Modify driver to set the Write Same Divert Capability bit in the IOCInit
message for the firmware to know that the driver is capable of diverting
certain Write Same commands as defined by the MPI specification.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver uses a controller-wide flag to block ioctls when a controller
reset is in progress. This flag is set before controller reset is initiated
and cleared after the reset has completed.
Make the driver clear the controller-wide block ioctls flag after a
controller reset fails and the controller is marked unrecoverable.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 'flags' variable inside an MPI request is a bitfield and should
consequently be updated using a bitwise OR operation.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver did not remove the virtual disk that was exposed as hidden and
offline after the controller was reset.
Drive is removed from OS when firmware sends "device added" event with
hidden bit set or access status indicating inability to accept I/Os.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the "storcli2 show" command is executed for eHBA-9600, mpi3mr driver
prints this WARNING message:
memcpy: detected field-spanning write (size 128) of single field "bsg_reply_buf->reply_buf" at drivers/scsi/mpi3mr/mpi3mr_app.c:1658 (size 1)
WARNING: CPU: 0 PID: 12760 at drivers/scsi/mpi3mr/mpi3mr_app.c:1658 mpi3mr_bsg_request+0x6b12/0x7f10 [mpi3mr]
The cause of the WARN is 128 bytes memcpy to the 1 byte size array "__u8
replay_buf[1]" in the struct mpi3mr_bsg_in_reply_buf. The array is intended
to be a flexible length array, so the WARN is a false positive.
To suppress the WARN, remove the constant number '1' from the array
declaration and clarify that it has flexible length. Also, adjust the
memory allocation size to match the change.
Suggested-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240323084155.166835-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Justin Stitt <justinstitt@google.com> says:
This series contains multiple replacements of strncpy throughout the
scsi subsystem.
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces. The details of each replacement will be in their
respective patch.
Link: https://lore.kernel.org/r/20240305-strncpy-drivers-scsi-mpi3mr-mpi3mr_fw-c-v3-0-5b78a13ff984@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only a couple of driver updates this time (lpfc and mpt3sas) plus the
usual assorted minor fixes and updates. The major core update is a
set of patches moving retries out of the drivers and into the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZfWpoCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXRgAP9EJN6k
lA+f8he/ckzfJu000zv55uwKeZhI1ytgNnQUGwEAzv7Yetcqra18spuEnHRvxnW9
+lxUGh6revfrO/sc5Ho=
=ONSb
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Only a couple of driver updates this time (lpfc and mpt3sas) plus the
usual assorted minor fixes and updates. The major core update is a set
of patches moving retries out of the drivers and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (84 commits)
scsi: core: Constify the struct device_type usage
scsi: libfc: replace deprecated strncpy() with memcpy()
scsi: lpfc: Replace deprecated strncpy() with strscpy()
scsi: bfa: Fix function pointer type mismatch for state machines
scsi: bfa: Fix function pointer type mismatch for hcb_qe->cbfn
scsi: bfa: Remove additional unnecessary struct declarations
scsi: csiostor: Avoid function pointer casts
scsi: qla1280: Remove redundant assignment to variable 'mr'
scsi: core: Make scsi_bus_type const
scsi: core: Really include kunit tests with SCSI_LIB_KUNIT_TEST
scsi: target: tcm_loop: Make tcm_loop_lld_bus const
scsi: scsi_debug: Make pseudo_lld_bus const
scsi: iscsi: Make iscsi_flashnode_bus const
scsi: fcoe: Make fcoe_bus_type const
scsi: lpfc: Copyright updates for 14.4.0.0 patches
scsi: lpfc: Update lpfc version to 14.4.0.0
scsi: lpfc: Change lpfc_vport load_flag member into a bitmask
scsi: lpfc: Change lpfc_vport fc_flag member into a bitmask
scsi: lpfc: Protect vport fc_nodes list with an explicit spin lock
scsi: lpfc: Change nlp state statistic counters into atomic_t
...
Doubling the number of PHYs also doubled the stack usage of this function,
exceeding the 32-bit limit of 1024 bytes:
drivers/scsi/mpi3mr/mpi3mr_transport.c: In function 'mpi3mr_refresh_sas_ports':
drivers/scsi/mpi3mr/mpi3mr_transport.c:1818:1: error: the frame size of 1636 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Since the sas_io_unit_pg0 structure is already allocated dynamically, use
the same method here. The size of the allocation can be smaller based on
the actual number of phys now, so use this as an upper bound.
Fixes: cb5b608946 ("scsi: mpi3mr: Increase maximum number of PHYs to 64 from 32")
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240123130754.2011469-1-arnd@kernel.org
Tested-by: John Garry <john.g.garry@oracle.com> #build only
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To ensure that the same ID is not obtained during concurrent execution of
the probe, an ida is used to manage the mrioc's ID.
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231229040331.52518-1-kanie@linux.alibaba.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use correct format for function return values.
Delete blank lines that are reported as "bad line:".
mpi3mr_fw.c:482: warning: No description found for return value of 'mpi3mr_get_reply_desc'
mpi3mr_fw.c:1066: warning: bad line:
mpi3mr_fw.c:1109: warning: bad line:
mpi3mr_fw.c:1249: warning: No description found for return value of 'mpi3mr_revalidate_factsdata'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20231221053113.32191-1-rdunlap@infradead.org
Cc: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: <mpi3mr-linuxdrv.pdl@broadcom.com>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly introduced error messages get multiple format strings wrong:
size_t must be printed using the %z modifier rather than %l and dma_addr_t
must be printed by reference using the special %pad pointer type:
drivers/scsi/mpi3mr/mpi3mr_app.c: In function 'mpi3mr_build_nvme_prp':
include/linux/kern_levels.h:5:25: error: format '%llx' expects argument of type 'long long unsigned int', but argument 4 has type 'dma_addr_t' {aka 'unsigned int'} [-Werror=format=]
drivers/scsi/mpi3mr/mpi3mr_app.c:949:25: note: in expansion of macro 'dprint_bsg_err'
949 | dprint_bsg_err(mrioc,
| ^~~~~~~~~~~~~~
include/linux/kern_levels.h:5:25: error: format '%ld' expects argument of type 'long int', but argument 4 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
drivers/scsi/mpi3mr/mpi3mr_app.c:1112:41: note: in expansion of macro 'dprint_bsg_err'
1112 | dprint_bsg_err(mrioc,
| ^~~~~~~~~~~~~~
Fixes: 9536af615d ("scsi: mpi3mr: Support for preallocation of SGL BSG data buffers part-3")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231207142813.935717-1-arnd@kernel.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver acquires the required NVMe SGLs from the pre-allocated
pool.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231205191630.12201-4-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver acquires the required SGLs from the pre-allocated pool.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231205191630.12201-3-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver now supports SGLs for BSG data transfer. Upon loading, the
driver pre-allocates SGLs in chunks of 8k, results in a total of 256 * 8k,
equal to 2MB. These pre-allocated SGLs are reserved for handling BSG
commands and are deallocated during driver unload.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231205191630.12201-2-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current dev handle for the status reply is 0xFFFF, which is invalid.
So fetch the correct value.
Co-developed-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231126053134.10133-5-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a controller reset is underway or the controller is in an unrecoverable
state, the PEL enable management command will be returned as EAGAIN or
EFAULT.
Cc: <stable@vger.kernel.org> # v6.1+
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231126053134.10133-4-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a controller reset, if the firmware changes the state of devices to
"hide", then remove those devices from the OS.
Cc: <stable@vger.kernel.org> # v6.6+
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231126053134.10133-3-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS5116 controllers supports maximum 48 physical PHYs. Modify driver to
accommodate up to 64 PHYs (though current need is to support 48 PHYs).
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20231123160132.4155-4-sumit.saxena@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SCSI EH host reset is the final callback in the escalation chain; once we
reach this we need to reset the controller. As such it defeats the purpose
to skip controller reset if no I/Os are pending and the RAID device is to
be reset; especially after kexec there might be stale commands pending in
firmware for which we have no reference whatsoever. So this patch splits
off the check for pending I/O into a 'bus_reset' function, and leaves the
actual controller reset to the host reset.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231002154328.43718-19-hare@suse.de
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark all of the devices that are exposed to the OS prior to a controller
reset and not detected by the controller after the reset as removed devices
and the I/Os to those devices are unblocked (and returned with
DID_NO_CONNECT) prior to removing the devices one after the other.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230804104248.118924-6-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhance the driver to get the maximum data length per I/O request from IOC
Facts data and report that to the upper layers. If the IOC facts data is
not reported then a default I/O size of 1MB is reported to the OS.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230804104248.118924-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a timestamp update or an event acknowledgment command times out, the
driver invokes the soft reset handler to recover the controller while
holding a mutex lock. The soft reset handler also tries to acquire the same
mutex to send initialization commands to the controller which leads to a
deadlock scenario.
To resolve the issue the driver will check thestatus and if this indicates
the controller is operational, the driver will issue a diagnostic fault
reset and exit out of the command processing function. If the controller is
already faulted or asynchronously reset, then the driver will just exit the
command processing function.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230804104248.118924-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Copy the sense data to internal driver buffer when the firmware completes
any SCSI I/O command sent through admin queue with sense data for further
use.
Fixes: 506bc1a0d6 ("scsi: mpi3mr: Add support for MPT commands")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20230531184025.3803-1-sumit.saxena@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (megaraid_sas, scsi_debug, lpfc, target,
mpi3mr, hisi_sas, arcmsr). The major core change is the
constification of the host templates (which touches everything) along
with other minor fixups and clean ups.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZEmJACYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishU4FAP0WYhFC
rkbY203/+ErUuwvOKum0VwJKUowCaUD0MBwScAD+Ok/NWobmjdXUBbPUbvVkr+hE
8B/xs9hodX+1fVJcVG0=
=fS/j
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (megaraid_sas, scsi_debug, lpfc, target,
mpi3mr, hisi_sas, arcmsr).
The major core change is the constification of the host templates
(which touches everything) along with other minor fixups and clean
ups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (207 commits)
scsi: ufs: mcq: Use pointer arithmetic in ufshcd_send_command()
scsi: ufs: mcq: Annotate ufshcd_inc_sq_tail() appropriately
scsi: cxlflash: s/semahpore/semaphore/
scsi: lpfc: Silence an incorrect device output
scsi: mpi3mr: Use IRQ save variants of spinlock to protect chain frame allocation
scsi: scsi_debug: Fix missing error code in scsi_debug_init()
scsi: hisi_sas: Work around build failure in suspend function
scsi: lpfc: Fix ioremap issues in lpfc_sli4_pci_mem_setup()
scsi: mpt3sas: Fix an issue when driver is being removed
scsi: mpt3sas: Remove HBA BIOS version in the kernel log
scsi: target: core: Fix invalid memory access
scsi: scsi_debug: Drop sdebug_queue
scsi: scsi_debug: Only allow sdebug_max_queue be modified when no shosts
scsi: scsi_debug: Use scsi_host_busy() in delay_store() and ndelay_store()
scsi: scsi_debug: Use blk_mq_tagset_busy_iter() in stop_all_queued()
scsi: scsi_debug: Use blk_mq_tagset_busy_iter() in sdebug_blk_mq_poll()
scsi: scsi_debug: Dynamically allocate sdebug_queued_cmd
scsi: scsi_debug: Use scsi_block_requests() to block queues
scsi: scsi_debug: Protect block_unblock_all_queues() with mutex
scsi: scsi_debug: Change shost list lock to a mutex
...
Driver uses spin lock without irqsave when it needs to acquire a chain
frame. This is done to protect chain frame allocation from multiple
submission threads. If there is any I/O queued from an interrupt context,
and if that requires a chain frame, and if the chain lock is held by the CPU
which got interrupted, then there will be a possible deadlock.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230406101819.10109-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is exiting from the fault watchdog thread if it sees the 0xF002
(Soft reset in progress) fault code.
If the driver initiates the soft reset, then the driver restarts the
watchdog at the end of the soft reset completion. However, if the soft
reset is initiated by the firmware asynchronously, then the driver will
never restart the watchdog and never re-initialize the controller after the
asynchronous soft reset completion.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230331122317.11391-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche <bvanassche@acm.org> says:
It helps humans and the compiler if it is made explicit that SCSI host
templates are not modified. Hence this patch series that constifies most
SCSI host templates. Please consider this patch series for the next merge
window.
Link: https://lore.kernel.org/r/20230322195515.1267197-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver version to 8.4.1.0.0.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-9-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyright year from 2022 to 2023.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-8-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SCSI error handling has taken place for timed out I/Os on a drive and the
corresponding drive is removed. Stop escalating to higher level of reset by
returning the TUR with "I_T NEXUS LOSS OCCURRED" sense key.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify Message Unit Reset timeout value to 120 seconds from the previous
value of 30 seconds.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekant Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a soft reset, while setting up admin queue pairs, the driver
initially sets admin request base and admin reply base addresses to
NULL. This leads to DMA memory pointed by these pointers getting leaked.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Upon Virtual disk removal, firmware sends device status change event
(Virtual disk remove event) and expects the driver to start device remove
handshake (by sending target reset and IOU control command to firmware).
However, the driver does not initiate the device remove handshake which
leads to the firmware fault.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230316110209.60145-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a missing resource clean up in .remove.
Fixes: e22bae3066 ("scsi: mpi3mr: Add expander devices to STL")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230302234336.25456-7-thenzl@redhat.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't allocate memory again when IOC is being reinitialized.
Fixes: fe6db61515 ("scsi: mpi3mr: Handle offline FW activation in graceful manner")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230302234336.25456-6-thenzl@redhat.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A fix for:
DMA-API: pci 0000:83:00.0: device driver has pending DMA allocations while released from device [count=1]
Fixes: 32d457d5a2 ("scsi: mpi3mr: Add framework to issue config requests")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230302234336.25456-3-thenzl@redhat.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the SAS Transport Layer support is enabled and a device exposed to
the OS by the driver fails INQUIRY commands, the driver frees up the memory
allocated for an internal HBA port data structure. However, in some places,
the reference to the freed memory is not cleared. When the firmware sends
the Device Info change event for the same device again, the freed memory is
accessed and that leads to memory corruption and OS crash.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-7-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A wrong variable is checked while populating PRP entries in the PRP page
and this results in failure. No PRP entries in the PRP page were
successfully created and any NVMe Encapsulated commands with PRP of size
greater than 8K failed.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-6-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return proper non-zero return values for all the cases when the controller
initialization and re-initialization fails.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a controller reset operation is triggered to recover the controller from
a fault state, then wait for the snapdump to be saved in the firmware
region before proceeding to reset the controller.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent driver from trying to dereference a NULL pointer in a debug print
while removing a device during driver unload.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of Task Management handling, the driver will disable and enable the
MSIx index zero which belongs to the Admin reply queue. During this
transition the driver loses some interrupts and this leads to Admin request
and ioctl timeouts.
After enabling the interrupts, poll the Admin reply queue to avoid
timeouts.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates that missed the first pull, mostly because of needing more
soak time. Driver updates (zfcp, ufs, mpi3mr, plus two ipr bug
fixes), an enclosure services (ses) update (mostly bug fixes) and
other minor bug fixes and changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZAJf2SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWYeAP9u6umX
5Trq6mtfdPyhSxIhgD6AwJDgVkeApSKAHZRu0AD/dfMTQmeaJory4LD4JW+uAgVl
yFPVz9VPlKTiaM2lwUI=
=BKzr
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Updates that missed the first pull, mostly because of needing more
soak time.
Driver updates (zfcp, ufs, mpi3mr, plus two ipr bug fixes), an
enclosure services (ses) update (mostly bug fixes) and other minor bug
fixes and changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: zfcp: Trace when request remove fails after qdio send fails
scsi: zfcp: Change the type of all fsf request id fields and variables to u64
scsi: zfcp: Make the type for accessing request hashtable buckets size_t
scsi: ufs: core: Simplify ufshcd_execute_start_stop()
scsi: ufs: core: Rely on the block layer for setting RQF_PM
scsi: core: Extend struct scsi_exec_args
scsi: lpfc: Fix double word in comments
scsi: core: Remove the /proc/scsi/${proc_name} directory earlier
scsi: core: Fix a source code comment
scsi: cxgbi: Remove unneeded version.h include
scsi: qedi: Remove unneeded version.h include
scsi: mpi3mr: Remove unneeded version.h include
scsi: mpi3mr: Fix missing mrioc->evtack_cmds initialization
scsi: mpi3mr: Use number of bits to manage bitmap sizes
scsi: mpi3mr: Remove unnecessary memcpy() to alltgt_info->dmi
scsi: mpi3mr: Fix issues in mpi3mr_get_all_tgt_info()
scsi: mpi3mr: Fix an issue found by KASAN
scsi: mpi3mr: Replace 1-element array with flex-array
scsi: ipr: Work around fortify-string warning
scsi: ipr: Make ipr_probe_ioa_part2() return void
...
Commit c1af985d27 ("scsi: mpi3mr: Add Event acknowledgment logic")
introduced an array mrioc->evtack_cmds but initialization of the array
elements was missed. They are just zero cleared. The function
mpi3mr_complete_evt_ack() refers host_tag field of the elements. Due to the
zero value of the host_tag field, the function calls clear_bit() for
mrico->evtack_cmds_bitmap with wrong bit index. This results in memory
access to invalid address and "BUG: KASAN: use-after-free". This BUG was
observed at eHBA-9600 firmware update to version 8.3.1.0. To fix it, add
the missing initialization of mrioc->evtack_cmds.
Link: https://lore.kernel.org/r/20230214005019.1897251-5-shinichiro.kawasaki@wdc.com
Cc: stable@vger.kernel.org
Fixes: c1af985d27 ("scsi: mpi3mr: Add Event acknowledgment logic")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To allocate bitmaps, the mpi3mr driver calculates sizes of bitmaps using
byte as unit. However, bitmap helper functions assume that bitmaps are
allocated using unsigned long as unit. This gap causes memory access beyond
the bitmap sizes and results in "BUG: KASAN: slab-out-of-bounds". The BUG
was observed at firmware download to eHBA-9600. Call trace indicated that
the out-of-bounds access happened in find_first_zero_bit() called from
mpi3mr_send_event_ack() for miroc->evtack_cmds_bitmap.
To fix the BUG, do not use bytes to manage bitmap sizes. Instead, use
number of bits, and call bitmap helper functions which take number of bits
as arguments. For memory allocation, call bitmap_zalloc() instead of
kzalloc() and krealloc(). For memory free, call bitmap_free() instead of
kfree(). For zero clear, call bitmap_clear() instead of memset().
Remove three fields for bitmap byte sizes in struct scmd_priv which are no
longer required. Replace the field dev_handle_bitmap_sz with
dev_handle_bitmap_bits to keep number of bits of removepend_bitmap across
resize.
Link: https://lore.kernel.org/r/20230214005019.1897251-4-shinichiro.kawasaki@wdc.com
Fixes: c5758fc72b ("scsi: mpi3mr: Gracefully handle online FW update operation")
Fixes: e844adb1fb ("scsi: mpi3mr: Implement SCSI error handler hooks")
Fixes: c1af985d27 ("scsi: mpi3mr: Add Event acknowledgment logic")
Fixes: 824a156633 ("scsi: mpi3mr: Base driver code")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the function mpi3mr_get_all_tgt_info(), devmap_info points to
alltgt_info->dmi then there is no need to memcpy() data from devmap_info to
alltgt_info->dmi. Remove the unnecessary memcpy(). This also allows to
remove the local variable 'rval' and the goto label 'out'.
Link: https://lore.kernel.org/r/20230214005019.1897251-3-shinichiro.kawasaki@wdc.com
Cc: stable@vger.kernel.org
Fixes: f5e6d5a343 ("scsi: mpi3mr: Add support for driver commands")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function mpi3mr_get_all_tgt_info() has four issues:
1) It calculates valid entry length in alltgt_info assuming the header part
of the struct mpi3mr_device_map_info would equal to sizeof(u32). The
correct size is sizeof(u64).
2) When it calculates the valid entry length kern_entrylen, it excludes one
entry by subtracting 1 from num_devices.
3) It copies num_device by calling memcpy(). Substitution is enough.
4) It does not specify the calculated length to sg_copy_from_buffer().
Instead, it specifies the payload length which is larger than the
alltgt_info size. It causes "BUG: KASAN: slab-out-of-bounds".
Fix the issues by using the correct header size, removing the subtraction
from num_devices, replacing the memcpy() with substitution and specifying
the correct length to sg_copy_from_buffer().
Link: https://lore.kernel.org/r/20230214005019.1897251-2-shinichiro.kawasaki@wdc.com
Cc: stable@vger.kernel.org
Fixes: f5e6d5a343 ("scsi: mpi3mr: Add support for driver commands")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When Kconfig item CONFIG_SCSI_MPI3MR was introduced for mpi3mr driver, the
Makefile of the driver was not modified to refer the Kconfig item.
As a result, mpi3mr.ko is built regardless of the Kconfig item value y or
m. Also, if 'make localmodconfig' can not find the Kconfig item in the
Makefile, then it does not generate CONFIG_SCSI_MPI3MR=m even when
mpi3mr.ko is loaded on the system.
Refer to the Kconfig item to avoid the issues.
Fixes: c4f7ac6461 ("scsi: mpi3mr: Add mpi30 Rev-R headers and Kconfig")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20221207023659.2411785-1-shinichiro.kawasaki@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the usage of dma_get_required_mask() API. Directly set the DMA mask
to 63/64 if the system is a 64bit machine.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20221111102246.19995-2-sreekanth.reddy@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After it receives command reply, mpi3mr driver checks command result. If
the result is not zero, it prints out command information. This debug
information is confusing since they are printed even when the non-zero
result is expected. "Power-on or device reset occurred" is printed for Test
Unit Ready command at drive detection. Inquiry failure for unsupported VPD
page header is also printed. They are harmless but look like failures.
To avoid the confusion, print the command reply debug information only when
the module parameter logging_level has value MPI3_DEBUG_SCSI_ERROR= 64, in
same manner as mpt3sas driver.
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20221111014449.1649968-1-shinichiro.kawasaki@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target); the biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so. Beyond the usual bug fixing and
security class reworks, there aren't a huge number of core changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY0B74yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishW2NAP9CPp2R
7NRmSyxcyVYvtCNUW3WxXh65Gn+KgArmg8XucgEAhUBX1fSjOzpERWEU+UaXitbE
Rb+FbjxSc5YxR+nJ/Qc=
=0Wlp
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target). The biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so.
Beyond the usual bug fixing and security class reworks, there aren't a
huge number of core changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
scsi: mpi3mr: Remove unnecessary cast
scsi: stex: Properly zero out the passthrough command structure
scsi: mpi3mr: Update driver version to 8.2.0.3.0
scsi: mpi3mr: Fix scheduling while atomic type bug
scsi: mpi3mr: Scan the devices during resume time
scsi: mpi3mr: Free enclosure objects during driver unload
scsi: mpi3mr: Handle 0xF003 Fault Code
scsi: mpi3mr: Graceful handling of surprise removal of PCIe HBA
scsi: mpi3mr: Schedule IRQ kthreads only on non-RT kernels
scsi: mpi3mr: Support new power management framework
scsi: mpi3mr: Update mpi3 header files
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix ioc->base_readl() use"
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix writel() use"
scsi: wd33c93: Remove dead code related to the long-gone config WD33C93_PIO
scsi: core: Add I/O timeout count for SCSI device
scsi: qedf: Populate sysfs attributes for vport
scsi: pm8001: Replace one-element array with flexible-array member
scsi: 3w-xxxx: Replace one-element array with flexible-array member
scsi: hptiop: Replace one-element array with flexible-array member in struct hpt_iop_request_ioctl_command()
...
coccinelle reports a warning:
WARNING: casting value returned by memory allocation function to (struct
mpi3mr_throttle_group_info *) is useless
To fix this, the unnecessary cast is removed.
Link: https://lore.kernel.org/r/Yx+kp8NxHvDHs7dv@playground
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix 'scheduling while atomic' type bug, which is observed when
pci_irq_vector() is called from interrupt context.
Link: https://lore.kernel.org/r/20220912135742.11764-9-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scan the target devices during system resume time and add or remove the
target device with the SML if the corresponding target device is newly
added or removed respectively.
Link: https://lore.kernel.org/r/20220912135742.11764-8-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Free the enclosure device objects during driver unload and before
rescanning the target devices during controller reset.
Link: https://lore.kernel.org/r/20220912135742.11764-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handle the 0xF003 controller fault code as a special case by marking the
controller as unrecoverable with logging a message indicating the driver
marks the controller as unrecoverable due to the specific fault.
Link: https://lore.kernel.org/r/20220912135742.11764-6-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement graceful handling of surprise or orderly removal of PCIe HBA:
- Detect a hot removal of the controller at certain critical places in the
driver. Early detection will help to reduce the time taken for cleaning
up the hot-removed controller at the driver level.
- Poll the status of the port enable issued after reset once every 5
seconds to avoid a long delay in detecting unavailable controller.
Link: https://lore.kernel.org/r/20220912135742.11764-5-sreekanth.reddy@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In RT kernels, the IRQ handler's code is executed as a kernel
thread. Modify the driver to avoid explicitly scheduling the IRQ kernel
thread.
Link: https://lore.kernel.org/r/20220912135742.11764-4-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch to the new generic PCI power management framework. Also, remove
unnecessary calls to the PCI helper functions (such as
pci_set_power_state(), pci_enable_wake(), pci_save_state(),
pci_restore_state() etc).
Link: https://lore.kernel.org/r/20220912135742.11764-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error code from mpi3mr_post_transport_req() is supposed to be passed to
bsg_job_done(job, rc, reslen), but it isn't.
Link: https://lore.kernel.org/r/YyMISJzVDARpVwrr@kili
Fixes: 176d4aa69c ("scsi: mpi3mr: Support SAS transport class callbacks")
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are three error paths which return success:
1) Propagate the error code from mpi3mr_post_transport_req() if it fails.
2) Return -EINVAL if "ioc_status != MPI3_IOCSTATUS_SUCCESS".
3) Return -EINVAL if "le16_to_cpu(mpi_reply.response_data_length) !=
sizeof(struct rep_manu_reply)"
Link: https://lore.kernel.org/r/YyMIJh1HU2Qz9+Rs@kili
Fixes: 2bd37e2849 ("scsi: mpi3mr: Add framework to issue MPT transport cmds")
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Block the I/Os on the target devices until corresponding target device's
target dev objects are refreshed as part of post controller reset
operation.
Link: https://lore.kernel.org/r/20220804131226.16653-16-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the host's SAS ports if there is change in port id or phys. If the
port id is changed, then the driver updates it. If some phys are
enabled/disabled during reset, then driver updates them in STL.
Check for the responding expander devices and update the device handle if
it got changed. Register the expander with STL if it got added during reset
and unregister the expander device if it got removed during reset.
[mkp: include fix for zeroday warning]
Link: https://lore.kernel.org/r/20220804131226.16653-15-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for the following SAS transport class callbacks:
- get_linkerrors
- get_enclosure_identifier
- get_bay_identifier
- phy_reset
- phy_enable
- set_phy_speed
- smp_handler
Link: https://lore.kernel.org/r/20220804131226.16653-14-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add framework to issue MPT transport commands to controllers. Also issue
the MPT transport commands to get the manufacturing info of SAS expander
device.
Link: https://lore.kernel.org/r/20220804131226.16653-13-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register/unregister the SAS, SATA devices to SCSI Transport Layer(STL)
whenever the corresponding device is added/removed from topology.
Link: https://lore.kernel.org/r/20220804131226.16653-12-sreekanth.reddy@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When device is registered with the STL then get the corresponding device's
target object using the rphy in below callback functions:
- mpi3mr_target_alloc()
- mpi3mr_slave_alloc()
- mpi3mr_slave_configure()
- mpi3mr_slave_destroy()
Link: https://lore.kernel.org/r/20220804131226.16653-11-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register/unregister the expander devices to SCSI Transport Layer(STL)
whenever the corresponding expander is added/removed from topology.
Link: https://lore.kernel.org/r/20220804131226.16653-10-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register the SAS, SATA devices to SCSI Transport Layer (STL) only if
multipath capability is disabled in the controller's firmware.
Link: https://lore.kernel.org/r/20220804131226.16653-9-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the following helper functions:
- Update the host phys with STL
- Remove the device's SAS port with STL
Link: https://lore.kernel.org/r/20220804131226.16653-8-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the following helper functions:
- Get the device's sas address by reading corresponding device's Device
page0
- Get the expander object from expander list based on expander's handle
- Get the target device object from target device list based on device's
sas address
- Get the expander device object from expander list based on expanders's
sas address
- Get hba port object from hba port table list based on port's port id
Link: https://lore.kernel.org/r/20220804131226.16653-7-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add framework to register and unregister the host and expander phys with
SCSI Transport Layer (STL).
Link: https://lore.kernel.org/r/20220804131226.16653-6-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable and process the Enclosure device add event.
Link: https://lore.kernel.org/r/20220804131226.16653-5-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
