A number of mlxsw-specific QoS tests use manual QoS DCB management. As
such, they need to make sure lldpad is not running, because it would
override the configuration the test has applied using other tools. To that
end, these selftests invoke the bail_on_lldpad() helper, which terminates
the selftest if th lldpad is running.
Some of these tests however first install the bash exit trap, which invokes
a cleanup() at the test exit. If bail_on_lldpad() has terminated the script
even before the setup part was run, the cleanup part will be very confused.
Therefore make sure bail_on_lldpad() is invoked before the cleanup is
registered.
While there are still edge cases where the user terminates the script
before the setup was fully done, this takes care of a common situation
where the cleanup would be invoked in an inconsistent state.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test basic (port-default, VLAN PCP and IP DSCP) QoS classification for
Ocelot switches. Advanced QoS classification using tc filters is covered
by tc_flower_chains.sh in the same directory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220502155424.4098917-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a test that sends 1Gbps of traffic through the switch, into which it
then injects a burst of traffic and tests that there are no drops.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Felix VSC9959 switch in NXP LS1028A supports the tc-gate action
which enforced time-based access control per stream. A stream as seen by
this switch is identified by {MAC DA, VID}.
We use the standard forwarding selftest topology with 2 host interfaces
and 2 switch interfaces. The host ports must require timestamping non-IP
packets and supporting tc-etf offload, for isochron to work. The
isochron program monitors network sync status (ptp4l, phc2sys) and
deterministically transmits packets to the switch such that the tc-gate
action either (a) always accepts them based on its schedule, or
(b) always drops them.
I tried to keep as much of the logic that isn't specific to the NXP
LS1028A in a new tsn_lib.sh, for future reuse. This covers
synchronization using ptp4l and phc2sys, and isochron.
The cycle-time chosen for this selftest isn't particularly impressive
(and the focus is the functionality of the switch), but I didn't really
know what to do better, considering that it will mostly be run during
debugging sessions, various kernel bloatware would be enabled, like
lockdep, KASAN, etc, and we certainly can't run any races with those on.
I tried to look through the kselftest framework for other real time
applications and didn't really find any, so I'm not sure how better to
prepare the environment in case we want to go for a lower cycle time.
At the moment, the only thing the selftest is ensuring is that dynamic
frequency scaling is disabled on the CPU that isochron runs on. It would
probably be useful to have a blacklist of kernel config options (checked
through zcat /proc/config.gz) and some cyclictest scripts to run
beforehand, but I saw none of those.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20220501112953.3298973-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once line card is activated, check the device FW version is exposed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once line card is provisioned, check if HW revision and INI version
are exposed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once line card is provisioned, check the count of devices on it and
print them out.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an initial subset of forwarding selftests which I considered
to be relevant for DSA drivers, along with a forwarding.config that
makes it easier to run them (disables veth pair creation, makes sure MAC
addresses are unique and stable).
The intention is to request driver writers to run these selftests during
review and make sure that the tests pass, or at least that the problems
are known.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend tcpdump_start() & C:o to handle multiple instances. Useful when
observing bridge operation, e.g., unicast learning/flooding, and any
case of multicast distribution (to these ports but not that one ...).
This means the interface argument is now a mandatory argument to all
tcpdump_*() functions, hence the changes to the ocelot flower test.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test verifies that packets are correctly flooded by the bridge and
the VXLAN device by matching on the encapsulated packets at the other
end. However, if packets other than those generated by the test also
ingress the bridge (e.g., MLD packets), they will be flooded as well and
interfere with the expected count.
Make the test more robust by making sure that only the packets generated
by the test can ingress the bridge. Drop all the rest using tc filters
on the egress of 'br0' and 'h1'.
In the software data path, the problem can be solved by matching on the
inner destination MAC or dropping unwanted packets at the egress of the
VXLAN device, but this is not currently supported by mlxsw.
Fixes: d01724dd2a ("selftests: mlxsw: spectrum-2: Add a test for VxLAN flooding with IPv6")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test verifies that packets are correctly flooded by the bridge and
the VXLAN device by matching on the encapsulated packets at the other
end. However, if packets other than those generated by the test also
ingress the bridge (e.g., MLD packets), they will be flooded as well and
interfere with the expected count.
Make the test more robust by making sure that only the packets generated
by the test can ingress the bridge. Drop all the rest using tc filters
on the egress of 'br0' and 'h1'.
In the software data path, the problem can be solved by matching on the
inner destination MAC or dropping unwanted packets at the egress of the
VXLAN device, but this is not currently supported by mlxsw.
Fixes: 94d302deae ("selftests: mlxsw: Add a test for VxLAN flooding")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic line card manipulation which consists of provisioning,
unprovisioning and activation of a line card.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights:
- new drivers:
- AMD Host System Management Port (HSMP)
- Intel Software Defined Silicon
- removed drivers (functionality folded into other drivers):
- intel_cht_int33fe_microb
- surface3_button
- amd-pmc:
- s2idle bug-fixes
- Support for AMD Spill to DRAM STB feature
- hp-wmi:
- Fix SW_TABLET_MODE detection method (and other fixes)
- Support omen thermal profile policy v1
- serial-multi-instantiate:
- Add SPI device support
- Add support for CS35L41 amplifiers used in new laptops
- think-lmi:
- syfs-class-firmware-attributes Certificate authentication support
- thinkpad_acpi:
- Fixes + quirks
- Add platform_profile support on AMD based ThinkPads
- x86-android-tablets
- Improve Asus ME176C / TF103C support
- Support Nextbook Ares 8, Lenovo Tab 2 830 and 1050 tablets
- Lots of various other small fixes and hardware-id additions
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for CS35L41
ACPI / x86:
- Add support for LPS0 callback handler
ALSA:
- hda/realtek: Add support for HP Laptops
Add AMD system management interface:
- Add AMD system management interface
Add Intel Software Defined Silicon driver:
- Add Intel Software Defined Silicon driver
Documentation:
- syfs-class-firmware-attributes: Lenovo Certificate support
- Add x86/amd_hsmp driver
ISST:
- Fix possible circular locking dependency detected
Input:
- soc_button_array - add support for Microsoft Surface 3 (MSHW0028) buttons
Merge remote-tracking branch 'pdx86/platform-drivers-x86-pinctrl-pmu_clk' into review-hans-gcc12:
- Merge remote-tracking branch 'pdx86/platform-drivers-x86-pinctrl-pmu_clk' into review-hans-gcc12
Merge tag 'platform-drivers-x86-serial-multi-instantiate-1' into review-hans:
- Merge tag 'platform-drivers-x86-serial-multi-instantiate-1' into review-hans
Replace acpi_bus_get_device():
- Replace acpi_bus_get_device()
amd-pmc:
- Only report STB errors when STB enabled
- Drop CPU QoS workaround
- Output error codes in messages
- Move to later in the suspend process
- Validate entry into the deepest state on resume
- uninitialized variable in amd_pmc_s2d_init()
- Set QOS during suspend on CZN w/ timer wakeup
- Add support for AMD Spill to DRAM STB feature
- Correct usage of SMU version
- Make amd_pmc_stb_debugfs_fops static
asus-tf103c-dock:
- Make 2 global structs static
asus-wmi:
- Fix regression when probing for fan curve control
hp-wmi:
- support omen thermal profile policy v1
- Changing bios_args.data to be dynamically allocated
- Fix 0x05 error code reported by several WMI calls
- Fix SW_TABLET_MODE detection method
- Fix hp_wmi_read_int() reporting error (0x05)
huawei-wmi:
- check the return value of device_create_file()
i2c-multi-instantiate:
- Rename it for a generic serial driver name
int3472:
- Add terminator to gpiod_lookup_table
intel-uncore-freq:
- fix uncore_freq_common_init() error codes
intel_cht_int33fe:
- Move to intel directory
- Drop Lenovo Yogabook YB1-X9x code
- Switch to DMI modalias based loading
intel_crystal_cove_charger:
- Fix IRQ masking / unmasking
lg-laptop:
- Move setting of battery charge limit to common location
pinctrl:
- baytrail: Add pinconf group + function for the pmu_clk
platform/dcdbas:
- move EXPORT_SYMBOL after function
platform/surface:
- Remove Surface 3 Button driver
- surface3-wmi: Simplify resource management
- Replace acpi_bus_get_device()
- Reinstate platform dependency
platform/x86/intel-uncore-freq:
- Split common and enumeration part
platform/x86/intel/uncore-freq:
- Display uncore current frequency
- Use sysfs API to create attributes
- Move to uncore-frequency folder
selftests:
- sdsi: test sysfs setup
serial-multi-instantiate:
- Add SPI support
- Reorganize I2C functions
spi:
- Add API to count spi acpi resources
- Support selection of the index of the ACPI Spi Resource before alloc
- Create helper API to lookup ACPI info for spi device
- Make spi_alloc_device and spi_add_device public again
surface:
- surface3_power: Fix battery readings on batteries without a serial number
think-lmi:
- Certificate authentication support
thinkpad_acpi:
- consistently check fan_get_status return.
- Don't use test_bit on an integer
- Fix compiler warning about uninitialized err variable
- clean up dytc profile convert
- Add PSC mode support
- Add dual fan probe
- Add dual-fan quirk for T15g (2nd gen)
- Fix incorrect use of platform profile on AMD platforms
- Add quirk for ThinkPads without a fan
tools arch x86:
- Add Intel SDSi provisiong tool
touchscreen_dmi:
- Add info for the RWC NANOTE P8 AY07J 2-in-1
x86-android-tablets:
- Depend on EFI and SPI
- Lenovo Yoga Tablet 2 830/1050 sound support
- Workaround Lenovo Yoga Tablet 2 830/1050 poweroff hang
- Add Lenovo Yoga Tablet 2 830 / 1050 data
- Fix EBUSY error when requesting IOAPIC IRQs
- Minor charger / fuel-gauge improvements
- Add Nextbook Ares 8 data
- Add IRQ to Asus ME176C accelerometer info
- Add lid-switch gpio-keys pdev to Asus ME176C + TF103C
- Add x86_android_tablet_get_gpiod() helper
- Add Asus ME176C/TF103C charger and fuelgauge props
- Add battery swnode support
- Trivial typo fix for MODULE_AUTHOR
- Fix the buttons on CZC P10T tablet
- Constify the gpiod_lookup_tables arrays
- Add an init() callback to struct x86_dev_info
- Add support for disabling ACPI _AEI handlers
- Correct crystal_cove_charger module name
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmI8SjEUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9wYUwf/cdUMPFy5cwpHq1LuqGy+PxVCRHCe
71PFd2Ycj+HGOtrt66RxSiCC1Seb4tylr7FvudToDaqWjlBf5n6LhpDudg4ds7Qw
lCuRlaXTIrF7p3nOLIsWvJPRqacMG79KkRM62MLTS2evtRYjbnKvFzNPJPzr8827
1AhCakE92S8gkR5lUZYYHtsaz9rZ4z4TrEtjO6GdlbL2bDw0l18dNNwdMomfVpNS
bBIHIDLeufDuMJ4PxIHlE5MB3AuZAuc0HTJWihozyJX/h5FMGI6qVm0/s9RAfHgX
XdMCpADtS/JjHCmkFgLZYIzvXTxwQVZRo5VO0Wrv5Mis6gSpxJXCd0aKlA==
=1x9/
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"New drivers:
- AMD Host System Management Port (HSMP)
- Intel Software Defined Silicon
Removed drivers (functionality folded into other drivers):
- intel_cht_int33fe_microb
- surface3_button
amd-pmc:
- s2idle bug-fixes
- Support for AMD Spill to DRAM STB feature
hp-wmi:
- Fix SW_TABLET_MODE detection method (and other fixes)
- Support omen thermal profile policy v1
serial-multi-instantiate:
- Add SPI device support
- Add support for CS35L41 amplifiers used in new laptops
think-lmi:
- syfs-class-firmware-attributes Certificate authentication support
thinkpad_acpi:
- Fixes + quirks
- Add platform_profile support on AMD based ThinkPads
x86-android-tablets:
- Improve Asus ME176C / TF103C support
- Support Nextbook Ares 8, Lenovo Tab 2 830 and 1050 tablets
Lots of various other small fixes and hardware-id additions"
* tag 'platform-drivers-x86-v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (60 commits)
platform/x86: think-lmi: Certificate authentication support
Documentation: syfs-class-firmware-attributes: Lenovo Certificate support
platform/x86: amd-pmc: Only report STB errors when STB enabled
platform/x86: amd-pmc: Drop CPU QoS workaround
platform/x86: amd-pmc: Output error codes in messages
platform/x86: amd-pmc: Move to later in the suspend process
ACPI / x86: Add support for LPS0 callback handler
platform/x86: thinkpad_acpi: consistently check fan_get_status return.
platform/x86: hp-wmi: support omen thermal profile policy v1
platform/x86: hp-wmi: Changing bios_args.data to be dynamically allocated
platform/x86: hp-wmi: Fix 0x05 error code reported by several WMI calls
platform/x86: hp-wmi: Fix SW_TABLET_MODE detection method
platform/x86: hp-wmi: Fix hp_wmi_read_int() reporting error (0x05)
platform/x86: amd-pmc: Validate entry into the deepest state on resume
platform/x86: thinkpad_acpi: Don't use test_bit on an integer
platform/x86: thinkpad_acpi: Fix compiler warning about uninitialized err variable
platform/x86: thinkpad_acpi: clean up dytc profile convert
platform/x86: x86-android-tablets: Depend on EFI and SPI
platform/x86: amd-pmc: uninitialized variable in amd_pmc_s2d_init()
platform/x86: intel-uncore-freq: fix uncore_freq_common_init() error codes
...
Add a test that verifies that UAPI notifications are emitted, as mlxsw
installs and deinstalls HW counters for the L3 offload xstats.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a test that verifies basic UAPI contracts, netdevsim operation,
rollbacks after partial enablement in core, and UAPI notifications.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The test runs several test cases and is supposed to return an error in
case at least one of them failed.
Currently, the check of the return value of each test case is in the
wrong place, which can result in the wrong return value. For example:
# TESTS='tc_police' ./resource_scale.sh
TEST: 'tc_police' [default] 968 [FAIL]
tc police offload count failed
Error: mlxsw_spectrum: Failed to allocate policer index.
We have an error talking to the kernel
Command failed /tmp/tmp.i7Oc5HwmXY:969
TEST: 'tc_police' [default] overflow 969 [ OK ]
...
TEST: 'tc_police' [ipv4_max] overflow 969 [ OK ]
$ echo $?
0
Fix this by moving the check to be done after each test case.
Fixes: 059b18e21c ("selftests: mlxsw: Return correct error code in resource scale test")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test adds tc filters and checks how many of them were offloaded by
grepping for 'in_hw'.
iproute2 commit f4cd4f127047 ("tc: add skip_hw and skip_sw to control
action offload") added offload indication to tc actions, producing the
following output:
$ tc filter show dev swp2 ingress
...
filter protocol ipv6 pref 1000 flower chain 0 handle 0x7c0
eth_type ipv6
dst_ip 2001:db8:1::7bf
skip_sw
in_hw in_hw_count 1
action order 1: police 0x7c0 rate 10Mbit burst 100Kb mtu 2Kb action drop overhead 0b
ref 1 bind 1
not_in_hw
used_hw_stats immediate
The current grep expression matches on both 'in_hw' and 'not_in_hw',
resulting in incorrect results.
Fix that by using JSON output instead.
Fixes: 5061e77326 ("selftests: mlxsw: Add scale test for tc-police")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tests file configuration and error handling of the Intel Software
Defined Silicon sysfs ABI.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20220225012457.1661574-2-david.e.box@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Change the case that sends packets with "too short inner packet" to
include part of ethernet header, to make the trap to be triggered due to
the correct reason.
According to ASIC arch, the trap is triggered if overlay packet length is
less than 18B, and the minimum inner packet should include source MAC and
destination MAC.
Till now the case passed because one of the reserved bits in VxLAN
header was used. This issue was found while adding an equivalent test
for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test configures VxLAN with IPv6 underlay and verifies that the
expected traps are triggered under the right conditions.
The test is similar to the existing IPv4 test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.
The number of records is changed according to ASIC type and address
family.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-2 and above, which support up to four
IPv6 addresses in one record.
The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.
The number of records is changed according to ASIC type and address
family.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-1 switches, which support up to five
IPv6 addresses in one record.
The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to verify FDB vetos of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_fdb_veto.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.
Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.
The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to verify configuration of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.
Add separated test cases for learning which is not supported for IPv6
and for UDP checksum flags which are different from IPv4 flags.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.
Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.
The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.
Rename some functions to include "ipv4", so the next patch will add
equivalent functions for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a test case to verify that VxLAN with IPv6 underlay
is forbidden.
Remove this test case as support for VxLAN with IPv6 underlay was added
by the previous patch.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test case to cover the bug fixed by the previous patch.
Edit the MAC address of one netdev so that it matches the MAC address of
the second netdev. Verify that the two MAC profiles were consolidated by
testing that the MAC profiles occupancy decreased by one.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TBF can be used as a root qdisc, with the usual ETS/RED/TBF hierarchy below
it. This use should now be offloaded. Add a test that verifies that it is.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After adding the previous patches, the constraint that all the router
interface MAC addresses have the same prefix is no longer relevant.
Remove the test cases that validated that this constraint is honored.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When all the RIF MAC profiles are in use, test that it is possible to
change the MAC of a netdev (i.e., a RIF) when its MAC profile is not
shared with other RIFs. Test that replacement fails when the MAC profile
is shared.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that MAC profile changes are indeed applied and that packets are
forwarded with the correct source MAC.
Output example:
$ ./rif_mac_profiles.sh
TEST: h1->h2: new mac profile [ OK ]
TEST: h2->h1: new mac profile [ OK ]
TEST: h1->h2: edit mac profile [ OK ]
TEST: h2->h1: edit mac profile [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query the maximum number of supported RIF MAC profiles using
devlink-resource and verify that all available MAC profiles can be utilized
and that an error is generated when user space tries to exceed this number.
Output example in Spectrum-2:
$ TESTS='rif_mac_profile' ./resource_scale.sh
TEST: 'rif_mac_profile' 4 [ OK ]
TEST: 'rif_mac_profile' overflow 5 [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of iterating over all the available trap policers, only perform
the tests with three policers: The first, the last and the one in the
middle of the range. On a Spectrum-3 system, this reduces the run time
from almost an hour to a few minutes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop objects tests configure dummy reachable neighbours so that
the nexthops will have a MAC address and be programmed to the device.
Since these are dummy reachable neighbours, they can be transitioned by
the kernel to a failed state if they are around for too long. This can
happen, for example, if the "TIMEOUT" variable is configured with a too
high value.
Make the tests more robust by configuring the neighbours as permanent,
so that the tests do not depend on the configured timeout value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of mlxsw-specific selftests currently detect whether they are run
on a compatible machine, and bail out silently when not. These tests are
however done in a somewhat impenetrable manner by directly comparing PCI
IDs against a blacklist or a whitelist, and bailing out silently if the
machine is not compatible.
Instead, add a helper, mlxsw_only_on_spectrum(), which allows specifying
the supported machines in a human-readable manner. If the current machine
is incompatible, the helper emits a SKIP message and returns an error code,
based on which the caller can gracefully bail out in a suitable way. This
allows a more readable conditions such as:
mlxsw_only_on_spectrum 2+ || return
Convert all existing open-coded guards to the new helper. Also add two new
guards to do_mark_test() and do_drop_test(), which are supported only on
Spectrum-2+, but the corresponding check was not there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is a bit strange in that it is perhaps more manual than
others: it does not transmit a clear OK/FAIL verdict, because user space
does not have synchronous feedback from the kernel. If a hardware access
fails, it is in deferred context.
Nonetheless, on sja1105 I have used it successfully to find and solve a
concurrency issue, so it can be used as a starting point for other
driver maintainers too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is a bit strange in that it is perhaps more manual than
others: it does not transmit a clear OK/FAIL verdict, because user space
does not have synchronous feedback from the kernel. If a hardware access
fails, it is in deferred context.
Nonetheless, on sja1105 I have used it successfully to find and solve a
concurrency issue, so it can be used as a starting point for other
driver maintainers too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This checks that various qdisc configurations either are or are not
offloaded.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a variant of ECN test that uses qdisc marked counter (supported on
Spectrum-3 and above) instead of the aggregate ethtool ecn_marked counter.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add do_mark_test(), which is to do_ecn_test() like do_drop_test() is to
do_red_test(): meant to test that actions on the RED mark qevent block are
offloaded, and executed on ECN-marked packets.
The test splits install_qdisc() into its constituents, install_root_qdisc()
and install_qdisc_tcX(). This is in order to test that when mirroring is
enabled on one TC, the other TC does not mirror.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These variables are cut'n'pasted from other functions in the file and not
actually used.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of adding same test for GRE tunnel with IPv6 underlay, missing
bytes for key were found.
mausezahn does not fill zeros between two colons, so send them
explicitly. For example, use "00:00:00:E9:" instead of ":E9:"
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of adding same test for GRE tunnel with IPv6 underlay, an
optional improvement was found - call ipip_payload_get from
ecn_payload_get, so do not duplicate the code which creates the payload.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of adding same test for GRE tunnel with IPv6 underlay, wrong
alignments were found, fix them.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 underlay support was added, add test to check that "decap_error" trap
is triggered under the right conditions and that devlink counters increase.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kselftest fixes update for Linux 5.15-rc5 consists of a fix
to implicit declaration warns in drivers/dma-buf test.
-----BEGIN PGP SIGNATURE-----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=t85S
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-fixes-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
"A fix to implicit declaration warns in drivers/dma-buf test"
* tag 'linux-kselftest-fixes-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: drivers/dma-buf: Fix implicit declaration warns
For this test we are exercising the VCAP ES0 block's ability to match on
a packet with a given VLAN ID, and push an ES0 TAG A with a VID derived
from VID_A_VAL plus the classified VLAN.
$eth3.200 is the generator port
$eth0 is the bridged DUT port that receives
$eth1 is the bridged DUT port that forwards and rewrites VID 200 to 300
on egress via VCAP ES0
$eth2 is the port that receives from the DUT port $eth1
Since the egress rewriting happens outside the bridging service, VID 300
does not need to be in the bridge VLAN table of $eth1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be one more VLAN modification selftest added, this time for
egress. Rename the one that exists right now to be more specific.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like when I wrote the selftests I was using a network manager that
brought up the ports automatically. In order to not rely on that, let
the script open them up.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udmabuf has the following implicit declaration warns:
udmabuf.c:30:10: warning: implicit declaration of function 'open';
udmabuf.c:42:8: warning: implicit declaration of function 'fcntl'
These are caused due to not including fcntl.h and including just
linux/fcntl.h. Fix it to include fcntl.h which will bring in the
linux/fcntl.h. In addition, define __EXPORTED_HEADERS__ to bring in
F_ADD_SEALS and F_SEAL_SHRINK defines and fix the following error
that show up when just fcntl.h is included.
udmabuf.c:45:21: error: 'F_ADD_SEALS' undeclared
45 | ret = fcntl(memfd, F_ADD_SEALS, F_SEAL_SHRINK);
| ^~~~~~~~~~~
udmabuf.c:45:34: error: 'F_SEAL_SHRINK' undeclared
45 | ret = fcntl(memfd, F_ADD_SEALS, F_SEAL_SHRINK);
| ^~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest for checking mq children are visible after ethtool -L.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hard drop counter check testcase, to make sure netdevsim driver
properly handles the devlink hard drop counters get/set callbacks.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit referenced below, a check was added to devlink_lib that
asserts the existence of a devlink device referenced by $DEVLINK_DEV.
Unfortunately, several netdevsim tests point DEVLINK_DEV at a device that
does not exist at the time that devlink_lib is sourced. Thus these tests
spuriously fail.
Fix this by introducing an override. By setting DEVLINK_DEV to an empty
string, the user declares their intention to handle DEVLINK_DEV management
on their own.
In all netdevsim tests that use devlink_lib and set DEVLINK_DEV, set
instead an empty DEVLINK_DEV just before sourcing devlink_lib, and set it
to the correct value right afterwards.
Fixes: 557c4d2f78 ("selftests: devlink_lib: add check for devlink device existence")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several tests do not set some ports down as part of their cleanup(),
resulting in IPv6 link-local addresses and associated routes not being
deleted.
These leaks were found using a BPF tool that monitors ASIC resources.
Solve this by setting the ports down at the end of the tests.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To check how many routes are installed in hardware, the test runs "ip
route" and greps for "offload", which includes routes with state
"offload_failed".
Till now, this wrong check was not found because after one failure in
route insertion, the driver moved to "abort" mode, which means that user
cannot try to add more routes.
The previous patch removed the abort mechanism and now failed routes are
counted as offloaded.
Fix this by not considering routes with "offload_failed" flag as
offloaded.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that netdevsim correctly implements devlink ops callbacks
that set node as a parent of devlink leaf or node rate object.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that it is possible to create, delete and set min/max tx
rate of devlink rate node on netdevsim VF.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that netdevsim VFs can set and retrieve shared/max tx
rate through new devlink API.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that all netdevsim VF ports have rate leaf object created
by default.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the two users of this helper have been converted to iproute2 dcb,
it is not necessary anymore. Drop it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test sometimes fails with an error message such as:
TEST: tc sample (w/ flower) rate (egress) [FAIL]
Expected 100 packets, got 70 packets, which is -30% off. Required accuracy is +-25%
Make the test more robust by generating more packets, therefore
increasing the number of expected samples. Decrease the transmission
delay in order not to needlessly prolong the test.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the array of the ports that were split in the port_scale test
is local, so the port_cleanup() unsplits an empty array.
Make the array global so the cleanup will be preformed properly.
Suggested-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mirror_gre_scale test creates as many ERSPAN sessions as the underlying
chip supports, and tests that they all work. In order to determine that it
issues a stream of ICMP packets and checks if they are mirrored as
expected.
However, the mausezahn invocation missed the -6 flag to identify the use of
IPv6 protocol, and was sending ICMP messages over IPv6, as opposed to
ICMP6. It also didn't pass an explicit source IP address, which apparently
worked at some point in the past, but does not anymore.
To fix these issues, extend the function mirror_test() in mirror_lib by
detecting the IPv6 protocol addresses, and using a different ICMP scheme.
Fix __mirror_gre_test() in the selftest itself to pass a source IP address.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intention behind this test is to make sure that qdisc limit is
correctly projected to the HW. However, first, due to rounding in the
qdisc, and then in the driver, the number cannot actually be accurate. And
second, the approach to testing this is to oversubscribe the port with
traffic generated on the same switch. The actual backlog size therefore
fluctuates.
In practice, this test proved to be noisier than the rest, and spuriously
fails every now and then. Increase the tolerance to 10 % to avoid these
issues.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the resource scale test checks a few cases, when the error code
resets between the cases. So for example, if one case fails and the
consecutive case passes, the error code eventually will fit the last test
and will be 0.
Save a new return code that will hold the 'or' return codes of all the
cases, so the final return code will consider all the cases.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the error return code of the failure condition is lost after
using an if statement, so the test doesn't fail when it should.
Remove the if statement that separates the condition and the error code
check, so the test won't always pass.
Fixes: abfce9e062 ("selftests: mlxsw: Reduce running time using offload indication")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the error return code of the failure condition is lost after
using an if statement, so the test doesn't fail when it should.
Remove the if statement that separates the condition and the error code
check, so the test won't always pass.
Fixes: 5154b1b826 ("selftests: mlxsw: Add a scale test for physical ports")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug introduced during the rework which cause non-zero backlog
being stuck at ETS. Introduce a selftest that would have caught the issue
earlier.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that two sampling rules cannot be configured on the same port with
the same trigger.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can only offload matchall rules that do not match on a
protocol. Test that matchall rules that match on a protocol are vetoed.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that unsupported resilient nexthop group configurations are
rejected and that offload / trap indication is correctly set on nexthop
buckets in a resilient group.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of nexthop buckets in a resilient nexthop group never
changes, so when the gateway address of a nexthop cannot be resolved,
the nexthop buckets are programmed to trap packets to the CPU in order
to trigger resolution. For example:
# ip nexthop add id 1 via 198.51.100.1 dev swp3
# ip nexthop add id 10 group 1 type resilient buckets 32
# ip nexthop bucket get id 10 index 0
id 10 index 0 idle_time 1.44 nhid 1 trap
Where 198.51.100.1 is a made-up IP.
Test that in this case packets are indeed trapped to the CPU via the
unresolved neigh trap.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
q_in_vni_veto.sh is not needed anymore because VxLAN with an 802.1ad
bridge and VxLAN with an 802.1d bridge can coexist.
Remove the test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure egress sampling configuration only fails on Spectrum-1, given
that mlxsw now supports it on Spectrum-{2,3}.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that packets are sampled when tc-sample is used with matchall
egress binding and flower classifier. Verify that when performing
sampling on egress the end-to-end latency is reported as metadata.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that packets are sampled when tc-sample is used and that reported
metadata is correct. Two sets of hosts (with and without LAG) are used,
since metadata extraction in mlxsw is a bit different when LAG is
involved.
# ./tc_sample.sh
TEST: tc sample rate (forward) [ OK ]
TEST: tc sample rate (local receive) [ OK ]
TEST: tc sample maximum rate [ OK ]
TEST: tc sample group conflict test [ OK ]
TEST: tc sample iif [ OK ]
TEST: tc sample lag iif [ OK ]
TEST: tc sample oif [ OK ]
TEST: tc sample lag oif [ OK ]
TEST: tc sample out-tc [ OK ]
TEST: tc sample out-tc-occ [ OK ]
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test various aspects of psample functionality over netdevsim and in
particular test that the psample module correctly reports the provided
metadata.
Example:
# ./psample.sh
TEST: psample enable / disable [ OK ]
TEST: psample group number [ OK ]
TEST: psample metadata [ OK ]
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test various aspects of the resilient nexthop group offload API on top
of the netdevsim implementation. Both good and bad flows are tested.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Co-developed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cases to verify that when debugfs variable "fail_route_offload" is
set, notification with "rt_offload_failed" flag is received.
Extend the existing cases to verify that when sysctl
"fib_notify_on_flag_change" is set to 2, the kernel emits notifications
only for failed route installation.
$ ./fib_notifications.sh
TEST: IPv4 route addition [ OK ]
TEST: IPv4 route deletion [ OK ]
TEST: IPv4 route replacement [ OK ]
TEST: IPv4 route offload failed [ OK ]
TEST: IPv6 route addition [ OK ]
TEST: IPv6 route deletion [ OK ]
TEST: IPv6 route replacement [ OK ]
TEST: IPv6 route offload failed [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that setting lanes parameter is working.
Set max speed and max lanes in the list of advertised link modes,
and then try to set max speed with the lanes below max lanes if exists
in the list.
And then, test that setting number of lanes larger than max lanes fails.
Do the above for both autoneg on and off.
$ ./ethtool_lanes.sh
TEST: 4 lanes is autonegotiated [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
TEST: Autoneg off, 4 lanes detected during force mode [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add test to check fib notifications behavior.
The test checks route addition, route deletion and route replacement for
both IPv4 and IPv6.
When fib_notify_on_flag_change=0, expect single notification for route
addition/deletion/replacement.
When fib_notify_on_flag_change=1, expect:
- two notification for route addition/replacement, first without RTM_F_TRAP
and second with RTM_F_TRAP.
- single notification for route deletion.
$ ./fib_notifications.sh
TEST: IPv4 route addition [ OK ]
TEST: IPv4 route deletion [ OK ]
TEST: IPv4 route replacement [ OK ]
TEST: IPv6 route addition [ OK ]
TEST: IPv6 route deletion [ OK ]
TEST: IPv6 route replacement [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Run the test cases with both `fib_notify_on_flag_change` sysctls set to
'1', and then with both sysctls set to '0' to verify there are no
regressions in the test when notifications are added.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Query the maximum number of supported physical ports using devlink-resource
and test that this number can be reached by splitting each of the
splittable ports to its width. Test that an error is returned in case
the maximum number is exceeded.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
and bpf trees.
Current release - regressions:
- mt76: - usb: fix NULL pointer dereference in mt76u_status_worker
- sdio: fix NULL pointer dereference in mt76s_process_tx_queue
- net: ipa: fix interconnect enable bug
Current release - always broken:
- netfilter: ipset: fixes possible oops in mtype_resize
- ath11k: fix number of coding issues found by static analysis tools
and spurious error messages
Previous releases - regressions:
- e1000e: re-enable s0ix power saving flows for systems with
the Intel i219-LM Ethernet controllers to fix power
use regression
- virtio_net: fix recursive call to cpus_read_lock() to avoid
a deadlock
- ipv4: ignore ECN bits for fib lookups in fib_compute_spec_dst()
- net-sysfs: take the rtnl lock around XPS configuration
- xsk: - fix memory leak for failed bind
- rollback reservation at NETDEV_TX_BUSY
- r8169: work around power-saving bug on some chip versions
Previous releases - always broken:
- dcb: validate netlink message in DCB handler
- tun: fix return value when the number of iovs exceeds MAX_SKB_FRAGS
to prevent unnecessary retries
- vhost_net: fix ubuf refcount when sendmsg fails
- bpf: save correct stopping point in file seq iteration
- ncsi: use real net-device for response handler
- neighbor: fix div by zero caused by a data race (TOCTOU)
- bareudp: - fix use of incorrect min_headroom size
- fix false positive lockdep splat from the TX lock
- net: mvpp2: - clear force link UP during port init procedure
in case bootloader had set it
- add TCAM entry to drop flow control pause frames
- fix PPPoE with ipv6 packet parsing
- fix GoP Networking Complex Control config of port 3
- fix pkt coalescing IRQ-threshold configuration
- xsk: fix race in SKB mode transmit with shared cq
- ionic: account for vlan tag len in rx buffer len
- net: stmmac: ignore the second clock input, current clock framework
does not handle exclusive clock use well, other drivers
may reconfigure the second clock
Misc:
- ppp: change PPPIOCUNBRIDGECHAN ioctl request number to follow
existing scheme
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=N4/x
-----END PGP SIGNATURE-----
Merge tag 'net-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter, wireless and bpf
trees.
Current release - regressions:
- mt76: fix NULL pointer dereference in mt76u_status_worker and
mt76s_process_tx_queue
- net: ipa: fix interconnect enable bug
Current release - always broken:
- netfilter: fixes possible oops in mtype_resize in ipset
- ath11k: fix number of coding issues found by static analysis tools
and spurious error messages
Previous releases - regressions:
- e1000e: re-enable s0ix power saving flows for systems with the
Intel i219-LM Ethernet controllers to fix power use regression
- virtio_net: fix recursive call to cpus_read_lock() to avoid a
deadlock
- ipv4: ignore ECN bits for fib lookups in fib_compute_spec_dst()
- sysfs: take the rtnl lock around XPS configuration
- xsk: fix memory leak for failed bind and rollback reservation at
NETDEV_TX_BUSY
- r8169: work around power-saving bug on some chip versions
Previous releases - always broken:
- dcb: validate netlink message in DCB handler
- tun: fix return value when the number of iovs exceeds MAX_SKB_FRAGS
to prevent unnecessary retries
- vhost_net: fix ubuf refcount when sendmsg fails
- bpf: save correct stopping point in file seq iteration
- ncsi: use real net-device for response handler
- neighbor: fix div by zero caused by a data race (TOCTOU)
- bareudp: fix use of incorrect min_headroom size and a false
positive lockdep splat from the TX lock
- mvpp2:
- clear force link UP during port init procedure in case
bootloader had set it
- add TCAM entry to drop flow control pause frames
- fix PPPoE with ipv6 packet parsing
- fix GoP Networking Complex Control config of port 3
- fix pkt coalescing IRQ-threshold configuration
- xsk: fix race in SKB mode transmit with shared cq
- ionic: account for vlan tag len in rx buffer len
- stmmac: ignore the second clock input, current clock framework does
not handle exclusive clock use well, other drivers may reconfigure
the second clock
Misc:
- ppp: change PPPIOCUNBRIDGECHAN ioctl request number to follow
existing scheme"
* tag 'net-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits)
net: dsa: lantiq_gswip: Fix GSWIP_MII_CFG(p) register access
net: dsa: lantiq_gswip: Enable GSWIP_MII_CFG_EN also for internal PHYs
net: lapb: Decrease the refcount of "struct lapb_cb" in lapb_device_event
r8169: work around power-saving bug on some chip versions
net: usb: qmi_wwan: add Quectel EM160R-GL
selftests: mlxsw: Set headroom size of correct port
net: macb: Correct usage of MACB_CAPS_CLK_HW_CHG flag
ibmvnic: fix: NULL pointer dereference.
docs: networking: packet_mmap: fix old config reference
docs: networking: packet_mmap: fix formatting for C macros
vhost_net: fix ubuf refcount incorrectly when sendmsg fails
bareudp: Fix use of incorrect min_headroom size
bareudp: set NETIF_F_LLTX flag
net: hdlc_ppp: Fix issues when mod_timer is called while timer is running
atlantic: remove architecture depends
erspan: fix version 1 check in gre_parse_header()
net: hns: fix return value check in __lb_other_process()
net: sched: prevent invalid Scell_log shift count
net: neighbor: fix a crash caused by mod zero
ipv4: Ignore ECN bits for fib lookups in fib_compute_spec_dst()
...
The test was setting the headroom size of the wrong port. This was not
visible because of a firmware bug that canceled this bug.
Set the headroom size of the correct port, so that the test will pass
with both old and new firmware versions.
Fixes: bfa804784e ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20201230114251.394009-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Use /usr/bin/env for shebang lines in scripts
- Remove useless -Wnested-externs warning flag
- Update documents
- Refactor log handling in modpost
- Stop building modules without MODULE_LICENSE() tag
- Make the insane combination of 'static' and EXPORT_SYMBOL an error
- Improve genksyms to handle _Static_assert()
-----BEGIN PGP SIGNATURE-----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=+27V
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Use /usr/bin/env for shebang lines in scripts
- Remove useless -Wnested-externs warning flag
- Update documents
- Refactor log handling in modpost
- Stop building modules without MODULE_LICENSE() tag
- Make the insane combination of 'static' and EXPORT_SYMBOL an error
- Improve genksyms to handle _Static_assert()
* tag 'kbuild-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
Documentation/kbuild: Document platform dependency practises
Documentation/kbuild: Document COMPILE_TEST dependencies
genksyms: Ignore module scoped _Static_assert()
modpost: turn static exports into error
modpost: turn section mismatches to error from fatal()
modpost: change license incompatibility to error() from fatal()
modpost: turn missing MODULE_LICENSE() into error
modpost: refactor error handling and clarify error/fatal difference
modpost: rename merror() to error()
kbuild: don't hardcode depmod path
kbuild: doc: document subdir-y syntax
kbuild: doc: clarify the difference between extra-y and always-y
kbuild: doc: split if_changed explanation to a separate section
kbuild: doc: merge 'Special Rules' and 'Custom kbuild commands' sections
kbuild: doc: fix 'List directories to visit when descending' section
kbuild: doc: replace arch/$(ARCH)/ with arch/$(SRCARCH)/
kbuild: doc: update the description about kbuild Makefiles
Makefile.extrawarn: remove -Wnested-externs warning
tweewide: Fix most Shebang lines
Add tests to ensure that the forbidden and unsupported cases are indeed
vetoed by mlxsw driver.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change every shebang which does not need an argument to use /usr/bin/env.
This is needed as not every distro has everything under /usr/bin,
sometimes not even bash.
Signed-off-by: Finn Behrens <me@kloenk.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Test that the reference count of a router interface (RIF) configured for
a LAG is incremented / decremented when ports join / leave the LAG. Use
the offload indication on routes configured on the RIF to understand if
it was created / destroyed.
The test fails without the previous patch.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that each veto that was added in the previous patch, is indeed
vetoed.
$ ./q_in_q_veto.sh
TEST: create 802.1ad vlan upper on top of a front panel [ OK ]
TEST: create 802.1ad vlan upper on top of a bridge port [ OK ]
TEST: create 802.1ad vlan upper on top of a lag [ OK ]
TEST: create 802.1ad vlan upper on top 802.1q bridge [ OK ]
TEST: create 802.1ad vlan upper on top 802.1ad bridge [ OK ]
TEST: create 802.1q vlan upper on top 802.1ad bridge [ OK ]
TEST: create vlan upper on top of front panel enslaved to 802.1ad bridge
[ OK ]
TEST: create vlan upper on top of lag enslaved to 802.1ad bridge [ OK ]
TEST: enslave front panel with vlan upper to 802.1ad bridge [ OK ]
TEST: enslave lag with vlan upper to 802.1ad bridge [ OK ]
TEST: IP address addition to 802.1ad bridge [ OK ]
TEST: switch bridge protocol [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that packets hitting a blackhole nexthop are trapped to the CPU
when the trap is enabled. Test that packets are not reported when the
trap is disabled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test the mlxsw allows blackhole nexthops to be installed and that the
nexthops are marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that unsupported nexthop objects are rejected and that offload
indication is correctly set on: nexthop objects, nexthop group objects
and routes associated these objects.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add scripts to test ring and coalesce settings
of netdevsim.
Signed-off-by: Antonio Cardace <acardace@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As pointed out by Michal Kubecek, getting the name
with the previous approach was racy, it's better
and easier to get the name of the device with this
patch's approach.
Essentialy the function doesn't need to exist
anymore as it's a simple 'ls' command.
Signed-off-by: Antonio Cardace <acardace@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Factor out some useful functions so that they can be reused
by other ethtool-netdevsim scripts.
Signed-off-by: Antonio Cardace <acardace@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test various aspects of the nexthop offload API on top of the netdevsim
implementation. Both good and bad flows are tested.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a test that changes a VLAN ID from 200 to 300.
We also need to modify the preferences of the filters installed for the
other rules so that they are unique, because we now install the "tc-vlan
modify" filter in VCAP IS1 only temporarily, and we need to perform the
deletion by filter preference number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide an example script which can be used as a skeleton for offloading
TCAM rules in the Ocelot switches.
Not all actions are demoed, mostly because of difficulty to automate
this from a single board.
For example, policing. We can set up an iperf3 UDP server and client and
measure throughput at destination. But at least with DSA setups, network
namespacing the individual ports is not possible because all switch
ports are handled by the same DSA master. And we cannot assume that the
target platform (an embedded board) has 2 other non-switch generator
ports, we need to work with the generator ports as switch ports (this is
the reason why mausezahn is used, and not IP traffic like ping). When
somebody has an idea how to test policing, that can be added to this
test.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test for PFC. Runs 10MB of traffic through a bottleneck and checks
that none of it gets lost.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test for headroom configuration. This covers projection of ETS
configuration to ingress, PFC, adjustments for MTU, the qdisc / TC
mode and the effect of egress SPAN session on buffer configuration.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlnx_qos is a script for configuration of DCB. Despite the name it is not
actually Mellanox-specific in any way. It is currently the only ad-hoc tool
available (in contrast to a daemon that manages an interface on an ongoing
basis). However, it is very verbose and parsing out error messages is not
really possible. Add a wrapper that makes it easier to use the tool.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing pool type from static to dynamic causes reinterpretation of
threshold values. They therefore need to be saved before pool type is
changed, then the pool type can be changed, and then the new values need
to be set up.
For that reason, set cannot subsume save, because it would be saving the
wrong thing, with possibly a nonsensical value, and restore would then fail
to restore the nonsensical value.
Thus extract a _save() from each of the relevant _set()'s. This way it is
possible to save everything up front, then to tweak it, and then restore in
the required order.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check UDP_TUNNEL_NIC_INFO_STATIC_IANA_VXLAN works as expected.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test run of checks validating the shared UDP tunnel port
tables function as we expect.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ethtool" debugfs directory holds per-netdev knobs, so move
it from the device instance directory to the port directory.
This fixes the following warning when creating multiple ports:
debugfs: Directory 'ethtool' with parent 'netdevsim1' already present!
Fixes: ff1f7c17fb ("netdevsim: add pause frame stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink interface recently gained support for a new "overwrite mask"
parameter that allows specifying how various sub-sections of a flash
component are modified when updating.
Add support for this to netdevsim, to enable easily testing the
interface. Make the allowed overwrite mask values controllable via
a debugfs parameter. This enables testing a flow where the driver
rejects an unsupportable overwrite mask.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the empty nest is reported even without stats.
Make sure reporting only selected stats works fine.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the test takes about 626 seconds to complete because of an
inefficient use of the device's TCAM. Reduce the runtime to 202 seconds
by inserting all the flower filters with the same preference and mask,
but with a different key.
In particular, this reduces the deletion of the qdisc (which triggers
the deletion of all the filters) from 66 seconds to 0.2 seconds. This
prevents various netlink requests from user space applications (e.g.,
systemd-networkd) from timing-out because RTNL is not held for too long
anymore.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current combination of rate and burst size does not adhere to
Spectrum-{2,3} limitation which states that the minimum burst size
should be 40% of the rate.
Increase the burst size in order to honor above mentioned limitation and
avoid intermittent failures of this test case on Spectrum-{2,3}.
Remove the first sub-test case as the variation in number of received
packets is simply too large to reliably test it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current combination of rate and burst size does not adhere to
Spectrum-{2,3} limitation which states that the minimum burst size
should be 40% of the rate.
Increase the burst size in order to honor above mentioned limitation and
avoid intermittent failures of this test case on Spectrum-{2,3}.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-{2,3} the required accuracy is +/-10%.
Align the test to this requirement so that it can reliably pass on these
platforms.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest for RED early_drop and mark qevents when a trap action is
attached at the associated block.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that policers shared by different tc filters are correctly
reference counted by observing policers' occupancy via devlink-resource.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Query the maximum number of supported policers using devlink-resource
and test that this number can be reached by configuring tc filters with
police action. Test that an error is returned in case the maximum number
is exceeded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that upper and lower limits on rate and burst size imposed by the
device are rejected by the kernel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a selftest for offloading a mirror action attached to the block
associated with RED early_drop qevent.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add validating the UDP tunnel infra works.
$ ./udp_tunnel_nic.sh
PASSED all 383 checks
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generate packets matching the various control traps and check that the
traps' stats increase accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To align with recent recommended values. Will be configurable by future
patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from iputils s20190709 (used in Fedora 31), arping does not
support timeout being specified as a decimal:
$ arping -c 1 -I swp1 -b 192.0.2.66 -q -w 0.1
arping: invalid argument: '0.1'
Previously, such timeouts were rounded to an integer.
Fix this by specifying the timeout as an integer.
Fixes: a5ee171d08 ("selftests: mlxsw: qos_mc_aware: Add a test for UC awareness")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable is used by log_test() to check if the test case completely
successfully or not. In case it is not initialized at the start of a
test case, it is possible for the test case to fail despite not
encountering any errors.
Example:
```
...
TEST: Trap group statistics [ OK ]
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
TEST: Trap policer binding [FAIL]
Policer drop counter was not incremented
```
Failure of trap_policer_test() caused trap_policer_bind_test() to fail
as well.
Fix by adding missing initialization of the variable.
Fixes: 5fbff58e27 ("selftests: netdevsim: Add test cases for devlink-trap policers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be derived dynamically from the trap's name, so drop it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up after recent fixes, move address calculations
around and change the variable init, so that we can have
just one start_offset == end_offset check.
Make the check a little stricter to preserve the -EINVAL
error if requested start offset is larger than the region
itself.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that the drive restricts incorrect order of inserted matchall
vs. flower rules.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check that matchall rules with sample actions are not possible to be
inserted to egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The file is about to contain matchall restrictions too, so change the
name to make it more generic.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently users have to choose a free snapshot id before
calling DEVLINK_CMD_REGION_NEW. This is potentially racy
and inconvenient.
Make the DEVLINK_ATTR_REGION_SNAPSHOT_ID optional and try
to allocate id automatically. Send a message back to the
caller with the snapshot info.
Example use:
$ devlink region new netdevsim/netdevsim1/dummy
netdevsim/netdevsim1/dummy: snapshot 1
$ id=$(devlink -j region new netdevsim/netdevsim1/dummy | \
jq '.[][][][]')
$ devlink region dump netdevsim/netdevsim1/dummy snapshot $id
[...]
$ devlink region del netdevsim/netdevsim1/dummy snapshot $id
v4:
- inline the notification code
v3:
- send the notification only once snapshot creation completed.
v2:
- don't wrap the line containing extack;
- add a few sentences to the docs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are 3 SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your current
tree, that should be trivial to handle (one file modified by two things,
one file deleted.)
All 3 of these have been in linux-next for a while, with no reported
issues other than the merge conflict.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodg5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykySQCgy9YDrkz7nWq6v3Gohl6+lW/L+rMAnRM4uTZm
m5AuCzO3Azt9KBi7NL+L
=2Lm5
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
Add test cases that verify that each registered packet trap policer:
* Honors that imposed limitations of rate and burst size
* Able to police trapped packets to the specified rate
* Able to police trapped packets to the specified burst size
* Able to be unbound from its trap group
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test cases for packet trap policer set / show commands as well as
for the binding of these policers to packet trap groups.
Both good and bad flows are tested for maximum coverage.
v2:
* Add test case with new 'fail_trap_policer_set' knob
* Add test case for partially modified trap group
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health reporters should be registered with auto recover set to true.
Align dummy reporter behaviour with that, as in later patch the option to
set auto recover behaviour will be removed.
In addition, align netdevsim selftest to the new default value.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the .snapshot region operation for the dummy data region. This
enables a region snapshot to be taken upon request via the new
DEVLINK_CMD_REGION_SNAPSHOT command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DSCP is updated through an offloaded pedit action, DSCP rewrite on
egress should be disabled. Add a test that check that it is so.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests for mlxsw hw_stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the change that made the code to query counter bank size from device
instead of using hard-coded value, the number of available counters
changed for Spectrum-2. Adjust the limit in the selftests.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend RED testsuite to cover the new nodrop mode of RED-ECN. This test is
really similar to ECN test, diverging only in the last step, where UDP
traffic should go to backlog instead of being dropped. Thus extract a
common helper, ecn_test_common(), make do_ecn_test() into a relatively
simple wrapper, and add another one, do_ecn_nodrop_test().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the SW-datapath ETS selftests use "ip link" stats to obtain the
number of packets that went through a given band. mlxsw then uses ethtool
per-priority counters.
Instead, change both to use qdiscs. In SW datapath this is the obvious
choice, and now that mlxsw offloads FIFO, this should work on the offloaded
datapath as well. This has the effect of verifying that the FIFO offload
works.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hand-coding the busywait() predicate, use the until_counter_is()
introduced recently.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
until_counter_is() currently takes as an argument a number and the
condition holds when the current counter value is >= that number. Make the
function more generic by taking a partial expression instead of just the
number.
Convert the two existing users.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale test for Spectrum-2 should be invoked for Spectrum-2 and
Spectrum-3. Add the appropriate device ID.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the test inserts X /32 routes and for each route it is
testing that a packet sent from the first host is received by the second
host, which is very time-consuming.
Instead only validate the offload flag of each route and get the same result.
Wait between the creation of the routes and the offload validation in
order to make sure that all the routes were successfully offloaded.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding a given number of flower rules for different IPv6
addresses, the test generates traffic and ensures that each packet is
received, which is time-consuming.
Instead, test the offload indication of the tc flower rules and reduce
the running time by half.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test the max shared buffer occupancy for port's pool and port's TC's (using
different types of packets).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlxsw lib for common defines, helpers etc.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test physical ports' shared buffer configuration options using random
values related to a specific configuration option. There are 3
configuration options: pool, TC bind and portpool.
Each sub-test, test a different configuration option and random the related
values as the follow:
* For pools, pool's size will be randomized.
* For TC bind, pool number and threshold will be randomized.
* For portpools, threshold will be randomized.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rtnetlink test uses offload indication checks.
Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan test uses offload indication checks.
Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blackhole routes test uses offload indication checks.
Use busywait helper and wait until the routes offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test checks that packets are trapped when they should egress a
router interface (RIF) that has become disabled. This is a temporary
state in a RIF's deletion sequence.
Currently, the test deletes the RIF by flushing all the IP addresses
configured on the associated netdev (br0). However, this is racy, as
this also flushes all the routes pointing to the netdev and if the
routes are deleted from the device before the RIF is disabled, then no
packets will try to egress the disabled RIF and the trap will not be
triggered.
Instead, trigger the deletion of the RIF by unlinking the mlxsw port
from the bridge that is backing the RIF. Unlike before, this will not
cause the kernel to delete the routes pointing to the bridge.
Note that due to current mlxsw locking scheme the RIF is always deleted
first, but this is going to change.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include test of forbidding to have multiple mirror actions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include test of forbidding to have redirect rule on egress-bound block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests that below the queue minimum length, there is no dropping /
marking, and above max, everything is dropped / marked.
The test is structured as a core file with topology and test code, and
three wrappers: one for RED used as a root Qdisc, and two for
testing (W)RED under PRIO and ETS.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing devlink trap test to include metadata type for flow
action cookie.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test to check functionality of ACL traps.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the helpers assume pref 1 and handle 101. Make that explicit
and pass the values from callers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include test of forbidding to have drop rule on mixed-bound
shared block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when two VXLAN tunnels with conflicting configurations (i.e.,
different TTL) are enslaved to the same VLAN-aware bridge, then the
enslavement of a port to the bridge is denied.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes, the VXLAN tunnel will be offloaded regardless if
any local ports are member in the FID or not. Adjust the test to make
sure the tunnel is offloaded in this case.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver supports a single VLAN-aware bridge. Test that the
enslavement of a port to the second VLAN-aware bridge fails with an
extack.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that creation of a bridge (both VLAN-aware and VLAN-unaware) fails
with an extack when a VXLAN device with an unsupported configuration is
already enslaved to it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of a VLAN on a bridge slave prompts the driver to have the
local port in question join the FID corresponding to this VLAN.
Before recent changes, the operation of joining the FID would also mean
that the driver would enable VXLAN tunneling if a VXLAN device was also
member in the VLAN. In case the configuration of the VXLAN tunnel was
not supported, an extack error would be returned.
Since the operation of joining the FID no longer means that VXLAN
tunneling is potentially enabled, the test is no longer relevant. Remove
it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that routes in the main table do not replace identical routes in
the local table and that routes in the local table do replace identical
routes in the main table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that runs traffic across a port throttled with TBF. The test
checks that the observed throughput is within +-5% from the installed
shaper.
To allow checking both the software datapath and the offloaded one, make
the test suitable for inclusion from driver-specific wrapper. Introduce
such wrappers for mlxsw.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function humanize() is used for converting value in bits/s to a
human-friendly approximate value in Kbps, Mbps or Gbps. There is nothing
hardware-specific in that, so move the function to lib.sh.
Similarly for the rate() function, which just does a bit of math to
calculate a rate, given two counter values and a time interval.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that the trap is triggered under the right conditions and that
devlink counters increase when action is trap.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that the trap is triggered under the right conditions and that
devlink counters increase.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that the trap is triggered under the right conditions and that
devlink counters increase.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test cases to check that packets routed through disabled RIFs and
packets routed from disabled RIFs are dropped and devlink counters
increase when the action is trap.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mausezahn does not recognize "own" as a keyword on source IP address. As a
result, the MC stream is not running at all, and therefore no UC
degradation can be observed even in principle.
Fix the invocation, and tighten the test: due to the minimum shaper
configured at the MC TCs, we always expect about 20% degradation. Fail the
test if it is lower.
Fixes: 573363a68f ("selftests: mlxsw: Add qos_lib.sh")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reported-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test reuses the common FIB offload tests in order to make sure that
mlxsw correctly implements FIB offload.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test various aspects of the FIB offload API on top of the netdevsim
implementation. Both good and bad flows are tested.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send non-IP traffic to a port and observe that it gets prioritized
according to the lldptool app=$prio,1,0 rules.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests the newly-added ETS Qdisc. It runs two to three streams of
traffic, each with a different priority. ETS Qdisc is supposed to allocate
bandwidth according to the DRR algorithm and given weights. After running
the traffic for a while, counters are compared for each stream to check
that the expected ratio is in fact observed.
In order for the DRR process to kick in, a traffic bottleneck must exist in
the first place. In slow path, such bottleneck can be implemented by
wrapping the ETS Qdisc inside a TBF or other shaper. This might however
make the configuration unoffloadable. Instead, on HW datapath, the
bottleneck would be set up by lowering port speed and configuring shared
buffer suitably.
Therefore the test is structured as a core component that implements the
testing, with two wrapper scripts that implement the details of slow path
resp. fast path configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions are used for starting several streams of traffic, and
then stopping them later. They will be handy for the test coverage of ETS
Qdisc. Move them from mlxsw-specific qos_lib.sh to the generic lib.sh.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale test for Spectrum-2 should only be invoked for Spectrum-2.
Skip the test otherwise.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as for Spectrum-1, test the ability to add the maximum number of
routes possible to the switch.
Invoke the test from the 'resource_scale' wrapper script.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw does not support VXLAN devices with a physical device attached and
vetoes such configurations upon enslavement to an offloaded bridge.
Commit 0ce1822c2a ("vxlan: add adjacent link to limit depth level")
changed the VXLAN device to be an upper of the physical device which
causes mlxsw to veto the creation of the VXLAN device with "Unknown
upper device type".
This is OK as this configuration is not supported, but it prevents us
from testing bad flows involving the enslavement of VXLAN devices with a
physical device to a bridge, regardless if the physical device is an
mlxsw netdev or not.
Adjust the test to use a dummy device as a physical device instead of a
mlxsw netdev.
Fixes: 0ce1822c2a ("vxlan: add adjacent link to limit depth level")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test of 2 PAGEs size (exceeds devlink previous length limitation)
of binary data on a 'devlink health dump show' command. Set binary length
to 8192, issue a dump show command and clear it.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that each supported packet trap exception is triggered under the
right conditions.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that each supported packet trap is triggered under the right
conditions and that packets are indeed dropped and not forwarded.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proto parameter in order to enable the use of devlink_trap_cleanup()
in tests that use IPv6 protocol.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2_drops_test() is used to check that drop traps are functioning as
intended. Currently it is only used in the layer 2 test, but it is also
useful for the layer 3 test introduced in the subsequent patch.
l2_drops_cleanup() is used to clean configurations and kill mausezahn
proccess.
Export the functions to the common devlink library to allow it to be
re-used by future tests.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevsim object is reused by all the tests, but the resource
tests puts it into a broken state (failed reload in a different
namespace). Make sure it's fixed up at the end of that test
otherwise subsequent tests fail.
Fixes: b74c37fd35 ("selftests: netdevsim: add tests for devlink reload with resources")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the maximum number of tc flower filters that can be offloaded.
Currently, this value corresponds to the number of counters supported by
the driver.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add resource_scale test suitable for Spectrum-2.
Invoke the mirror_gre test and check that the advertised scale numbers
are indeed supported.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in Spectrum, use the number of analyzers taken from the devlink
command.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the number of analyzers taken from the devlink command, instead of
hard-coded value, in order to make the test more generic.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic tests to verify functionality of netdevsim reporters.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to verify netdevsim driver name returned by devlink dev info.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend netdevsim reload test by simulation of failures.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that creates netdevsim instance inside network namespace
and verifies that the related devlink instance and port netdevices
reside in the namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add couple of tests for devlink reload testing and also resource
limitations testing, along with devlink reload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is created, its VLAN filters are not cleared by the
firmware. This causes tagged packets to be later dropped by the ingress
STP filters, which default to DISCARD state.
The above did not matter much until commit b5ce611fd9 ("mlxsw:
spectrum: Add devlink-trap support") where we exposed the drop reason to
users.
Without this patch, the drop reason users will see is not consistent. If
a port is enslaved to a VLAN-aware bridge and a packet with an invalid
VLAN tries to ingress the bridge, it will be dropped due to ingress STP
filter. If the VLAN is later enabled and then disabled, the packet will
be dropped by the ingress VLAN filter despite the above being a
seemingly NOP operation.
Fix this by clearing all the VLAN filters during port initialization.
Adjust the test accordingly.
Fixes: b5ce611fd9 ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test generic devlink-trap functionality over mlxsw. These tests are not
specific to a single trap, but do not check the devlink-trap common
infrastructure either.
Currently, the only test case is device deletion (by reloading the
driver) while packets are being trapped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that each supported packet trap is triggered under the right
conditions and that packets are indeed dropped and not forwarded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test cases for devlink-trap on top of the netdevsim implementation.
The tests focus on the devlink-trap core infrastructure and user space
API. They test both good and bad flows and also dismantle of the netdev
and devlink device used to report trapped packets.
This allows device drivers to focus their tests on device-specific
functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test netdevsim devlink region implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test recently added netdevsim devlink param implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dedfde2fe1 ("mlxsw: spectrum_dcb: Configure DSCP map as the last
rule is removed") fixed a problem in mlxsw where last DSCP rule to be
removed remained in effect when DSCP rewrite was applied.
Add a selftest that covers this problem.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two tests have some problems in the global scope pollution and on
contrary, contain unnecessary local declarations. Fix them.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix some spelling typo in qos_mc_aware.sh
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kselftest update for Linux 5.3-rc1 consists of build failure
fixes and minor code cleaning patch to remove duplicate headers.
-----BEGIN PGP SIGNATURE-----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=azng
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest updates from Shuah Khan:
"This Kselftest update for Linux 5.3-rc1 consists of build failure
fixes and minor code cleaning patch to remove duplicate headers"
* tag 'linux-kselftest-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
rseq/selftests: Fix Thumb mode build failure on arm32
kselftests: cgroup: remove duplicated include from test_freezer.c
selftests: timestamping: Fix SIOCGSTAMP undeclared build failure
selftests: dma-buf: Adding kernel config fragment CONFIG_UDMABUF=y
The test case drivers/dma-buf/udmabuf need this kernel config enabled
CONFIG_UDMABUF=y
Signed-off-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Test that the offload indication for unicast routes is correctly set in
different scenarios. IPv4 support will be added in the future.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that IPv4 and IPv6 nexthops are correctly marked with offload
indication in response to neighbour events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilizes the devlink flash code.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This kselftest second update for Linux 5.2-rc1 consists of
Kselftest framework fixes from Shuah Khan
- kselftest framework bpf build/test workflow regression fix
- Fix to kselftest install to use default install path
- Fix to kselftest KBUILD_OUTPUT builds to not clutter main
KBUILD_OUTPUT directory with selftest objects
- .gitignore fixes from Kelsey Skunberg
- rseq selftests updates from Mathieu Desnoyers and Martin Schwidefsky:
They change the per-architecture pre-abort signatures to ensure those
are valid trap instructions.
The way exit points are presented to debuggers is enhanced, ensuring
all exit points are present, so debuggers don't have to disassemble
rseq critical section to properly skip over them.
Discussions with the glibc community is reaching a consensus of exposing
a __rseq_handled symbol from glibc to coexist with rseq early adopters.
Update the rseq selftest code to expose and use this symbol.
Support for compiling asm goto with clang is added with the
"-no-integrated-as" compiler switch, similarly to the top level kernel
Makefile.
- kselftest Makefile test run output refactoring and making test
output TAP13 compliant from Kees Cook:
This re-factors the selftest Makefiles to extract the test running logic
to be reused between "run_tests" and "emit_tests", while also fixing
up the test output to be TAP version 13 compliant:
- added "plan" line
- fixed result line syntax
- moved all test output to be "# "-prefixed as TAP "diagnostic"
lines
The prefixing code includes a fallback mode for limited execution
environments.
Additionally, the plan lines are fixed for all callers of kselftest.h.
-----BEGIN PGP SIGNATURE-----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=LZRz
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull more kselftest updates from Shuah Khan:
- kselftest framework bpf build/test workflow regression fix
- Fix to kselftest install to use default install path
- Fix to kselftest KBUILD_OUTPUT builds to not clutter main
KBUILD_OUTPUT directory with selftest objects
- .gitignore fixes (Kelsey Skunberg)
- rseq selftests updates (Mathieu Desnoyers and Martin Schwidefsky)
They change the per-architecture pre-abort signatures to ensure those
are valid trap instructions.
The way exit points are presented to debuggers is enhanced, ensuring
all exit points are present, so debuggers don't have to disassemble
rseq critical section to properly skip over them.
Discussions with the glibc community is reaching a consensus of
exposing a __rseq_handled symbol from glibc to coexist with rseq
early adopters. Update the rseq selftest code to expose and use this
symbol.
Support for compiling asm goto with clang is added with the
"-no-integrated-as" compiler switch, similarly to the top level
kernel Makefile.
- kselftest Makefile test run output refactoring and making test output
TAP13 compliant from Kees Cook:
This re-factors the selftest Makefiles to extract the test running
logic to be reused between "run_tests" and "emit_tests", while also
fixing up the test output to be TAP version 13 compliant:
- added "plan" line
- fixed result line syntax
- moved all test output to be "# "-prefixed as TAP "diagnostic"
lines
The prefixing code includes a fallback mode for limited execution
environments.
Additionally, the plan lines are fixed for all callers of
kselftest.h.
* tag 'linux-kselftest-5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (25 commits)
selftests: avoid KBUILD_OUTPUT dir cluttering with selftest objects
selftests: drivers: Create .gitignore to include /dma-buf/udmabuf
selftests: pidfd: Create .gitignore to include pidfd_test
selftests: fix bpf build/test workflow regression when KBUILD_OUTPUT is set
selftests: fix install target to use default install path
rseq/selftests: add -no-integrated-as for clang
rseq/selftests: mips: use break instruction for RSEQ_SIG
rseq/selftests: powerpc code signature: generate valid instructions
rseq/selftests: aarch64 code signature: handle big-endian environment
rseq/selftests: arm: use udf instruction for RSEQ_SIG
rseq/selftests: s390: use trap4 for RSEQ_SIG
rseq/selftests: x86: use ud1 instruction as RSEQ_SIG opcode
rseq/selftests: s390: use jg instruction for jumps outside of the asm
rseq/selftests: Use __rseq_handled symbol to coexist with glibc
rseq/selftests: Introduce __rseq_cs_ptr_array, rename __rseq_table to __rseq_cs
rseq/selftests: Add __rseq_exit_point_array section for debuggers
rseq/selftests: x86: Work-around bogus gcc-8 optimisation
selftests: Add test plan API to kselftest.h and adjust callers
selftests: Remove KSFT_TAP_LEVEL
selftests: Move test output to diagnostic lines
...
Create ../selftests/drivers/.gitignore which holds the following file name
created after compiling:
- /dma-buf/udmabuf
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Test that neighbour entries are marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that it is possible to set an IP address on a VRF and that it is
not vetoed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when strict priority is configured on a system, the
higher-priority traffic does actually win all the available bandwidth.
The test uses a similar approach to qos_mc_aware.sh to run and account
the traffic.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract reusable code from qos_mc_aware.sh and put into a new library.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test runs two streams of traffic from two independent ports to
create congestion on one egress port. It is necessary to configure the
shared buffer thresholds correctly, to make sure that there is traffic
from both streams in the shared buffer. Only then can the test actually
test prioritization among these streams.
Without this configuration, it is possible, that one of the streams
takes all of port-pool quota, and the other stream is not even admitted,
thus invalidating the result.
On Spectrum-1, this is not a problem, because MC traffic uses a separate
pool. But for Spectrum-2, MC and UC share the same pool, and the correct
configuration is important.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do insertions and removal of filters during rehash in higher volumes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checking of newly added trace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints. Use IPv6 addresses.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't source lib.sh 2 times and make the script work with ifnames
passed on the command line.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a simple topology consisting of two hosts directly connected to a
router. Make sure IPv4/IPv6 ping works and then add blackhole routes.
Test that ping fails and that the routes are marked as offloaded. Use a
simple tc filter to test that packets were dropped by the ASIC and not
trapped to the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current ping intervals are too short for running mirroring tests in
simulator. This leads to ping sending a follow-up ping before the reply
arrives, thus sending more than the requested 10 ICMP requests. This
traffic is seen at the counters, and causes spurious failures.
Bump interval and timeout numbers 5x in mirroring tests to address the
spurious failures.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timeout (2 seconds) proved to be too low for some (emulated)
systems where we run the tests.
Make the timeout configurable and default to 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the bug is fixed and we no longer have C-TCAM spill for two
keys that differ only in delta.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent fix in C-TCAM spillage for delta masks, the test stops to be
falsely positive. So fix it not to use delta by adding src_ip bits to the
masks. Alongside with that, use C-TCAM spill trace to see when the
spillage actually happens.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to specify number of trace hits and move helpers
to the beginning of the file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that externally learned FDB entries added from user space are
marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw doesn't implement offloading of all types of FDB entries that the
VXLAN driver supports. Test that such FDB entries are rejected. That
makes sure that the decision made by the existing validation code in
mlxsw propagates up the stack. It also exercises rollback functionality
in VXLAN, and tests that extack is returned.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test case for the issue fixed by previous commit. In case the
offloading of an unsupported VxLAN tunnel was triggered by adding the
mapped VLAN to a local port, then error should be returned to the user.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kselftest update for Linux 4.21-rc1 consists of:
- fixes, and improvements to the framework, and individual tests.
- a new media test for IR encoders from Sean Young.
- a new watchdog test option to find time left on a timer.
-----BEGIN PGP SIGNATURE-----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=H+yF
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest updates from Shuah Khan:
- fixes and improvements to the framework, and individual tests
- a new media test for IR encoders from Sean Young
- a new watchdog test option to find time left on a timer
* tag 'linux-kselftest-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Fix test errors related to lib.mk khdr target
fix dma-buf/udmabuf selftest
selftests: watchdog: fix spelling mistake "experies" -> "expires"
selftests: watchdog: Add gettimeleft command line arg
selftests: do not macro-expand failed assertion expressions
selftests/ftrace: Fix invalid SPDX identifiers
selftests: gpio: Find libmount with pkg-config if available
selftests: firmware: add CONFIG_FW_LOADER_USER_HELPER_FALLBACK to config
selftests: firmware: remove use of non-standard diff -Z option
media: rc: self test for IR encoders and decoders
Previous patches made it possible to create VLAN devices with VID 1 over
mlxsw ports. Adjust the test to verify such an operation succeeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
