Missed service event tells the driver that the hardware wasn't able to
process some queued isoc TDs in their right time slots, and some TDs will
be skipped. The driver sets a 'skip' flag to indicate that the next
transfer event after this event will point to some future TD instead of
the next queued TD. Once the driver receives the next event, it will skip
and give back all those hardware skipped TDs.
However, should this subsequent event be a stop endpoint which does not
point to the next pending TD, the driver fails to return the skipped TDs.
Instead, it loops for a period before outputting an erroneous message.
Fix this by repositioning the 'stop endpoint' check to follow the isoc
skip check, ensuring the skipped TDs are properly returned.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When xhci_requires_manual_halt_cleanup() was written it wasn't clear
that the xhci internal endpoint halt state always needs to be cleared
with a reset endpoint command. Functional stall cases additionally halt
the device side endpoint which requires class driver to clear the device
side halt with a CLEAR_FEATURE(ENDPOINT_HALT) request as well.
Clean up, rename, and make sure the new function always return true
when internal endpoint state is halted, including stall cases.
Based on related cleanup suggestion code by Niklas Neronin
cc: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove debug messages that served as sanity checks during the initial
implementation phase of underrun/overrun completion codes. These checks
are now unnecessary.
Instead, improve the default debug messages for underrun/overrun events,
so that they are consistent with the reset of the completion codes.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve error message for unknown transfer event without a TRB, by also
printing the event code number. This removes the inevitable question;
"what was the unknown event code exactly?"
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move handling transfer events without a target transfer TRB into
handle_transferless_tx_event(), this type of event does not utilize the
rest of handle_tx_event() and as a result it's better to separate it
into a dedicated function.
Additionally, this change reduces handle_tx_event()'s size and makes it
more readable.
[Mathias: Simplify code to return helper function value directly. This
removes the second xhci_err() message for untargeted and unexpected
event completion types]
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a preparation patch for switching from custom segment list
handling to using list.h functions.
Contain all segment re-numbering in xhci_link_rings() which links two
segments lists together, and performs all necessary adjustments for
them to fit together.
No need to send segment number to xhci_alloc_segments_for_ring()
as a parameter after this.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older 0.95 xHCI hosts and some other specific newer hosts require the
chain bit to be set for Link TRBs even if the link TRB is not in the
middle of a transfer descriptor (TD).
move the checks for all those cases into one xhci_link_chain_quirk()
function to clean up and avoid code duplication.
No functional changes.
[skip renaming chain_links flag, reword commit message -Mathias]
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Argument struct 'xhci_interrupter *ir' is not used, and as a consequence
is removed.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Argument u32 'cmd_comp_code' is not used, and as a consequence
is removed.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove argument 'struct xhci_hcd *xhci' from functions which do not
utilize it. This change contributes to a simpler codebase by avoiding
redundant arguments.
Functions which have the argument removed:
check_interval()
xhci_num_trbs_free()
xhci_handle_cmd_enable_slot()
xhci_clear_interrupt_pending()
xhci_requires_manual_halt_cleanup()
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove 'num_trbs' from 'xhci_td' as it's no longer used following the
removal of 'num_trbs_free' tracking in commit 2710f8186f ("xhci: Stop
unnecessary tracking of free trbs in a ring").
Tracking of 'num_trbs_free' is still performed in xhci DbC, but it does not
utilize 'num_trbs'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci DbC driver polls the host controller for DbC events at a reduced
rate when DbC is enabled but there are no active data transfers.
Allow users to modify this reduced poll interval via dbc_poll_interval_ms
sysfs entry. Unit is milliseconds and accepted range is 0 to 5000.
Max interval of 5000 ms is selected as it matches the common 5 second
timeout used in usb stack.
Default value is 64 milliseconds.
A long interval is useful when users know there won't be any activity
on systems connected via DbC for long periods, and want to avoid
battery drainage due to unnecessary CPU usage.
Example being Android Debugger (ADB) usage over DbC on ChromeOS systems
running Android Runtime.
[minor changes and rewording -Mathias]
Co-developed-by: Samuel Jacob <samjaco@google.com>
Signed-off-by: Samuel Jacob <samjaco@google.com>
Signed-off-by: Uday M Bhat <uday.m.bhat@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transferred length is incorrectly zeroed for cancelled isoc
transfer TDs when the transfer ring stops on a cancelled TD with
a 'Stop - Length Invalid' completion code.
Length was always set to zero in these cases even if it should be
set to the sum of the TRB transfer block lengths up to
the TRB the ring stopped on, _excluding_ the one stopped on.
No issues reported due to this isoc case. Found while inspecting
related case in bulk transfer 'Stop - Length Invalid' handling.
Change this so that 'Stop - Length Invalid' transfer completion
cases always sum up TRB lengths instead of report a zero length.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parsing xhci traces on systems with several xHCI controllers and connected
usb devices is difficult as entries are all interleaved.
showing usb devname in urb tracing reveals both which device, and which
bus/controller the entry is for.
old:
xhci_urb_enqueue: ep2in-bulk: urb 0000000039224498 ...
new:
xhci_urb_enqueue: 3-9.4 ep1in-bulk: urb 0000000013bf21e7 ...
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This codepath is trivially dead, since the function is never called with
a non-NULL td (the only callsite is immediately preceded by a NULL guard).
[remove unused label 'deq_found' -Mathias]
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI specification 5.1 "Register Conventions" states that 64 bit
registers should be written in low-high order. All writing operations
in xhci is done low-high order following the spec.
Add a new quirk to support workaround for high-low order.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-4-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This quirk is for the controller that has a limitation in supporting
separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. That's because
the internal initialization of event ring fetches the
"Event Ring Segment Table Entry" based on the indication of ERSTBA_LO
written.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-3-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/host/ohci-exynos.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/host/xhci-pci-renesas.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240611-md-drivers-usb-host-v1-1-e2071a696ef8@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmZvTbAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGVksIAJEn4a9IVM8FNCJy
Dxo0BItD1/qJ5mLDptqUFRKlxInjbojofz5CyoeIeXb0DwRfB16ALXqNXAkd3APi
saoOpfjFsg2H2OqL9CHdkzWcJEAq2lDnL0zaOjumeDVu/EyeT+tC4e4hq1e6Bm0E
fPC5ms2b+07DF9Rg6/DW8yPbdM5n6Mz1bRd3fQOIgvpM3yGOyGztEBgTRub/ZUgH
5pNJauknFAZgdiWhgNpc+lPWYZbgHKULQPhUBPdVhDIXPtQNUlKgNTQc6+L0Nmbb
K1sG1q7FLeMJOTFGQfD4r26X5DNQUi894q/9SX8X7rcrECdJKcw2WjVyB4myADpf
ae2gP+A=
=XjWP
-----END PGP SIGNATURE-----
Merge tag 'v6.10-rc4' into usb-next
We need the USB / Thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple streams are in use, multiple TDs might be in flight when
an endpoint is stopped. We need to issue a Set TR Dequeue Pointer for
each, to ensure everything is reset properly and the caches cleared.
Change the logic so that any N>1 TDs found active for different streams
are deferred until after the first one is processed, calling
xhci_invalidate_cancelled_tds() again from xhci_handle_cmd_set_deq() to
queue another command until we are done with all of them. Also change
the error/"should never happen" paths to ensure we at least clear any
affected TDs, even if we can't issue a command to clear the hardware
cache, and complain loudly with an xhci_warn() if this ever happens.
This problem case dates back to commit e9df17eb14 ("USB: xhci: Correct
assumptions about number of rings per endpoint.") early on in the XHCI
driver's life, when stream support was first added.
It was then identified but not fixed nor made into a warning in commit
674f8438c1 ("xhci: split handling halted endpoints into two steps"),
which added a FIXME comment for the problem case (without materially
changing the behavior as far as I can tell, though the new logic made
the problem more obvious).
Then later, in commit 94f339147f ("xhci: Fix failure to give back some
cached cancelled URBs."), it was acknowledged again.
[Mathias: commit 94f339147f ("xhci: Fix failure to give back some cached
cancelled URBs.") was a targeted regression fix to the previously mentioned
patch. Users reported issues with usb stuck after unmounting/disconnecting
UAS devices. This rolled back the TD clearing of multiple streams to its
original state.]
Apparently the commit author was aware of the problem (yet still chose
to submit it): It was still mentioned as a FIXME, an xhci_dbg() was
added to log the problem condition, and the remaining issue was mentioned
in the commit description. The choice of making the log type xhci_dbg()
for what is, at this point, a completely unhandled and known broken
condition is puzzling and unfortunate, as it guarantees that no actual
users would see the log in production, thereby making it nigh
undebuggable (indeed, even if you turn on DEBUG, the message doesn't
really hint at there being a problem at all).
It took me *months* of random xHC crashes to finally find a reliable
repro and be able to do a deep dive debug session, which could all have
been avoided had this unhandled, broken condition been actually reported
with a warning, as it should have been as a bug intentionally left in
unfixed (never mind that it shouldn't have been left in at all).
> Another fix to solve clearing the caches of all stream rings with
> cancelled TDs is needed, but not as urgent.
3 years after that statement and 14 years after the original bug was
introduced, I think it's finally time to fix it. And maybe next time
let's not leave bugs unfixed (that are actually worse than the original
bug), and let's actually get people to review kernel commits please.
Fixes xHC crashes and IOMMU faults with UAS devices when handling
errors/faults. Easiest repro is to use `hdparm` to mark an early sector
(e.g. 1024) on a disk as bad, then `cat /dev/sdX > /dev/null` in a loop.
At least in the case of JMicron controllers, the read errors end up
having to cancel two TDs (for two queued requests to different streams)
and the one that didn't get cleared properly ends up faulting the xHC
entirely when it tries to access DMA pages that have since been unmapped,
referred to by the stale TDs. This normally happens quickly (after two
or three loops). After this fix, I left the `cat` in a loop running
overnight and experienced no xHC failures, with all read errors
recovered properly. Repro'd and tested on an Apple M1 Mac Mini
(dwc3 host).
On systems without an IOMMU, this bug would instead silently corrupt
freed memory, making this a security bug (even on systems with IOMMUs
this could silently corrupt memory belonging to other USB devices on the
same controller, so it's still a security bug). Given that the kernel
autoprobes partition tables, I'm pretty sure a malicious USB device
pretending to be a UAS device and reporting an error with the right
timing could deliberately trigger a UAF and write to freed memory, with
no user action.
[Mathias: Commit message and code comment edit, original at:]
https://lore.kernel.org/linux-usb/20240524-xhci-streams-v1-1-6b1f13819bea@marcan.st/
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Fixes: 94f339147f ("xhci: Fix failure to give back some cached cancelled URBs.")
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in commit 8f873c1ff4 ("xhci: Blacklist using streams on the
Etron EJ168 controller"), EJ188 have the same issue as EJ168, where Streams
do not work reliable on EJ188. So apply XHCI_BROKEN_STREAMS quirk to EJ188
as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in commit c877b3b2ad ("xhci: Add reset on resume quirk for
asrock p67 host"), EJ188 have the same issue as EJ168, where completely
dies on resume. So apply XHCI_RESET_ON_RESUME quirk to EJ188 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transferred length is set incorrectly for cancelled bulk
transfer TDs in case the bulk transfer ring stops on the last transfer
block with a 'Stop - Length Invalid' completion code.
length essentially ends up being set to the requested length:
urb->actual_length = urb->transfer_buffer_length
Length for 'Stop - Length Invalid' cases should be the sum of all
TRB transfer block lengths up to the one the ring stopped on,
_excluding_ the one stopped on.
Fix this by always summing up TRB lengths for 'Stop - Length Invalid'
bulk cases.
This issue was discovered by Alan Stern while debugging
https://bugzilla.kernel.org/show_bug.cgi?id=218890, but does not
solve that bug. Issue is older than 4.10 kernel but fix won't apply
to those due to major reworks in that area.
Tested-by: Pierre Tomon <pierretom+12@ik.me>
Cc: stable@vger.kernel.org # v4.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ehci_dbg_port' is unused in oxu210hp-hcd.c since it's original
commit b92a78e582 ("usb host: Oxford OXU210HP HCD driver.")
when it was in a separate header.
Remove it.
Note, that this structure, and some others in the driver
are mostly clones of include/linux/usb/ehci_def.h.
Someone with the hardware to be able to test it might
be able to remove a lot more structs as well and just
use that header.
Signed-off-by: "Dr. David Alan Gilbert" <linux@treblig.org>
Link: https://lore.kernel.org/r/20240529210002.106369-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmY39LkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGaB8H+wWcwT1O7K2SQx1a
sHDYJSXfbjgShS7Wt+gbDNvhGJqG/5FkpHyBmBKUdElZs8QMf21GAbIfJvzcNThA
g+FakIMjfhNH/dr6TJXHWbb2NZV67exDbbuaQDyMhNhIZqil4BH/OEPbLYIdquvm
/HDGFB/whVoHVC+Ug8esEOL3Uy+rizBDlsT/K4ZgpOC3TuUmlRpptSVACwjcCGXM
PFKyyTIr0ZnKcz3+4yTEtpDFm6e/ujxMwM66GBCgmPaZ3lJp5ruY3kGpBTmSyoqV
Rh3CQlIhBo8gwlAx/yQXfxEZomhxT6DfRpc6s/1W0J1UZN/j2pYy056OYyckG32c
uQ9ujxQ=
=M0wP
-----END PGP SIGNATURE-----
Merge 6.9-rc7 into usb-next
We want the USB fixes in here as well, and resolve a merge conflict in
drivers/usb/dwc3/core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary repeated calls to TRB_TO_SLOT_ID(). The slot ID is
stored in the 'slot_id' variable at the function's start.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's better to keep track on Thunderbolt xHCI IDs in a separate group.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three out of many Intel platforms that are using TLAs
instead of the full names in the PCI IDs. Modify them accordingly.
This also fixes the logic of grouping as seemed to be by an LSB
byte of the ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By removing the goto 'cleanup' statement, and replacing it with 'continue',
'break' and 'return', helps simplify the code and further showcase in which
case the while loop iterates.
This change prepares for the comprehensive handle_tx_event() rework.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplifying the handle_tx_event() function by addressing the complexity
of its while loop. Replaces specific 'goto cleanup' statements with
'return' statements, applicable only where 'ep->skip' is set to 'false',
ensuring loop termination.
The original while loop, combined with 'goto cleanup', adds unnecessary
complexity. This change aims to untangle the loop's logic, facilitating a
more straightforward review of the upcoming comprehensive rework.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handle_tx_event() encounters a COMP_MISSED_SERVICE_ERROR or
COMP_NO_PING_RESPONSE_ERROR event, it moves to 'goto cleanup'.
Here, it sets a flag, 'handling_skipped_tds', based on conditions that
exclude these two error events.
Subsequently, the process evaluates the loop that persists as long as
'handling_skipped_tds' remains true. However, since 'trb_comp_code' does
not change after its assignment, if it indicates either of the two error
conditions, the loop terminates immediately.
To simplify this process and enhance clarity, the modification involves
returning immediately upon detecting COMP_MISSED_SERVICE_ERROR or
COMP_NO_PING_RESPONSE_ERROR. This adjustment allows for the direct use of
'ep->skip', removing the necessity for the 'handling_skipped_tds' flag.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some transfer events don't always point to a TRB, and consequently don't
have a endpoint ring. In these cases, function handle_tx_event() should
not proceed, because if 'ep->skip' is set, the pointer to the endpoint
ring is used.
To prevent a potential failure and make the code logical, return after
checking the completion code for a Transfer event without TRBs.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this quirk was set then driver would treat transfer events with
'Success' completion code as 'Short packet' if there were untransferred
bytes left.
This is so common that turn it into default behavior.
xhci_warn_ratelimited() is no longer used after this, so remove it.
A success event with untransferred bytes left doesn't always mean a
misbehaving controller. If there was an error mid a multi-TRB TD it's
allowed to issue a success event for the last TRB in that TD.
See xhci 1.2 spec 4.9.1 Transfer Descriptors
"Note: If an error is detected while processing a multi-TRB TD, the xHC
shall generate a Transfer Event for the TRB that the error was detected
on with the appropriate error Condition Code, then may advance to the
next TD. If in the process of advancing to the next TD, a Transfer TRB
is encountered with its IOC flag set, then the Condition Code of the
Transfer Event generated for that Transfer TRB should be Success,
because there was no error actually associated with the TRB that
generated the Event. However, an xHC implementation may redundantly
assert the original error Condition Code."
Co-developed-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print the full hex value of PORTSC register in addition to the human
readable decoded string while debugging PORTSC value.
If PORTSC value is 0xffffffff then don't decode it.
This lets us inspect Rsvd bits of PORTSC.
Same is done for USBSTS register values.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace size_mul() with array_size() in memory allocation and freeing
processes, it fits better semantically.
Macro array_size() is identical to size_mult(), which clamps the max size,
so it's imperative that array_size() is used when freeing said memory.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'erst_size' represents the maximum capacity of entries that ERST can hold,
while 'num_entries' indicates the actual number of entries currently held
in the ERST. These two values are identical because the xhci driver does
not support ERST expansion. Thus, 'erst_size' is removed.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the number of do-while loops by 1. The number of loops should be
number of segment + 1, the +1 is in case deq and enq are on the same
segment. But due to the use of a do-while loop, the expression is
evaluated after executing the loop, thus the loop is executed 1 extra
time.
Changing the do-while loop expression from "<=" to "<", reduces the loop
amount by 1. The expression "<=" would also work if it was a while loop
instead of a do-while loop.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Address debug message inaccuracies in xhci_ring_expansion_needed().
Specifically, remove the portion of the debug message that indicates the
number of enqueue TRBs to be added to the dequeue segment. This part of
the message may mislead and the calculated value is incorrect. Given that
this value is not of significant importance and the statement is not
consistently accurate, it has been omitted.
The specific issues with the debug message that this commit resolves:
- The calculation of the number of TRBs is incorrect. The current
calculation erroneously includes the link TRB, which is reserved.
Furthermore, the calculated number of TRBs can exceed the dequeue
segment, resulting in a misleading debug message.
- The current phrasing suggests that "ring expansion by X is needed,
adding X TRBs moves enqueue Y TRBs into the dequeue segment".
The intended message, however, is "IF the ring is NOT expanded by X,
THEN adding X TRBs moves enqueue Y TRBs into the dequeue segment".
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c412 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helper was only called from one function.
Removing it both reduces lines of code and made it more readable.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port capability flags for USB2 ports have been cached in an
u32 xhci->ext_caps[] array long before the driver had struct xhci_port
and struct xhci_port_cap structures.
Move these cached USB2 port capability values together with the other
port capability values into struct xhci_port_cap cability structure.
This also gets rid of the cumbersome way of mapping port to USB2
capability based on portnum as each port has a pointer to its capability
structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing ohci functionality with qemu's pci-ohci emulation often results
in ohci interface stalls, resulting in hung task timeouts.
The problem is caused by lost interrupts between the emulation and the
Linux kernel code. Additional interrupts raised while the ohci interrupt
handler in Linux is running and before the handler clears the interrupt
status are not handled. The fix for a similar problem in ehci suggests
that the problem is likely caused by edge-triggered MSI interrupts. See
commit 0b60557230 ("usb: ehci: Prevent missed ehci interrupts with
edge-triggered MSI") for details.
Ensure that the ohci interrupt code handles all pending interrupts before
returning to solve the problem.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: stable@vger.kernel.org
Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://lore.kernel.org/r/20240429154010.1507366-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This macro has the advantage over SIMPLE_DEV_PM_OPS that we don't have to
care about when the functions are actually used.
Also make use of pm_ptr() to discard all PM related stuff if CONFIG_PM
isn't enabled.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-5-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-4-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This macro has the advantage over SIMPLE_DEV_PM_OPS that we don't have to
care about when the functions are actually used.
Also make use of pm_ptr() to discard all PM related stuff if CONFIG_PM
isn't enabled.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-3-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240412142317.5191-2-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer from a xhci usb virt device to its root hub port
(vdev->rhub_port) is set later when device is addressed, not while
vdev is allocated.
Tracepoints dereferenced this rhub_port pointer when freeing the virt
device, which causes null pointer dereference if tracing is enabled
and device is freed before addressed.
This can happen if tracing is enabled and xhci driver is unloaded before
a device is fully enumerated, or initial enumeration fails and device
is reset and freed before retry.
Don't dereference the rhub_port or show port numbers when tracing
xhci_free_virt_device(). This info is not very useful anyway.
Print the more useful slot id instead
Fixes: 06790c1908 ("xhci: replace real & fake port with pointer to root hub port")
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Closes: https://lore.kernel.org/linux-usb/20240402005007.klv2ij727fkz7rpd@synopsys.com/
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240404121106.2842417-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get STS_HCE we give up on the interrupt, but for the purpose
of IRQ handling that still counts as ours. We may return IRQ_NONE
only if we are positive that it wasn't ours. Hence correct the default.
Fixes: 2a25e66d67 ("xhci: print warning when HCE was set")
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240404121106.2842417-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macros with good names offer better readability. Besides, also move
the definition to ehci.h.
Signed-off-by: Dingyan Li <18500469033@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240309033709.14604-1-18500469033@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots of
tiny changes and forward progress to support new hardware and better
support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZfwpzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymS9QCdEuF6KJFLOrDrGS4NbZNSUPIVF6oAn350r4NX
CMZah37Dfr1VDCOOV4gQ
=HACL
-----END PGP SIGNATURE-----
Merge tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots
of tiny changes and forward progress to support new hardware and
better support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues"
* tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (185 commits)
usb: usb-acpi: Fix oops due to freeing uninitialized pld pointer
usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
phy: tegra: xusb: Add API to retrieve the port number of phy
USB: gadget: pxa27x_udc: Remove unused of_gpio.h
usb: gadget/snps_udc_plat: Remove unused of_gpio.h
usb: ohci-pxa27x: Remove unused of_gpio.h
usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
usb: Clarify expected behavior of dev_bin_attrs_are_visible()
xhci: Allow RPM on the USB controller (1022:43f7) by default
usb: isp1760: remove SLAB_MEM_SPREAD flag usage
usb: misc: onboard_hub: use pointer consistently in the probe function
usb: gadget: fsl: Increase size of name buffer for endpoints
usb: gadget: fsl: Add of device table to enable module autoloading
usb: typec: tcpm: add support to set tcpc connector orientatition
usb: typec: tcpci: add generic tcpci fallback compatible
dt-bindings: usb: typec-tcpci: add tcpci fallback binding
usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}
usb: core: Set connect_type of ports based on DT node
dt-bindings: usb: Add downstream facing ports to realtek binding
...
Function checkdone is only required if QUIRK2 is defined, so add
appropriate #if / #endif around the function.
Cleans up clang scan build warning:
drivers/usb/host/sl811-hcd.c:588:18: warning: unused function
'checkdone' [-Wunused-function]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240307111351.1982382-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ring expansion checker may incorrectly assume a completely full ring
is empty, missing the need for expansion.
This is due to a special empty ring case where the dequeue ends up
ahead of the enqueue pointer. This is seen when enqueued TRBs fill up
exactly a segment, with enqueue then pointing to the end link TRB.
Once those TRBs are handled the dequeue pointer will follow the link
TRB and end up pointing to the first entry on the next segment, past
the enqueue.
This same enqueue - dequeue condition can be true if a ring is full,
with enqueue ending on that last link TRB before the dequeue pointer
on the next segment.
This can be seen when queuing several ~510 small URBs via usbfs in
one go before a single one is handled (i.e. dequeue not moved from first
entry in segment).
Expand the ring already when enqueue reaches the link TRB before the
dequeue segment, instead of expanding it when enqueue moves into the
dequeue segment.
Reported-by: Chris Yokum <linux-usb@mail.totalphase.com>
Closes: https://lore.kernel.org/all/949223224.833962.1709339266739.JavaMail.zimbra@totalphase.com
Tested-by: Chris Yokum <linux-usb@mail.totalphase.com>
Fixes: f5af638f06 ("xhci: Fix transfer ring expansion size calculation")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240305132312.955171-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci_map_urb_for_dma() creates a temporary buffer and copies
the SG list to the new linear buffer. But if the kzalloc_node() fails,
then the following sg_pcopy_to_buffer() can lead to crash since it
tries to memcpy to NULL pointer.
So return -ENOMEM if kzalloc returns null pointer.
Cc: stable@vger.kernel.org # 5.11
Fixes: 2017a1e584 ("usb: xhci: Use temporary buffer to consolidate SG")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DbC driver starts polling for events immediately when DbC is enabled.
The current polling interval is 1ms, which keeps the CPU busy, impacting
power management even when there are no active data transfers.
Solve this by polling at a slower rate, with a 64ms interval as default
until a transfer request is queued, or if there are still are pending
unhandled transfers at event completion.
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two NEC uPD720200 adapters have been observed to randomly misbehave:
a Stop Endpoint command fails with Context Error, the Output Context
indicates Stopped state, and the endpoint keeps running. Very often,
Set TR Dequeue Pointer is seen to fail next with Context Error too,
in addition to problems from unexpectedly completed cancelled work.
The pathology is common on fast running isoc endpoints like uvcvideo,
but has also been reproduced on a full-speed bulk endpoint of pl2303.
It seems all EPs are affected, with risk proportional to their load.
Reproduction involves receiving any kind of stream and closing it to
make the device driver cancel URBs already queued in advance.
Deal with it by retrying the command like in the Running state.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A trb_in_td() call is used to determine if a completion event matches
any TRB of the currently executing TD. This function is told to start
searching right after the last finished TD, which is not at all where
the currently expected TD is guaranteed to begin, because some TDs in
between may have been cancelled.
Not only is a pointless work performed, but a bug resulting in the HC
executing cancelled TDs was seen to trick the driver into associating
events from a TD just cancelled with an unrelated future TD.
Since the ring is being traversed for the specific purpose of finding
a match with the current TD, always start from its first TRB. This is
the most reliable bit of information that we posses.
Tracking of HC's work progress is not affected, except for cases when
a misattributed event would have moved dequeue past a pending TD.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the code to improve readability by using
'xhci_free_segments_for_ring()' function for freeing ring segments.
This replaces the custom while loop previously used within
'xhci_ring_expansion()' and 'xhci_alloc_segments_for_ring()'.
Slightly modify 'xhci_free_segments_for_ring()' to handle lists
which do not loop. This makes it possible to use it in error
paths of 'xhci_alloc_segments_for_ring()'.
This change also prepares for switching the custom xhci linked segment
list into to more standard list.h lists.
[minor commit message rewording -Mathias]
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace a segment of code within 'xhci_clear_command_ring()' with a
function call to 'xhci_initialize_ring_info()'. This change eliminates
code duplication, as 'xhci_initialize_ring_info()' performs the same
operations as the replaced code.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Slot ID is a index of a virtual device in struct 'xhci_hcd->devs[]'.
Previously, to get the slot ID associated with a port, we had to loop
through all devices and compare ports, which is very inefficient.
Instead, the slot ID (of the device which is directly connected to the
port), is added to the its corresponding 'xhci_port' struct. As a result,
finding the port's device is quick and easy.
Function 'xhci_find_slot_id_by_port()' is removed, as it is no longer
needed.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables real & fake port do not convey their purpose, thus they are
replaced with a pointer to the root hub port 'struct xhci_port *rhub_port'.
'rhub_port' contains real & fake ports in zero-based format, which happens
to be more widely used inside the xHCI driver:
- 'real_port' is ('rhub_port->hw_portnum' + 1)
- 'fake_port' is ('rhub_port->hcd_portnum' + 1)
One reason for real port being one-based, is to signal other functions in
case struct 'xhci_virt_device' initialization failed, in this case the
value will remain 0. This is no longer needed, instead we check whether
or not 'rhub_port' is 'NULL'.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hardware needs to know which roothub port a USB device is attached to
when controlling the device, so the xHCI driver stores in each device the
roothub port which it's connected behind. This is done with two different
port index values, the 'real_port' which is an index to the xHC hardware
port register array, and the 'fake_port' which is the per hub port index
used by the hub driver.
Instead of finding real & fake port separately, find the root hub port
'xhci_port' structure which contains both real & fake port values:
- 'real_port' is ('hw_portnum' + 1)
- 'fake_port' is ('hcd_portnum' + 1)
i.e. real & fake port are 'hw_portnum' & 'hcd_portnum' in one-based
format.
The 'xhci_port' structure is a better way to refer to roothub ports than
the 'real_port' & 'fake_port'. As a result, these port indexes are slated
to be replaced with a direct pointer to the root hub port. This patch
setups the ground work for the future changes.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need it here for the USB fixes, and it resolves a merge conflict as
reported in linux-next in drivers/usb/roles/class.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes relying upon linux/of_platform.h to include
linux/platform_device.h, which it no longer does, thereby fixing
compilation problems like:
In file included from drivers/usb/host/uhci-hcd.c:850:
drivers/usb/host/uhci-grlib.c: In function 'uhci_hcd_grlib_probe':
drivers/usb/host/uhci-grlib.c:92:29: error: invalid use of undefined type 'struct platform_device'
92 | struct device_node *dn = op->dev.of_node;
| ^~
Fixes: ef175b29a2 ("of: Stop circularly including of_device.h and of_platform.h")
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20240129075056.1511630-1-andreas@gaisler.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose xhci_stop_endpoint_sync() which is a synchronous variant of
xhci_queue_stop_endpoint(). This is useful for client drivers that are
using the secondary interrupters, and need to stop/clean up the current
session. The stop endpoint command handler will also take care of cleaning
up the ring.
Modifications to repurpose the new API into existing stop endpoint
sequences was implemented by Wesley Cheng.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-11-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some sequences, will require traversing through the entire event ring
without handling the event TRB. This is ideal for when secondary
interrupters that are utilized by external entities need to clean up the
interrupter's event rings during halting of the XHCI HCD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-10-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if the event ring exists and is valid once when the event handler
is called, not before every individual event TRB.
At this point the interrupter is valid, so no need to check that.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-9-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add unhandled_event_trb() that returns true in case xHC hardware has
written new event trbs to the event ring that driver has not yet handled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-8-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the main XHCI interrupt handler into a different API, so that other
potential interrupters can utilize similar event ring handling. A scenario
would be if a secondary interrupter required to skip pending events in the
event ring, which would warrant a similar set of operations.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-7-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event ring dequeue pointer field (ERDP) in xHC hardware is used to
inform controller how far the driver has processed events on the event
ring.
In the case all events are handled and event ring is empty then the
address of the TRB after the last processed one should be written.
This TRB is both the enqueue and dequeue pointer.
But in case we are writing the ERDP in the middle of processing
several events then ERDP field should be written with the "up to and
including" address of the last handled event TRB.
Currenly each ERDP write by driver is done as if all events are handled
and ring is empty.
Fix this by adjusting the order when software dequeue "inc_deq()"
is called and hardware dequeue "xhci_update_erst_dequeue()" is updated.
Details in xhci 1.2 specification section 4.9.4:
"System software shall write the Event Ring Dequeue Pointer (ERDP)
register to inform the xHC that it has completed the processing of Event
TRBs up to and including the Event TRB referenced by the ERDP.
The detection of a Cycle bit mismatch in an Event TRB processed by
software indicates the location of the xHC Event Ring Enqueue Pointer
and that the Event Ring is empty. Software shall write the ERDP with
the address of this TRB to indicate that it has processed all Events
in the ring"
This change depends on fixes made to relocate inc_deq() calls captured
in the below commits:
commit 3321f84bfa ("xhci: simplify event ring dequeue tracking for
transfer events")
commit d1830364e9 ("xhci: Simplify event ring dequeue pointer update
for port change events")
Fixes: dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event_ring_deq parameter is used to check if the event ring dequeue
position is updated while calling by xhci_handle_event(), meaning there was
an actual event on the ring to handle. In this case the driver needs to
inform hardware about the updated dequeue position.
Basically event_ring_deq just stores the old event ring dequeue position
before calling the event handler.
Keeping track of software event dequeue updates this way is no longer
useful as driver anyways reads the current hardware dequeue position
within the handle event, and checks if it needs to be updated.
The driver might anyway need to modify the EHB (event handler busy) bit in
the same register as the dequeue pointer even if the actual dequeue
position did not change.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isoc_bei_interval is used to balance how often completed isochronous
events cause interrupts. If interval is too large then the event ring
may fill up before the completed isoc TRBs are handled.
isoc_bei_interval is tuned based on how full the event ring is.
isoc_bei_interval variable needs to be per interrupter as
with several interrupters each one has its own event ring.
move isoc_bei_interval variable to the interrupter structure.
if a secondary interrupter does not care about this feature then
keep isoc_bei_interval 0.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to set the interrupt moderation interval for an interrupter.
Each interrupter can have its own moderation value.
Hardware has a 16bit register for the moderation value, each step is 250ns.
Helper function imod_interval argument is in nanoseconds.
Values from 0 to 16383750 (250 x 0xffff) are accepted.
0 means no interrupt throttling.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each interrupter has an interrupt pending (IP) bit that should be cleared
in the interrupt handler. This is done automatically for systems using
MSI/MSI-X interrupts.
Secondary interrupters used by audio offload may not actually trigger
MSI/MSI-X messages, so driver may need to clear the IP bit manually for
these, even if the primary interrupter IP is cleared automatically.
Add an ip_autoclear flag to each interrupter that driver can configure
when requesting an interrupt for that xHC interrupter, and move
the interrupt pending clearing code to its own helper function.
Use this ip_autoclear flag instead of the current hcd->msi_enabled
to check if IP flag is cleared by software.
[Moved ip_autoclear into xhci and set based on msi_enabled -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the PORT and CAPs macro definitions into a separate file to
facilitate sharing with other files without the need to include the entire
xhci.h.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for ac5 to the EHCI Orion platform driver.
The ac5 SOC has DDR starting at offset 0x2_0000_0000,
Hence it requires a larger than 32-bit DMA mask to operate.
Move the dma mask to be pointed by the OF match data, and
use that match data when initializng the DMA mask.
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240114172154.2622275-3-enachman@marvell.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sanity check of interrupter index when adding a new interrupter is
off by one. intr_num needs to be smaller than xhci->max_interrupter to
fit the array of interrupters.
Luckily this doesn't cause any real word harm as xhci_add_interrupter()
is always called with a intr_num value smaller than xhci->max_interrupters
in any current kernel.
Should not be needed for stable as 6.7 kernel and older only supports
one interrupter, with intr_num always being zero.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-usb/e9771296-586d-456a-ac24-a82de79bb2e6@moroto.mountain/
Fixes: 4bf398e15a ("xhci: split allocate interrupter into separate alloacte and add parts")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit bac1ec5514 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11
Fixes: bac1ec5514 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
many places. The notable patch series are:
- nilfs2 folio conversion from Matthew Wilcox in "nilfs2: Folio
conversions for file paths".
- Additional nilfs2 folio conversion from Ryusuke Konishi in "nilfs2:
Folio conversions for directory paths".
- IA64 remnant removal in Heiko Carstens's "Remove unused code after
IA-64 removal".
- Arnd Bergmann has enabled the -Wmissing-prototypes warning everywhere
in "Treewide: enable -Wmissing-prototypes". This had some followup
fixes:
- Nathan Chancellor has cleaned up the hexagon build in the series
"hexagon: Fix up instances of -Wmissing-prototypes".
- Nathan also addressed some s390 warnings in "s390: A couple of
fixes for -Wmissing-prototypes".
- Arnd Bergmann addresses the same warnings for MIPS in his series
"mips: address -Wmissing-prototypes warnings".
- Baoquan He has made kexec_file operate in a top-down-fitting manner
similar to kexec_load in the series "kexec_file: Load kernel at top of
system RAM if required"
- Baoquan He has also added the self-explanatory "kexec_file: print out
debugging message if required".
- Some checkstack maintenance work from Tiezhu Yang in the series
"Modify some code about checkstack".
- Douglas Anderson has disentangled the watchdog code's logging when
multiple reports are occurring simultaneously. The series is "watchdog:
Better handling of concurrent lockups".
- Yuntao Wang has contributed some maintenance work on the crash code in
"crash: Some cleanups and fixes".
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZZ2R6AAKCRDdBJ7gKXxA
juCVAP4t76qUISDOSKugB/Dn5E4Nt9wvPY9PcufnmD+xoPsgkQD+JVl4+jd9+gAV
vl6wkJDiJO5JZ3FVtBtC3DFA/xHtVgk=
=kQw+
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2024-01-09-10-33' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Quite a lot of kexec work this time around. Many singleton patches in
many places. The notable patch series are:
- nilfs2 folio conversion from Matthew Wilcox in 'nilfs2: Folio
conversions for file paths'.
- Additional nilfs2 folio conversion from Ryusuke Konishi in 'nilfs2:
Folio conversions for directory paths'.
- IA64 remnant removal in Heiko Carstens's 'Remove unused code after
IA-64 removal'.
- Arnd Bergmann has enabled the -Wmissing-prototypes warning
everywhere in 'Treewide: enable -Wmissing-prototypes'. This had
some followup fixes:
- Nathan Chancellor has cleaned up the hexagon build in the series
'hexagon: Fix up instances of -Wmissing-prototypes'.
- Nathan also addressed some s390 warnings in 's390: A couple of
fixes for -Wmissing-prototypes'.
- Arnd Bergmann addresses the same warnings for MIPS in his series
'mips: address -Wmissing-prototypes warnings'.
- Baoquan He has made kexec_file operate in a top-down-fitting manner
similar to kexec_load in the series 'kexec_file: Load kernel at top
of system RAM if required'
- Baoquan He has also added the self-explanatory 'kexec_file: print
out debugging message if required'.
- Some checkstack maintenance work from Tiezhu Yang in the series
'Modify some code about checkstack'.
- Douglas Anderson has disentangled the watchdog code's logging when
multiple reports are occurring simultaneously. The series is
'watchdog: Better handling of concurrent lockups'.
- Yuntao Wang has contributed some maintenance work on the crash code
in 'crash: Some cleanups and fixes'"
* tag 'mm-nonmm-stable-2024-01-09-10-33' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (157 commits)
crash_core: fix and simplify the logic of crash_exclude_mem_range()
x86/crash: use SZ_1M macro instead of hardcoded value
x86/crash: remove the unused image parameter from prepare_elf_headers()
kdump: remove redundant DEFAULT_CRASH_KERNEL_LOW_SIZE
scripts/decode_stacktrace.sh: strip unexpected CR from lines
watchdog: if panicking and we dumped everything, don't re-enable dumping
watchdog/hardlockup: use printk_cpu_sync_get_irqsave() to serialize reporting
watchdog/softlockup: use printk_cpu_sync_get_irqsave() to serialize reporting
watchdog/hardlockup: adopt softlockup logic avoiding double-dumps
kexec_core: fix the assignment to kimage->control_page
x86/kexec: fix incorrect end address passed to kernel_ident_mapping_init()
lib/trace_readwrite.c:: replace asm-generic/io with linux/io
nilfs2: cpfile: fix some kernel-doc warnings
stacktrace: fix kernel-doc typo
scripts/checkstack.pl: fix no space expression between sp and offset
x86/kexec: fix incorrect argument passed to kexec_dprintk()
x86/kexec: use pr_err() instead of kexec_dprintk() when an error occurs
nilfs2: add missing set_freezable() for freezable kthread
kernel: relay: remove relay_file_splice_read dead code, doesn't work
docs: submit-checklist: remove all of "make namespacecheck"
...
Modify the XHCI drivers to accommodate for handling multiple event rings in
case there are multiple interrupters. Add the required APIs so clients are
able to allocate/request for an interrupter ring, and pass this information
back to the client driver. This allows for users to handle the resource
accordingly, such as passing the event ring base address to an audio DSP.
There is no actual support for multiple MSI/MSI-X vectors.
[export xhci_initialize_ring_info() -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240102214549.22498-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Gen1 isoc-in transfer, host still send out unexpected ACK after device
finish the burst with a short packet, this will cause an exception on the
connected device, such as, a usb 4k camera.
It can be fixed by setting rxfifo depth less than 4k bytes, prefer to use
3k here, the side-effect is that may cause performance drop about 10%,
including bulk transfer.
Fixes: 926d60ae64 ("usb: xhci-mtk: modify the SOF/ITP interval for mt8195")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci retaining bogus hardware states cause usb disconnect devices
connected before hibernation(s4) and refer to the commit 'f3d478858be
("usb: ohci-platform: fix usb disconnect issue after s4")' which set
flag "hibernated" as true when resume-from-hibernation and that the
drivers will reset the hardware to get rid of any existing state and
make sure resume from hibernation re-enumerates everything for xhci.
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20231228071113.1719-1-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During device enumeration usb core resets endpoint 0 if the max packet
size value differs from the one read from the device descriptor.
usb core will additionally reset endpoint 0 during S4 resume, before
re-enumerating the device, if the device has a reset-resume flag set.
In this case the xhci device representation vdev may be lost due to
xHC restore error and re-initialization during S4 resume.
Make sure slot_id and vdev are valid before trying to re-configure max
packet size during endpoint 0 reset.
max packet size will be re-configured later during re-enumeration.
This fixes commit e34900f46c ("xhci: Reconfigure endpoint 0 max packet
size only during endpoint reset") which is currently in usb-next,
on its way to 6.8
Fixes: e34900f46c ("xhci: Reconfigure endpoint 0 max packet size only during endpoint reset")
Tested-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231215125707.1732989-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Cristian Birsan <cristian.birsan@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-8-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is only called locally and should always have been static:
drivers/usb/host/fsl-mph-dr-of.c:291:5: error: no previous prototype for 'fsl_usb2_mpc5121_init' [-Werror=missing-prototypes]
Link: https://lkml.kernel.org/r/20231123110506.707903-6-arnd@kernel.org
Fixes: 230f7ede6c ("USB: add USB EHCI support for MPC5121 SoC")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Tudor Ambarus <tudor.ambarus@linaro.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
With the introduction of a BCM2711 specific compatible, this also
needs to be added to the xHCI driver.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231205200531.8232-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4baf121815.
Enabling runtime pm as default for all AMD xHC 1.1 controllers caused
regression. An initial attempt to fix those was done in commit a5d6264b63
("xhci: Enable RPM on controllers that support low-power states") but new
issues are still seen.
Revert this to get those AMD xHC 1.1 systems working
This patch went to stable an needs to be reverted from there as well.
Fixes: 4baf121815 ("xhci: Loosen RPM as default policy to cover for AMD xHC 1.1")
Link: https://lore.kernel.org/linux-usb/55c50bf5-bffb-454e-906e-4408c591cb63@molgen.mpg.de
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231205090548.1377667-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a short gap between urb being submitted and actually added to the
endpoint queue (linked). If the device is disconnected during this time
then usb core is not yet aware of the pending urb, and device may be freed
just before xhci_urq_enqueue() continues, dereferencing the freed device.
Freeing the device is protected by the xhci spinlock, so make sure we take
and keep the lock while checking that device exists, dereference it, and
add the urb to the queue.
Remove the unnecessary URB check, usb core checks it before calling
xhci_urb_enqueue()
Suggested-by: Kuen-Han Tsai <khtsai@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
