Currently, the vlan_promisc flag is used exclusively by VF VSI to
determine whether or not to toggle VLAN pruning along with
trusted/true-promiscuous mode. This is not needed for a couple of
reasons. First, trusted/true-promiscuous mode is only supposed to allow
all MAC filters within VLANs that a VF has added filters for, so VLAN
pruning should not be disabled. Second, the boolean argument makes the
function confusing and unintuitive. Remove this flag.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some devices have support for loading the PHY FW and in some cases this
can fail. When this fails, the FW will set the corresponding bit in the
link info structure. Also, the FW will send a link event if the correct
link event mask bit is set. Add support for printing an error message
when the PHY FW load fails during any link configuration flow and the
link event flow.
Since ice_check_module_power() is already doing something very similar
add a new function ice_check_link_cfg_err() so any failures reported in
the link info's link_cfg_err member can be printed in this one function.
Also, add the new ICE_FLAG_PHY_FW_LOAD_FAILED bit to the PF's flags so
we don't constantly print this error message during link polling if the
value never changed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add definition for VXLAN and Geneve dummy packet. Define VXLAN and
Geneve type of fields to match on correct UDP tunnel header.
Parse tunnel specific fields from TC tool like outer MACs, outer IPs,
outer destination port and VNI. Save values and masks in outer header
struct and move header pointer to inner to simplify parsing inner
values.
There are two cases for redirect action:
- from uplink to VF - TC filter is added on tunnel device
- from VF to uplink - TC filter is added on PR, for this case check if
redirect device is tunnel device
VXLAN example:
- create tunnel device
ip l add $VXLAN_DEV type vxlan id $VXLAN_VNI dstport $VXLAN_PORT \
dev $PF
- add TC filter (in switchdev mode)
tc filter add dev $VXLAN_DEV protocol ip parent ffff: flower \
enc_dst_ip $VF1_IP enc_key_id $VXLAN_VNI action mirred egress \
redirect dev $VF1_PR
Geneve example:
- create tunnel device
ip l add $GENEVE_DEV type geneve id $GENEVE_VNI dstport $GENEVE_PORT \
remote $GENEVE_IP
- add TC filter (in switchdev mode)
tc filter add dev $GENEVE_DEV protocol ip parent ffff: flower \
enc_key_id $GENEVE_VNI dst_ip $GENEVE1_IP action mirred egress \
redirect dev $VF1_PR
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement indirect notification mechanism to support offloading TC rules
on tunnel devices.
Keep indirect block list in netdev priv. Notification will call setting
tc cls flower function. For now we can offload only ingress type. Return
not supported for other flow block binder.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to add/delete channel specific filter using tc-flower.
For now, only supported action is "skip_sw hw_tc <tc_num>"
Filter criteria is specific to channel and it can be
combination of L3, L3+L4, L2+L4.
Example:
MATCH criteria Action
---------------------------
src and/or dest IPv4[6]/mask -> Forward to "hw_tc <tc_num>"
dest IPv4[6]/mask + dest L4 port -> Forward to "hw_tc <tc_num>"
dest MAC + dest L4 port -> Forward to "hw_tc <tc_num>"
src IPv4[6]/mask + src L4 port -> Forward to "hw_tc <tc_num>"
src MAC + src L4 port -> Forward to "hw_tc <tc_num>"
Adding tc-flower filter for channel using "hw_tc"
-------------------------------------------------
tc qdisc add dev <ethX> clsact
Above two steps are only needed the first time when adding
tc-flower filter.
tc filter add dev <ethX> protocol ip ingress prio 1 flower \
dst_ip 192.168.0.1/32 ip_proto tcp dst_port 5001 \
skip_sw hw_tc 1
tc filter show dev <ethX> ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1 hw_tc 1
eth_type ipv4
ip_proto tcp
dst_ip 192.168.0.1
dst_port 5001
skip_sw
in_hw in_hw_count 1
Delete specific filter:
-------------------------
tc filter del dev <ethx> ingress pref 1 handle 0x1 flower
Delete All filters:
------------------
tc filter del dev <ethX> ingress
Co-developed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support in driver for TC_QDISC_SETUP_MQPRIO. This support
enables instantiation of channels in HW using existing MQPRIO
infrastructure which is extended to be offloadable. This
provides a mechanism to configure dedicated set of queues for
each TC.
Configuring channels using "tc mqprio":
--------------------------------------
tc qdisc add dev <ethX> root mqprio num_tc 3 map 0 1 2 \
queues 4@0 4@4 4@8 hw 1 mode channel
Above command configures 3 TCs having 4 queues each. "hw 1 mode channel"
implies offload of channel configuration to HW. When driver processes
configuration received via "ndo_setup_tc: QDISC_SETUP_MQPRIO", each
TC maps to HW VSI with specified queues.
User can optionally specify bandwidth min and max rate limit per TC
(see example below). If shaper params like min and/or max bandwidth
rate limit are specified, driver configures VSI specific rate limiter
in HW.
Configuring channels and bandwidth shaper parameters using "tc mqprio":
----------------------------------------------------------------
tc qdisc add dev <ethX> root mqprio \
num_tc 4 map 0 1 2 3 queues 4@0 4@4 4@8 4@12 hw 1 mode channel \
shaper bw_rlimit min_rate 1Gbit 2Gbit 3Gbit 4Gbit \
max_rate 4Gbit 5Gbit 6Gbit 7Gbit
Command to view configured TCs:
-----------------------------
tc qdisc show dev <ethX>
Deleting TCs:
------------
tc qdisc del dev <ethX> root mqprio
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As part of support for E810 XXV devices, some device ids were
inadvertently left out. Add those missing ids.
Fixes: 195fb97766 ("ice: add additional E810 device id")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
The driver was having trouble with unreliable latency when doing single
threaded ping-pong tests. This was root caused to the DIM algorithm
landing on a too slow interrupt value, which caused high latency, and it
was especially present when queues were being switched frequently by the
scheduler as happens on default setups today.
In attempting to improve this, we allow the upper rate limit for
interrupts to move to rate limit of 4 microseconds as a max, which means
that no vector can generate more than 250,000 interrupts per second. The
old config was up to 100,000. The driver previously tried to program the
rate limit too frequently and if the receive and transmit side were both
active on the same vector, the INTRL would be set incorrectly, and this
change fixes that issue as a side effect of the redesign.
This driver will operate from now on with a slightly changed DIM table
with more emphasis towards latency sensitivity by having more table
entries with lower latency than with high latency (high being >= 64
microseconds).
The driver also resets the DIM algorithm state with a new stats set when
there is no work done and the data becomes stale (older than 1 second),
for the respective receive or transmit portion of the interrupt.
Add a new helper for setting rate limit, which will be used more
in a followup patch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement ndo_set_vf_rate to support setting of min_tx_rate and
max_tx_rate; set the appropriate bandwidth in the scheduler for the
node representing the specified VF VSI.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Go through the code base and use ice_for_each_* macros. While at it,
introduce ice_for_each_xdp_txq() macro that can be used for looping over
xdp_rings array.
Commit is not introducing any new functionality.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Under rare circumstances there might be a situation where a requirement
of having XDP Tx queue per CPU could not be fulfilled and some of the Tx
resources have to be shared between CPUs. This yields a need for placing
accesses to xdp_ring inside a critical section protected by spinlock.
These accesses happen to be in the hot path, so let's introduce the
static branch that will be triggered from the control plane when driver
could not provide Tx queue dedicated for XDP on each CPU.
Currently, the design that has been picked is to allow any number of XDP
Tx queues that is at least half of a count of CPUs that platform has.
For lower number driver will bail out with a response to user that there
were not enough Tx resources that would allow configuring XDP. The
sharing of rings is signalled via static branch enablement which in turn
indicates that lock for xdp_ring accesses needs to be taken in hot path.
Approach based on static branch has no impact on performance of a
non-fallback path. One thing that is needed to be mentioned is a fact
that the static branch will act as a global driver switch, meaning that
if one PF got out of Tx resources, then other PFs that ice driver is
servicing will suffer. However, given the fact that HW that ice driver
is handling has 1024 Tx queues per each PF, this is currently an
unlikely scenario.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Optimize Tx descriptor cleaning for XDP. Current approach doesn't
really scale and chokes when multiple flows are handled.
Introduce two ring fields, @next_dd and @next_rs that will keep track of
descriptor that should be looked at when the need for cleaning arise and
the descriptor that should have the RS bit set, respectively.
Note that at this point the threshold is a constant (32), but it is
something that we could make configurable.
First thing is to get away from setting RS bit on each descriptor. Let's
do this only once NTU is higher than the currently @next_rs value. In
such case, grab the tx_desc[next_rs], set the RS bit in descriptor and
advance the @next_rs by a 32.
Second thing is to clean the Tx ring only when there are less than 32
free entries. For that case, look up the tx_desc[next_dd] for a DD bit.
This bit is written back by HW to let the driver know that xmit was
successful. It will happen only for those descriptors that had RS bit
set. Clean only 32 descriptors and advance the DD bit.
Actual cleaning routine is moved from ice_napi_poll() down to the
ice_xmit_xdp_ring(). It is safe to do so as XDP ring will not get any
SKBs in there that would rely on interrupts for the cleaning. Nice side
effect is that for rare case of Tx fallback path (that next patch is
going to introduce) we don't have to trigger the SW irq to clean the
ring.
With those two concepts, ring is kept at being almost full, but it is
guaranteed that driver will be able to produce Tx descriptors.
This approach seems to work out well even though the Tx descriptors are
produced in one-by-one manner. Test was conducted with the ice HW
bombarded with packets from HW generator, configured to generate 30
flows.
Xdp2 sample yields the following results:
<snip>
proto 17: 79973066 pkt/s
proto 17: 80018911 pkt/s
proto 17: 80004654 pkt/s
proto 17: 79992395 pkt/s
proto 17: 79975162 pkt/s
proto 17: 79955054 pkt/s
proto 17: 79869168 pkt/s
proto 17: 79823947 pkt/s
proto 17: 79636971 pkt/s
</snip>
As that sample reports the Rx'ed frames, let's look at sar output.
It says that what we Rx'ed we do actually Tx, no noticeable drops.
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 79842324.00 79842310.40 4678261.17 4678260.38 0.00 0.00 0.00 38.32
with tx_busy staying calm.
When compared to a state before:
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 90919711.60 42233822.60 5327326.85 2474638.04 0.00 0.00 0.00 43.64
it can be observed that the amount of txpck/s is almost doubled, meaning
that the performance is improved by around 90%. All of this due to the
drops in the driver, previously the tx_busy stat was bumped at a 7mpps
rate.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With rings being split, it is now convenient to introduce a pointer to
XDP ring within the Rx ring. For XDP_TX workloads this means that
xdp_rings array access will be skipped, which was executed per each
processed frame.
Also, read the XDP prog once per NAPI and if prog is present, set up the
local xdp_ring pointer. Reading prog a single time was discussed in [1]
with some concern raised by Toke around dispatcher handling and having
the need for going through the RCU grace period in the ndo_bpf driver
callback, but ice currently is torning down NAPI instances regardless of
the prog presence on VSI.
Although the pointer to XDP ring introduced to Rx ring makes things a
lot slimmer/simpler, I still feel that single prog read per NAPI
lifetime is beneficial.
Further patch that will introduce the fallback path will also get a
profit from that as xdp_ring pointer will be set during the XDP rings
setup.
[1]: https://lore.kernel.org/bpf/87k0oseo6e.fsf@toke.dk/
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There has been a long lasting issue of improper xdp_rings indexing for
XDP_TX and XDP_REDIRECT actions. Given that currently rx_ring->q_index
is mixed with smp_processor_id(), there could be a situation where Tx
descriptors are produced onto XDP Tx ring, but tail is never bumped -
for example pin a particular queue id to non-matching IRQ line.
Address this problem by ignoring the user ring count setting and always
initialize the xdp_rings array to be of num_possible_cpus() size. Then,
always use the smp_processor_id() as an index to xdp_rings array. This
provides serialization as at given time only a single softirq can run on
a particular CPU.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.
Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.
Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.
Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.
Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.
Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This field is dead and driver is not making any use of it. Simply remove
it.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the remove path, there is an attempt to free the aux_idx IDA whether
it was allocated or not. This can potentially cause a crash when
unloading the driver on systems that do not initialize support for RDMA.
But, this free cannot be gated by the status bit for RDMA, since it is
allocated if the driver detects support for RDMA at probe time, but the
driver can enter into a state where RDMA is not supported after the IDA
has been allocated at probe time and this would lead to a memory leak.
Initialize aux_idx to an invalid value and check for a valid value when
unloading to determine if an IDA free is necessary.
Fixes: d25a0fc41c ("ice: Initialize RDMA support")
Reported-by: Jun Miao <jun.miao@windriver.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement ndo_setup_tc net device callback for TC HW offload on PF device.
ndo_setup_tc provides support for HW offloading various TC filters.
Add support for configuring the following filter with tc-flower:
- default L2 filters (src/dst mac addresses, ethertype, VLAN)
- variations of L3, L3+L4, L2+L3+L4 filters using advanced filters
(including ipv4 and ipv6 addresses).
Allow for adding/removing TC flows when PF device is configured in
eswitch switchdev mode. Two types of actions are supported at the
moment: FLOW_ACTION_DROP and FLOW_ACTION_REDIRECT.
Co-developed-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As resetting all VFs behaves mostly like creating new VFs also
eswitch infrastructure has to be recreated. The easiest way to
do that is to rebuild eswitch after resetting VFs.
Implement helper functions to start and stop all representors
queues. This is used to disable traffic on port representors.
In rebuild path:
- NAPI has to be disabled
- eswitch environment has to be set up
- new port representors have to be created, because the old
one had pointer to not existing VFs
- new control plane VSI ring should be remapped
- NAPI hast to be enabled
- rxdid has to be set to FLEX_NIC_2, because this descriptor id
support source_vsi, which is needed on control plane VSI queues
- port representors queues have to be started
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Only way to enable switchdev is to create VFs when the eswitch
mode is set to switchdev. Check if correct mode is set and
enable switchdev in function which creating VFs.
Disable switchdev when user change number of VFs to 0. Changing
eswitch mode back to legacy when VFs are created in switchdev
mode isn't allowed.
As switchdev takes care of managing filter rules, adding new
rules on VF is blocked.
In case of resetting VF driver has to update pointer in ice_repr
struct, because after reset VSI related things can change.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
New type of VSI has to be defined for switchdev control plane
VSI. Number of allocated Tx and Rx queue has to be equal to
amount of VFs, because each port representor should have one
Tx and Rx queue.
Also to not increase number of used irqs too much, control plane
VSI uses only one q_vector and handle all queues in one irq.
To allow handling all queues in one irq , new function to clean
msix for eswitch was introduced. This function will schedule napi
for each representor instead of scheduling it only for one like in
normal clean irq function.
Only one additional msix has to be requested. Always try to request
it in ice_ena_msix_range function.
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Switchdev environment has to be set up when user create VFs
and eswitch mode is switchdev. Release is done when user
delete all VFs.
Data path in this implementation is based on control plane VSI.
This VSI is used to pass traffic from port representors to
corresponding VFs and vice versa. Default TX rule has to be
added to forward packet to control plane VSI. This will redirect
packets from VFs which don't match other rules to control plane
VSI.
On RX side default rule is added on uplink VSI to receive all
traffic that doesn't match other rules. When setting switchdev
environment all other rules from VFs should be removed. Packet to
VFs will be forwarded by control plane VSI.
As VF without any mac rules can't send any packet because of
antispoof mechanism, VSI antispoof should be turned off on each VFs.
To send packet from representor to correct VSI, destination VSI
field in TX descriptor will have to be filled. Allow that by
setting destination override bit in control plane VSI security config.
Packet from VFs will be received on control plane VSI. Driver
should decide to which netdev forward the packet. Decision is
made based on src_vsi field from descriptor. There is a target
netdev list in control plane VSI struct which choose netdev
based on src_vsi number.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Keeping devlink port inside VSI data structure causes some issues.
Since VF VSI is released during reset that means that we have to
unregister devlink port and register it again every time reset is
triggered. With the new changes in devlink API it
might cause deadlock issues. After calling
devlink_port_register/devlink_port_unregister devlink API is going to
lock rtnl_mutex. It's an issue when VF reset is triggered in netlink
operation context (like setting VF MAC address or VLAN),
because rtnl_lock is already taken by netlink. Another call of
rtnl_lock from devlink API results in dead-lock.
By moving devlink port to PF/VF we avoid creating/destroying it
during reset. Since this patch, devlink ports are created during
ice_probe, destroyed during ice_remove for PF and created during
ice_repr_add, destroyed during ice_repr_rem for VF.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The messaging for unsupported module detection is different for
lenient mode and strict mode. Update the code to print the right
messaging for a given link mode.
Media topology conflict is not an error in lenient mode, so return
an error code only if not in lenient mode.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
DSCP a.k.a L3 QoS is only supported on certain devices. To enforce this,
this patch introduces a bitmap of features and helper functions.
The feature bitmap is set based on device IDs on driver init. Currently,
DSCP is the only feature in this bitmap, but there will be more in the
future. In the DCB netlink flow, check if the feature bit is set before
exercising DSCP.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement code to handle submission of APP TLV's
containing DSCP to TC mapping.
The first such mapping received on an interface
will cause that PF to switch to L3 DSCP QoS mode,
apply the default config for that mode, and apply
the received mapping.
Only one such mapping will be allowed per DSCP value,
and when the last DSCP mapping is deleted, the PF
will switch back into L2 VLAN QoS mode, applying the
appropriate default QoS settings.
L3 DSCP QoS mode will only be allowed in SW DCBx
mode, in other words, when the FW LLDP engine is
disabled. Commands that break this mutual exclusivity
will be blocked.
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move devlink_registration routine to be the last command, when the
device is fully initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF pointer is always valid when PCI core calls its .shutdown() and
.remove() callbacks. There is no need to check it again.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some circumstances, such as with bridging, it's possible that the
stack will add the device's own MAC address to its unicast address list.
If, later, the stack deletes this address, the driver will receive a
request to remove this address.
The driver stores its current MAC address as part of the VSI MAC filter
list instead of separately. So, this causes a problem when the device's
MAC address is deleted unexpectedly, which results in traffic failure in
some cases.
The following configuration steps will reproduce the previously
mentioned problem:
> ip link set eth0 up
> ip link add dev br0 type bridge
> ip link set br0 up
> ip addr flush dev eth0
> ip link set eth0 master br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> modprobe -r veth
> modprobe -r bridge
> ip addr add 192.168.1.100/24 dev eth0
The following ping command fails due to the netdev->dev_addr being
deleted when removing the bridge module.
> ping <link partner>
Fix this by making sure to not delete the netdev->dev_addr during MAC
address sync. After fixing this issue it was noticed that the
netdev_warn() in .set_mac was overly verbose, so make it at
netdev_dbg().
Also, there is a possibility of a race condition between .set_mac and
.set_rx_mode. Fix this by calling netif_addr_lock_bh() and
netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr
is going to be updated in .set_mac.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Liang Li <liali@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The userspace utility "driverctl" can be used to change/override the
system's default driver choices. This is useful in some situations
(buggy driver, old driver missing a device ID, trying a workaround,
etc.) where the user needs to load a different driver.
However, this is also prone to user error, where a driver is mapped
to a device it's not designed to drive. For example, if the ice driver
is mapped to driver iavf devices, the ice driver crashes.
Add a check to return an error if the ice driver is being used to
probe a virtual function.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The E810 device supports programmable pins for enabling both input and
output events related to the PTP hardware clock. This includes both
output signals with programmable period, as well as timestamping of
events on input pins.
Add support for enabling these using the CONFIG_PTP_1588_CLOCK
interface.
This allows programming the software defined pins to take advantage of
the hardware clock features.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch is modeled after one by Scott Peterson for i40e.
Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for DIMLIB to help debug interrupt moderation problems.
Performance should not be affected, and this can be very useful
for debugging and adding new trace events to paths in the future.
Note eBPF programs can attach to these events, as well as perf
can count them since we're attaching to the events subsystem
in the kernel.
Co-developed-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the local variable since it's only used once. Instead, use it
directly.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are some places where the scope of a variable can
be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.
The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.
Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.
To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.
In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.
For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.
Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.
This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.
It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.
Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.
Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.
With this change, E810 devices should be able to perform basic PTP
functionality.
Future changes will extend the support to cover the E822-based devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add SIOCGHWTSTAMP and SIOCSHWTSTAMP ioctl handlers to respond to
requests to enable timestamping support. If the request is for enabling
Rx timestamps, set a bit in the Rx descriptors to indicate that receive
timestamps should be reported.
Hardware captures receive timestamps in the PHY which only captures part
of the timer, and reports only 40 bits into the Rx descriptor. The upper
32 bits represent the contents of GLTSYN_TIME_L at the point of packet
reception, while the lower 8 bits represent the upper 8 bits of
GLTSYN_TIME_0.
The networking and PTP stack expect 64 bit timestamps in nanoseconds. To
support this, implement some logic to extend the timestamps by using the
full PHC time.
If the Rx timestamp was captured prior to the PHC time, then the real
timestamp is
PHC - (lower_32_bits(PHC) - timestamp)
If the Rx timestamp was captured after the PHC time, then the real
timestamp is
PHC + (timestamp - lower_32_bits(PHC))
These calculations are correct as long as neither the PHC timestamp nor
the Rx timestamps are more than 2^32-1 nanseconds old. Further, we can
detect when the Rx timestamp is before or after the PHC as long as the
PHC timestamp is no more than 2^31-1 nanoseconds old.
In that case, we calculate the delta between the lower 32 bits of the
PHC and the Rx timestamp. If it's larger than 2^31-1 then the Rx
timestamp must have been captured in the past. If it's smaller, then the
Rx timestamp must have been captured after PHC time.
Add an ice_ptp_extend_32b_ts function that relies on a cached copy of
the PHC time and implements this algorithm to calculate the proper upper
32bits of the Rx timestamps.
Cache the PHC time periodically in all of the Rx rings. This enables
each Rx ring to simply call the extension function with a recent copy of
the PHC time. By ensuring that the PHC time is kept up to date
periodically, we ensure this algorithm doesn't use stale data and
produce incorrect results.
To cache the time, introduce a kworker and a kwork item to periodically
store the Rx time. It might seem like we should use the .do_aux_work
interface of the PTP clock. This doesn't work because all PFs must cache
this time, but only one PF owns the PTP clock device.
Thus, the ice driver will manage its own kthread instead of relying on
the PTP do_aux_work handler.
With this change, the driver can now report Rx timestamps on all
incoming packets.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.
If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.
Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.
Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice driver requires a programmable pipeline firmware package in order to
have a support for advanced features. Otherwise, driver falls back to so
called 'safe mode'. For that mode, ndo_bpf callback is not exposed and
when user tries to load XDP program, the following happens:
$ sudo ./xdp1 enp179s0f1
libbpf: Kernel error message: Underlying driver does not support XDP in native mode
link set xdp fd failed
which is sort of confusing, as there is a native XDP support, but not in
the current mode. Improve the user experience by providing the specific
ndo_bpf callback dedicated for safe mode which will make use of extack
to explicitly let the user know that the DDP package is missing and
that's the reason that the XDP can't be loaded onto interface currently.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Fixes: efc2214b60 ("ice: Add support for XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After performing a flash update, a device EMP reset may occur. This
reset will cause the newly downloaded firmware to be initialized. When
this happens, the driver still reports the previous NVM version
information.
This is because the NVM versions are cached within the hw structure.
This can be confusing, as the new firmware is in fact running in this
case.
Handle this by calling ice_init_nvm when rebuilding the driver state.
This will update the flash version information and ensures that the
current values are displayed when reporting the NVM versions to the
stack.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Requesting device firmware information while the device is busy cleaning
up after a reset can result in an unexpected failure:
This occurs because the command is attempting to access the device
AdminQ while it is down. Resolve this by having the command wait for
a while until the reset is complete. To do this, introduce
a reset_wait_queue and associated helper function "ice_wait_for_reset".
This helper will use the wait queue to sleep until the driver is done
rebuilding. Use of a wait queue is preferred because the potential sleep
duration can be several seconds.
To ensure that the thread wakes up properly, a new wake_up call is added
during all code paths which clear the reset state bits associated with
the driver rebuild flow.
Using this ensures that tools can request device information without
worrying about whether the driver is cleaning up from a reset.
Specifically, it is expected that a flash update could result in
a device reset, and it is better to delay the response for information
until the reset is complete rather than exit with an immediate failure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Register ice client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the auxiliary driver (irdma) to attach to.
It allows to realize a single RDMA driver (irdma) capable of working with
multiple netdev drivers over multi-generation Intel HW supporting RDMA.
There is no load ordering dependencies between ice and irdma.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Checkpatch reports the following, fix it.
-----------------------------------------
drivers/net/ethernet/intel/ice/ice_main.c
-----------------------------------------
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
FILE: drivers/net/ethernet/intel/ice/ice_main.c:455:
+
+}
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Currently the driver is doing two unnecessary checks. First both ops are
checking if the VLAN ID passed in is less than VLAN_N_VID and second
both ops are checking to see if a port VLAN is configured on the VSI.
The first check is already handled by the 8021q driver so this is an
unnecessary check. The second check is unnecessary because the PF VSI is
never put into a port VLAN.
Remove these checks.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tracking of the rx_gro_dropped statistic was removed in
commit f73fc40327 ("ice: drop dead code in ice_receive_skb()").
Remove the associated variables and its reporting to ethtool stats.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace multiple instances of vsi->back and pi->phy with equivalent
local variables
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_init_phy_user_cfg, vsi is used only to get to hw. Remove this
and just use pi->hw
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When link is owned by manageability, the driver is not allowed to fiddle
with link. FW returns ICE_AQ_RC_EMODE if the driver attempts to do so.
This patch adds a new function ice_set_link which abstracts the call to
ice_aq_set_link_restart_an and provides a clean way to turn on/off link.
While making this change, I also spotted that an int variable was being
used to hold both an ice_status return code and the Linux errno return
code. This pattern more often than not results in the driver inadvertently
returning ice_status back to kernel which is a major boo-boo. Clean it up.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.
enum ice_state is used to represent state information of the PF.
While some of these enum values can be use to represent VSI state,
it makes more sense to represent VSI state with its own enum. So
derive a new enum ice_vsi_state from ice_vsi_flags and ice_state
and use it. Also rename enum ice_state to ice_pf_state for clarity.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently ice_set/get_rss are used to set/get the RSS LUT and/or RSS
key. However nearly everywhere these functions are called only the LUT
or key are set/get. Also, making this change reduces how many things
ice_set/get_rss are doing. Fix this by adding ice_set/get_rss_lut and
ice_set/get_rss_key functions.
Also, consolidate all calls for setting/getting the RSS LUT and RSS Key
to use ice_set/get_rss_lut() and ice_set/get_rss_key().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update ice_aq_get_rss_lut() and ice_aq_set_rss_lut() to take a new
structure ice_aq_get_set_rss_params instead of passing individual
parameters. This is done for 2 reasons:
1. Reduce the number of parameters passed to the functions.
2. Reduce the amount of change required if the arguments ever need to be
updated in the future.
Also, reduce duplicate code that was checking for an invalid vsi_handle
and lut parameter by moving the checks to the lower level
__ice_aq_get_set_rss_lut().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Change link misconfiguration message since the configuration
could be intended by the user.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Once a netdev is registered, the corresponding network interface can
be immediately used by userspace utilities (like say NetworkManager).
This can be problematic if the driver technically isn't fully up yet.
Move netdev registration to the end of probe, as by this time the
driver data structures and device will be initialized as expected.
However, delaying netdev registration causes a failure in the aRFS flow
where netdev->reg_state == NETREG_REGISTERED condition is checked. It's
not clear why this check was added to begin with, so remove it.
Local testing didn't indicate any issues with this change.
The state bit check in ice_open was put in as a stop-gap measure to
prevent a premature interface up operation. This is no longer needed,
so remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As per the spec, the WoL control word read from the NVM should be
interpreted as port numbers, and not PF numbers. So when checking
if WoL supported, use the port number instead of the PF ID.
Also, ice_is_wol_supported doesn't really need a pointer to the pf
struct, but just needs a pointer to the hw instance.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a possibility of race between ice_open or ice_stop calls
performed by OS and reset handling routine both trying to modify VSI
resources. Observed scenarios:
- reset handler deallocates memory in ice_vsi_free_arrays and ice_open
tries to access it in ice_vsi_cfg_txq leading to driver crash
- reset handler deallocates memory in ice_vsi_free_arrays and ice_close
tries to access it in ice_down leading to driver crash
- reset handler clears port scheduler topology and sets port state to
ICE_SCHED_PORT_STATE_INIT leading to ice_ena_vsi_txq fail in ice_open
To prevent this additional checks in ice_open and ice_stop are
introduced to make sure that OS is not allowed to alter VSI config while
reset is in progress.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Krzysztof Goreczny <krzysztof.goreczny@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
An incorrect NVM update procedure can result in the driver failing probe.
In this case, the recommended resolution method is to update the NVM
using the right procedure. However, if the driver fails probe, the user
will not be able to update the NVM. So do not fail probe on link/PHY
errors.
Fixes: 1a3571b593 ("ice: restore PHY settings on media insertion")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct reported warnings for "warning: expecting prototype for ...
Prototype was for ... instead"
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.
To enable returning FDIR completion status from ctrl_vsi Rx queue,
COMP_Queue and COMP_Report of FDIR filter programming descriptor
needs to be properly configured. After program request sent to ctrl_vsi
Tx queue, ctrl_vsi Rx queue interrupt will be triggered and
completion status will be returned.
Driver will first issue request in ice_vc_fdir_add_fltr(), then
pass FDIR context to the background task in interrupt service routine
ice_vc_fdir_irq_handler() and finally deal with them in
ice_flush_fdir_ctx(). ice_flush_fdir_ctx() will check the descriptor's
value, fdir context, and then send back virtual channel message to VF
by calling ice_vc_add_fdir_fltr_post(). An additional timer will be
setup in case of hardware interrupt timeout.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are going to enable FDIR configure for AVF through virtual channel.
The first step is to add helper functions to support control VSI setup.
A control VSI will be allocated for a VF when AVF creates its
first FDIR rule through ice_vf_ctrl_vsi_setup().
The patch will also allocate FDIR rule space for VF's control VSI.
If a VF asks for flow director rules, then those should come entirely
from the best effort pool and not from the guaranteed pool. The patch
allow a VF VSI to have only space in the best effort rules.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
dev_validate_mtu checks that mtu value specified by user is not less
than min mtu and not greater than max allowed mtu. It is being done
before calling the ndo_change_mtu exposed by driver, so remove these
redundant checks in ice_change_mtu.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently if the driver is unable to get all the MSI-X vectors it wants, it
falls back to the minimum configuration which equates to a single Tx/Rx
traffic queue pair. Instead of using the minimum configuration, if given
more vectors than the minimum, utilize those vectors for additional traffic
queues after accounting for other interrupts.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
This message indicates an error on close, not open.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create set scheduler aggregator node and move for VSIs into respective
scheduler node. Max children per aggregator node is 64.
There are two types of aggregator node(s) created.
1. dedicated node for PF and _CTRL VSIs
2. dedicated node(s) for VFs.
As part of reset and rebuild, aggregator nodes are recreated and VSIs
are moved to respective aggregator node.
Having related VSIs in respective tree avoid starvation between PF and VF
w.r.t Tx bandwidth.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Co-developed-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Victor Raj <victor.raj@intel.com>
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the framework and initial implementation for receiving and processing
netdev bonding events. This is only the software support and the
implementation of the HW offload for bonding support will be coming at a
later time. There are some architectural gaps that need to be closed
before that happens.
Because this is a software only solution that supports in kernel bonding,
SR-IOV is not supported with this implementation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current implementation of netdev already contains xsk_buff_pools.
We no longer have to contain these structures in ice_vsi.
Refactor the code to operate on netdev-provided xsk_buff_pools.
Move scheduling napi on each queue to a separate function to
simplify setup function.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The check for a NULL pf pointer is moot since the earlier declaration and
assignment of struct device *dev already de-referenced the pointer. Also,
the only caller of ice_set_dflt_mib() already ensures pf is not NULL.
Cc: Dave Ertman <david.m.ertman@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in
struct ice_res_tracker, instead of a one-element array and use the
struct_size() helper to calculate the size for the allocations.
Also, notice that the code below suggests that, currently, two too many
bytes are being allocated with devm_kzalloc(), as the total number of
entries (pf->irq_tracker->num_entries) for pf->irq_tracker->list[] is
_vectors_ and sizeof(*pf->irq_tracker) also includes the size of the
one-element array _list_ in struct ice_res_tracker.
drivers/net/ethernet/intel/ice/ice_main.c:3511:
3511 /* populate SW interrupts pool with number of OS granted IRQs. */
3512 pf->num_avail_sw_msix = (u16)vectors;
3513 pf->irq_tracker->num_entries = (u16)vectors;
3514 pf->irq_tracker->end = pf->irq_tracker->num_entries;
With this change, the right amount of dynamic memory is now allocated
because, contrary to one-element arrays which occupy at least as much
space as a single object of the type, flexible-array members don't
occupy such space in the containing structure.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9-rc1/process/deprecated.html#zero-length-and-one-element-arrays
Built-tested-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the driver to copy the MAC address configured in ndo_set_mac_address
into dev_addr, even if the MAC filter already exists in HW. In some
situations (e.g. bonding) the netdev's dev_addr could have been modified
outside of the driver, with no change to the HW filter, so the driver
cannot assume that they match.
Fixes: 757976ab16 ("ice: Fix check for removing/adding mac filters")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
All UDP tunnel port management is now routed via udp_tunnel_nic
infra directly. Remove the old callbacks.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add space to the end of 'Unknown' string in order to avoid
concatenation with 'bps' string when formatting netdev log message.
Signed-off-by: Simon Perron Caissy <simon.perron.caissy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
vlan_ena was introduced to track whether VLAN filters are enabled on
the device, but
1) checking for num_vlan > 1 already gives us this information, and is
currently used in this way throughout the code
2) the logic for vlan_ena is broken when multiple VLANs are active
Just remove vlan_ena and use num_vlan instead.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.
Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.
In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.
If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.
This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.
Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.
Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.
Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the checks cover only parts of the contexts in which these
functions cannot be called. They fail to detect preemption or interrupt
disabled invocations.
As the functions which are invoked from the various places contain already
a broad variety of checks (always enabled or debug option dependent) cover
all invalid conditions already, there is no point in having inconsistent
warnings in those drivers.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ice to the new infra, use share port tables.
Leave a tiny bit more error checking in place than usual,
because this driver really does quite a bit of magic.
We need to calculate the number of VxLAN and GENEVE entries
the firmware has reserved.
Thanks to the conversion the driver will no longer sleep in
an atomic section.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ice_setup_pf_sw function can cause a memory leak if register_netdev
fails, due to accidentally failing to free the VSI rings. Fix the memory
leak by using ice_vsi_release, ensuring we actually go through the full
teardown process.
This should be safe even if the netdevice is not registered because we
will have set the netdev pointer to NULL, ensuring ice_vsi_release won't
call unregister_netdev.
An alternative fix would be moving management of the PF VSI netdev into
the main VSI setup code. This is complicated and likely requires
significant refactor in how we manage VSIs
Fixes: 3a858ba392 ("ice: Add support for VSI allocation and deallocation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It appears that the ice_suspend flow is missing a call to pci_save_state
and this is triggering the message "State of device not saved by
ice_suspend" and a call trace. Fix it.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable VLAN pruning when entering promiscuous mode, and re-enable it
when exiting.
Without this VLAN-over-bridge topologies created on the device won't be
functional unless rx-vlan-filter is explicitly disabled with ethtool.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Display and count some useful hot-path statistics. The usefulness is as
follows:
- tx_restart: use to determine if the transmit ring size is too small or
if the transmit interrupt rate is too low.
- rx_gro_dropped: use to count drops from GRO layer, which previously were
completely uncounted when occurring.
- tx_busy: use to determine when the driver is miscounting number of
descriptors needed for an skb.
- tx_timeout: as our other drivers, count the number of times we've reset
due to timeout because the kernel only prints a warning once per netdev.
Several of these were already counted but not displayed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In certain configurations without power management support, the
following warnings happen:
drivers/net/ethernet/intel/ice/ice_main.c:4214:12: warning:
'ice_resume' defined but not used [-Wunused-function]
4214 | static int ice_resume(struct device *dev)
| ^~~~~~~~~~
drivers/net/ethernet/intel/ice/ice_main.c:4150:12: warning:
'ice_suspend' defined but not used [-Wunused-function]
4150 | static int ice_suspend(struct device *dev)
| ^~~~~~~~~~~
Mark these functions as __maybe_unused to make it clear to the
compiler that this is going to happen based on the configuration,
which is the standard for these types of functions.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As part of ice_setup_pf_sw() a PF VSI is setup; release the VSI in case of
failure.
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the PF VSI's context parameters are left in a bad state when
going into safe mode. This is causing VLAN traffic to not pass. Fix this
by configuring the PF VSI to allow all VLAN tagged traffic.
Also, remove redundant comment explaining the safe mode flow in
ice_probe().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the driver experiences a link event (especially link up)
there can be multiple events generated. Some of these are
link fault and still have a state of DOWN set. The problem
happens when the link comes UP during the PF driver handling
one of the LINK DOWN events. The status of the link is updated
and is now seen as UP, so when the actual LINK UP event comes,
the port information has already been updated to be seen as UP,
even though none of the UP activities have been completed.
After the link information has been updated in the link
handler and evaluated for MEDIA PRESENT, if the state
of the link has been changed to UP, treat the DOWN event
as an UP event since the link is now UP.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After a GLOBR, the link was broken so that a link
up situation was being seen as a link down.
The problem was that the rebuild process was updating
the port_info link status without doing any of the
other things that need to be done when link changes.
This was causing the port_info struct to have current
"UP" information so that any further UP interrupts
were skipped as redundant.
The rebuild flow should *not* be updating the port_info
struct link information, so eliminate this and leave
it to the link event handling code.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a bug where the LFC settings are not being preserved
through a link event. The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.
On a link-up event, make sure that a set_local_mib is being
performed.
Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The method struct pci_error_handlers.error_detected() is defined and
documented as taking an 'enum pci_channel_state' for the second argument,
but most drivers use 'pci_channel_state_t' instead.
This 'pci_channel_state_t' is not a typedef for the enum but a typedef for
a bitwise type in order to have better/stricter typechecking.
Consolidate everything by using 'pci_channel_state_t' in the method's
definition, in the related helpers and in the drivers.
Enforce use of 'pci_channel_state_t' by replacing 'enum pci_channel_state'
with an anonymous 'enum'.
Note: Currently, from a typechecking point of view this patch changes
nothing because only the constants defined by the enum are bitwise, not the
enum itself (sparse doesn't have the notion of 'bitwise enum'). This may
change in some not too far future, hence the patch.
[bhelgaas: squash in
https://lore.kernel.org/r/20200702162651.49526-3-luc.vanoostenryck@gmail.comhttps://lore.kernel.org/r/20200702162651.49526-4-luc.vanoostenryck@gmail.com]
Link: https://lore.kernel.org/r/20200702162651.49526-2-luc.vanoostenryck@gmail.com
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2020-06-25
This series contains updates to i40e driver and removes the individual
driver versions from all of the Intel wired LAN drivers.
Shiraz moves the client header so that it can easily be shared between
the i40e LAN driver and i40iw RDMA driver.
Jesse cleans up the unused defines, since they are just dead weight.
Alek reduces the unreasonably long wait time for a PF reset after reboot
by using jiffies to limit the maximum wait time for the PF reset to
succeed. Added additional logging to let the user know when the driver
transitions into recovery mode. Adds new device support for our 5 Gbps
NICs.
Todd adds a check to see if MFS is set after warm reboot and notifies
the user when MFS is set to anything lower than the default value.
Arkadiusz fixes a possible race condition, where were holding a
spin-lock while in atomic context.
v2: removed code comments that were no longer applicable in patch 2 of
the series. Also removed 'inline' from patch 4 and patch 8 of the
series. Also re-arranged code to be able to remove the forward
function declarations. Dropped patch 9 of the series, while the
author works on cleaning up the commit message.
v3: Updated patch 8 description to answer Jakub's questions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
The READ_ONCE macro is used when reading rings prior to accessing the
statistics pointer. The corresponding WRITE_ONCE usage when allocating and
freeing the rings to ensure protected access was not in place. Introduce
this.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ceb2f00707 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.
Fixes: ceb2f00707 ("ice: Use pci_get_dsn()")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently VF VSI are being reset twice during a PFR or greater. This is
causing reset, specifically resetting all VFs, to take too long. This is
causing various issues with VF drivers not being able to gracefully
handle the VF reset timeout. Fix this by refactoring how VF reset is
handled for the case mentioned previously and for the VFR/VFLR case.
The refactor was done by doing the following:
1. Removing the call to ice_vsi_rebuild_by_type for
ICE_VSI_VF VSI, which was causing the initial VSI rebuild.
2. Adding functions for pre/post VSI rebuild functions that can be called
in both the reset all VFs case and reset individual VF case.
3. Adding VSI rebuild functions that are specific for the reset all VFs
case and adding functions that are specific for the reset individual
VF case.
4. Calling the pre-rebuild function, then the specific VSI rebuild
function based on the reset type, and then calling the post-rebuild
function to handle VF resets.
This patch series makes some assumptions about how VSI are handling by
FW during reset:
1. During a PFR or greater all VSI in FW will be cleared.
2. During a VFR/VFLR the VSI rebuild responsibility is in the hands of
the PF software.
3. There is code in the ice_reset_all_vfs() case to amortize operations
if possible. This was left intact.
4. PF software should not be replaying VSI based filters that were added
other than host configured, PF software configured, or the VF's
default/LAA MAC. This is the VF drivers job after it has been reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If register_netdev() fails, the driver will attempt to cleanup the
q_vectors and inadvertently trigger a kernel BUG due to a NULL pointer
dereference.
This occurs because cleaning up q_vectors attempts to call
netif_napi_del on napi_structs which were never initialized.
Resolve this by releasing the netdev in ice_cfg_netdev and setting
vsi->netdev to NULL. This ensures that after ice_cfg_netdev fails the
state is rewound to match as if ice_cfg_netdev was never called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are certain cases where the DDP load fails and the FW issues a
core reset. For these cases, wait for reset to complete before
proceeding with reset of the driver init.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In current implementation number of XDP Tx queues is the same as
the number of transmit queues, which is not always true. This
patch changes this number to match the number of receive queues.
XDP programs are running on Rx rings, so what we actually need to
provide is the XDP Tx ring per each Rx ring so that the whole XDP
ecosystem is functional, e.g. if the result of XDP prog is XDP_TX
then you have the need to access the XDP Tx ring.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx program is loaded and packets are sent from
interface, VSI statistics are not updated. This patch adds
packets sent on Tx XDP ring to VSI ring stats.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx rings are destroyed the number of XDP Tx queues
is not changing. This patch is changing this number to 0.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A race condition between FW and SW can occur between admin queue setup and
the first command sent. A link event may occur and FW attempts to notify a
non-existent queue. FW will set the critical error bit and disable the
queue. When this happens retry queue setup.
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are only including illegal_bytes and rx_crc_errors in the
PF netdev's rx_error counter. There are many more causes of Rx errors
that the device supports and reports via Ethtool. Accumulate all Rx
errors in the PF netdev's rx_error counter.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the remaining signed vs unsigned issues, which appear
when compiling with -Werror=sign-compare.
Many of these are because there is an external interface that is passing
an int to us (which we can't change) but that we (rightfully) store
and compare against as an unsigned in our data structures.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix loop variables that are comparing or assigning signed against
unsigned values, mostly by declaring loop counters as unsigned.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was using rq_last_status where it should have been
using sq_last_status. Fix the string to be using the correct
error reporting variable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Require the Dynamic Device Personalization (DDP) file to have the same
major version number and the same or older minor number than the firmware
version major and minor, respectively.
Check the OS and NVM package versions before downloading the package.
If the OS package version is not compatible with NVM then return an
appropriate error.
Split the 32-byte segment name into a 28-byte segment name and
a 4-byte Track-ID. Older packages will still work with this change
because no package has a name that will take up more than 28 bytes;
in this case the Track-ID will be 0.
Note that the driver will store the segment name as 32-bytes in the
ice_hw structure, in order to normalize the length of the various
package name strings that it uses.
Also add section ID and structure for the segment metadata section.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rx MDD auto reset message was not being logged because logging occurred
after the VF reset and the VF MDD data was reinitialized.
Log the Rx MDD auto reset message before triggering the VF reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the specification, the driver needs to call set_mac_cfg
(opcode 0x0603) to be able to exercise jumbo frames. Call the
function during initialization and the post reset rebuild flow.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable accelerated Receive Flow Steering (aRFS). It is used to steer Rx
flows to a specific queue. This functionality is triggered by the network
stack through ndo_rx_flow_steer and requires Flow Director (ntuple on) to
function.
The fltr_info is used to add/remove/update flow rules in the HW, the
fltr_state is used to determine what to do with the filter with respect
to HW and/or SW, and the flow_id is used in co-ordination with the
network stack.
The work for aRFS is split into two paths: the ndo_rx_flow_steer
operation and the ice_service_task. The former is where the kernel hands
us an Rx SKB among other items to setup aRFS and the latter is where
the driver adds/updates/removes filter rules from HW and updates filter
state.
In the Rx path the following things can happen:
1. New aRFS entries are added to the hash table and the state is
set to ICE_ARFS_INACTIVE so the filter can be updated in HW
by the ice_service_task path.
2. aRFS entries have their Rx Queue updated if we receive a
pre-existing flow_id and the filter state is ICE_ARFS_ACTIVE.
The state is set to ICE_ARFS_INACTIVE so the filter can be
updated in HW by the ice_service_task path.
3. aRFS entries marked as ICE_ARFS_TODEL are deleted
In the ice_service_task path the following things can happen:
1. New aRFS entries marked as ICE_ARFS_INACTIVE are added or
updated in HW.
and their state is updated to ICE_ARFS_ACTIVE.
2. aRFS entries are deleted from HW and their state is updated
to ICE_ARFS_TODEL.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a reset, Flow Director filters are cleared from the hardware.
Rebuild the filters using the software structures containing the filter
rules.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functionality for ethtool --show-ntuple, allowing for filters to be
displayed when set functionality is added. Add statistics related to
Flow Director matches and status.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.
Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable status cannot be zero due to a prior check of it; remove this
check.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The else conditional expression is always true due to the if conditional
expression; remove it and add a comment to make it obvious still.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In function ice_set_mac_address, we will remove old dev_addr before
adding the new MAC. In the removing and adding process of the MAC,
there is no need to return error if the check finds the to-be-removed
dev_addr does not exist in the MAC filter list or the to-be-added mac
already exists, keep going or return success accordingly.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move filter functions to separate file.
Add functions that prepare suitable ice_fltr_info struct
depending on the filter type and add this struct to earlier created
list:
- ice_fltr_add_mac_to_list
- ice_fltr_add_vlan_to_list
- ice_fltr_add_eth_to_list
This functions are used in adding and removing filters.
Create wrappers for functions mentioned above that alloc list,
add suitable ice_fltr_info to it and call add or remove function.
- ice_fltr_prepare_mac
- ice_fltr_prepare_mac_and_broadcast
- ice_fltr_prepare_vlan
- ice_fltr_prepare_eth
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.
In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.
There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.
Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When printing the ice status or AQ error codes, instead of printing out the
numerical value, provide the description of the error code. This provides
more info about the issue than a number.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As soon as the driver registers the PF netdev, userspace utilities
like NetworkManager try to bring up the associated interface. When
this happens, the driver may not have finished initializing fully,
resulting in a bunch of errors in the interface up flow.
The driver already has a mechanism to indicate if it's not up yet;
by setting the __ICE_DOWN bit in pf->state, but this bit gets
cleared too early in the current flow. So clear this bit only when
the driver is fully up. Also check for the same bit in the ice_open
flow, and return -EBUSY if the bit is set.
Also in ice_open, replace references of vsi->back with a local
variable.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there's a Tx timeout for a queue which belongs to a PFC enabled TC,
then it's not because the queue is hung but because PFC is in action.
In PFC, peer sends a pause frame for a specified period of time when its
buffer threshold is exceeded (due to congestion). Netdev on the other
hand checks if ACK is received within a specified time for a TX packet, if
not, it'll invoke the tx_timeout routine.
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a boost TCAM entry for each tunnel port in order to get a tunnel
PTYPE. Update netdev feature flags and implement the appropriate logic to
get and set values for hardware offloads.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAl6GTQMUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vy3PhAAmqpYBRobOsG8QbmKDjoJEFtkqdvD
z6+4zf/R+hF11RyXjMDwihIe8d+tkQ4eAaYu6Oh5PrTyanz0G0PgeCrivZeytULk
thqQIWzDQMVA5vN/2/Vy8s5s+3HzP8z/MZOFScJ7+xA1MndXptPRTNmFUbjx+GAv
x8/pTp0u9AF6m7itX65DxXvwkzjWamt+Ar4Yx2IcuKAU/M5RtfuZO3PpDnqn7/wk
JFlkRoYeFB6qNnnkPdeyPHl9dALhuhzgdTyklQEnKVW3nf3xThYDhcEwdh6kBQgl
0dH8lL5LXy7PKGN8RES4wB0Vqndw/HlsCF5O4wkkfItbnbJxGJtS139e5973m0ud
sgWvF4yJAT2jCKhIeNz34sePQJMyWALhv0XzZCsJ0YeGHsrV1jrHELkwUT1+eIsT
3UV0iZ6aL06zQJDyKUbbIcQzEQ/wwBC+x9VgsyL54K1quCQZ1N1Nl/dvrb4cRG9m
m9EhJK/brDf4c0uFlOmMTSxV1t5J+z6ZSQnh1ShD/o5yBsxqN6q5brDT6LEs+jbM
LsIkA18jJOd4OyiDs98YiFKvIfFQbQ0LEBQpJwhF0snvfBFMMbUYN/T/NYneWON/
F0TpkFoP7PXDuq55iNaLdnObfzrpC9kdzUyWvePUvjxIl55bkf+/qtUny+H48t4L
dNggvW052d7BHes=
=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a devlink region for exposing the device's Non Volatime Memory flash
contents.
Support the recently added .snapshot operation, enabling userspace to
request a snapshot of the NVM contents via DEVLINK_CMD_REGION_NEW.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Begin implementing support for the devlink interface with the ice
driver.
The pf structure is currently memory managed through devres, via
a devm_alloc. To mimic this behavior, after allocating the devlink
pointer, use devm_add_action to add a teardown action for releasing the
devlink memory on exit.
The ice hardware is a multi-function PCIe device. Thus, each physical
function will get its own devlink instance. This means that each
function will be treated independently, with its own parameters and
configuration. This is done because the ice driver loads a separate
instance for each function.
Due to this, the implementation does not enable devlink to manage
device-wide resources or configuration, as each physical function will
be treated independently. This is done for simplicity, as managing
a devlink instance across multiple driver instances would significantly
increase the complexity for minimal gain.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ed5a3f664c ("ice: Removing hung_queue variable to use txqueue
function parameter") began utilizing the txqueue variable over the
hung_queue variable. hung_queue was an int where txqueue is an unsigned
int. Update the format specifiers to reflect the new type.
Fixes: ed5a3f664c ("ice: Removing hung_queue variable to use txqueue function parameter")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF's mailbox receive queue is only 512 entries. This fine,
but considering that all VF's mailbox send queues funnel into the PF's
single mailbox receive queue, let's increase it to the maximum size. This
will help prevent any possible bottleneck/slowdown occurring from the PF's
mailbox receive queue being full.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, if there are bare-metal VFs passing traffic and the ice
driver is removed, there is a possibility of VFs triggering a Tx timeout
right before iavf_remove(). This is causing iavf_close() to not be
called because there is a check in the beginning of iavf_remove() that
bails out early if (adapter->state < IAVF_DOWN_PENDING). This makes it
so some resources do not get cleaned up. Specifically, free_irq()
is never called for data interrupts, which results in the following line
of code to trigger:
pci_disable_msix()
free_msi_irqs()
...
BUG_ON(irq_has_action(entry->irq + i));
...
To prevent the Tx timeout from occurring on the VF during driver unload
for ice and the iavf there are a few changes that are needed.
[1] Don't disable all active VF Tx/Rx queues prior to calling
pci_disable_sriov.
[2] Call ice_free_vfs() before disabling the service task.
[3] Disable VF resets when the ice driver is being unloaded by setting
the pf->state flag __ICE_VF_RESETS_DISABLED.
Changing [1] and [2] allow each VF driver's remove flow to successfully
send VIRTCHNL requests, which includes queue disable. This prevents
unexpected Tx timeouts because the PF driver is no longer forcefully
disabling queues.
Due to [1] and [2] there is a possibility that the PF driver will get a
VFLR or reset request over VIRTCHNL from a VF during PF driver unload.
Prevent that by doing [3].
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the open-coded implementation for reading the PCIe DSN with
pci_get_dsn().
The pci_get_dsn() function will perform two pci_read_config_dword calls
to read the lower and upper config dwords. It bitwise ORs them into
a u64 value. Instead of using put_unaligned_le32 to convert the value to
LE32 format, just use the %016llX printf specifier. This will print the
u64 correct, putting the most significant byte of the value first. Since
pci_get_dsn() correctly orders the two dwords into a u64, this should
produce equivalent results in less code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This product's name has changed; update the macro identifier accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add E823 device ids and convert conditional expressions to a more
appropriate switch statement.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for device id 0x159b.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were several strings found without line feeds, fix
them by adding a line feed, as is typical. Without this
lotsofmessagescanbejumbledtogether.
This patch has known checkpatch warnings from long lines
for the NL_* messages, because checkpatch doesn't know
how to ignore them.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the PF VFs MDD event message to rate limit once per second and
report the total number Rx|Tx event count. Add support to print pending
MDD events that occur during the rate limit. The use of net_ratelimit did
not allow for per VF Rx|Tx granularity.
Additional PF MDD log messages are guarded by netif_msg_[rx|tx]_err().
Since VF RX MDD events disable the queue, add ethtool private flag
mdd-auto-reset-vf to configure VF reset to re-enable the queue.
Disable anti-spoof detection interrupt to prevent spurious events
during a function reset.
To avoid race condition do not make PF MDD register reads conditional
on global MDD result.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 0290bd291c ("netdev: pass the stuck queue to the timeout handler")
introduced a new argument to the function but missed adding the description
of the argument to the function header comment. Add it now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"fallthrough" comments are used in switch case statements to explicitly
indicate the code is intended to fall through to the following statement.
Different variants of "fallthough" are acceptable, e.g. "fall through",
"fallthrough", "Fall-through". The GCC compiler has an optional warning
(-Wimplicit-fallthrough[=n]) to warn when such a comment is not present;
the default version of which is enabled when compiling the Linux kernel.
There have been recent discussions in kernel mailing lists regarding
replacing non-standardized "fallthrough" comments with the pseudo-reserved
word 'fallthrough' which will be defined as __attribute__ ((fallthrough))
for versions of gcc that support it (i.e. gcc 7 and newer) or as a nop
for versions that do not. Replace "fallthrough" comments with fallthrough
reserved word.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fallthrough comments are used to explicitly indicate the code is intended
to flow from one case statement to the next in a switch statement rather
than break out of the switch statement. They are only needed when a case
has one or more statements to execute before falling through to the next
case, not when there is a list of cases for which the same statement(s)
should be executed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are not handling LAN overflow events. There can be cases
where LAN overflow events occur on VF queues, especially with Link Flow
Control (LFC) enabled on the controlling PF. In order to recover from
the LAN overflow event caused by a VF we need to determine if the queue
belongs to a VF and reset that VF accordingly.
The struct ice_aqc_event_lan_overflow returns a copy of the GLDCB_RTCTQ
register, which tells us what the queue index is in the global/device
space. The global queue index needs to first be converted to a PF space
queue index and then it can be used to find if a VF owns it.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when we enable/disable all Rx queues we do the following
sequence for each Rx queue and then move to the next queue.
1. Enable/Disable the Rx queue via register write.
2. Read the configuration register to determine if the Rx queue was
enabled/disabled successfully.
In some cases enabling/disabling queue 0 fails because of step 2 above.
Fix this by doing step 1 for all of the Rx queues and then step 2 for
all of the Rx queues.
Also, there are cases where we enable/disable a single queue (i.e.
SR-IOV and XDP) so add a new function that does step 1 and 2 above with
a read flush in between.
This change also required a single Rx queue to be enabled/disabled with
and without waiting for the change to propagate through hardware. Fix
this by adding a boolean wait flag to the necessary functions.
Also, add the keywords "one" and "all" to distinguish between
enabling/disabling a single Rx queue and all Rx queues respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow support for S-Tag + C-Tag VLAN traffic by disabling pruning when
there are no 0x8100 VLAN interfaces currently created on top of the PF.
When an 0x8100 VLAN interface is configured, enable pruning and only
support single and double C-Tag VLAN traffic. If all of the 0x8100
interfaces that were created on top of the PF are removed via
ethtool -K <iface> rx-vlan-filter off or via ip tools, then disable
pruning and allow S-Tag + C-Tag traffic again.
Add VLAN 0 filter by default for the PF. This is because a bridge
sets the default_pvid to 1, sends the request down to
ice_vlan_rx_add_vid(), and we never get the request to add VLAN 0 via
the 8021q module which causes all untagged traffic to be dropped.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the correct netif_msg_[tx,rx]_error() function to determine whether to
print the MDD event type.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Formatting strings in print function calls (like dev_info, dev_err, etc.)
can exceed 80 columns without making checkpatch unhappy. So remove
newlines where applicable and make print statements more compact.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool. Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe. This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies link message logging to include "Full Duplex" and
"Negotiated" for FEC, so as to distinguish it from "Requested" FEC.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None
of the data structures accessed within the block are wrapped with
this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported
will be 0 anyway.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ice_dcb_rebuild had some logic
flaws in it, and also didn't differentiate
between FW and SW modes needs.
For FW flow, the willing setting was being
forced to OFF and left that way. Unwilling
in DCB FW mode is not a supported model.
Leave the config alone and use the return value
from the set command to determine if setting the
config was successful.
The SW DCB flow does not need to need to register
for MIB change events (as they are not used in
SW mode).
Use !is_sw_lldp checks to only perform FW specific
task while in FW mode.
Also adding a reapplication of the current DCB
config after a link event. Some NVMs are not
maintaining their DCB configs across link events.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version to 0.8.2-k
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The scope of function .ndo_tx_timeout was changed to include the hang
queue when a TX timeout event occurs. See commit 0290bd291c
("netdev: pass the stuck queue to the timeout handler") for more
details. Now, drivers don't need to identify which queue is stopped.
Drivers can simply use the queue index provided by dev_watchdog and
execute all actions needed to restore network traffic. This commit do
some cleanups into Intel ice driver to remove a redundant loop to find
stopped queue.
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for E822 devices
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following the changes of commit 12299132b3 ("net: ethernet: intel: Demote
MTU change prints to debug"), change the MTU change message to netdev_dbg()
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the flow for ice_set_vf_link_state() is not configuring link
the same as all other VF link configuration flows. Fix this by only
setting the necessary VF members in ice_set_vf_link_state() and then
call ice_vc_notify_link_state() to actually configure link for the
VF. This made ice_set_pfe_link_forced() unnecessary, so it was
deleted. Also, this commonizes the link flows for the VF to all call
ice_vc_notify_link_state().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we do "for (i = 0; i < pf->num_alloc_vfs; i++)" all over the
place. Many other places use macros to contain this repeated for loop,
So create the macro ice_for_each_vf(pf, i) that does the same thing.
There were a couple places we were using one loop variable and a VF
iterator, which were changed to using a local variable within the
ice_for_each_vf() macro.
Also in ice_alloc_vfs() we were setting pf->num_alloc_vfs after doing
"for (i = 0; i < num_alloc_vfs; i++)". Instead assign pf->num_alloc_vfs
right after allocating memory for the pf->vf array.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can't have more than one default VSI so prevent another VSI from
overwriting the current dflt_vsi. This was achieved by adding the
following functions:
ice_is_dflt_vsi_in_use()
- Used to check if the default VSI is already being used.
ice_is_vsi_dflt_vsi()
- Used to check if VSI passed in is in fact the default VSI.
ice_set_dflt_vsi()
- Used to set the default VSI via a switch rule
ice_clear_dflt_vsi()
- Used to clear the default VSI via a switch rule.
Also, there was no need to introduce any locking because all mailbox
events and synchronization of switch filters for the PF happen in the
service task.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the work done by Alex Duyck on other Intel drivers, add code to
support UDP segmentation offload (USO) for the ice driver.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively. Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the
ip -s link show dev <PF> command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We use &pf->dev->pdev all over the code. Add a simple
macro to do this for us. When multiple de-references
like this are being done add a local struct device
variable.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In situations where we alloc and free memory within the same function do
not use the devm_* variants; use regular alloc and free functions. Remove
any unused vars if there are no usages after these changes.
Also, replace an allocate and copy with kmemdup() and remove an
unnecessary memset() to 0 after a kzalloc().
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the return value from the Download Package AQ command is stored in
hw->pkg_dwnld_status, use that instead of sq_last_status since that may
have the return value from some other AQ command leading to unexpected
results.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
