts
the DUN and/or key in a way that is more flexible than that which will
be specified by the eMMC v5.2 standard. Exynos SoCs are an example of
such hardware, as their inline encryption hardware takes keys directly
(it has no concept of keyslots) and supports 128-bit DUNs.
Note that the 32-bit DUN length specified by the standard is very
restrictive, so it is likely that more hardware will support longer DUNs
despite it not following the standard. Thus, limiting the scope of the
32-bit DUN assumption to the place that actually needs it is warranted.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210721154738.3966463-1-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc_blk_card_busy() calls card_busy_detect() to poll for the card's
state with CMD13, this is done without any delays in between the commands
being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common __mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-4-ulf.hansson@linaro.org
When __mmc_blk_ioctl_cmd() calls card_busy_detect() to verify that the
card's states moves back into transfer state, the polling with CMD13 is
done without any delays in between the commands being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-3-ulf.hansson@linaro.org
When mmc_blk_fix_state() sends a CMD12 to try to move the card into the
transfer state, it calls card_busy_detect() to poll for the card's state
with CMD13. This is done without any delays in between the commands being
sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-2-ulf.hansson@linaro.org
We have this in two places, so let's have a dedicated function. It is
also more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624151616.38770-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I wanted to use it in a wrong way, so document the intended way.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624151616.38770-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Restructure mmc_blk_probe to avoid a failure path with a half created
disk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210809064028.1198327-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the attribute group for the attributes on the gendisk to
device_add_disk so that they are created atomically with the
disk creation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210809064028.1198327-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68e (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a chance that the IDA allocated in mmc_alloc_host() is not freed
for some time because it's freed as part of a class' release function
(see mmc_host_classdev_release() where the IDA is freed). If another
thread is holding a reference to the class, then only once all balancing
device_put() calls (in turn calling kobject_put()) have been made will
the IDA be released and usable again.
Normally this isn't a problem because the kobject is released before
anything else that may want to use the same number tries to again, but
with CONFIG_DEBUG_KOBJECT_RELEASE=y and OF aliases it becomes pretty
easy to try to allocate an alias from the IDA twice while the first time
it was allocated is still pending a call to ida_simple_remove(). It's
also possible to trigger it by using CONFIG_DEBUG_KOBJECT_RELEASE and
probe defering a driver at boot that calls mmc_alloc_host() before
trying to get resources that may defer likes clks or regulators.
Instead of allocating from the IDA in this scenario, let's just skip it
if we know this is an OF alias. The number is already "claimed" and
devices that aren't using OF aliases won't try to use the claimed
numbers anyway (see mmc_first_nonreserved_index()). This should avoid
any issues with mmc_alloc_host() returning failures from the
ida_simple_get() in the case that we're using an OF alias.
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Sujit Kautkar <sujitka@chromium.org>
Reported-by: Zubin Mithra <zsm@chromium.org>
Fixes: fa2d0aa969 ("mmc: core: Allow setting slot index via device tree alias")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210623075002.1746924-3-swboyd@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf reported the following KASAN splat after adding some manual hacks
into mmc-utils[1].
DEBUG: mmc_blk_open: Let's sleep for 10s..
mmc1: card 0007 removed
BUG: KASAN: use-after-free in mmc_blk_get+0x58/0xb8
Read of size 4 at addr ffff00000a394a28 by task mmc/180
CPU: 2 PID: 180 Comm: mmc Not tainted 5.10.0-rc4-00069-gcc758c8c7127-dirty #5
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
Call trace:
dump_backtrace+0x0/0x2b4
show_stack+0x18/0x6c
dump_stack+0xfc/0x168
print_address_description.constprop.0+0x6c/0x488
kasan_report+0x118/0x210
__asan_load4+0x94/0xd0
mmc_blk_get+0x58/0xb8
mmc_blk_open+0x7c/0xdc
__blkdev_get+0x3b4/0x964
blkdev_get+0x64/0x100
blkdev_open+0xe8/0x104
do_dentry_open+0x234/0x61c
vfs_open+0x54/0x64
path_openat+0xe04/0x1584
do_filp_open+0xe8/0x1e4
do_sys_openat2+0x120/0x230
__arm64_sys_openat+0xf0/0x15c
el0_svc_common.constprop.0+0xac/0x234
do_el0_svc+0x84/0xa0
el0_sync_handler+0x264/0x270
el0_sync+0x174/0x180
Allocated by task 33:
stack_trace_save+0x9c/0xdc
kasan_save_stack+0x28/0x60
__kasan_kmalloc.constprop.0+0xc8/0xf0
kasan_kmalloc+0x10/0x20
mmc_blk_alloc_req+0x94/0x4b0
mmc_blk_probe+0x2d4/0xaa4
mmc_bus_probe+0x34/0x4c
really_probe+0x148/0x6e0
driver_probe_device+0x78/0xec
__device_attach_driver+0x108/0x16c
bus_for_each_drv+0xf4/0x15c
__device_attach+0x168/0x240
device_initial_probe+0x14/0x20
bus_probe_device+0xec/0x100
device_add+0x55c/0xaf0
mmc_add_card+0x288/0x380
mmc_attach_sd+0x18c/0x22c
mmc_rescan+0x444/0x4f0
process_one_work+0x3b8/0x650
worker_thread+0xa0/0x724
kthread+0x218/0x220
ret_from_fork+0x10/0x38
Freed by task 33:
stack_trace_save+0x9c/0xdc
kasan_save_stack+0x28/0x60
kasan_set_track+0x28/0x40
kasan_set_free_info+0x24/0x4c
__kasan_slab_free+0x100/0x180
kasan_slab_free+0x14/0x20
kfree+0xb8/0x46c
mmc_blk_put+0xe4/0x11c
mmc_blk_remove_req.part.0+0x6c/0xe4
mmc_blk_remove+0x368/0x370
mmc_bus_remove+0x34/0x50
__device_release_driver+0x228/0x31c
device_release_driver+0x2c/0x44
bus_remove_device+0x1e4/0x200
device_del+0x2b0/0x770
mmc_remove_card+0xf0/0x150
mmc_sd_detect+0x9c/0x150
mmc_rescan+0x110/0x4f0
process_one_work+0x3b8/0x650
worker_thread+0xa0/0x724
kthread+0x218/0x220
ret_from_fork+0x10/0x38
The buggy address belongs to the object at ffff00000a394800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 552 bytes inside of
1024-byte region [ffff00000a394800, ffff00000a394c00)
The buggy address belongs to the page:
page:00000000ff84ed53 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x8a390
head:00000000ff84ed53 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x3fffc0000010200(slab|head)
raw: 03fffc0000010200 dead000000000100 dead000000000122 ffff000009f03800
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff00000a394900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff00000a394980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff00000a394a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff00000a394a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff00000a394b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Looking closer at the problem, it looks like a classic dangling pointer
bug. The 'struct mmc_blk_data' that is used after being freed in
mmc_blk_put() is stashed away in 'md->disk->private_data' via
mmc_blk_alloc_req() but used in mmc_blk_get() because the 'usage' count
isn't properly aligned with the lifetime of the pointer. You'd expect
the 'usage' member to be in sync with the kfree(), and it mostly is,
except that mmc_blk_get() needs to dereference the potentially freed
memory storage for the 'struct mmc_blk_data' stashed away in the
private_data member to look at 'usage' before it actually figures out if
it wants to consider it a valid pointer or not. That's not going to work
if the freed memory has been overwritten by something else after the
free, and KASAN rightly complains here.
To fix the immediate problem, let's set the private_data member to NULL
in mmc_blk_put() so that mmc_blk_get() can consider the object "on the
way out" if the pointer is NULL and not even try to look at 'usage' if
the object isn't going to be around much longer. With that set to NULL
on the last mmc_blk_put(), optimize the get path further and use a kref
underneath the 'open_lock' mutex to only up the reference count if it's
non-zero, i.e. alive, and otherwise make mmc_blk_get() return NULL,
without actually testing the reference count if we're in the process of
removing the object from the system.
Finally, tighten the locking region on the put side to only be around
the parts that are removing the 'mmc_blk_data' from the system and
publishing that fact to the gendisk and then drop the lock as soon as we
can to avoid holding the lock around code that doesn't need it. This
fixes the KASAN issue.
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Sujit Kautkar <sujitka@chromium.org>
Cc: Zubin Mithra <zsm@chromium.org>
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/linux-mmc/CAPDyKFryT63Jc7+DXWSpAC19qpZRqFr1orxwYGMuSqx247O8cQ@mail.gmail.com/ [1]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210623075002.1746924-2-swboyd@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=gHse
-----END PGP SIGNATURE-----
Merge tag 'block-5.14-2021-07-08' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
"A combination of changes that ended up depending on both the driver
and core branch (and/or the IDE removal), and a few late arriving
fixes. In detail:
- Fix io ticks wrap-around issue (Chunguang)
- nvme-tcp sock locking fix (Maurizio)
- s390-dasd fixes (Kees, Christoph)
- blk_execute_rq polling support (Keith)
- blk-cgroup RCU iteration fix (Yu)
- nbd backend ID addition (Prasanna)
- Partition deletion fix (Yufen)
- Use blk_mq_alloc_disk for mmc, mtip32xx, ubd (Christoph)
- Removal of now dead block request types due to IDE removal
(Christoph)
- Loop probing and control device cleanups (Christoph)
- Device uevent fix (Christoph)
- Misc cleanups/fixes (Tetsuo, Christoph)"
* tag 'block-5.14-2021-07-08' of git://git.kernel.dk/linux-block: (34 commits)
blk-cgroup: prevent rcu_sched detected stalls warnings while iterating blkgs
block: fix the problem of io_ticks becoming smaller
nvme-tcp: can't set sk_user_data without write_lock
loop: remove unused variable in loop_set_status()
block: remove the bdgrab in blk_drop_partitions
block: grab a device refcount in disk_uevent
s390/dasd: Avoid field over-reading memcpy()
dasd: unexport dasd_set_target_state
block: check disk exist before trying to add partition
ubd: remove dead code in ubd_setup_common
nvme: use return value from blk_execute_rq()
block: return errors from blk_execute_rq()
nvme: use blk_execute_rq() for passthrough commands
block: support polling through blk_execute_rq
block: remove REQ_OP_SCSI_{IN,OUT}
block: mark blk_mq_init_queue_data static
loop: rewrite loop_exit using idr_for_each_entry
loop: split loop_lookup
loop: don't allow deleting an unspecified loop device
loop: move loop_ctl_mutex locking into loop_add
...
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Fix a let hunk from the blk_mq_alloc_disk conversion.
Fixes: 281ea6a5bfdc ("mmc: switch to blk_mq_alloc_disk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210621080144.3655131-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the blk_mq_alloc_disk to allocate the request_queue and gendisk
together.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210616053934.880951-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The gendisk already acquires a reference to the queue when add_disk
is called, which dropped on put_disk. So remove the superflous
extra refcounting.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210616053934.880951-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It might be that something goes wrong during tuning so the MMC core will
immediately trigger a retune. In our case it was:
- we sent a tuning block
- there was an error so we need to send an abort cmd to the eMMC
- the abort cmd had a CRC error
- retune was set by the MMC core
This lead to a vicious circle causing a performance regression of 75%.
So, clear retuning flags before we enable retuning to start with a known
cleared state.
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'mmc_abort_tuning()' made me think tuning gets completely aborted.
However, it sends only a STOP cmd to cancel the current tuning cmd.
Tuning process may still continue after that. So, rename the function to
'mmc_send_abort_tuning()' to better reflect all this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210608180620.40059-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While initializing an UHS-I SD card, the mmc core first tries to switch to
1.8V I/O voltage, before it continues to change the settings for the bus
speed mode.
However, the current behaviour in the mmc core is inconsistent and doesn't
conform to the SD spec. More precisely, an SD card that supports UHS-I must
set both the SD_OCR_CCS bit and the SD_OCR_S18R bit in the OCR register
response. When switching to 1.8V I/O the mmc core correctly checks both of
the bits, but only the SD_OCR_S18R bit when changing the settings for bus
speed mode.
Rather than actually fixing the code to confirm to the SD spec, let's
deliberately deviate from it by requiring only the SD_OCR_S18R bit for both
parts. This enables us to support UHS-I for SDSC cards (outside spec),
which is actually being supported by some existing SDSC cards. Moreover,
this fixes the inconsistent behaviour.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Link: https://lore.kernel.org/r/CWXP265MB26803AE79E0AD5ED083BF2A6C4529@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM
Cc: stable@vger.kernel.org
[Ulf: Rewrote commit message and comments to clarify the changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621513304-27824-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some boards the data strobe line isn't wired up, rendering HS400
support broken, even if both the controller and the eMMC claim to
support it. Allow to disable HS400 mode via DT.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Link: https://lore.kernel.org/r/20210510190400.105162-3-l.stach@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In SD spec v6.x the SD function extension registers for performance
enhancements were introduced. As a part of this an optional internal cache
on the SD card, can be used to improve performance.
The let the SD card use the cache, the host needs to enable it and manage
flushing of the cache, so let's add support for this.
Note that for an SD card supporting the cache it's mandatory for it, to
also support the poweroff notification feature. According to the SD spec,
if the cache has been enabled and a poweroff notification is sent to the
card, that implicitly also means that the card should flush its internal
cache. Therefore, dealing with cache flushing for REQ_OP_FLUSH block
requests is sufficient.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210511101359.83521-1-ulf.hansson@linaro.org
To prepare to add internal cache management for SD cards, let's start by
moving the eMMC specific code into a new ->flush_cache() bus_ops callback.
In this way, it becomes straight forward to add the SD specific parts,
as subsequent changes are about to show.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210506145829.198823-2-ulf.hansson@linaro.org
According to the eMMC Spec:
"When command queuing is enabled (CMDQ Mode En bit in CMDQ_MODE_EN
field is set to ‘1’) class 11 commands are the only method through
which data transfer tasks can be issued. Existing data transfer
commands, namely CMD18/CMD17 and CMD25/CMD24, are not supported when
command queuing is enabled."
which means if CMDQ is enabled, the FFU commands will not be supported.
To fix this issue, just simply disable CMDQ on the ioctl path, and
re-enable CMDQ once ioctl request is completed.
Tested-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 1e8e55b670 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210504203209.361597-1-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rather than only deselecting the SD card via a CMD7, before we cut power to
it at system suspend, at runtime suspend or at shutdown, let's add support
for a graceful power off sequence via enabling the SD Power Off
Notification feature.
Note that, the Power Off Notification feature was added in the SD spec
v4.x, which is several years ago. However, it's still a bit unclear how
often the SD card vendors decides to implement support for it. To validate
these changes a Sandisk Extreme PRO A2 64GB has been used, which seems to
work nicely.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210504161222.101536-12-ulf.hansson@linaro.org
In SD spec v6.x the SD function extension registers for performance
enhancements were introduced. These registers let the SD card announce
supports for various performance related features, like "self-maintenance",
"cache" and "command queuing".
Let's extend the parsing of SD function extension registers and store the
information in the struct mmc_card. This prepares for subsequent changes to
implement the complete support for new the performance enhancement
features.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210504161222.101536-11-ulf.hansson@linaro.org
In the SD spec v4.0 the CMD48/49 and CMD58/59 were introduced as optional
commands. In the SD spec v4.1 the SD function extension registers were
introduced, which requires support for CMD48/49/58/59 to be read/written
from/to.
Moreover, a specific function extension register were added to let the card
announce support for optional features in regards to power management. The
features that were added are "Power Off Notification", "Power Down Mode"
and "Power Sustenance".
As a first step to support this, let's read and parse the register for
power management during the SD card initialization and store the
information about the supported features in the struct mmc_card. In this
way, we prepare for subsequent changes to implement the complete support
for the new features.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-10-ulf.hansson@linaro.org
In SD spec v4.x the support for CMD48/49 and CMD58/59 were introduced as
optional features. To let the card announce whether it supports the
commands, the SCR register has been extended with corresponding support
bits. Let's parse and store this information for later use.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-9-ulf.hansson@linaro.org
The SD_SWITCH (CMD6) is an ADTC type of command with an R1 response, which
can be sent by using the mmc_send_adtc_data(). Let's do that and drop the
open coding in mmc_sd_switch().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-8-ulf.hansson@linaro.org
The function mmc_send_cxd_data() sends a data read command of ADTC type and
prepares to receive an R1 response. To make it even more re-usable, let's
extend it with another in-parameter for the command argument. While at it,
let's also rename the function to mmc_send_adtc_data() as it better
describes its purpose.
Note that, this change doesn't add any new users of the function. Instead
that is done from subsequent changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-7-ulf.hansson@linaro.org
After the eMMC sleep command (CMD5) has been sent, the card start signals
busy on the DAT0 line, which can be monitored to understand when it's
allowed to proceed to power off the VCC regulator.
When MMC_CAP_WAIT_WHILE_BUSY isn't supported by the host the DAT0 line
isn't being monitored for busy completion, but instead we are waiting a
fixed period of time. The time corresponds to the sleep timeout that is
specified in the EXT_CSD register of the eMMC card. This is many cases
suboptimal, as the timeout corresponds to the worst case scenario.
To improve the situation add support for HW busy polling through the
->card_busy() host ops, when the host supports this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-6-ulf.hansson@linaro.org
Via __mmc_poll_for_busy() we end up polling with the ->card_busy() host ops
or by sending the CMD13. To allow polling of different types, which is
needed to support a few new SD card features, let's rework the code around
__mmc_poll_for_busy() to make it more generic.
More precisely, let __mmc_poll_for_busy() take a pointer to a callback
function as in-parameter, which it calls to poll for busy state completion.
Additionally, let's share __mmc_poll_for_busy() to allow it to be re-used
outside of mmc_ops.c. Subsequent changes will make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-5-ulf.hansson@linaro.org
To make the code a bit more understandable, let's move the check about
whether polling is allowed or not, out to the caller instead. In this way,
we can also drop the send_status in-parameter, so let's do that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-4-ulf.hansson@linaro.org
In mmc_send_hpi_cmd() the host->max_busy_timeout is being validated towards
the timeout for the eMMC HPI command, as to decide whether an R1 or R1B
response should be used.
Although, it has turned out the some host can't cope with that conversion,
but needs R1B, which means MMC_CAP_NEED_RSP_BUSY is set for them. Let's
take this into account, via using the common mmc_prepare_busy_cmd() when
doing the validation, which also avoids some open coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-3-ulf.hansson@linaro.org
Similar code for validating the host->max_busy_timeout towards the current
command's busy timeout, exists in mmc_do_erase(), mmc_sleep() and
__mmc_switch(). Let's move the common code into a helper function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-2-ulf.hansson@linaro.org
tty_operations::chars_in_buffer is another hook which is expected to
return values >= 0. So make it explicit by the return type too -- use
unsigned int.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: David Sterba <dsterba@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Group the flow flags under a single struct called flow. The new struct
contains 'stopped' and 'tco_stopped' bools which used to be bits in a
bitfield. The struct also contains the lock protecting them to
potentially share the same cache line.
Note that commit c545b66c69 (tty: Serialize tcflow() with other tty
flow control changes) added a padding to the original bitfield. It was
for the bitfield to occupy a whole 64b word to avoid interferring stores
on Alpha (cannot we evaporate this arch with weird implications to C
code yet?). But it doesn't work as expected as the padding
(tty_struct::unused) is aligned to a 8B boundary too and occupies some
bytes from the next word.
So make it reliable by:
1) setting __aligned of the struct -- that aligns the start, and
2) making 'unsigned long unused[0]' as the last member of the struct --
pads the end.
This is also the perfect time to start the documentation of tty_struct
where all this lives. So we start by documenting what these bools
actually serve for. And why we do all the alignment dances. Only the few
up-to-date information from the Theodore's comment made it into this new
Kerneldoc comment.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/20210505091928.22010-13-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In command queueing mode, the cache isn't flushed via the mmc_flush_cache()
function, but instead by issuing a CMDQ_TASK_MGMT (CMD48) with a
FLUSH_CACHE opcode. In this path, we need to check if cache has been
enabled, before deciding to flush the cache, along the lines of what's
being done in mmc_flush_cache().
To fix this problem, let's add a new bus ops callback ->cache_enabled() and
implement it for the mmc bus type. In this way, the mmc block device driver
can call it to know whether cache flushing should be done.
Fixes: 1e8e55b670 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Reported-by: Brendan Peter <bpeter@lytx.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Tested-by: Brendan Peter <bpeter@lytx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210425060207.2591-2-avri.altman@wdc.com
Link: https://lore.kernel.org/r/20210425060207.2591-3-avri.altman@wdc.com
[Ulf: Squashed the two patches and made some minor updates]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The cache function can be turned ON and OFF by writing to the CACHE_CTRL
byte (EXT_CSD byte [33]). However, card->ext_csd.cache_ctrl is only
set on init if cache size > 0.
Fix that by explicitly setting ext_csd.cache_ctrl on ext-csd write.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210420134641.57343-3-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_of_parse() for a few years has been using device property API.
Convert mmc_of_parse_voltage() as well.
At the same time switch users to new API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since it has been converted to use device property API, the function
and field descriptions become outdated. Correct them.
Fixes: 73a47a9bb3 ("mmc: core: Use device_property_read instead of of_property_read")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all commands need to be retried in case of a timeout/failure. This is
the case for the eMMC sanitize command, for example, which is issued
through the ioctl interface. More precisely, in case of timeout, retrying
could make the user wait for a very long time as each retry loop could last
for a couple of minutes.
Therefore, let's not use retries for the eMMC sanitize command.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210414212236.346813-3-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add command retries parameter to __mmc_switch(), let caller
pass retries according to the caller's condition.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210414212236.346813-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the density increases, the 4-minute timeout value for sanitize is no
longer feasible. At the same time, devices of different densities have
different timeout values, which makes it difficult to use a common timeout
value. Therefore, let's pass down the userland-specified sanitize timeout
value so it can be used.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210402092432.25069-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc core uses a PM notifier to temporarily during system suspend, turn
off the card detection mechanism for removal/insertion of (e)MMC/SD/SDIO
cards. Additionally, the notifier may be used to remove an SDIO card
entirely, if a corresponding SDIO functional driver don't have the system
suspend/resume callbacks assigned. This behaviour has been around for a
very long time.
However, a recent bug report tells us there are problems with this
approach. More precisely, when receiving the PM_SUSPEND_PREPARE
notification, we may end up hanging on I/O to be completed, thus also
preventing the system from getting suspended.
In the end what happens, is that the cancel_delayed_work_sync() in
mmc_pm_notify() ends up waiting for mmc_rescan() to complete - and since
mmc_rescan() wants to claim the host, it needs to wait for the I/O to be
completed first.
Typically, this problem is triggered in Android, if there is ongoing I/O
while the user decides to suspend, resume and then suspend the system
again. This due to that after the resume, an mmc_rescan() work gets punted
to the workqueue, which job is to verify that the card remains inserted
after the system has resumed.
To fix this problem, userspace needs to become frozen to suspend the I/O,
prior to turning off the card detection mechanism. Therefore, let's drop
the PM notifiers for mmc subsystem altogether and rely on the card
detection to be turned off/on as a part of the system_freezable_wq, that we
are already using.
Moreover, to allow and SDIO card to be removed during system suspend, let's
manage this from a ->prepare() callback, assigned at the mmc_host_class
level. In this way, we can use the parent device (the mmc_host_class
device), to remove the card device that is the child, in the
device_prepare() phase.
Reported-by: Kiwoong Kim <kwmad.kim@samsung.com>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210310152900.149380-1-ulf.hansson@linaro.org
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
The host->cqe_enabled is already containing the needed information about
whether the CQE is enabled or not, hence there is no need to keep another
copy of it around.
Signed-off-by: Luca Porzio <lporzio@micron.com>
Signed-off-by: Zhan Liu <zliua@micron.com>
Link: https://lore.kernel.org/r/20210215003217.GA12240@lupo-laptop
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Returning zero to indicate success, when we actually have failed to probe
is wrong. As a matter of fact, it leads to that mmc_blk_remove() gets
called at a card removal and then triggers "NULL pointer dereference"
splats. This is because mmc_blk_remove() relies on data structures and
pointers to be setup from mmc_blk_probe(), of course.
There have been no errors reported about this, which is most likely because
mmc_blk_probe() never fails like this. Nevertheless, let's fix the code by
propagating the error codes correctly and prevent us from leaking memory by
calling also destroy_workqueue() in the error path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210303122049.151986-4-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify the code, move the logging into the common mmc_blk_alloc_req()
and drop the rather useless information about the partition type/id.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210303122049.151986-3-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_probe() isn't a hotpath, which makes it's questionable to use
unlikely(). Therefore let's simply drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210303122049.151986-2-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of SD cards sets permanent write protection bit in their CSD register,
due to lifespan or internal problem. To avoid unnecessary I/O write
operations, let's parse the bits in the CSD during initialization and mark
the card as read only for this case.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20210222083156.19158-1-sh043.lee@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_spi_send_{csd|cid} have similar function body. Let's remove the
duplicated part to simplify the code, just add opcode to distinguish
them in changed mmc_spi_send_cxd().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210215015116.1355-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the mmc_rescan work is enabled for execution (host->rescan_disable),
it's the only instance per mmc host that is allowed to set/clear the
host->bus_ops pointer.
Besides the mmc_rescan work, there are a couple of scenarios when the
host->bus_ops pointer may be accessed. Typically, those can be described as
as below:
*)
Upper mmc driver layers (like the mmc block device driver or an SDIO
functional driver) needs to execute a host->bus_ops callback. This can be
considered as safe without having to use some special locking mechanism,
because they operate on top of the struct mmc_card. As long as there is a
card to operate upon, the mmc core guarantees that there is a host->bus_ops
assigned as well. Note that, upper layer mmc drivers are of course
responsible to clean up from themselves from their ->remove() callbacks,
otherwise things would fall apart anyways.
**)
Via the mmc host instance, we may need to force a removal of an inserted
mmc card. This happens when a mmc host driver gets unbind, for example. In
this case, we protect the host->bus_ops pointer from concurrent accesses,
by disabling the mmc_rescan work upfront (host->rescan_disable). See
mmc_stop_host() for example.
This said, it seems like the reference counting of the host->bus_ops
pointer at some point have become superfluous. As this is an old mechanism
of the mmc core, it a bit difficult to digest the history of when that
could have happened. However, let's drop the reference counting to avoid
unnecessary code-paths and lockings.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210212131610.236843-1-ulf.hansson@linaro.org
The mmc_hw|sw_reset() APIs are designed to be called solely from upper
layers, which means drivers that operates on top of the struct mmc_card,
like the mmc block device driver and an SDIO functional driver.
Additionally, as long as the struct mmc_host has a valid pointer to a
struct mmc_card, the corresponding host->bus_ops pointer stays valid and
assigned.
For these reasons, let's drop the superfluous reference counting and the
redundant validations in mmc_hw|sw_reset().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210212131532.236775-1-ulf.hansson@linaro.org
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com>
Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Add support for eMMC inline encryption
- Add a helper function to parse DT properties for clock phases
- Some improvements and cleanups for the mmc_test module
MMC host:
- android-goldfish: Remove driver
- cqhci: Add support for eMMC inline encryption
- dw_mmc-zx: Remove driver
- meson-gx: Extend support for scatter-gather to allow SD_IO_RW_EXTENDED
- mmci: Add support for probing bus voltage level translator
- mtk-sd: Address race condition for request timeouts
- sdhci_am654: Add Support for the variant on TI's AM64 SoC
- sdhci-esdhc-imx: Prevent kernel panic at ->remove()
- sdhci-iproc: Add ACPI bindings for the RPi to enable SD and WiFi on RPi4
- sdhci-msm: Add Inline Crypto Engine support
- sdhci-msm: Use actual_clock to improve timeout calculations
- sdhci-of-aspeed: Add Andrew Jeffery as maintainer
- sdhci-of-aspeed: Extend clock support for the AST2600 variant
- sdhci-pci-gli: Increase idle period for low power state for GL9763E
- sdhci-pci-o2micro: Make tuning for SDR104 HW more robust
- sdhci-sirf: Remove driver
- sdhci-xenon: Add support for the AP807 variant
- sunxi-mmc: Add support for the A100 variant
- sunxi-mmc: Ensure host is suspended during system sleep
- tmio: Add detection of data timeout errors
- tmio/renesas_sdhi: Extend support for retuning
- renesas_sdhi_internal_dmac: Add support for the ->pre|post_req() ops
-----BEGIN PGP SIGNATURE-----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=rwB7
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for eMMC inline encryption
- Add a helper function to parse DT properties for clock phases
- Some improvements and cleanups for the mmc_test module
MMC host:
- android-goldfish: Remove driver
- cqhci: Add support for eMMC inline encryption
- dw_mmc-zx: Remove driver
- meson-gx: Extend support for scatter-gather to allow SD_IO_RW_EXTENDED
- mmci: Add support for probing bus voltage level translator
- mtk-sd: Address race condition for request timeouts
- sdhci_am654: Add Support for the variant on TI's AM64 SoC
- sdhci-esdhc-imx: Prevent kernel panic at ->remove()
- sdhci-iproc: Add ACPI bindings for the RPi to enable SD and WiFi on RPi4
- sdhci-msm: Add Inline Crypto Engine support
- sdhci-msm: Use actual_clock to improve timeout calculations
- sdhci-of-aspeed: Add Andrew Jeffery as maintainer
- sdhci-of-aspeed: Extend clock support for the AST2600 variant
- sdhci-pci-gli: Increase idle period for low power state for GL9763E
- sdhci-pci-o2micro: Make tuning for SDR104 HW more robust
- sdhci-sirf: Remove driver
- sdhci-xenon: Add support for the AP807 variant
- sunxi-mmc: Add support for the A100 variant
- sunxi-mmc: Ensure host is suspended during system sleep
- tmio: Add detection of data timeout errors
- tmio/renesas_sdhi: Extend support for retuning
- renesas_sdhi_internal_dmac: Add support for the ->pre|post_req() ops"
* tag 'mmc-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: sdhci-esdhc-imx: fix kernel panic when remove module
mmc: host: Retire MMC_GOLDFISH
mmc: cb710: Use new tasklet API
mmc: sdhci-pci-o2micro: Bug fix for SDR104 HW tuning failure
mmc: mmc_test: use erase_arg for mmc_erase command
mmc: wbsd: Use new tasklet API
mmc: via-sdmmc: Use new tasklet API
mmc: uniphier-sd: Use new tasklet API
mmc: tifm_sd: Use new tasklet API
mmc: s3cmci: Use new tasklet API
mmc: omap: Use new tasklet API
mmc: dw_mmc: Use new tasklet API
mmc: au1xmmc: Use new tasklet API
mmc: atmel-mci: Use new tasklet API
mmc: cavium: Replace spin_lock_irqsave with spin_lock in hard IRQ
mmc: queue: Remove unused define
mmc: core: Drop redundant bouncesz from struct mmc_card
mmc: core: Drop redundant member in struct mmc host
mmc: core: Use host instead of card argument to mmc_spi_send_csd()
mmc: core: Exclude unnecessary header file
...
-----BEGIN PGP SIGNATURE-----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=os1E
-----END PGP SIGNATURE-----
Merge tag 'for-5.12/block-2021-02-17' of git://git.kernel.dk/linux-block
Pull core block updates from Jens Axboe:
"Another nice round of removing more code than what is added, mostly
due to Christoph's relentless pursuit of tech debt removal/cleanups.
This pull request contains:
- Two series of BFQ improvements (Paolo, Jan, Jia)
- Block iov_iter improvements (Pavel)
- bsg error path fix (Pan)
- blk-mq scheduler improvements (Jan)
- -EBUSY discard fix (Jan)
- bvec allocation improvements (Ming, Christoph)
- bio allocation and init improvements (Christoph)
- Store bdev pointer in bio instead of gendisk + partno (Christoph)
- Block trace point cleanups (Christoph)
- hard read-only vs read-only split (Christoph)
- Block based swap cleanups (Christoph)
- Zoned write granularity support (Damien)
- Various fixes/tweaks (Chunguang, Guoqing, Lei, Lukas, Huhai)"
* tag 'for-5.12/block-2021-02-17' of git://git.kernel.dk/linux-block: (104 commits)
mm: simplify swapdev_block
sd_zbc: clear zone resources for non-zoned case
block: introduce blk_queue_clear_zone_settings()
zonefs: use zone write granularity as block size
block: introduce zone_write_granularity limit
block: use blk_queue_set_zoned in add_partition()
nullb: use blk_queue_set_zoned() to setup zoned devices
nvme: cleanup zone information initialization
block: document zone_append_max_bytes attribute
block: use bi_max_vecs to find the bvec pool
md/raid10: remove dead code in reshape_request
block: mark the bio as cloned in bio_iov_bvec_set
block: set BIO_NO_PAGE_REF in bio_iov_bvec_set
block: remove a layer of indentation in bio_iov_iter_get_pages
block: turn the nr_iovecs argument to bio_alloc* into an unsigned short
block: remove the 1 and 4 vec bvec_slabs entries
block: streamline bvec_alloc
block: factor out a bvec_alloc_gfp helper
block: move struct biovec_slab to bio.c
block: reuse BIO_INLINE_VECS for integrity bvecs
...
Since [1], the erase argument for mmc_erase() function is saved in
erase_arg field of card structure. It is preferable to use it instead of
hard-coded MMC_SECURE_ERASE_ARG, which from eMMC 4.51 spec is not
recommended:
"6.6.16 Secure Erase
NOTE Secure Erase is included for backwards compatibility. New system
level implementations (based on v4.51 devices and beyond) should use
Erase combined with Sanitize instead of secure erase."
On STM32MP157C-EV1 board, embedding a THGBMDG5D1LBAIL eMMC, using
MMC_ERASE command with MMC_SECURE_ERASE_ARG may stuck the STM32 SDMMC IP,
if test 37 or test 38 are launched just after a write test, e.g. test 36.
Using the default MMC_ERASE argument from framework with erase_arg,
which default in our case to MMC_DISCARD_ARG does no more trig the
issue.
[1] commit 01904ff776 ("mmc: core: Calculate the discard arg only once")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210209145214.10518-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CQE_QUEUE_FULL is not set and is only cleared.
Therefore, define is unnecessary.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210203072014.30272-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
From the 4.19 kernel, thread related code has been removed in queue.c.
So we can exclude unnecessary header file.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20210125064355.28545-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding CQHCI crypto engine (inline encryption)
support, add the code required to make mmc_core and mmc_block aware of
inline encryption. Specifically:
- Add a capability flag MMC_CAP2_CRYPTO to struct mmc_host. Drivers
will set this if the host and driver support inline encryption.
- Embed a blk_keyslot_manager in struct mmc_host. Drivers will
initialize this (as a device-managed resource) if the host and driver
support inline encryption. mmc_block registers this keyslot manager
with the request_queue of any MMC card attached to the host.
- Make mmc_block copy the crypto keyslot and crypto data unit number
from struct request to struct mmc_request, so that drivers will have
access to them.
- If the MMC host is reset, reprogram all the keyslots to ensure that
the software state stays in sync with the hardware state.
Co-developed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-2-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test_cleanup() has same body as __mmc_test_prepare() with write
except the character to memset().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210119073705.375-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since it's doing nothing for shutdown behavior. And the callback will
be checked firstly in mmc_bus_shutdown().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210119051425.305-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The host parameter is not used in the body of mmc_sd_get_csd(),
so let's remove it. Update related code at the same time.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210118084520.241-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers for MMC hosts that accept phase corrections can take advantage
of the helper by embedding an instance of struct mmc_clk_phase_map in
their private data and invoking mmc_of_parse_clk_phase() to extract
phase parameters. It is the responsibility of the host driver to
translate and apply the extracted values to hardware as required.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-2-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Note that only _mmc_suspend() will call mmc_can_sleep(). And card is
checked before in mmc_can_poweroff_notify().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210115034506.646-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If extended CSD was not available, the eMMC driver would incorrectly
set the block size to 0, as the data_sector_size field of ext_csd
was never initialized. This issue was exposed by commit 817046ecdd
("block: Align max_hw_sectors to logical blocksize") which caused
max_sectors and max_hw_sectors to be set to 0 after setting the block
size to 0, resulting in a kernel panic in bio_split when attempting
to read from the device. Fix it by only reading the block size from
ext_csd if it is available.
Fixes: a5075eb948 ("mmc: block: Allow disabling 512B sector size emulation")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://linux-review.googlesource.com/id/If244d178da4d86b52034459438fec295b02d6e60
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210114201405.2934886-1-pcc@google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The CMD13 polling is needed for commands with R1B responses. In commit
a0d4c7eb71 ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B
response"), the intent was to introduce this for requests targeted to the
RPMB partition. However, the condition to trigger the polling loop became
wrong, leading to unnecessary polling. Let's fix the condition to avoid
this.
Fixes: a0d4c7eb71 ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B response")
Cc: stable@vger.kernel.org
Reported-by: Zhan Liu <zliua@micron.com>
Signed-off-by: Zhan Liu <zliua@micron.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20201202202320.22165-1-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SD specification v7.10 the SD express card has been added. This new
type of removable SD card, can be managed via a PCIe/NVMe based interface,
while also allowing backwards compatibility towards the legacy SD
interface.
To keep the backwards compatibility, it's required to start the
initialization through the legacy SD interface. If it turns out that the
mmc host and the SD card, both supports the PCIe/NVMe interface, then a
switch should be allowed.
Therefore, let's introduce some basic support for this type of SD cards to
the mmc core. The mmc host, should set MMC_CAP2_SD_EXP if it supports this
interface and MMC_CAP2_SD_EXP_1_2V, if also 1.2V is supported, as to inform
the core about it.
To deal with the switch to the PCIe/NVMe interface, the mmc host is
required to implement a new host ops, ->init_sd_express(). Based on the
initial communication between the host and the card, host->ios.timing is
set to either MMC_TIMING_SD_EXP or MMC_TIMING_SD_EXP_1_2V, depending on if
1.2V is supported or not. In this way, the mmc host can check these values
in its ->init_sd_express() ops, to know how to proceed with the handover.
Note that, to manage card insert/removal, the mmc core sticks with using
the ->get_cd() callback, which means it's the host's responsibility to make
sure it provides valid data, even if the card may be managed by PCIe/NVMe
at the moment. As long as the card seems to be present, the mmc core keeps
the card powered on.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1603936636-3126-1-git-send-email-rui_feng@realsil.com.cn
-----BEGIN PGP SIGNATURE-----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=LzyE
-----END PGP SIGNATURE-----
Merge tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
In mmc_queue_setup_discard() the mmc driver queue's discard_granularity
might be set as 0 (when card->pref_erase > max_discard) while the mmc
device still declares to support discard operation. This is buggy and
triggered the following kernel warning message,
WARNING: CPU: 0 PID: 135 at __blkdev_issue_discard+0x200/0x294
CPU: 0 PID: 135 Comm: f2fs_discard-17 Not tainted 5.9.0-rc6 #1
Hardware name: Google Kevin (DT)
pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
pc : __blkdev_issue_discard+0x200/0x294
lr : __blkdev_issue_discard+0x54/0x294
sp : ffff800011dd3b10
x29: ffff800011dd3b10 x28: 0000000000000000 x27: ffff800011dd3cc4 x26: ffff800011dd3e18 x25: 000000000004e69b x24: 0000000000000c40 x23: ffff0000f1deaaf0 x22: ffff0000f2849200 x21: 00000000002734d8 x20: 0000000000000008 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000394 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 00000000000008b0 x9 : ffff800011dd3cb0 x8 : 000000000004e69b x7 : 0000000000000000 x6 : ffff0000f1926400 x5 : ffff0000f1940800 x4 : 0000000000000000 x3 : 0000000000000c40 x2 : 0000000000000008 x1 : 00000000002734d8 x0 : 0000000000000000 Call trace:
__blkdev_issue_discard+0x200/0x294
__submit_discard_cmd+0x128/0x374
__issue_discard_cmd_orderly+0x188/0x244
__issue_discard_cmd+0x2e8/0x33c
issue_discard_thread+0xe8/0x2f0
kthread+0x11c/0x120
ret_from_fork+0x10/0x1c
---[ end trace e4c8023d33dfe77a ]---
This patch fixes the issue by setting discard_granularity as SECTOR_SIZE
instead of 0 when (card->pref_erase > max_discard) is true. Now no more
complain from __blkdev_issue_discard() for the improper value of discard
granularity.
This issue is exposed after commit b35fd7422c ("block: check queue's
limits.discard_granularity in __blkdev_issue_discard()"), a "Fixes:" tag
is also added for the commit to make sure people won't miss this patch
after applying the change of __blkdev_issue_discard().
Fixes: e056a1b5b6 ("mmc: queue: let host controllers specify maximum discard timeout")
Fixes: b35fd7422c ("block: check queue's limits.discard_granularity in __blkdev_issue_discard()").
Reported-and-tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20201002013852.51968-1-colyli@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a littler helper to make the somewhat arcane bd_contains checks a
little more obvious.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BDI_CAP_STABLE_WRITES is one of the few bits of information in the
backing_dev_info shared between the block drivers and the writeback code.
To help untangling the dependency replace it with a queue flag and a
superblock flag derived from it. This also helps with the case of e.g.
a file system requiring stable writes due to its own checksumming, but
not forcing it on other users of the block device like the swap code.
One downside is that we an't support the stable_pages_required bdi
attribute in sysfs anymore. It is replaced with a queue attribute which
also is writable for easier testing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reorganize the code, so that the flag is always cleared independently of
a good or bad case.
Fixes: 97a7d87e96 ("mmc: core: add a 'doing_init_tune' flag and a 'mmc_doing_tune' helper")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200914112845.21855-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We already have 'host' as a variable, so use it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our driver needs to know when tuning is in progress. 'doing_retune' only
covers re-tuning, not the initial tuning. Add another flag to detect the
initial tuning state and add a helper which tells us if any kind of
tuning is going on. Only implemented for MMC currently because that's
where we need it. SD can be added later if it becomes necessary.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver specific downgrade function makes more sense if we run it
before we set the timing to something lower, not after. Otherwise some
non-HS400 communication has already happened.
No need to convert users. There is only one currently which needs this
change in a following patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As with GPIO, UART and others, allow specifying the device index via the
aliases node in the device tree.
On embedded devices, there is often a combination of removable (e.g.
SD card) and non-removable MMC devices (e.g. eMMC).
Therefore the index might change depending on
* host of removable device
* removable card present or not
This makes it difficult to hardcode the root device, if it is on the
non-removable device. E.g. if SD card is present eMMC will be mmcblk1,
if SD card is not present at boot, eMMC will be mmcblk0.
Alternative solutions like PARTUUIDs do not cover the case where multiple
mmcblk devices contain the same image. This is a common issue on devices
that can boot both from eMMC (for regular boot) and SD cards (as a
temporary boot medium for development). When a firmware image is
installed to eMMC after a test boot via SD card, there will be no
reliable way to refer to a specific device using (PART)UUIDs oder
LABELs.
The demand for this feature has led to multiple attempts to implement
it, dating back at least to 2012 (see
https://www.spinics.net/lists/linux-mmc/msg26586.html for a previous
discussion from 2014).
All indices defined in the aliases node will be reserved for use by the
respective MMC device, moving the indices of devices that don't have an
alias up into the non-reserved range. If the aliases node is not found,
the driver will act as before.
This is a rebased and cleaned up version of
https://www.spinics.net/lists/linux-mmc/msg26588.html .
Based-on-patch-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lkml.org/lkml/2020/8/5/194
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200901085004.2512-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When reading the test description, I thought a correction of the
xfer_size was tested, which is not the case. It is tested that the
xfer_size is correct. Use 'proper xfer_size' to remove this ambiguity.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200817115838.2981-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDIO functions, SDIO cards and SD COMBO cards are exported revision
number and info strings from CISTPL_VERS_1 structure. Revision number
should indicate compliance of standard and info strings should contain
product information in same format as product information for PCMCIA cards.
Product information for PCMCIA cards should contain following strings in
this order: Manufacturer, Product Name, Lot number, Programming Conditions.
Note that not all SDIO cards export all those info strings in that order as
described in PCMCIA Metaformat Specification.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-5-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before parsing CISTPL_VERS_1 structure check that its size is at least two
bytes to prevent buffer overflow.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI changed from using a tasklet to finish requests, to using an IRQ
thread i.e. commit c07a48c265 ("mmc: sdhci: Remove finish_tasklet").
Because this increased the latency to complete requests, a preparatory
change was made to complete the request from the IRQ handler if
possible i.e. commit 19d2f695f4 ("mmc: sdhci: Call mmc_request_done()
from IRQ handler if possible"). That alleviated the situation for MMC
block devices because the MMC block driver makes use of mmc_pre_req()
and mmc_post_req() so that successful requests are completed in the IRQ
handler and any DMA unmapping is handled separately in mmc_post_req().
However SDIO was still affected, and an example has been reported with
up to 20% degradation in performance.
Looking at SDIO I/O helper functions, sdio_io_rw_ext_helper() appeared
to be a possible candidate for making use of asynchronous requests
within its I/O loops, but analysis revealed that these loops almost
never iterate more than once, so the complexity of the change would not
be warrented.
Instead, mmc_pre_req() and mmc_post_req() are added before and after I/O
submission (mmc_wait_for_req) in mmc_io_rw_extended(). This still has
the potential benefit of reducing the duration of interrupt handlers, as
well as addressing the latency issue for SDHCI. It also seems a more
reasonable solution than forcing drivers to do everything in the IRQ
handler.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: c07a48c265 ("mmc: sdhci: Remove finish_tasklet")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200903082007.18715-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCgAvFiEEBpT5eoXrXCwVQwEKEnMQ0APhK1gFAl8pPQIRHG1pbmdvQGtl
cm5lbC5vcmcACgkQEnMQ0APhK1j0Jw/+LlSyX6gD2ATy3cizGL7DFPZogD5MVKTb
IXbhXH/ACpuPQlBe1+haRLbJj6XfXqbOlAleVKt7eh+jZ1jYjC972RCSTO4566mJ
0v8Iy9kkEeb2TDbYx1H3bnk78lf85t0CB+sCzyKUYFuTrXU04eRj7MtN3vAQyRQU
xJg83x/sT5DGdDTP50sL7lpbwk3INWkD0aDCJEaO/a9yHElMsTZiZBKoXxN/s30o
FsfzW56jqtng771H2bo8ERN7+abwJg10crQU5mIaLhacNMETuz0NZ/f8fY/fydCL
Ju8HAdNKNXyphWkAOmixQuyYtWKe2/GfbHg8hld0jmpwxkOSTgZjY+pFcv7/w306
g2l1TPOt8e1n5jbfnY3eig+9Kr8y0qHkXPfLfgRqKwMMaOqTTYixEzj+NdxEIRX9
Kr7oFAv6VEFfXGSpb5L1qyjIGVgQ5/JE/p3OC3GHEsw5VKiy5yjhNLoSmSGzdS61
1YurVvypSEUAn3DqTXgeGX76f0HH365fIKqmbFrUWxliF+YyflMhtrj2JFtejGzH
Md3RgAzxusE9S6k3gw1ev4byh167bPBbY8jz0w3Gd7IBRKy9vo92h6ZRYIl6xeoC
BU2To1IhCAydIr6hNsIiCSDTgiLbsYQzPuVVovUxNh+l1ZvKV2X+csEHhs8oW4pr
4BRU7dKL2NE=
=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
- Add a new host cap bit and a corresponding DT property, to support power
cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host:
- Convert a few DT bindings to the json-schema
- mtk-sd: Add support for command queue through cqhci
- mtk-sd: Add support for the MT6779 variant
- renesas_sdhi_internal_dmac: Fix dma unmapping in the error path
- sdhci_am654: Add support for the AM65x PG2.0 variant
- sdhci_am654: Extend support for phys/clocks
- sdhci-cadence: Drop incorrect HW tuning for SD mode
- sdhci-msm: Add support for interconnect bandwidth scaling
- sdhci-msm: Enable internal voltage control
- sdhci-msm: Enable low power state for pinctrls
- sdhci-of-at91: Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli: Improve clock handling for GL975x
- sdhci-pci-o2micro: Add HW tuning for SDR104 mode
- sdhci-pci-o2micro: Fix support for O2 host controller Seabird1
-----BEGIN PGP SIGNATURE-----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=AwwR
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
The commit 5a36d6bcdf ("mmc: core: Add DT-bindings for
MMC_CAP2_FULL_PWR_CYCLE") added the "full-pwr-cycle" property which
is possible to perform a full power cycle of the card at any time.
However, some environment (like r8a77951-salvator-xs) is possible
to perform a full power cycle of the card in suspend via firmware
(PSCI on arm-trusted-firmware). So, in worst case, since we are
not doing a graceful shutdown of the eMMC device (just cut VCCQ
while the eMMC is "sleeping") in suspend, it could lead to internal
data corruptions. So, add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
to do a graceful shutdown which issues Power Off notification
before entering system suspend.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594123122-13156-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Correcting this misspelling squashes the following W=1 build warning(s):
mmc/core/queue.c:212: warning: Function parameter or member 'mq' not described in '__mmc_init_request'
mmc/core/queue.c:212: warning: Excess function parameter 'q' description in '__mmc_init_request'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-8-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remainder of the kerneldoc descriptions look present and correct.
Fixes the following W=1 kernel build warnings:
drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'mmc' not described in 'mmc_regulator_set_vqmmc'
drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'ios' not described in 'mmc_regulator_set_vqmmc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-4-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add missing kerneldoc entry for sdio_set_host_pm_flags()'s 'flag'
function argument.
Fixes the following W=1 kernel build warning:
kernel/drivers/mmc/core/sdio_io.c:722: warning: Function parameter or member 'flags' not described in 'sdio_set_host_pm_flags'
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-3-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all source files which include quirks.h make use of the all of
the available fixup information. When this happens the compiler
complains that some constant variables are defined by never used.
We can fix this by telling the compiler that this intentional by
simply marking them as __maybe_unused.
Fixes the following W=1 kernel build warnings:
In file included from drivers/mmc/core/sdio.c:22:
drivers/mmc/core/quirks.h:105:31: warning: ‘mmc_ext_csd_fixups’ defined but not used [-Wunused-const-variable=]
105 | static const struct mmc_fixup mmc_ext_csd_fixups[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
In file included from drivers/mmc/core/mmc.c:25:
drivers/mmc/core/quirks.h:123:31: warning: ‘sdio_fixup_methods’ defined but not used [-Wunused-const-variable=]
123 | static const struct mmc_fixup sdio_fixup_methods[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
Cc: Andrei Warkentin <andreiw@motorola.com>
Cc: Martin Mares <mj@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-2-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the default power mode, MMC_POWER_UNDEFINED, in mmc_alloc_host() rather
than in mmc_start_host(). This enables host drivers to make use of the
initial state during ->probe().
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link:
https://lore.kernel.org/r/1592919288-1020-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In current code logic, when work in SDR12/SDR25 mode, the final clock
rate is incorrect, just the legancy 400KHz, because the
card->sw_caps.sd3_bus_mode do not has the flag SD_MODE_UHS_SDR12 or
SD_MODE_UHS_SDR25. Besides, SDIO_SPEED_SDR12 is actually value 0, and
every mode need to config the timing and clock rate, so remove the
‘if’ operator.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Tested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1592813959-5914-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 6b5eda369a ("sdio: put active devices into 1-bit mode during
suspend") disabled 4-bit mode during system suspend. After this patch,
commit 7310ece86a ("mmc: implement SD-combo (IO+mem) support") used
new sdio_enable_4bit_bus() instead of sdio_enable_wide() to support
SD-combo cards, also for card resume. However, no corresponding support
added during suspend. That is not correct. Let's fix it.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200609081431.6376-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card type is SD combo(MMC_TYPE_SD_COMBO) and the memory part does
not support wider bus(SD_SCR_BUS_WIDTH_4), nothing will be done except
return 0. However, we should check whether IO part support wider bus or
not. We should use available IO ability if supported.
In addition, there's a duplicated check to MMC_CAP_4_BIT_DATA since
sdio_enable_wide() will include that check. And we can also save one
call site to sdio_enable_wide() after this change.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200608103009.5000-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should return any possible error returned by mmc_io_rw_direct()
rather than only -EIO in sdio_disable_func() failure path.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200604100102.13572-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The approach to allow userspace ~5s to consume the uevent, which is
triggered when a new card is inserted/initialized, currently requires the
mmc host to support system wakeup.
This is unnecessary limiting, especially for an mmc host that relies on a
GPIO IRQ for card detect. More precisely, the mmc host may not support
system wakeup for its corresponding struct device, while the GPIO IRQ still
could be configured as a wakeup IRQ via enable_irq_wake().
To support all various cases, let's simply drop the need for the wakeup
support. Instead let's always register a wakeup source and activate it for
all card detect IRQs by calling __pm_wakeup_event().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200529102341.12529-1-ulf.hansson@linaro.org
The mmc driver doesn't support event notifications, which means
that check_disk_change is a no-op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the call to blk_should_fake_timeout out of blk_mq_complete_request
and into the drivers, skipping call sites that are obvious error
handlers, and remove the now superflous blk_mq_force_complete_rq helper.
This ensures we don't keep injecting errors into completions that just
terminate the Linux request after the hardware has been reset or the
command has been aborted.
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
In this case, use fifo_low, because it only cares about being above
SCHED_NORMAL. Effectively no change in behaviour.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Device/vendor ids from Common CIS (Card Information Structure) may be
different as device/vendor ids from CIS on particular SDIO function.
Kernel currently exports only device/vendor ids from SDIO functions and not
"main" device/vendor ids from Common CIS.
This patch exports "main" device/vendor ids for SDIO and SD combo cards at
top level mmc device in sysfs hierarchy.
Userspace can use e.g. udev rules to correctly match whole SDIO card based
on Common CIS device/vendor id and not only one particular SDIO function.
Having this information in userspace also helps developers to debug whole
SDIO card as e.g. kernel mmc quirks use device/vendor ids from Common CIS
and not from particular SDIO function. Also it allows to write userspace
applications which list all connected SDIO cards based on CIS ids.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO non-combo cards are not handled by mmc_block driver and do not have
accessible CID register which is used for MMC_NAME= construction.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-1-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell SDIO device ID 0x9134 is used in SDIO Common CIS (Card Information
Structure) and not in SDIO wlan function (with ID 1). SDIO Common CIS is
accessed by function ID 0.
So change this misleading macro name to SDIO_DEVICE_ID_MARVELL_8887_F0 as
it does not refer to wlan function. It refers to function 0.
Wlan module on this SDIO card is available at function ID 1 and is
identified by different SDIO device ID 0x9135. Kernel quirks for SDIO
devices are matched against device ID from SDIO Common CIS. Therefore
device ID used in quirk is correct, just has misleading name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Step by step, mmc host drivers and the mmc core have been improved in
regards to support erase/discard/trim operations. We have now reached a
point when it no longer seems reasonable to use an opt-in approach to
enable the functionality. Therefore, let's switch to make the operations
always supported.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508112853.23525-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Following eMMC JEDEC JESD84-B51 standard, an enhanced form of
rpmb is supported. What this enhanced mode supports is in addition
to be able to write one rpmb or two rpmb frames at a time,
32 frames can be written at a time.
Expose this information present in ext csd field so that the
user space application that wants to make use of this can do so.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1588341189-4371-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the comment in mmc_sdio_reinit_card(), some SDIO cards may
require a "[CMD5,5,3,7] init sequence", which isn't always obeyed in
mmc_sdio_init_card(). Especially, when we end up retrying the UHS-I
specific initialization, there is a missing CMD5.
Let's update the code to make the behaviour consistent and let's also take
the opportunity to clean up the code a bit, to avoid open coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-5-ulf.hansson@linaro.org
While initializing an SDIO card in mmc_sdio_init_card(), we may need to
retry the UHS-I specific initialization, in case the first attempt fails.
This leads to resending a CMD8, but also to restart from scratch with the
so called OCR mask negotiations. This is unnecessary as we already have a
negotiated OCR mask, so let's use that instead. In this way, the behaviour
also becomes more consistent with other similar paths.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-4-ulf.hansson@linaro.org
Over the years, the code in mmc_sdio_init_card() has grown to become quite
messy. Unfortunate this has also lead to that several paths are leaking
memory in form of an allocated struct mmc_card, which includes additional
data, such as initialized struct device for example.
Unfortunate, it's a too complex task find each offending commit. Therefore,
this change fixes all memory leaks at once.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-3-ulf.hansson@linaro.org
During some scenarios mmc_sdio_init_card() runs a retry path for the UHS-I
specific initialization, which leads to removal of the previously allocated
card. A new card is then re-allocated while retrying.
However, in one of the corresponding error paths we may end up to remove an
already removed card, which likely leads to a NULL pointer exception. So,
let's fix this.
Fixes: 5fc3d80ef4 ("mmc: sdio: don't use rocr to check if the card could support UHS mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-2-ulf.hansson@linaro.org
Fixes coccicheck warning:
drivers/mmc/core/debugfs.c:222:0-23: WARNING: mmc_clock_fops should be
defined with DEFINE_DEBUGFS_ATTRIBUTE
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files
Fixes: 703aae3d09 ("mmc: add a file to debugfs for changing host clock at runtime")
Fixes: a04c50aaa9 ("mmc: core: no need to check return value of debugfs_create functions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1587633319-19835-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the well defined HIGH_SPEED_BUS_SPEED macro in mmc_sd_switch_hs()
to make code more readable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200410145643.630b0731@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adjust mmc_regulator_set_vqmmc() to return 1 if the voltage switch was
skipped because the regulator voltage was already correct. This allows
drivers to detect such condition and possibly skip various voltage
switching extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-2-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data structure member “rpmb->md” was passed to a call of the function
“mmc_blk_put” after a call of the function “put_device”. Reorder these
function calls to keep the data accesses consistent.
Fixes: 1c87f73578 ("mmc: block: Fix bug when removing RPMB chardev ")
Signed-off-by: Peng Hao <richard.peng@oppo.com>
Cc: stable@vger.kernel.org
[Uffe: Fixed up mangled patch and updated commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
First, it should be noted that the CQE timeout (60 seconds) is substantial
so a CQE request that times out is really stuck, and the race between
timeout and completion is extremely unlikely. Nevertheless this patch
fixes an issue with it.
Commit ad73d6fead ("mmc: complete requests from ->timeout")
preserved the existing functionality, to complete the request.
However that had only been necessary because the block layer
timeout handler had been marking the request to prevent it from being
completed normally. That restriction was removed at the same time, the
result being that a request that has gone will have been completed anyway.
That is, the completion was unnecessary.
At the time, the unnecessary completion was harmless because the block
layer would ignore it, although that changed in kernel v5.0.
Note for stable, this patch will not apply cleanly without patch "mmc:
core: Fix recursive locking issue in CQE recovery path"
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: ad73d6fead ("mmc: complete requests from ->timeout")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200508062227.23144-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Consider the following stack trace
-001|raw_spin_lock_irqsave
-002|mmc_blk_cqe_complete_rq
-003|__blk_mq_complete_request(inline)
-003|blk_mq_complete_request(rq)
-004|mmc_cqe_timed_out(inline)
-004|mmc_mq_timed_out
mmc_mq_timed_out acquires the queue_lock for the first
time. The mmc_blk_cqe_complete_rq function also tries to acquire
the same queue lock resulting in recursive locking where the task
is spinning for the same lock which it has already acquired leading
to watchdog bark.
Fix this issue with the lock only for the required critical section.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Suggested-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588868135-31783-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the request completion path with CQE, request type is being checked
after the request is getting completed. This is resulting in returning
the wrong request type and leading to the IO hang issue.
ASYNC request type is getting returned for DCMD type requests.
Because of this mismatch, mq->cqe_busy flag is never getting cleared
and the driver is not invoking blk_mq_hw_run_queue. So requests are not
getting dispatched to the LLD from the block layer.
All these eventually leading to IO hang issues.
So, get the request type before completing the request.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588775643-18037-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following sparse warning:
drivers/mmc/core/mmc_ops.c:881:5: warning: symbol 'mmc_interrupt_hpi'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Fixes: 55c2b8b9a3 ("mmc: core: Re-work the code for eMMC sanitize")
Link: https://lore.kernel.org/r/20200403034727.11879-1-yanaijie@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path for sanitize operations that completes with -ETIMEDOUT, is
tightly coupled with the internal request handling code of the core. More
precisely, mmc_wait_for_req_done() checks for specific sanitize errors.
This is not only inefficient as it affects all types of requests, but also
hackish.
Therefore, let's improve the behaviour by moving the error path out of the
mmc core. To do that, retuning needs to be held while running the sanitize
operation.
Moreover, to avoid exporting unnecessary symbols to the mmc block module,
let's move the code into the mmc_ops.c file. While updating the actual
code, let's also take the opportunity to clean up some of the mess around
it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200316152152.15122-1-ulf.hansson@linaro.org
Supply a separate sg list for each of the request in non-blocking
IO test cases where two requests will be issued at same time.
Otherwise, sg memory may get unmapped when a request is done while
same memory is being accessed by controller from the other request,
and it leads to iommu errors with below call stack:
__arm_lpae_unmap+0x2e0/0x478
arm_lpae_unmap+0x54/0x70
arm_smmu_unmap+0x64/0xa4
__iommu_unmap+0xb8/0x1f0
iommu_unmap_fast+0x38/0x48
__iommu_dma_unmap+0x88/0x108
iommu_dma_unmap_sg+0x90/0xa4
sdhci_post_req+0x5c/0x78
mmc_test_start_areq+0x10c/0x120 [mmc_test]
mmc_test_area_io_seq+0x150/0x264 [mmc_test]
mmc_test_rw_multiple+0x174/0x1c0 [mmc_test]
mmc_test_rw_multiple_sg_len+0x44/0x6c [mmc_test]
mmc_test_profile_sglen_wr_nonblock_perf+0x6c/0x94 [mmc_test]
mtf_test_write+0x238/0x3cc [mmc_test]
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582714668-17247-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case the host specify a max_busy_timeout, we need to validate that the
needed timeout for the HPI command conforms to that requirement. If that's
not the case, let's convert from a R1B response to a R1 response, as to
instruct the host to avoid HW busy detection.
Additionally, when R1B is used we must also inform the host about the busy
timeout for the command, so let's do that via updating cmd.busy_timeout.
Finally, when R1B is used and in case the host supports HW busy detection,
there should be no need for doing polling, so then skip that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-12-ulf.hansson@linaro.org
Rather than open coding the polling loop in mmc_interrupt_hpi(), let's
convert to use mmc_poll_for_busy().
Note that, moving to mmc_poll_for_busy() for HPI also improves the
behaviour according to below.
- Adds support for polling via the optional ->card_busy() host ops.
- Require R1_READY_FOR_DATA to be set in the CMD13 response before exiting
the polling loop.
- Adds a throttling mechanism to avoid CPU hogging when polling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-11-ulf.hansson@linaro.org
The 'u32 *status' is unused by the caller, so let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-10-ulf.hansson@linaro.org
Rather than open coding the polling loop in mmc_do_erase(), let's convert
to use mmc_poll_for_busy().
To allow a slightly different error parsing during polling, compared to the
__mmc_switch() case, a new in-parameter to mmc_poll_for_busy() is needed,
but other than that the conversion is straight forward.
Besides addressing the open coding issue, moving to mmc_poll_for_busy() for
erase/trim/discard improves the behaviour according to below.
- Adds support for polling via the optional ->card_busy() host ops.
- Returns zero to indicate success when the final polling attempt finds the
card non-busy, even if the timeout expired.
- Exits the polling loop when state moves to R1_STATE_TRAN, rather than
when leaving R1_STATE_PRG.
- Decreases the starting range for throttling to 32-64us.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-9-ulf.hansson@linaro.org
Through mmc_poll_for_busy() a CMD13 may be sent to get the status of the
(e)MMC card. If the state of the card is R1_STATE_PRG, the card is
considered as being busy, which means we continue to poll with CMD13. This
seems to be sufficient, but it's also unnecessary fragile, as it means a
new command/request could potentially be sent to the card when it's in an
unknown state.
To try to improve the situation, but also to move towards a more consistent
CMD13 polling behaviour in the mmc core, let's deploy the same policy we
use for regular I/O write requests. In other words, let's check that card
returns to the R1_STATE_TRAN and that the R1_READY_FOR_DATA bit is set in
the CMD13 response, before exiting the polling loop.
Note that, potentially this changed behaviour could lead to unnecessary
waiting for the timeout to expire, if the card for some reason, moves to an
unexpected error state. However, as we bail out from the polling loop when
R1_SWITCH_ERROR bit is set or when the CMD13 fails, this shouldn't be an
issue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-8-ulf.hansson@linaro.org
To allow subsequent changes to re-use the code from the static function
mmc_blk_in_tran_state(), let's move it to a public header. While at it,
let's also rename it to mmc_ready_for_data(), as to try to better describe
its purpose.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-7-ulf.hansson@linaro.org
To make the code more readable, move the part that gets the busy status of
the card out into a separate function, mmc_busy_status(). Then call it from
mmc_poll_for_busy().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-6-ulf.hansson@linaro.org
The use_busy_signal in-parameter is set true by all callers of
__mmc_switch(), hence it's redundant so drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-5-ulf.hansson@linaro.org
To simplify code, let's extend mmc_switch_status() to cope with needs
addressed in __mmc_switch_status(). Then move all users to the updated
mmc_switch_status() API and drop __mmc_switch_status() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-4-ulf.hansson@linaro.org
The last user of MMC_OPS_TIMEOUT_MS was recently removed, however the
define stayed around. Let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-3-ulf.hansson@linaro.org
In mmc_poll_for_busy() we loop continuously, either by sending a CMD13 or
by invoking the ->card_busy() host ops, as to detect when the card stops
signaling busy. This behaviour is problematic as it may cause CPU hogging,
especially when the busy signal time reaches beyond a few ms.
Let's fix the issue by adding a throttling mechanism, that inserts a
usleep_range() in between the polling attempts. The sleep range starts at
32-64us, but increases for each loop by a factor of 2, up until the range
reaches ~32-64ms. In this way, we are able to keep the loop fine-grained
enough for short busy signaling times, while also not hogging the CPU for
longer times.
Note that, this change is inspired by the similar throttling mechanism that
we already use for mmc_do_erase().
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-2-ulf.hansson@linaro.org
Enable the MMC host software queue for the SD card if the host controller
supports the MMC host software queue.
On my Spreadtrum platform, I did not see any obvious performance changes
in 4K block size when changing to use hsq for the SD cards, I think the
reason is the SD card works at a low speed on my platform, and most of
time is spent in the hardware. But we can see some obvious improvements
when enabling the packed request based on hsq, that's why we still add hsq
support for the SD cards.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/0065b4631fef2d61c3b89d14a4ea4f2b7499ea56.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now the MMC read/write stack will always wait for previous request is
completed by mmc_blk_rw_wait(), before sending a new request to hardware,
or queue a work to complete request, that will bring context switching
overhead and spend some extra time to poll the card for busy completion
for I/O writes via sending CMD13, especially for high I/O per second
rates, to affect the IO performance.
Thus this patch introduces MMC software queue interface based on the
hardware command queue engine's interfaces, which is similar with the
hardware command queue engine's idea, that can remove the context
switching. Moreover we set the default queue depth as 64 for software
queue, which allows more requests to be prepared, merged and inserted
into IO scheduler to improve performance, but we only allow 2 requests
in flight, that is enough to let the irq handler always trigger the
next request without a context switch, as well as avoiding a long latency.
Moreover the host controller should support HW busy detection for I/O
operations when enabling the host software queue. That means, the host
controller must not complete a data transfer request, until after the
card stops signals busy.
From the fio testing data in cover letter, we can see the software
queue can improve some performance with 4K block size, increasing
about 16% for random read, increasing about 90% for random write,
though no obvious improvement for sequential read and write.
Moreover we can expand the software queue interface to support MMC
packed request or packed command in future.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/4409c1586a9b3ed20d57ad2faf6c262fc3ccb6e2.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busy timeout for the CMD5 to put the eMMC into sleep state, is specific
to the card. Potentially the timeout may exceed the host->max_busy_timeout.
If that becomes the case, mmc_sleep() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200311092036.16084-1-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busy timeout that is computed for each erase/trim/discard operation,
can become quite long and may thus exceed the host->max_busy_timeout. If
that becomes the case, mmc_do_erase() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out that some host controllers can't use R1B for CMD6 and
other commands that have R1B associated with them. Therefore invent a new
host cap, MMC_CAP_NEED_RSP_BUSY to let them specify this.
In __mmc_switch(), let's check the flag and use it to prevent R1B responses
from being converted into R1. Note that, this also means that the host are
on its own, when it comes to manage the busy timeout.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All callers of __mmc_switch() should now be specifying a valid timeout for
the CMD6 command. However, just to be sure, let's print a warning and
default to use the generic_cmd6_time in case the provided timeout_ms
argument is zero.
In this context, let's also simplify some of the corresponding code and
clarify some related comments.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-4-ulf.hansson@linaro.org
The INAND_CMD38_ARG_EXT_CSD is a vendor specific EXT_CSD register, which is
used to prepare an erase/trim operation. However, it doesn't make sense to
use a timeout of 10 minutes while updating the register, which becomes the
case when the timeout_ms argument for mmc_switch() is set to zero.
Instead, let's use the generic_cmd6_time, as that seems like a reasonable
timeout to use for these cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-3-ulf.hansson@linaro.org
The timeout values used while waiting for a CMD6 for BKOPS or a CACHE_FLUSH
to complete, are not defined by the eMMC spec. However, a timeout of 10
minutes as is currently being used, is just silly for both of these cases.
Instead, let's specify more reasonable timeouts, 120s for BKOPS and 30s for
CACHE_FLUSH.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-2-ulf.hansson@linaro.org
There are a few places around the code that invert inverted and possibly
inverted CD line. That's really confusing. Squash them all into one place
in mmc_gpiod_request_cd(). MMC_CAP2_CD_ACTIVE_HIGH is used analogously to
WP line: in GPIO mode it is used only at probe time to switch polarity, for
native mode it is left as is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/db189b715596d63caf8c6a088bddc71dd69a879b.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use MMC_CAP2_RO_ACTIVE_HIGH flag as indicator if GPIO line is to be
inverted compared to DT/platform-specified polarity. The flag is not used
after init in GPIO mode anyway. No functional changes intended.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/a60f563f11bbff821da2fa2949ca82922b144860.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With large eMMC cards, it is possible to create general purpose
partitions that are bigger than 4GB. The size member of the mmc_part
struct is only an unsigned int which overflows for gp partitions larger
than 4GB. Change this to a u64 to handle the overflow.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wl1251 and wl1271 have different vendor id and device id.
So we need to handle both with sdio quirks.
Fixes: 884f386078 ("mmc: core: move some sdio IDs out of quirks file")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It have turned out that it's not a good idea to unconditionally do a power
cycle and then to re-initialize the SDIO card, as currently done through
mmc_hw_reset() -> mmc_sdio_hw_reset(). This because there may be multiple
SDIO func drivers probed, who also shares the same SDIO card.
To address these scenarios, one may be tempted to use a notification
mechanism, as to allow the core to inform each of the probed func drivers,
about an ongoing HW reset. However, supporting such an operation from the
func driver point of view, may not be entirely trivial.
Therefore, let's use a more simplistic approach to solve the problem, by
instead forcing the card to be removed and re-detected, via scheduling a
rescan-work. In this way, we can rely on existing infrastructure, as the
func driver's ->remove() and ->probe() callbacks, becomes invoked to deal
with the cleanup and the re-initialization.
This solution may be considered as rather heavy, especially if a func
driver doesn't share its card with other func drivers. To address this,
let's keep the current immediate HW reset option as well, but run it only
when there is one func driver probed for the card.
Finally, to allow the caller of mmc_hw_reset(), to understand if the reset
is being asynchronously managed from a scheduled work, it returns 1
(propagated from mmc_sdio_hw_reset()). If the HW reset is executed
successfully and synchronously it returns 0, which maintains the existing
behaviour.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Upfront in mmc_rescan() we use the host->rescan_entered flag, to allow
scanning only once for non-removable cards. Therefore, it's also not
possible that we can have a corresponding card bus attached (host->bus_ops
is NULL), when we are scanning non-removable cards.
For this reason, let' drop the check for mmc_card_is_removable() as it's
redundant.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC IOCTLS with R1B responses may cause the card to enter the busy state,
which means it's not ready to receive a new request. To prevent new
requests from being sent to the card, use a CMD13 polling loop to verify
that the card returns to the transfer state, before completing the request.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prepare for more users of card_busy_detect(), let's drop the struct
request * as an in-parameter and convert to log the error message via
dev_err() instead of pr_err().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- add dma-mapping and block layer helpers to take care of IOMMU
merging for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask (me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
-----BEGIN PGP SIGNATURE-----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=/wGv
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- add dma-mapping and block layer helpers to take care of IOMMU merging
for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask
(me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
* tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping: (41 commits)
mmc: renesas_sdhi_internal_dmac: Add MMC_CAP2_MERGE_CAPABLE
mmc: queue: Fix bigger segments usage
arm64: use asm-generic/dma-mapping.h
swiotlb-xen: merge xen_unmap_single into xen_swiotlb_unmap_page
swiotlb-xen: simplify cache maintainance
swiotlb-xen: use the same foreign page check everywhere
swiotlb-xen: remove xen_swiotlb_dma_mmap and xen_swiotlb_dma_get_sgtable
xen: remove the exports for xen_{create,destroy}_contiguous_region
xen/arm: remove xen_dma_ops
xen/arm: simplify dma_cache_maint
xen/arm: use dev_is_dma_coherent
xen/arm: consolidate page-coherent.h
xen/arm: use dma-noncoherent.h calls for xen-swiotlb cache maintainance
arm: remove wrappers for the generic dma remap helpers
dma-mapping: introduce a dma_common_find_pages helper
dma-mapping: always use VM_DMA_COHERENT for generic DMA remap
vmalloc: lift the arm flag for coherent mappings to common code
dma-mapping: provide a better default ->get_required_mask
dma-mapping: remove the dma_declare_coherent_memory export
remoteproc: don't allow modular build
...
The commit 38c38cb732 ("mmc: queue: use bigger segments if DMA MAP
layer can merge the segments") always enables the bugger segments
if DMA MAP layer can merge the segments, but some controllers (SDHCI)
have strictly limitation about the segments size, and then the commit
breaks on the controllers.
To fix the issue, this patch adds a new flag MMC_CAP2_MERGE_CAPABLE
into the struct mmc_host and the bigger segments usage is disabled
as default.
Reported-by: Thierry Reding <treding@nvidia.com>
Fixes: 38c38cb732 ("mmc: queue: use bigger segments if DMA MAP layer can merge the segments")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
System suspend/resume of SDIO cards, with SDIO IRQs enabled and when using
MMC_CAP2_SDIO_IRQ_NOTHREAD is unfortunate still suffering from a fragile
behaviour. Some problems have been taken care of so far, but more issues
remains.
For example, calling the ->ack_sdio_irq() callback to let host drivers
re-enable the SDIO IRQs is a bad idea, unless the IRQ have been consumed,
which may not be the case during system suspend/resume. This may lead to
that a host driver re-signals the same SDIO IRQ over and over again,
causing a storm of IRQs and gives a ping-pong effect towards the
sdio_irq_work().
Moreover, calling the ->enable_sdio_irq() callback at system resume to
re-enable already enabled SDIO IRQs for the host, causes the runtime PM
count for some host drivers to become in-balanced. This then leads to the
host to remain runtime resumed, no matter if it's needed or not.
To fix these problems, let's check if process_sdio_pending_irqs() actually
consumed the SDIO IRQ, before we continue to ack the IRQ by invoking the
->ack_sdio_irq() callback.
Additionally, there should be no need to re-enable SDIO IRQs as the host
driver already knows if they were enabled at system suspend, thus also
whether it needs to re-enable them at system resume. For this reason, drop
the call to ->enable_sdio_irq() during system resume.
In regards to these changes there is yet another issue, which is when there
is an SDIO IRQ being signaled by the host driver, but after the SDIO card
has been system suspended. Currently these IRQs are just thrown away, while
we should at least make sure to try to consume them when the SDIO card has
been system resumed. Fix this by queueing a sdio_irq_work() after we system
resumed the SDIO card.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make sure SDIO func drivers behaves correctly during system
suspend/resume, let add a WARN_ON in case the condition is a non-powered
SDIO card and there are some SDIO IRQs still being claimed.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the MMC_CAP2_SDIO_IRQ_NOTHREAD case and when using sdio_signal_irq(),
the ->ack_sdio_irq() is already mandatory, which was not the case for those
host drivers that called sdio_run_irqs() directly.
As there are no longer any drivers calling sdio_run_irqs(), let's clarify
the code by dropping the unnecessary check and explicitly state that the
callback is mandatory in the header file.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdio_irq_pending flag is used to let host drivers indicate that it has
signaled an IRQ. If that is the case and we only have a single SDIO func
that have claimed an SDIO IRQ, our assumption is that we can avoid reading
the SDIO_CCCR_INTx register and just call the SDIO func irq handler
immediately. This makes sense, but the flag is set/cleared in a somewhat
messy order, let's fix that up according to below.
First, the flag is currently set in sdio_run_irqs(), which is executed as a
work that was scheduled from sdio_signal_irq(). To make it more implicit
that the host have signaled an IRQ, let's instead immediately set the flag
in sdio_signal_irq(). This also makes the behavior consistent with host
drivers that uses the legacy, mmc_signal_sdio_irq() API. This have no
functional impact, because we don't expect host drivers to call
sdio_signal_irq() until after the work (sdio_run_irqs()) have been executed
anyways.
Second, currently we never clears the flag when using the sdio_run_irqs()
work, but only when using the sdio_irq_thread(). Let make the behavior
consistent, by moving the flag to be cleared inside the common
process_sdio_pending_irqs() function. Additionally, tweak the behavior of
the flag slightly, by avoiding to clear it unless we processed the SDIO
IRQ. The purpose with this at this point, is to keep the information about
whether there have been an SDIO IRQ signaled by the host, so at system
resume we can decide to process it without reading the SDIO_CCCR_INTx
register.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To improve code quality, let's move the code that gets pending SDIO IRQs
from process_sdio_pending_irqs() into a dedicated function.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
[Ulf: Converted function into static]
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turns out the commit 3a0681c744 ("mmc: core: do not retry CMD6 in
__mmc_switch()") breaks initialization of a Toshiba THGBMNG5 eMMC card,
when using the meson-gx-mmc.c driver on a custom board based on Amlogic
A113D.
The CMD6 that switches the card into HS200 mode is then one that fails and
according to the below printed messages from the log:
[ 1.648951] mmc0: mmc_select_hs200 failed, error -84
[ 1.648988] mmc0: error -84 whilst initialising MMC card
After some analyze, it turns out that adding a delay of ~5ms inside
mmc_select_bus_width() but after mmc_compare_ext_csds() has been executed,
also fixes the problem. Adding yet some more debug code, trying to figure
out if potentially the card could be in a busy state, both by using CMD13
and ->card_busy() ops concluded that this was not the case.
Therefore, let's simply revert the commit that dropped support for retrying
of CMD6, as this also fixes the problem.
Fixes: 3a0681c744 ("mmc: core: do not retry CMD6 in __mmc_switch()")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Kaisrlik <ja.kaisrlik@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the max_segs of a mmc host is smaller than 512, the mmc
subsystem tries to use 512 segments if DMA MAP layer can merge
the segments, and then the mmc subsystem exposes such information
to the block layer by using blk_queue_can_use_dma_map_merging().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The OCR register defines the supported range of VDD voltages for SD cards.
However, it has turned out that some SD cards reports an invalid voltage
range, for example having bit7 set.
When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from
the invalid VDD range, this triggers the core to run a power cycle of the
card to try to initialize it at the lowest common supported voltage.
Obviously this fails, since the card can't support it.
Let's fix this problem, by clearing invalid bits from the read OCR register
for SD cards, before proceeding with the VDD voltage negotiation.
Cc: stable@vger.kernel.org
Reported-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Philip Langdale <philipl@overt.org>
Tested-by: Philip Langdale <philipl@overt.org>
Tested-by: Manuel Presnitz <mail@mpy.de>
While using the mmc_spi driver occasionally errors like this popped up:
mmcblk0: error -84 transferring data end_request: I/O error, dev mmcblk0, sector 581756
I looked on the Internet for occurrences of the same problem and came
across a helpful post [1]. It includes source code to reproduce the bug.
There is also an analysis about the cause. During transmission data in the
supplied buffer is being modified. Thus the previously calculated checksum
is not correct anymore.
After some digging I found out that device drivers are supposed to report
they need stable writes. To fix this I set the appropriate flag at queue
initialization if CRC checksumming is enabled for that SPI host.
[1]
https://groups.google.com/forum/#!msg/sim1/gLlzWeXGFr8/KevXinUXfc8J
Signed-off-by: Andreas Koop <andreas.koop@zf.com>
[shihpo: Rebase on top of v5.3-rc1]
Signed-off-by: ShihPo Hung <shihpo.hung@sifive.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
CC: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Let the dma map ops deal with bouncing and drop dma_max_pfn() from the
dma-mapping interface for ARM
- Convert the generic MMC DT doc to YAML schemas
- Drop questionable support for powered-on re-init of SDIO cards at
runtime resume and for SDIO HW reset
- Prevent questionable re-init of powered-on removable SDIO cards at
system resume
- Cleanup and clarify some SDIO core code
MMC host:
- tmio: Make runtime PM enablement more flexible for variants
- tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt to clarify
- sdhci-pci: Add support for Intel EHL
- sdhci-pci-o2micro: Enable support for 8-bit bus
- sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
- sdhci-of-esdhc: Improve clock management and tuning
- sdhci_am654: Enable support for 4 and 8-bit bus on J721E
- sdhci-sprd: Use pinctrl for a proper signal voltage switch
- sdhci-sprd: Add support for HS400 enhanced strobe mode
- sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the clock
- sdhci-sprd: Add support for optional gate clock
- sunxi-mmc: Convert DT doc to YAML schemas
- meson-gx: Add support for broken DRAM access for DMA
MEMSTICK core:
- Fixup error path of memstick_init()
-----BEGIN PGP SIGNATURE-----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=vkWp
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Let the dma map ops deal with bouncing and drop dma_max_pfn() from
the dma-mapping interface for ARM
- Convert the generic MMC DT doc to YAML schemas
- Drop questionable support for powered-on re-init of SDIO cards at
runtime resume and for SDIO HW reset
- Prevent questionable re-init of powered-on removable SDIO cards at
system resume
- Cleanup and clarify some SDIO core code
MMC host:
- tmio: Make runtime PM enablement more flexible for variants
- tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt
to clarify
- sdhci-pci: Add support for Intel EHL
- sdhci-pci-o2micro: Enable support for 8-bit bus
- sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
- sdhci-of-esdhc: Improve clock management and tuning
- sdhci_am654: Enable support for 4 and 8-bit bus on J721E
- sdhci-sprd: Use pinctrl for a proper signal voltage switch
- sdhci-sprd: Add support for HS400 enhanced strobe mode
- sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the
clock
- sdhci-sprd: Add support for optional gate clock
- sunxi-mmc: Convert DT doc to YAML schemas
- meson-gx: Add support for broken DRAM access for DMA
MEMSTICK core:
- Fixup error path of memstick_init()"
* tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
mmc: alcor: remove a redundant greater or equal to zero comparison
mmc: sdhci-msm: fix mutex while in spinlock
mmc: sdhci_am654: Make some symbols static
dma-mapping: remove dma_max_pfn
mmc: core: let the dma map ops handle bouncing
dt-binding: mmc: rename tmio_mmc.txt to renesas,sdhi.txt
mmc: sdhci-sprd: Add pin control support for voltage switch
dt-bindings: mmc: sprd: Add pinctrl support
mmc: sdhci-sprd: Add start_signal_voltage_switch ops
mmc: sdhci-pci: Add support for Intel EHL
mmc: tmio: Use dma_max_mapping_size() instead of a workaround
mmc: sdio: Drop unused in-parameter from mmc_sdio_init_card()
mmc: sdio: Drop unused in-parameter to mmc_sdio_reinit_card()
mmc: sdio: Don't re-initialize powered-on removable SDIO cards at resume
mmc: sdio: Drop powered-on re-init at runtime resume and HW reset
mmc: sdio: Move comment about re-initialization to mmc_sdio_reinit_card()
mmc: sdio: Drop mmc_claim|release_host() in mmc_sdio_power_restore()
mmc: sdio: Turn sdio_run_irqs() into static
mmc: sdhci: Fix indenting on SDHCI_CTRL_8BITBUS
...
Just like we do for all other block drivers. Especially as the limit
imposed at the moment might be way to pessimistic for iommus.
This also means we are not going to set a bounce limit for the queue, in
case we have a dma mask. On most architectures it was never needed, the
major hold out was x86-32 with PAE, but that has been fixed by now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "powered_resume" in-parameter to mmc_sdio_init_card() has now become
redundant as all callers set it to 0. Therefore let's just drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
The "powered_resume" in-parameter to mmc_sdio_reinit_card() has now become
redundant as all callers set it to 0. Therefore let's just drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
It looks like the original idea behind always doing a re-initialization of
a removable SDIO card during system resume in mmc_sdio_resume(), is to try
to play safe to detect whether the card has been removed.
However, this seems like a really a bad idea as it will most likely screw
things up, especially when the card is expected to remain powered on during
system suspend by the SDIO func driver.
Let's fix this, simply by trusting that the detect work checks if the card
is alive and inserted, which is being scheduled at the PM_POST_SUSPEND
notification anyway.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
To use the so called powered-on re-initialization of an SDIO card, the
power to the card must obviously have stayed on. If not, the initialization
will simply fail.
In the runtime suspend case, the card is always powered off. Hence, let's
drop the support for powered-on re-initialization during runtime resume, as
it doesn't make sense.
Moreover, during a HW reset, the point is to cut the power to the card and
then do fresh re-initialization. Therefore drop the support for powered-on
re-initialization during HW reset.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: ca8971ca57 ("mmc: dw_mmc: Prevent runtime PM suspend when SDIO IRQs are enabled")
Tested-by: Douglas Anderson <dianders@chromium.org>
The comment in mmc_sdio_power_restore() belongs in mmc_sdio_reinit_card(),
which was created during a previous commit that re-factored some code. Fix
this by moving the comment into mmc_sdio_reinit_card().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
The function mmc_sdio_power_restore() is called either from
mmc_sdio_runtime_resume() or from mmc_sdio_hw_reset(). Both callers either
claims/releases the host or require its callers to do so. Therefore let's
drop the redundant calls to mmc_claim|release_host() in
mmc_sdio_power_restore().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
All external users of sdio_run_irqs() have converted into using the
preferred sdio_signal_irq() interface, thus not calling the function
directly any more. Avoid further new users of it, by turning it into
static.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Processing of SDIO IRQs must obviously be prevented while the card is
system suspended, otherwise we may end up trying to communicate with an
uninitialized SDIO card.
Reports throughout the years shows that this is not only a theoretical
problem, but a real issue. So, let's finally fix this problem, by keeping
track of the state for the card and bail out before processing the SDIO
IRQ, in case the card is suspended.
Cc: stable@vger.kernel.org
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We want SDIO drivers to be able to temporarily stop retuning when the
driver knows that the SDIO card is not in a state where retuning will
work (maybe because the card is asleep). We'll move the relevant
functions to a place where drivers can call them.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Normally when the MMC core sees an "-EILSEQ" error returned by a host
controller then it will trigger a retuning of the card. This is
generally a good idea.
However, if a command is expected to sometimes cause transfer errors
then these transfer errors shouldn't cause a re-tuning. This
re-tuning will be a needless waste of time. One example case where a
transfer is expected to cause errors is when transitioning between
idle (sometimes referred to as "sleep" in Broadcom code) and active
state on certain Broadcom WiFi SDIO cards. Specifically if the card
was already transitioning between states when the command was sent it
could cause an error on the SDIO bus.
Let's add an API that the SDIO function drivers can call that will
temporarily disable the auto-tuning functionality. Then we can add a
call to this in the Broadcom WiFi driver and any other driver that
might have similar needs.
NOTE: this makes the assumption that the card is already tuned well
enough that it's OK to disable the auto-retuning during one of these
error-prone situations. Presumably the driver code performing the
error-prone transfer knows how to recover / retry from errors. ...and
after we can get back to a state where transfers are no longer
error-prone then we can enable the auto-retuning again. If we truly
find ourselves in a case where the card needs to be retuned sometimes
to handle one of these error-prone transfers then we can always try a
few transfers first without auto-retuning and then re-try with
auto-retuning if the first few fail.
Without this change on rk3288-veyron-minnie I periodically see this in
the logs of a machine just sitting there idle:
dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't have a reproducible error case, yet our BSP team suggested that
the mmc_switch_status() command in mmc_select_hs400() should come after
the callback into the driver completing HS400 setup. It makes sense to
me because we want the status of a fully setup HS400, so it will
increase the reliability of the mmc_switch_status() command.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ba6c7ac3a2 ("mmc: core: more fine-grained hooks for HS400 tuning")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we only set the max_segment_size on the queue an IOMMU merge might
create bigger segments again, so limit the IOMMU merges as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a few memoryleaks
- Minor improvements to the card initialization sequence
- Partially support sleepy GPIO controllers for pwrseq eMMC
MMC host:
- alcor: Work with multiple-entry sglists
- alcor: Enable DMA for writes
- meson-gx: Improve tuning support
- meson-gx: Avoid clock glitch when switching to DDR modes
- meson-gx: Disable unreliable HS400 mode
- mmci: Minor updates for support of HW busy detection
- mmci: Support data transfers for the stm32_sdmmc variant
- mmci: Restructure code to better support different variants
- mtk-sd: Add support for version found on MT7620 family SOCs
- mtk-sd: Add support for the MT8516 version
- mtk-sd: Add Chaotian Jing as the maintainer
- sdhci: Reorganize request-code to convert from tasklet to workqueue
- sdhci_am654: Stabilize support for lower speed modes
- sdhci-esdhc-imx: Add HS400 support for iMX7ULP
- sdhci-esdhc-imx: Add support for iMX7ULP version
- sdhci-of-arasan: Allow to disable DCMDs via DT for CQE
- sdhci-of-esdhc: Add support for the ls1028a version
- sdhci-of-esdhc: Several fixups for errata
- sdhci-pci: Fix BYT OCP setting
- sdhci-pci: Add support for Intel CML
- sdhci-tegra: Add support for system suspend/resume
- sdhci-tegra: Add CQE support for Tegra186 WAR
- sdhci-tegra: Add support for Tegra194
- sdhci-tegra: Update HW tuning process
MEMSTICK:
- I volunteered to help as a maintainer for the memstick subsystem, which is
reflected by an update to the MAINTAINERS file. Changes are funneled through
my MMC git and we will use the linux-mmc mailing list.
MEMSTICK host:
- A few minor cleanups
-----BEGIN PGP SIGNATURE-----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=Ompt
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix a few memoryleaks
- Minor improvements to the card initialization sequence
- Partially support sleepy GPIO controllers for pwrseq eMMC
MMC host:
- alcor: Work with multiple-entry sglists
- alcor: Enable DMA for writes
- meson-gx: Improve tuning support
- meson-gx: Avoid clock glitch when switching to DDR modes
- meson-gx: Disable unreliable HS400 mode
- mmci: Minor updates for support of HW busy detection
- mmci: Support data transfers for the stm32_sdmmc variant
- mmci: Restructure code to better support different variants
- mtk-sd: Add support for version found on MT7620 family SOCs
- mtk-sd: Add support for the MT8516 version
- mtk-sd: Add Chaotian Jing as the maintainer
- sdhci: Reorganize request-code to convert from tasklet to workqueue
- sdhci_am654: Stabilize support for lower speed modes
- sdhci-esdhc-imx: Add HS400 support for iMX7ULP
- sdhci-esdhc-imx: Add support for iMX7ULP version
- sdhci-of-arasan: Allow to disable DCMDs via DT for CQE
- sdhci-of-esdhc: Add support for the ls1028a version
- sdhci-of-esdhc: Several fixups for errata
- sdhci-pci: Fix BYT OCP setting
- sdhci-pci: Add support for Intel CML
- sdhci-tegra: Add support for system suspend/resume
- sdhci-tegra: Add CQE support for Tegra186 WAR
- sdhci-tegra: Add support for Tegra194
- sdhci-tegra: Update HW tuning process
MEMSTICK:
- I volunteered to help as a maintainer for the memstick subsystem,
which is reflected by an update to the MAINTAINERS file. Changes
are funneled through my MMC git and we will use the linux-mmc
mailing list.
MEMSTICK host:
- A few minor cleanups"
* tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (87 commits)
mmc: sdhci-pci: Fix BYT OCP setting
dt-bindings: mmc: add DT bindings for ls1028a eSDHC host controller
mmc: alcor: Drop pointer to mmc_host from alcor_sdmmc_host
mmc: mtk-sd: select REGULATOR
mmc: mtk-sd: enable internal card-detect logic.
mmc: mtk-sd: add support for config found in mt7620 family SOCs.
mmc: mtk-sd: don't hard-code interrupt trigger type
mmc: core: Fix tag set memory leak
dt-bindings: mmc: Add support for MT8516 to mtk-sd
mmc: mmci: Prevent polling for busy detection in IRQ context
mmc: mmci: Cleanup mmci_cmd_irq() for busy detect
mmc: usdhi6rol0: mark expected switch fall-throughs
mmc: core: Verify SD bus width
mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP
mmc: sdhci-esdhc-imx: add pm_qos to interact with cpuidle
dt-bindings: mmc: fsl-imx-esdhc: add imx7ulp compatible string
mmc: meson-gx: add signal resampling tuning
mmc: meson-gx: remove Rx phase tuning
mmc: meson-gx: avoid clock glitch when switching to DDR modes
mmc: meson-gx: disable HS400
...
