[ Upstream commit 3e38f946062b4845961ab86b726651b4457b2af8 ]
If an input changes state during wake-up and is used as an interrupt
source, the IRQ handler reads the volatile input register to clear the
interrupt mask and deassert the IRQ line. However, the IRQ handler is
triggered before access to the register is granted, causing the read
operation to fail.
As a result, the IRQ handler enters a loop, repeatedly printing the
"failed reading register" message, until `pca953x_resume()` is eventually
called, which restores the driver context and enables access to
registers.
Fix by disabling the IRQ line before entering suspend mode, and
re-enabling it after the driver context is restored in `pca953x_resume()`.
An IRQ can be disabled with disable_irq() and still wake the system as
long as the IRQ has wake enabled, so the wake-up functionality is
preserved.
Fixes: b765743005 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Cc: stable@vger.kernel.org
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250512095441.31645-1-francesco@dolcini.it
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e471b784a ]
Use macros defined in linux/cleanup.h to automate resource lifetime
control in gpio-pca953x.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 3e38f946062b ("gpio: pca953x: fix IRQ storm on system wake up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5bde6201 ]
Split regcache handling to the respective helpers. It will allow to
have further refactoring with ease.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 3e38f946062b ("gpio: pca953x: fix IRQ storm on system wake up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c20a395f9b ]
Do not imply that some of the generic headers may be always included.
Instead, include explicitly what we are direct user of.
While at it, sort headers alphabetically.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: 3e38f946062b ("gpio: pca953x: fix IRQ storm on system wake up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c5672e310ad971d408752fce7596ed27adc6008f upstream.
Device can be unbound, so driver must also release memory for the wakeup
source.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250406202245.53854-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8323f3a69de6f6e96bf22f32dd8e2920766050c2 upstream.
When the Tegra186 GPIO controller is probed through ACPI matching,
the driver emits two error messages during probing:
"tegra186-gpio NVDA0508:00: invalid resource (null)"
"tegra186-gpio NVDA0508:00: invalid resource (null)"
Fix this by getting resource first and then do the ioremap.
Fixes: 2606e7c9f5 ("gpio: tegra186: Add ACPI support")
Cc: stable@vger.kernel.org
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250327032349.78809-1-kanie@linux.alibaba.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 391b41f983bf7ff853de44704d8e14e7cc648a9b ]
of_parse_phandle_with_fixed_args() requires its caller to
call into of_node_put() on the node pointer from the output
structure, but such a call is currently missing.
Call into of_node_put() to rectify that.
Fixes: 159f8a0209 ("gpio-rcar: Add DT support")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250305163753.34913-2-fabrizio.castro.jz@renesas.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 12f65d1203507f7db3ba59930fe29a3b8eee9945 upstream.
Both new_device_store and delete_device_store touch module global
resources (e.g. gpio_aggregator_lock). To prevent race conditions with
module unload, a reference needs to be held.
Add try_module_get() in these handlers.
For new_device_store, this eliminates what appears to be the most dangerous
scenario: if an id is allocated from gpio_aggregator_idr but
platform_device_register has not yet been called or completed, a concurrent
module unload could fail to unregister/delete the device, leaving behind a
dangling platform device/GPIO forwarder. This can result in various issues.
The following simple reproducer demonstrates these problems:
#!/bin/bash
while :; do
# note: whether 'gpiochip0 0' exists or not does not matter.
echo 'gpiochip0 0' > /sys/bus/platform/drivers/gpio-aggregator/new_device
done &
while :; do
modprobe gpio-aggregator
modprobe -r gpio-aggregator
done &
wait
Starting with the following warning, several kinds of warnings will appear
and the system may become unstable:
------------[ cut here ]------------
list_del corruption, ffff888103e2e980->next is LIST_POISON1 (dead000000000100)
WARNING: CPU: 1 PID: 1327 at lib/list_debug.c:56 __list_del_entry_valid_or_report+0xa3/0x120
[...]
RIP: 0010:__list_del_entry_valid_or_report+0xa3/0x120
[...]
Call Trace:
<TASK>
? __list_del_entry_valid_or_report+0xa3/0x120
? __warn.cold+0x93/0xf2
? __list_del_entry_valid_or_report+0xa3/0x120
? report_bug+0xe6/0x170
? __irq_work_queue_local+0x39/0xe0
? handle_bug+0x58/0x90
? exc_invalid_op+0x13/0x60
? asm_exc_invalid_op+0x16/0x20
? __list_del_entry_valid_or_report+0xa3/0x120
gpiod_remove_lookup_table+0x22/0x60
new_device_store+0x315/0x350 [gpio_aggregator]
kernfs_fop_write_iter+0x137/0x1f0
vfs_write+0x262/0x430
ksys_write+0x60/0xd0
do_syscall_64+0x6c/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: 828546e242 ("gpio: Add GPIO Aggregator")
Cc: stable@vger.kernel.org
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Link: https://lore.kernel.org/r/20250224143134.3024598-2-koichiro.den@canonical.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9644fbfbcab13da7f8b37bef7c51e5b8407d031 upstream.
The stmpe_reg_read function can fail, but its return value is not checked
in stmpe_gpio_irq_sync_unlock. This can lead to silent failures and
incorrect behavior if the hardware access fails.
This patch adds checks for the return value of stmpe_reg_read. If the
function fails, an error message is logged and the function returns
early to avoid further issues.
Fixes: b888fb6f2a ("gpio: stmpe: i2c transfer are forbiden in atomic context")
Cc: stable@vger.kernel.org # 4.16+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20250212021849.275-1-vulab@iscas.ac.cn
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8743d66979e494c5378563e6b5a32e913380abd8 upstream.
Spurious immediate wake up events are reported on Acer Nitro ANV14. GPIO 11 is
specified as an edge triggered input and also a wake source but this pin is
supposed to be an output pin for an LED, so it's effectively floating.
Block the interrupt from getting set up for this GPIO on this device.
Cc: stable@vger.kernel.org
Reported-by: Delgan <delgan.py@gmail.com>
Tested-by: Delgan <delgan.py@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3954
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Mika Westerberg <westeri@kernel.org>
Link: https://lore.kernel.org/r/20250211203222.761206-1-superm1@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57f5db77a915cc29461a679a6bcae7097967be1a ]
The settings for all GPIOs are locked by default in bcm_kona_gpio_reset.
The settings for a GPIO are unlocked when requesting it as a GPIO, but
not when requesting it as an interrupt, causing the IRQ settings to not
get applied.
Fix this by making sure to unlock the right bits when an IRQ is requested.
To avoid a situation where an IRQ being released causes a lock despite
the same GPIO being used by a GPIO request or vice versa, add an unlock
counter and only lock if it reaches 0.
Fixes: 757651e3d6 ("gpio: bcm281xx: Add GPIO driver")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-2-409135eab780@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de1d0d160f64ee76df1d364d521b2faf465a091c ]
The GPIO lock/unlock functions clear/write a bit to the relevant
register for each bank. However, due to an oversight the bit that
was being written was based on the total GPIO number, not the index
of the GPIO within the relevant bank, causing it to fail for any
GPIO above 32 (thus any GPIO for banks above bank 0).
Fix lock/unlock for these banks by using the correct bit.
Fixes: bdb93c03c5 ("gpio: bcm281xx: Centralize register locking")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-1-409135eab780@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4c7fcbf507 upstream.
The irqchip field has been removed from struct xgpio_instance so remove
the doc as well.
Fixes: b4510f8fd5 ("gpio: xilinx: Convert to immutable irq_chip")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312150239.IyuTVvrL-lkp@intel.com/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6179f6c6204f9932aed3a7a2100b4a295dfed9d ]
The GPIO drivers with latch interrupt support (typically types starting
with PCAL) have interrupt status registers to determine which particular
inputs have caused an interrupt. Unfortunately there is no atomic
operation to read these registers and clear the interrupt. Clearing the
interrupt is done by reading the input registers.
The code was reading the interrupt status registers, and then reading
the input registers. If an input changed between these two events it was
lost.
The solution in this patch is to revert to the non-latch version of
code, i.e. remembering the previous input status, and looking for the
changes. This system results in no more I2C transfers, so is no slower.
The latch property of the device still means interrupts will still be
noticed if the input changes back to its initial state.
Fixes: 44896beae6 ("gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240606033102.2271916-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4510f8fd5 ]
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 9860370c2172 ("gpio: xilinx: Convert gpio_lock to raw spinlock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b049e7abe9001a780d58e78e3833dcceee22f396 ]
struct platform_device::id was only set by board code, but since i.MX
became a devicetree-only platform, this will always be -1
(PLATFORM_DEVID_NONE).
Note: of_alias_get_id() returns a negative number on error and base
treats all negative errors the same, so we need not add any additional
error handling.
Fixes: 0f2c7af45d ("gpio: mxc: Convert the driver to DT-only")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20250113-b4-imx-gpio-base-warning-v1-3-0a28731a5cf6@pengutronix.de
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 02f6b0e1ec upstream.
The use-after-free issue occurs as follows: when the GPIO chip device file
is being closed by invoking gpio_chrdev_release(), watched_lines is freed
by bitmap_free(), but the unregistration of lineinfo_changed_nb notifier
chain failed due to waiting write rwsem. Additionally, one of the GPIO
chip's lines is also in the release process and holds the notifier chain's
read rwsem. Consequently, a race condition leads to the use-after-free of
watched_lines.
Here is the typical stack when issue happened:
[free]
gpio_chrdev_release()
--> bitmap_free(cdev->watched_lines) <-- freed
--> blocking_notifier_chain_unregister()
--> down_write(&nh->rwsem) <-- waiting rwsem
--> __down_write_common()
--> rwsem_down_write_slowpath()
--> schedule_preempt_disabled()
--> schedule()
[use]
st54spi_gpio_dev_release()
--> gpio_free()
--> gpiod_free()
--> gpiod_free_commit()
--> gpiod_line_state_notify()
--> blocking_notifier_call_chain()
--> down_read(&nh->rwsem); <-- held rwsem
--> notifier_call_chain()
--> lineinfo_changed_notify()
--> test_bit(xxxx, cdev->watched_lines) <-- use after free
The side effect of the use-after-free issue is that a GPIO line event is
being generated for userspace where it shouldn't. However, since the chrdev
is being closed, userspace won't have the chance to read that event anyway.
To fix the issue, call the bitmap_free() function after the unregistration
of lineinfo_changed_nb notifier chain.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Link: https://lore.kernel.org/r/20240505141156.2944912-1-quic_zhonhan@quicinc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bruno VERNAY <bruno.vernay@se.com>
Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 050b23d081da0f29474de043e9538c1f7a351b3b ]
devm_kasprintf() can return a NULL pointer on failure,but this
returned value in grgpio_probe is not checked.
Add NULL check in grgpio_probe, to handle kernel NULL
pointer dereference error.
Cc: stable@vger.kernel.org
Fixes: 7eb6ce2f27 ("gpio: Convert to using %pOF instead of full_name")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20241114091822.78199-1-hanchunchao@inspur.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d036ae41cebdfae92666024163c109b8fef516fa ]
Instead of dereferencing the platform device pointer repeatedly, just
store its address in a helper variable.
Link: https://lore.kernel.org/r/20241015131832.44678-3-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 050b23d081da ("gpio: grgpio: Add NULL check in grgpio_probe")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 72cef64180de04a7b055b4773c138d78f4ebdb77 upstream.
Setting GPIO direction = high, sometimes results in GPIO value = 0.
If a GPIO is pulled high, the following construction results in the
value being 0 when the desired value is 1:
$ echo "high" > /sys/class/gpio/gpio336/direction
$ cat /sys/class/gpio/gpio336/value
0
Before the GPIO direction is changed from an input to an output,
exar_set_value() is called with value = 1, but since the GPIO is an
input when exar_set_value() is called, _regmap_update_bits() reads a 1
due to an external pull-up. regmap_set_bits() sets force_write =
false, so the value (1) is not written. When the direction is then
changed, the GPIO becomes an output with the value of 0 (the hardware
default).
regmap_write_bits() sets force_write = true, so the value is always
written by exar_set_value() and an external pull-up doesn't affect the
outcome of setting direction = high.
The same can happen when a GPIO is pulled low, but the scenario is a
little more complicated.
$ echo high > /sys/class/gpio/gpio351/direction
$ cat /sys/class/gpio/gpio351/value
1
$ echo in > /sys/class/gpio/gpio351/direction
$ cat /sys/class/gpio/gpio351/value
0
$ echo low > /sys/class/gpio/gpio351/direction
$ cat /sys/class/gpio/gpio351/value
1
Fixes: 36fb7218e8 ("gpio: exar: switch to using regmap")
Co-developed-by: Matthew McClain <mmcclain@noprivs.com>
Signed-off-by: Matthew McClain <mmcclain@noprivs.com>
Signed-off-by: Sai Kumar Cholleti <skmr537@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241105071523.2372032-1-skmr537@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1bb5a99e1f ]
Performing a dummy read ensures that the register write operation is fully
completed, mitigating any potential bus delays that could otherwise impact
the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to
control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application
sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on
a delay function to ensure the clock frequency does not exceed 1 MHz.
However, this can lead to rapid toggling of the GPIO because the write
operation is POSTed and does not wait for a bus acknowledgment.
Fixes: 361b79119a ("gpio: Add Aspeed driver")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20241008081450.1490955-2-billy_tsai@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3360d41f4a upstream.
On a few platforms such as TI's AM69 device, disable_irq() fails to keep
track of the interrupts that happen between disable_irq() and
enable_irq() and those interrupts are missed. Use the ->irq_unmask() and
->irq_mask() methods instead of ->irq_enable() and ->irq_disable() to
correctly keep track of edges when disable_irq is called.
This solves the issue of disable_irq() not working as expected on such
platforms.
Fixes: 23265442b0 ("ARM: davinci: irq_data conversion.")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240828133207.493961-1-parth105105@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d795848ecc upstream.
Userspace may trigger a speculative read of an address outside the gpio
descriptor array.
Users can do that by calling gpio_ioctl() with an offset out of range.
Offset is copied from user and then used as an array index to get
the gpio descriptor without sanitization in gpio_device_get_desc().
This change ensures that the offset is sanitized by using
array_index_nospec() to mitigate any possibility of speculative
information leaks.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Link: https://lore.kernel.org/r/20240523085332.1801-1-hagarhem@amazon.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b440396387 upstream.
linereq_set_config() behaves badly when direction is not set.
The configuration validation is borrowed from linereq_create(), where,
to verify the intent of the user, the direction must be set to in order to
effect a change to the electrical configuration of a line. But, when
applied to reconfiguration, that validation does not allow for the unset
direction case, making it possible to clear flags set previously without
specifying the line direction.
Adding to the inconsistency, those changes are not immediately applied by
linereq_set_config(), but will take effect when the line value is next get
or set.
For example, by requesting a configuration with no flags set, an output
line with GPIO_V2_LINE_FLAG_ACTIVE_LOW and GPIO_V2_LINE_FLAG_OPEN_DRAIN
set could have those flags cleared, inverting the sense of the line and
changing the line drive to push-pull on the next line value set.
Skip the reconfiguration of lines for which the direction is not set, and
only reconfigure the lines for which direction is set.
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240626052925.174272-3-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a513552642 ]
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Fixes: 7687a5b0ee ("gpio: modepin: Add driver support for modepin GPIO controller")
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240902115848.904227-1-liaochen4@huawei.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfc6444b57 ]
Ensure that `i2c_lock' is held when setting interrupt latch and mask in
pca953x_irq_bus_sync_unlock() in order to avoid races.
The other (non-probe) call site pca953x_gpio_set_multiple() ensures the
lock is held before calling pca953x_write_regs().
The problem occurred when a request raced against irq_bus_sync_unlock()
approximately once per thousand reboots on an i.MX8MP based system.
* Normal case
0-0022: write register AI|3a {03,02,00,00,01} Input latch P0
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
* Race case
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|08 {03,02,00,00,01} *** Wrong register ***
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Link: https://lore.kernel.org/r/20240620042915.2173-1-ian.ray@gehealthcare.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9919cce62f ]
linehandle_set_config() behaves badly when direction is not set.
The configuration validation is borrowed from linehandle_create(), where,
to verify the intent of the user, the direction must be set to in order
to effect a change to the electrical configuration of a line. But, when
applied to reconfiguration, that validation does not allow for the unset
direction case, making it possible to clear flags set previously without
specifying the line direction.
Adding to the inconsistency, those changes are not immediately applied by
linehandle_set_config(), but will take effect when the line value is next
get or set.
For example, by requesting a configuration with no flags set, an output
line with GPIOHANDLE_REQUEST_ACTIVE_LOW and GPIOHANDLE_REQUEST_OPEN_DRAIN
requested could have those flags cleared, inverting the sense of the line
and changing the line drive to push-pull on the next line value set.
Ensure the intent of the user by disallowing configurations which do not
have direction set, returning an error to userspace to indicate that the
configuration is invalid.
And, for clarity, use lflags, a local copy of gcnf.flags, throughout when
dealing with the requested flags, rather than a mixture of both.
Fixes: e588bb1eae ("gpio: add new SET_CONFIG ioctl() to gpio chardev")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240626052925.174272-2-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aa9b96e9a ]
Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken
DT due to any error this value can be any. Without this value validation
there can be out of chips->irqs array boundaries access in
davinci_gpio_probe().
Validate the obtained nirq value so that it won't exceed the maximum
number of IRQs per bank.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: eb3744a2dd ("gpio: davinci: Do not assume continuous IRQ numbering")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Link: https://lore.kernel.org/r/20240618144344.16943-1-amishin@t-argos.ru
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90dd7de4ef ]
The TQMx86 GPIO controller only supports falling and rising edge
triggers, but not both. Fix this by implementing a software both-edge
mode that toggles the edge type after every interrupt.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Co-developed-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/515324f0491c4d44f4ef49f170354aca002d81ef.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08af509efd ]
irq_set_type() should not implicitly unmask the IRQ.
All accesses to the interrupt configuration register are moved to a new
helper tqmx86_gpio_irq_config(). We also introduce the new rule that
accessing irq_type must happen while locked, which will become
significant for fixing EDGE_BOTH handling.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/6aa4f207f77cb58ef64ffb947e91949b0f753ccd.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e43827b6a ]
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 08af509efd ("gpio: tqmx86: store IRQ trigger type and unmask status separately")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d6a811b52 ]
The TQMx86 GPIO controller uses the same register address for input and
output data. Reading the register will always return current inputs
rather than the previously set outputs (regardless of the current
direction setting). Therefore, using a RMW pattern does not make sense
when setting output values. Instead, the previously set output register
value needs to be stored as a shadow register.
As there is no reliable way to get the current output values from the
hardware, also initialize all channels to 0, to ensure that stored and
actual output values match. This should usually not have any effect in
practise, as the TQMx86 UEFI sets all outputs to 0 during boot.
Also prepare for extension of the driver to more than 8 GPIOs by using
DECLARE_BITMAP.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/d0555933becd45fa92a85675d26e4d59343ddc01.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a5e9306b8 ]
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 9d6a811b52 ("gpio: tqmx86: introduce shadow register for GPIO output value")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0166b637 ]
If a line is requested with debounce, and that results in debouncing
in software, and the line is subsequently reconfigured to enable edge
detection then the allocation of the kfifo to contain edge events is
overlooked. This results in events being written to and read from an
uninitialised kfifo. Read events are returned to userspace.
Initialise the kfifo in the case where the software debounce is
already active.
Fixes: 65cff70464 ("gpiolib: cdev: support setting debounce")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240510065342.36191-1-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9344e34e79 ]
Store the debounce period for a requested line locally, rather than in
the debounce_period_us field in the gpiolib struct gpio_desc.
Add a global tree of lines containing supplemental line information
to make the debounce period available to be reported by the
GPIO_V2_GET_LINEINFO_IOCTL and the line change notifier.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: ee0166b637 ("gpiolib: cdev: fix uninitialised kfifo")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52ee7c02f6 ]
Do not imply that some of the generic headers may be always included.
Instead, include explicitly what we are direct user of.
While at it, sort headers alphabetically.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Rewiewed-by: Kent Gibson <warthog618@gmail.com>
Stable-dep-of: ee0166b637 ("gpiolib: cdev: fix uninitialised kfifo")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ace0ebe5c9 ]
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c3b532ad3 ]
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f575957882 ]
The vf610 gpio driver is enabled by default for all i.MX machines,
without any option to disable it in a board-specific config file.
Most i.MX chipsets have no hardware for this driver. Change the default
to enable GPIO_VF610 for SOC_VF610 and disable it otherwise.
Add a text description after the bool type, this makes the driver
selectable by make config etc.
Fixes: 30a35c07d9 ("gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5c54a9d3 ]
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61 ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530b1dbd97 ]
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0f (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84aef4ed59 ]
The raw interrupt status of eic maybe set before the interrupt is enabled,
since the eic interrupt has a latch function, which would trigger the
interrupt event once enabled it from user side. To solve this problem,
interrupts generated before setting the interrupt trigger type are ignored.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 805c74eac8 upstream.
Spurious wakeups are reported on the GPD G1619-04 which
can be absolved by programming the GPIO to ignore wakeups.
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Melikov <mail@gmelikov.ru>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3073
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
