Moving towards adding non-pci support for the driver, move the pci
parts out of the core into their own module. This is partly due to
the module_driver() code only being allowed once in a module and also
to avoid a number of #ifdef if we build a single file in a system
without pci support.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230907161242.67190-2-ben.dooks@codethink.co.uk
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
With devm_clk_get_enabled() the call to clk_disable_unprepare() can be
dropped from the error path and the remove callback. With
devm_pwmchip_add() pwmchip_remove() can be dropped. Then the remove
callback is empty and can go away, too.
Link: https://lore.kernel.org/r/20230718175545.3946935-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The semantic of chip_data is a bit surprising as it's cleared when
pwm_put() is called. Also there is a big overlap with the standard driver
data.
All drivers were adapted to not make use of chip_data any more, so it can
go away.
Link: https://lore.kernel.org/r/20230705080650.2353391-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of an allocation of a single u16 per channel, allocate them all in
a single chunk which greatly reduces memory fragmentation and also the
overhead to track the allocated memory. Also put the channel data in
driver data where it's cheaper to determine the address (no function call
involved, just a trivial pointer addition).
This also allows to get rid of the request and free callbacks.
The only cost is that the channel data is allocated early, and even for
unused channels.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20230705080650.2353391-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of using one allocation per capture channel, use a single one. Also
store it in driver data instead of chip data.
This has several advantages:
- driver data isn't cleared when pwm_put() is called
- Reduces memory fragmentation
Also register the pwm chip only after the per capture channel data is
initialized as the capture callback relies on this initialization and it
might be called even before pwmchip_add() returns.
It would be still better to have struct sti_pwm_compat_data and the
per-channel data struct sti_cpt_ddata in a single memory chunk, but that's
not easily possible because the number of capture channels isn't known yet
when the driver data struct is allocated.
Fixes: e926b12c61 ("pwm: Clear chip_data in pwm_put()")
Reported-by: George Stark <gnstark@sberdevices.ru>
Fixes: c97267ae83 ("pwm: sti: Add PWM capture callback")
Link: https://lore.kernel.org/r/20230705080650.2353391-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of distributing the driver's bookkeeping over 5 (i.e.
TPU_CHANNEL_MAX + 1) separately allocated memory chunks, put all together
in struct tpu_device. This reduces the number of memory allocations and
so fragmentation and maybe even the number of cache misses. Also
&tpu->tpd[pwm->hwpwm] is cheaper to evaluate than pwm_get_chip_data(pwm)
as the former is just an addition in machine code while the latter involves
a function call.
Link: https://lore.kernel.org/r/20230705080650.2353391-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of distributing the driver's bookkeeping over 3 (i.e.
LP3943_NUM_PWMS + 1) separately allocated memory chunks, put all together
in struct lp3943_pwm. This reduces the number of memory allocations and
so fragmentation and maybe even the number of cache misses. Also
&lp3943_pwm->pwm_map[pwm->hwpwm] is cheaper to evaluate than
pwm_get_chip_data(pwm) as the former is just an addition in machine code
while the latter involves a function call.
Link: https://lore.kernel.org/r/20230705080650.2353391-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Stop using chip_data which is about to go away. Instead track the
per-channel clk in struct jz4740_pwm_chip.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20230705080650.2353391-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of allocating extra data in .request() provide the needed memory
in struct samsung_pwm_chip. This reduces the number of allocations. Even
though now all 5 channel structs are allocated this is probably
outweighed by the reduced overhead to track up to 6 smaller allocations.
Link: https://lore.kernel.org/r/20230705080650.2353391-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of allocating extra data in .request() provide the needed memory
in struct berlin_pwm_chip. This reduces the number of allocations. A
side effect is that on suspend and resume the state for all four
channels is always saved and restored. This is easier (and probably
quicker) than looking up the matching pwm_device and checking its
PWMF_REQUESTED bit.
Link: https://lore.kernel.org/r/20230705080650.2353391-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver compiles just fine as a module. The parent driver's Kconfig
symbol already depends on X86 || COMPILE_TEST, so X86 can just be
dropped from the dependencies allowing compilation on other platforms
than x86.
Link: https://lore.kernel.org/r/20230804142707.412137-3-u.kleine-koenig@pengutronix.de
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of requiring each driver to care for assigning the owner member
of struct pwm_ops, handle that implicitly using a macro. Note that the
owner member has to be moved to struct pwm_chip, as the ops structure
usually lives in read-only memory and so cannot be modified.
The upside is that new low level drivers cannot forget the assignment and
save one line each. The pwm-crc driver didn't assign .owner, that's not
a problem in practice though as the driver cannot be compiled as a
module.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # Intel LPSS
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> # pwm-{bcm,brcm}*.c
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> # sun4i
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> # pwm-visconti
Acked-by: Heiko Stuebner <heiko@sntech.de> # pwm-rockchip
Acked-by: Michael Walle <michael@walle.cc> # pwm-sl28cpld
Acked-by: Neil Armstrong <neil.armstrong@linaro.org> # pwm-meson
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230804142707.412137-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most but not all pointers to driver data are already called "jz":
$ git grep 'struct jz4740_pwm_chip \*' v6.5-rc1 -- drivers/pwm/pwm-jz4740.c
v6.5-rc1:drivers/pwm/pwm-jz4740.c:static inline struct jz4740_pwm_chip *to_jz4740(struct pwm_chip *chip)
v6.5-rc1:drivers/pwm/pwm-jz4740.c:static bool jz4740_pwm_can_use_chn(struct jz4740_pwm_chip *jz,
v6.5-rc1:drivers/pwm/pwm-jz4740.c: struct jz4740_pwm_chip *jz = to_jz4740(chip);
v6.5-rc1:drivers/pwm/pwm-jz4740.c: struct jz4740_pwm_chip *jz = to_jz4740(chip);
v6.5-rc1:drivers/pwm/pwm-jz4740.c: struct jz4740_pwm_chip *jz = to_jz4740(chip);
v6.5-rc1:drivers/pwm/pwm-jz4740.c: struct jz4740_pwm_chip *jz4740 = to_jz4740(pwm->chip);
v6.5-rc1:drivers/pwm/pwm-jz4740.c: struct jz4740_pwm_chip *jz4740;
Adapt the two variables called "jz4740" to use the same name for
consistency.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Link: https://lore.kernel.org/r/20230808062608.897710-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the Microchip FPGA
PWM driver to use the new symbol.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This contains various cleanups and fixes across the board.
-----BEGIN PGP SIGNATURE-----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=kax5
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various cleanups and fixes across the board"
* tag 'pwm/for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (31 commits)
pwm: lpc32xx: Remove handling of PWM channels
pwm: atmel: Simplify using devm functions
dt-bindings: pwm: brcm,kona-pwm: convert to YAML
pwm: stmpe: Handle errors when disabling the signal
pwm: stm32: Simplify using devm_pwmchip_add()
pwm: stm32: Don't modify HW state in .remove() callback
pwm: Fix order of freeing resources in pwmchip_remove()
pwm: ntxec: Use device_set_of_node_from_dev()
pwm: ntxec: Drop a write-only variable from driver data
pwm: pxa: Don't reimplement of_device_get_match_data()
pwm: lpc18xx-sct: Simplify using devm_clk_get_enabled()
pwm: atmel-tcb: Don't track polarity in driver data
pwm: atmel-tcb: Unroll atmel_tcb_pwm_set_polarity() into only caller
pwm: atmel-tcb: Put per-channel data into driver data
pwm: atmel-tcb: Fix resource freeing in error path and remove
pwm: atmel-tcb: Harmonize resource allocation order
pwm: Drop unused #include <linux/radix-tree.h>
pwm: rz-mtu3: Fix build warning 'num_channel_ios' not described
pwm: Remove outdated documentation for pwmchip_remove()
pwm: atmel: Enable clk when pwm already enabled in bootloader
...
Because LPC32xx PWM controllers have only a single output which is
registered as the only PWM device/channel per controller, it is known in
advance that pwm->hwpwm value is always 0. On basis of this fact
simplify the code by removing operations with pwm->hwpwm, there is no
controls which require channel number as input.
Even though I wasn't aware at the time when I forward ported that patch,
this fixes a null pointer dereference as lpc32xx->chip.pwms is NULL
before devm_pwmchip_add() is called.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 3d2813fb17 ("pwm: lpc32xx: Don't modify HW state in .probe() after the PWM chip was registered")
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The new set of drivers for RZ/G2L MTU3a tries to enable compile-testing the
individual client drivers even when the MFD portion is disabled but gets it
wrong, causing a link failure when the core is in a loadable module but the
other drivers are built-in:
x86_64-linux-ld: drivers/pwm/pwm-rz-mtu3.o: in function `rz_mtu3_pwm_apply':
pwm-rz-mtu3.c:(.text+0x4bf): undefined reference to `rz_mtu3_8bit_ch_write'
x86_64-linux-ld: pwm-rz-mtu3.c:(.text+0x509): undefined reference to `rz_mtu3_disable'
arm-linux-gnueabi-ld: drivers/counter/rz-mtu3-cnt.o: in function `rz_mtu3_cascade_counts_enable_get':
rz-mtu3-cnt.c:(.text+0xbec): undefined reference to `rz_mtu3_shared_reg_read'
It seems better not to add the extra complexity here but instead just use
a normal hard dependency, so remove the #else portion in the header along
with the "|| COMPILE_TEST". This could also be fixed by having slightly more
elaborate Kconfig dependencies or using the cursed 'IS_REACHABLE()' helper,
but in practice it's already possible to compile-test all these drivers
by enabling the mtd portion.
Fixes: 254d3a7274 ("pwm: Add Renesas RZ/G2L MTU3a PWM driver")
Fixes: 0be8907359 ("counter: Add Renesas RZ/G2L MTU3a counter driver")
Fixes: 654c293e16 ("mfd: Add Renesas RZ/G2L MTU3a core driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230719090430.1925182-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
For all resources used by the driver there is a devm variant to allocate
these. This simplifies the error path in the probe callback and allows
to drop the remove callback.
While at it also use dev_err_probe() to compact returning an error.
With the remove callback gone, there is no user of driver data left, so
the call to platform_set_drvdata() can also be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Before the pwm framework implementedatomic updates (with the .apply()
callback) the .disable() callback returned void. This is still visible
in the stmpe driver which drops errors in the disable path.
Improve the driver to forward failures in stmpe_24xx_pwm_disable() to
the caller of pwm_apply_state().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_add() calls of_pwmchip_add() only after adding the chip to
pwm_chips and releasing pwm_lock. So the proper order in
pwmchip_remove() is to call of_pwmchip_remove() before taking the mutex
and removing the chip from pwm_chips. This way pwmchip_remove() releases
the resources in reverse order compared to pwmchip_add() requesting
them.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Compared to overwriting pdev->dev.of_node directly, this takes care of
reference counting. It also prevents that the parent device matches this
driver. See commit 9b22c17a3c ("of: Check 'of_node_reused' flag on
of_match_device()") for further details.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.dev is assigned in .probe() and never read. So it serves no purpose and
can be removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Apart from the return type pxa_pwm_get_id_dt() reimplements
of_device_get_match_data(). Drop the former and replace the call to it
by the latter.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
With devm_clk_get_enabled() the call to clk_disable_unprepare() can be
dropped from the error path and the remove callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
struct atmel_tcb_pwm_device::polarity is only used in atmel_tcb_pwm_enable
and atmel_tcb_pwm_disable(). These functions are only called by
atmel_tcb_pwm_apply() after the member variable was assigned to
state->polarity. So the value assigned in atmel_tcb_pwm_request() is
never used and the member can be dropped from struct atmel_tcb_pwm_device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
atmel_tcb_pwm_set_polarity() is only called once and effectively wraps
an assignment only. Replace the function call by the respective
assignment.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This simplifies the code, reduces the number of memory allocations and
pointer dereferences.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Several resources were not freed in the error path and the remove
function. Add the forgotten items.
Fixes: 34cbcd7258 ("pwm: atmel-tcb: Add sama5d2 support")
Fixes: 061f8572a3 ("pwm: atmel-tcb: Switch to new binding")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Allocate driver data as first resource in the probe function. This way it
can be used during allocation of the other resources (instead of assigning
these to local variables first and update driver data only when it's
allocated). Also as driver data is allocated using a devm function this
should happen first to have the order of freeing resources in the error
path and the remove function in reverse.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
core.c doens't use any of the symbols provided by linux/radix-tree.h
and compiles just fine without this include. So drop the #include.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Fix the below build warning:
warning: Function parameter or member 'num_channel_ios' not described
in 'rz_mtu3_channel_io_map'
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns void since some time but the documentation still
mentions the situations where it used to return an error code. Just remove
this old and now wrong text.
Fixes: 8083f58d08 ("pwm: Make pwmchip_remove() return void")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver would never call clk_enable() if the PWM channel was already
enabled in bootloader which lead to dump the warning message "the PWM
clock already disabled" when turning off the PWM channel.
Add atmel_pwm_enable_clk_if_on() in probe function to enable clock if
the PWM channel was already enabled in bootloader.
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Nearly all PWM drivers use the name "chip" for the member in the driver
struct pointing to the pwm_chip. Also all local variables and function
parameters with this type use this name. Rename the struct pwm_chip
member accordingly for consistency.
Also rename the parameter of the macro sl28cpld_pwm_from_chip to "chip".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most variables holding a pointer to a pwm_chip are called "chip" which
is also the usual name in most other PWM drivers. Rename the single
variable that have a different name to be called "chip", too, for
consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most variables holding a pointer to a pwm_chip are called "chip" which
is also the usual name in most other PWM drivers. Rename the single
variable that have a different name to be called "chip", too, for
consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most variables holding a pointer to a pwm_chip are called "chip" which
is also the usual name in most other PWM drivers. Rename the single
variable that have a different name to be called "chip", too, for
consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most variables holding a pointer to a pwm_chip are called "chip" which
is also the usual name in most other PWM drivers. Rename the two
variables that have a different name to be called "chip", too, for
consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most variables holding a pointer to a pwm_chip are called "chip" which
is also the usual name in most other PWM drivers. Rename the single
variable that have a different name to be called "chip", too, for
consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most variables holding a pointer to a pwm_chip are called "chip" which
is also the usual name in most other PWM drivers. Rename the single
variable that have a different name to be called "chip", too, for
consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In PWM drivers the variable name "chip" is usually only used for struct
pwm_chip pointers. This driver however used "chip" for its driver data
and pwm_chip pointers are named "chip", too, when there is no driver
data around and "c" otherwise. Instead use "atmel" for driver data and
always "chip" for pwm_chips.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
[thierry.reding@gmail.com: replace ddata by atmel]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most variables of type struct pwm_chip * are named "chip", there are
only three outliers called "pc". Change these three to "chip", too, for
consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There's a little bit of everything in here: we've got various
improvements and cleanups to drivers, some fixes across the board and a
bit of new hardware support.
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmSlRkwZHHRoaWVycnku
cmVkaW5nQGdtYWlsLmNvbQAKCRDdI6zXfz6zof9ZD/9PtA1GNgkM/FCJiIcIBXpx
FVFf6y+gHx50g+O7JDbfcNxS3b5rcbJQOwhxtTNR+9orkYUWuOkiUqWf8bUZuXCt
tjw7xW1LzDdLnxrarCD37T0aihYtKnKLxIQwdIEwS4nntaqJIdDdF62VDX+jdsbN
YvXN1WrMbGFq77EgjbWlHv8Bsm/T1mWPi3CNsKi33LvS4flCC1Mq28YalGUmwpZo
ZCJmUhPFwRbmaQ74yjUOa/UST18NwjQ/P6X25jiQ5Fjg8HZZH7RDJMduWQsT9520
U7I7UtHyZiJSGXonHTTvyhUK55wrrTVJHaXxufqvQQPTpEMG1rtlgGnBjvi/4fxt
vPIjWi46QCFtKzRFIaazHBiIEmbS+ahs8uSERmoBhlgynHyqe6/cZBdKwRp0kjSY
jLhSiE38ODENdbQmyEWuCQqv1yWQfRwwm1/Y5B4/GEX9TRNMFfUDPTEIYKEPxPM2
XI/FjMM+bP52t/rEPgCHL9E26tWv3SFPNYrafacLLfpol2iLdlAzp+ni3uz6Zj3H
f3d6LyKjVAPc1R3ICdrEu+YHRA7K10wlOQwWwXsg57dJmLtKY7gbIKJjmGVYZX63
od8/UUPzpF+eNHbrHFR1bAlwNO1XvPqHhPaQrqTQAV6zf3+VEovljLEGQmKz7yQP
ROWkedAsD7rwkFKzz9zulg==
=gWkY
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"There's a little bit of everything in here: we've got various
improvements and cleanups to drivers, some fixes across the board and
a bit of new hardware support"
* tag 'pwm/for-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (22 commits)
dt-bindings: pwm: convert pwm-bcm2835 bindings to YAML
pwm: Add Renesas RZ/G2L MTU3a PWM driver
pwm: mtk_disp: Fix the disable flow of disp_pwm
dt-bindings: pwm: restrict node name suffixes
pwm: pca9685: Switch i2c driver back to use .probe()
pwm: ab8500: Fix error code in probe()
MAINTAINERS: add pwm to PolarFire SoC entry
pwm: add microchip soft ip corePWM driver
pwm: sysfs: Do not apply state to already disabled PWMs
pwm: imx-tpm: force 'real_period' to be zero in suspend
pwm: meson: make full use of common clock framework
pwm: meson: don't use hdmi/video clock as mux parent
pwm: meson: switch to using struct clk_parent_data for mux parents
pwm: meson: remove not needed check in meson_pwm_calc
pwm: meson: fix handling of period/duty if greater than UINT_MAX
pwm: meson: modify and simplify calculation in meson_pwm_get_state
dt-bindings: pwm: Add R-Car V3U device tree bindings
dt-bindings: pwm: imx: add i.MX8QXP compatible
pwm: mediatek: Add support for MT7981
dt-bindings: pwm: mediatek: Add mediatek,mt7981 compatible
...
The RZ/G2L Multi-Function Timer Pulse Unit 3 (a.k.a MTU3a) uses
one counter and two match components to configure duty_cycle
and period to generate PWM output waveform.
Add basic support for RZ/G2L MTU3a PWM driver by creating separate
PWM channels for each IOs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is a flow error in the original mtk_disp_pwm_apply() function.
If this function is called when the clock is disabled, there will be a
chance to operate the disp_pwm register, resulting in disp_pwm exception.
Fix this accordingly.
Fixes: 888a623db5 ("pwm: mtk-disp: Implement atomic API .apply()")
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Fei Shao <fshao@chromium.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If the PWM is exported but not enabled, do not call pwm_class_apply_state().
First of all, in this case, period may still be unconfigured and this would
make pwm_class_apply_state() return -EINVAL, and then suspend would fail.
Second, it makes little sense to apply state onto PWM that is not enabled
before suspend.
Failing case:
"
$ echo 1 > /sys/class/pwm/pwmchip4/export
$ echo mem > /sys/power/state
...
pwm pwmchip4: PM: dpm_run_callback(): pwm_class_suspend+0x1/0xa8 returns -22
pwm pwmchip4: PM: failed to suspend: error -22
PM: Some devices failed to suspend, or early wake event detected
"
Working case:
"
$ echo 1 > /sys/class/pwm/pwmchip4/export
$ echo 100 > /sys/class/pwm/pwmchip4/pwm1/period
$ echo 10 > /sys/class/pwm/pwmchip4/pwm1/duty_cycle
$ echo mem > /sys/power/state
...
"
Do not call pwm_class_apply_state() in case the PWM is disabled
to fix this issue.
Fixes: 7fd4edc57b ("pwm: sysfs: Add suspend/resume support")
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: ef2bf4997f ("pwm: Improve args checking in pwm_apply_state()")
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
During suspend, all the tpm registers will lose values.
So the 'real_period' value of struct 'imx_tpm_pwm_chip'
should be forced to be zero to force the period update
code can be executed after system resume back.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 738a1cfec2 ("pwm: Add i.MX TPM PWM driver support")
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Newer versions of the PWM block use a core clock with external mux,
divider, and gate. These components either don't exist any longer in
the PWM block, or they are bypassed.
To minimize needed changes for supporting the new version, the internal
divider and gate should be handled by CCF too.
I didn't see a good way to split the patch, therefore it's somewhat
bigger. What it does:
- The internal mux is handled by CCF already. Register also internal
divider and gate with CCF, so that we have one representation of the
input clock: [mux] parent of [divider] parent of [gate]
- Now that CCF selects an appropriate mux parent, we don't need the
DT-provided default parent any longer. Accordingly we can also omit
setting the mux parent directly in the driver.
- Instead of manually handling the pre-div divider value, let CCF
set the input clock. Targeted input clock frequency is
0xffff * 1/period for best precision.
- For the "inverted pwm disabled" scenario target an input clock
frequency of ULONG_MAX. This ensures that the remaining low pulses
have minimum length.
I don't have hw with the old PWM block, therefore I couldn't test this
patch. With the not yet included extension for the new PWM block
(channel->clk coming directly from get_clk(external_clk)) I didn't
notice any problem. My system uses PWM for the CPU voltage regulator
and for the SDIO 32kHz clock.
Note: The clock gate in the old PWM block is permanently disabled.
This seems to indicate that it's not used by the new PWM block.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The meson_vclk code from the display driver may change the rate of the
video clock. Therefore better don't use it as pwm mux parent.
After removing this clock from the parent list pwm_gxbb_data and
pwm_g12a_ee_data are the same as pwm_meson8b_data. So we can remove
them.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
We'll use struct clk_parent_data for mux/div/gate initialization in the
follow-up patches. As a first step switch the mux from using
parent_names to clk_parent_data.
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
period >= duty implies that cnt >= duty_cnt. We verified before
that cnt <= 0xffff, therefore we can omit the check here.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
state->period/duty are of type u64, and if their value is greater than
UINT_MAX, then the cast to uint will cause problems. Fix this by
changing the type of the respective local variables to u64.
Fixes: b79c3670e1 ("pwm: meson: Don't duplicate the polarity internally")
Cc: stable@vger.kernel.org
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
I don't see a reason why we should treat the case lo < hi differently
and return 0 as period and duty_cycle. The current logic was added with
c375bcbaab ("pwm: meson: Read the full hardware state in
meson_pwm_get_state()"), Martin as original author doesn't remember why
it was implemented this way back then.
So let's handle it as normal use case and also remove the optimization
for lo == 0. I think the improved readability is worth it.
Fixes: c375bcbaab ("pwm: meson: Read the full hardware state in meson_pwm_get_state()")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM unit on MT7981 uses different register offsets than previous
MediaTek PWM units. Add support for these new offsets and add support
for PWM on MT7981 which has 3 PWM channels, one of them is typically
used for a temperature controlled fan.
While at it, also reorder pwm_mediatek_of_data entries to restore
alphabetic order.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of preparing the clk after it was requested and unpreparing in
.probe()'s error path and .remove(), use devm_clk_get_prepared() which
copes for unpreparing automatically.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use the devm_clk_get_prepared() helper function instead of hand-writing it.
It saves some line of codes.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The Arm documentation has moved to Documentation/arch/arm; update the
last remaining references to match.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for pwm
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The bulk of this is trivial conversions to the new .remove_new()
callback for drivers as part of Uwe's effort to clean that up.
Other than that a driver is added for Apple devices and various small
fixes are included for existing drivers.
Last but not least, this finally gets rid of the old pwm_request() and
pwm_free() APIs are removed since the last user was dropped in v6.3.
-----BEGIN PGP SIGNATURE-----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=slCK
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The bulk of this is trivial conversions to the new .remove_new()
callback for drivers as part of Uwe's effort to clean that up.
Other than that a driver is added for Apple devices and various small
fixes are included for existing drivers.
Last but not least, this finally gets rid of the old pwm_request() and
pwm_free() APIs are removed since the last user was dropped in v6.3"
* tag 'pwm/for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
pwm: Remove unused radix tree
pwm: Delete deprecated functions pwm_request() and pwm_free()
pwm: meson: Fix g12a ao clk81 name
pwm: meson: Fix axg ao mux parents
pwm: stm32: Enforce settings for PWM capture
MAINTAINERS: Add entries for Apple PWM driver
pwm: Add Apple PWM controller
dt-bindings: pwm: Add Apple PWM controller
pwm: mtk-disp: Configure double buffering before reading in .get_state()
pwm: mtk-disp: Disable shadow registers before setting backlight values
pwm: stm32-lp: Drop of_match_ptr for ID table
pwm: rcar: Drop of_match_ptr for ID table
dt-bindings: pwm: Convert Amlogic Meson PWM binding
dt-bindings: pwm: mediatek: Add mediatek,mt7986 compatible
pwm: xilinx: Convert to platform remove callback returning void
pwm: vt8500: Convert to platform remove callback returning void
pwm: tiehrpwm: Convert to platform remove callback returning void
pwm: tiecap: Convert to platform remove callback returning void
pwm: tegra: Convert to platform remove callback returning void
pwm: sun4i: Convert to platform remove callback returning void
...
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
The radix tree's only use was to map PWM channels to the global number
space. With that number space gone, the radix tree is now unused, so it
can simply be removed.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since commit 5a7fbe452a ("backlight: pwm_bl: Drop support for legacy PWM
probing") the last user of pwm_request() and pwm_free() is gone. So remove
these functions that were deprecated over 10 years ago in commit
8138d2ddbc ("pwm: Add table-based lookup for static mappings").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[thierry.reding@gmail.com: clean up a bit after removal]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Fix the name of the aoclk81 clock. Apparently name aoclk81 as used by
the vendor driver was changed when mainlining the g12a clock driver.
Fixes: f41efceb46 ("pwm: meson: Add clock source configuration for Meson G12A")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This fix is basically the same as 9bce02ef0d ("pwm: meson: Fix the
G12A AO clock parents order"). Vendor driver referenced there has
xtal as first parent also for axg ao. In addition fix the name
of the aoclk81 clock. Apparently name aoclk81 as used by the vendor
driver was changed when mainlining the axg clock driver.
Fixes: bccaa3f917 ("pwm: meson: Add clock source configuration for Meson-AXG")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM capture assumes that the input selector is set to default
input and that the slave mode is disabled. Force reset state for
TISEL and SMCR registers to match this requirement.
Note that slave mode disabling is not a pre-requisite by itself
for capture mode, as hardware supports it for PWM capture.
However, the current implementation of the driver does not
allow slave mode for PWM capture. Setting slave mode for PWM
capture results in wrong capture values.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The DISP_PWM controller's default behavior is to always use register
double buffering: all reads/writes are then performed on shadow
registers instead of working registers and this becomes an issue
in case our chosen configuration in Linux is different from the
default (or from the one that was pre-applied by the bootloader).
An example of broken behavior is when the controller is configured
to use shadow registers, but this driver wants to configure it
otherwise: what happens is that the .get_state() callback is called
right after registering the pwmchip and checks whether the PWM is
enabled by reading the DISP_PWM_EN register;
At this point, if shadow registers are enabled but their content
was not committed before booting Linux, we are *not* reading the
current PWM enablement status, leading to the kernel knowing that
the hardware is actually enabled when, in reality, it's not.
The aforementioned issue emerged since this driver was fixed with
commit 0b5ef3429d ("pwm: mtk-disp: Fix the parameters calculated
by the enabled flag of disp_pwm") making it to read the enablement
status from the right register.
Configure the controller in the .get_state() callback to avoid
this desync issue and get the backlight properly working again.
Fixes: 3f2b167349 ("pwm: mtk-disp: Implement atomic API .get_state()")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If shadow registers usage is not desired, disable that before performing
any write to CON0/1 registers in the .apply() callback, otherwise we may
lose clkdiv or period/width updates.
Fixes: cd4b45ac44 ("pwm: Add MediaTek MT2701 display PWM driver support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes the following compile error:
drivers/pwm/pwm-stm32-lp.c:245:34: error: ‘stm32_pwm_lp_of_match’ defined but not used [-Werror=unused-const-variable=]
for builds with CONFIG_OF=n, CONFIG_PWM_STM32_LP=y and W=1.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes the following compiler warning:
drivers/pwm/pwm-rcar.c:252:34: error: ‘rcar_pwm_of_table’ defined but not used [-Werror=unused-const-variable=]
for builds with CONFIG_OF=n, CONFIG_PWM_RCAR=y and W=1.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This is just to ensure that .usage_power is properly initialized and
doesn't contain random stack data. The other members of struct pwm_state
should get a value assigned in a successful call to .get_state(). So in
the absence of bugs in driver implementations, this is only a safe-guard
and no fix.
Reported-by: Munehisa Kamata <kamatam@amazon.com>
Link: https://lore.kernel.org/r/20230310214004.2619480-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver only supports normal polarity. Complete the implementation of
.get_state() by setting .polarity accordingly.
This fixes a regression that was possible since commit c73a310762
("pwm: Handle .get_state() failures") which stopped to zero-initialize
the state passed to the .get_state() callback. This was reported at
https://forum.odroid.com/viewtopic.php?f=177&t=46360 . While this was an
unintended side effect, the real issue is the driver's callback not
setting the polarity.
There is a complicating fact, that the .apply() callback fakes support
for inversed polarity. This is not (and cannot) be matched by
.get_state(). As fixing this isn't easy, only point it out in a comment
to prevent authors of other drivers from copying that approach.
Fixes: c375bcbaab ("pwm: meson: Read the full hardware state in meson_pwm_get_state()")
Reported-by: Munehisa Kamata <kamatam@amazon.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230310191405.2606296-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver only supports normal polarity. Complete the implementation of
.get_state() by setting .polarity accordingly.
Fixes: 6f0841a819 ("pwm: Add support for Azoteq IQS620A PWM generator")
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20230228135508.1798428-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver only both polarities. Complete the implementation of
.get_state() by setting .polarity according to the configured hardware
state.
Fixes: d09f008108 ("pwm: Add PWM driver for HiSilicon BVT SOCs")
Link: https://lore.kernel.org/r/20230228135508.1798428-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the PWM chip using devm_pwmchip_add() to avoid having to manually
remove it. This is useful for subsequent patches adding platform device
support.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In preparation for adding other bus support, move the allocation
of the PWM structure out of the main driver code.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The dwc_pwm_probe() assigns dev to be &pci->dev but then uses &pci->dev
throughout the function. Change these all to the 'dev' variable to make
lines shorter.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The call to regmap_update_bits() which was responsible for clearing
the PWM output enable register bit was recently dropped in favor of
a call to regmap_clear_bits(), thereby simplifying the code.
Similarly, the call to regmap_update_bits() which sets the same bit
can be simplified with a call to regmap_set_bits().
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The registers are readable, so it's possible to implement the
.get_state() callback for this PWM.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
After a check of the manual it becomes obvious that the calculations in
.apply() are totally bogus:
FreqPWMOutx was always written as zero, so the period was fixed at
3413333.33 ns. However state->period wasn't checked at all.
The lower 10 bits of duty_cycle were just used as DutyPWMOutx. So if
a duty cycle of 512 ns (or 1536 ns) was requested, it actually
programmed 1710000 ns. Other values were wrong by the same factor.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
lp3943 is a platform driver that doesn't use any symbol provided in
<linux/i2c.h>. So drop the include.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The ARR (auto reload register) and CMP (compare) registers are
successively written. The status bits to check the update of these
registers are polled together with regmap_read_poll_timeout().
The condition to end the loop may become true, even if one of the
register isn't correctly updated.
So ensure both status bits are set before clearing them.
Fixes: e70a540b4e ("pwm: Add STM32 LPTimer PWM driver")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Commit 2cfe9bbec5 added support for the
RGB and green PWM controlled LEDs on the HiFive Unmatched board
managed by the leds-pwm-multicolor and leds-pwm drivers respectively.
All three colours of the RGB LED and the green LED run from different
lines of the same PWM, but with the same period so this works fine when
the LED drivers are loaded one after the other.
Unfortunately it does expose a race in the PWM driver when both LED
drivers are loaded at roughly the same time. Here is an example:
| Thread A | Thread B |
| led_pwm_mc_probe | led_pwm_probe |
| devm_fwnode_pwm_get | |
| pwm_sifive_request | |
| ddata->user_count++ | |
| | devm_fwnode_pwm_get |
| | pwm_sifive_request |
| | ddata->user_count++ |
| ... | ... |
| pwm_state_apply | pwm_state_apply |
| pwm_sifive_apply | pwm_sifive_apply |
Now both calls to pwm_sifive_apply will see that ddata->approx_period,
initially 0, is different from the requested period and the clock needs
to be updated. But since ddata->user_count >= 2 both calls will fail
with -EBUSY, which will then cause both LED drivers to fail to probe.
Fix it by letting the first call to pwm_sifive_apply update the clock
even when ddata->user_count != 1.
Fixes: 9e37a53eb0 ("pwm: sifive: Add a driver for SiFive SoC PWM")
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Various changes across the board, mostly improvements and cleanups.
-----BEGIN PGP SIGNATURE-----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=IM51
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various changes across the board, mostly improvements and cleanups"
* tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (42 commits)
pwm: pca9685: Convert to i2c's .probe_new()
pwm: sun4i: Propagate errors in .get_state() to the caller
pwm: Handle .get_state() failures
pwm: sprd: Propagate errors in .get_state() to the caller
pwm: rockchip: Propagate errors in .get_state() to the caller
pwm: mtk-disp: Propagate errors in .get_state() to the caller
pwm: imx27: Propagate errors in .get_state() to the caller
pwm: cros-ec: Propagate errors in .get_state() to the caller
pwm: crc: Propagate errors in .get_state() to the caller
leds: qcom-lpg: Propagate errors in .get_state() to the caller
drm/bridge: ti-sn65dsi86: Propagate errors in .get_state() to the caller
pwm/tracing: Also record trace events for failed API calls
pwm: Make .get_state() callback return an error code
pwm: pxa: Enable for MMP platform
pwm: pxa: Add reference manual link and limitations
pwm: pxa: Use abrupt shutdown mode
pwm: pxa: Remove clk enable/disable from pxa_pwm_config
pwm: pxa: Set duty cycle to 0 when disabling PWM
pwm: pxa: Remove pxa_pwm_enable/disable
pwm: mediatek: Add support for MT7986
...
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Link: https://lore.kernel.org/r/20221118224540.619276-538-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() can return an error indication now. Make use of it to
propagate an impossible prescaler encoding, should that have sneaked in
somehow.
Also check the return value of clk_get_rate(). That's unlikely to fail,
but we use that in two divide operations down in the code, so let's
avoid a divide-by-zero condition on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221201152223.3133-1-andre.przywara@arm.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This suppresses diagnosis for PWM_DEBUG routines and makes sure that
pwm->state isn't modified in pwm_device_request() if .get_state() fails.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Record and report an error code for the events. This allows to report
about failed calls without ambiguity and so gives a more complete
picture.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PXA168, which is part of the MMP platform, also uses this driver.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221113233639.24244-7-doug@schmorgal.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add a pointer to the location of reference manuals for some of the
supported chips, and add a limitations section explaining the hardware's
PWM disable behavior.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221113233639.24244-6-doug@schmorgal.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Switch to abrupt shutdown mode in order to stop the clock as soon as
possible when PWM is disabled. This minimizes the possibility of the
clock being re-enabled while it is still in the process of turning off,
which will result in the clock ending up erroneously disabled.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221113233639.24244-5-doug@schmorgal.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Now that pxa_pwm_apply always enables the clock first, there is no need
for pxa_pwm_config to do any clock enabling/disabling.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221113233639.24244-4-doug@schmorgal.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When disabling PWM, the duty cycle needs to be set to 0. This prevents
the previous duty cycle from showing up momentarily when the clock is
re-enabled next time.
Because the clock has to be running in order to configure the duty
cycle, unconditionally enable it early in pxa_pwm_apply and account for
the correct enable count at the end.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221113233639.24244-3-doug@schmorgal.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
These functions are only acting as wrappers for clk_prepare_enable and
clk_disable_unprepare now, so remove them to simplify the driver.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221113233639.24244-2-doug@schmorgal.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for PWM on MT7986 which has 2 PWM channels, one of them is
typically used for a temperature controlled fan.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Sam Shih <sam.shih@mediatek.com>
Link: https://lore.kernel.org/r/Y1K5ym1EL8kwzQEt@makrotopia.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
list_add() just overwrites the members of the element to add (here:
chip->list) without any checks, even in the DEBUG_LIST case. So save the
effort to initialize the list.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221117211143.3817381-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
alloc_pwms() only identified a free range of IDs and this range was marked
as used only later by pwmchip_add(). Instead let alloc_pwms() already do
the marking (which makes the function actually allocating the range and so
justifies the function name). This way access to the allocated_pwms
bitfield is limited to two functions only.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221117211143.3817381-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This simplifies error handling as the need for goto error handling goes
away and at the end of the function the code can be simplified as this
code isn't used in the error case any more.
Now memory allocation and the call to of_pwmchip_add() are done without
holding the lock. Both don't access the data structures protected by
&pwm_lock.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221117211143.3817381-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To simplify validation of the used locking, document for the global pwm
mutex what it actually protects against concurrent access. Also note for
two functions modifying these that pwm_lock is held by the caller.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221117211143.3817381-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
According to MT7622 Reference Manual for Development Board v1.0 the PWM
unit found in the MT7622 SoC also comes with the PWM_CK_26M_SEL register
at offset 0x210 just like other modern MediaTek ARM64 SoCs.
And also MT7622 sets that register to 0x00000001 on reset which is
described as 'Select 26M fix CLK as BCLK' in the datasheet.
Hence set has_ck_26m_sel to true also for MT7622 which results in the
driver writing 0 to the PWM_CK_26M_SEL register which is described as
'Select bus CLK as BCLK'.
Fixes: 0c0ead7623 ("pwm: mediatek: Always use bus clock")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/Y1iF2slvSblf6bYK@makrotopia.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
lpc18xx_pwm_probe() only ensures clk_rate <= NSEC_PER_SEC, the following
reasoning is right even under this slightly lesser condition.
Fixes: 8933d30c5f ("pwm: lpc18xx: Fix period handling")
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/20221108153013.132514-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In the original mtk_disp_pwm_get_state() function wrongly uses bit 0 of
CON0 to judge if the PWM is enabled.
However that is indicated by a bit (at a machine dependent position) in
the DISP_PWM_EN register. Fix this accordingly.
Fixes: 3f2b167349 ("pwm: mtk-disp: Implement atomic API .get_state()")
Signed-off-by: xinlei lee <xinlei.lee@mediatek.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/1666172538-11652-1-git-send-email-xinlei.lee@mediatek.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As was documented in commit 0f02f491b7 ("pwm: sifive: Reduce time the
controller lock is held") a caller of pwm_sifive_update_clock() must
hold the mutex. So fix pwm_sifive_clock_notifier() to grab the lock.
While this necessity was only documented later, the race exists since
the driver was introduced.
Fixes: 9e37a53eb0 ("pwm: sifive: Add a driver for SiFive SoC PWM")
Reported-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Link: https://lore.kernel.org/r/20221018061656.1428111-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Simplify a bit the code by using regmap_set_bits() and
regmap_clear_bits() instead of regmap_update_bits() when possible.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The MACH_INGENIC Kconfig option will be selected when building a kernel
targeting Ingenic SoCs, but also when compiling a generic MIPS kernel
that happens to support Ingenic SoCs.
Therefore, if MACH_INGENIC is not set, we know that we're not even
trying to build a generic kernel that supports these SoCs, and we can
hide the options to compile the SoC-specific drivers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Ingenic SoCs all require CONFIG_OF, so there is no case where we want to
use this driver without CONFIG_OF.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The pwm_lpss_probe() uses managed resources. Show this to
the users explicitly by adding devm prefix to its name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The PWM LPSS device can be embedded in another device.
In order to enable it, allow that drivers to probe
a corresponding device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
For the sake of integrity, include headers we are the direct
user of.
Replace the inclusion of device.h by a forward declaration
of struct device plus a (cheaper) of types.h as device.h is
an expensive include (measured in compiler effort).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The MAX_PWMS definition is already being used by the PWM core.
Using the same name in the certain driver confuses people
and potentially can clash with it.
Hence, rename it by adding LPSS prefix.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The value of NSEC_PER_SEC << PWM_DUTY_WIDTH doesn't fix within a 32 bit
integer causing a build warning/error (and the value truncated):
drivers/pwm/pwm-tegra.c: In function ‘tegra_pwm_config’:
drivers/pwm/pwm-tegra.c:148:53: error: result of ‘1000000000 << 8’ requires 39 bits to represent, but ‘long int’ only has 32 bits [-Werror=shift-overflow=]
148 | required_clk_rate = DIV_ROUND_UP_ULL(NSEC_PER_SEC << PWM_DUTY_WIDTH,
| ^~
Explicitly cast to a u64 to ensure the correct result.
Fixes: cfcb68817fb3 ("pwm: tegra: Improve required rate calculation")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
When dynamically scaling the PWM clock, the function
dev_pm_opp_set_rate() may set the PWM clock to a rate that is lower than
what is required. The clock rate requested when calling
dev_pm_opp_set_rate() is the minimum clock rate that is needed to drive
the PWM to achieve the required period. Hence, if the actual clock
rate is less than the requested clock rate, then the required period
cannot be achieved and configuring the PWM fails. Fix this by
calling clk_round_rate() to check if the clock rate that will be provided
is sufficient and if not, double the required clock rate to ensure the
required period can be attained.
Fixes: 8c193f4714 ("pwm: tegra: Optimize period calculation")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
For the case where dev_pm_opp_set_rate() is called to set the PWM clock
rate, the requested rate is calculated as ...
required_clk_rate = (NSEC_PER_SEC / period_ns) << PWM_DUTY_WIDTH;
The above calculation may lead to rounding errors because the
NSEC_PER_SEC is divided by 'period_ns' before applying the
PWM_DUTY_WIDTH multiplication factor. For example, if the period is
45334ns, the above calculation yields a rate of 5646848Hz instead of
5646976Hz. Fix this by applying the multiplication factor before
dividing and using the DIV_ROUND_UP macro which yields the expected
result of 5646976Hz.
Fixes: 1d7796bdb6 ("pwm: tegra: Support dynamic clock frequency configuration")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The Rockchip and Mediatek drivers gain support for more chips and the
LPSS driver undergoes some refactoring and receives some improvements.
Other than that there are various cleanups of the core.
-----BEGIN PGP SIGNATURE-----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=zTfN
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The Rockchip and Mediatek drivers gain support for more chips and the
LPSS driver undergoes some refactoring and receives some improvements.
Other than that there are various cleanups of the core"
* tag 'pwm/for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: sysfs: Replace sprintf() with sysfs_emit()
pwm: core: Replace custom implementation of device_match_fwnode()
pwm: lpss: Add a comment to the bypass field
pwm: lpss: Make use of bits.h macros for all masks
pwm: lpss: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
pwm: lpss: Use device_get_match_data() to get device data
pwm: lpss: Move resource mapping to the glue drivers
pwm: lpss: Move exported symbols to PWM_LPSS namespace
pwm: lpss: Deduplicate board info data structures
dt-bindings: pwm: Add compatible for Mediatek MT8188
dt-bindings: pwm: rockchip: Add rockchip,rk3128-pwm
dt-bindings: pwm: rockchip: Add description for rk3588
pwm: sysfs: Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
pwm: rockchip: Convert to use dev_err_probe()
* New drivers
- Driver for MAX31760 fan speed controller
- Driver for TEXAS TPS546D24 Buck Converter
- Driver for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller
* Removed drivers
- Drop obsolete asus_wmi_ec_sensors driver
* Cleanups, affecting various drivers
- Use DEFINE_SIMPLE_DEV_PM_OPS where appropriate
- Remove forward declarations
- Move from strlcpy with unused retval to strscpy
- Make use of devm_clk_get_enabled()
- Drop devm_of_pwm_get()
* Other notable cleanup and improvements
- Support for additional USB devide ID and support for reporting
of rail mode via debugfs added to corsair-psu driver
- Support for aditional USB ID in nzxt-smart2 driver
- Support for Aquacomputer High Flow Next in aquacomputer_d5next driver
- Major cleanup of pwm-fan driver
- Major cleanup of mr75203 driver, and added support for new device revision
* Various other minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=8u0w
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for MAX31760 fan speed controller
- Driver for TEXAS TPS546D24 Buck Converter
- Driver for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller
Removed drivers:
- Drop obsolete asus_wmi_ec_sensors driver
Cleanups, affecting various drivers:
- Use DEFINE_SIMPLE_DEV_PM_OPS where appropriate
- Remove forward declarations
- Move from strlcpy with unused retval to strscpy
- Make use of devm_clk_get_enabled()
- Drop devm_of_pwm_get()
Other notable cleanup and improvements:
- Support for additional USB devide ID and support for reporting of
rail mode via debugfs added to corsair-psu driver
- Support for aditional USB ID in nzxt-smart2 driver
- Support for Aquacomputer High Flow Next in aquacomputer_d5next
driver
- Major cleanup of pwm-fan driver
- Major cleanup of mr75203 driver, and added support for new device
revision
And various other minor fixes and cleanups"
* tag 'hwmon-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (86 commits)
hwmon: (corsair-psu) add USB id of new revision of the HX1000i psu
hwmon: (pmbus/mp2888) Fix sensors readouts for MPS Multi-phase mp2888 controller
dt-bindings: hwmon: sensirion,shtc1: Clean up spelling mistakes and grammar
hwmon: (nct6683) remove unused variable in nct6683_create_attr_group
hwmon: w83627hf: Reorder symbols to get rid of a few forward declarations
hwmon: (ina3221) Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
hwmon: (w83627ehf) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp108) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp103) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp102) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (pwm-fan) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (nct6775) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max6639) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max31730) witch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max31722) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (ltc2947) Switch to EXPORT_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (lm90) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (it87) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (gpio-fan) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (adt7x10) Switch to EXPORT_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
...
While the uses in this code are unproblematic, it's generally safer for
sysfs outputs to use the new sysfs_emit() helper instead of raw calls to
sprintf() and friends. This also has the benefit of annotating the uses,
which makes them easier to audit and potentially use them to generate
sysfs documentation from them.
This patch replaces existing sprintf() calls straightforwardly with the
new helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Replace custom implementation of the device_match_fwnode(). This hides
the implementation details and makes future changes easier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add a comment to the bypass field based on the commit b997e3edca
("pwm: lpss: Set enable-bit before waiting for update-bit
to go low").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Make use of the GENMASK() (far less error-prone, far more concise).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Using these new macros allows the compiler to remove the unused dev_pm_ops
structure and related functions if !CONFIG_PM without the need to mark
the functions __maybe_unused.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
device_get_match_data() in ACPI case calls similar to the
acpi_match_device(). We may simplify the code and make it
generic by replacing the latter with the former.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Move resource mapping to the glue drivers which helps
to transform pwm_lpss_probe() to pure library function
that may be used by others without need of specific
resource management.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Avoid unnecessary pollution of the global symbol namespace by
moving library functions in to a specific namespace and import
that into the drivers that make use of the functions.
For more info: https://lwn.net/Articles/760045/
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Move the board info structures from the glue drivers to the
common library and hence deduplicate configuration data.
For the Intel Braswell case the ACPI version should be used.
Because switch to ACPI/PCI is done in BIOS while quite likely
the rest of AML code is the same, meaning similar issue might
be observed. There is no bug report due to no PCI enabled device
in the wild, Andy thinks, and only reference boards can be tested,
so nobody really cares about Intel Braswell PCI case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There are no users outside of PWM core of the of_pwm_get().
Make it static.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220826172642.16404-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The devm_of_pwm_get() has recently lost its single user, drop
the dead API as well.
Note, the new code should use either plain pwm_get() or managed
devm_pwm_get() or devm_fwnode_pwm_get() APIs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220826172642.16404-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
The calculation:
val = (u64)NSEC_PER_SEC * LPC18XX_PWM_TIMER_MAX;
do_div(val, lpc18xx_pwm->clk_rate);
lpc18xx_pwm->max_period_ns = val;
is bogus because with NSEC_PER_SEC = 1000000000,
LPC18XX_PWM_TIMER_MAX = 0xffffffff and clk_rate < NSEC_PER_SEC this
overflows the (on lpc18xx (i.e. ARM32) 32 bit wide) unsigned int
.max_period_ns. This results (dependant of the actual clk rate) in an
arbitrary limitation of the maximal period. E.g. for clkrate =
333333333 (Hz) we get max_period_ns = 9 instead of 12884901897.
So make .max_period_ns an u64 and pass period and duty as u64 to not
discard relevant digits. And also make use of mul_u64_u64_div_u64()
which prevents all overflows assuming clk_rate < NSEC_PER_SEC.
Fixes: 841e6f90bb ("pwm: NXP LPC18xx PWM/SCT driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This has various upsides:
- It emits the symbolic name of the error code
- It is silent in the EPROBE_DEFER case and properly sets the defer reason
- It reduces the number of code lines slightly
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
I found these just from reading the reference manual and the driver
source. It's unclear to me if there are glitches when updating the ON
and OFF registers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Some systems have clocks exposed to external devices. If the clock
controller supports duty-cycle configuration, such clocks can be used as
pwm outputs. In fact PWM and CLK subsystems are interfaced with in a
similar way and an "opposite" driver already exists (clk-pwm). Add a
driver that would enable pwm devices to be used via clk subsystem.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWMs are expected to be functional until pwmchip_remove() is called.
So disable the clks only afterwards.
Fixes: 9e37a53eb0 ("pwm: sifive: Add a driver for SiFive SoC PWM")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.apply() assumes the clk to be for a given PWM iff the PWM is enabled.
So make sure this is the case when .probe() completes. And in .remove()
disable the according number of times.
This fixes a clk enable/disable imbalance, if some PWMs are already running
at probe time.
Fixes: 9e37a53eb0 (pwm: sifive: Add a driver for SiFive SoC PWM)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The clk is necessary for both register access and (enabled) operation of
the PWM. Instead of
clk_enable()
update_hw()
if pwm_got_enabled():
clk_enable()
elif pwm_got_disabled():
clk_disable()
clk_disable()
which is some cases only calls clk_enable() to immediately afterwards
call clk_disable again, do:
if (!prev_state.enabled)
clk_enable()
# clk enabled exactly once
update_hw()
if (!next_state.enabled)
clk_disable()
which is much easier.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
For the period check and the initial calculations of register values there
is no hardware access needed. So delay enabling the clk a bit to simplify
the code flow a bit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The lock is only to serialize access and update to user_count and
approx_period between different PWMs served by the same pwm_chip.
So the lock needs only to be taken during the check if the (chip global)
period can and/or needs to be changed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is only a single caller of pwm_sifive_enable() which only enables
or disables the clk. Put this implementation directly into
pwm_sifive_apply() which allows further simplification in the next
change.
There is no change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of explicitly using PWM_SIFIVE_PWMCMP0 + pwm->hwpwm *
PWM_SIFIVE_SIZE_PWMCMP for each access to one of the PWMCMP registers,
introduce a macro that takes the hwpwm id as parameter.
For the register definition using a plain 4 instead of the cpp constant
PWM_SIFIVE_SIZE_PWMCMP is easier to read, so define the offset macro
without the constant. The latter can then be dropped as there are no
users left.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Spelling mistake (triple letters) in comment. Detected with the help of
Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There are no drivers left providing the legacy callbacks. So drop
support for these.
If this commit breaks your out-of-tree pwm driver, look at e.g. commit
ec00cd5e63 ("pwm: renesas-tpu: Implement .apply() callback") for an
example of the needed conversion for your driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for EC_PWM_TYPE_DISPLAY_LIGHT and EC_PWM_TYPE_KB_LIGHT pwm
types to the PWM cros_ec_pwm driver. This allows specifying one of these
PWM channel by functionality, and let the EC firmware pick the correct
channel, thus abstracting the hardware implementation from the kernel
driver.
To use it, define the node with the "google,cros-ec-pwm-type"
compatible.
Signed-off-by: Fabio Baltieri <fabiobaltieri@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This just pushed a variant of pwm_apply_legacy() into the driver that was
slightly simplified because the driver doesn't provide a .set_polarity()
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This pushes a variant of pwm_apply_legacy into the driver that was slightly
simplified because the .set_polarity callback was a noop.
There is no change in behavior.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This just pushed a variant of pwm_apply_legacy() into the driver that was
slightly simplified because the driver doesn't provide a .set_polarity()
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This just pushed a variant of pwm_apply_legacy() into the driver that was
slightly simplified because the driver doesn't provide a .set_polarity()
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This just pushed a variant of pwm_apply_legacy() into the driver that was
slightly simplified because the driver doesn't provide a .set_polarity()
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This just pushed a variant of pwm_apply_legacy() into the driver that was
slightly simplified because the driver doesn't provide a .set_polarity()
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This just pushed a variant of pwm_apply_legacy() into the driver that was
slightly simplified because the driver doesn't provide a .set_polarity()
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The MediaTek Helio X10 MT6795 SoC has 7 PWMs: add a compatible string
to use the right match data.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Dividing by the result of a division looses precision because the result is
rounded twice. E.g. with clk_rate = 48000000 and period = 32760033 the
following numbers result:
rate = pc->clk_rate >> PWM_DUTY_WIDTH = 187500
hz = DIV_ROUND_CLOSEST_ULL(100ULL * NSEC_PER_SEC, period_ns) = 3052
rate = DIV_ROUND_CLOSEST_ULL(100ULL * rate, hz) = 6144
The exact result would be 6142.5061875 and (apart from rounding) this is
found by using a single division. As a side effect is also a tad
cheaper to calculate.
Also using clk_rate >> PWM_DUTY_WIDTH looses precision. Consider for
example clk_rate = 47999999 and period = 106667:
mul_u64_u64_div_u64(pc->clk_rate >> PWM_DUTY_WIDTH, period_ns,
NSEC_PER_SEC) = 19
mul_u64_u64_div_u64(pc->clk_rate, period_ns,
NSEC_PER_SEC << PWM_DUTY_WIDTH) = 20
(The exact result is 20.000062083332033.)
With this optimizations also switch from round-closest to round-down for
the period calculation. Given that the calculations were non-optimal for
quite some time now with variations in both directions which nobody
reported as a problem, this is the opportunity to align the driver's
behavior to the requirements of new drivers. This has several upsides:
- Implementation is easier as there are no round-nearest variants of
mul_u64_u64_div_u64().
- Requests for too small periods are now consistently refused. This was
kind of arbitrary before, where period_ns < min_period_ns was
refused, but in some cases min_period_ns isn't actually implementable
and then values between min_period_ns and the actual minimum were
rounded up to the actual minimum.
Note that the duty_cycle calculation isn't using the usual round-down
approach yet.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Dividing by the result of a division looses precision. Consider for example
clk_rate = 33000000 and period_ns = 500001. Then
clk_rate / (NSEC_PER_SEC / period_ns)
has the exact value 16500.033, but in C this evaluates to 16508. It gets
worse for even bigger values of period_ns, so with period_ns = 500000001,
the exact result is 16500000.033 while in C we get 33000000.
For that reason use
clk_rate * period_ns / NSEC_PER_SEC
instead which doesn't suffer from this problem. To ensure this doesn't
overflow add a safeguard check for clk_rate.
Note that duty > period can never happen, so the respective check can be
dropped.
Incidentally this fixes a division by zero if period_ns > NSEC_PER_SEC.
Another side effect is that values bigger than INT_MAX for period and
duty_cyle are not wrongly discarded any more.
Fixes: 99b82abb0a ("pwm: Add Renesas TPU PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The newly computed register values are intended to exactly match the
previously computed values. The main improvement is that the prescaler
is computed without a loop that involves two divisions in each step.
This uses the fact, that prescalers[i] = 1 << (2 * i).
Assuming a moderately smart compiler, the needed number of divisions for
the case where the requested period is too big, is reduced from 5 to 2.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver used "pwm" for struct tpu_pwm_device pointers. This name is
usually only used for struct pwm_device pointers which this driver calls
"_pwm". So rename to the driver data pointers to "tpd" which then allows
to drop the underscore from "_pwm".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
As pwm->state might not be updated in tpu_pwm_apply() before calling
tpu_pwm_config(), an additional parameter is needed for tpu_pwm_config()
to not change the implemented logic.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This simplifies an error path in .probe() and allows to drop the .remove()
function.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The added benefit is that the error code is mentioned in the error message
and its usage is a bit more compact than open coding it. This also
improves behaviour in case devm_clk_get() returns -EPROBE_DEFER.
While touching this code, consistently start error messages with upper
case.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
The size check for state->period is moved to .apply() to make sure that
the values of state->duty_cycle and state->period are passed to
pwm_samsung_config without change while they are discarded to int.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use if and else instead of if(A) and if (!A).
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This fixes a small issue in clps711x_get_duty() en passant: the
multiplication v * 0xf might have overflown.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The reg member of struct raspberrypi_pwm_prop is a little endian 32 bit
quantity. Explicitly convert the (native endian) value to little endian
on assignment as is already done in raspberrypi_pwm_set_property().
This fixes the following sparse warning:
drivers/pwm/pwm-raspberrypi-poe.c:69:24: warning: incorrect type in initializer (different base types)
drivers/pwm/pwm-raspberrypi-poe.c:69:24: expected restricted __le32 [usertype] reg
drivers/pwm/pwm-raspberrypi-poe.c:69:24: got unsigned int [usertype] reg
Fixes: 79caa362ea ("pwm: Add Raspberry Pi Firmware based PWM bus")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The array atmel_tcb_divisors is not supposed to be used outside of the
driver, so make it static.
This fixes a sparse warning:
drivers/pwm/pwm-atmel-tcb.c:64:10: warning: symbol 'atmel_tcb_divisors' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
Fixes: af66b3c093 ("pwm: Add LP3943 PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This adds PWM support for Xilinx LogiCORE IP AXI soft timers commonly
found on Xilinx FPGAs. At the moment clock control is very basic: we
just enable the clock during probe and pin the frequency. In the future,
someone could add support for disabling the clock when not in use.
Some common code has been specially demarcated. While currently only
used by the PWM driver, it is anticipated that it may be split off in
the future to be used by the timer driver as well.
This driver was written with reference to Xilinx DS764 for v1.03.a [1].
[1] https://www.xilinx.com/support/documentation/ip_documentation/axi_timer/v1_03_a/axi_timer_ds764.pdf
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Per-channel data is tracked using struct pwm_device::chip_data and
struct atmel_tcb_pwm_chip::pwms[]. Simplify by using the latter
consistently.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This fixes a problem that was supposed to be addressed by commit
6eefb79d6f ("pwm: sun4i: Remove erroneous else branch") - backlight
could not be switched off on some Allwinner A20. The commit was
correct, but was not a reliable fix for the problem, which was timing
related.
The real problem for the backlight switching problem was that sleeping
for a full period did not work, because delay_us is always zero.
It is zero because the period (plus 1 microsecond) is rounded down to
the next "jiffies", but the period is less than one jiffy.
On my Cubieboard 2, the period is 5ms, and 1 jiffy (at the default
HZ=100) is 10ms, so nsecs_to_jiffies(10ms+1us)=0.
The roundtrip from nanoseconds to jiffies and back to microseconds is
an unnecessary loss of precision; always rounding down (via
nsecs_to_jiffies()) then causes the breakage.
This patch eliminates this roundtrip, and directly converts from
nanoseconds to microseconds (for usleep_range()), using
DIV_ROUND_UP_ULL() to force rounding up. This way, the sleep time is
never zero, and after the sleep, we are guaranteed to be in a
different period, and the device is ready for another control command
for sure.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Basically this code did "jiffies + period - jiffies", and we can
simply eliminate the "jiffies" time stamp here.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Its value is calculated in sun4i_pwm_apply() and is used only there.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
- Remove the superfluous cast; the multiplication will yield a 64-bit
result due to the "100ULL" anyway,
- "a * (1 << b)" == "a << b".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As a cherry-on-top cleanup, make error messages clearer to read
by changing instances of "clock: XXXX failed" to a more readable
"Failed to get XXXX clock". Also add "of" to unsupported period
error.
This is purely a cosmetic change; no "real" functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Switch from devm_kcalloc to devm_kmalloc_array when allocating clk_pwms,
as this structure is being filled right after allocating it, hence
there is no need to zero it out beforehand.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use dev_err_probe() to simplify handling errors in pwm_mediatek_probe().
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The lock only protects against concurrent users of the PWM API. This is not
expected to be necessary. And if there was such an issue, this is better
handled in the PWM core instead as it affects all drivers in the same way.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The X1000 has the same TCU / PWM hardware as other Ingenic SoCs,
but it has only 5 channels.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Status quo is that variables of type struct vt8500_chip * are named
"vt8500", "chip". Because usually only struct pwm_device * variables
are named "pwm" and "chip" is usually used for variabled of type
struct pwm_chip *.
So consistently use the same and non-conflicting name "vt8500".
Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
During the driver probe, registers are not set to their POR value.
Signed-off-by: Lionel Vitte <lionel.vitte@free.fr>
Acked-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The variable timeout is being initialized with a value that is never
read, it is being re-assigned the same value later on. Remove the
redundant initialization and keep the latter assignment because it's
closer to the use of the variable.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since commit f9a8ee8c8b ("pwm: Always allocate PWM chip base ID
dynamically") there is no effect any more for assigning this variable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
The conversion wasn't quite straight forward because .config() and
.enable() were special to effectively swap their usual order. This resulted
in calculating the required values twice in some cases when
pwm_apply_state() was called. This is optimized en passant, and the order
of the callbacks is preserved without special jumping through hoops.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In all code locations but the probe function variables of type struct
stmpe_pwm * are called "stmpe_pwm". Align the name used in
stmpe_pwm_probe() accordingly. Still more as the current name "pwm" is
usually reserved for variables of type struct pwm_device *.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver never uses dev_get_drvdata() to retrieve the pwm driver data.
So drop setting it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Status quo is that variables of type struct sun4i_pwm_chip * are named
"pwm". This name is usually reserved for variabled of type struct
pwm_chip *.
So consistently use the same and non-conflicting name "sun4ichip" which
better reflects the intend
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Status quo is that variables of type struct tegra_pwm_chip * are named
"pwm", "chip" or "pc". The two formers are all not optimal because
usually only struct pwm_device * variables are named "pwm" and "chip" is
usually used for variabled of type struct pwm_chip *.
So consistently use the same and non-conflicting name "pc".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Status quo is that variables of type struct img_pwm_chip * are named
"pwm_chip", "pwm" or "chip" which are all not optimal because there is a
struct pwm_chip in the core, usually only struct pwm_device * variables are
named "pwm" and "chip" is usually used for variabled of type struct
pwm_chip *.
So consistently use the same and non-conflicting name "imgchip".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
As a side effect this improves the behaviour for big duty cycles where
max * duty_ns overflowed before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The per-channel data is available directly in the driver data struct. So
use it without making use of pwm_[gs]et_chip_data().
The relevant change introduced by this patch to lpc18xx_pwm_disable() at
the assembler level (for an arm lpc18xx_defconfig build) is:
push {r3, r4, r5, lr}
mov r4, r0
mov r0, r1
mov r5, r1
bl 0 <pwm_get_chip_data>
ldr r3, [r0, #0]
changes to
ldr r3, [r1, #8]
push {r4, lr}
add.w r3, r0, r3, lsl #2
ldr r3, [r3, #92] ; 0x5c
So this reduces stack usage, has an improved runtime behavior because of
better pipeline usage, doesn't branch to an external function and the
generated code is a bit smaller occupying less memory.
The codesize of lpc18xx_pwm_probe() is reduced by 32 bytes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Each devm allocations has an overhead of 24 bytes to store the related
struct devres_node additionally to the fragmentation of the allocator.
So allocating 16 struct lpc18xx_pwm_data (which only hold a single int)
adds quite some overhead. Instead put the per-channel data into the
driver data struct and allocate it in one go.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When a driver calls pwmchip_add() it has to be prepared to immediately
get its callbacks called. So move allocation of driver data and hardware
initialization before the call to pwmchip_add().
This fixes a potential NULL pointer exception and a race condition on
register writes.
Fixes: 841e6f90bb ("pwm: NXP LPC18xx PWM/SCT driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM core only calls the apply callback with a valid state pointer,
so don't repeat this check already done in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver tracks per-channel data via struct pwm_device::chip_data and
struct meson_pwm::channels[]. The latter holds the actual data, the former
is only a pointer to the latter. So simplify by using struct
meson_pwm::channels[] consistently.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In meson_pwm_free() the function pwm_get_chip_data() always returns a
non-NULL pointer because it's only called when the request callback
succeeded and this callback calls pwm_set_chip_data() in this case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In .request() pwm_get_chip_data() returns NULL always since commit
e926b12c61 ("pwm: Clear chip_data in pwm_put()"). (And if it didn't
returning 0 would be wrong because then .request() wouldn't reenable
the clk which the other driver code depends on.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This contains a number of nice cleanups and improvements for the core
and various drivers as well as a minor tweak to the json-schema device
tree bindings.
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmHn9jsZHHRoaWVycnku
cmVkaW5nQGdtYWlsLmNvbQAKCRDdI6zXfz6zofJxEACUZbZ7IcJoq2zQ+TbP6DPW
DN8UyT41JsvHmHwWOv1Y3LZkHFE2HN9novJWxTx9tS0aUjwizKpJpBC3up7NC9gj
67vnHdyISAqdRGsrgGkza0q2h3nA0rgz3EINj+XeCdvtU+3wCYHahaiy0hH8GSjN
XnqBOJQDLKqC3a5MGtZZ+oGUIARyCVVhbDlUrXUU+6Q71SjmjbVUtt/RjjYl0qsO
RKHR5Wz8wg6reR9eJDOST2HvYoi2Z1Zf8M+i4kSF+dwHcRzbCEu7VZLGiz8lovBO
l9+2jU/11Lqqr7a3qIw7/xeBF3WSL31QQTFaDq+hX/xWFa4fmtyvw2J68ZoLAKib
eEjx6lfrbAx/9dlfs7l0IQLsPgty/JBJE760vwDXYpQ5VqAqhCRWHPABQjpGi/nB
CSvXw1ZJrxnMUISwfkrEZxQzsKLDKBjqTaTHQ8VK8nmwjHvktE/5wfuTAIfipuj4
8JCNSX8JzfHkhATv7TBepNxJh1JEjrqeQ2abFgmRqJrGNeoN4wgRSg6OWxIiBXCj
XQNhxfmEmPguJ85XHIvMqSt8d+9o/DCdOB5y9IKGFTrAJZVBhdxw06qxTCiXasar
31mQYDCejzxVVsPRfN5q0fZXlz6Sskzcoj7fKKpsyNtik71ONxv3XPLuq5JOLuwv
Z1wMLELztSo/3AFELNi25Q==
=T47H
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a number of nice cleanups and improvements for the core
and various drivers, as well as a minor tweak to the json-schema
device tree bindings"
* tag 'pwm/for-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
dt-bindings: pwm: Avoid selecting schema on node name match
pwm: img: Use only a single idiom to get a runtime PM reference
pwm: vt8500: Implement .apply() callback
pwm: img: Implement .apply() callback
pwm: twl: Implement .apply() callback
pwm: Restore initial state if a legacy callback fails
pwm: Prevent a glitch for legacy drivers
pwm: Move legacy driver handling into a dedicated function
core:
- add privacy screen support
- move nomodeset option into drm subsystem
- clean up nomodeset handling in drivers
- make drm_irq.c legacy
- fix stack_depot name conflicts
- remove DMA_BUF_SET_NAME ioctl restrictions
- sysfs: send hotplug event
- replace several DRM_* logging macros with drm_*
- move hashtable to legacy code
- add error return from gem_create_object
- cma-helper: improve interfaces, drop CONFIG_DRM_KMS_CMA_HELPER
- kernel.h related include cleanups
- support XRGB2101010 source buffers
ttm:
- don't include drm hashtable
- stop pruning fences after wait
- documentation updates
dma-buf:
- add dma_resv selftest
- add debugfs helpers
- remove dma_resv_get_excl_unlocked
- documentation
- make fences mandatory in dma_resv_add_excl_fence
dp:
- add link training delay helpers
gem:
- link shmem/cma helpers into separate modules
- use dma_resv iteratior
- import dma-buf namespace into gem helper modules
scheduler:
- fence grab fix
- lockdep fixes
bridge:
- switch to managed MIPI DSI helpers
- register and attach during probe fixes
- convert to YAML in several places.
panel:
- add bunch of new panesl
simpledrm:
- support FB_DAMAGE_CLIPS
- support virtual screen sizes
- add Apple M1 support
amdgpu:
- enable seamless boot for DCN 3.01
- runtime PM fixes
- use drm_kms_helper_connector_hotplug_event
- get all fences at once
- use generic drm fb helpers
- PSR/DPCD/LTTPR/DSC/PM/RAS/OLED/SRIOV fixes
- add smart trace buffer (STB) for supported GPUs
- display debugfs entries
- new SMU debug option
- Documentation update
amdkfd:
- IP discovery enumeration refactor
- interface between driver fixes
- SVM fixes
- kfd uapi header to define some sysfs bitfields.
i915:
- support VESA panel backlights
- enable ADL-P by default
- add eDP privacy screen support
- add Raptor Lake S (RPL-S) support
- DG2 page table support
- lots of GuC/HuC fw refactoring
- refactored i915->gt interfaces
- CD clock squashing support
- enable 10-bit gamma support
- update ADL-P DMC fw to v2.14
- enable runtime PM autosuspend by default
- ADL-P DSI support
- per-lane DP drive settings for ICL+
- add support for pipe C/D DMC firmware
- Atomic gamma LUT updates
- remove CCS FB stride restrictions on ADL-P
- VRR platform support for display 11
- add support for display audio codec keepalive
- lots of display refactoring
- fix runtime PM handling during PXP suspend
- improved eviction performance with async TTM moves
- async VMA unbinding improvements
- VMA locking refactoring
- improved error capture robustness
- use per device iommu checks
- drop bits stealing from i915_sw_fence function ptr
- remove dma_resv_prune
- add IC cache invalidation on DG2
nouveau:
- crc fixes
- validate LUTs in atomic check
- set HDMI AVI RGB quant to full
tegra:
- buffer objects reworks for dma-buf compat
- NVDEC driver uAPI support
- power management improvements
etnaviv:
- IOMMU enabled system support
- fix > 4GB command buffer mapping
- close a DoS vector
- fix spurious GPU resets
ast:
- fix i2c initialization
rcar-du:
- DSI output support
exynos:
- replace legacy gpio interface
- implement generic GEM object mmap
msm:
- dpu plane state cleanup in prep for multirect
- dpu debugfs cleanups
- dp support for sc7280
- a506 support
- removal of struct_mutex
- remove old eDP sub-driver
anx7625:
- support MIPI DSI input
- support HDMI audio
- fix reading EDID
lvds:
- fix bridge DT bindings
megachips:
- probe both bridges before registering
dw-hdmi:
- allow interlace on bridge
ps8640:
- enable runtime PM
- support aux-bus
tx358768:
- enable reference clock
- add pulse mode support
ti-sn65dsi86:
- use regmap bulk write
- add PWM support
etnaviv:
- get all fences at once
gma500:
- gem object cleanups
kmb:
- enable fb console
radeon:
- use dma_resv_wait_timeout
rockchip:
- add DSP hold timeout
- suspend/resume fixes
- PLL clock fixes
- implement mmap in GEM object functions
- use generic fbdev emulation
sun4i:
- use CMA helpers without vmap support
vc4:
- fix HDMI-CEC hang with display is off
- power on HDMI controller while disabling
- support 4K@60Hz modes
- support 10-bit YUV 4:2:0 output
vmwgfx:
- fix leak on probe errors
- fail probing on broken hosts
- new placement for MOB page tables
- hide internal BOs from userspace
- implement GEM support
- implement GL 4.3 support
virtio:
- overflow fixes
xen:
- implement mmap as GEM object function
omapdrm:
- fix scatterlist export
- support virtual planes
mediatek:
- MT8192 support
- CMDQ refinement
-----BEGIN PGP SIGNATURE-----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=MByd
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-01-07' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Highlights are support for privacy screens found in new laptops, a
bunch of nomodeset refactoring, and i915 enables ADL-P systems by
default, while starting to add RPL-S support.
vmwgfx adds GEM and support for OpenGL 4.3 features in userspace.
Lots of internal refactorings around dma reservations, and lots of
driver refactoring as well.
Summary:
core:
- add privacy screen support
- move nomodeset option into drm subsystem
- clean up nomodeset handling in drivers
- make drm_irq.c legacy
- fix stack_depot name conflicts
- remove DMA_BUF_SET_NAME ioctl restrictions
- sysfs: send hotplug event
- replace several DRM_* logging macros with drm_*
- move hashtable to legacy code
- add error return from gem_create_object
- cma-helper: improve interfaces, drop CONFIG_DRM_KMS_CMA_HELPER
- kernel.h related include cleanups
- support XRGB2101010 source buffers
ttm:
- don't include drm hashtable
- stop pruning fences after wait
- documentation updates
dma-buf:
- add dma_resv selftest
- add debugfs helpers
- remove dma_resv_get_excl_unlocked
- documentation
- make fences mandatory in dma_resv_add_excl_fence
dp:
- add link training delay helpers
gem:
- link shmem/cma helpers into separate modules
- use dma_resv iteratior
- import dma-buf namespace into gem helper modules
scheduler:
- fence grab fix
- lockdep fixes
bridge:
- switch to managed MIPI DSI helpers
- register and attach during probe fixes
- convert to YAML in several places.
panel:
- add bunch of new panesl
simpledrm:
- support FB_DAMAGE_CLIPS
- support virtual screen sizes
- add Apple M1 support
amdgpu:
- enable seamless boot for DCN 3.01
- runtime PM fixes
- use drm_kms_helper_connector_hotplug_event
- get all fences at once
- use generic drm fb helpers
- PSR/DPCD/LTTPR/DSC/PM/RAS/OLED/SRIOV fixes
- add smart trace buffer (STB) for supported GPUs
- display debugfs entries
- new SMU debug option
- Documentation update
amdkfd:
- IP discovery enumeration refactor
- interface between driver fixes
- SVM fixes
- kfd uapi header to define some sysfs bitfields.
i915:
- support VESA panel backlights
- enable ADL-P by default
- add eDP privacy screen support
- add Raptor Lake S (RPL-S) support
- DG2 page table support
- lots of GuC/HuC fw refactoring
- refactored i915->gt interfaces
- CD clock squashing support
- enable 10-bit gamma support
- update ADL-P DMC fw to v2.14
- enable runtime PM autosuspend by default
- ADL-P DSI support
- per-lane DP drive settings for ICL+
- add support for pipe C/D DMC firmware
- Atomic gamma LUT updates
- remove CCS FB stride restrictions on ADL-P
- VRR platform support for display 11
- add support for display audio codec keepalive
- lots of display refactoring
- fix runtime PM handling during PXP suspend
- improved eviction performance with async TTM moves
- async VMA unbinding improvements
- VMA locking refactoring
- improved error capture robustness
- use per device iommu checks
- drop bits stealing from i915_sw_fence function ptr
- remove dma_resv_prune
- add IC cache invalidation on DG2
nouveau:
- crc fixes
- validate LUTs in atomic check
- set HDMI AVI RGB quant to full
tegra:
- buffer objects reworks for dma-buf compat
- NVDEC driver uAPI support
- power management improvements
etnaviv:
- IOMMU enabled system support
- fix > 4GB command buffer mapping
- close a DoS vector
- fix spurious GPU resets
ast:
- fix i2c initialization
rcar-du:
- DSI output support
exynos:
- replace legacy gpio interface
- implement generic GEM object mmap
msm:
- dpu plane state cleanup in prep for multirect
- dpu debugfs cleanups
- dp support for sc7280
- a506 support
- removal of struct_mutex
- remove old eDP sub-driver
anx7625:
- support MIPI DSI input
- support HDMI audio
- fix reading EDID
lvds:
- fix bridge DT bindings
megachips:
- probe both bridges before registering
dw-hdmi:
- allow interlace on bridge
ps8640:
- enable runtime PM
- support aux-bus
tx358768:
- enable reference clock
- add pulse mode support
ti-sn65dsi86:
- use regmap bulk write
- add PWM support
etnaviv:
- get all fences at once
gma500:
- gem object cleanups
kmb:
- enable fb console
radeon:
- use dma_resv_wait_timeout
rockchip:
- add DSP hold timeout
- suspend/resume fixes
- PLL clock fixes
- implement mmap in GEM object functions
- use generic fbdev emulation
sun4i:
- use CMA helpers without vmap support
vc4:
- fix HDMI-CEC hang with display is off
- power on HDMI controller while disabling
- support 4K@60Hz modes
- support 10-bit YUV 4:2:0 output
vmwgfx:
- fix leak on probe errors
- fail probing on broken hosts
- new placement for MOB page tables
- hide internal BOs from userspace
- implement GEM support
- implement GL 4.3 support
virtio:
- overflow fixes
xen:
- implement mmap as GEM object function
omapdrm:
- fix scatterlist export
- support virtual planes
mediatek:
- MT8192 support
- CMDQ refinement"
* tag 'drm-next-2022-01-07' of git://anongit.freedesktop.org/drm/drm: (1241 commits)
drm/amdgpu: no DC support for headless chips
drm/amd/display: fix dereference before NULL check
drm/amdgpu: always reset the asic in suspend (v2)
drm/amdgpu: put SMU into proper state on runpm suspending for BOCO capable platform
drm/amd/display: Fix the uninitialized variable in enable_stream_features()
drm/amdgpu: fix runpm documentation
amdgpu/pm: Make sysfs pm attributes as read-only for VFs
drm/amdgpu: save error count in RAS poison handler
drm/amdgpu: drop redundant semicolon
drm/amd/display: get and restore link res map
drm/amd/display: support dynamic HPO DP link encoder allocation
drm/amd/display: access hpo dp link encoder only through link resource
drm/amd/display: populate link res in both detection and validation
drm/amd/display: define link res and make it accessible to all link interfaces
drm/amd/display: 3.2.167
drm/amd/display: [FW Promotion] Release 0.0.98
drm/amd/display: Undo ODM combine
drm/amd/display: Add reg defs for DCN303
drm/amd/display: Changed pipe split policy to allow for multi-display pipe split
drm/amd/display: Set optimize_pwr_state for DCN31
...
The PWM on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now PWM must be resumed using
runtime PM API in order to initialize the PWM power state. The PWM clock
rate must be changed using OPP API that will reconfigure the power domain
performance state in accordance to the rate. Add runtime PM and OPP
support to the PWM driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently there are two very similar approaches in use by this driver:
img_pwm_config() uses pm_runtime_get_sync() and calls
pm_runtime_put_autosuspend() in the error path; img_pwm_enable() calls
pm_runtime_resume_and_get() which already puts the reference in its own
error path.
Align pm_runtime usage and use the same idiom in both locations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It is not entirely accurate to go back to the initial state after e.g.
.enable() failed, as .config() still modified the hardware, but this same
inconsistency exists for drivers that implement .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If a running PWM is reconfigured to disabled calling the ->config()
callback before disabling the hardware might result in a glitch where
the (maybe) new period and duty_cycle are visible on the output before
disabling the hardware.
So handle disabling before calling ->config(). Also exit early in this case
which is possible because period and duty_cycle don't matter for disabled PWMs.
In return however ->config has to be called even if state->period ==
pwm->state.period && state->duty_cycle != pwm->state.duty_cycle because setting
these might have been skipped in the previous call.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is no change in behaviour, only some code is moved from
pwm_apply_state to a separate function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The pwm_ prefix suggests that pwm_busy_wait() is a function provided by
the pwm core. Use the otherwise consistently used driver prefix for this
function, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When duty-cycle is at full level (100%), the TCNTn and TCMPn registers
needs to be flushed in order to disable the signal. The PWM manual does
not say anything about this, but states that only clearing the TCON
auto-reload bit should be needed, and this seems to be true when the PWM
duty-cycle is not at full level. This can be observed on an Axis
ARTPEC-8, by running:
echo <period> > pwm/period
echo <period> > pwm/duty_cycle
echo 1 > pwm/enable
echo 0 > pwm/enable
Since the TCNTn and TCMPn registers are activated when enabling the PWM
(setting TCON auto-reload bit), and are not touched when disabling the
PWM, the double buffered auto-reload function seems to be still active.
Lowering duty-cycle, and restoring it again in between the enabling and
disabling, makes the disable work since it triggers a reload of the
TCNTn and TCMPn registers.
Fix this by securing a reload of the TCNTn and TCMPn registers when
disabling the PWM and having a full duty-cycle.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: zhaoxiao <long870912@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
At least some implementations sleep. So mark pwm_apply_state() with a
might_sleep() to make callers aware. In the worst case this uncovers a
valid atomic user, then we revert this patch and at least gained some more
knowledge and then can work on a concept similar to
gpio_get_value/gpio_get_value_cansleep.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since commit 52eaba4ced ("pwm: atmel: Rework tracking updates pending
in hardware") the driver doesn't make use of mutexes any more, so the
header defining these doesn't need to be included.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The existing pxa driver and the upcoming addition of PWM support in the
TI sn565dsi86 DSI/eDP bridge driver both has a single PWM channel and
thereby a need for a of_xlate function with the period as its single
argument.
Introduce a common helper function in the core that can be used as
of_xlate by such drivers and migrate the pxa driver to use this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025170925.3096444-1-bjorn.andersson@linaro.org
Switch the driver to support the .get_state() method.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
[thierry.reding@gmail.com: add missing linux/bitfield.h include]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Current calculation for period and high_width may have 64-bit overflow.
state->period and rate are u64. rate * state->period will overflow.
clk_div = div_u64(rate * state->period, NSEC_PER_SEC)
period = div64_u64(rate * state->period, div);
high_width = div64_u64(rate * state->duty_cycle, div);
This patch is to resolve it by using mul_u64_u64_div_u64().
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Switch the driver to support the .apply() method.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The clks "main" and "mm" are prepared in .probe() (and unprepared in
.remove()). This results in the clocks being on during suspend which
results in unnecessarily increased power consumption.
Remove the clock operations from .probe() and .remove(). Add the
clk_prepare_enable() in .enable() and the clk_disable_unprepare() in
.disable().
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
[thierry.reding@gmail.com: squashed in fixup patch]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since some time pwmchip_remove() always returns 0 so the return value
isn't usefull. Now that all callers are converted to ignore its value
the function can be changed to return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of sun4i_pwm_remove()
and considers the device removed anyhow. So returning early results
in a resource leak.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of pwm_sifive_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of pwm_samsung_remove()
and considers the device removed anyhow. So returning early results
in a resource leak.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of tpu_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of rcar_pwm_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of pca9685_pwm_remove()
and considers the device removed anyhow. So returning early results
in a resource leak.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of pwm_omap_dmtimer_remove()
and considers the device removed anyhow. So returning early results
in a resource leak.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of mtk_disp_pwm_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of pwm_imx_tpm_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of pwm_imx_tpm_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of cros_ec_pwm_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of brcmstb_pwm_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of atmel_tcb_pwm_remove()
and considers the device removed anyhow. So returning early results in a
resource leak.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. Also the
driver core ignores the return value of atmel_hlcdc_pwm_remove()
and considers the device removed anyhow.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
With devm_pwmchip_add() there is no need to explicitly call
pwmchip_remove(), so this call can be dropped from the remove callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There are no arm64 specific constructs in this driver and it compiles
just fine with ARCH=arm.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There are no mips specific constructs in this driver and it compiles
just fine with ARCH=arm.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since commit f9a8ee8c8b ("pwm: Always allocate PWM chip base ID
dynamically") there is no effect any more for assigning this variable.
When the patch resulting in f9a8ee8c8b was created, this driver didn't
exist yet, so this was missed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver is supposed to stay functional until pwmchip_remove()
returns. So disable clocks only after that.
pwmchip_remove() always returns 0, so the return code can be ignored
which keeps ehrpwm_pwm_remove() a bit simpler and eventually allows to
make pwmchip_remove() return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver is supposed to stay functional until pwmchip_remove()
returns. So disable clocks only after that.
pwmchip_remove() always returns 0, so the return code can be ignored
which keeps rockchip_pwm_remove() a bit simpler and allows to eventually
make pwmchip_remove() return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver is supposed to stay functional until pwmchip_remove()
returns. So disable clocks and reset the hardware only after that.
The return value of pwmchip_remove doesn't need to be checked because
it returns zero anyhow and should be changed to return void eventually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So reset before calling pwmchip_add().
Note that reseting the hardware isn't the right thing to do if the PWM
is already running as it might e.g. disable (or even enable) a backlight
that is supposed to be on (or off).
Fixes: 4dce82c1e8 ("pwm: add pwm-mxs support")
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So set the default before.
(Side-note: I don't know what this register setting actually does, if
this modifies the polarity there is an inconsistency because the
inversed polarity isn't considered if the PWM is already running during
.probe().)
Fixes: acfd92fdfb ("pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value")
Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The assumption that lead to commit 5e5da1e9fb ("pwm: ab8500:
Explicitly allocate pwm chip base dynamically") was wrong: The
pwm-ab8500 devices are not directly instantiated from device tree, but
from the ab8500 mfd driver. So the pdev->id isn't -1, but a number
between 1 and 3. Now that pwmchip ids are always allocated dynamically,
this cannot easily be reverted.
Introduce a new member in the driver data struct that tracks the
hardware id and use this to calculate the register offset.
Side-note: Using chip->base to calculate the offset was never robust
because if there was already a PWM with id 1 at the time ab8500-pwm.1
was probed, the associated pwmchip would get assigned chip->base = 2 (or
something bigger).
Fixes: 5e5da1e9fb ("pwm: ab8500: Explicitly allocate pwm chip base dynamically")
Fixes: 6173f8f4ed ("pwm: Move AB8500 PWM driver to PWM framework")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This improves the driver's behavior in several ways:
- The lock is held for shorter periods and so a channel that is currently
waited for doesn't block disabling another channel.
- It's easier to understand because the procedure is split into more
semantic units and documentation is improved
- A channel is only set to pending when such an event is actually
scheduled in hardware (by writing the CUPD register).
- Also wait in .get_state() to report the last configured state instead
of (maybe) the previous one. This fixes the read back duty cycle and so
prevents a warning being emitted when PWM_DEBUG is on.
Tested on an AriettaG25.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As the last call to ep93xx_pwm_apply() might have exited early if
state->enabled was false, the values for period and duty_cycle stored in
pwm->state might not have been written to hardware and it must be
ensured that they are configured before enabling the PWM.
Fixes: 6d45374af5 ("pwm: ep93xx: Implement .apply callback")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As the last call to berlin_pwm_apply() might have exited early if
state->enabled was false, the values for period and duty_cycle stored in
pwm->state might not have been written to hardware and it must be
ensured that they are configured before enabling the PWM.
Fixes: 30dffb42fc ("pwm: berlin: Implement .apply() callback")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As the last call to ecap_pwm_apply() might have exited early if
state->enabled was false, the values for period and duty_cycle stored in
pwm->state might not have been written to hardware and it must be
ensured that they are configured before enabling the PWM.
Fixes: 0ca7acd847 ("pwm: tiecap: Implement .apply() callback")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As the last call to spear_pwm_apply() might have exited early if
state->enabled was false, the values for period and duty_cycle stored in
pwm->state might not have been written to hardware and it must be
ensured that they are configured before enabling the PWM.
Fixes: 98761ce4b9 ("pwm: spear: Implement .apply() callback")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As the last call to sprd_pwm_apply() might have exited early if
state->enabled was false, the values for period and duty_cycle stored in
pwm->state might not have been written to hardware and it must be
ensured that they are configured before enabling the PWM.
Fixes: 8aae4b02e8 ("pwm: sprd: Add Spreadtrum PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The pointer pwm is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is a potential path in function ep93xx_pwm_apply where ret is
never assigned a value and it is checked for an error code. Fix this
by ensuring ret is zero'd in the success path to avoid this issue.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: f6ef94edf0f6 ("pwm: ep93xx: Unfold legacy callbacks into ep93xx_pwm_apply()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use clk_prepare_enable()/clk_disable_unprepare() in preparation for switch
to Common Clock Framework.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This just puts the implementation of ep93xx_pwm_disable(),
ep93xx_pwm_enable() and ep93xx_pwm_config() into their only caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Until pwmchip_remove() returns the PWM is supposed to work, so
pwmchip_remove() must be called before the clock is stopped.
The return value of pwmchip_remove doesn't need to be checked because
it returns zero anyhow and I plan to make it return void soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
vt8500_pwm_remove() is only called after vt8500_pwm_probe() returned
successfully. In this case driver data was set to a non-NULL value
and so chip can never be NULL.
While touching this code also put declaration and assignment in a single
line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver is supposed to stay functional until pwmchip_remove()
returns. So the reset must be asserted only after that.
pwmchip_remove() always returns 0, so the return code can be ignored
which keeps the tegra_pwm_remove() a bit simpler.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is no reason to enable the PWM clock just to assert the reset
control. (If the reset control depends on the clock this is a bug and
probably it doesn't because in .probe() the reset is deasserted without
the clock being enabled.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
So drop the hardware modification from the .remove() callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
tegra_pwm_remove() is only called after tegra_pwm_probe() successfully
completed. In this case platform_set_drvdata() was called with a
non-NULL value and so platform_get_drvdata(pdev) cannot return NULL.
Returning an error code from a platform_driver's remove function is
ignored anyway, so it's a good thing this exit path is gone.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use devm_add_action_or_reset() instead of devres_alloc() and
devres_add(), which works the same. This will simplify the
code. There is no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There are no users and seems no will come of the devm_pwm_put().
Remove the function.
While at it, slightly update documentation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Historically we have two different approaches on how to check type of fwnode.
Unify them using the latest and greatest fwnode related APIs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In ACPI case we may use matching by fwnode as provided via
fwnode_to_pwmchip(). This makes device_to_pwmchip() not needed
anymore.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When we traverse the list of the registered PWM controllers,
use fwnode to match. This will help for further cleanup.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_remove() returns always 0. Don't use the value to make it
possible to eventually change the function to return void. This is a
good thing as pwmchip_remove() is usually called from a remove function
(mostly for platform devices) and their return value is ignored by the
device core anyhow.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In most functions the driver data variable is called pc. Do the same in
the two remaining functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() function is only called after .probe() returned
successfully. In this case platform_set_drvdata() was called with a
non-NULL argument and so platfrom_get_drvdata() returns the same
non-NULL value.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
