[ Upstream commit 9510b38dc0 ]
Adds the MMC_QUIRK_NO_UHS_DDR50_TUNING quirk and updates
mmc_execute_tuning() to return 0 if that quirk is set. This fixes an
issue on certain Swissbit SD cards that do not support DDR50 tuning
where tuning requests caused I/O errors to be thrown.
Signed-off-by: Erick Shepherd <erick.shepherd@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250331221337.1414534-1-erick.shepherd@ni.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb3bbc46c9 ]
Per the SD Host Controller Simplified Specification v4.20 §3.2.3, change
the SD card clock parameters only after first disabling the external card
clock. Doing this fixes a spurious clock pulse on Baytrail and Apollo Lake
SD controllers which otherwise breaks voltage switching with a specific
Swissbit SD card.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: Erick Shepherd <erick.shepherd@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250211214645.469279-1-erick.shepherd@ni.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cbe799ac1 ]
Add support for Exynos7870 DW MMC controllers, for both SMU and non-SMU
variants. These controllers require a quirk to access 64-bit FIFO in 32-bit
accesses (DW_MMC_QUIRK_FIFO64_32).
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250219-exynos7870-mmc-v2-3-b4255a3e39ed@disroot.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31e75ed964 ]
The SD spec version 6.0 section 6.4.1.5 requires that Vdd must be
lowered to less than 0.5V for a minimum of 1 ms when powering off a
card. Increase wait to 15 ms so that voltage has time to drain down
to 0.5V and cards can power off correctly. Issues with voltage drain
time were only observed on Apollo Lake and Bay Trail host controllers
so this fix is limited to those devices.
Signed-off-by: Erick Shepherd <erick.shepherd@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250314195021.1588090-1-erick.shepherd@ni.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57c0902f8b ]
In certain DW MMC implementations (such as in some Exynos7870
controllers), 64-bit read/write is not allowed from a 64-bit FIFO.
Add a quirk which facilitates accessing the 64-bit FIFO registers in two
32-bit halves.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250219-exynos7870-mmc-v2-2-b4255a3e39ed@disroot.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 49d1626351 upstream.
We have received reports about cards can become corrupt related to the
aggressive PM support. Let's make a partial revert of the change that
enabled the feature.
Reported-by: David Owens <daowens01@gmail.com>
Reported-by: Romain Naour <romain.naour@smile.fr>
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Fixes: 3edf588e7f ("mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20250312121712.1168007-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e51a349d2d upstream.
The error path when atmci_configure_dma() set dma fails in atmci driver
does not correctly disable the clock.
Add the missing clk_disable_unprepare() to the error path for pair with
clk_prepare_enable().
Fixes: 467e081d23 ("mmc: atmel-mci: use probe deferring if dma controller is not ready yet")
Signed-off-by: Gu Bowen <gubowen5@huawei.com>
Acked-by: Aubin Constans <aubin.constans@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250225022856.3452240-1-gubowen5@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e68abf2b9 upstream.
For hs400(es) mode, the 'hs400-ds-delay' is typically configured in the
dts. However, some projects may only define 'mediatek,hs400-ds-dly3',
which can lead to initialization failures in hs400es mode. CMD13 reported
response crc error in the mmc_switch_status() just after switching to
hs400es mode.
[ 1.914038][ T82] mmc0: mmc_select_hs400es failed, error -84
[ 1.914954][ T82] mmc0: error -84 whilst initialising MMC card
Currently, the hs400_ds_dly3 value is set within the tuning function. This
means that the PAD_DS_DLY3 field is not configured before tuning process,
which is the reason for the above-mentioned CMD13 response crc error.
Move the PAD_DS_DLY3 field configuration into msdc_prepare_hs400_tuning(),
and add a value check of hs400_ds_delay to prevent overwriting by zero when
the 'hs400-ds-delay' is not set in the dts. In addition, since hs400(es)
only tune the PAD_DS_DLY1, the PAD_DS_DLY2_SEL bit should be cleared to
bypass it.
Fixes: c4ac38c653 ("mmc: mtk-sd: Add HS400 online tuning support")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250123092644.7359-1-andy-ld.lu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20a0c37e44 ]
Qualcomm regulator supports two power supply modes: HPM and LPM.
Currently, the sdhci-msm.c driver does not set the load to adjust
the current for eMMC and SD. If the regulator dont't set correct
load in LPM state, it will lead to the inability to properly
initialize eMMC and SD.
Set the correct regulator current for eMMC and SD to ensure that the
device can work normally even when the regulator is in LPM.
Signed-off-by: Yuanjie Yang <quic_yuanjiey@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250114083514.258379-1-quic_yuanjiey@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2a44f8da2 ]
The card-quirk was added to limit the clock-rate for a card with UHS-mode
support, although let's respect the quirk for non-UHS mode too, to make the
behaviour consistent.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Message-ID: <1732268242-72799-1-git-send-email-shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 291220451c upstream.
In the probe function, it goes to 'release_mem' label and returns after
some procedure failure. But if the clocks (partial or all) have been
enabled previously, they would not be disabled in msdc_runtime_suspend,
since runtime PM is not yet enabled for this case.
That cause mmc related clocks always on during system suspend and block
suspend flow. Below log is from a SDCard issue of MT8196 chromebook, it
returns -ETIMEOUT while polling clock stable in the msdc_ungate_clock()
and probe failed, but the enabled clocks could not be disabled anyway.
[ 129.059253] clk_chk_dev_pm_suspend()
[ 129.350119] suspend warning: msdcpll is on
[ 129.354494] [ck_msdc30_1_sel : enabled, 1, 1, 191999939, ck_msdcpll_d2]
[ 129.362787] [ck_msdcpll_d2 : enabled, 1, 1, 191999939, msdcpll]
[ 129.371041] [ck_msdc30_1_ck : enabled, 1, 1, 191999939, ck_msdc30_1_sel]
[ 129.379295] [msdcpll : enabled, 1, 1, 383999878, clk26m]
Add a new 'release_clk' label and reorder the error handle functions to
make sure the clocks be disabled after probe failure.
Fixes: ffaea6ebfe ("mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling")
Fixes: 7a2fa8eed9 ("mmc: mtk-sd: use devm_mmc_alloc_host")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Message-ID: <20241107121215.5201-1-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd068d5159 ]
GIGASTONE Gaming Plus microSD cards manufactured on 02/2022 report that
they support poweroff notification and cache, but they are not working
correctly.
Flush Cache bit never gets cleared in sd_flush_cache() and Poweroff
Notification Ready bit also never gets set to 1 within 1 second from the
end of busy of CMD49 in sd_poweroff_notify().
This leads to I/O error and runtime PM error state.
I observed that the same card manufactured on 01/2024 works as expected.
This problem seems similar to the Kingston cards fixed with
commit c467c8f081 ("mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston
Canvas Go Plus from 11/2019") and should be handled using quirks.
CID for the problematic card is here.
12345641535443002000000145016200
Manufacturer ID is 0x12 and defined as CID_MANFID_GIGASTONE as of now,
but would like comments on what naming is appropriate because MID list
is not public and not sure it's right.
Signed-off-by: Keita Aihara <keita.aihara@sony.com>
Link: https://lore.kernel.org/r/20240913094417.GA4191647@sony.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 87a0d90fcd upstream.
Disabling card detect from the host's ->shutdown_pre() callback turned out
to not be the complete solution. More precisely, beyond the point when the
mmc_bus->shutdown() has been called, to gracefully power off the card, we
need to prevent card detect. Otherwise the mmc_rescan work may poll for the
card with a CMD13, to see if it's still alive, which then will fail and
hang as the card has already been powered off.
To fix this problem, let's disable mmc_rescan prior to power off the card
during shutdown.
Reported-by: Anthony Pighin <anthony.pighin@nokia.com>
Fixes: 66c915d09b ("mmc: core: Disable card detect during shutdown")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Closes: https://lore.kernel.org/all/BN0PR08MB695133000AF116F04C3A9FFE83212@BN0PR08MB6951.namprd08.prod.outlook.com/
Tested-by: Anthony Pighin <anthony.pighin@nokia.com>
Message-ID: <20241125122446.18684-1-ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f0fa47cee upstream.
The Vexia Edu Atla 10 tablet distributed to schools in the Spanish
Andalucía region has no ACPI fwnode associated with the SDHCI controller
for its microsd-slot and thus has no ACPI GPIO resource info.
This causes the following error to be logged and the slot to not work:
[ 10.572113] sdhci-pci 0000:00:12.0: failed to setup card detect gpio
Add a DMI quirk table for providing gpiod_lookup_tables with manually
provided CD GPIO info and use this DMI table to provide the CD GPIO info
on this tablet. This fixes the microsd-slot not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Message-ID: <20241118210049.311079-1-hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 328bda09cc ]
GCC 13 complains about the truncated output of snprintf():
drivers/mmc/host/mmc_spi.c: In function ‘mmc_spi_response_get’:
drivers/mmc/host/mmc_spi.c:227:64: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^
drivers/mmc/host/mmc_spi.c:227:9: note: ‘snprintf’ output between 26 and 43 bytes into a destination of size 32
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
228 | cmd->opcode, maptype(cmd));
Drop it and fold the string it generates into the only place where it's
emitted - the dev_dbg() call at the end of the function.
Fixes: 15a0580ced ("mmc_spi host driver")
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241008160134.69934-1-brgl@bgdev.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 85b580afc2 upstream.
It turns out that the Allwinner A100/A133 SoC only supports 8K DMA
blocks (13 bits wide), for both the SD/SDIO and eMMC instances.
And while this alone would make a trivial fix, the H616 falls back to
the A100 compatible string, so we have to now match the H616 compatible
string explicitly against the description advertising 64K DMA blocks.
As the A100 is now compatible with the D1 description, let the A100
compatible string point to that block instead, and introduce an explicit
match against the H616 string, pointing to the old description.
Also remove the redundant setting of clk_delays to NULL on the way.
Fixes: 3536b82e58 ("mmc: sunxi: add support for A100 mmc controller")
Cc: stable@vger.kernel.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Parthiban Nallathambi <parthiban@linumiz.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Message-ID: <20241107014240.24669-1-andre.przywara@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1635e407a4 upstream.
The commit 8396c793ff ("mmc: dw_mmc: Fix IDMAC operation with pages
bigger than 4K") increased the max_req_size, even for 4K pages, causing
various issues:
- Panic booting the kernel/rootfs from an SD card on Rockchip RK3566
- Panic booting the kernel/rootfs from an SD card on StarFive JH7100
- "swiotlb buffer is full" and data corruption on StarFive JH7110
At this stage no fix have been found, so it's probably better to just
revert the change.
This reverts commit 8396c793ff.
Cc: stable@vger.kernel.org
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 8396c793ff ("mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K")
Closes: https://lore.kernel.org/linux-mmc/614692b4-1dbe-31b8-a34d-cb6db1909bb7@w6rz.net/
Closes: https://lore.kernel.org/linux-mmc/CAC8uq=Ppnmv98mpa1CrWLawWoPnu5abtU69v-=G-P7ysATQ2Pw@mail.gmail.com/
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-ID: <20241110114700.622372-1-aurelien@aurel32.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aea62c744a upstream.
To check if mmc cqe is in halt state, need to check set/clear of CQHCI_HALT
bit. At this time, we need to check with &, not &&.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Seunghwan Baek <sh8267.baek@samsung.com>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240829061823.3718-2-sh8267.baek@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e540da4c1 upstream.
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Fixes: bb7b8ec62d ("mmc: sdhci-of-aspeed: Add support for the ASPEED SD controller")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240826124851.379759-1-liaochen4@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8396c793ff upstream.
Commit 616f876617 ("mmc: pass queue_limits to blk_mq_alloc_disk") [1]
revealed the long living issue in dw_mmc.c driver, existing since the
time when it was first introduced in commit f95f3850f7 ("mmc: dw_mmc:
Add Synopsys DesignWare mmc host driver."), also making kernel boot
broken on platforms using dw_mmc driver with 16K or 64K pages enabled,
with this message in dmesg:
mmcblk: probe of mmc0:0001 failed with error -22
That's happening because mmc_blk_probe() fails when it calls
blk_validate_limits() consequently, which returns the error due to
failed max_segment_size check in this code:
/*
* The maximum segment size has an odd historic 64k default that
* drivers probably should override. Just like the I/O size we
* require drivers to at least handle a full page per segment.
*/
...
if (WARN_ON_ONCE(lim->max_segment_size < PAGE_SIZE))
return -EINVAL;
In case when IDMAC (Internal DMA Controller) is used, dw_mmc.c always
sets .max_seg_size to 4 KiB:
mmc->max_seg_size = 0x1000;
The comment in the code above explains why it's incorrect. Arnd
suggested setting .max_seg_size to .max_req_size to fix it, which is
also what some other drivers are doing:
$ grep -rl 'max_seg_size.*=.*max_req_size' drivers/mmc/host/ | \
wc -l
18
This change is not only fixing the boot with 16K/64K pages, but also
leads to a better MMC performance. The linear write performance was
tested on E850-96 board (eMMC only), before commit [1] (where it's
possible to boot with 16K/64K pages without this fix, to be able to do
a comparison). It was tested with this command:
# dd if=/dev/zero of=somefile bs=1M count=500 oflag=sync
Test results are as follows:
- 4K pages, .max_seg_size = 4 KiB: 94.2 MB/s
- 4K pages, .max_seg_size = .max_req_size = 512 KiB: 96.9 MB/s
- 16K pages, .max_seg_size = 4 KiB: 126 MB/s
- 16K pages, .max_seg_size = .max_req_size = 2 MiB: 128 MB/s
- 64K pages, .max_seg_size = 4 KiB: 138 MB/s
- 64K pages, .max_seg_size = .max_req_size = 8 MiB: 138 MB/s
Unfortunately, SD card controller is not enabled in E850-96 yet, so it
wasn't possible for me to run the test on some cheap SD cards to check
this patch's impact on those. But it's possible that this change might
also reduce the writes count, thus improving SD/eMMC longevity.
All credit for the analysis and the suggested solution goes to Arnd.
[1] https://lore.kernel.org/all/20240215070300.2200308-18-hch@lst.de/
Fixes: f95f3850f7 ("mmc: dw_mmc: Add Synopsys DesignWare mmc host driver.")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/all/CA+G9fYtddf2Fd3be+YShHP6CmSDNcn0ptW8qg+stUKW+Cn0rjQ@mail.gmail.com/
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240306232052.21317-1-semen.protsenko@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 469e5e4713 upstream.
Applying MMC_QUIRK_BROKEN_SD_CACHE is broken, as the card's SD quirks are
referenced in sd_parse_ext_reg_perf() prior to the quirks being initialized
in mmc_blk_probe().
To fix this problem, let's split out an SD-specific list of quirks and
apply in mmc_sd_init_card() instead. In this way, sd_read_ext_regs() to has
the available information for not assigning the SD_EXT_PERF_CACHE as one of
the (un)supported features, which in turn allows mmc_sd_init_card() to
properly skip execution of sd_enable_cache().
Fixes: c467c8f081 ("mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston Canvas Go Plus from 11/2019")
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Co-developed-by: Keita Aihara <keita.aihara@sony.com>
Signed-off-by: Keita Aihara <keita.aihara@sony.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240820230631.GA436523@sony.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9374ae912d ]
When we use cmd8 as the tuning command in hs400 mode, the command
response sent back by some eMMC devices cannot be correctly sampled
by MTK eMMC controller at some weak sample timing. In this case,
command timeout error may occur. So we must receive the following
data to make sure the next cmd8 send correctly.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Fixes: c4ac38c653 ("mmc: mtk-sd: Add HS400 online tuning support")
Cc: stable@vger.stable.com
Link: https://lore.kernel.org/r/20240716013704.10578-1-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6275c7bc8d upstream.
Fix a race condition if the clock provider comes up after mmc is probed,
this causes mmc to fail without retrying.
When given the DEFER error from the clk source, pass it on up the chain.
Fixes: f90a0612f0 ("mmc: dw_mmc: lookup for optional biu and ciu clocks")
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240811212212.123255-1-ben.whitten@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1e627af32 ]
If the "test->highmem = alloc_pages()" allocation fails then calling
__free_pages(test->highmem) will result in a NULL dereference. Also
change the error code to -ENOMEM instead of returning success.
Fixes: 2661081f5a ("mmc_test: highmem tests")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/8c90be28-67b4-4b0d-a105-034dc72a0b31@stanley.mountain
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ab069ce125 upstream.
sdhci_check_ro() can call mmc_gpio_get_ro() while holding the sdhci
host->lock spinlock. That would be a problem if the GPIO access done by
mmc_gpio_get_ro() needed to sleep.
However, host->lock is not needed anyway. The mmc core ensures that host
operations do not race with each other, and asynchronous callbacks like the
interrupt handler, software timeouts, completion work etc, cannot affect
sdhci_check_ro().
So remove the locking.
Fixes: 6d5cd068ee ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240614080051.4005-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbd64f902b upstream.
mmc_of_parse() reads device property "wp-inverted" and sets
MMC_CAP2_RO_ACTIVE_HIGH if it is true. MMC_CAP2_RO_ACTIVE_HIGH is used
to invert a write-protect (AKA read-only) GPIO value.
sdhci_get_property() also reads "wp-inverted" and sets
SDHCI_QUIRK_INVERTED_WRITE_PROTECT which is used to invert the
write-protect value as well but also acts upon a value read out from the
SDHCI_PRESENT_STATE register.
Many drivers call both mmc_of_parse() and sdhci_get_property(),
so that both MMC_CAP2_RO_ACTIVE_HIGH and
SDHCI_QUIRK_INVERTED_WRITE_PROTECT will be set if the controller has
device property "wp-inverted".
Amend the logic in sdhci_check_ro() to allow for that possibility,
so that the write-protect value is not inverted twice.
Also do not invert the value if it is a negative error value. Note that
callers treat an error the same as not-write-protected, so the result is
functionally the same in that case.
Also do not invert the value if sdhci host operation ->get_ro() is used.
None of the users of that callback set SDHCI_QUIRK_INVERTED_WRITE_PROTECT
directly or indirectly, but two do call mmc_gpio_get_ro(), so leave it to
them to deal with that if they ever set SDHCI_QUIRK_INVERTED_WRITE_PROTECT
in the future.
Fixes: 6d5cd068ee ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240614080051.4005-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebc4fc34ea upstream.
jmicron_pmos() and sdhci_pci_probe() use pci_{read,write}_config_byte()
that return PCIBIOS_* codes. The return code is then returned as is by
jmicron_probe() and sdhci_pci_probe(). Similarly, the return code is
also returned as is from jmicron_resume(). Both probe and resume
functions should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning them the fix these issues.
Fixes: 7582041ff3 ("mmc: sdhci-pci: fix simple_return.cocci warnings")
Fixes: 45211e2159 ("sdhci: toggle JMicron PMOS setting")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240527132443.14038-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d77dc388cd upstream.
When erase/trim/discard completion was converted to mmc_poll_for_busy(),
optional support to poll with the host_ops->card_busy() callback was also
added.
The common sdhci's ->card_busy() turns out not to be working as expected
for the sdhci-brcmstb variant, as it keeps returning busy beyond the card's
busy period. In particular, this leads to the below splat for
mmc_do_erase() when running a discard (BLKSECDISCARD) operation during
mkfs.f2fs:
Info: [/dev/mmcblk1p9] Discarding device
[ 39.597258] sysrq: Show Blocked State
[ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d
[ 39.610609] Call trace:
[ 39.613098] __switch_to+0xd8/0xf4
[ 39.616582] __schedule+0x440/0x4f4
[ 39.620137] schedule+0x2c/0x48
[ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114
[ 39.628562] schedule_hrtimeout_range+0x10/0x18
[ 39.633169] usleep_range_state+0x5c/0x90
[ 39.637253] __mmc_poll_for_busy+0xec/0x128
[ 39.641514] mmc_poll_for_busy+0x48/0x70
[ 39.645511] mmc_do_erase+0x1ec/0x210
[ 39.649237] mmc_erase+0x1b4/0x1d4
[ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac
[ 39.657037] mmc_mq_queue_rq+0x18c/0x214
[ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528
[ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac
[ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c
[ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c
[ 39.680668] blk_mq_flush_plug_list+0x200/0x33c
[ 39.685278] blk_add_rq_to_plug+0x68/0xd8
[ 39.689365] blk_mq_submit_bio+0x3a4/0x458
[ 39.693539] __submit_bio+0x1c/0x80
[ 39.697096] submit_bio_noacct_nocheck+0x94/0x174
[ 39.701875] submit_bio_noacct+0x1b0/0x22c
[ 39.706042] submit_bio+0xac/0xe8
[ 39.709424] blk_next_bio+0x4c/0x5c
[ 39.712973] blkdev_issue_secure_erase+0x118/0x170
[ 39.717835] blkdev_common_ioctl+0x374/0x728
[ 39.722175] blkdev_ioctl+0x8c/0x2b0
[ 39.725816] vfs_ioctl+0x24/0x40
[ 39.729117] __arm64_sys_ioctl+0x5c/0x8c
[ 39.733114] invoke_syscall+0x68/0xec
[ 39.736839] el0_svc_common.constprop.0+0x70/0xd8
[ 39.741609] do_el0_svc+0x18/0x20
[ 39.744981] el0_svc+0x68/0x94
[ 39.748107] el0t_64_sync_handler+0x88/0x124
[ 39.752455] el0t_64_sync+0x168/0x16c
To fix the problem let's override the host_ops->card_busy() callback by
setting it to NULL, which forces the mmc core to poll with a CMD13 and
checking the R1_STATUS in the mmc_busy_cb() function.
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Fixes: 0d84c3e6a5 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240603220834.21989-2-kamal.dasu@broadcom.com
[Ulf: Clarified the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55c421b364 ]
Using __exit for the remove function results in the remove callback being
discarded with CONFIG_MMC_DAVINCI=y. When such a device gets unbound (e.g.
using sysfs or hotplug), the driver is just removed without the cleanup
being performed. This results in resource leaks. Fix it by compiling in the
remove callback unconditionally.
This also fixes a W=1 modpost warning:
WARNING: modpost: drivers/mmc/host/davinci_mmc: section mismatch in
reference: davinci_mmcsd_driver+0x10 (section: .data) ->
davinci_mmcsd_remove (section: .exit.text)
Fixes: b4cff4549b ("DaVinci: MMC: MMC/SD controller driver for DaVinci family")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240324114017.231936-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 431946c0f6 upstream.
The card-detect GPIO for the microSD slot on Asus T100TA / T100TAM models
stopped working under Linux after commit 6fd03f0248 ("gpiolib: acpi:
support bias pull disable").
The GPIO in question is connected to a mechanical switch in the slot
which shorts the pin to GND when a card is inserted.
The GPIO pin correctly gets configured with a 20K pull-up by the BIOS,
but there is a bug in the DSDT where the GpioInt for the card-detect is
configured with a PullNone setting:
GpioInt (Edge, ActiveBoth, SharedAndWake, PullNone, 0x2710,
"\\_SB.GPO0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0026
}
Linux now actually honors the PullNone setting and disables the 20K pull-up
configured by the BIOS.
Add a new DMI_QUIRK_SD_CD_ENABLE_PULL_UP quirk which when set calls
mmc_gpiod_set_cd_config() to re-enable the pull-up and set this for
the Asus T100TA models to fix this.
Fixes: 6fd03f0248 ("gpiolib: acpi: support bias pull disable")
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-7-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef3eab75e1 upstream.
On the Toshiba WT10-A the microSD slot always reports the card being
write-protected, just like on the Toshiba WT8-B.
Add a DMI quirk to work around this.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-6-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3521d7cba upstream.
The Lenovo Yoga Tablet 2 Pro 1380 sdcard slot has an active high cd pin
and a broken wp pin which always reports the card being write-protected.
Add a DMI quirk to address both issues.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-5-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63a7cd6602 upstream.
Some mmc host drivers may need to fixup a card-detection GPIO's config
to e.g. enable the GPIO controllers builtin pull-up resistor on devices
where the firmware description of the GPIO is broken (e.g. GpioInt with
PullNone instead of PullUp in ACPI DSDT).
Since this is the exception rather then the rule adding a config
parameter to mmc_gpiod_request_cd() seems undesirable, so instead
add a new mmc_gpiod_set_cd_config() function. This is simply a wrapper
to call gpiod_set_config() on the card-detect GPIO acquired through
mmc_gpiod_request_cd().
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67380251e8 upstream.
Requesting a retune before switching to the RPMB partition has been
observed to cause CRC errors on the RPMB reads (-EILSEQ).
Since RPMB reads can not be retried, the clients would be directly
affected by the errors.
This commit disables the retune request prior to switching to the RPMB
partition: mmc_retune_pause() no longer triggers a retune before the
pause period begins.
This was verified with the sdhci-of-arasan driver (ZynqMP) configured
for HS200 using two separate eMMC cards (DG4064 and 064GB2). In both
cases, the error was easy to reproduce triggering every few tenths of
reads.
With this commit, systems that were utilizing OP-TEE to access RPMB
variables will experience an enhanced performance. Specifically, when
OP-TEE is configured to employ RPMB as a secure storage solution, it not
only writes the data but also the secure filesystem within the
partition. As a result, retrieving any variable involves multiple RPMB
reads, typically around five.
For context, on ZynqMP, each retune request consumed approximately
8ms. Consequently, reading any RPMB variable used to take at the very
minimum 40ms.
After droping the need to retune before switching to the RPMB partition,
this is no longer the case.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240103112911.2954632-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3182932bb ]
While STRB is currently used for DATA and CRC responses, the CMD
responses from the device to the host still require ITAPDLY for
HS400 timing.
Currently what is stored for HS400 is the ITAPDLY from High Speed
mode which is incorrect. The ITAPDLY for HS400 speed mode should
be the same as ITAPDLY as HS200 timing after tuning is executed.
Add the functionality to save ITAPDLY from HS200 tuning and save
as HS400 ITAPDLY.
Fixes: a161c45f29 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-8-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dff65bb5e ]
Add ITAPDLYSEL to sdhci_j721e_4bit_set_clock function.
This allows to set the correct ITAPDLY for timings that
do not carry out tuning.
Fixes: 1accbced1c ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-7-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 387c1bf7dc ]
Currently the OTAP/ITAP delay enable functionality is incorrect in
the am654_set_clock function. The OTAP delay is not enabled when
timing < SDR25 bus speed mode. The ITAP delay is not enabled for
timings that do not carry out tuning.
Add this OTAP/ITAP delay functionality according to the datasheet
[1] OTAPDLYENA and ITAPDLYENA for MMC0.
[1] https://www.ti.com/lit/ds/symlink/am62p.pdf
Fixes: 8ee5fc0e0b ("mmc: sdhci_am654: Update OTAPDLY writes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-4-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cb2f9286a ]
ti,otap-del-sel has been deprecated since v5.7 and there are no users of
this property and no documentation in the DT bindings either.
Drop the fallback code looking for this property, this makes
sdhci_am654_get_otap_delay() much easier to read as all the TAP values
can be handled via a single iterator loop.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231122060215.2074799-1-vigneshr@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 387c1bf7dc ("mmc: sdhci_am654: Add OTAP/ITAP delay enable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d465234493 ]
For DDR52 timing, DLL is enabled but tuning is not carried
out, therefore the ITAPDLY value in PHY CTRL 4 register is
not correct. Fix this by writing ITAPDLY after enabling DLL.
Fixes: a161c45f29 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-3-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6231d99dd4 ]
Currently the sdhci_am654 driver only supports one tuning
algorithm which should be used only when DLL is enabled. The
ITAPDLY is selected from the largest passing window and the
buffer is viewed as a circular buffer.
The new algorithm should be used when the delay chain
is enabled. The ITAPDLY is selected from the largest passing
window and the buffer is not viewed as a circular buffer.
This implementation is based off of the following paper: [1].
Also add support for multiple failing windows.
[1] https://www.ti.com/lit/an/spract9/spract9.pdf
Fixes: 13ebeae68a ("mmc: sdhci_am654: Add support for software tuning")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-2-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 77e01b49e3 upstream.
During the initialization to HS400es stage, add a HS400 tuning flow as an
optional process. For Mediatek IP, the HS400es mode requires a specific
tuning to ensure the correct HS400 timing setting.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Link: https://lore.kernel.org/r/20231225093839.22931-2-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "Lin Gui (桂林)" <Lin.Gui@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8def10f73 upstream.
Generic sdhci code registers LED device and uses host->runtime_suspended
flag to protect access to it. The sdhci-msm driver doesn't set this flag,
which causes a crash when LED is accessed while controller is runtime
suspended. Fix this by setting the flag correctly.
Cc: stable@vger.kernel.org
Fixes: 67e6db113c ("mmc: sdhci-msm: Add pm_runtime and system PM support")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240321-sdhci-mmc-suspend-v1-1-fbc555a64400@8devices.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
