While STRB is currently used for DATA and CRC responses, the CMD
responses from the device to the host still require ITAPDLY for
HS400 timing.
Currently what is stored for HS400 is the ITAPDLY from High Speed
mode which is incorrect. The ITAPDLY for HS400 speed mode should
be the same as ITAPDLY as HS200 timing after tuning is executed.
Add the functionality to save ITAPDLY from HS200 tuning and save
as HS400 ITAPDLY.
Fixes: a161c45f29 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-8-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ITAPDLYSEL to sdhci_j721e_4bit_set_clock function.
This allows to set the correct ITAPDLY for timings that
do not carry out tuning.
Fixes: 1accbced1c ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-7-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the OTAP/ITAP delay enable functionality is incorrect in
the am654_set_clock function. The OTAP delay is not enabled when
timing < SDR25 bus speed mode. The ITAP delay is not enabled for
timings that do not carry out tuning.
Add this OTAP/ITAP delay functionality according to the datasheet
[1] OTAPDLYENA and ITAPDLYENA for MMC0.
[1] https://www.ti.com/lit/ds/symlink/am62p.pdf
Fixes: 8ee5fc0e0b ("mmc: sdhci_am654: Update OTAPDLY writes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-4-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For DDR52 timing, DLL is enabled but tuning is not carried
out, therefore the ITAPDLY value in PHY CTRL 4 register is
not correct. Fix this by writing ITAPDLY after enabling DLL.
Fixes: a161c45f29 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-3-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the sdhci_am654 driver only supports one tuning
algorithm which should be used only when DLL is enabled. The
ITAPDLY is selected from the largest passing window and the
buffer is viewed as a circular buffer.
The new algorithm should be used when the delay chain
is enabled. The ITAPDLY is selected from the largest passing
window and the buffer is not viewed as a circular buffer.
This implementation is based off of the following paper: [1].
Also add support for multiple failing windows.
[1] https://www.ti.com/lit/an/spract9/spract9.pdf
Fixes: 13ebeae68a ("mmc: sdhci_am654: Add support for software tuning")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-2-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The err is being set to 0 and replaced every time after this
assignment. Remove this assignment as it is extraneous.
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20240307145013.2721326-1-usama.anjum@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The err is being set to 0 and replaced every time after this
assignment. Remove this assignment as it is extraneous.
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240307122129.2359553-1-usama.anjum@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240307114500.3643489-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems the of_get_named_gpio() is solely used to check
if the GPIO is present in DT as the function can return 0
if and only if it's present and it becomes in the global
number space 0. But this quite likely shows that the code
wasn't ever been tested on the systems when no GPIO is provided.
In any case, the proper test is just to call of_property_present()
without any attempts in requesting GPIO (as we haven't saved the
number or descriptor anywhere in the code).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240307121912.3676850-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Axe Yang <axe.yang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240307114348.3643034-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"PM runtime functions" was been added in sdhci-omap driver in commit
f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions") along
with "card power off and enable aggressive PM" in commit 3edf588e7f
("mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM").
Since then, the sdhci-omap driver doesn't work using mmc-hs200 mode
due to the tuning values being lost during a pm transition.
As for the sdhci_am654 driver, request a new tuning sequence before
suspend (sdhci_omap_runtime_suspend()), otherwise the device will
trigger cache flush error:
mmc1: cache flush error -110 (ETIMEDOUT)
mmc1: error -110 doing aggressive suspend
followed by I/O errors produced by fdisk -l /dev/mmcblk1boot1:
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot1, logical block 8048, async page read
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot0, logical block 8048, async page read
Don't re-tune if auto retuning is supported in HW (when SDHCI_TUNING_MODE_3
is available).
Link: https://lore.kernel.org/all/2e5f1997-564c-44e4-b357-6343e0dae7ab@smile.fr
Fixes: f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
Signed-off-by: Romain Naour <romain.naour@skf.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240315234444.816978-1-romain.naour@smile.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used in
future to allow controllers to directly trigger SPI operations (eg, from
interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages.
- A big set of updates from Uwe Kleine-König moving drivers to use APIs
with more modern terminology for controllers.
- Major overhaul of the s3c64xx driver.
- Support for Google GS101 and Samsung Exynos850.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmXvHx0ACgkQJNaLcl1U
h9ATVQf/WafEp7ddJ23bRaHZx/gBCMgv8N6mN7OBnzB2pMIGL56SPf9fGAmCUQKt
mne6fDg6/RpydG/72TFppUjRFLN9CwoJjJfQIXMgOqYuPaMEnrj1wbcXar3MeeX2
8hS1u7wKwhOuuwLmoqqMOTKyGUj2mHsBOTOo0vm4WM1s9IHhY5TG2clYv1A+KZbj
kSHE5m7YnBLwimwu0+hsXnRNHZUGKVksQ/9t7AD7/7L8aPj9jPqu1EjTS1/6IDB0
QDVyW7Z6hX7YoUx48gp+j/UFJ7ZyxTajy+0wvzPHou3KJARgFfNZWT2XvvYcpA0/
yqcpbCUwZ1AETXHcmly7YwNpPV9LBg==
=+Xw/
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used
in future to allow controllers to directly trigger SPI operations (eg,
from interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages
- A big set of updates from Uwe Kleine-König moving drivers to use
APIs with more modern terminology for controllers
- Major overhaul of the s3c64xx driver
- Support for Google GS101 and Samsung Exynos850"
* tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (122 commits)
spi: Introduce SPI_INVALID_CS and is_valid_cs()
spi: Fix types of the last chip select storage variables
spi: Consistently use BIT for cs_index_mask
spi: Exctract spi_dev_check_cs() helper
spi: Exctract spi_set_all_cs_unused() helper
spi: s3c64xx: switch exynos850 to new port config data
spi: s3c64xx: switch gs101 to new port config data
spi: s3c64xx: deprecate fifo_lvl_mask, rx_lvl_offset and port_id
spi: s3c64xx: get rid of the OF alias ID dependency
spi: s3c64xx: introduce s3c64xx_spi_set_port_id()
spi: s3c64xx: let the SPI core determine the bus number
spi: s3c64xx: allow FIFO depth to be determined from the compatible
spi: s3c64xx: retrieve the FIFO depth from the device tree
spi: s3c64xx: determine the fifo depth only once
spi: s3c64xx: allow full FIFO masks
spi: s3c64xx: define a magic value
spi: dt-bindings: introduce FIFO depth properties
spi: axi-spi-engine: use struct_size() macro
spi: axi-spi-engine: use __counted_by() attribute
spi: axi-spi-engine: remove p from struct spi_engine_message_state
...
Commit e519f0bb64 ("ARM/mmc: Convert old mmci-omap to GPIO descriptors")
moved Nokia N810 MMC power up/down from the board file into the MMC driver.
The change removed some delays, and ordering without a valid reason.
Restore power up/down to match the original code. This matters only on N810
where the 2nd GPIO is in use. Other boards will see an additional delay but
that should be a lesser concern than omitting delays altogether.
Fixes: e519f0bb64 ("ARM/mmc: Convert old mmci-omap to GPIO descriptors")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Message-ID: <20240223181439.1099750-6-aaro.koskinen@iki.fi>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After a deferred probe, GPIO descriptor lookup will fail with EBUSY. Fix by
using managed descriptors.
Fixes: e519f0bb64 ("ARM/mmc: Convert old mmci-omap to GPIO descriptors")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Message-ID: <20240223181439.1099750-5-aaro.koskinen@iki.fi>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The lookup is done before host->dev is initialized. It will always just
fail silently, and the MMC behaviour is totally unpredictable as the switch
is left in an undefined state. Fix that.
Fixes: e519f0bb64 ("ARM/mmc: Convert old mmci-omap to GPIO descriptors")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Message-ID: <20240223181439.1099750-4-aaro.koskinen@iki.fi>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since driver doesn't handle any DMA requests, drop any use of DMA bits,
such as DMA direction. Instead, use MMC_DATA_WRITE flag directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240304184830.1319526-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240304175606.1200076-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parsing dt usually happens very early, sometimes even before the struct
mmc_host has been allocated (e.g. dw_mci_probe() and dw_mci_parse_dt() in
dw_mmc.c). Looking at the source of mmc_of_parse_clk_phase(), it's actually
not needed to have an initialized mmc_host, let's therefore pass a struct
device* to it instead.
Also update the only current user, sdhci-of-aspeed.
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://lore.kernel.org/r/20240229-b4-mmc-hi3798mv200-v7-1-10c03f316285@outlook.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This looks strange to call release_mem_region() in a remove function
without any request_mem_region() in the probe or "struct resource"
somewhere.
So remove the corresponding code.
Fixes: 3a96dff0f8 ("mmc: SD/MMC Host Controller for Wondermedia WM8505/WM8650")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/bb0bb1ed1e18de55e8c0547625bde271e64b8c31.1708983064.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.8-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.9.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the to-be-fixed commit, the reset_work handler cleared 'host->mrq'
outside of the spinlock protected critical section. That leaves a small
race window during execution of 'tmio_mmc_reset()' where the done_work
handler could grab a pointer to the now invalid 'host->mrq'. Both would
use it to call mmc_request_done() causing problems (see link below).
However, 'host->mrq' cannot simply be cleared earlier inside the
critical section. That would allow new mrqs to come in asynchronously
while the actual reset of the controller still needs to be done. So,
like 'tmio_mmc_set_ios()', an ERR_PTR is used to prevent new mrqs from
coming in but still avoiding concurrency between work handlers.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/all/20240220061356.3001761-1-dirk.behme@de.bosch.com/
Fixes: df3ef2d3c9 ("mmc: protect the tmio_mmc driver against a theoretical race")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: stable@vger.kernel.org # 3.0+
Link: https://lore.kernel.org/r/20240305104423.3177-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.8-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.9.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AC5X spec says PHY init complete bit must be polled until zero.
We see cases in which timeout can take longer than the standard
calculation on AC5X, which is expected following the spec comment above.
According to the spec, we must wait as long as it takes for that bit to
toggle on AC5X.
Cap that with 100 delay loops so we won't get stuck forever.
Fixes: 06c8b667ff ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222191714.1216470-3-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Each time SD/mmc phy is initialized, at times, in some of
the attempts, phy fails to completes its initialization
which results into timeout error. Per the HW spec, it is
a pre-requisite to ensure a stable SD clock before a phy
initialization is attempted.
Fixes: 06c8b667ff ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222200930.1277665-1-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The introduction of sg_miter was a bit sloppy as it didn't
exactly mimic the semantics of the old code on multiblock reads
and writes: these like you to:
- Advance to the first sglist entry *before* starting to read
any blocks from the card.
- Advance and check availability of the next entry *right after*
processing one block.
Not checking if we have more sglist entries right after
reading a block will lead to this not being checked until we
return to the callback to read out more blocks, i.e. until the
next interrupt arrives. Since the last block is the last one
(no more data will arrive) there will not be a next interrupt,
and we will be waiting forever resulting in a timeout for
command 18 when reading multiple blocks.
The same bug was fixed also in the writing of multiple blocks.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 27b57277d9 ("mmc: sh_mmcif: Use sg_miter for PIO")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240221-fix-sh-mmcif-v2-2-5e521eb25ae4@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the sglist iterations happen in the *threaded* interrupt handler and
that context is not atomic, so don't request an atomic sglist miter. Using
an atomic miter results in "BUG: scheduling while atomic" splats.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 27b57277d9 ("mmc: sh_mmcif: Use sg_miter for PIO")
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240221-fix-sh-mmcif-v2-1-5e521eb25ae4@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sg_miter used to loop over the returned sglist from a
transfer in the esdhc subdriver for SDHCI can be called
from atomic context so the miter needs to be atomic.
sdhci_request_done() is always called from process context,
either as a work or as part of the threaded interrupt handler,
but the one case when we are actually calling .request_done()
from an atomic context is in sdhci_irq().
Fix this by flagging the miter atomic so we always use
kmap_atomic().
Fixes: e8a167b848 ("mmc: sdhci-esdhc-mcf: Use sg_miter for swapping")
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240228-fix-sdhci-esdhc-mcf-2-v2-1-4ebb3fd691ea@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the mmc controller in the Sophgo CV1800B and SG2002
with corresponding new compatible strings. Implement custom sdhci_ops.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20240217144202.3808-3-jszhang@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 32f18e5961 ("mmc: improve API to make clear hw_reset callback
is for cards") made it clear that the hw_reset callback is intended for
resetting the card. Remove the .card_hw_reset callback from the
meson-mx-sdhc-mmc driver because it's purpose is to reset the SDHC
controller (FIFOs, PHY, DMA interface, ...).
While here also rename and change the argument of meson_mx_sdhc_hw_reset
so it cannot be called by accident as a replacement for card_hw_reset in
the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20240217100200.1494980-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that devm_clk_hw_get_clk() has been available for a while we can
resolve an older TODO where this API did not exist yet. No functional
changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20240217100200.1494980-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.8-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.9.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
DMA-API: mmci-pl18x 48220000.mmc: cacheline tracking EEXIST,
overlapping mappings aren't supported
WARNING: CPU: 1 PID: 51 at kernel/dma/debug.c:568
add_dma_entry+0x234/0x2f4
Modules linked in:
CPU: 1 PID: 51 Comm: kworker/1:2 Not tainted 6.1.28 #1
Hardware name: STMicroelectronics STM32MP257F-EV1 Evaluation Board (DT)
Workqueue: events_freezable mmc_rescan
Call trace:
add_dma_entry+0x234/0x2f4
debug_dma_map_sg+0x198/0x350
__dma_map_sg_attrs+0xa0/0x110
dma_map_sg_attrs+0x10/0x2c
sdmmc_idma_prep_data+0x80/0xc0
mmci_prep_data+0x38/0x84
mmci_start_data+0x108/0x2dc
mmci_request+0xe4/0x190
__mmc_start_request+0x68/0x140
mmc_start_request+0x94/0xc0
mmc_wait_for_req+0x70/0x100
mmc_send_tuning+0x108/0x1ac
sdmmc_execute_tuning+0x14c/0x210
mmc_execute_tuning+0x48/0xec
mmc_sd_init_uhs_card.part.0+0x208/0x464
mmc_sd_init_card+0x318/0x89c
mmc_attach_sd+0xe4/0x180
mmc_rescan+0x244/0x320
DMA API debug brings to light leaking dma-mappings as dma_map_sg and
dma_unmap_sg are not correctly balanced.
If an error occurs in mmci_cmd_irq function, only mmci_dma_error
function is called and as this API is not managed on stm32 variant,
dma_unmap_sg is never called in this error path.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 46b723dd86 ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240207143951.938144-1-christophe.kerello@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use existing typedef for dma_filter_fn to avoid duplicating type
definition.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240208202137.630281-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The variable id is being initialized with a value that is never
read, it is being re-assigned later on. The initialization is
redundant and can be removed.
Cleans up clang scan build warning:
drivers/mmc/host/wbsd.c:1287:4: warning: Value stored to 'id'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240205191310.1848561-1-colin.i.king@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the scatterlist memory iterator instead of just
dereferencing virtual memory using sg_virt().
This make highmem references work properly.
This driver also has a bug in the PIO sglist handling that
is fixed as part of the patch: it does not travers the
list of scatterbuffers: it will just process the first
item in the list. This is fixed by augmenting the logic
such that we do not process more than one sgitem
per IRQ instead of counting down potentially the whole
length of the request.
We can suspect that the PIO path is quite untested.
Suggested-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/linux-mmc/20240122073423.GA25859@lst.de/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240127-mmc-proper-kmap-v2-5-d8e732aa97d1@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The whole scatterlist chain is submitted to the DMA engine,
but the code is written to just account for the length of
the first sg entry.
When the DMA transfer is finished, all the data in the
request has been transferred, account for this instead.
This only works because the moxart_request() function isn't
checking that all data was transferred and will
unconditionally issue mmc_request_done() after returning
successfully from moxart_transfer_dma().
Keep the assignment of accounted bytes in .bytes_xfered
but move it after the completion where we know it has
actually happened.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240127-mmc-proper-kmap-v2-3-d8e732aa97d1@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
some functions and struct members were renamed. To not break all drivers
compatibility macros were provided.
To be able to remove these compatibility macros push the renaming into
this driver.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/a9c95759cf77a19c160d1d497c76ac5770c67684.1707324794.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver shall switch clock source from DLL clock to
OPE clock when power off card to ensure that card
can be identified with OPE clock by BIOS.
Signed-off-by: Fred Ai <fred.ai@bayhubtech.com>
Fixes:4be33cf18703 ("mmc: sdhci-pci-o2micro: Improve card input timing at SDR104/HS200 mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240203102908.4683-1-fredaibayhubtech@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here is the big set of char/misc and other driver subsystem changes for
6.8-rc1. Lots of stuff in here, but first off, you will get a merge
conflict in drivers/android/binder_alloc.c when merging this tree due to
changing coming in through the -mm tree.
The resolution of the merge issue can be found here:
https://lore.kernel.org/r/20231207134213.25631ae9@canb.auug.org.au
or in a simpler patch form in that thread:
https://lore.kernel.org/r/ZXHzooF07LfQQYiE@google.com
If there are issues with the merge of this file, please let me know.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported issues
(other than the binder merge conflict.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeMMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynWNgCfQ/Yz7QO6EMLDwHO5LRsb3YMhjL4AoNVdanjP
YoI7f1I4GBcC0GKNfK6s
=+Kyv
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem changes
for 6.8-rc1.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (341 commits)
android: removed duplicate linux/errno
uio: Fix use-after-free in uio_open
drivers: soc: xilinx: add check for platform
firmware: xilinx: Export function to use in other module
scripts/tags.sh: remove find_sources
scripts/tags.sh: use -n to test archinclude
scripts/tags.sh: add local annotation
scripts/tags.sh: use more portable -path instead of -wholename
scripts/tags.sh: Update comment (addition of gtags)
firmware: zynqmp: Convert to platform remove callback returning void
firmware: turris-mox-rwtm: Convert to platform remove callback returning void
firmware: stratix10-svc: Convert to platform remove callback returning void
firmware: stratix10-rsu: Convert to platform remove callback returning void
firmware: raspberrypi: Convert to platform remove callback returning void
firmware: qemu_fw_cfg: Convert to platform remove callback returning void
firmware: mtk-adsp-ipc: Convert to platform remove callback returning void
firmware: imx-dsp: Convert to platform remove callback returning void
firmware: coreboot_table: Convert to platform remove callback returning void
firmware: arm_scpi: Convert to platform remove callback returning void
firmware: arm_scmi: Convert to platform remove callback returning void
...
- Don't force a retune before eMMC RPMB switch
- Add optional HS400 tuning in HS400es initialization
- Add a sysfs node to for write-protect-group-size
- Add re-tuning test to the mmc-test module
- Use mrq.sbc to support close-ended ioctl requests
MMC host:
- mmci: Add support for SDIO in-band irqs for the stm32 variant
- mmc_spi: Remove broken support custom DMA mapped buffers
- mtk-sd: Improve and extend the support for tunings
- renesas_sdhi: Document support for the RZ/Five variant
- sdhci_am654: Drop support for the ti,otap-del-sel DT property
- sdhci-brcmstb: Add support for the brcm 74165b0 variant
- sdhci-msm: Add compatibles for IPQ4019 and IPQ8074
- sdhci-of-dwcmshc: Add support for the T-Head TH1520 variant
- sdhci-xenon: Add support for the Marvell ac5 variant
-----BEGIN PGP SIGNATURE-----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=+2YX
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Don't force a retune before eMMC RPMB switch
- Add optional HS400 tuning in HS400es initialization
- Add a sysfs node to for write-protect-group-size
- Add re-tuning test to the mmc-test module
- Use mrq.sbc to support close-ended ioctl requests
MMC host:
- mmci: Add support for SDIO in-band irqs for the stm32 variant
- mmc_spi: Remove broken support custom DMA mapped buffers
- mtk-sd: Improve and extend the support for tunings
- renesas_sdhi: Document support for the RZ/Five variant
- sdhci_am654: Drop support for the ti,otap-del-sel DT property
- sdhci-brcmstb: Add support for the brcm 74165b0 variant
- sdhci-msm: Add compatibles for IPQ4019 and IPQ8074
- sdhci-of-dwcmshc: Add support for the T-Head TH1520 variant
- sdhci-xenon: Add support for the Marvell ac5 variant"
* tag 'mmc-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (27 commits)
mmc: xenon: Add ac5 support via bounce buffer
dt-bindings: mmc: add Marvell ac5
mmc: sdhci-brcmstb: add new sdhci reset sequence for brcm 74165b0
dt-bindings: mmc: brcm,sdhci-brcmstb: Add support for 74165b0
mmc: core: Do not force a retune before RPMB switch
mmc: core: Add HS400 tuning in HS400es initialization
mmc: sdhci_omap: Fix TI SoC dependencies
mmc: sdhci_am654: Fix TI SoC dependencies
mmc: core: Add wp_grp_size sysfs node
mmc: mmc_test: Add re-tuning test
mmc: mmc_spi: remove custom DMA mapped buffers
dt-bindings: mmc: sdhci-msm: document dedicated IPQ4019 and IPQ8074
dt-bindings: mmc: synopsys-dw-mshc: add iommus for Intel SocFPGA
mmc: mtk-sd: Extend number of tuning steps
dt-bindings: mmc: mtk-sd: add tuning steps related property
mmc: sdhci-omap: don't misuse kernel-doc marker
mmc: mtk-sd: Increase the verbosity of msdc_track_cmd_data
mmc: core: Use mrq.sbc in close-ended ffu
mmc: sdhci_am654: Drop lookup for deprecated ti,otap-del-sel
mmc: sdhci-of-dwcmshc: Use logical OR instead of bitwise OR in dwcmshc_probe()
...
A moderately busy release for SPI, the main core update was the merging
of support for multiple chip selects, used in some flash configurations.
There were also big overhauls for the AXI SPI Engine and PL022 drivers,
plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with submitting
messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmWbHmMACgkQJNaLcl1U
h9CpSwf+O981469g1twyEpq5PJlNgdXmrKUpezcC18X4DLXmlf5hoCsHUFIU2DuX
oBZuUQVp1KaEzJ4LX1giAOTuhfwPAItGR+/JMs6VxT/V0MMCHaNYcU5zLHXacDFL
URU7hyyhxUp9PzGNI/IEQH2DPv3QVX8Z1CVQQNQpnTsvbpBEF/osxB3SdWg65Y4J
B9nEW5hnyDsjxQVzjwCMFsy1vJeaBkP++zdPhPGE4RaNcweX+hksVRWVJ3DqUuJC
u4IyO5Hmduqmyjyc7MEV6lekecnyHc72WIzFXJpy0FOW0CstOQD59D5Fnbdvbb9i
mm3IJ1Vh/oepZBNPAmHCPqMEAqr5ZQ==
=49Kh
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A moderately busy release for SPI, the main core update was the
merging of support for multiple chip selects, used in some flash
configurations. There were also big overhauls for the AXI SPI Engine
and PL022 drivers, plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with
submitting messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five"
* tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (83 commits)
spi: stm32: add st,stm32mp25-spi compatible supporting STM32MP25 soc
dt-bindings: spi: stm32: add st,stm32mp25-spi compatible
spi: stm32: use dma_get_slave_caps prior to configuring dma channel
spi: axi-spi-engine: fix struct member doc warnings
spi: pl022: update description of internal_cs_control()
spi: pl022: delete description of cur_msg
spi: dw: Remove Intel Thunder Bay SOC support
spi: dw: Remove Intel Thunder Bay SOC support
spi: sh-msiof: Enforce fixed DTDL for R-Car H3
spi: ljca: switch to use devm_spi_alloc_host()
spi: cs42l43: switch to use devm_spi_alloc_host()
spi: zynqmp-gqspi: switch to use modern name
spi: zynq-qspi: switch to use modern name
spi: xtensa-xtfpga: switch to use modern name
spi: xlp: switch to use modern name
spi: xilinx: switch to use modern name
spi: xcomm: switch to use modern name
spi: uniphier: switch to use modern name
spi: topcliff-pch: switch to use modern name
spi: wpcm-fiu: switch to use devm_spi_alloc_host()
...
AC5/X/IM SOCs has a variant of the Xenon eMMC controller,
in which only 31-bit of addressing pass from the controller
on the AXI bus.
Since we cannot guarantee that only buffers from the first 2GB
of memory will reach the driver, the driver is configured for
SDMA mode, without 64-bit mode, overriding the DMA mask to 34-bit
to support the DDR memory mapping, which starts at offset 8GB.
Signed-off-by: Elad Nachman <enachman@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240104173033.2836110-1-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
74165b0 shall use a new sdio controller core version which
requires a different reset sequence. For core reset we use
sdhci_reset. For CMD and/or DATA reset added a new function
to also enable SDHCI clocks SDHCI_CLOCK_CARD_EN
SDHCI_CLOCK_INT_EN along with the SDHCI_RESET_CMD and/or
SDHCI_RESET_DATA fields.
Signed-off-by: Kamal Dasu <kdasu@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240103222338.31447-3-kamal.dasu@broadcom.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.7-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.8.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC devices that do not close the auto clk gate after hw reset will
cause eMMC initialization to fail. Let's fix this.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Fixes: ff874dbc4f ("mmc: sdhci-sprd: Disable CLK_AUTO when the clock is less than 400K")
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231204064934.21236-1-wenchao.chen@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_omap is specific to older TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.
Fixes: 7d326930d3 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20231220135950.433588-2-pbrobinson@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_am654 is specific to recent TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.
Fixes: 41fd4caeb0 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20231220135950.433588-1-pbrobinson@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need to duplicate what SPI core or individual controller
drivers already do, i.e. mapping the buffers for DMA capable transfers.
Note, that the code, besides its redundancy, was buggy: strictly speaking
there is no guarantee, while it's true for those which can use this code
(see below), that the SPI host controller _is_ the device which does DMA.
Also see the Link tags below.
Additional notes. Currently only two SPI host controller drivers may use
premapped (by the user) DMA buffers:
- drivers/spi/spi-au1550.c
- drivers/spi/spi-fsl-spi.c
Both of them have DMA mapping support code. I don't expect that SPI host
controller code is worse than what has been done in mmc_spi. Hence I do
not expect any regressions here. Otherwise, I'm pretty much sure these
regressions have to be fixed in the respective drivers, and not here.
That said, remove all related pieces of DMA mapping code from mmc_spi.
Link: https://lore.kernel.org/linux-mmc/c73b9ba9-1699-2aff-e2fd-b4b4f292a3ca@raspberrypi.org/
Link: https://stackoverflow.com/questions/67620728/mmc-spi-issue-not-able-to-setup-mmc-sd-card-in-linux
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231207221901.3259962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
rts5264 can support sd express card, so add the id in sd express card init
to do rts5264 register setting when the sd express card insert
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20231208032145.2143580-4-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, during the MSDC calibration process, a full clock cycle
actually not be covered, which in some cases didn't yield the best
results and could cause CRC errors. This problem is particularly
evident when MSDC is used as an SDIO host. In fact, MSDC support
tuning up to a maximum of 64 steps, but by default, the step number
is 32. By increase the tuning step, we are more likely to cover more
parts of a clock cycle, and get better calibration result.
To illustrate, when tuning 32 steps, if the obtained window has a hole
near the middle, like this: 0xffc07ff (hex), then the selected delay
will be the 6 (counting from right to left).
(32 <- 1)
1111 1111 1100 0000 0000 0111 11(1)1 1111
However, if we tune 64 steps, the window obtained may look like this:
0xfffffffffffc07ff. The final selected delay will be 44, which is
safer as it is further away from the hole:
(64 <- 1)
1111 ... (1)111 1111 1111 1111 1111 1100 0000 0000 0111 1111 1111
In this case, delay 6 selected through 32 steps tuning is obviously
not optimal, and this delay is closer to the hole, using it would
easily cause CRC problems.
As per mesaurements taken on mediatek SoC platform, the tuning phase
will take:
eMMC - 32 steps: ~3ms
- 64 steps: ~6ms
SDIO - 32 steps: ~4ms
- 64 steos: ~7ms
Tuning more steps won't prolong boot times by any meaningful amount
of time, so for SD/SDIO the default tuning steps will be adjust to
64. But for eMMC, it is still preferred to use 32 steps tuning as
otherwise there would be performance lose when accessing the RPMB
partition(requiring retuning each time).
You can configure property "mediatek,tuning-step" in MSDC dts node
to adjust the step number.
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231207063535.29546-3-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use "/*" instead of "/**" for common C comments to prevent warnings
from scripts/kernel-doc.
sdhci-omap.c:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
sdhci-omap.c:3: warning: missing initial short description on line:
* SDHCI Controller driver for TI's OMAP SoCs
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202311201117.lFxgJTK6-lkp@intel.com/
Link: https://lore.kernel.org/r/20231206055855.21092-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.7-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.8.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This log message is necessary for debugging, so enable it by default to
debug issues that are hard to reproduce locally.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231201102747.3854573-1-treapking@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ti,otap-del-sel has been deprecated since v5.7 and there are no users of
this property and no documentation in the DT bindings either.
Drop the fallback code looking for this property, this makes
sdhci_am654_get_otap_delay() much easier to read as all the TAP values
can be handled via a single iterator loop.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231122060215.2074799-1-vigneshr@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns (or errors with CONFIG_WERROR=y):
drivers/mmc/host/sdhci-of-dwcmshc.c:873:7: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
873 | if ((device_property_read_bool(dev, "mmc-ddr-1_8v")) |
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
874 | (device_property_read_bool(dev, "mmc-hs200-1_8v")) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| ||
875 | (device_property_read_bool(dev, "mmc-hs400-1_8v")))
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/sdhci-of-dwcmshc.c:873:7: note: cast one or both operands to int to silence this warning
drivers/mmc/host/sdhci-of-dwcmshc.c:873:7: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
873 | if ((device_property_read_bool(dev, "mmc-ddr-1_8v")) |
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| ||
874 | (device_property_read_bool(dev, "mmc-hs200-1_8v")) |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/sdhci-of-dwcmshc.c:873:7: note: cast one or both operands to int to silence this warning
2 errors generated.
There is little reason for this if statement to use bitwise ORs, as the
short circuiting of logical OR does not need to be avoided in this
context; it would be wasteful to call device_property_read_bool() three
times if the first two calls returned true. Switch to logical OR to fix
the warning.
While in the area, the parentheses around the calls to
device_property_read_bool() are not necessary and make the if statement
harder to read, so remove them.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1960
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Drew Fustini <dfustini@baylibre.com>
Link: https://lore.kernel.org/r/20231116-sdhci-of-dwcmshc-fix-wbitwise-instead-of-logical-v1-1-7e1a7f4ccaab@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the mmc controller in the T-Head TH1520 with the new
compatible "thead,th1520-dwcmshc". Implement custom sdhci_ops for
set_uhs_signaling, reset, voltage_switch, and platform_execute_tuning.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Link: https://lore.kernel.org/r/20231109-th1520-mmc-v5-3-018bd039cf17@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Expose __sdhci_execute_tuning() so that it can be called from the
mmc host controller drivers.
In the sdhci-of-dwcmshc driver, sdhci_dwcmshc_th1520_ops sets
platform_execute_tuning to th1520_execute_tuning(). That function has
to manipulate phy registers before tuning can be performed. To avoid
copying the code verbatim from __sdhci_execute_tuning() into
th1520_execute_tuning(), make it possible for __sdhci_execute_tuning()
to be called from sdhci-of-dwcmshc.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Link: https://lore.kernel.org/r/20231109-th1520-mmc-v5-2-018bd039cf17@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the support of SDIO in-band interrupt mode for STM32 and Ux500
variants.
It allows the SD I/O card to interrupt the host on SDMMC_D1 data line.
It is not enabled by default on Ux500 variant as this is unstable and
Ux500 users should use out-of-band IRQs.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231108141637.119497-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 4bc31edebd ("mmc: core: Set HS clock speed before sending
HS CMD13") set HS clock (52MHz) before switching to HS mode. For this
freq, FCLK_DIV5 will be selected and div value is 10 (reg value is 9).
Then we set rx_clk_phase to 11 or 15 which is out of range and make
hardware frozen. After we send command request, no irq will be
interrupted and the mmc driver will keep to wait for request finished,
even durning rebooting.
So let's set it to Phase 90 which should work in most cases. Then let
meson_mx_sdhc_execute_tuning() to find the accurate value for data
transfer.
If this doesn't work, maybe need to define a factor in dts.
Fixes: e4bf1b0970 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/TYZPR01MB5556A3E71554A2EC08597EA4C9CDA@TYZPR01MB5556.apcprd01.prod.exchangelabs.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To address IO performance commit f9e5b33934
("mmc: host: Improve I/O read/write performance for GL9763E")
limited LPM negotiation to runtime suspend state.
The problem is that it only flips the switch in the runtime PM
resume/suspend logic.
Disable LPM negotiation in gl9763e_add_host.
This helps in two ways:
1. It was found that the LPM switch stays in the same position after
warm reboot. Having it set in init helps with consistency.
2. Disabling LPM during the first runtime resume leaves us susceptible
to the performance issue in the time window between boot and the
first runtime suspend.
Fixes: f9e5b33934 ("mmc: host: Improve I/O read/write performance for GL9763E")
Cc: stable@vger.kernel.org
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Reviewed-by: Sven van Ashbrook <svenva@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231114115516.1585361-1-korneld@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SPI_MASTER_HALF_DUPLEX is the legacy name of a definition
for a half duplex flag. Since all others had been replaced with
the respective SPI_CONTROLLER prefix get rid of the last one
as well. There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20231113111249.3982461-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a task completion notification (TCN) is received when there is no
outstanding task, the cqhci driver issues a "spurious TCN" warning. This
was observed to happen right after CQE error recovery.
When an error interrupt is received the driver runs recovery logic.
It halts the controller, clears all pending tasks, and then re-enables
it. On some platforms, like Intel Jasper Lake, a stale task completion
event was observed, regardless of the CQHCI_CLEAR_ALL_TASKS bit being set.
This results in either:
a) Spurious TC completion event for an empty slot.
b) Corrupted data being passed up the stack, as a result of premature
completion for a newly added task.
Rather than add a quirk for affected controllers, ensure tasks are cleared
by toggling CQHCI_ENABLE, which would happen anyway if
cqhci_clear_all_tasks() timed out. This is simpler and should be safe and
effective for all controllers.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Reported-by: Kornel Dulęba <korneld@chromium.org>
Tested-by: Kornel Dulęba <korneld@chromium.org>
Co-developed-by: Kornel Dulęba <korneld@chromium.org>
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-7-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A correctly operating controller should successfully halt and clear tasks.
Failure may result in errors elsewhere, so promote messages from debug to
warnings.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Failing to halt complicates the recovery. Additionally, unless the card or
controller are stuck, which is expected to be very rare, then the halt
should succeed, so it is better to wait. Set a large timeout.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to a flaw in the hardware design, the GL9750 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9750
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: d7133797e9 ("mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2")
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231107095741.8832-2-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to a flaw in the hardware design, the GL9755 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9755
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: 36ed2fd32b ("mmc: sdhci-pci-gli: A workaround to allow GL9755 to enter ASPM L1.2")
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231107095741.8832-3-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ti,otap-del-sel-legacy/ti,itap-del-sel-legacy passed from DT
are currently ignored for all SD/MMC and eMMC modes. Fix this
by making start loop index to MMC_TIMING_LEGACY.
Fixes: 8ee5fc0e0b ("mmc: sdhci_am654: Update OTAPDLY writes")
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231026061458.1116276-1-n-yadav@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.6-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.7.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the t7 and older SoC families, the CMD_CFG_ERROR has no effect.
Starting from SoC family C3, setting this bit without SG LINK data
address will cause the controller to generate an IRQ and stop working.
To fix it, don't set the bit CMD_CFG_ERROR anymore.
Fixes: 18f92bc02f ("mmc: meson-gx: make sure the descriptor is stopped on errors")
Signed-off-by: Rong Chen <rong.chen@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231026073156.2868310-1-rong.chen@amlogic.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20231006224343.441720-1-robh@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The devm_platform_ioremap_resource() and platform_get_irq() print
the error messages themselves and our "failed" one brings no value
and just noise. Refactor code to avoid those noisy error messages.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231006105803.3374241-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The acpi_evaluate_dsm_typed() provides a way to check the type of the
object evaluated by _DSM call. Use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231002135103.2602847-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STM32 SDMMC peripheral (at least for the STM32F429, STM32F469 and
STM32F746, which are all the currently supported devices using periphid
0x00880180) requires DMA to be performed in peripheral flow controller
mode. From the STM32F74/5 reference manual, section 35.3.2:
"SDMMC host allows only to use the DMA in peripheral flow controller
mode. DMA stream used to serve SDMMC must be configured in peripheral
flow controller mode"
This patch adds a variant option to control peripheral flow control and
enables it for the STM32 variant.
Signed-off-by: Ben Wolsieffer <Ben.Wolsieffer@hefring.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230928135644.1489691-1-ben.wolsieffer@hefring.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.6-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.7.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before, we used syscon to achieve tuning, but the actual measurement
showed little effect, so the tuning implementation was modified here,
and it was realized by reading and writing the UHS_REG_EXT register.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Link: https://lore.kernel.org/r/20230922062834.39212-3-william.qiu@starfivetech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By dynamically adjusting the host->hsq_depth, based upon the buffer size
being 4k and that we get at least two I/O write requests in flight, we can
improve the throughput a bit. This is typical for a random I/O write
pattern.
More precisely, by dynamically changing the number of requests in flight
from 2 to 5, we can on some platforms observe ~4-5% increase in throughput.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Link: https://lore.kernel.org/r/20230919074707.25517-3-wenchao.chen@unisoc.com
[Ulf: Re-wrote the commitmsg, minor adjustment to the code - all to clarify.]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow dynamical updates of the current number of used in-flight
requests, let's move away from using a hard-coded value to a use a
corresponding variable in the struct mmc_host.
This can be valuable when optimizing for certain I/O request sequences, as
shown by subsequent changes.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Link: https://lore.kernel.org/r/20230919074707.25517-2-wenchao.chen@unisoc.com
[Ulf: Re-wrote the commitmsg to clarify the change]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When GL9750 enters ASPM L1 sub-states, it will stay at L1.1 and will not
enter L1.2. The workaround is to toggle PM state to allow GL9750 to enter
ASPM L1.2.
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20230912091710.7797-1-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for_each_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20230907095521.14053-6-Julia.Lawall@inria.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_SDHI_INTERNAL_DMAC config option has dependency on ARM64 and
R7S9210/R8A77470 this dependency will keep growing for future SoCs for
varying architectures. So to simplify this configuration make
MMC_SDHI_INTERNAL_DMAC solely depend on ARCH_RENESAS, as all Renesas
SoCs inherently depend on the ARCH_RENESAS config option.
This allows selecting MMC_SDHI_INTERNAL_DMAC config option for RZ/Five SoC
which is based on RISC-V architecture.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20230901122701.318082-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current manual tuning logic only get the first pass window, but
this pass window maybe not the best pass window.
Now find all the pass window, and chose the largest pass window,
and use the average value of this largest pass window to get the
best timing.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230831032647.3128702-1-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To improve the r/w performance of GL9763E, the current driver inhibits LPM
negotiation while the device is active.
This prevents a large number of SoCs from suspending, notably x86 systems
which commonly use S0ix as the suspend mechanism - for example, Intel
Alder Lake and Raptor Lake processors.
Failure description:
1. Userspace initiates s2idle suspend (e.g. via writing to
/sys/power/state)
2. This switches the runtime_pm device state to active, which disables
LPM negotiation, then calls the "regular" suspend callback
3. With LPM negotiation disabled, the bus cannot enter low-power state
4. On a large number of SoCs, if the bus not in a low-power state, S0ix
cannot be entered, which in turn prevents the SoC from entering
suspend.
Fix by re-enabling LPM negotiation in the device's suspend callback.
Suggested-by: Stanislaw Kardach <skardach@google.com>
Fixes: f9e5b33934 ("mmc: host: Improve I/O read/write performance for GL9763E")
Cc: stable@vger.kernel.org
Signed-off-by: Sven van Ashbrook <svenva@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230831160055.v3.1.I7ed1ca09797be2dd76ca914c57d88b32d24dac88@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Summary of the changes worth highlighting from most interesting to boring below:
* Christoph Hellwig's symbol_get() fix to Nvidia's efforts to circumvent the
protection he put in place in year 2020 to prevent proprietary modules from
using GPL only symbols, and also ensuring proprietary modules which export
symbols grandfather their taint. That was done through year 2020 commit
262e6ae708 ("modules: inherit TAINT_PROPRIETARY_MODULE"). Christoph's new
fix is done by clarifing __symbol_get() was only ever intended to prevent
module reference loops by Linux kernel modules and so making it only find
symbols exported via EXPORT_SYMBOL_GPL(). The circumvention tactic used
by Nvidia was to use symbol_get() to purposely swift through proprietary
module symbols and completley bypass our traditional EXPORT_SYMBOL*()
annotations and community agreed upon restrictions.
A small set of preamble patches fix up a few symbols which just needed
adjusting for this on two modules, the rtc ds1685 and the networking enetc
module. Two other modules just needed some build fixing and removal of use
of __symbol_get() as they can't ever be modular, as was done by Arnd on
the ARM pxa module and Christoph did on the mmc au1xmmc driver.
This is a good reminder to us that symbol_get() is just a hack to address
things which should be fixed through Kconfig at build time as was done in
the later patches, and so ultimately it should just go.
* Extremely late minor fix for old module layout 055f23b74b ("module: check
for exit sections in layout_sections() instead of module_init_section()") by
James Morse for arm64. Note that this layout thing is old, it is *not*
Song Liu's commit ac3b432839 ("module: replace module_layout with
module_memory"). The issue however is very odd to run into and so there was
no hurry to get this in fast.
* Although the fix did not go through the modules tree I'd like to highlight
the fix by Peter Zijlstra in commit 5409730962 ("x86/static_call: Fix
__static_call_fixup()") now merged in your tree which came out of what
was originally suspected to be a fallout of the the newer module layout
changes by Song Liu commit ac3b432839 ("module: replace module_layout
with module_memory") instead of module_init_section()"). Thanks to the report
by Christian Bricart and the debugging by Song Liu & Peter that turned to
be noted as a kernel regression in place since v5.19 through commit
ee88d363d1 ("x86,static_call: Use alternative RET encoding").
I highlight this to reflect and clarify that we haven't seen more fallout
from ac3b432839 ("module: replace module_layout with module_memory").
* RISC-V toolchain got mapping symbol support which prefix symbols with "$"
to help with alignment considerations for disassembly. This is used to
differentiate between incompatible instruction encodings when disassembling.
RISC-V just matches what ARM/AARCH64 did for alignment considerations and
Palmer Dabbelt extended is_mapping_symbol() to accept these symbols for
RISC-V. We already had support for this for all architectures but it also
checked for the second character, the RISC-V check Dabbelt added was just
for the "$". After a bit of testing and fallout on linux-next and based on
feedback from Masahiro Yamada it was decided to simplify the check and treat
the first char "$" as unique for all architectures, and so we no make
is_mapping_symbol() for all archs if the symbol starts with "$".
The most relevant commit for this for RISC-V on binutils was:
https://sourceware.org/pipermail/binutils/2021-July/117350.html
* A late fix by Andrea Righi (today) to make module zstd decompression use
vmalloc() instead of kmalloc() to account for large compressed modules. I
suspect we'll see similar things for other decompression algorithms soon.
* samples/hw_breakpoint minor fixes by Rong Tao, Arnd Bergmann and Chen Jiahao
-----BEGIN PGP SIGNATURE-----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=IQy2
-----END PGP SIGNATURE-----
Merge tag 'modules-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull modules updates from Luis Chamberlain:
"Summary of the changes worth highlighting from most interesting to
boring below:
- Christoph Hellwig's symbol_get() fix to Nvidia's efforts to
circumvent the protection he put in place in year 2020 to prevent
proprietary modules from using GPL only symbols, and also ensuring
proprietary modules which export symbols grandfather their taint.
That was done through year 2020 commit 262e6ae708 ("modules:
inherit TAINT_PROPRIETARY_MODULE"). Christoph's new fix is done by
clarifing __symbol_get() was only ever intended to prevent module
reference loops by Linux kernel modules and so making it only find
symbols exported via EXPORT_SYMBOL_GPL(). The circumvention tactic
used by Nvidia was to use symbol_get() to purposely swift through
proprietary module symbols and completely bypass our traditional
EXPORT_SYMBOL*() annotations and community agreed upon
restrictions.
A small set of preamble patches fix up a few symbols which just
needed adjusting for this on two modules, the rtc ds1685 and the
networking enetc module. Two other modules just needed some build
fixing and removal of use of __symbol_get() as they can't ever be
modular, as was done by Arnd on the ARM pxa module and Christoph
did on the mmc au1xmmc driver.
This is a good reminder to us that symbol_get() is just a hack to
address things which should be fixed through Kconfig at build time
as was done in the later patches, and so ultimately it should just
go.
- Extremely late minor fix for old module layout 055f23b74b
("module: check for exit sections in layout_sections() instead of
module_init_section()") by James Morse for arm64. Note that this
layout thing is old, it is *not* Song Liu's commit ac3b432839
("module: replace module_layout with module_memory"). The issue
however is very odd to run into and so there was no hurry to get
this in fast.
- Although the fix did not go through the modules tree I'd like to
highlight the fix by Peter Zijlstra in commit 5409730962
("x86/static_call: Fix __static_call_fixup()") now merged in your
tree which came out of what was originally suspected to be a
fallout of the the newer module layout changes by Song Liu commit
ac3b432839 ("module: replace module_layout with module_memory")
instead of module_init_section()"). Thanks to the report by
Christian Bricart and the debugging by Song Liu & Peter that turned
to be noted as a kernel regression in place since v5.19 through
commit ee88d363d1 ("x86,static_call: Use alternative RET
encoding").
I highlight this to reflect and clarify that we haven't seen more
fallout from ac3b432839 ("module: replace module_layout with
module_memory").
- RISC-V toolchain got mapping symbol support which prefix symbols
with "$" to help with alignment considerations for disassembly.
This is used to differentiate between incompatible instruction
encodings when disassembling. RISC-V just matches what ARM/AARCH64
did for alignment considerations and Palmer Dabbelt extended
is_mapping_symbol() to accept these symbols for RISC-V. We already
had support for this for all architectures but it also checked for
the second character, the RISC-V check Dabbelt added was just for
the "$". After a bit of testing and fallout on linux-next and based
on feedback from Masahiro Yamada it was decided to simplify the
check and treat the first char "$" as unique for all architectures,
and so we no make is_mapping_symbol() for all archs if the symbol
starts with "$".
The most relevant commit for this for RISC-V on binutils was:
https://sourceware.org/pipermail/binutils/2021-July/117350.html
- A late fix by Andrea Righi (today) to make module zstd
decompression use vmalloc() instead of kmalloc() to account for
large compressed modules. I suspect we'll see similar things for
other decompression algorithms soon.
- samples/hw_breakpoint minor fixes by Rong Tao, Arnd Bergmann and
Chen Jiahao"
* tag 'modules-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
module/decompress: use vmalloc() for zstd decompression workspace
kallsyms: Add more debug output for selftest
ARM: module: Use module_init_layout_section() to spot init sections
arm64: module: Use module_init_layout_section() to spot init sections
module: Expose module_init_layout_section()
modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules
rtc: ds1685: use EXPORT_SYMBOL_GPL for ds1685_rtc_poweroff
net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_index
mmc: au1xmmc: force non-modular build and remove symbol_get usage
ARM: pxa: remove use of symbol_get()
samples/hw_breakpoint: mark sample_hbp as static
samples/hw_breakpoint: fix building without module unloading
samples/hw_breakpoint: Fix kernel BUG 'invalid opcode: 0000'
modpost, kallsyms: Treat add '$'-prefixed symbols as mapping symbols
kernel: params: Remove unnecessary ‘0’ values from err
module: Ignore RISC-V mapping symbols too
The polarity of the card detection gpio is handled by the "cd-inverted"
property in the device tree. Move this inversion logic to gpiolib to avoid
reading the gpio raw value.
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230825095157.76073-4-balamanikandan.gunasundar@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the contents of linux/atmel-mci.h into
drivers/mmc/host/atmel-mci.c as it is only used in one file
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20230825095157.76073-3-balamanikandan.gunasundar@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace the legacy GPIO APIs with gpio descriptor consumer interface.
To maintain backward compatibility, we rely on the "cd-inverted"
property to manage the invertion flag instead of GPIO property.
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230825095157.76073-2-balamanikandan.gunasundar@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
First of all, Unisoc's IC provides cmd delay and read delay to ensure
that the host can get the correct data. However, according to SD Spec,
there is no need to do tuning in high speed mode, but with the
development of chip processes, it is more and more difficult to find
a suitable delay to cover all the chips. Therefore, we need SD high
speed mode online tuning.
In addition, we added mmc_sd_switch() and mmc_send_status() to the
header file to allow it to be usable by the driver.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Link: https://lore.kernel.org/r/20230825091743.15613-3-wenchao.chen@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit implements the runtime PM operations to disable eMMC card clock
when idle.
Reviewed-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Liming Sun <limings@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230822195929.168552-2-limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit adds handling in dwcmshc_resume() for different error
cases.
Signed-off-by: Liming Sun <limings@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230822195929.168552-1-limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata ERR010450 only shows up if voltage is 1.8V, but if the device is
supplied by 3v3 the errata can be ignored. So let's check for if quirk
SDHCI_QUIRK2_NO_1_8_V is defined or not before limiting the frequency.
Cc: Jim Reinhart <jimr@tekvox.com>
Cc: James Autry <jautry@tekvox.com>
Cc: Matthew Maron <matthewm@tekvox.com>
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230811214853.8623-1-giulio.benetti@benettiengineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_pltfm_unregister() has been removed, rename
sdhci_pltfm_register() to sdhci_pltfm_init_and_add_host() to better
reflect what it does.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-17-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_pltfm_unregister() is unused, remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-16-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-15-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-14-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-13-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-12-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-11-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-10-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-9-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-8-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-7-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_optional_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add sdhci_pltfm_remove() to replace sdhci_pltfm_unregister().
The difference is that sdhci_pltfm_remove() does not do:
clk_disable_unprepare(pltfm_host->clk);
which allows drivers to choose to use devm_clk_get_enabled() or
similar, for pltfm_host->clk.
Once all drivers using sdhci_pltfm_unregister() have been amended to use
sdhci_pltfm_remove() instead, sdhci_pltfm_unregister() will be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-61-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.5-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.6.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-60-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Returning an error code in a platform driver's remove function is wrong
most of the time and there is an effort to make the callback return
void. To prepare this rework the function not to exit early.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-59-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-58-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> # Broadcom
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-57-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230727070051.17778-56-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-52-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-51-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-50-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-49-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-48-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-47-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-46-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://lore.kernel.org/r/20230727070051.17778-45-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Link: https://lore.kernel.org/r/20230727070051.17778-44-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-43-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-42-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230727070051.17778-41-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-40-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-39-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-38-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230727070051.17778-37-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
