There exists several examples today of devices that embed an ethernet
PHY or PCS directly inside an SoC. In this situation, either the device
is controlled through a vendor-specific register set, or sometimes
exposes the standard 802.3 registers that are typically accessed over
MDIO.
As phylib and phylink are designed to use mdiodevices, this driver
allows creating a virtual MDIO bus, that translates mdiodev register
accesses to regmap accesses.
The reason we use regmap is because there are at least 3 such devices
known today, 2 of them are Altera TSE PCS's, memory-mapped, exposed
with a 4-byte stride in stmmac's dwmac-socfpga variant, and a 2-byte
stride in altera-tse. The other one (nxp,sja1110-base-tx-mdio) is
exposed over SPI.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 87e3bee0f2 ("net: mdio: i2c: Separate C22 and C45 transactions")
separated the non-rollball bus accessors, but left the rollball
accessors as is. As rollball accessors are clause 45, this results
in the rollball protocol being completely non-functional. Fix this.
Fixes: 87e3bee0f2 ("net: mdio: i2c: Separate C22 and C45 transactions")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should of_mdiobus_register() fail, a previous usb_get_dev() call should be
undone as in the .disconnect function.
Fixes: 04e37d92fb ("net: phy: add marvell usb to mdio controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of MDIO drivers make use of devm_mdiobus_alloc_size(). This
is only available when CONFIG_MDIO_DEVRES is enabled. Add missing
depends or selects, depending on if there are circular dependencies or
not. This avoids linker errors, especially for randconfig builds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230409150204.2346231-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In device_for_each_child_node(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bus ownership is wrong when using acpi_mdiobus_register() to register an
mdio bus. That function is not inline, so when it calls
mdiobus_register() the wrong THIS_MODULE value is captured.
CC: Maxime Bizon <mbizon@freebox.fr>
Fixes: 803ca24d2f ("net: mdio: Add ACPI support code for mdio")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bus ownership is wrong when using of_mdiobus_register() to register an mdio
bus. That function is not inline, so when it calls mdiobus_register() the wrong
THIS_MODULE value is captured.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
[florian: fix kdoc, added Fixes tag]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230310144716.1544083-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During the refactoring in the commit below, vsc9953_mdio_read() was
replaced with mscc_miim_read(), which has one extra step: it checks for
the MSCC_MIIM_DATA_ERROR bits before returning the result.
On T1040RDB, there are 8 QSGMII PCSes belonging to the switch, and they
are organized in 2 groups. First group responds to MDIO addresses 4-7
because QSGMIIACR1[MDEV_PORT] is 1, and the second group responds to
MDIO addresses 8-11 because QSGMIIBCR1[MDEV_PORT] is 2. I have double
checked that these values are correctly set in the SERDES, as well as
PCCR1[QSGMA_CFG] and PCCR1[QSGMB_CFG] are both 0b01.
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 4 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 4 reg 0x5 MIIM_DATA 0x3da01, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
As can be seen, the data in MIIM_DATA is still valid despite having the
MSCC_MIIM_DATA_ERROR bits set. The driver as introduced in commit
84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953
switch") was ignoring these bits, perhaps deliberately (although
unbeknownst to me).
This is an old IP and the hardware team cannot seem to be able to help
me track down a plausible reason for these failures. I'll keep
investigating, but in the meantime, this is a direct regression which
must be restored to a working state.
The only thing I can do is keep ignoring the errors as before.
Fixes: b996584523 ("net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the mdio mux and internal phy glue of the GXL SoC
family
Reported-by: Da Xue <da@lessconfused.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By using __clk_is_enabled () we can avoid defining an own variable for
tracking whether enable counter is zero.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Force the internal PHY off then on when switching to the internal path.
This fixes problems where the PHY ID is not properly set.
Fixes: 7090425104 ("net: phy: add amlogic g12a mdio mux support")
Suggested-by: Qi Duan <qi.duan@amlogic.com>
Co-developed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230124101157.232234-1-jbrunet@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use devm_clk_get_enabled() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded fwnode_device_is_compatible() in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO core should not pass a C45 request via the C22 API call any
more. So remove the tests from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Deciding if to probe of PHYs using C45 is now determine by if the bus
provides the C45 read method. This makes probe_capabilities redundant
so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The recent refactoring to split C22 and C45 introduced two unneeded
semiconons which the kernel test bot reported. Remove them.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 93641ecbaa ("net: mdio: cavium: Separate C22 and C45 transactions")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230115164203.510615-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ipq4019 driver can perform both C22 and C45 transfers. Create
separate functions for each and register the C45 versions using the
new driver API calls.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The aspeed MDIO bus driver can perform both C22 and C45 transfers.
Modify the existing C45 functions to take the devad as a parameter,
and remove the wrappers so there are individual C22 and C45 functions. Add
the C45 functions to the new API calls.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDIO mux broadcom iproc can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDIO over I2C bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cavium IP can perform both C22 and C45 transfers. Create separate
functions for each and register the C45 versions in both the octeon
and thunder bus driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bitbbanging bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new driver API calls.
The SH Ethernet driver places wrappers around these functions. In
order to not break boards which might be using C45, add similar
wrappers for C45 operations.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is warning report about of_node refcount leak
while probing mdio device:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /spi/soc@0/mdio@710700c0/ethernet@4
In of_mdiobus_register_device(), we increase fwnode refcount
by fwnode_handle_get() before associating the of_node with
mdio device, but it has never been decreased in normal path.
Since that, in mdio_device_release(), it needs to call
fwnode_handle_put() in addition instead of calling kfree()
directly.
After above, just calling mdio_device_free() in the error handle
path of of_mdiobus_register_device() is enough to keep the
refcount balanced.
Fixes: a9049e0c51 ("mdio: Add support for mdio drivers.")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221203073441.3885317-1-zengheng4@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If phy_device_register() or fwnode_mdiobus_phy_device_register()
fail, phy_device_free() is called, the device refcount is decreased
to 0, then fwnode_handle_put() will be called in phy_device_release(),
but in the error path, fwnode_handle_put() has already been called,
so set fwnode to NULL after fwnode_handle_put() in the error path to
avoid double put.
Fixes: cdde156011 ("net: mdiobus: fix unbalanced node reference count")
Reported-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got the following report while doing device(mscc-miim) load test
with CONFIG_OF_UNITTEST and CONFIG_OF_DYNAMIC enabled:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /spi/soc@0/mdio@7107009c/ethernet-phy@0
If the 'fwnode' is not an acpi node, the refcount is get in
fwnode_mdiobus_phy_device_register(), but it has never been
put when the device is freed in the normal path. So call
fwnode_handle_put() in phy_device_release() to avoid leak.
If it's an acpi node, it has never been get, but it's put
in the error path, so call fwnode_handle_get() before
phy_device_register() to keep get/put operation balanced.
Fixes: bc1bee3b87 ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221124150130.609420-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some PHYs can be linked with PSE (Power Sourcing Equipment), so search
for related nodes and attach it to the phydev.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rework error handling as preparation for PSE patch. This patch should
make it easier to extend this function.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some multigig SFPs from RollBall and Hilink do not expose functional
MDIO access to the internal PHY of the SFP via I2C address 0x56
(although there seems to be read-only clause 22 access on this address).
Instead these SFPs PHY can be accessed via I2C via the SFP Enhanced
Digital Diagnostic Interface - I2C address 0x51. The SFP_PAGE has to be
selected to 3 and the password must be filled with 0xff bytes for this
PHY communication to work.
This extends the mdio-i2c driver to support this protocol by adding a
special parameter to mdio_i2c_alloc function via which this RollBall
protocol can be selected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220915065043.665138-3-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220915065043.665138-2-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220915065043.665138-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In of_mdiobus_register(), we should call of_node_put() for 'child'
escaped out of for_each_available_child_of_node().
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Co-developed-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220913125659.3331969-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=HdIo
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-net-pinctrl-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Lee Jones says:
====================
Immutable branch between MFD, Net and Pinctrl due for the v6.0 merge window
* tag 'ib-mfd-net-pinctrl-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: ocelot: Add support for the vsc7512 chip via spi
dt-bindings: mfd: ocelot: Add bindings for VSC7512
resource: add define macro for register address resources
pinctrl: microchip-sgpio: add ability to be used in a non-mmio configuration
pinctrl: microchip-sgpio: allow sgpio driver to be used as a module
pinctrl: ocelot: add ability to be used in a non-mmio configuration
net: mdio: mscc-miim: add ability to be used in a non-mmio configuration
mfd: ocelot: Add helper to get regmap from a resource
====================
Link: https://lore.kernel.org/r/YxrjyHcceLOFlT/c@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few Ocelot chips that contain the logic for this bus, but are
controlled externally. Specifically the VSC7511, 7512, 7513, and 7514. In
the externally controlled configurations these registers are not
memory-mapped.
Add support for these non-memory-mapped configurations.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220905162132.2943088-3-colin.foster@in-advantage.com
This reverts commit f8217275b5.
There are a few more issues to fix that have been reported in the thread
for the original series [1]. We'll need to fix those before this will work.
So, revert it for now.
[1] - https://lore.kernel.org/lkml/CAMuHMdWo_wRwV-i_iyTxVnEsf3Th9GBAG+wxUQMQGnw1t2ijTg@mail.gmail.com/
Fixes: f8217275b5 ("net: mdio: Delete usage of driver_deferred_probe_check_state()")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220819221616.2107893-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that fw_devlink=on by default and fw_devlink supports interrupt
properties, the execution will never get to the point where
driver_deferred_probe_check_state() is called before the supplier has
probed successfully or before deferred probe timeout has expired.
So, delete the call and replace it with -ENODEV.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220601070707.3946847-4-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error values inside the probe function must be < 0. The ENOMEM return
value has the wrong sign: it is positive instead of negative.
Add a minus sign.
Fixes: e239756717 ("net: mdio: Add BCM6368 MDIO mux bus controller")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220428211931.8130-1-dossche.niels@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reset assertion/deassertion for Aspeed MDIO. There are 4 MDIO
controllers embedded in Aspeed AST2600 SOC and share one reset control
register SCU50[3]. To work with old DT blobs which don't have the reset
property, devm_reset_control_get_optional_shared is used in this change.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Create a local device *dev in order to not dereference the platform_device
several times throughout the probe function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a driver for an interrupt controller is missing, of_irq_get()
returns -EPROBE_DEFER ad infinitum, causing
fwnode_mdiobus_phy_device_register(), and ultimately, the entire
of_mdiobus_register() call, to fail. In turn, any phy_connect() call
towards a PHY on this MDIO bus will also fail.
This is not what is expected to happen, because the PHY library falls
back to poll mode when of_irq_get() returns a hard error code, and the
MDIO bus, PHY and attached Ethernet controller work fine, albeit
suboptimally, when the PHY library polls for link status. However,
-EPROBE_DEFER has special handling given the assumption that at some
point probe deferral will stop, and the driver for the supplier will
kick in and create the IRQ domain.
Reasons for which the interrupt controller may be missing:
- It is not yet written. This may happen if a more recent DT blob (with
an interrupt-parent for the PHY) is used to boot an old kernel where
the driver didn't exist, and that kernel worked with the
vintage-correct DT blob using poll mode.
- It is compiled out. Behavior is the same as above.
- It is compiled as a module. The kernel will wait for a number of
seconds specified in the "deferred_probe_timeout" boot parameter for
user space to load the required module. The current default is 0,
which times out at the end of initcalls. It is possible that this
might cause regressions unless users adjust this boot parameter.
The proposed solution is to use the driver_deferred_probe_check_state()
helper function provided by the driver core, which gives up after some
-EPROBE_DEFER attempts, taking "deferred_probe_timeout" into consideration.
The return code is changed from -EPROBE_DEFER into -ENODEV or
-ETIMEDOUT, depending on whether the kernel is compiled with support for
modules or not.
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220407165538.4084809-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add Clause 45 support for Aspeed mdio driver.
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add following additional functions to move out the implementation from
aspeed_mdio_read() and aspeed_mdio_write().
c22:
- aspeed_mdio_read_c22()
- aspeed_mdio_write_c22()
c45:
- aspeed_mdio_read_c45()
- aspeed_mdio_write_c45()
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add aspeed_mdio_op() and aseed_mdio_get_data() for register accessing.
aspeed_mdio_op() handles operations, write command to control register,
then check and wait operations is finished (bit 31 is cleared).
aseed_mdio_get_data() fetchs the result value of operation from data
register.
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the MDIO bus will have the hardware default bus frequency.
Read the desired frequency of the bus from the device tree and configure
it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't support clause 45 register access yet, but doesn't
check if the access is a c45 one either. This leads to spurious register
reads and writes. Add the check.
Fixes: 542671fe4d ("net: phy: mscc-miim: Add MDIO driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN966x has two internal PHYs which are in reset by default. The
driver already supported the internal PHYs of the SparX-5. Now add
support for the LAN966x, too. Add a new compatible to distinguish them.
The LAN966x has additional control bits in this register, thus convert
the regmap_write() to regmap_update_bits() to leave the remaining bits
untouched. This doesn't change anything for the SparX-5 SoC, because
there, the register consists only of reset bits.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the magic numbers by macros which are already defined. It seems
the original commit missed to use them.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver can have up to two regmaps. If the second one is registered
its debugfs entry will have the same name as the first one and the
following error will be printed:
[ 3.833521] debugfs: Directory 'e200413c.mdio' with parent 'regmap' already present!
Give the second regmap a name to avoid this.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312224140.4173930-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of DT-configured systems it may be hard to identify the PHY
interrupt in the /proc/interrupts output. Therefore add the name to
the id to make clearer that it's about a device on a muxed mdio bus.
In my case:
Now: mdio_mux-0.e40908ff:08
Before: 0.e40908ff:08
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/00b4bb1e-98f9-b4e7-5549-e095a4701f66@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Experimentation shows that PHY detect might fail when the code attempts
MDIO bus read immediately after clock enable. Add delay to stabilize the
clock before bus access.
PHY detect failure started to show after commit 7590fc6f80 ("net:
mdio: Demote probed message to debug print") that removed coincidental
delay between clock enable and bus access.
10ms is meant to match the time it take to send the probed message over
UART at 115200 bps. This might be a far overshoot.
Fixes: 23a890d493 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix loading of the driver when built as a module.
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's build error while CONFIG_REGMAP_MMIO is not set
and CONFIG_MDIO_MSCC_MIIM=m.
ERROR: modpost: "__devm_regmap_init_mmio_clk"
[drivers/net/mdio/mdio-mscc-miim.ko] undefined!
Add the depend of REGMAP_MMIO to fix it.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130110209.804536-1-dtcccc@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the blamed commit, the second memory resource was not considered
anymore as optional. On some platforms like sparx5 the second resource
is optional. So add it back as optional and restore the comment that
says so.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to a shared MDIO access implementation by way of the mdio-mscc-miim
driver.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize regmap instead of __iomem to perform indirect mdio access. This
will allow for custom regmaps to be used by way of the mscc_miim_setup
function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap() instead of ioremap() to avoid iounmap() missing.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue happened randomly in runtime. The message "Link is Down" is
popped but soon it recovered to "Link is Up".
The "Link is Down" results from the incorrect read data for reading the
PHY register via MDIO bus. The correct sequence for reading the data
shall be:
1. fire the command
2. wait for command done (this step was missing)
3. wait for data idle
4. read data from data register
Cc: stable@vger.kernel.org
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The second resource is optional which is only provided on the chipset
IPQ5018. But the blamed commit ignores that and if the resource is
not there it just fails.
the resource is used like this,
if (priv->eth_ldo_rdy) {
val = readl(priv->eth_ldo_rdy);
val |= BIT(0);
writel(val, priv->eth_ldo_rdy);
fsleep(IPQ_PHY_SET_DELAY_US);
}
This patch reverts that to still allow the second resource to be optional
because other SoC have the some MDIO controller and doesn't need to
second resource.
Fixes: fa14d03e01 ("net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()")
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210928134849.2092-1-caihuoqing@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the documentation the second resource is optional. But the
blamed commit ignores that and if the resource is not there it just
fails.
This patch reverts that to still allow the second resource to be
optional because other SoC have the some MDIO controller and doesn't
need to second resource.
Fixes: 672a1c3949 ("net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa19644 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole point of devm_* APIs is that you don't have to undo them if you
are returning an error that's going to get propagated out of a probe()
function. So delete unnecessary devm_kfree() call in the error return path.
Fixes: b601616681 ("mdio: mux: Correct mdio_mux_init error path issues")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPQ MDIO driver currently supports the chipset IPQ40xx, IPQ807x,
IPQ60xx and IPQ50xx.
Add the compatible 'qcom,ipq5018-mdio' because of ethernet LDO dedicated
to the IPQ5018 platform.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. configure the MDIO clock source frequency.
2. the LDO resource is needed to configure the ethernet LDO available
for CMN_PLL.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly implemented fwnode_mdbiobus_register turned out to be
problematic - in case the fwnode_/of_/acpi_mdio are built as
modules, a dependency cycle can be observed during the depmod phase of
modules_install, eg.:
depmod: ERROR: Cycle detected: fwnode_mdio -> of_mdio -> fwnode_mdio
depmod: ERROR: Found 2 modules in dependency cycles!
OR:
depmod: ERROR: Cycle detected: acpi_mdio -> fwnode_mdio -> acpi_mdio
depmod: ERROR: Found 2 modules in dependency cycles!
A possible solution could be to rework fwnode_mdiobus_register,
so that to merge the contents of acpi_mdiobus_register and
of_mdiobus_register. However feasible, such change would
be very intrusive and affect huge amount of the of_mdiobus_register
users.
Since there are currently 2 users of ACPI and MDIO
(xgmac_mdio and mvmdio), withdraw the fwnode_mdbiobus_register
and roll back to a simple 'if' condition in affected drivers.
Fixes: 62a6ef6a99 ("net: mdiobus: Introduce fwnode_mdbiobus_register()")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new helper function that
wraps acpi_/of_ mdiobus_register() and allows its
usage via common fwnode_ interface.
Fall back to raw mdiobus_register() in case CONFIG_FWNODE_MDIO
is not enabled, in order to satisfy compatibility
in all future user drivers.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly introduced helper to setup both the of_node and the
fwnode for a given device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By mistake, the of_node of the MDIO device was not setup in the patch
linked below. As a consequence, any PHY driver that depends on the
of_node in its probe callback was not be able to successfully finish its
probe on a PHY, thus the Generic PHY driver was used instead.
Fix this by actually setting up the of_node.
Fixes: bc1bee3b87 ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define acpi_mdiobus_register() to Register mii_bus and create PHYs for
each ACPI child node.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor of_mdiobus_register_phy() to use fwnode_mdiobus_register_phy().
Also, remove the of_find_mii_timestamper() since the fwnode variant is
used instead.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce fwnode_mdiobus_register_phy() to register PHYs on the
mdiobus. From the compatible string, identify whether the PHY is
c45 and based on this create a PHY device instance which is
registered on the mdiobus.
Along with fwnode_mdiobus_register_phy() also introduce
fwnode_find_mii_timestamper() and fwnode_mdiobus_phy_device_register()
since they are needed.
While at it, also use the newly introduced fwnode operation in
of_mdiobus_phy_device_register().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of unregister_mii_timestamper() currently check for NULL
value of mii_ts before calling it.
Place the NULL check inside unregister_mii_timestamper() and update
the callers accordingly.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of fwnode_get_phy_id(), refactor of_get_phy_id()
to use fwnode equivalent.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor of_phy_find_device() to use fwnode_phy_find_device().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define fwnode_mdio_find_device() to get a pointer to the
mdio_device from fwnode passed to the function.
Refactor of_mdio_find_device() to use fwnode_mdio_find_device().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code and avoid a null-ptr-deref by checking 'res' in it.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
informations ==> information
typicaly ==> typically
derrive ==> derive
eventhough ==> even though
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the use of the qca8k dsa driver, some problem arised related to
port status detection. With a load on a specific port (for example a
simple speed test), the driver starts to behave in a strange way and
garbage data is produced. To address this, enlarge the sleep delay and
address a bug for the reg offset 31 that require additional delay for
this specific reg.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio drivers should not use REGCHACHE. Also disable locking since it's
handled by the mdio users and regmap is always accessed atomically.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix mixed whitespace and tab for define spacing.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
'bus->mii_bus' has been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the error handling path of the
probe function and in remove function.
Suggested-By: Andrew Lunn <andrew@lunn.ch>
Fixes: 35d2aeac98 ("phy: mdio-octeon: Use devm_mdiobus_alloc_size()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
'bus->mii_bus' have been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the remove function.
Fixes: 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMI0 is a mangled version of MDIO. The main low level difference is
the MDIO C22 OP code is always 0, not 0x2 or 0x1 for Read/Write. The
read/write information is instead encoded in the PHY address.
Extend the bit-bang code to allow the op code to be overridden, but
default to normal C22 values. Add an extra compatible to the mdio-gpio
driver, and when this compatible is present, set the op codes to 0.
A higher level driver, sitting on top of the basic MDIO bus driver can
then implement the rest of the microchip SMI0 odderties.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
