Link status of SMSC LAN95xx chips is polled once per second, even though
they're capable of signaling PHY interrupts through the MAC layer.
Forward those interrupts to the PHY driver to avoid polling. Benefits
are reduced bus traffic, reduced CPU overhead and quicker interface
bringup.
Polling was introduced in 2016 by commit d69d169493 ("usbnet:
smsc95xx: fix link detection for disabled autonegotiation").
Back then, the LAN95xx driver neglected to enable the ENERGYON interrupt,
hence couldn't detect link-up events when auto-negotiation was disabled.
The proper solution would have been to enable the ENERGYON interrupt
instead of polling.
Since then, PHY handling was moved from the LAN95xx driver to the SMSC
PHY driver with commit 05b35e7eb9 ("smsc95xx: add phylib support").
That PHY driver is capable of link detection with auto-negotiation
disabled because it enables the ENERGYON interrupt.
Note that signaling interrupts through the MAC layer not only works with
the integrated PHY, but also with an external PHY, provided its
interrupt pin is attached to LAN95xx's nPHY_INT pin.
In the unlikely event that the interrupt pin of an external PHY is
attached to a GPIO of the SoC (or not connected at all), the driver can
be amended to retrieve the irq from the PHY's of_node.
To forward PHY interrupts to phylib, it is not sufficient to call
phy_mac_interrupt(). Instead, the PHY's interrupt handler needs to run
so that PHY interrupts are cleared. That's because according to page
119 of the LAN950x datasheet, "The source of this interrupt is a level.
The interrupt persists until it is cleared in the PHY."
https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf
Therefore, create an IRQ domain with a single IRQ for the PHY. In the
future, the IRQ domain may be extended to support the 11 GPIOs on the
LAN95xx.
Normally the PHY interrupt should be masked until the PHY driver has
cleared it. However masking requires a (sleeping) USB transaction and
interrupts are received in (non-sleepable) softirq context. I decided
not to mask the interrupt at all (by using the dummy_irq_chip's noop
->irq_mask() callback): The USB interrupt endpoint is polled in 1 msec
intervals and normally that's sufficient to wake the PHY driver's IRQ
thread and have it clear the interrupt. If it does take longer, worst
thing that can happen is the IRQ thread is woken again. No big deal.
Because PHY interrupts are now perpetually enabled, there's no need to
selectively enable them on suspend. So remove all invocations of
smsc95xx_enable_phy_wakeup_interrupts().
In smsc95xx_resume(), move the call of phy_init_hw() before
usbnet_resume() (which restarts the status URB) to ensure that the PHY
is fully initialized when an interrupt is handled.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch> # from a PHY perspective
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY interrupt is signaled, the SMSC LAN95xx driver updates the
MAC full duplex mode and PHY flow control registers based on cached data
in struct phy_device:
smsc95xx_status() # raises EVENT_LINK_RESET
usbnet_deferred_kevent()
smsc95xx_link_reset() # uses cached data in phydev
Simultaneously, phylib polls link status once per second and updates
that cached data:
phy_state_machine()
phy_check_link_status()
phy_read_status()
lan87xx_read_status()
genphy_read_status() # updates cached data in phydev
If smsc95xx_link_reset() wins the race against genphy_read_status(),
the registers may be updated based on stale data.
E.g. if the link was previously down, phydev->duplex is set to
DUPLEX_UNKNOWN and that's what smsc95xx_link_reset() will use, even
though genphy_read_status() may update it to DUPLEX_FULL afterwards.
PHY interrupts are currently only enabled on suspend to trigger wakeup,
so the impact of the race is limited, but we're about to enable them
perpetually.
Avoid the race by delaying execution of smsc95xx_link_reset() until
phy_state_machine() has done its job and calls back via
smsc95xx_handle_link_change().
Signaling EVENT_LINK_RESET on wakeup is not necessary because phylib
picks up link status changes through polling. So drop the declaration
of a ->link_reset() callback.
Note that the semicolon on a line by itself added in smsc95xx_status()
is a placeholder for a function call which will be added in a subsequent
commit. That function call will actually handle the INT_ENP_PHY_INT_
interrupt.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc95xx_reset() resets the PHY behind the PHY driver's back, which
seems like a bad idea generally. Remove that portion of the function.
We're about to use PHY interrupts instead of polling to detect link
changes on SMSC LAN95xx chips. Because smsc95xx_reset() is called from
usbnet_open(), PHY interrupt settings are lost whenever the net_device
is brought up.
There are two other callers of smsc95xx_reset(), namely smsc95xx_bind()
and smsc95xx_reset_resume(), and both may indeed benefit from a PHY
reset. However they already perform one through their calls to
phy_connect_direct() and phy_init_hw().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Gabriel Hojda <ghojda@yo2urs.ro>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving data from the Interrupt Endpoint, the SMSC LAN95xx driver
attempts to clear the signaled interrupts by writing "all ones" to the
Interrupt Status Register.
However the driver only ever enables a single type of interrupt, namely
the PHY Interrupt. And according to page 119 of the LAN950x datasheet,
its bit in the Interrupt Status Register is read-only. There's no other
way to clear it than in a separate PHY register:
https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf
Consequently, writing "all ones" to the Interrupt Status Register is
pointless and can be dropped.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2c9d6c2b87 ("usbnet: run unbind() before unregister_netdev()")
sought to fix a use-after-free on disconnect of USB Ethernet adapters.
It turns out that a different fix is necessary to address the issue:
https://lore.kernel.org/netdev/18b3541e5372bc9b9fc733d422f4e698c089077c.1650177997.git.lukas@wunner.de/
So the commit was not necessary.
The commit made binding and unbinding of USB Ethernet asymmetrical:
Before, usbnet_probe() first invoked the ->bind() callback and then
register_netdev(). usbnet_disconnect() mirrored that by first invoking
unregister_netdev() and then ->unbind().
Since the commit, the order in usbnet_disconnect() is reversed and no
longer mirrors usbnet_probe().
One consequence is that a PHY disconnected (and stopped) in ->unbind()
is afterwards stopped once more by unregister_netdev() as it closes the
netdev before unregistering. That necessitates a contortion in ->stop()
because the PHY may only be stopped if it hasn't already been
disconnected.
Reverting the commit allows making the call to phy_stop() unconditional
in ->stop().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 uses a custom napi weight, switch to the new
API for setting custom weight.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Oliver Neukum <oliver@neukum.org>
CC: David S. Miller <davem@davemloft.net>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Felix Fietkau <nbd@nbd.name>
CC: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
CC: Ryder Lee <ryder.lee@mediatek.com>
CC: Kalle Valo <kvalo@kernel.org>
CC: Matthias Brugger <matthias.bgg@gmail.com>
CC: Stanislaw Gruszka <stf_xl@wp.pl>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220317035514.6378-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports this issue
sr9800.h:166:53: warning: symbol 'SR9800_BULKIN_SIZE' was not declared. Should it be static?
Global variables should not be defined in header files.
This only works because sr9800.h in only included by sr9800.c
Change the storage-class specifier to static.
And since it does not change add type qualifier const.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to call spin_lock_bh() for you are already in a tasklet.
Signed-off-by: Yunbo Yu <yuyunbo519@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reporting of bogus MAC addresses and ignoring configuration of new
destination address wasn't observed outside of a range of ZTE devices,
among which this seems to be the common bug. Align rndis_host driver
with implementation found in cdc_ether, which also limits this workaround
to ZTE devices.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Certain ZTE modems, namely: MF823. MF831, MF910, built-in modem from
MF286R, expose both CDC-ECM and RNDIS network interfaces.
They have a trait of ignoring the locally-administered MAC address
configured on the interface both in CDC-ECM and RNDIS part,
and this leads to dropping of incoming traffic by the host.
However, the workaround was only present in CDC-ECM, and MF286R
explicitly requires it in RNDIS mode.
Re-use the workaround in rndis_host as well, to fix operation of MF286R
module, some versions of which expose only the RNDIS interface. Do so by
introducing new flag, RNDIS_DRIVER_DATA_DST_MAC_FIXUP, and testing for it
in rndis_rx_fixup. This is required, as RNDIS uses frame batching, and all
of the packets inside the batch need the fixup. This might introduce a
performance penalty, because test is done for every returned Ethernet
frame.
Apply the workaround to both "flavors" of RNDIS interfaces, as older ZTE
modems, like MF823 found in the wild, report the USB_CLASS_COMM class
interfaces, while MF286R reports USB_CLASS_WIRELESS_CONTROLLER.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduces a workaround for certain ZTE modems reporting invalid MAC
addresses over CDC-ECM.
The same issue was present on their RNDIS interface,which was fixed in
commit a5a18bdf74 ("rndis_host: Set valid random MAC on buggy devices").
However, internal modem of ZTE MF286R router, on its RNDIS interface, also
exhibits a second issue fixed already in CDC-ECM, of the device not
respecting configured random MAC address. In order to share the fixup for
this with rndis_host driver, export the workaround function, which will
be re-used in the following commit in rndis_host.
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
aqc111_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
Found doing variant analysis. Tested it with another driver (ax88179_178a), since
I don't have a aqc111 device to test it, but the code looks very similar.
Signed-off-by: Marcin Kozlowski <marcinguy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_alloc_skb() has assigned ssi->netdev to skb->dev if successed,
no need to repeat assignment.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout
the stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower
iTLB pressure and prevents identity mapping huge pages from
getting split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop
the user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if called
from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling
of TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmI7YBcACgkQMUZtbf5S
IrveSBAAmSNJlUK6vPsnNzs7IhsZnfI/AUjm2TCLZnlhKttbpI4A/4Pohk33V7RS
FGX7f8kjEfhUwrIiLDgeCnztNHRECrCmk6aZc/jLEvecmTauJ+f6kjShkDY/wix+
AkPHmrZnQeLPAEVuljDdV+sL6ik08+zQL7PazIYHsaSKKC0MGQptRwcri8PLRAKE
KPBAhVhleq2rAZ/ntprSN52F4Af6rpFTrPIWuN8Bqdbc9dy5094LT0mpOOWYvgr3
/DLvvAPuLemwyIQkjWknVKBRUAQcmNPC+BY3J8K3LRaiNhekGqOFan46BfqP+k2J
6DWu0Qrp2yWt4BMOeEToZR5rA6v5suUAMIBu8PRZIDkINXQMlIxHfGjZyNm0rVfw
7edNri966yus9OdzwPa32MIG3oC6PnVAwYCJAjjBMNS8sSIkp7wgHLkgWN4UFe2H
K/e6z8TLF4UQ+zFM0aGI5WZ+9QqWkTWEDF3R3OhdFpGrznna0gxmkOeV2YvtsgxY
cbS0vV9Zj73o+bYzgBKJsw/dAjyLdXoHUGvus26VLQ78S/VGunVKtItwoxBAYmZo
krW964qcC89YofzSi8RSKLHuEWtNWZbVm8YXr75u6jpr5GhMBu0CYefLs+BuZcxy
dw8c69cGneVbGZmY2J3rBhDkchbuICl8vdUPatGrOJAoaFdYKuw=
=ELpe
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
In case external PHY is used, we need to take care of embedded PHY.
Since there are no methods to disable this PHY from the MAC side and
keeping RMII reference clock, we need to suspend it.
This patch will reduce electrical noise (PHY is continuing to send FLPs)
and power consumption by 0,22W.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In most cases we use own mdio bus, there is no need to create and store
string for the PHY address.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already read chipid on probe. There is no need to read it on reset.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only difference is the reset code, so remove not needed duplicates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/driver-api/usb/URB.rst when a device
is unplugged usb_submit_urb() returns -ENODEV.
This error code propagates all the way up to usbnet_read_cmd() and
usbnet_write_cmd() calls inside the smsc95xx.c driver during
Ethernet cable unplug, unbind or reboot.
This causes the following errors to be shown on reboot, for example:
ci_hdrc ci_hdrc.1: remove, state 1
usb usb2: USB disconnect, device number 1
usb 2-1: USB disconnect, device number 2
usb 2-1.1: USB disconnect, device number 3
smsc95xx 2-1.1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: hardware isn't capable of remote wakeup
usb 2-1.4: USB disconnect, device number 4
ci_hdrc ci_hdrc.1: USB bus 2 deregistered
ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot!
reboot: Restarting system
Ignore the -ENODEV errors inside __smsc95xx_mdio_read() and
__smsc95xx_phy_wait_not_busy() and do not print error messages
when -ENODEV is returned.
Fixes: a049a30fc2 ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of manually disabling interrupts before invoking use
generic_handle_irq_safe() which can be invoked with enabled and disabled
interrupts.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: UNGLinuxDriver@microchip.com
Link: https://lore.kernel.org/r/20220211181500.1856198-7-bigeasy@linutronix.de
This functions are mostly same except of one hard coded "in_pm" variable.
So, rework them to reduce maintenance overhead.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220223110633.3006551-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices,
avoid FW assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Nrzq
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices, avoid FW
assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling"
* tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
bonding: force carrier update when releasing slave
nfp: flower: netdev offload check for ip6gretap
ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
ipv4: fix data races in fib_alias_hw_flags_set
net: dsa: lan9303: add VLAN IDs to master device
net: dsa: lan9303: handle hwaccel VLAN tags
vsock: remove vsock from connected table when connect is interrupted by a signal
Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
ping: fix the dif and sdif check in ping_lookup
net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
net: sched: limit TC_ACT_REPEAT loops
tipc: fix wrong notification node addresses
net: dsa: lantiq_gswip: fix use after free in gswip_remove()
ipv6: per-netns exclusive flowlabel checks
net: bridge: multicast: notify switchdev driver whenever MC processing gets disabled
CDC-NCM: avoid overflow in sanity checking
mctp: fix use after free
net: mscc: ocelot: fix use-after-free in ocelot_vlan_del()
bonding: fix data-races around agg_select_timer
dpaa2-eth: Initialize mutex used in one step timestamping path
...
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FN990
0x1071 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
hso_create_device() is only called from function that already use
GFP_KERNEL. And all the callers are called from the probe function.
So there is no need here to explicitly require a GFP_ATOMIC when
allocating memory.
Use GFP_KERNEL instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This SL-6000 says Direct Line, not Ethernet
v2: added Reporter and Link
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Ross Maynard <bids.7405@bigpond.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215361
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some small USB driver fixes for 5.17-rc4 that resolve some
reported issues and add new device ids:
- usb-serial new device ids
- ulpi cleanup fixes
- f_fs use-after-free fix
- dwc3 driver fixes
- ax88179_178a usb network driver fix
- usb gadget fixes
There is a revert at the end of this series to resolve a build problem
that 0-day found yesterday. Most of these have been in linux-next,
except for the last few, and all have now passed 0-day tests.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYgeLiw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylpQACaAnwfFoAxK5yr2IEu5WmxPmY0pSkAnROqF4JO
CQhohQ61DjpdK0ikJWsZ
=n8Yn
-----END PGP SIGNATURE-----
Merge tag 'usb-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for 5.17-rc4 that resolve some
reported issues and add new device ids:
- usb-serial new device ids
- ulpi cleanup fixes
- f_fs use-after-free fix
- dwc3 driver fixes
- ax88179_178a usb network driver fix
- usb gadget fixes
There is a revert at the end of this series to resolve a build problem
that 0-day found yesterday. Most of these have been in linux-next,
except for the last few, and all have now passed 0-day tests"
* tag 'usb-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "usb: dwc2: drd: fix soft connect when gadget is unconfigured"
usb: dwc2: drd: fix soft connect when gadget is unconfigured
usb: gadget: rndis: check size of RNDIS_MSG_SET command
USB: gadget: validate interface OS descriptor requests
usb: core: Unregister device on component_add() failure
net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup
usb: dwc3: gadget: Prevent core from processing stale TRBs
USB: serial: cp210x: add CPI Bulk Coin Recycler id
USB: serial: cp210x: add NCR Retail IO box id
USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
usb: gadget: f_uac2: Define specific wTerminalType
usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
usb: raw-gadget: fix handling of dual-direction-capable endpoints
usb: usb251xb: add boost-up property support
usb: ulpi: Call of_node_put correctly
usb: ulpi: Move of_node_put to ulpi_dev_release
USB: serial: option: add ZTE MF286D modem
USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
usb: f_fs: Fix use-after-free for epfile
usb: dwc3: xilinx: fix uninitialized return value
ax88179_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (hdr_off..hdr_off+2*pkt_cnt) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
I have tested that this can be used by a malicious USB device to send a
bogus ICMPv6 Echo Request and receive an ICMPv6 Echo Reply in response
that contains random kernel heap data.
It's probably also possible to get OOB writes from this on a
little-endian system somehow - maybe by triggering skb_cow() via IP
options processing -, but I haven't tested that.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide generic selftest support. Tested with LAN9500 and LAN9512.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot once again hit uninit value in asix driver. The problem still the
same -- asix_read_cmd() reads less bytes, than was requested by caller.
Since all read requests are performed via asix_read_cmd() let's catch
usb related error there and add __must_check notation to be sure all
callers actually check return value.
So, this patch adds sanity check inside asix_read_cmd(), that simply
checks if bytes read are not less, than was requested and adds missing
error handling of asix_read_cmd() all across the driver code.
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+6ca9f7867b77c2d316ac@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rx_buf is allocated we need to account for IPHETH_IP_ALIGN,
which reduces the usable size by 2 bytes. Otherwise we have 1512
bytes usable instead of 1514, and if we receive more than 1512
bytes, ipheth_rcvbulk_callback is called with status -EOVERFLOW,
after which the driver malfunctiones and all communication stops.
Resolves ipheth 2-1:4.2: ipheth_rcvbulk_callback: urb status: -75
Fixes: f33d9e2b48 ("usbnet: ipheth: fix connectivity with iOS 14")
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/all/B60B8A4B-92A0-49B3-805D-809A2433B46C@abv.bg/
Link: https://lore.kernel.org/all/24851bd2769434a5fc24730dce8e8a984c5a4505.1643699778.git.jan.kiszka@siemens.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Variable reg is being masked however the variable is never read
after this. The assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220123184035.112785-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On boards with LAN9514 and no preconfigured MAC address we don't get an
ip address from DHCP after commit a049a30fc2 ("net: usb: Correct PHY handling
of smsc95xx") anymore. Adding an explicit reset before starting the phy
fixes the issue.
[1]
https://lore.kernel.org/netdev/199eebbd6b97f52b9119c9fa4fd8504f8a34de18.camel@collabora.com/
From: Gabriel Hojda <ghojda@yo2urs.ro>
Fixes: a049a30fc2 ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Gabriel Hojda <ghojda@yo2urs.ro>
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com
Fixes: 2a36d70834 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit f77b83b5bb.
This change breaks multiple usb to ethernet dongles attached on Lenovo
USB hub.
Fixes: f77b83b5bb ("net: usb: r8152: Add MAC passthrough support for more Lenovo Docks")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Link: https://lore.kernel.org/r/20220105155102.8557-1-aaron.ma@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hytera makes a range of digital (DMR) radios. These radios can be
programmed to a allow a computer to control them over Ethernet over USB,
either using NCM or RNDIS.
This commit adds support for RNDIS for Hytera radios. I tested with a
Hytera PD785 and a Hytera MD785G. When these radios are programmed to
set up a Radio to PC Network using RNDIS, an USB interface will be added
with class 2 (Communications), subclass 2 (Abstract Modem Control) and
an interface protocol of 255 ("vendor specific" - lsusb even hints "MSFT
RNDIS?").
This patch is similar to the solution of this StackOverflow user, but
that only works for the Hytera MD785:
https://stackoverflow.com/a/53550858
To use the "Radio to PC Network" functionality of Hytera DMR radios, the
radios need to be programmed correctly in CPS (Hytera's Customer
Programming Software). "Forward to PC" should be checked in "Network"
(under "General Setting" in "Conventional") and the "USB Network
Communication Protocol" should be set to RNDIS.
Signed-off-by: Thomas Toye <thomas@toye.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames
that are longer than 1518 octets, for example, Ethernet frames that
contain 802.1Q VLAN tags.
The frames are sent to the pegasus driver via USB but the driver
discards them because they have the Long_pkt field set to 1 in the
received status report. The function read_bulk_callback of the pegasus
driver treats such received "packets" (in the terminology of the
hardware) as errors but the field simply does just indicate that the
Ethernet frame (MAC destination to FCS) is longer than 1518 octets.
It seems that in the 1990s there was a distinction between
"giant" (> 1518) and "runt" (< 64) frames and the hardware includes
flags to indicate this distinction. It seems that the purpose of the
distinction "giant" frames was to not allow infinitely long frames due
to transmission errors and to allow hardware to have an upper limit of
the frame size. However, the hardware already has such limit with its
2048 octet receive buffer and, therefore, Long_pkt is merely a
convention and should not be treated as a receive error.
Actually, the hardware is even able to receive Ethernet frames with 2048
octets which exceeds the claimed limit frame size limit of the driver of
1536 octets (PEGASUS_MTU).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matthias-Christian Ott <ott@mirix.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some chances that the actual base of hardware is different
from the value recorded by driver, so we have to reset the variable
of ocp_base to sync it.
Set ocp_base to -1. Then, it would be updated and the new base would be
set to the hardware next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It needs to set mdio force mode. Otherwise, link off always occurs when
setting force speed.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If asix_read_cmd() returns 0 on 30th interation, 0 will be returned from
asix_check_host_enable(), which is logically wrong. Fix it by returning
-ETIMEDOUT explicitly if we have exceeded 30 iterations
Also, replaced 30 with #define as suggested by Andrew
Fixes: a786e3195d ("net: asix: fix uninit value bugs")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ecd3470ce6c2d5697ac635d0d3b14a47defb4acb.1640117288.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asix_read_cmd() may read less than sizeof(smsr) bytes and in this case
smsr will be uninitialized.
Fail log:
BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline]
BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497
BUG: KMSAN: uninit-value in asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497
asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline]
asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497
asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+f44badb06036334e867a@syzkaller.appspotmail.com
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/8966e3b514edf39857dd93603fc79ec02e000a75.1640117288.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff830a5b5f len:184 put:172 \
head:ffff888119227c00 data:ffff888119227c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:110!
RIP: 0010:skb_panic+0x14f/0x160 net/core/skbuff.c:106
<snip>
Call Trace:
<IRQ>
skb_over_panic+0x2c/0x30 net/core/skbuff.c:115
skb_put+0x205/0x210 net/core/skbuff.c:1877
skb_put_zero include/linux/skbuff.h:2270 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1116 [inline]
cdc_ncm_fill_tx_frame+0x127f/0x3d50 drivers/net/usb/cdc_ncm.c:1293
cdc_ncm_tx_fixup+0x98/0xf0 drivers/net/usb/cdc_ncm.c:1514
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org>
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes: cc89c323a3 ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a NAPI-style approach for processing completed
Rx URBs that contributes to improving driver throughput and reducing
CPU load.
Packets in completed URBs are copied to NAPI SKBs and passed to the
network stack for processing. Each frame passed to the stack is one
work item in the NAPI budget.
If the NAPI budget is consumed and frames remain, they are added to
an overflow queue that is processed at the start of the next NAPI
polling cycle.
The NAPI handler is also responsible for copying pending Tx data to
Tx URBs and submitting them to the USB host controller for
transmission.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove hardware-specific header length adjustment as it is no longer
required. It also breaks generic receive offload (GRO) processing of
received TCP frames that results in a TCP ACK being sent for each
received frame.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move position of rx_submit() to remove forward declaration of
rx_complete() which is now no longer required.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new approach to allocating and managing
Rx URBs that contributes to improving driver throughput and reducing
CPU load.
A pool of Rx URBs is created during driver instantiation. All the
URBs are initially submitted to the USB host controller for
processing.
The default URB buffer size is different for each USB bus speed.
The chosen sizes provide good USB utilisation with little impact on
overall packet latency.
Completed URBs are processed in the driver bottom half. The URB
buffer contents are copied to a dynamically allocated SKB, which is
then passed to the network stack. The URB is then re-submitted to
the USB host controller.
NOTE: the call to skb_copy() in rx_process() that copies the URB
contents to a new SKB is a temporary change to make this patch work
in its own right. This call will be removed when the NAPI processing
is introduced by patch 6 in this patch set.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new approach to allocating and managing
Tx URBs that contributes to improving driver throughput and reducing
CPU load.
A pool of Tx URBs is created during driver instantiation. A URB is
allocated from the pool when there is data to transmit. The URB is
released back to the pool when the data has been transmitted by the
device.
The default URB buffer size is different for each USB bus speed.
The chosen sizes provide good USB utilisation with little impact on
overall packet latency.
SKBs to be transmitted are added to a pending queue for processing.
The driver tracks the available Tx URB buffer space and copies as
much pending data as possible into each free URB. Each full URB
is then submitted to the USB host controller for transmission.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory allocation that fails to check for NULL return.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like ThinkaPad Thunderbolt 4 Dock, more Lenovo docks start to use the original
Realtek USB ethernet chip ID 0bda:8153.
Lenovo Docks always use their own IDs for usb hub, even for older Docks.
If parent hub is from Lenovo, then r8152 should try MAC passthrough.
Verified on Lenovo TBT3 dock too.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On low-effciency embedded platforms, transmission performance is poor
due to on Bulk-out with single packet.
Adding TSO feature improves the transmission performance and reduces
the number of interrupt caused by Bulk-out complete.
Reference to module, net: usb: aqc111.
Signed-off-by: Jacky Chou <jackychou@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return error code if usb_maxpacket() returns 0 in usbnet_probe()
Fixes: 397430b50a ("usbnet: sanity check for maxpacket")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211026124015.3025136-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in lan78xx_tx_bh() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org # 4.3
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
In the case of catc we need a new temporary buffer to conform
to the rules for DMA coherency. That in turn necessitates
a reworking of error handling in probe().
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Manually fix all net/usb drivers without separate maintainers.
v2: catc does DMA to the buffer, leave the conversion to Oliver
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A handful of drivers use sizeof(addr) for the size of
the address, after manually confirming the size is
indeed 6 convert them to eth_hw_addr_set().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the drivers which use single-byte netdev addresses
(netdev->addr_len == 1) use the appropriate address setting
helpers.
arcnet copies from int variables and io reads a lot, so
add a helper for arcnet drivers to use.
Similar helper could be reused for phonet and appletalk
but there isn't any good central location where we could
put it, and netdevice.h is already very crowded.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for HSI
Link: https://lore.kernel.org/r/20211012142757.4124842-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new platform_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, net;
@@
- eth_platform_get_mac_address(dev, net->dev_addr)
+ platform_get_ethdev_address(dev, net)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert usb drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
Manually checked these are either usbnet or pure etherdevs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the situation that the disconnect event comes very late when the
device is unplugged, the driver would resubmit the RX bulk transfer
after getting the callback with -EPROTO immediately and continually.
Finally, soft lockup occurs.
This patch avoids to resubmit RX immediately. It uses a workqueue to
schedule the RX NAPI. And the NAPI would resubmit the RX. It let the
disconnect event have opportunity to stop the submission before soft
lockup.
Reported-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Tested-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Convert net/usb from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Convert usb drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 05b35e7eb9 ("smsc95xx: add phylib support"), link changes
are no longer propagated to usbnet. As a result, rx URB allocation won't
happen until there is a packet sent out first (this might never happen,
e.g. running just ssh server with a static IP). Fix by triggering usbnet
EVENT_LINK_CHANGE.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
If resource allocation and registration fail for a muxed tty device
(e.g. if there are no more minor numbers) the driver should not try to
deregister the never-registered (or already-deregistered) tty.
Fix up the error handling to avoid dereferencing a NULL pointer when
attempting to remove the character device.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL
address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmE3uicACgkQMUZtbf5S
IrtJVA//XdE8qAmw1JukjyYC87JH2ale20eoZ6ERn7/09e4tdv3M6dOTI4YfrM6+
CMNP5MP2qit3IzY+lN0+yt9AAFH7k85z3MA8zLxsXN4z63OJcZvFv/G/OWy4Wp/0
vOo/DH+rF3LR+fZZvjJI+8Xi9/orsRpD12cwGmjGRxybh+XcnHKI/GvK2RgE6oBR
015RfBbbQBpzFQvESLnSwDzabN1XFEL1x/bz7N8ek3okfO/tab+f3E1tb6eYtTy+
jyDyOWpayd4xDttKNMUuxwS1q+/oAWOAq8PzkaF/ZG2sBH1Z4yZN9ZtsLNZmPG8N
5L1FEem/Nmgr54T9v/FhfiryhhGGysVfVgtQcCBkKRmVn1Kk2L6dFvtuanPtFFd3
llbi5PvCDJy3rbMmxKmyoM3T4jpMwWxQRZKsosw+k/WQfb8/SUOjgpY713V1Wx/P
S+2uadU4l9Ql9sF6X0IqZABnnt+j/BuDo6C6vVq7vyj0iQ9hEX9YxC0ybrAHOYpH
suHWKndodRfTxxVOg8xRNYwXyRLNbm1AP6LMDNKBlFUjwNSZ362qFX7W7DuXoRup
Rrnb8V1QFvM+pyFb2a0qNtBS68IXbjCdVQX5e8a5ELaAUnDPefNrfPN+/rrTLEtV
LnusmBF+02llVSYdr88t1e+LmzqS/aqXFy2ry4y6owjq20ld2O0=
=Zvuz
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes and stragglers from Jakub Kicinski:
"Networking stragglers and fixes, including changes from netfilter,
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable
BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing
v6LL address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx
descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address"
* tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
ieee802154: Remove redundant initialization of variable ret
net: stmmac: fix MAC not working when system resume back with WoL active
net: phylink: add suspend/resume support
net: renesas: sh_eth: Fix freeing wrong tx descriptor
bonding: 3ad: pass parameter bond_params by reference
cxgb3: fix oops on module removal
can: c_can: fix null-ptr-deref on ioctl()
can: rcar_canfd: add __maybe_unused annotation to silence warning
net: wwan: iosm: Unify IO accessors used in the driver
net: wwan: iosm: Replace io.*64_lo_hi() with regular accessors
net: qcom/emac: Replace strlcpy with strscpy
ip6_gre: Revert "ip6_gre: add validation for csum_start"
net: hns3: make hclgevf_cmd_caps_bit_map0 and hclge_cmd_caps_bit_map0 static
selftests/bpf: Test XDP bonding nest and unwind
bonding: Fix negative jump label count on nested bonding
MAINTAINERS: add VM SOCKETS (AF_VSOCK) entry
stmmac: dwmac-loongson:Fix missing return value
iwlwifi: fix printk format warnings in uefi.c
net: create netdev->dev_addr assignment helpers
bnxt_en: Fix possible unintended driver initiated error recovery
...
This patch adds support for Telit LN920 0x1060 composition
0x1060: tty, adb, rmnet, tty, tty, tty, tty
Signed-off-by: Carlo Lobrano <c.lobrano@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920
0x1061 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the network devices connected to the system beyond
HSO_MAX_NET_DEVICES. add_net_device() in hso_create_net_device()
will be failed for the network_table is full. It will lead to
business failure which rely on network_table, for example,
hso_suspend() and hso_resume(). It will also lead to memory leak
because resource release process can not search the hso_device
object from network_table in hso_free_interface().
Add failure handler for add_net_device() in hso_create_net_device()
to solve the above problems.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more cleanups
on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9/lg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZNwCggKViEViSGqJFIafAZZjmI3Nt6tUAoMkRlhcd
n1MS3snS0Sq+7BdJs37M
=GyxP
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
drivers/net/usb/asix_devices.c:757:60-65: WARNING: conversion to bool not needed here
Remove unneeded conversion to bool
Semantic patch information:
Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unneeded.
Generated by: scripts/coccinelle/misc/boolconv.cocci
Fixes: 7a141e64cf ("net: usb: asix: ax88772: move embedded PHY detection as early as possible")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210825183538.13070-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Device removal can result in a large burst of driver warning messages
(20 - 30) sent to the kernel log. Most of these are register read/write
failures.
This change limits the rate at which these messages are emitted.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a device disconnect at roughly the same time as a
deferred PHY link reset there is a race condition that can result
in a kernel lock up due to a null pointer dereference in the
driver's deferred work handling routine lan78xx_delayedwork().
The following changes fix this problem.
Add new status flag EVENT_DEV_DISCONNECT to indicate when the
device has been removed and use it to prevent operations, such as
register access, that will fail once the device is removed.
Stop processing of deferred work items when the driver's USB
disconnect handler is invoked.
Disconnect the PHY only after the network device has been
unregistered and all delayed work has been cancelled.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the interface is given an IP address while the device is
suspended (as a result of an auto-suspend event) there is a race
between lan78xx_resume() and lan78xx_open() that can result in an
exception or failure to handle incoming packets. The following
changes fix this problem.
Introduce a mutex to serialise operations in the network interface
open and stop entry points with respect to the USB driver suspend
and resume entry points.
Move Tx and Rx data path start/stop to lan78xx_start() and
lan78xx_stop() respectively and flush the packet FIFOs before
starting the Tx and Rx data paths. This prevents the MAC and FIFOs
getting out of step and delivery of malformed packets to the network
stack.
Stop processing of received packets before disconnecting the
PHY from the MAC to prevent a kernel exception caused by handling
packets after the PHY device has been removed.
Refactor device auto-suspend code to make it consistent with the
the system suspend code and make the suspend handler easier to read.
Add new code to stop wake-on-lan packets or PHY events resuming the
host or device from suspend if the device has not been opened
(typically after an IP address is assigned).
This patch is dependent on changes to lan78xx_suspend() and
lan78xx_resume() introduced in the previous patch of this patch set.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC can get out of step with the internal packet FIFOs if the
system goes to sleep when the link is active, especially at high
data rates. This can result in partial frames in the packet FIFOs
that in result in malformed frames being delivered to the host.
This occurs because the driver does not enable/disable the internal
packet FIFOs in step with the corresponding MAC data path. The
following changes fix this problem.
Update code that enables/disables the MAC receiver and transmitter
to the more general Rx and Tx data path, where the data path in each
direction consists of both the MAC function (Tx or Rx) and the
corresponding packet FIFO.
In the receive path the packet FIFO must be enabled before the MAC
receiver but disabled after the MAC receiver.
In the transmit path the opposite is true: the packet FIFO must be
enabled after the MAC transmitter but disabled before the MAC
transmitter.
The packet FIFOs can be flushed safely once the corresponding data
path is stopped.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An exception is sometimes seen when the link speed is changed
from auto-negotiation to a fixed speed, or vice versa. The
exception occurs when the MAC is reset (due to the link speed
change) at the same time as the PHY state machine is accessing
a PHY register. The following changes fix this problem.
Rework the MAC reset to ensure there is no outstanding MDIO
register transaction before the reset and then wait until the
reset is complete before allowing any further MAC register access.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many places in the driver where the return code from a
function call is captured but without a subsequent test of the
return code and appropriate action taken.
This patch adds the missing return code tests and action. In most
cases the action is an early exit from the calling function.
The function lan78xx_set_suspend() was also updated to make it
consistent with lan78xx_suspend().
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the pause frame queue from the driver. It is initialised
but not actually used.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set threshold at which flow control is triggered to 3/4 full of
the internal Rx packet FIFO to prevent packet drops at high data
rates. The new setting reduces the number of dropped UDP frames
and TCP retransmit requests especially on less capable CPUs.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove kernel timer that is not used by the driver.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix white space and code style issues identified by checkpatch.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix crash on reboot on a system with ASIX AX88178 USB adapter attached
to it:
| asix 1-1.4:1.0 eth0: unregister 'asix' usb-ci_hdrc.0-1.4, ASIX AX88178 USB 2.0 Ethernet
| 8<--- cut here ---
| Unable to handle kernel NULL pointer dereference at virtual address 0000028c
| pgd = 5ec93aee
| [0000028c] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 1 PID: 1 Comm: systemd-shutdow Not tainted 5.14.0-rc1-20210811-1 #4
| Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
| PC is at phy_disconnect+0x8/0x48
| LR is at ax88772_unbind+0x14/0x20
| [<80650d04>] (phy_disconnect) from [<80741aa4>] (ax88772_unbind+0x14/0x20)
| [<80741aa4>] (ax88772_unbind) from [<8074e250>] (usbnet_disconnect+0x48/0xd8)
| [<8074e250>] (usbnet_disconnect) from [<807655e0>] (usb_unbind_interface+0x78/0x25c)
| [<807655e0>] (usb_unbind_interface) from [<805b03a0>] (__device_release_driver+0x154/0x20c)
| [<805b03a0>] (__device_release_driver) from [<805b0478>] (device_release_driver+0x20/0x2c)
| [<805b0478>] (device_release_driver) from [<805af944>] (bus_remove_device+0xcc/0xf8)
| [<805af944>] (bus_remove_device) from [<805ab26c>] (device_del+0x178/0x4b0)
| [<805ab26c>] (device_del) from [<807634a4>] (usb_disable_device+0xcc/0x178)
| [<807634a4>] (usb_disable_device) from [<8075a060>] (usb_disconnect+0xd8/0x238)
| [<8075a060>] (usb_disconnect) from [<8075a02c>] (usb_disconnect+0xa4/0x238)
| [<8075a02c>] (usb_disconnect) from [<8075a02c>] (usb_disconnect+0xa4/0x238)
| [<8075a02c>] (usb_disconnect) from [<80af3520>] (usb_remove_hcd+0xa0/0x198)
| [<80af3520>] (usb_remove_hcd) from [<807902e0>] (host_stop+0x38/0xa8)
| [<807902e0>] (host_stop) from [<8078d9e4>] (ci_hdrc_remove+0x3c/0x118)
| [<8078d9e4>] (ci_hdrc_remove) from [<805b27ec>] (platform_remove+0x20/0x50)
| [<805b27ec>] (platform_remove) from [<805b03a0>] (__device_release_driver+0x154/0x20c)
| [<805b03a0>] (__device_release_driver) from [<805b0478>] (device_release_driver+0x20/0x2c)
| [<805b0478>] (device_release_driver) from [<805af944>] (bus_remove_device+0xcc/0xf8)
| [<805af944>] (bus_remove_device) from [<805ab26c>] (device_del+0x178/0x4b0)
For this adapter we call ax88178_bind() and ax88772_unbind(), which is
related to different chip version and different counter part *bind()
function.
Since this chip is currently not ported to the PHYLIB, we do not need to
call phy_disconnect() here. So, to fix this crash, we need to add
ax88178_unbind().
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Robin van der Gracht <robin@protonic.nl>
Tested-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HW revisions need additional MAC configuration before the embedded PHY
can be enabled. If this is not done, we won't be able to get response
from the internal PHY.
This issue was detected on chipcode == AX_AX88772_CHIPCODE variant,
where ax88772_hw_reset() was executed with missing embd_phy flag.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
Kicinski;
- hurried up and removed redundant assignment in pegasus_open() before yet
another checker complains;
Fixes: 8a160e2e9a ("net: usb: pegasus: Check the return value of get_geristers() and friends;")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum PLA bp number of RTL8153C is 16, not 8. That is, the
bp 0 ~ 15 are at 0xfc28 ~ 0xfc46, and the bp_en is at 0xfc48.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().
Fixes: 9370f2d05a ("support request_firmware for RTL8153")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported uninit-value in asix_mdio_read(). The problem was in
missing error handling. asix_read_cmd() should initialize passed stack
variable smsr, but it can fail in some cases. Then while condidition
checks possibly uninit smsr variable.
Since smsr is uninitialized stack variable, driver can misbehave,
because smsr will be random in case of asix_read_cmd() failure.
Fix it by adding error handling and just continue the loop instead of
checking uninit value.
Added helper function for checking Host_En bit, since wrong loop was used
in 4 functions and there is no need in copy-pasting code parts.
Cc: Robert Foss <robert.foss@collabora.com>
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-by: syzbot+a631ec9e717fb0423053@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Fail log:
BUG: KMSAN: uninit-value in get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
BUG: KMSAN: uninit-value in pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
CPU: 1 PID: 825 Comm: kworker/1:1 Not tainted 5.12.0-rc6-syzkaller #0
...
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x24c/0x2e0 lib/dump_stack.c:120
kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x5c/0xa0 mm/kmsan/kmsan_instr.c:197
get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
....
Local variable ----data.i@pegasus_probe created at:
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
Reported-and-tested-by: syzbot+02c9f70f3afae308464a@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210804143005.439-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.
[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are now deemed redundant.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain call sites of get_geristers() did not do proper error handling. This
could be a problem as get_geristers() typically return the data via pointer to a
buffer. If an error occurred the code is carelessly manipulating the wrong data.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Reviewed-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy().
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pegasus and rtl8150 drivers use SIOCDEVPRIVATE ioctls
to access their MII registers, in place of the normal
commands. This is broken for all compat ioctls today.
Change to ndo_siocdevprivate to fix it.
Cc: Petko Manolov <petkan@nucleusys.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
phonet has a single private ioctl that is broken in compat
mode on big-endian machines today because the data returned
from it is never copied back to user space.
Move it over to the ndo_siocdevprivate callback, which also
fixes the compat issue.
Cc: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rémi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68e (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asix_get_phyid() is used for two reasons here. To print debug message
with the PHY ID and to wait until the PHY is powered up.
After migrating to the phylib, we can read PHYID from sysfs. If polling
for the PHY is really needed, then we will need to handle it in the
phylib as well.
This change was tested with:
- ax88772a + internal PHY
- ax88772b + external PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two invocation sites of hso_free_net_device. After
refactoring hso_create_net_device, this parameter is useless.
Remove the bailout in the hso_free_net_device and change the invocation
sites of this function.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current error handling code of hso_create_net_device is
hso_free_net_device, no matter which errors lead to. For example,
WARNING in hso_free_net_device [1].
Fix this by refactoring the error handling code of
hso_create_net_device by handling different errors by different code.
[1] https://syzkaller.appspot.com/bug?id=66eff8d49af1b28370ad342787413e35bbe76efe
Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com
Fixes: 5fcfb6d0bf ("hso: fix bailout in error case of probe")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current error handling code of hso_create_net_device is
hso_free_net_device, no matter which errors lead to. For example,
WARNING in hso_free_net_device [1].
Fix this by refactoring the error handling code of
hso_create_net_device by handling different errors by different code.
[1] https://syzkaller.appspot.com/bug?id=66eff8d49af1b28370ad342787413e35bbe76efe
Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com
Fixes: 5fcfb6d0bf ("hso: fix bailout in error case of probe")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 driver sets up the MAC address at reset-resume, while
rtl8152_set_mac_address() has the temporary autopm get/put. This may
lead to a deadlock as the PM lock has been already taken for the
execution of the runtime PM callback.
This patch adds the workaround to avoid the superfluous autpm when
called from rtl8152_reset_resume().
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8152_close() takes the refcount via usb_autopm_get_interface() but
it doesn't release when RTL8152_UNPLUG test hits. This may lead to
the imbalance of PM refcount. This patch addresses it.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets
in subflow receive buffers longer than necessary, delaying
MPTCP-level ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack: do not renew entry stuck in tcp SYN_SENT state
- netfilter: conntrack: do not mark RST in the reply direction coming
after SYN packet for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison
-----BEGIN PGP SIGNATURE-----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=QFnb
-----END PGP SIGNATURE-----
Merge tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski.
"Including fixes from bpf and netfilter.
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets in
subflow receive buffers longer than necessary, delaying MPTCP-level
ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack:
- do not renew entry stuck in tcp SYN_SENT state
- do not mark RST in the reply direction coming after SYN packet
for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison"
* tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (158 commits)
net: dsa: properly check for the bridge_leave methods in dsa_switch_bridge_leave()
sfc: add logs explaining XDP_TX/REDIRECT is not available
sfc: ensure correct number of XDP queues
sfc: fix lack of XDP TX queues - error XDP TX failed (-22)
net: fddi: fix UAF in fza_probe
net: dsa: sja1105: fix address learning getting disabled on the CPU port
net: ocelot: fix switchdev objects synced for wrong netdev with LAG offload
net: Use nlmsg_unicast() instead of netlink_unicast()
octeontx2-pf: Fix uninitialized boolean variable pps
ipv6: allocate enough headroom in ip6_finish_output2()
net: hdlc: rename 'mod_init' & 'mod_exit' functions to be module-specific
net: bridge: multicast: fix MRD advertisement router port marking race
net: bridge: multicast: fix PIM hello router port marking race
net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340
dsa: fix for_each_child.cocci warnings
virtio_net: check virtqueue_add_sgs() return value
mptcp: properly account bulk freed memory
selftests: mptcp: fix case multiple subflows limited by server
mptcp: avoid processing packet if a subflow reset
mptcp: fix syncookie process if mptcp can not_accept new subflow
...
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
After probe/bind sequence is the PHY in active state, even if interface
is stopped. As result, on some systems like Samsung Exynos5250 SoC based Arndale
board, the ASIX PHY will be able to negotiate the link but fail to
transmit the data.
To handle it, suspend the PHY on probe.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the netdev_dbg content from int to char * in usbnet_defer_kevent(),
this looks more readable.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Store the information of the pipes to avoid calling usb_rcvctrlpipe(),
usb_sndctrlpipe(), usb_rcvbulkpipe(), usb_sndbulkpipe(), and
usb_rcvintpipe() frequently.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when usbnet transmit a skb, eem fixup it in eem_tx_fixup(),
if skb_copy_expand() failed, it return NULL,
usbnet_start_xmit() will have no chance to free original skb.
fix it by free orginal skb in eem_tx_fixup() first,
then check skb clone status, if failed, return NULL to usbnet.
Fixes: 9f722c0978 ("usbnet: CDC EEM support (v5)")
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 46a8b29c63 ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].
This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL.
Fixes: 46a8b29c63 ("net: usb: fix memory leak in smsc75xx_bind")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the QMI_WWAN_FLAG_PASS_THROUGH is set, netif_rx() is called from
qmi_wwan_rx_fixup(). When the call to netif_rx() is successful (which is
most of the time), usbnet_skb_return() is called (from rx_process()).
usbnet_skb_return() will then call netif_rx() a second time for the same
skb.
Simplify the code and avoid the redundant netif_rx() call by changing
qmi_wwan_rx_fixup() to always return 1 when QMI_WWAN_FLAG_PASS_THROUGH
is set. We then leave it up to the existing infrastructure to call
netif_rx().
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is meant to make the host side cdc_ncm interface consistently
named just like the older CDC protocols: cdc_ether & cdc_ecm
(and even rndis_host), which all use 'FLAG_ETHER | FLAG_POINTTOPOINT'.
include/linux/usb/usbnet.h:
#define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */
#define FLAG_WLAN 0x0080 /* use "wlan%d" names */
#define FLAG_WWAN 0x0400 /* use "wwan%d" names */
#define FLAG_POINTTOPOINT 0x1000 /* possibly use "usb%d" names */
drivers/net/usb/usbnet.c @ line 1711:
strcpy (net->name, "usb%d");
...
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strcpy (net->name, "eth%d");
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strcpy(net->name, "wlan%d");
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strcpy(net->name, "wwan%d");
So by using ETHER | POINTTOPOINT the interface naming is
either usb%d or eth%d based on the global uniqueness of the
mac address of the device.
Without this 2.5gbps ethernet dongles which all seem to use the cdc_ncm
driver end up being called usb%d instead of eth%d even though they're
definitely not two-host. (All 1gbps & 5gbps ethernet usb dongles I've
tested don't hit this problem due to use of different drivers, primarily
r8152 and aqc111)
Fixes tag is based purely on git blame, and is really just here to make
sure this hits LTS branches newer than v4.5.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 4d06dd537f ("cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take over PHY power management, otherwise PHY framework will try to
access ASIX MDIO bus before MAC resume was completed.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison of the u16 priv->phy_addr < 0 is always false because
phy_addr is unsigned. Fix this by assigning the return from the call
to function asix_read_phy_addr to int ret and using this for the
less than zero error check comparison.
Fixes: 7e88b11a86 ("net: usb: asix: refactor asix_read_phy_addr() and handle errors on return")
Addresses-Coverity: ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison of the u16 priv->phy_addr < 0 is always false because
phy_addr is unsigned. Fix this by assigning the return from the call
to function asix_read_phy_addr to int ret and using this for the
less than zero error check comparison.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unbind() is the proper place to disconnect PHY, but it will fail if
netdev is already unregistered.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This usb devices can be removed at any time, so we need to forward
correct error value if device was detached.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With working phylib support we are able now to use generic selftests.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to use ax88772 with external PHYs and use advantage of
existing PHY drivers, we need to port at least ax88772 part of asix
driver to the phylib framework.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for build-in x88772A/C PHYs
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor asix_read_phy_addr() to return usable error value directly and
make sure all callers handle this error.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make resource management easier, use devm_kzalloc().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support get_pauseparam and set_pauseparam of ethtool_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported memory leak in smsc75xx_bind().
The problem was is non-freed memory in case of
errors after memory allocation.
backtrace:
[<ffffffff84245b62>] kmalloc include/linux/slab.h:556 [inline]
[<ffffffff84245b62>] kzalloc include/linux/slab.h:686 [inline]
[<ffffffff84245b62>] smsc75xx_bind+0x7a/0x334 drivers/net/usb/smsc75xx.c:1460
[<ffffffff82b5b2e6>] usbnet_probe+0x3b6/0xc30 drivers/net/usb/usbnet.c:1728
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Cc: stable@kernel.vger.org
Reported-and-tested-by: syzbot+b558506ba8165425fee2@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the tiocmset and rfkill requests which erroneously used
usb_rcvctrlpipe().
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify some fields of the USB descriptor to make sure the driver
could be used by the device.
Besides, remove the check of endpoint number in rtl8152_probe().
usb_find_common_endpoints() includes it.
BugLink: https://syzkaller.appspot.com/bug?id=912c9c373656996801b4de61f1e3cb326fe940aa
Reported-by: syzbot+95afd23673f5dd295c57@syzkaller.appspotmail.com
Fixes: c2198943e3 ("r8152: search the configuration of vendor mode")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_RW helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 31db0dbd72 ("net: hso: check for allocation failure in
hso_create_bulk_serial_device()") recently started returning an error
when the driver fails to allocate resources for the interrupt endpoint
and tiocmget functionality.
For consistency let's bail out from probe also if the URB allocation
fails.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx already calls skb_tx_timestamp() in its lan78xx_start_xmit().
Override .get_ts_info to also advertise this capability
(SOF_TIMESTAMPING_TX_SOFTWARE) via ethtool.
Signed-off-by: Markus Blöchl <markus.bloechl@ipetronik.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove leading spaces before tabs in Kconfig file(s) by running the
following command:
$ find drivers/net -name 'Kconfig*' | xargs sed -r -i 's/^[ ]+\t/\t/'
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current kernels, small allocations never actually fail so this
patch shouldn't affect runtime.
Originally this error handling code written with the idea that if
the "serial->tiocmget" allocation failed, then we would continue
operating instead of bailing out early. But in later years we added
an unchecked dereference on the next line.
serial->tiocmget->serial_state_notification = kzalloc();
^^^^^^^^^^^^^^^^^^
Since these allocations are never going fail in real life, this is
mostly a philosophical debate, but I think bailing out early is the
correct behavior that the user would want. And generally it's safer to
bail as soon an error happens.
Fixes: af0de1303c ("usb: hso: obey DMA rules in tiocmget")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tty_operations::chars_in_buffer is another hook which is expected to
return values >= 0. So make it explicit by the return type too -- use
unsigned int.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: David Sterba <dsterba@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WWAN framework provides a unified way to handle WWAN/modems and its
control port(s). It has initially been introduced to support MHI/PCI
modems, offering the same control protocols as the USB variants such as
MBIM, QMI, AT... The WWAN framework exposes these control protocols as
character devices, similarly to cdc-wdm, but in a bus agnostic fashion.
This change adds registration of the USB modem cdc-wdm control endpoints
to the WWAN framework as standard control ports (wwanXpY...).
Exposing cdc-wdm through WWAN framework normally maintains backward
compatibility, e.g:
$ qmicli --device-open-qmi -d /dev/wwan0p1QMI --dms-get-ids
instead of
$ qmicli --device-open-qmi -d /dev/cdc-wdm0 --dms-get-ids
However, some tools may rely on cdc-wdm driver/device name for device
detection. It is then safer to keep the 'legacy' cdc-wdm character
device to prevent any breakage. This is handled in this change by
API mutual exclusion, only one access method can be used at a time,
either cdc-wdm chardev or WWAN API.
Note that unknown channel types (other than MBIM, AT or MBIM) are not
registered to the WWAN framework.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8a12f88361 ("net: hso: fix null-ptr-deref during tty device
unregistration") fixed the racy minor allocation reported by syzbot, but
introduced an unconditional NULL-pointer dereference on every disconnect
instead.
Specifically, the serial device table must no longer be accessed after
the minor has been released by hso_serial_tty_unregister().
Fixes: 8a12f88361 ("net: hso: fix null-ptr-deref during tty device unregistration")
Cc: stable@vger.kernel.org
Cc: Anirudh Rayabharam <mail@anirudhrb.com>
Reported-by: Leonardo Antoniazzi <leoanto@aruba.it>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove DELL_TB_RX_AGG_BUG and LENOVO_MACPASSTHRU flags of rtl8152_flags.
They are only set when initializing and wouldn't be change. It is enough
to record them with variables.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine REALTEK_USB_DEVICE macro with USB_DEVICE_INTERFACE_CLASS and
USB_DEVICE_AND_INTERFACE_INFO to simply the code.
Although checkpatch.pl shows the following error, it is more readable.
ERROR: Macros with complex values should be enclosed in parentheses
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8156 support CDC NCM mode. And users could set the configuration
of the USB device between vendor and NCM mode dynamically by themselves.
That is, the driver doesn't need to set vendor mode from NCM mode.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the timeout occurs, we still have to run the following process
for releasing patch request. Otherwise, the PHY would keep no link.
Therefore, use break to stop the loop of loading firmware and
release the patch request rather than return the function directly.
Fixes: 4a51b0e8a0 ("r8152: support PHY firmware for RTL8156 series")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vendor mode is not always at config #1, so it is necessary to
set the correct configuration number.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new firmware type and method for RTL8156 series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support RTL8153C, RTL8153D, RTL8156A, and RTL8156B. The RTL8156A
and RTL8156B are the 2.5G ethernet.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different chips may have different requests when changing mtu.
Therefore, add a new help function of rtl_ops to change mtu. Besides,
reset the tx/rx after changing mtu.
Additionally, add mtu_to_size() and size_to_mtu() macros to simplify
the code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bits operations to record and check the firmware.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the maximum inter frame gap time (144ns) for speed 10M/half and
100M/half. It improves the performance for those speeds. And, there
is no effect for the other speeds.
For 10M/half and 100M/half, the fast inter frame gap time let the
device couldn't use the feature of the aggregation effectively,
because the transfer would be completed fastly. Therefore, use the
maximum value to improve the effect of the aggregation. However, you
may not feel the improvement for fast CPUs, because they compensate
for the effect of the aggregation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until very recently, the usbnet framework only had support functions
for devices which reported the link speed by explicitly querying the
PHY over a MDIO interface. However, the cdc_ether devices send
notifications when the link state or link speeds change and do not
expose the PHY (or modem) directly.
Support funtions (e.g. usbnet_get_link_ksettings_internal()) to directly
query state recorded by the cdc_ether driver were added in a previous patch.
Instead of cdc_ether spewing the link speed into the dmesg buffer,
record the link speed encoded in these notifications and tell the
usbnet framework to use the new functions to get link speed/state.
User space can now get the most recent link speed/state using ethtool.
v4: added to series since cdc_ether uses same notifications
as cdc_ncm driver.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until very recently, the usbnet framework only had support functions
for devices which reported the link speed by explicitly querying the
PHY over a MDIO interface. However, the cdc_ncm devices send
notifications when the link state or link speeds change and do not
expose the PHY (or modem) directly.
Support funtions (e.g. usbnet_get_link_ksettings_internal()) to directly
query state recorded by the cdc_ncm driver were added in a previous patch.
So instead of cdc_ncm spewing the link speed into the dmesg buffer,
record the link speed encoded in these notifications and tell the
usbnet framework to use the new functions to get link speed/state.
Link speed/state is now available via ethtool.
This is especially useful given all current RTL8156 devices emit
a connection/speed status notification every 32ms and this would
fill the dmesg buffer. This implementation replaces the one
recently submitted in de658a195e :
"net: usb: cdc_ncm: don't spew notifications"
v2: rebased on upstream
v3: changed variable names
v4: rewrote commit message
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Roland Dreier <roland@kernel.org>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old method for reporting link speed assumed a driver uses the
generic phy (mii) MDIO read/write functions. CDC devices don't
expose the phy.
Add a primitive internal version reporting back directly what
the CDC notification/status operations recorded.
v2: rebased on upstream
v3: changed names and made clear which units are used
v4: moved hunks to correct patch; rewrote commmit messages
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic functions assumed devices provided an MDIO interface (accessed
via older mii code, not phylib). This is true only for genuine ethernet.
Devices with a higher level of abstraction or based on different
technologies do not have MDIO. To support this case, first rename
the existing functions with _mii suffix.
v2: rebased on changed upstream
v3: changed names to clearly say that this does NOT use phylib
v4: moved hunks to correct patch; reworded commmit messages
Signed-off-by : Oliver Neukum <oneukum@suse.com>
Tested-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the USB host controller is EHCI, the throughput is reduced from
300Mb/s to 60Mb/s, when the rx buffer size is modified from 16K to
32K.
According to the EHCI spec, the maximum size of the qTD is 20K.
Therefore, when the driver uses more than 20K buffer, the latency
time of EHCI would be increased. And, it let the RTL8153A get worse
throughput.
However, the driver uses alloc_pages() for rx buffer, so I limit
the rx buffer to 16K rather than 20K.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205923
Fixes: ec5791c202 ("r8152: separate the rx buffer size")
Reported-by: Robert Davies <robdavies1977@gmail.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the disconnected flag before releasing the data interface in case
netdev registration fails to avoid having the disconnect callback try to
deregister the never registered netdev (and trigger a WARN_ON()).
Fixes: 87cf65601e ("USB host CDC Phonet network interface driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver data for the data interface has already been set by
usb_driver_claim_interface() so drop the subsequent redundant
assignment.
Note that this also avoids setting the driver data three times in case
of a combined interface.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errors in protocol should be logged when the driver aborts operations.
If the driver can carry on and "humor" the device, then emitting
the message as debug output level is fine.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several error paths in bind/probe code will only emit
output using dev_dbg. But if we are going to fail the
bind/probe, emit related output with "err" priority.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason for preventing the creation and removal
of qmimux network interfaces when the underlying interface
is up.
This makes qmi_wwan mux implementation more similar to the
rmnet one, simplifying userspace management of the same
logical interfaces.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Reported-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 134f98bcf1.
The r8153_mac_clk_spd() is used for RTL8153A only, because the register
table of RTL8153B is different from RTL8153A. However, this function would
be called when RTL8153B calls r8153_first_init() and r8153_enter_oob().
That causes RTL8153B becomes unstable when suspending and resuming. The
worst case may let the device stop working.
Besides, revert this commit to disable MAC clock speed down for RTL8153A.
It would avoid the known issue when enabling U1. The data of the first
control transfer may be wrong when exiting U1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some messages are before calling register_netdev(), so replace
netif_err() with dev_err().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Return error code if autosuspend_en, eee_get, or eee_set don't exist.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
U1/U2 shoued be enabled for USB 3.0 or later. The USB 2.0 doesn't
support it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For runtime resuming, the RTL8153B may be resumed from the state
of power cut, when enabling the feature of UPS. Then, the PHY
would be reset, so it is necessary to be initailized again.
Besides, the USB_U1U2_TIMER also has to be set again, so I move
it from r8153b_init() to r8153b_hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace r8153_patch_request() with rtl_phy_patch_request().
Replace r8153_pre_ram_code() with rtl_pre_ram_code().
Replace r8153_post_ram_code() with rtl_post_ram_code().
Add rtl_patch_key_set().
The new functions have an additional parameter. It is used to wait
the patch request command finished. When the PHY is resumed from
the state of power cut, the PHY is at a safe mode and the
OCP_PHY_PATCH_STAT wouldn't be updated. For this situation, it is
safe to set patch request command without waiting OCP_PHY_PATCH_STAT.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
It is unfortunate that we need to add a pointer to the driver context to
get back to the usbnet device, but the space will be reclaimed once
there are no more users of the old API left and we can remove the data
value and flag from the tasklet struct.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210130234637.26505-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass through mode is to allow packets in MAP format to be passed
on to the stack. rmnet driver can be used to process and demultiplex
these packets.
Pass through mode can be enabled when the device is in raw ip mode only.
Conversely, raw ip mode cannot be disabled when pass through mode is
enabled.
Userspace can use pass through mode in conjunction with rmnet driver
through the following steps-
1. Enable raw ip mode on qmi_wwan device
2. Enable pass through mode on qmi_wwan device
3. Create a rmnet device with qmi_wwan device as real device using netlink
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/1611560015-20034-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add qmimux interface sysfs file qmap/mux_id to show qmap id set
during the interface creation, in order to provide a method for
userspace to associate QMI control channels to network interfaces.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initialize tasklet using tasklet_init() rather than open-coding it.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8156 sends notifications about every 32ms.
Only display/log notifications when something changes.
This issue has been reported by others:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472https://lkml.org/lkml/2020/8/27/1083
...
[785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN
[785962.929954] usb 1-1: Manufacturer: Realtek
[785962.929956] usb 1-1: SerialNumber: 000000001
[785962.991755] usbcore: registered new interface driver cdc_ether
[785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15
[785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384
[785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384
[785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15
[785963.019211] usbcore: registered new interface driver cdc_ncm
[785963.023856] usbcore: registered new interface driver cdc_wdm
[785963.025461] usbcore: registered new interface driver cdc_mbim
[785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0
[785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
...
This is about 2KB per second and will overwrite all contents of a 1MB
dmesg buffer in under 10 minutes rendering them useless for debugging
many kernel problems.
This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering
the majority of those logs useless too.
When the link is up (expected state), spew amount is >2x higher:
...
[786139.600992] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.632997] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.665097] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.697100] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.729094] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.761108] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
...
Chrome OS cannot support RTL8156 until this is fixed.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20210120011208.3768105-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In general, device drivers should not be enabled by default.
Fixes: 657bc1d10b ("r8153_ecm: avoid to be prior to r8152 driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210113144309.1384615-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit enables the use of the r8153_ecm driver, introduced with
commit c1aedf015e ("net/usb/r8153_ecm: support ECM mode for
RTL8153") for the Lenovo Powered USB-C Hub (17ef:721e) based on the
Realtek RTL8153B chip.
This results in the following driver preference:
- if r8152 is available, use the r8152 driver
- if r8152 is not available, use the r8153_ecm driver
This is done to prevent the NIC from constantly sending pause frames
when the host system enters standby (fixed by using the r8152 driver
in "r8152: Add Lenovo Powered USB-C Travel Hub"), while still allowing
the device to work with the r8153_ecm driver as a fallback.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-3-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This USB-C Hub (17ef:721e) based on the Realtek RTL8153B chip used to
use the cdc_ether driver. However, using this driver, with the system
suspended the device constantly sends pause-frames as soon as the
receive buffer fills up. This causes issues with other devices, where
some Ethernet switches stop forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-2-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MSFT ActiveSync implementation requires that the size of the response for
incoming query is to be provided in the request input length. Failure to
set the input size proper results in failed request transfer, where the
ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L)
error.
Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size
of the response in order for the ActiveSync to properly respond to the
request.
Fixes: 039ee17d1b ("rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Link: https://lore.kernel.org/r/20210108095839.3335-1-andrey.zhizhikin@leica-geosystems.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When measuring the throughput (iperf3 + TCP) while routing on a
not-so-powerful device (Mediatek MT7621, 880MHz CPU), I noticed that I
achieved significantly lower speeds with QMI-based modems than for
example a USB LAN dongle. The CPU was saturated in all of my tests.
With the dongle I got ~300 Mbit/s, while I only measured ~200 Mbit/s
with the modems. All offloads, etc. were switched off for the dongle,
and I configured the modems to use QMAP (16k aggregation). The tests
with the dongle were performed in my local (gigabit) network, while the
LTE network the modems were connected to delivers 700-800 Mbit/s.
Profiling the kernel revealed the cause of the performance difference.
In qmimux_rx_fixup(), an SKB is allocated for each packet contained in
the URB. This SKB has too little headroom, causing the check in
skb_cow() (called from ip_forward()) to fail. pskb_expand_head() is then
called and the SKB is reallocated. In the output from perf, I see that a
significant amount of time is spent in pskb_expand_head() + support
functions.
In order to ensure that the SKB has enough headroom, this commit
increases the amount of memory allocated in qmimux_rx_fixup() by
LL_MAX_HEADER. The reason for using LL_MAX_HEADER and not a more
accurate value, is that we do not know the type of the outgoing network
interface. After making this change, I achieve the same throughput with
the modems as with the dongle.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20210106122403.1321180-1-kristian.evensen@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_ncm driver passes network connection notifications up to
usbnet_link_change(), which is the right place for any logging.
Remove the netdev_info() duplicating this from the driver itself.
This stops devices such as my "TRENDnet USB 10/100/1G/2.5G LAN"
(ID 20f4:e02b) adapter from spamming the kernel log with
cdc_ncm 2-2:2.0 enp0s2u2c2: network connection: connected
messages every 60 msec or so.
Signed-off-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201224032116.2453938-1-roland@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid r8153_ecm is compiled as built-in, if r8152 driver is compiled
as modules. Otherwise, the r8153_ecm would be used, even though the
device is supported by r8152 driver.
Fixes: c1aedf015e ("net/usb/r8153_ecm: support ECM mode for RTL8153")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/1394712342-15778-394-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LTE module MR400 embedded in TL-MR6400 v4 requires DTR to be set.
Signed-off-by: Filip Moc <dev@moc6.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20201117173631.GA550981@moc6.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: ca139d76b0 ("cx82310_eth: re-enable ethernet mode after router reboot")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605247627-15385-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace usbnet_get_stats64() with new identical core function
dev_get_tstats64() in all users and remove usbnet_get_stats64().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of usbnet for storing a pointer
to the per-cpu counters. This allows us to use core functionality for
statistics handling.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of qmimux_priv for storing
a pointer to the per-cpu counters. This allows us to use core
functionality for statistics handling.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support ECM mode based on cdc_ether with relative mii functions,
when CONFIG_USB_RTL8152 is not set, or the device is not supported
by r8152 driver.
Both r8152 and r8153_ecm would check the return value of
rtl8152_get_version() in porbe(). If rtl8152_get_version()
return none zero value, the r8152 is used for the device
with vendor mode. Otherwise, the r8153_ecm is used for the
device with ECM mode.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/1394712342-15778-392-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:992: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:992: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-28-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/lan78xx.c: In function ‘lan78xx_read_raw_otp’:
drivers/net/usb/lan78xx.c:825:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_write_raw_otp’:
drivers/net/usb/lan78xx.c:879:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_deferred_multicast_write’:
drivers/net/usb/lan78xx.c:1041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_update_flowcontrol’:
drivers/net/usb/lan78xx.c:1127:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_init_mac_address’:
drivers/net/usb/lan78xx.c:1666:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_link_status_change’:
drivers/net/usb/lan78xx.c:1841:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_irq_bus_sync_unlock’:
drivers/net/usb/lan78xx.c:1920:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan8835_fixup’:
drivers/net/usb/lan78xx.c:1994:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_rx_max_frame_length’:
drivers/net/usb/lan78xx.c:2192:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_change_mtu’:
drivers/net/usb/lan78xx.c:2270:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_mac_addr’:
drivers/net/usb/lan78xx.c:2299:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_features’:
drivers/net/usb/lan78xx.c:2333:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_suspend’:
drivers/net/usb/lan78xx.c:3807:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-25-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'blk_hdr' not described in 'fw_mac'
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'reserved' not described in 'fw_mac'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'reserved' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'reserved' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-23-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In set_ethernet_addr(), if get_registers() succeeds, the ethernet address
that was read must be copied over. Otherwise, a random ethernet address
must be assigned.
get_registers() returns 0 if successful, and negative error number
otherwise. However, in set_ethernet_addr(), this return value is
incorrectly checked.
Since this return value will never be equal to sizeof(node_id), a
random MAC address will always be generated and assigned to the
device; even in cases when get_registers() is successful.
Correctly modifying the condition that checks if get_registers() was
successful or not fixes this problem, and copies the ethernet address
appropriately.
Fixes: b2a0f274e3 ("net: rtl8150: Use the new usb control message API.")
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201011173030.141582-1-anant.thazhemadam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
When the router is rebooted without a power cycle, the USB device
remains connected but its configuration is reset. This results in
a non-working ethernet connection with messages like this in syslog:
usb 2-2: RX packet too long: 65535 B
Re-enable ethernet mode when receiving a packet with invalid size of
0xffff.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Obviously this driver version doesn't make sense. Go with the default
and let ethtool display the kernel version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add usb ids of the Cellient MPL200 card.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().
If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).
Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.
Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more generic eth_platform_get_mac_address() which can get a MAC
address from other than DT platform specific sources too. Check if the
obtained address is valid.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2:
If reading the MAC address from eeprom fail don't throw an error, use randomly
generated MAC instead. Either way the adapter will soldier on and the return
type of set_ethernet_addr() can be reverted to void.
v1:
Fix a bug in set_ethernet_addr() which does not take into account possible
errors (or partial reads) returned by its helpers. This can potentially lead to
writing random data into device's MAC address registers.
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old usb_control_msg() let the caller handle the error and also did not
account for partial reads. Since these are now considered harmful, move the
driver over to usb_control_msg_recv/send() calls.
Added small note about why set_registers() can't be used to substitute
set_register().
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20200927124909.16380-2-petko.manolov@konsulko.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old usb_control_msg() let the caller handle the error and also did not
account for partial reads. Since these are now considered harmful, move the
driver over to usb_control_msg_recv/send() calls.
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20200927124909.16380-3-petko.manolov@konsulko.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment above nc_vendor_write() suggests that the function could become
async so that is usable in `in_interrupt()' context or that it already is
safe to be called from such a context.
Eitherway: The function did not become async since v2.4.9.2 (2002) and it
must be not be called from `in_interrupt()' context because it sleeps on
mutltiple occations.
Remove the misleading comment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
kaweth_async_set_rx_mode() invokes kaweth_contol() and has two callers:
- kaweth_open() which is invoked from preemptible context
.
- kaweth_start_xmit() which holds a spinlock and has bottom halfs disabled.
If called from kaweth_start_xmit() kaweth_async_set_rx_mode() obviously
cannot block, which means it can't call kaweth_control(). This is detected
with an in_interrupt() check.
Replace the in_interrupt() check in kaweth_async_set_rx_mode() with an
argument which is set true by the caller if the context is safe to sleep,
otherwise false.
Now kaweth_control() is only called from preemptible context which means
there is no need for GFP_ATOMIC allocations anymore. Replace it with
usb_control_msg(). Cleanup the code a bit while at it.
Finally remove kaweth_control() since the last user is gone.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
kaweth_control() is almost the same as usb_control_msg() except for the
memory allocation mode (GFP_ATOMIC vs GFP_NOIO) and the in_interrupt()
check.
All the invocations of kaweth_control() are within the probe function in
fully preemtible context so there is no reason to use atomic allocations,
GFP_NOIO which is used by usb_control_msg() is perfectly fine.
Replace kaweth_control() invocations from probe with usb_control_msg().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the driver_info and usb ids of the AX88179 based MCT U3-A9003 USB
3.0 ethernet adapter.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the missing .stop entry in the Belkin driver_info structure.
Fixes: e20bd60bf6 ("net: usb: asix88179_178a: Add support for the Belkin B2B128")
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the driver_info and usb ids of the AX88179 based Toshiba USB 3.0
ethernet adapter.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
