[ Upstream commit 5612d6d51e ]
When an IOCTL times out and driver issues a target reset, if firmware
fails the task management elevate the recovery by issuing a diag reset to
controller.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Link: https://lore.kernel.org/r/1739410016-27503-5-git-send-email-shivasharan.srikanteshwara@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad7c3c0cb8 ]
Currently, the code does:
if (x == 0) {
x &= ~0x3;
x |= 0x1;
}
Zeroing bits 0 and 1 of a variable that is 0 is not necessary. So directly
set the variable to 1.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20241212221817.78940-2-pmenzel@molgen.mpg.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f5eb062e8 ]
Issue a Diag-Reset when the "Doorbell-In-Use" bit is set during the
driver load/initialization.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110173341.11595-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 82dbb57ac8 upstream.
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT
ZONES command reply buffer from ATA-ZAC devices by directly accessing the
buffer in the host memory. This does not respect the default command DMA
direction and causes IOMMU page faults on architectures with an IOMMU
enforcing write-only mappings for DMA_FROM_DEVICE DMA driection (e.g. AMD
hosts).
scsi 18:0:0:0: Direct-Access-ZBC ATA WDC WSH722020AL W870 PQ: 0 ANSI: 6
scsi 18:0:0:0: SATA: handle(0x0027), sas_addr(0x300062b2083e7c40), phy(0), device_name(0x5000cca29dc35e11)
scsi 18:0:0:0: enclosure logical id (0x300062b208097c40), slot(0)
scsi 18:0:0:0: enclosure level(0x0000), connector name( C0.0)
scsi 18:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
scsi 18:0:0:0: qdepth(32), tagged(1), scsi_level(7), cmd_que(1)
sd 18:0:0:0: Attached scsi generic sg2 type 20
sd 18:0:0:0: [sdc] Host-managed zoned block device
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b200 flags=0x0050]
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b300 flags=0x0050]
mpt3sas_cm0: mpt3sas_ctl_pre_reset_handler: Releasing the trace buffer due to adapter reset.
mpt3sas_cm0 fault info from func: mpt3sas_base_make_ioc_ready
mpt3sas_cm0: fault_state(0x2666)!
mpt3sas_cm0: sending diag reset !!
mpt3sas_cm0: diag reset: SUCCESS
sd 18:0:0:0: [sdc] REPORT ZONES start lba 0 failed
sd 18:0:0:0: [sdc] REPORT ZONES: Result: hostbyte=DID_RESET driverbyte=DRIVER_OK
sd 18:0:0:0: [sdc] 0 4096-byte logical blocks: (0 B/0 B)
Avoid such issue by always mapping the buffer of REPORT ZONES commands
using DMA_BIDIRECTIONAL (read+write IOMMU mapping). This is done by
introducing the helper function _base_scsi_dma_map() and using this helper
in _base_build_sg_scmd() and _base_build_sg_scmd_ieee() instead of calling
directly scsi_dma_map().
Fixes: 471ef9d4e4 ("mpt3sas: Build MPI SGL LIST on GEN2 HBAs and IEEE SGL LIST on GEN3 HBAs")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240719073913.179559-3-dlemoal@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4254dfeda8 upstream.
There is a potential out-of-bounds access when using test_bit() on a single
word. The test_bit() and set_bit() functions operate on long values, and
when testing or setting a single word, they can exceed the word
boundary. KASAN detects this issue and produces a dump:
BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas
Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965
For full log, please look at [1].
Make the allocation at least the size of sizeof(unsigned long) so that
set_bit() and test_bit() have sufficient room for read/write operations
without overwriting unallocated memory.
[1] Link: https://lore.kernel.org/all/ZkNcALr3W3KGYYJG@gmail.com/
Fixes: c696f7b83e ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Cc: stable@vger.kernel.org
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240605085530.499432-1-leitao@debian.org
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90e6f08915 upstream.
The function mpi3mr_qcmd() of the mpi3mr driver is able to indicate to
the HBA if a read or write command directed at an ATA device should be
translated to an NCQ read/write command with the high prioiryt bit set
when the request uses the RT priority class and the user has enabled NCQ
priority through sysfs.
However, unlike the mpt3sas driver, the mpi3mr driver does not define
the sas_ncq_prio_supported and sas_ncq_prio_enable sysfs attributes, so
the ncq_prio_enable field of struct mpi3mr_sdev_priv_data is never
actually set and NCQ Priority cannot ever be used.
Fix this by defining these missing atributes to allow a user to check if
an ATA device supports NCQ priority and to enable/disable the use of NCQ
priority. To do this, lift the function scsih_ncq_prio_supp() out of the
mpt3sas driver and make it the generic SCSI SAS transport function
sas_ata_ncq_prio_supported(). Nothing in that function is hardware
specific, so this function can be used in both the mpt3sas driver and
the mpi3mr driver.
Reported-by: Scott McCoy <scott.mccoy@wdc.com>
Fixes: 023ab2a9b4 ("scsi: mpi3mr: Add support for queue command processing")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240611083435.92961-1-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee0017c3ed ]
If the driver detects that the controller is not ready before sending the
first IOC facts command, it will wait for a maximum of 10 seconds for it to
become ready. However, even if the controller becomes ready within 10
seconds, the driver will still issue a diagnostic reset.
Modify the driver to avoid sending a diag reset if the controller becomes
ready within the 10-second wait time.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240221071724.14986-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3c978492c3 upstream.
The retry loop continues to iterate until the count reaches 30, even after
receiving the correct value. Exit loop when a non-zero value is read.
Fixes: 4ca10f3e31 ("scsi: mpt3sas: Perform additional retries if doorbell read returns 0")
Cc: stable@vger.kernel.org
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20231020105849.6350-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e40c04ade0 ]
The driver should be deregistered as misc driver after PCI registration
failure.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20231015114529.10725-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4ca10f3e31 upstream.
The driver retries certain register reads 3 times if the returned value is
0. This was done because the controller could return 0 for certain
registers if other registers were being accessed concurrently by the BMC.
In certain systems with increased BMC interactions, the register values
returned can be 0 for longer than 3 retries. Change the retry count from 3
to 30 for the affected registers to prevent problems with out-of-band
management.
Fixes: b899202901 ("scsi: mpt3sas: Add separate function for aero doorbell reads")
Cc: stable@vger.kernel.org
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230829090020.5417-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d684a7a26f ]
_base_allocate_sense_dma_pool() already prints out the sense pool
information, so don't print it a second time after calling it in
_base_allocate_memory_pools(). In addition the version in
_base_allocate_memory_pools() was using the wrong size value, sz, which was
last assigned when doing some nvme calculations instead of sense_sz to
determine the pool size in kilobytes.
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Fixes: 970ac2bb70 ("scsi: mpt3sas: Force sense buffer allocations to be within same 4 GB region")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20230324193204.567932-1-jsnitsel@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c57724f1 ]
Port is allocated by sas_port_alloc_num() and rphy is allocated by either
sas_end_device_alloc() or sas_expander_alloc(), all of which may return
NULL. So we need to check the rphy to avoid possible NULL pointer access.
If sas_rphy_add() returned with failure, rphy is set to NULL. We would
access the rphy in the following lines which would also result NULL pointer
access.
Fixes: 78316e9dfc ("scsi: mpt3sas: Fix possible resource leaks in mpt3sas_transport_port_add()")
Signed-off-by: Wenchao Hao <haowenchao2@huawei.com>
Link: https://lore.kernel.org/r/20230225100135.2109330-1-haowenchao2@huawei.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 06e472acf9 upstream.
Remove the usage of dma_get_required_mask() API. Directly set the DMA mask
to 63/64 if the system is a 64bit machine.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20221028091655.17741-2-sreekanth.reddy@broadcom.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78316e9dfc ]
In mpt3sas_transport_port_add(), if sas_rphy_add() returns error,
sas_rphy_free() needs be called to free the resource allocated in
sas_end_device_alloc(). Otherwise a kernel crash will happen:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108
CPU: 45 PID: 37020 Comm: bash Kdump: loaded Tainted: G W 6.1.0-rc1+ #189
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x54/0x3d0
lr : device_del+0x37c/0x3d0
Call trace:
device_del+0x54/0x3d0
attribute_container_class_device_del+0x28/0x38
transport_remove_classdev+0x6c/0x80
attribute_container_device_trigger+0x108/0x110
transport_remove_device+0x28/0x38
sas_rphy_remove+0x50/0x78 [scsi_transport_sas]
sas_port_delete+0x30/0x148 [scsi_transport_sas]
do_sas_phy_delete+0x78/0x80 [scsi_transport_sas]
device_for_each_child+0x68/0xb0
sas_remove_children+0x30/0x50 [scsi_transport_sas]
sas_rphy_remove+0x38/0x78 [scsi_transport_sas]
sas_port_delete+0x30/0x148 [scsi_transport_sas]
do_sas_phy_delete+0x78/0x80 [scsi_transport_sas]
device_for_each_child+0x68/0xb0
sas_remove_children+0x30/0x50 [scsi_transport_sas]
sas_remove_host+0x20/0x38 [scsi_transport_sas]
scsih_remove+0xd8/0x420 [mpt3sas]
Because transport_add_device() is not called when sas_rphy_add() fails, the
device is not added. When sas_rphy_remove() is subsequently called to
remove the device in the remove() path, a NULL pointer dereference happens.
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221109032403.1636422-1-yangyingliang@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a re-do of commit e0e0747de0 ("scsi: mpt3sas: Fix return value
check of dma_get_required_mask()"), which I ended up undoing in a
mis-merge in commit 62e6e5940c ("Merge tag 'scsi-misc' of
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi").
The original commit message was
scsi: mpt3sas: Fix return value check of dma_get_required_mask()
Fix the incorrect return value check of dma_get_required_mask(). Due to
this incorrect check, the driver was always setting the DMA mask to 63 bit.
Link: https://lore.kernel.org/r/20220913120538.18759-2-sreekanth.reddy@broadcom.com
Fixes: ba27c5cf28 ("scsi: mpt3sas: Don't change the DMA coherent mask after allocations")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
and this fix was lost when I mis-merged the conflict with commit
9df650963b ("scsi: mpt3sas: Don't change DMA mask while reallocating
pools").
Reported-by: Juergen Gross <jgross@suse.com>
Fixes: 62e6e5940c ("Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi")
Link: https://lore.kernel.org/all/CAHk-=wjaK-TxrNaGtFDpL9qNHL1MVkWXO1TT6vObD5tXMSC4Zg@mail.gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target); the biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so. Beyond the usual bug fixing and
security class reworks, there aren't a huge number of core changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY0B74yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishW2NAP9CPp2R
7NRmSyxcyVYvtCNUW3WxXh65Gn+KgArmg8XucgEAhUBX1fSjOzpERWEU+UaXitbE
Rb+FbjxSc5YxR+nJ/Qc=
=0Wlp
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target). The biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so.
Beyond the usual bug fixing and security class reworks, there aren't a
huge number of core changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
scsi: mpi3mr: Remove unnecessary cast
scsi: stex: Properly zero out the passthrough command structure
scsi: mpi3mr: Update driver version to 8.2.0.3.0
scsi: mpi3mr: Fix scheduling while atomic type bug
scsi: mpi3mr: Scan the devices during resume time
scsi: mpi3mr: Free enclosure objects during driver unload
scsi: mpi3mr: Handle 0xF003 Fault Code
scsi: mpi3mr: Graceful handling of surprise removal of PCIe HBA
scsi: mpi3mr: Schedule IRQ kthreads only on non-RT kernels
scsi: mpi3mr: Support new power management framework
scsi: mpi3mr: Update mpi3 header files
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix ioc->base_readl() use"
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix writel() use"
scsi: wd33c93: Remove dead code related to the long-gone config WD33C93_PIO
scsi: core: Add I/O timeout count for SCSI device
scsi: qedf: Populate sysfs attributes for vport
scsi: pm8001: Replace one-element array with flexible-array member
scsi: 3w-xxxx: Replace one-element array with flexible-array member
scsi: hptiop: Replace one-element array with flexible-array member in struct hpt_iop_request_ioctl_command()
...
-----BEGIN PGP SIGNATURE-----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=R05e
-----END PGP SIGNATURE-----
Merge tag 'for-6.1/block-2022-10-03' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Christoph:
- handle number of queue changes in the TCP and RDMA drivers
(Daniel Wagner)
- allow changing the number of queues in nvmet (Daniel Wagner)
- also consider host_iface when checking ip options (Daniel
Wagner)
- don't map pages which can't come from HIGHMEM (Fabio M. De
Francesco)
- avoid unnecessary flush bios in nvmet (Guixin Liu)
- shrink and better pack the nvme_iod structure (Keith Busch)
- add comment for unaligned "fake" nqn (Linjun Bao)
- print actual source IP address through sysfs "address" attr
(Martin Belanger)
- various cleanups (Jackie Liu, Wolfram Sang, Genjian Zhang)
- handle effects after freeing the request (Keith Busch)
- copy firmware_rev on each init (Keith Busch)
- restrict management ioctls to admin (Keith Busch)
- ensure subsystem reset is single threaded (Keith Busch)
- report the actual number of tagset maps in nvme-pci (Keith
Busch)
- small fabrics authentication fixups (Christoph Hellwig)
- add common code for tagset allocation and freeing (Christoph
Hellwig)
- stop using the request_queue in nvmet (Christoph Hellwig)
- set min_align_mask before calculating max_hw_sectors (Rishabh
Bhatnagar)
- send a rediscover uevent when a persistent discovery controller
reconnects (Sagi Grimberg)
- misc nvmet-tcp fixes (Varun Prakash, zhenwei pi)
- MD pull request via Song:
- Various raid5 fix and clean up, by Logan Gunthorpe and David
Sloan.
- Raid10 performance optimization, by Yu Kuai.
- sbitmap wakeup hang fixes (Hugh, Keith, Jan, Yu)
- IO scheduler switching quisce fix (Keith)
- s390/dasd block driver updates (Stefan)
- support for recovery for the ublk driver (ZiyangZhang)
- rnbd drivers fixes and updates (Guoqing, Santosh, ye, Christoph)
- blk-mq and null_blk map fixes (Bart)
- various bcache fixes (Coly, Jilin, Jules)
- nbd signal hang fix (Shigeru)
- block writeback throttling fix (Yu)
- optimize the passthrough mapping handling (me)
- prepare block cgroups to being gendisk based (Christoph)
- get rid of an old PSI hack in the block layer, moving it to the
callers instead where it belongs (Christoph)
- blk-throttle fixes and cleanups (Yu)
- misc fixes and cleanups (Liu Shixin, Liu Song, Miaohe, Pankaj,
Ping-Xiang, Wolfram, Saurabh, Li Jinlin, Li Lei, Lin, Li zeming,
Miaohe, Bart, Coly, Gaosheng
* tag 'for-6.1/block-2022-10-03' of git://git.kernel.dk/linux: (162 commits)
sbitmap: fix lockup while swapping
block: add rationale for not using blk_mq_plug() when applicable
block: adapt blk_mq_plug() to not plug for writes that require a zone lock
s390/dasd: use blk_mq_alloc_disk
blk-cgroup: don't update the blkg lookup hint in blkg_conf_prep
nvmet: don't look at the request_queue in nvmet_bdev_set_limits
nvmet: don't look at the request_queue in nvmet_bdev_zone_mgmt_emulate_all
blk-mq: use quiesced elevator switch when reinitializing queues
block: replace blk_queue_nowait with bdev_nowait
nvme: remove nvme_ctrl_init_connect_q
nvme-loop: use the tagset alloc/free helpers
nvme-loop: store the generic nvme_ctrl in set->driver_data
nvme-loop: initialize sqsize later
nvme-fc: use the tagset alloc/free helpers
nvme-fc: store the generic nvme_ctrl in set->driver_data
nvme-fc: keep ctrl->sqsize in sync with opts->queue_size
nvme-rdma: use the tagset alloc/free helpers
nvme-rdma: store the generic nvme_ctrl in set->driver_data
nvme-tcp: use the tagset alloc/free helpers
nvme-tcp: store the generic nvme_ctrl in set->driver_data
...
Fix the incorrect return value check of dma_get_required_mask(). Due to
this incorrect check, the driver was always setting the DMA mask to 63 bit.
Link: https://lore.kernel.org/r/20220913120538.18759-2-sreekanth.reddy@broadcom.com
Fixes: ba27c5cf28 ("scsi: mpt3sas: Don't change the DMA coherent mask after allocations")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following use-after-free warning which is observed during
controller reset:
refcount_t: underflow; use-after-free.
WARNING: CPU: 23 PID: 5399 at lib/refcount.c:28 refcount_warn_saturate+0xa6/0xf0
Link: https://lore.kernel.org/r/20220906134908.1039-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With cmd_per_lun value 7, a higher number of cache lines (map_nr) are
needed while allocating sdev->budget_map which is not reasonable and hence
increase the cmd_per_lun value to 128.
Link: https://lore.kernel.org/r/20220825075457.16422-4-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ExtendedType field was set to 1 in the diag buffer register command and
hence MPT Endpoint firmware is failing the request with Invalid Field
IOCStatus.
memset the request frame to zero before framing the diag buffer register
command.
Link: https://lore.kernel.org/r/20220825075457.16422-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a pool crosses the 4GB boundary region then before reallocating pools
change the coherent DMA mask to 32 bits and keep the normal DMA mask set to
63/64 bits.
Link: https://lore.kernel.org/r/20220825075457.16422-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SCSI error handling is taking place for timed out I/Os on a drive and
the corresponding drive is removed, then stop escalating to higher level of
reset by returning the TUR with "I_T NEXUS LOSS OCCURRED" sense key.
Link: https://lore.kernel.org/r/20220816080801.13929-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disable firmware download for ATTO devices where it is not supported.
Link: https://lore.kernel.org/r/20220805174609.14830-2-bgrove@attotech.com
Co-developed-by: Rob Crispo <rcrispo@attotech.com>
Signed-off-by: Rob Crispo <rcrispo@attotech.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add ATTO's PCI IDs and modify the driver to handle the unique NVRAM
structure used by ATTO's devices.
Link: https://lore.kernel.org/r/20220805174609.14830-1-bgrove@attotech.com
Co-developed-by: Rob Crispo <rcrispo@attotech.com>
Signed-off-by: Rob Crispo <rcrispo@attotech.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since blk_mq_map_queues() and the .map_queues() callbacks always return 0,
change their return type into void. Most callers ignore the returned value
anyway.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Acked-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20220815170043.19489-3-bvanassche@acm.org
[axboe: fold in fix from Bart]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr). The main driver change that might cause issues on down the
road is the conversion of some of our oldest surviving drivers to the
DMA API (should only affect m68k). The only major core change is the
rework of async resume; the rest are either completely trivial or for
updating deprecated APIs.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYuvakyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfvOAP4m0N6b
e3JwoBtB1c0JMKv6G4gka8suEG8p5f4khDu8wwD+LfGUCzG49Y5Ts7rByXfEiGgO
krSdwsAZiV6yKg/HuPw=
=Ak9L
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr).
The main driver change that might cause issues on down the road is the
conversion of some of our oldest surviving drivers to the DMA API
(should only affect m68k).
The only major core change is the rework of async resume; the rest are
either completely trivial or for updating deprecated APIs"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (195 commits)
scsi: target: Remove XDWRITEREAD emulated support
scsi: megaraid: Remove the static variable initialisation
scsi: ch: Do not initialise statics to 0
scsi: ufs: core: Fix spelling mistake "Cannnot" -> "Cannot"
scsi: target: iscsi: Do not require target authentication
scsi: target: iscsi: Allow AuthMethod=None
scsi: target: iscsi: Support base64 in CHAP
scsi: target: iscsi: Add support for extended CDB AHS
scsi: ufs: dt-bindings: Add SC8280XP binding
scsi: target: iscsi: Fix clang -Wformat warnings
scsi: ufs: core: Read device property for ref clock
scsi: libsas: Resume SAS host for phy reset or enable via sysfs
scsi: hisi_sas: Modify v3 HW SATA completion error processing
scsi: hisi_sas: Relocate DMA unmap of SMP task
scsi: hisi_sas: Remove unnecessary variable to hold DMA map elements
scsi: hisi_sas: Call hisi_sas_slave_configure() from slave_configure_v3_hw()
scsi: mpi3mr: Delete a stray tab
scsi: mpi3mr: Unlock on error path
scsi: mpi3mr: Reduce VD queue depth on detecting throttling
scsi: mpi3mr: Resource Based Metering
...
During system shutdown or reboot, mpt3sas will reset the firmware back to
ready state. However, the driver leaves running a watchdog work item
intended to keep the firmware in operational state. This causes a second,
unneeded reset on shutdown and moves the firmware back to operational
instead of in ready state as intended. And if the mpt3sas_fwfault_debug
module parameter is set, this extra reset also panics the system.
mpt3sas's scsih_shutdown needs to stop the watchdog before resetting the
firmware back to ready state.
Link: https://lore.kernel.org/r/20220722142448.6289-1-djeffery@redhat.com
Fixes: fae21608c3 ("scsi: mpt3sas: Transition IOC to Ready state during shutdown")
Tested-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It seems to me that mpt3sas driver is using dedicated workqueues and is not
calling schedule{,_delayed}_work{,_on}(). Then, there will be no work to
flush using flush_scheduled_work().
Link: https://lore.kernel.org/r/f3b97c7c-1094-4e46-20d8-4321716d6f3f@I-love.SAKURA.ne.jp
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in _base_sas_ioc_info(). Change 'cant' to
'can't'.
Also fix up whitespace.
Link: https://lore.kernel.org/r/20220617101103.3162-1-jiaming@nfschina.com
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I'm facing this warning when building for the parisc64 architecture:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function ‘_base_make_ioc_operational’:
drivers/scsi/mpt3sas/mpt3sas_base.c:5396:40: warning: array subscript ‘Mpi2SasIOUnitPage1_t {aka struct _MPI2_CONFIG_PAGE_SASIOUNIT_1}[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds]
5396 | (le16_to_cpu(sas_iounit_pg1->SASWideMaxQueueDepth)) ?
drivers/scsi/mpt3sas/mpt3sas_base.c:5382:26: note: referencing an object of size 20 allocated by ‘kzalloc’
5382 | sas_iounit_pg1 = kzalloc(sz, GFP_KERNEL);
| ^~~~~~~~~~~~~~~~~~~~~~~
The problem is, that only 20 bytes are allocated with kmalloc(), which is
sufficient to hold the bytes which are needed. Nevertheless, gcc complains
because the whole Mpi2SasIOUnitPage1_t struct is 32 bytes in size and thus
doesn't fit into those 20 bytes.
This patch simply allocates all 32 bytes (instead of 20) and thus avoids
the warning. There is no functional change introduced by this patch.
While touching the code I cleaned up to calculation of max_wideport_qd,
max_narrowport_qd and max_sata_qd to make it easier readable.
Test successfully tested on a HP C8000 PA-RISC workstation with 64-bit
kernel.
Link: https://lore.kernel.org/r/YpZ197iZdDZSCzrT@p100
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Terminate string after copying 16 bytes of ChipName data from Manufacturing
Page0 to prevent %s from printing junk characters.
Link: https://lore.kernel.org/r/20220511072621.30657-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We now cache VPD page 0x89 (ATA Information) so there is no need to request
it from the hardware. Make mpt3sas use the cached page.
Link: https://lore.kernel.org/r/20220302053559.32147-2-martin.petersen@oracle.com
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The replyPostRegisterIndex array of struct MPT3SAS_ADAPTER stores iomem
resource addresses. Fix its declaration to annotate it with __iomem to
avoid sparse warnings for writel() calls using the stored addresses.
Link: https://lore.kernel.org/r/20220307234854.148145-6-damien.lemoal@opensource.wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In mpt3sas_scsih_event_callback(), fix a sparse warning when testing the
event log code value by replacing the use of a pointer to the address
storing the event log code with a log code local variable. Doing so,
le32_to_cpu() is used when the log code value is assigned, avoiding a
sparse warning.
Link: https://lore.kernel.org/r/20220307234854.148145-5-damien.lemoal@opensource.wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The functions _base_readl_aero() and _base_readl() used for an adapter
base_readl() method are implemented using a regular readl() call which
internally performs a conversion to CPU endianness (le32_to_cpu()) of
the values read. The users of the ioc base_readl() method should thus
not convert again the values read using le16_to_cpu().
Fixing this removes sparse warnings.
Link: https://lore.kernel.org/r/20220307234854.148145-4-damien.lemoal@opensource.wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
writel() internally executes cpu_to_le32() to convert the value being
written to little endian. The caller should thus not use this conversion
function for the value passed to writel(). Remove the cpu_to_le32() calls
in _base_put_smid_scsi_io_atomic(), _base_put_smid_fast_path_atomic(),
_base_put_smid_hi_priority_atomic() _base_put_smid_default_atomic() and
_base_handshake_req_reply_wait().
Link: https://lore.kernel.org/r/20220307234854.148145-3-damien.lemoal@opensource.wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The TaskMID field of struct Mpi2SCSITaskManagementRequest_t is a 16-bit
little endian value. Fix the search loop in _ctl_set_task_mid() to add a
cpu_to_le16() conversion before checking the value of TaskMID to avoid
sparse warnings. While at it, simplify the search loop code to remove an
unnecessarily complicated if condition.
Link: https://lore.kernel.org/r/20220307234854.148145-2-damien.lemoal@opensource.wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of controller reset operation the driver issues a config request
command. If this command gets times out, then fail the controller reset
operation instead of retrying it.
Link: https://lore.kernel.org/r/20220405120637.20528-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The start_addres argument of mpt3sas_check_same_4gb_region() was misnamed
in the function kdoc comment, resulting in the following warning when
compiling with W=1.
drivers/scsi/mpt3sas/mpt3sas_base.c:5728: warning: Function parameter or
member 'start_address' not described in 'mpt3sas_check_same_4gb_region'
drivers/scsi/mpt3sas/mpt3sas_base.c:5728: warning: Excess function
parameter 'reply_pool_start_address' description in
'mpt3sas_check_same_4gb_region'
Fix the argument name in the function kdoc comment to avoid it. While at
it, remove a useless blank line between the kdoc and function code.
Link: https://lore.kernel.org/r/20220404050041.594774-1-damien.lemoal@opensource.wdc.com
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function mpt3sas_transport_port_remove() called in
_scsih_expander_node_remove() frees the port field of the sas_expander
structure, leading to the following use-after-free splat from KASAN when
the ioc_info() call following that function is executed (e.g. when doing
rmmod of the driver module):
[ 3479.371167] ==================================================================
[ 3479.378496] BUG: KASAN: use-after-free in _scsih_expander_node_remove+0x710/0x750 [mpt3sas]
[ 3479.386936] Read of size 1 at addr ffff8881c037691c by task rmmod/1531
[ 3479.393524]
[ 3479.395035] CPU: 18 PID: 1531 Comm: rmmod Not tainted 5.17.0-rc8+ #1436
[ 3479.401712] Hardware name: Supermicro Super Server/H12SSL-NT, BIOS 2.1 06/02/2021
[ 3479.409263] Call Trace:
[ 3479.411743] <TASK>
[ 3479.413875] dump_stack_lvl+0x45/0x59
[ 3479.417582] print_address_description.constprop.0+0x1f/0x120
[ 3479.423389] ? _scsih_expander_node_remove+0x710/0x750 [mpt3sas]
[ 3479.429469] kasan_report.cold+0x83/0xdf
[ 3479.433438] ? _scsih_expander_node_remove+0x710/0x750 [mpt3sas]
[ 3479.439514] _scsih_expander_node_remove+0x710/0x750 [mpt3sas]
[ 3479.445411] ? _raw_spin_unlock_irqrestore+0x2d/0x40
[ 3479.452032] scsih_remove+0x525/0xc90 [mpt3sas]
[ 3479.458212] ? mpt3sas_expander_remove+0x1d0/0x1d0 [mpt3sas]
[ 3479.465529] ? down_write+0xde/0x150
[ 3479.470746] ? up_write+0x14d/0x460
[ 3479.475840] ? kernfs_find_ns+0x137/0x310
[ 3479.481438] pci_device_remove+0x65/0x110
[ 3479.487013] __device_release_driver+0x316/0x680
[ 3479.493180] driver_detach+0x1ec/0x2d0
[ 3479.498499] bus_remove_driver+0xe7/0x2d0
[ 3479.504081] pci_unregister_driver+0x26/0x250
[ 3479.510033] _mpt3sas_exit+0x2b/0x6cf [mpt3sas]
[ 3479.516144] __x64_sys_delete_module+0x2fd/0x510
[ 3479.522315] ? free_module+0xaa0/0xaa0
[ 3479.527593] ? __cond_resched+0x1c/0x90
[ 3479.532951] ? lockdep_hardirqs_on_prepare+0x273/0x3e0
[ 3479.539607] ? syscall_enter_from_user_mode+0x21/0x70
[ 3479.546161] ? trace_hardirqs_on+0x1c/0x110
[ 3479.551828] do_syscall_64+0x35/0x80
[ 3479.556884] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 3479.563402] RIP: 0033:0x7f1fc482483b
...
[ 3479.943087] ==================================================================
Fix this by introducing the local variable port_id to store the port ID
value before executing mpt3sas_transport_port_remove(). This local variable
is then used in the call to ioc_info() instead of dereferencing the freed
port structure.
Link: https://lore.kernel.org/r/20220322055702.95276-1-damien.lemoal@opensource.wdc.com
Fixes: 7d310f2410 ("scsi: mpt3sas: Get device objects using sas_address & portID")
Cc: stable@vger.kernel.org
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes. The high blast radius core update is the removal of
write same, which affects block and several non-SCSI devices. The
other big change, which is more local, is the removal of the SCSI
pointer.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYjzDQyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQMYAQDEWUGV
6U0+736AHVtOfiMNfiRN79B1HfXVoHvemnPcTwD/UlndwFfy/3GGOtoZmqEpc73J
Ec1HDuUCE18H1H2QAh0=
=/Ty9
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes.
The high blast radius core update is the removal of write same, which
affects block and several non-SCSI devices. The other big change,
which is more local, is the removal of the SCSI pointer"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (281 commits)
scsi: scsi_ioctl: Drop needless assignment in sg_io()
scsi: bsg: Drop needless assignment in scsi_bsg_sg_io_fn()
scsi: lpfc: Copyright updates for 14.2.0.0 patches
scsi: lpfc: Update lpfc version to 14.2.0.0
scsi: lpfc: SLI path split: Refactor BSG paths
scsi: lpfc: SLI path split: Refactor Abort paths
scsi: lpfc: SLI path split: Refactor SCSI paths
scsi: lpfc: SLI path split: Refactor CT paths
scsi: lpfc: SLI path split: Refactor misc ELS paths
scsi: lpfc: SLI path split: Refactor VMID paths
scsi: lpfc: SLI path split: Refactor FDISC paths
scsi: lpfc: SLI path split: Refactor LS_RJT paths
scsi: lpfc: SLI path split: Refactor LS_ACC paths
scsi: lpfc: SLI path split: Refactor the RSCN/SCR/RDF/EDC/FARPR paths
scsi: lpfc: SLI path split: Refactor PLOGI/PRLI/ADISC/LOGO paths
scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path
scsi: lpfc: SLI path split: Introduce lpfc_prep_wqe
scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
scsi: lpfc: SLI path split: Refactor lpfc_iocbq
scsi: lpfc: Use kcalloc()
...
