Add support to enable flow-director filter when multiple TCs are
configured. Flow director filter can be configured using ethtool
(--config-ntuple option). When multiple TCs are configured, each
TC is mapped to an unique HW VSI. So VSI corresponding to queue
used in filter is identified and flow director context is updated
with correct VSI while configuring ntuple filter in HW.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We have a region for reading the contents of the NVM flash as
a snapshot. This region does not allow reading the Shadow RAM, as it
always passes the FLASH_ONLY bit to the low level firmware interface.
Add a separate shadow-ram region which will allow snapshot of the
current contents of the Shadow RAM. This data is built from the NVM
contents but is distinct as the device builds up the Shadow RAM during
initialization, so being able to snapshot its contents can be useful
when attempting to debug flash related issues.
Fix the comment description of the nvm-flash region which incorrectly
stated that it filled the shadow-ram region, and add a comment
explaining that the nvm-flash region does not actually read the Shadow
RAM.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the ice_stat_str() function which prints the string
representation of the ice_status error code. With upcoming changes
moving away from ice_status, there will be no need for this function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Allow support for 'enable_iwarp' and 'enable_roce' devlink params to turn
on/off iWARP or RoCE protocol support for E800 devices.
For example, a user can turn on iWARP functionality with,
devlink dev param set pci/0000:07:00.0 name enable_iwarp value true cmode runtime
This add an iWARP auxiliary rdma device, ice.iwarp.<>, under this PF.
A user request to enable both iWARP and RoCE under the same PF is rejected
since this device does not support both protocols simultaneously on the
same port.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a VF requests promiscuous mode and it's trusted and true promiscuous
mode is enabled the PF driver attempts to enable unicast and/or
multicast promiscuous mode filters based on the request. This is fine,
but there are a couple issues with the current code.
[1] The define to configure the unicast promiscuous mode mask also
includes bits to configure the multicast promiscuous mode mask, which
causes multicast to be set/cleared unintentionally.
[2] All 4 cases for enable/disable unicast/multicast mode are not
handled in the promiscuous mode message handler, which causes
unexpected results regarding the current promiscuous mode settings.
To fix [1] make sure any promiscuous mask defines include the correct
bits for each of the promiscuous modes.
To fix [2] make sure that all 4 cases are handled since there are 2 bits
(FLAG_VF_UNICAST_PROMISC and FLAG_VF_MULTICAST_PROMISC) that can be
either set or cleared. Also, since either unicast and/or multicast
promiscuous configuration can fail, introduce two separate error values
to handle each of these cases.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some devices have support for loading the PHY FW and in some cases this
can fail. When this fails, the FW will set the corresponding bit in the
link info structure. Also, the FW will send a link event if the correct
link event mask bit is set. Add support for printing an error message
when the PHY FW load fails during any link configuration flow and the
link event flow.
Since ice_check_module_power() is already doing something very similar
add a new function ice_check_link_cfg_err() so any failures reported in
the link info's link_cfg_err member can be printed in this one function.
Also, add the new ICE_FLAG_PHY_FW_LOAD_FAILED bit to the PF's flags so
we don't constantly print this error message during link polling if the
value never changed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement indirect notification mechanism to support offloading TC rules
on tunnel devices.
Keep indirect block list in netdev priv. Notification will call setting
tc cls flower function. For now we can offload only ingress type. Return
not supported for other flow block binder.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to add/delete channel specific filter using tc-flower.
For now, only supported action is "skip_sw hw_tc <tc_num>"
Filter criteria is specific to channel and it can be
combination of L3, L3+L4, L2+L4.
Example:
MATCH criteria Action
---------------------------
src and/or dest IPv4[6]/mask -> Forward to "hw_tc <tc_num>"
dest IPv4[6]/mask + dest L4 port -> Forward to "hw_tc <tc_num>"
dest MAC + dest L4 port -> Forward to "hw_tc <tc_num>"
src IPv4[6]/mask + src L4 port -> Forward to "hw_tc <tc_num>"
src MAC + src L4 port -> Forward to "hw_tc <tc_num>"
Adding tc-flower filter for channel using "hw_tc"
-------------------------------------------------
tc qdisc add dev <ethX> clsact
Above two steps are only needed the first time when adding
tc-flower filter.
tc filter add dev <ethX> protocol ip ingress prio 1 flower \
dst_ip 192.168.0.1/32 ip_proto tcp dst_port 5001 \
skip_sw hw_tc 1
tc filter show dev <ethX> ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1 hw_tc 1
eth_type ipv4
ip_proto tcp
dst_ip 192.168.0.1
dst_port 5001
skip_sw
in_hw in_hw_count 1
Delete specific filter:
-------------------------
tc filter del dev <ethx> ingress pref 1 handle 0x1 flower
Delete All filters:
------------------
tc filter del dev <ethX> ingress
Co-developed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support in driver for TC_QDISC_SETUP_MQPRIO. This support
enables instantiation of channels in HW using existing MQPRIO
infrastructure which is extended to be offloadable. This
provides a mechanism to configure dedicated set of queues for
each TC.
Configuring channels using "tc mqprio":
--------------------------------------
tc qdisc add dev <ethX> root mqprio num_tc 3 map 0 1 2 \
queues 4@0 4@4 4@8 hw 1 mode channel
Above command configures 3 TCs having 4 queues each. "hw 1 mode channel"
implies offload of channel configuration to HW. When driver processes
configuration received via "ndo_setup_tc: QDISC_SETUP_MQPRIO", each
TC maps to HW VSI with specified queues.
User can optionally specify bandwidth min and max rate limit per TC
(see example below). If shaper params like min and/or max bandwidth
rate limit are specified, driver configures VSI specific rate limiter
in HW.
Configuring channels and bandwidth shaper parameters using "tc mqprio":
----------------------------------------------------------------
tc qdisc add dev <ethX> root mqprio \
num_tc 4 map 0 1 2 3 queues 4@0 4@4 4@8 4@12 hw 1 mode channel \
shaper bw_rlimit min_rate 1Gbit 2Gbit 3Gbit 4Gbit \
max_rate 4Gbit 5Gbit 6Gbit 7Gbit
Command to view configured TCs:
-----------------------------
tc qdisc show dev <ethX>
Deleting TCs:
------------
tc qdisc del dev <ethX> root mqprio
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Go through the code base and use ice_for_each_* macros. While at it,
introduce ice_for_each_xdp_txq() macro that can be used for looping over
xdp_rings array.
Commit is not introducing any new functionality.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Under rare circumstances there might be a situation where a requirement
of having XDP Tx queue per CPU could not be fulfilled and some of the Tx
resources have to be shared between CPUs. This yields a need for placing
accesses to xdp_ring inside a critical section protected by spinlock.
These accesses happen to be in the hot path, so let's introduce the
static branch that will be triggered from the control plane when driver
could not provide Tx queue dedicated for XDP on each CPU.
Currently, the design that has been picked is to allow any number of XDP
Tx queues that is at least half of a count of CPUs that platform has.
For lower number driver will bail out with a response to user that there
were not enough Tx resources that would allow configuring XDP. The
sharing of rings is signalled via static branch enablement which in turn
indicates that lock for xdp_ring accesses needs to be taken in hot path.
Approach based on static branch has no impact on performance of a
non-fallback path. One thing that is needed to be mentioned is a fact
that the static branch will act as a global driver switch, meaning that
if one PF got out of Tx resources, then other PFs that ice driver is
servicing will suffer. However, given the fact that HW that ice driver
is handling has 1024 Tx queues per each PF, this is currently an
unlikely scenario.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.
Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.
Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.
Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.
Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.
Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Expose SMA and U.FL connectors as ptp_pins on E810-T based adapters and
allow controlling them.
E810-T adapters are equipped with:
- 2 external bidirectional SMA connectors
- 1 internal TX U.FL
- 1 internal RX U.FL
U.FL connectors share signal lines with the SMA connectors. The TX U.FL1
share the line with the SMA1 and the RX U.FL2 share line with the SMA2.
This dependence is controlled by the ice_verify_pin_e810t.
Additionally add support for the E810-T-based devices which don't use the
SMA/U.FL controller. If the IO expander is not detected don't expose pins
and use 2 predefined 1PPS input and output pins.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement ndo_setup_tc net device callback for TC HW offload on PF device.
ndo_setup_tc provides support for HW offloading various TC filters.
Add support for configuring the following filter with tc-flower:
- default L2 filters (src/dst mac addresses, ethertype, VLAN)
- variations of L3, L3+L4, L2+L3+L4 filters using advanced filters
(including ipv4 and ipv6 addresses).
Allow for adding/removing TC flows when PF device is configured in
eswitch switchdev mode. Two types of actions are supported at the
moment: FLOW_ACTION_DROP and FLOW_ACTION_REDIRECT.
Co-developed-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce the following ethtool operations for VF's representor:
-get_drvinfo
-get_strings
-get_ethtool_stats
-get_sset_count
-get_link
In all cases, existing operations were used with minor
changes which allow us to detect if ethtool op was called for
representor. Only VF VSI stats will be available for representor.
Implement ndo_get_stats64 for port representor. This will update
VF VSI stats and read them.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
New type of VSI has to be defined for switchdev control plane
VSI. Number of allocated Tx and Rx queue has to be equal to
amount of VFs, because each port representor should have one
Tx and Rx queue.
Also to not increase number of used irqs too much, control plane
VSI uses only one q_vector and handle all queues in one irq.
To allow handling all queues in one irq , new function to clean
msix for eswitch was introduced. This function will schedule napi
for each representor instead of scheduling it only for one like in
normal clean irq function.
Only one additional msix has to be requested. Always try to request
it in ice_ena_msix_range function.
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Switchdev environment has to be set up when user create VFs
and eswitch mode is switchdev. Release is done when user
delete all VFs.
Data path in this implementation is based on control plane VSI.
This VSI is used to pass traffic from port representors to
corresponding VFs and vice versa. Default TX rule has to be
added to forward packet to control plane VSI. This will redirect
packets from VFs which don't match other rules to control plane
VSI.
On RX side default rule is added on uplink VSI to receive all
traffic that doesn't match other rules. When setting switchdev
environment all other rules from VFs should be removed. Packet to
VFs will be forwarded by control plane VSI.
As VF without any mac rules can't send any packet because of
antispoof mechanism, VSI antispoof should be turned off on each VFs.
To send packet from representor to correct VSI, destination VSI
field in TX descriptor will have to be filled. Allow that by
setting destination override bit in control plane VSI security config.
Packet from VFs will be received on control plane VSI. Driver
should decide to which netdev forward the packet. Decision is
made based on src_vsi field from descriptor. There is a target
netdev list in control plane VSI struct which choose netdev
based on src_vsi number.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Port representor is used to manage VF from host side. To allow
it each created representor registers netdevice with random hw
address. Also devlink port is created for all representors.
Port representor name is created based on switch id or managed
by devlink core if devlink port was registered with success.
Open and stop ndo ops are implemented to allow managing the VF
link state. Link state is tracked in VF struct.
Struct ice_netdev_priv is extended by pointer to representor
field. This is needed to get correct representor from netdev
struct mostly used in ndo calls.
Implement helper functions to check if given netdev is netdev of
port representor (ice_is_port_repr_netdev) and to get representor
from netdev (ice_netdev_to_repr).
As driver mostly will create or destroy port representors on all
VFs instead of on single one, write functions to add and remove
representor for each VF.
Representor struct contains pointer to source VSI, which is VSI
configured on VF, backpointer to VF, backpointer to netdev,
q_vector pointer and metadata_dst which will be used in data path.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Keeping devlink port inside VSI data structure causes some issues.
Since VF VSI is released during reset that means that we have to
unregister devlink port and register it again every time reset is
triggered. With the new changes in devlink API it
might cause deadlock issues. After calling
devlink_port_register/devlink_port_unregister devlink API is going to
lock rtnl_mutex. It's an issue when VF reset is triggered in netlink
operation context (like setting VF MAC address or VLAN),
because rtnl_lock is already taken by netlink. Another call of
rtnl_lock from devlink API results in dead-lock.
By moving devlink port to PF/VF we avoid creating/destroying it
during reset. Since this patch, devlink ports are created during
ice_probe, destroyed during ice_remove for PF and created during
ice_repr_add, destroyed during ice_repr_rem for VF.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Write set and get eswitch mode functions used by devlink
ops. Use new pf struct member eswitch_mode to track current
eswitch mode in driver.
Changing eswitch mode is only allowed when there are no
VFs created.
Create new file for eswitch related code.
Add config flag ICE_SWITCHDEV to allow user to choose if
switchdev support should be enabled or disabled.
Use case examples:
- show current eswitch mode ('legacy' is the default one)
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode legacy
- move to 'switchdev' mode
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode
switchdev
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode switchdev
- create 2 VFs
[root@localhost]# echo 2 > /sys/class/net/ens4f1/device/sriov_numvfs
- unsuccessful attempt to change eswitch mode while VFs are created
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode legacy
devlink answers: Operation not supported
- destroy VFs
[root@localhost]# echo 0 > /sys/class/net/ens4f1/device/sriov_numvfs
- restore 'legacy' mode
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode legacy
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode legacy
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
DSCP a.k.a L3 QoS is only supported on certain devices. To enforce this,
this patch introduces a bitmap of features and helper functions.
The feature bitmap is set based on device IDs on driver init. Currently,
DSCP is the only feature in this bitmap, but there will be more in the
future. In the DCB netlink flow, check if the feature bit is set before
exercising DSCP.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are two cases where the current PF does not support RDMA
functionality. The first is if the NVM loaded on the device is set
to not support RDMA (common_caps.rdma is false). The second is if
the kernel bonding driver has included the current PF in an active
link aggregate.
When the driver has determined that this PF does not support RDMA, then
auxiliary devices should not be created on the auxiliary bus. Without
a device on the auxiliary bus, even if the irdma driver is present, there
will be no RDMA activity attempted on this PF.
Currently, in the reset flow, an attempt to create auxiliary devices is
performed without regard to the ability of the PF. There needs to be a
check in ice_aux_plug_dev (as the central point that creates auxiliary
devices) to see if the PF is in a state to support the functionality.
When disabling and re-enabling RDMA due to the inclusion/removal of the PF
in a link aggregate, we also need to set/clear the bit which controls
auxiliary device creation so that a reset recovery in a link aggregate
situation doesn't try to create auxiliary devices when it shouldn't.
Fixes: f9f5301e7e ("ice: Register auxiliary device to provide RDMA")
Reported-by: Yongxin Liu <yongxin.liu@windriver.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs are setup and torn down in quick succession, it is possible
that a VF is torn down by the PF while the VF's virtchnl requests are
still in the PF's mailbox ring. Processing the VF's virtchnl request
when the VF itself doesn't exist results in undefined behavior. Fix
this by adding a check to stop processing virtchnl requests when VF
teardown is in progress.
Fixes: ddf30f7ff8 ("ice: Add handler to configure SR-IOV")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.
If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.
Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.
Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-06-07
This series contains updates to virtchnl header file and ice driver.
Brett adds capability bits to virtchnl to specify whether a primary or
secondary MAC address is being requested and adds the implementation to
ice. He also adds storing of VF MAC address so that it will be preserved
across reboots of VM and refactors VF queue configuration to remove the
expectation that configuration be done all at once.
Krzysztof refactors ice_setup_rx_ctx() to remove configuration not
related to Rx context into a new function, ice_vsi_cfg_rxq().
Liwei Song extends the wait time for the global config timeout.
Salil Mehta refactors code in ice_vsi_set_num_qs() to remove an
unnecessary call when the user has requested specific number of Rx or Tx
queues.
Jesse converts define macros to static inlines for NOP configurations.
Jake adds messaging when devlink fails to read device capabilities and
when pldmfw cannot find the requested firmware. Adds a wait for reset
completion when reporting devlink info and reinitializes NVM during
rebuild to ensure values are current.
Ani adds detection and reporting of modules exceeding supported power
levels and changes an error message to a debug message.
Paul fixes a clang warning for deadcode.DeadStores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Requesting device firmware information while the device is busy cleaning
up after a reset can result in an unexpected failure:
This occurs because the command is attempting to access the device
AdminQ while it is down. Resolve this by having the command wait for
a while until the reset is complete. To do this, introduce
a reset_wait_queue and associated helper function "ice_wait_for_reset".
This helper will use the wait queue to sleep until the driver is done
rebuilding. Use of a wait queue is preferred because the potential sleep
duration can be several seconds.
To ensure that the thread wakes up properly, a new wake_up call is added
during all code paths which clear the reset state bits associated with
the driver rebuild flow.
Using this ensures that tools can request device information without
worrying about whether the driver is cleaning up from a reset.
Specifically, it is expected that a flash update could result in
a device reset, and it is better to delay the response for information
until the reset is complete rather than exit with an immediate failure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit c7a219048e ("ice: Remove xsk_buff_pool from VSI structure")
silently introduced a regression and broke the Tx side of AF_XDP in copy
mode. xsk_pool on ice_ring is set only based on the existence of the XDP
prog on the VSI which in turn picks ice_clean_tx_irq_zc to be executed.
That is not something that should happen for copy mode as it should use
the regular data path ice_clean_tx_irq.
This results in a following splat when xdpsock is run in txonly or l2fwd
scenarios in copy mode:
<snip>
[ 106.050195] BUG: kernel NULL pointer dereference, address: 0000000000000030
[ 106.057269] #PF: supervisor read access in kernel mode
[ 106.062493] #PF: error_code(0x0000) - not-present page
[ 106.067709] PGD 0 P4D 0
[ 106.070293] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 106.074721] CPU: 61 PID: 0 Comm: swapper/61 Not tainted 5.12.0-rc2+ #45
[ 106.081436] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 106.092027] RIP: 0010:xp_raw_get_dma+0x36/0x50
[ 106.096551] Code: 74 14 48 b8 ff ff ff ff ff ff 00 00 48 21 f0 48 c1 ee 30 48 01 c6 48 8b 87 90 00 00 00 48 89 f2 81 e6 ff 0f 00 00 48 c1 ea 0c <48> 8b 04 d0 48 83 e0 fe 48 01 f0 c3 66 66 2e 0f 1f 84 00 00 00 00
[ 106.115588] RSP: 0018:ffffc9000d694e50 EFLAGS: 00010206
[ 106.120893] RAX: 0000000000000000 RBX: ffff88984b8c8a00 RCX: ffff889852581800
[ 106.128137] RDX: 0000000000000006 RSI: 0000000000000000 RDI: ffff88984cd8b800
[ 106.135383] RBP: ffff888123b50001 R08: ffff889896800000 R09: 0000000000000800
[ 106.142628] R10: 0000000000000000 R11: ffffffff826060c0 R12: 00000000000000ff
[ 106.149872] R13: 0000000000000000 R14: 0000000000000040 R15: ffff888123b50018
[ 106.157117] FS: 0000000000000000(0000) GS:ffff8897e0f40000(0000) knlGS:0000000000000000
[ 106.165332] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 106.171163] CR2: 0000000000000030 CR3: 000000000560a004 CR4: 00000000007706e0
[ 106.178408] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 106.185653] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 106.192898] PKRU: 55555554
[ 106.195653] Call Trace:
[ 106.198143] <IRQ>
[ 106.200196] ice_clean_tx_irq_zc+0x183/0x2a0 [ice]
[ 106.205087] ice_napi_poll+0x3e/0x590 [ice]
[ 106.209356] __napi_poll+0x2a/0x160
[ 106.212911] net_rx_action+0xd6/0x200
[ 106.216634] __do_softirq+0xbf/0x29b
[ 106.220274] irq_exit_rcu+0x88/0xc0
[ 106.223819] common_interrupt+0x7b/0xa0
[ 106.227719] </IRQ>
[ 106.229857] asm_common_interrupt+0x1e/0x40
</snip>
Fix this by introducing the bitmap of queues that are zero-copy enabled,
where each bit, corresponding to a queue id that xsk pool is being
configured on, will be set/cleared within ice_xsk_pool_{en,dis}able and
checked within ice_xsk_pool(). The latter is a function used for
deciding which napi poll routine is executed.
Idea is being taken from our other drivers such as i40e and ixgbe.
Fixes: c7a219048e ("ice: Remove xsk_buff_pool from VSI structure")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Register ice client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the auxiliary driver (irdma) to attach to.
It allows to realize a single RDMA driver (irdma) capable of working with
multiple netdev drivers over multi-generation Intel HW supporting RDMA.
There is no load ordering dependencies between ice and irdma.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files. Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tracking of the rx_gro_dropped statistic was removed in
commit f73fc40327 ("ice: drop dead code in ice_receive_skb()").
Remove the associated variables and its reporting to ethtool stats.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.
enum ice_state is used to represent state information of the PF.
While some of these enum values can be use to represent VSI state,
it makes more sense to represent VSI state with its own enum. So
derive a new enum ice_vsi_state from ice_vsi_flags and ice_state
and use it. Also rename enum ice_state to ice_pf_state for clarity.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently ice_set/get_rss are used to set/get the RSS LUT and/or RSS
key. However nearly everywhere these functions are called only the LUT
or key are set/get. Also, making this change reduces how many things
ice_set/get_rss are doing. Fix this by adding ice_set/get_rss_lut and
ice_set/get_rss_key functions.
Also, consolidate all calls for setting/getting the RSS LUT and RSS Key
to use ice_set/get_rss_lut() and ice_set/get_rss_key().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, ice_vsi_setup_q_map() depends on the VSI's rss_size. However,
the Rx Queue Mapping section of the VSI context has no dependency on RSS.
Instead, limit the maximum number of Rx queues per TC based on the Rx
Queue mapping section of the VSI context, which currently allows for up
to 256 Rx queues per TC.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As per the spec, the WoL control word read from the NVM should be
interpreted as port numbers, and not PF numbers. So when checking
if WoL supported, use the port number instead of the PF ID.
Also, ice_is_wol_supported doesn't really need a pointer to the pf
struct, but just needs a pointer to the hw instance.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The original purpose of the ICE_DCBNL_DEVRESET was to protect
the driver during DCBNL device resets. But, the flow for
DCBNL device resets now consists of only calls up the stack
such as dev_close() and dev_open() that will result in NDO calls
to the driver. These will be handled with state changes from the
stack. Also, there is a problem of the dev_close and dev_open
being blocked by checks for reset in progress also using the
ICE_DCBNL_DEVRESET bit.
Since the ICE_DCBNL_DEVRESET bit is not necessary for protecting
the driver from DCBNL device resets and it is actually blocking
changes coming from the DCBNL interface, remove the bit from the
PF state and don't block driver function based on DCBNL reset in
progress.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a possibility of race between ice_open or ice_stop calls
performed by OS and reset handling routine both trying to modify VSI
resources. Observed scenarios:
- reset handler deallocates memory in ice_vsi_free_arrays and ice_open
tries to access it in ice_vsi_cfg_txq leading to driver crash
- reset handler deallocates memory in ice_vsi_free_arrays and ice_close
tries to access it in ice_down leading to driver crash
- reset handler clears port scheduler topology and sets port state to
ICE_SCHED_PORT_STATE_INIT leading to ice_ena_vsi_txq fail in ice_open
To prevent this additional checks in ice_open and ice_stop are
introduced to make sure that OS is not allowed to alter VSI config while
reset is in progress.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Krzysztof Goreczny <krzysztof.goreczny@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.
To enable returning FDIR completion status from ctrl_vsi Rx queue,
COMP_Queue and COMP_Report of FDIR filter programming descriptor
needs to be properly configured. After program request sent to ctrl_vsi
Tx queue, ctrl_vsi Rx queue interrupt will be triggered and
completion status will be returned.
Driver will first issue request in ice_vc_fdir_add_fltr(), then
pass FDIR context to the background task in interrupt service routine
ice_vc_fdir_irq_handler() and finally deal with them in
ice_flush_fdir_ctx(). ice_flush_fdir_ctx() will check the descriptor's
value, fdir context, and then send back virtual channel message to VF
by calling ice_vc_add_fdir_fltr_post(). An additional timer will be
setup in case of hardware interrupt timeout.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are going to enable FDIR configure for AVF through virtual channel.
The first step is to add helper functions to support control VSI setup.
A control VSI will be allocated for a VF when AVF creates its
first FDIR rule through ice_vf_ctrl_vsi_setup().
The patch will also allocate FDIR rule space for VF's control VSI.
If a VF asks for flow director rules, then those should come entirely
from the best effort pool and not from the guaranteed pool. The patch
allow a VF VSI to have only space in the best effort rules.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
DCBX_CAP bits were not being adjusted when switching
between SW and FW controlled LLDP.
Adjust bits to correctly indicate which mode the
LLDP logic is in.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create set scheduler aggregator node and move for VSIs into respective
scheduler node. Max children per aggregator node is 64.
There are two types of aggregator node(s) created.
1. dedicated node for PF and _CTRL VSIs
2. dedicated node(s) for VFs.
As part of reset and rebuild, aggregator nodes are recreated and VSIs
are moved to respective aggregator node.
Having related VSIs in respective tree avoid starvation between PF and VF
w.r.t Tx bandwidth.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Co-developed-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Victor Raj <victor.raj@intel.com>
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the framework and initial implementation for receiving and processing
netdev bonding events. This is only the software support and the
implementation of the HW offload for bonding support will be coming at a
later time. There are some architectural gaps that need to be closed
before that happens.
Because this is a software only solution that supports in kernel bonding,
SR-IOV is not supported with this implementation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current implementation of netdev already contains xsk_buff_pools.
We no longer have to contain these structures in ice_vsi.
Refactor the code to operate on netdev-provided xsk_buff_pools.
Move scheduling napi on each queue to a separate function to
simplify setup function.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in
struct ice_res_tracker, instead of a one-element array and use the
struct_size() helper to calculate the size for the allocations.
Also, notice that the code below suggests that, currently, two too many
bytes are being allocated with devm_kzalloc(), as the total number of
entries (pf->irq_tracker->num_entries) for pf->irq_tracker->list[] is
_vectors_ and sizeof(*pf->irq_tracker) also includes the size of the
one-element array _list_ in struct ice_res_tracker.
drivers/net/ethernet/intel/ice/ice_main.c:3511:
3511 /* populate SW interrupts pool with number of OS granted IRQs. */
3512 pf->num_avail_sw_msix = (u16)vectors;
3513 pf->irq_tracker->num_entries = (u16)vectors;
3514 pf->irq_tracker->end = pf->irq_tracker->num_entries;
With this change, the right amount of dynamic memory is now allocated
because, contrary to one-element arrays which occupy at least as much
space as a single object of the type, flexible-array members don't
occupy such space in the containing structure.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9-rc1/process/deprecated.html#zero-length-and-one-element-arrays
Built-tested-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
vlan_ena was introduced to track whether VLAN filters are enabled on
the device, but
1) checking for num_vlan > 1 already gives us this information, and is
currently used in this way throughout the code
2) the logic for vlan_ena is broken when multiple VLANs are active
Just remove vlan_ena and use num_vlan instead.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.
In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.
If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.
This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.
Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.
Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.
Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.
There are three classes of kdoc warnings fixed:
- cannot understand function prototype: 'x'
- Excess function parameter 'x' description in 'y'
- Function parameter or member 'x' not described in 'y'
All of the changes were trivial comment updates on
function headers.
Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
xargs scripts/kernel-doc -none
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com
Display and count some useful hot-path statistics. The usefulness is as
follows:
- tx_restart: use to determine if the transmit ring size is too small or
if the transmit interrupt rate is too low.
- rx_gro_dropped: use to count drops from GRO layer, which previously were
completely uncounted when occurring.
- tx_busy: use to determine when the driver is miscounting number of
descriptors needed for an skb.
- tx_timeout: as our other drivers, count the number of times we've reset
due to timeout because the kernel only prints a warning once per netdev.
Several of these were already counted but not displayed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new devlink region used for capturing a snapshot of the device
capabilities buffer which is reported by the firmware over the AdminQ.
This information can useful in debugging driver and firmware
interactions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Enable accelerated Receive Flow Steering (aRFS). It is used to steer Rx
flows to a specific queue. This functionality is triggered by the network
stack through ndo_rx_flow_steer and requires Flow Director (ntuple on) to
function.
The fltr_info is used to add/remove/update flow rules in the HW, the
fltr_state is used to determine what to do with the filter with respect
to HW and/or SW, and the flow_id is used in co-ordination with the
network stack.
The work for aRFS is split into two paths: the ndo_rx_flow_steer
operation and the ice_service_task. The former is where the kernel hands
us an Rx SKB among other items to setup aRFS and the latter is where
the driver adds/updates/removes filter rules from HW and updates filter
state.
In the Rx path the following things can happen:
1. New aRFS entries are added to the hash table and the state is
set to ICE_ARFS_INACTIVE so the filter can be updated in HW
by the ice_service_task path.
2. aRFS entries have their Rx Queue updated if we receive a
pre-existing flow_id and the filter state is ICE_ARFS_ACTIVE.
The state is set to ICE_ARFS_INACTIVE so the filter can be
updated in HW by the ice_service_task path.
3. aRFS entries marked as ICE_ARFS_TODEL are deleted
In the ice_service_task path the following things can happen:
1. New aRFS entries marked as ICE_ARFS_INACTIVE are added or
updated in HW.
and their state is updated to ICE_ARFS_ACTIVE.
2. aRFS entries are deleted from HW and their state is updated
to ICE_ARFS_TODEL.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a reset, Flow Director filters are cleared from the hardware.
Rebuild the filters using the software structures containing the filter
rules.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functionality for ethtool --show-ntuple, allowing for filters to be
displayed when set functionality is added. Add statistics related to
Flow Director matches and status.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.
Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vf_id variable is dealt with in the code in inconsistent
ways of sign usage, preventing compilation with -Werror=sign-compare.
Fix this problem in the code by always treating vf_id as unsigned, since
there are no valid values of vf_id that are negative.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.
In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.
There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.
Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When printing the ice status or AQ error codes, instead of printing out the
numerical value, provide the description of the error code. This provides
more info about the issue than a number.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement promiscuous support for VF VSIs. Behaviour of promiscuous support
is based on VF trust as well as the, introduced, vf-true-promisc flag.
A trusted VF with vf-true-promisc disabled will be the default VSI, which
means that all traffic without a matching destination MAC address in the
device's internal switch will be forwarded to this VF VSI.
A trusted VF with vf-true-promisc enabled will go into "true promiscuous
mode". This amounts to the VF receiving all ingress and egress traffic
that hits the device's internal switch.
An untrusted VF will only receive traffic destined for that VF.
The vf-true-promisc-support flag cannot be toggled while any VF is in
promiscuous mode. This flag should be set prior to loading the iavf driver
or spawning VF(s).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a boost TCAM entry for each tunnel port in order to get a tunnel
PTYPE. Update netdev feature flags and implement the appropriate logic to
get and set values for hardware offloads.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a devlink region for exposing the device's Non Volatime Memory flash
contents.
Support the recently added .snapshot operation, enabling userspace to
request a snapshot of the NVM contents via DEVLINK_CMD_REGION_NEW.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Begin implementing support for the devlink interface with the ice
driver.
The pf structure is currently memory managed through devres, via
a devm_alloc. To mimic this behavior, after allocating the devlink
pointer, use devm_add_action to add a teardown action for releasing the
devlink memory on exit.
The ice hardware is a multi-function PCIe device. Thus, each physical
function will get its own devlink instance. This means that each
function will be treated independently, with its own parameters and
configuration. This is done because the ice driver loads a separate
instance for each function.
Due to this, the implementation does not enable devlink to manage
device-wide resources or configuration, as each physical function will
be treated independently. This is done for simplicity, as managing
a devlink instance across multiple driver instances would significantly
increase the complexity for minimal gain.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF's mailbox receive queue is only 512 entries. This fine,
but considering that all VF's mailbox send queues funnel into the PF's
single mailbox receive queue, let's increase it to the maximum size. This
will help prevent any possible bottleneck/slowdown occurring from the PF's
mailbox receive queue being full.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, if there are bare-metal VFs passing traffic and the ice
driver is removed, there is a possibility of VFs triggering a Tx timeout
right before iavf_remove(). This is causing iavf_close() to not be
called because there is a check in the beginning of iavf_remove() that
bails out early if (adapter->state < IAVF_DOWN_PENDING). This makes it
so some resources do not get cleaned up. Specifically, free_irq()
is never called for data interrupts, which results in the following line
of code to trigger:
pci_disable_msix()
free_msi_irqs()
...
BUG_ON(irq_has_action(entry->irq + i));
...
To prevent the Tx timeout from occurring on the VF during driver unload
for ice and the iavf there are a few changes that are needed.
[1] Don't disable all active VF Tx/Rx queues prior to calling
pci_disable_sriov.
[2] Call ice_free_vfs() before disabling the service task.
[3] Disable VF resets when the ice driver is being unloaded by setting
the pf->state flag __ICE_VF_RESETS_DISABLED.
Changing [1] and [2] allow each VF driver's remove flow to successfully
send VIRTCHNL requests, which includes queue disable. This prevents
unexpected Tx timeouts because the PF driver is no longer forcefully
disabling queues.
Due to [1] and [2] there is a possibility that the PF driver will get a
VFLR or reset request over VIRTCHNL from a VF during PF driver unload.
Prevent that by doing [3].
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when the device runs out of MSI-X interrupts a cryptic and
unhelpful message is printed. This will cause confusion when hitting this
case. Fix this by clearing up the error message for both SR-IOV and non
SR-IOV use cases.
Also, make a few minor changes to increase clarity of variables.
1. Change per VF MSI-X and queue pair variables in the PF structure.
2. Use ICE_NONQ_VECS_VF when determining pf->num_msix_per_vf instead of
the magic number "1". This vector is reserved for the OICR.
All of the resource tracking functions were moved to avoid adding
any forward declaration function prototypes.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Unlike the XL710 series, 800-series hardware can allocate more than 4
MSI-X vectors per VF. This patch enables that functionality. We
dynamically allocate vectors and queues depending on how many VFs are
enabled. Allocating the maximum number of VFs replicates XL710
behavior with 4 queues and 4 vectors. But allocating a smaller number
of VFs will give you 16 queues and 16 vectors.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the PF VFs MDD event message to rate limit once per second and
report the total number Rx|Tx event count. Add support to print pending
MDD events that occur during the rate limit. The use of net_ratelimit did
not allow for per VF Rx|Tx granularity.
Additional PF MDD log messages are guarded by netif_msg_[rx|tx]_err().
Since VF RX MDD events disable the queue, add ethtool private flag
mdd-auto-reset-vf to configure VF reset to re-enable the queue.
Disable anti-spoof detection interrupt to prevent spurious events
during a function reset.
To avoid race condition do not make PF MDD register reads conditional
on global MDD result.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_xsk_umem(), variable qid which is later used as an array index,
is not validated for a possible boundary exceedance. Because of that,
a calling function might receive an invalid address, which causes
general protection fault when dereferenced.
To address this, add a boundary check to see if qid is greater than the
size of a UMEM array. Also, don't let user change vsi->num_xsk_umems
just by trying to setup a second UMEM if its value is already set up
(i.e. UMEM region has already been allocated for this VSI).
While at it, make sure that ring->zca.free pointer is always zeroed out
if there is no UMEM on a specified ring.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can't have more than one default VSI so prevent another VSI from
overwriting the current dflt_vsi. This was achieved by adding the
following functions:
ice_is_dflt_vsi_in_use()
- Used to check if the default VSI is already being used.
ice_is_vsi_dflt_vsi()
- Used to check if VSI passed in is in fact the default VSI.
ice_set_dflt_vsi()
- Used to set the default VSI via a switch rule
ice_clear_dflt_vsi()
- Used to clear the default VSI via a switch rule.
Also, there was no need to introduce any locking because all mailbox
events and synchronization of switch filters for the PF happen in the
service task.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many things wrong with the function
ice_set_vf_spoofchk().
1. The VSI being modified is the PF VSI, not the VF VSI.
2. We are enabling Rx VLAN pruning instead of Tx VLAN anti-spoof.
3. The spoofchk setting for each VF is not initialized correctly
or re-initialized correctly on reset.
To fix [1] we need to make sure we are modifying the VF VSI.
This is done by using the vf->lan_vsi_idx to index into the PF's
VSI array.
To fix [2] replace setting Rx VLAN pruning in ice_set_vf_spoofchk()
with setting Tx VLAN anti-spoof.
To Fix [3] we need to make sure the initial VSI settings match what
is done in ice_set_vf_spoofchk() for spoofchk=on. Also make sure
this also works for VF reset. This was done by modifying ice_vsi_init()
to account for the current spoofchk state of the VF VSI.
Because of these changes, Tx VLAN anti-spoof needs to be removed
from ice_cfg_vlan_pruning(). This is okay for the VF because this
is now controlled from the admin enabling/disabling spoofchk. For the
PF, Tx VLAN anti-spoof should not be set. This change requires us to
call ice_set_vf_spoofchk() when configuring promiscuous mode for
the VF which requires ice_set_vf_spoofchk() to move in order to prevent
a forward declaration prototype.
Also, add VLAN 0 by default when allocating a VF since the PF is unaware
if the guest OS is running the 8021q module. Without this, MDD events will
trigger on untagged traffic because spoofcheck is enabled by default. Due
to this change, ignore add/delete messages for VLAN 0 from VIRTCHNL since
this is added/deleted during VF initialization/teardown respectively and
should not be modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively. Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We use &pf->dev->pdev all over the code. Add a simple
macro to do this for us. When multiple de-references
like this are being done add a local struct device
variable.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement interface layer for the DCBNL subsystem. These are the functions
to support the callbacks defined in the dcbnl_rtnl_ops struct. These
callbacks are going to be used to interface with the DCB settings of the
device. Implementation of dcb_nl set functions and supporting SW DCB
functions.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.
Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.
In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.
This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
network stack is expecting the NET_SKB_PAD to be provided and
NET_IP_ALIGN can have a non-zero value (these can be typically equal
to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
buffer is implying the need for order 1 page, so that our page
recycling scheme can still be applied;
With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.
In the followup patch the headroom/tailroom computation logic will be
introduced.
This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add zero copy AF_XDP support. This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.
For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.
For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit. Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a few uses of kernel configuration flags from ice_lib.c by
introducing a new source file ice_base.c. Also move corresponding
function prototypes from ice_lib.h to ice_base.h and include ice_base.h
where required.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to request an optional device-specific DDP package file
(one with the PCIe Device Serial Number in its name so that different DDP
package files can be used on different devices). If the optional package
file exists, download it to the device. If not, download the default
package file.
Log an appropriate message based on whether or not a DDP package
file exists and the return code from the attempt to download it to the
device. If the download fails and there is not already a package file on
the device, go into "Safe Mode" where some features are not supported.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FW build id is currently being displayed as an int which doesn't make
sense. Instead display FW build id as a hex value. Also add other useful
information to the output such as NVM version, API patch info, and FW
build hash.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver is required to send a version to the firmware
to indicate that the driver is up. If the driver doesn't
do this the firmware doesn't behave properly.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver should start out with a reasonable number of descriptors that
can prevent drops due to a CPU being in a power management state.
Change the default number of descriptors to 2048.
The user can always change the value at runtime. Transmit descriptor
counts are not modified because they don't need to change due to the
speed of the interface, or for power managed CPUs, but the code is
simplified to a fixed value for the transmit default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
