Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240409133307.2058099-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the qmi_wwan driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240409133307.2058099-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enabling/disabling of EEE in the MAC should happen as a result of
auto negotiation. So move the enable/disable into
lan783xx_phy_link_status_change() which gets called by phylib when
there is a change in link status.
lan78xx_set_eee() now just programs the hardware with the LPI
timer value, and passed everything else to phylib, so it can correctly
setup the PHY.
lan743x_get_eee() relies on phylib doing most of the work, the
MAC driver just adds the LPI timer value.
Call phy_support_eee() to indicate the MAC does actually support EEE.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mac address can not be read from the device registers or the
devicetree, a random address is generated, but this was already done from
usbnet_probe, so it is not necessary to call eth_hw_addr_random from here
again to generate another random address.
Indeed, when reset was also executed from bind, generate another random mac
address invalidated the check from usbnet_probe to configure if the assigned
mac address for the interface was random or not, because it is comparing
with the initial generated random address. Now, with only a reset from open
operation, it is just a harmless simplification.
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the commit d2689b6a86 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset is not executed from bind operation and
mac address is not read from the device registers or the devicetree at that
moment. Since the check to configure if the assigned mac address is random
or not for the interface, happens after the bind operation from
usbnet_probe, the interface keeps configured as random address, although the
address is correctly read and set during open operation (the only reset
now).
In order to keep only one reset for the device and to avoid the interface
always configured as random address, after reset, configure correctly the
suitable field from the driver, if the mac address is read successfully from
the device registers or the devicetree. Take into account if a locally
administered address (random) was previously stored.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240403132158.344838-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the unknown device, rtl8152_cfgselector_choose_configuration()
should return a negative value. Then, usb_choose_configuration() would
set a configuration for CDC ECM or NCM mode. Otherwise, there is no
usb interface driver for the device.
Fixes: aa4f2b3e41 ("r8152: Choose our USB config with choose_configuration() rather than probe()")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20240308075206.33553-436-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240306142643.2429409-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the usbnet driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240306142643.2429409-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add check for usbnet_get_endpoints() and return the error if it fails
in order to transfer the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 19a38d8e0a ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support")
Link: https://lore.kernel.org/r/20240305075927.261284-1-nichen@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
idev->cnf.forwarding and net->ipv6.devconf_all->forwarding
might be read locklessly, add appropriate READ_ONCE()
and WRITE_ONCE() annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver has some asymmetry in the runtime PM calls. On lan78xx_open()
it will call usb_autopm_get() and unconditionally usb_autopm_put(). And
on lan78xx_stop() it will call only usb_autopm_put(). So far, it was
working only because this driver do not activate autosuspend by default,
so it was visible only by warning "Runtime PM usage count underflow!".
Since, with current driver, we can't use runtime PM with active link,
execute lan78xx_open()->usb_autopm_put() only in error case. Otherwise,
keep ref counting high as long as interface is open.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Rework determining if EEE is active to make is similar as to how
phylib decides, and make use of a phylib helper to validate if EEE is
valid in for the current link mode. This then requires that PHYLIB is
selected.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable BH around the call to napi_schedule() to avoid following
error:
NOHZ tick-stop error: local softirq work is pending, handler #08!!!
Fixes: ec4c7e1239 ("lan78xx: Introduce NAPI polling support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240226110820.2113584-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863f ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c ("lan78xx: Set ASD in MAC_CR when EEE is enabled.")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for the SYS TEC USB-SPEmodule1 10Base-T1L
ethernet device to the existing smsc95xx driver by adding the new
USB VID/PID pair.
Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Link: https://lore.kernel.org/r/20240219053413.4732-1-andre.werner@systec-electronic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the hso_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the wlan_type
and wwan_type variables to be constant structures as well, placing it into
read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty core
and drivers in here, along with the usual set of rs485 updates (someday
this might work properly...) Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeUaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyOgCgp1uhP/b9iW6qM7qL6OYEG6idI0kAnj0VASNm
vSI69HmdKKwo69YLOSBp
=14n1
-----END PGP SIGNATURE-----
Merge tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
eee_active is set by phy_ethtool_get_eee() already, using the same
logic plus an additional check against link speed/duplex values.
See genphy_c45_eee_is_active() for details.
So we can remove this line.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/b086b296-0a1b-42d4-8e2b-ef6682598185@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- Revert "net: ipv6/addrconf: clamp preferred_lft to the minimum
required", it caused issues on networks where routers send prefixes
with preferred_lft=0
- wifi:
- iwlwifi: pcie: don't synchronize IRQs from IRQ, prevent deadlock
- mac80211: fix re-adding debugfs entries during reconfiguration
Current release - new code bugs:
- tcp: print AO/MD5 messages only if there are any keys
Previous releases - regressions:
- virtio_net: fix missing dma unmap for resize, prevent OOM
Previous releases - always broken:
- mptcp: prevent tcp diag from closing listener subflows
- nf_tables:
- set transport header offset for egress hook, fix IPv4 mangling
- skip set commit for deleted/destroyed sets, avoid double deactivation
- nat: make sure action is set for all ct states, fix openvswitch
matching on ICMP packets in related state
- eth: mlxbf_gige: fix receive hang under heavy traffic
- eth: r8169: fix PCI error on system resume for RTL8168FP
- net: add missing getsockopt(SO_TIMESTAMPING_NEW) and cmsg handling
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=+se8
-----END PGP SIGNATURE-----
Merge tag 'net-6.7-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and netfilter.
We haven't accumulated much over the break. If it wasn't for the
uninterrupted stream of fixes for Intel drivers this PR would be very
slim. There was a handful of user reports, however, either they stood
out because of the lower traffic or users have had more time to test
over the break. The ones which are v6.7-relevant should be wrapped up.
Current release - regressions:
- Revert "net: ipv6/addrconf: clamp preferred_lft to the minimum
required", it caused issues on networks where routers send prefixes
with preferred_lft=0
- wifi:
- iwlwifi: pcie: don't synchronize IRQs from IRQ, prevent deadlock
- mac80211: fix re-adding debugfs entries during reconfiguration
Current release - new code bugs:
- tcp: print AO/MD5 messages only if there are any keys
Previous releases - regressions:
- virtio_net: fix missing dma unmap for resize, prevent OOM
Previous releases - always broken:
- mptcp: prevent tcp diag from closing listener subflows
- nf_tables:
- set transport header offset for egress hook, fix IPv4 mangling
- skip set commit for deleted/destroyed sets, avoid double deactivation
- nat: make sure action is set for all ct states, fix openvswitch
matching on ICMP packets in related state
- eth: mlxbf_gige: fix receive hang under heavy traffic
- eth: r8169: fix PCI error on system resume for RTL8168FP
- net: add missing getsockopt(SO_TIMESTAMPING_NEW) and cmsg handling"
* tag 'net-6.7-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
net/tcp: Only produce AO/MD5 logs if there are any keys
net: Implement missing SO_TIMESTAMPING_NEW cmsg support
bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()
net: ravb: Wait for operating mode to be applied
asix: Add check for usbnet_get_endpoints
octeontx2-af: Re-enable MAC TX in otx2_stop processing
octeontx2-af: Always configure NIX TX link credits based on max frame size
net/smc: fix invalid link access in dumping SMC-R connections
net/qla3xxx: fix potential memleak in ql_alloc_buffer_queues
virtio_net: fix missing dma unmap for resize
igc: Fix hicredit calculation
ice: fix Get link status data length
i40e: Restore VF MSI-X state during PCI reset
i40e: fix use-after-free in i40e_aqc_add_filters()
net: Save and restore msg_namelen in sock_sendmsg
netfilter: nft_immediate: drop chain reference counter on error
netfilter: nf_nat: fix action not being set for all ct states
net: bcmgenet: Fix FCS generation for fragmented skbuffs
mptcp: prevent tcp diag from closing listener subflows
MAINTAINERS: add Geliang as reviewer for MPTCP
...
Add check for usbnet_get_endpoints() and return the error if it fails
in order to transfer the error.
Fixes: 16626b0cc3 ("asix: Add a new driver for the AX88172A")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is disconnected we get the following messages showing
failed operations:
Nov 28 20:22:11 localhost kernel: usb 2-3: USB disconnect, device number 2
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: unregister 'ax88179_178a' usb-0000:02:00.0-3, ASIX AX88179 USB 3.0 Gigabit Ethernet
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to read reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0001: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
The reason is that although the device is detached, normal stop and
unbind operations are commanded from the driver. These operations are
not necessary in this situation, so avoid these logs when the device is
detached if the result of the operation is -ENODEV and if the new flag
informing about the disconnecting status is enabled.
cc: <stable@vger.kernel.org>
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231207175007.263907-1-jtornosm@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ASUS USB-C2500 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Kelly Kane <kelly@hawknetworks.com>
Link: https://lore.kernel.org/r/20231203011712.6314-1-kelly@hawknetworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If you deauthorize the r8152 device (by writing 0 to the "authorized"
field in sysfs) and then reauthorize it (by writing a 1) then it no
longer works. This is because when you do the above we lose the
special configuration that we set in rtl8152_cfgselector_probe().
Deauthorizing causes the config to be set to -1 and then reauthorizing
runs the default logic for choosing the best config.
I made an attempt to fix it so that the config is kept across
deauthorizing / reauthorizing [1] but it was a bit ugly.
Let's instead use the new USB core feature to override
choose_configuration().
This patch relies upon the patches ("usb: core: Don't force USB
generic_subclass drivers to define probe()") and ("usb: core: Allow
subclassed USB drivers to override usb_choose_configuration()")
[1] https://lore.kernel.org/r/20231130154337.1.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Link: https://lore.kernel.org/r/20231201102946.v2.3.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_aldps_en().
Fixes: 4214cc550b ("r8152: check if disabling ALDPS is finished")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_pre_firmware_1().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in
r8156b_wait_loading_flash().
Fixes: 195aae321c ("r8152: support new chips")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commits added checks for RTL8152_INACCESSIBLE in the loops in
the driver. There are still a few more that keep tripping the driver
up in error cases and make things take longer than they should. Add
those in.
All the loops that are part of this commit existed in some form or
another since the r8152 driver was first introduced, though
RTL8152_INACCESSIBLE was known as RTL8152_UNPLUG before commit
715f67f33a ("r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit d9962b0d42 ("r8152: Block future register access if
register access fails") there is a race condition that can happen
between the USB device reset thread and napi_enable() (not) getting
called during rtl8152_open(). Specifically:
* While rtl8152_open() is running we get a register access error
that's _not_ -ENODEV and queue up a USB reset.
* rtl8152_open() exits before calling napi_enable() due to any reason
(including usb_submit_urb() returning an error).
In that case:
* Since the USB reset is perform in a separate thread asynchronously,
it can run at anytime USB device lock is not held - even before
rtl8152_open() has exited with an error and caused __dev_open() to
clear the __LINK_STATE_START bit.
* The rtl8152_pre_reset() will notice that the netif_running() returns
true (since __LINK_STATE_START wasn't cleared) so it won't exit
early.
* rtl8152_pre_reset() will then hang in napi_disable() because
napi_enable() was never called.
We can fix the race by making sure that the r8152 reset routines don't
run at the same time as we're opening the device. Specifically we need
the reset routines in their entirety rely on the return value of
netif_running(). The only way to reliably depend on that is for them
to hold the rntl_lock() mutex for the duration of reset.
Grabbing the rntl_lock() mutex for the duration of reset seems like a
long time, but reset is not expected to be common and the rtnl_lock()
mutex is already held for long durations since the core grabs it
around the open/close calls.
Fixes: d9962b0d42 ("r8152: Block future register access if register access fails")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
'serial_table' is global, so there is no need to initialize it to NULLs
at the module load. Drop this unneeded for loop.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20231121092258.9334-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's preferred NOT to emit anything during the module load and unload
(in case the un/load was successful). So drop these prints from hso
along with global 'version'. It even contains no version after all.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20231121092258.9334-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device is always reset two consecutive times (ax88179_reset is called
twice), one from usbnet_probe during the device binding and the other from
usbnet_open.
Remove the non-necessary reset during the device binding and let the reset
operation from open to keep the normal behavior (tested with generic ASIX
Electronics Corp. AX88179 Gigabit Ethernet device).
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120121239.54504-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a device sends a packet that is inbetween 0
and sizeof(u64) the value passed to skb_trim()
as length will wrap around ending up as some very
large value.
The driver will then proceed to parse the header
located at that position, which will either oops or
process some random value.
The fix is to check against sizeof(u64) rather than
0, which the driver currently does. The issue exists
since the introduction of the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the functions to read/write registers can fail, most of
the places in the r8152 driver that read/write register values don't
check error codes. The lack of error code checking is problematic in
at least two ways.
The first problem is that the r8152 driver often uses code patterns
similar to this:
x = read_register()
x = x | SOME_BIT;
write_register(x);
...with the above pattern, if the read_register() fails and returns
garbage then we'll end up trying to write modified garbage back to the
Realtek adapter. If the write_register() succeeds that's bad. Note
that as of commit f53a7ad189 ("r8152: Set memory to all 0xFFs on
failed reg reads") the "garbage" returned by read_register() will at
least be consistent garbage, but it is still garbage.
It turns out that this problem is very serious. Writing garbage to
some of the hardware registers on the Ethernet adapter can put the
adapter in such a bad state that it needs to be power cycled (fully
unplugged and plugged in again) before it can enumerate again.
The second problem is that the r8152 driver generally has functions
that are long sequences of register writes. Assuming everything will
be OK if a random register write fails in the middle isn't a great
assumption.
One might wonder if the above two problems are real. You could ask if
we would really have a successful write after a failed read. It turns
out that the answer appears to be "yes, this can happen". In fact,
we've seen at least two distinct failure modes where this happens.
On a sc7180-trogdor Chromebook if you drop into kdb for a while and
then resume, you can see:
1. We get a "Tx timeout"
2. The "Tx timeout" queues up a USB reset.
3. In rtl8152_pre_reset() we try to reinit the hardware.
4. The first several (2-9) register accesses fail with a timeout, then
things recover.
The above test case was actually fixed by the patch ("r8152: Increase
USB control msg timeout to 5000ms as per spec") but at least shows
that we really can see successful calls after failed ones.
On a different (AMD) based Chromebook with a particular adapter, we
found that during reboot tests we'd also sometimes get a transitory
failure. In this case we saw -EPIPE being returned sometimes. Retrying
worked, but retrying is not always safe for all register accesses
since reading/writing some registers might have side effects (like
registers that clear on read).
Let's fully lock out all register access if a register access fails.
When we do this, we'll try to queue up a USB reset and try to unlock
register access after the reset. This is slightly tricker than it
sounds since the r8152 driver has an optimized reset sequence that
only works reliably after probe happens. In order to handle this, we
avoid the optimized reset if probe didn't finish. Instead, we simply
retry the probe routine in this case.
When locking out access, we'll use the existing infrastructure that
the driver was using when it detected we were unplugged. This keeps us
from getting stuck in delay loops in some parts of the driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever the RTL8152_UNPLUG is set that just tells the driver that all
accesses will fail and we should just immediately bail. A future patch
will use this same concept at a time when the driver hasn't actually
been unplugged but is about to be reset. Rename the flag in
preparation for the future patch.
This is a no-op change and just a search and replace.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the adapter is unplugged while we're looping in r8153b_ups_en() /
r8153c_ups_en() we could end up looping for 10 seconds (20 ms * 500
loops). Add code similar to what's done in other places in the driver
to check for unplug and bail.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the adapter is unplugged while we're looping in
rtl_phy_patch_request() we could end up looping for 10 seconds (2 ms *
5000 loops). Add code similar to what's done in other places in the
driver to check for unplug and bail.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in rtl8152_probe() is missing a call to release
firmware. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: a028a9e003 ("r8152: move the settings of PHY to a work queue")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
Other implementations of .*get_drvinfo use strscpy so this patch brings
lan78xx_get_drvinfo() in line as well:
igb/igb_ethtool.c +851
static void igb_get_drvinfo(struct net_device *netdev,
igbvf/ethtool.c
167:static void igbvf_get_drvinfo(struct net_device *netdev,
i40e/i40e_ethtool.c
1999:static void i40e_get_drvinfo(struct net_device *netdev,
e1000/e1000_ethtool.c
529:static void e1000_get_drvinfo(struct net_device *netdev,
ixgbevf/ethtool.c
211:static void ixgbevf_get_drvinfo(struct net_device *netdev,
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231012-strncpy-drivers-net-usb-lan78xx-c-v1-1-99d513061dfc@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
kernel/bpf/verifier.c
829955981c ("bpf: Fix verifier log for async callback return values")
a923819fb2 ("bpf: Treat first argument as return value for bpf_throw")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A bulk transfer of the USB may contain many packets. And, the total
number of the packets in the bulk transfer may be more than budget.
Originally, only budget packets would be handled by napi_gro_receive(),
and the other packets would be queued in the driver for next schedule.
This patch would break the loop about getting next bulk transfer, when
the budget is exhausted. That is, only the current bulk transfer would
be handled, and the other bulk transfers would be queued for next
schedule. Besides, the packets which are more than the budget in the
current bulk trasnfer would be still queued in the driver, as the
original method.
In addition, a bulk transfer wouldn't contain more than 400 packets, so
the check of queue length is unnecessary. Therefore, I replace it with
WARN_ON_ONCE().
Fixes: cf74eb5a5b ("eth: r8152: try to use a normal budget")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230926111714.9448-433-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e44 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
The D-Link DUB-E250 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Antonio Napolitano <anton@polit.no>
Link: https://lore.kernel.org/r/CV200KJEEUPC.WPKAHXCQJ05I@mercurius
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mario reports that loading r8152 on his system leads to a:
netif_napi_add_weight() called with weight 256
warning getting printed. We don't have any solid data
on why such high budget was chosen, and it may cause
stalls in processing other softirqs and rt threads.
So try to switch back to the default (64) weight.
If this slows down someone's system we should investigate
which part of stopping starting the NAPI poll in this
driver are expensive.
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/all/0bfd445a-81f7-f702-08b0-bd5a72095e49@amd.com/
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230814153521.2697982-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need for two more variables in hso_serial_write(). Switch to
min_t() and eliminate those.
Furthermore, the 'if-goto' is superfluous as memcpy() of zero count is a
nop. So is addition of zero. So remove the 'if-goto' completely.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20230810091510.13006-36-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timer dev->stat_monitor can schedule the delayed work dev->wq and
the delayed work dev->wq can also arm the dev->stat_monitor timer.
When the device is detaching, the net_device will be deallocated. but
the net_device private data could still be dereferenced in delayed work
or timer handler. As a result, the UAF bugs will happen.
One racy situation is shown below:
(Thread 1) | (Thread 2)
lan78xx_stat_monitor() |
... | lan78xx_disconnect()
lan78xx_defer_kevent() | ...
... | cancel_delayed_work_sync(&dev->wq);
schedule_delayed_work() | ...
(wait some time) | free_netdev(net); //free net_device
lan78xx_delayedwork() |
//use net_device private data |
dev-> //use |
Although we use cancel_delayed_work_sync() to cancel the delayed work
in lan78xx_disconnect(), it could still be scheduled in timer handler
lan78xx_stat_monitor().
Another racy situation is shown below:
(Thread 1) | (Thread 2)
lan78xx_delayedwork |
mod_timer() | lan78xx_disconnect()
| cancel_delayed_work_sync()
(wait some time) | if (timer_pending(&dev->stat_monitor))
| del_timer_sync(&dev->stat_monitor);
lan78xx_stat_monitor() | ...
lan78xx_defer_kevent() | free_netdev(net); //free
//use net_device private data|
dev-> //use |
Although we use del_timer_sync() to delete the timer, the function
timer_pending() returns 0 when the timer is activated. As a result,
the del_timer_sync() will not be executed and the timer could be
re-armed.
In order to mitigate this bug, We use timer_shutdown_sync() to shutdown
the timer and then use cancel_delayed_work_sync() to cancel the delayed
work. As a result, the net_device could be deallocated safely.
What's more, the dev->flags is set to EVENT_DEV_DISCONNECT in
lan78xx_disconnect(). But it could still be set to EVENT_STAT_UPDATE
in lan78xx_stat_monitor(). So this patch put the set_bit() behind
timer_shutdown_sync().
Fixes: 77dfff5bb7 ("lan78xx: Fix race condition in disconnect handling")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLA_BP_0 ~ PLA_BP_15 (0xfc28 ~ 0xfc46) are continuous registers, so we
could combine the control transfers into one control transfer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230726030808.9093-419-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reduce the control transfer if all bytes of first or the last DWORD are
written.
The original method is to split the control transfer into three parts
(the first DWORD, middle continuous data, and the last DWORD). However,
they could be combined if whole bytes of the first DWORD or last DWORD
are written. That is, the first DWORD or the last DWORD could be combined
with the middle continuous data, if the byte_en is 0xff.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230726030808.9093-418-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add CDC-ECM support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In CDC-ECM mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RmNet support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In RmNet mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Link: https://lore.kernel.org/r/20230626125336.3127-1-davide.tronchin.94@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move declarations into include/net/gso.h and code into net/core/gso.c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230608191738.3947077-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This module has for a long time not been limited to iPhone <= 3GS.
Update description to match the actual state of the driver.
Remove dead link from 2010, instead reference an existing userspace
iOS device pairing implementation as part of libimobiledevice.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent iOS releases support CDC NCM encapsulation on RX. This mode is
the default on macOS and Windows. In this mode, an iOS device may include
one or more Ethernet frames inside a single URB.
Freshly booted iOS devices start in legacy mode, but are put into
NCM mode by the official Apple driver. When reconnecting such a device
from a macOS/Windows machine to a Linux host, the device stays in
NCM mode, making it unusable with the legacy ipheth driver code.
To correctly support such a device, the driver has to either support
the NCM mode too, or put the device back into legacy mode.
To match the behaviour of the macOS/Windows driver, and since there
is no documented control command to revert to legacy mode, implement
NCM support. The device is attempted to be put into NCM mode by default,
and falls back to legacy mode if the attempt fails.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The behaviour of the official iOS tethering driver on macOS is to not
transmit any trailing padding at the end of URBs. This is applicable
to both NCM and legacy modes, including older devices.
Adapt the driver to not include trailing padding in TX URBs, matching
the behaviour of the official macOS driver.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cleanup precedure in ipheth_probe will attempt to free a
NULL pointer in dev->ctrl_buf if the memory allocation for
this buffer is not successful. While kfree ignores NULL pointers,
and the existing code is safe, it is a better design to rearrange
the goto labels and avoid this.
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set supports_autosuspend = 1 for the rtl8152_cfgselector_driver.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting r8153b_rx_agg_chg_indicate() for 2.5G devices. The
r8153b_rx_agg_chg_indicate() has to be called after enabling tx/rx.
Otherwise, the coalescing settings are useless.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the poor throughput for 2.5G devices, when changing the speed from
auto mode to force mode. This patch is used to notify the MAC when the
mode is changed.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The feature of flow control becomes abnormal, if the device sends a
pause frame and the tx/rx is disabled before sending a release frame. It
causes the lost of packets.
Set PLA_RX_FIFO_FULL and PLA_RX_FIFO_EMPTY to zeros before disabling the
tx/rx. And, toggle FC_PATCH_TASK before enabling tx/rx to reset the flow
control patch and timer. Then, the hardware could clear the state and
the flow control becomes normal after enabling tx/rx.
Besides, remove inline for fc_pause_on_auto() and fc_pause_off_auto().
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
