commit e66b0a8f04 upstream.
Using of_property_read_bool() for non-boolean properties is deprecated
and results in a warning during runtime since commit c141ecc3ce ("of:
Warn when of_property_read_bool() is used on non-boolean properties").
Fixes: b6ef830c60 ("i2c: omap: Add support for setting mux")
Cc: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250415075230.16235-1-johan+linaro@kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ef830c60 upstream.
Some SoCs require muxes in the routing for SDA and SCL lines.
Therefore, add support for setting the mux by reading the mux-states
property from the dt-node.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20250318103622.29979-3-j-choudhary@ti.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: a9503a2ecd ("i2c: omap: Handle omap_i2c_init() errors in omap_i2c_probe()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c870cbbd71 upstream.
If the DMA mapping failed, it produced an error log with the wrong
device name:
"stm32-dma3 40400000.dma-controller: rejecting DMA map of vmalloc memory"
Fix this issue by replacing the dev with the I2C dev.
Fixes: bb8822cbbc ("i2c: i2c-stm32: Add generic DMA API")
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Cc: <stable@vger.kernel.org> # v4.18+
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250704-i2c-upstream-v4-1-84a095a2c728@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d30048958 upstream.
The i2c_dw_xfer_init() function requires msgs and msg_write_idx from the
dev context to be initialized.
amd_i2c_dw_xfer_quirk() inits msgs and msgs_num, but not msg_write_idx.
This could allow an out of bounds access (of msgs).
Initialize msg_write_idx before calling i2c_dw_xfer_init().
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 17631e8ca2 ("i2c: designware: Add driver support for AMD NAVI GPU")
Cc: <stable@vger.kernel.org> # v5.13+
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250627143511.489570-1-michael.j.ruhl@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56ad91c1aa upstream.
This driver passes the length of an i2c_msg directly to
usb_control_msg(). If the message is now a read and of length 0, it
violates the USB protocol and a warning will be printed. Enable the
I2C_AQ_NO_ZERO_LEN_READ quirk for this adapter thus forbidding 0-length
read messages altogether.
Fixes: 83e53a8f12 ("i2c: Add bus driver for for OSIF USB i2c device.")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250522064234.3721-2-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbdb25ccf7 upstream.
This driver passes the length of an i2c_msg directly to
usb_control_msg(). If the message is now a read and of length 0, it
violates the USB protocol and a warning will be printed. Enable the
I2C_AQ_NO_ZERO_LEN_READ quirk for this adapter thus forbidding 0-length
read messages altogether.
Fixes: e8c76eed2e ("i2c: New i2c-tiny-usb bus driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # v2.6.22+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250522064349.3823-2-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38010591a0 ]
During init of the bus, the module checks that the bus is idle.
If one of the lines are stuck try to recover them first before failing.
Sometimes SDA and SCL are low if improper reset occurs (e.g., reboot).
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Mohammed Elbadry <mohammed.0.elbadry@gmail.com>
Reviewed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250328193252.1570811-1-mohammed.0.elbadry@gmail.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6e04f05ce ]
For SMBUS block read, do not continue to read if the message length
passed from the device is '0' or greater than the maximum allowed bytes.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250424053320.19211-1-akhilrajeev@nvidia.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fe2b969d9 ]
Replaced pm_runtime_put() with pm_runtime_put_sync_suspend() to ensure
the runtime suspend is invoked immediately when unregistering a slave.
This prevents a race condition where suspend was skipped when
unregistering and registering slave in quick succession.
For example, consider the rapid sequence of
`delete_device -> new_device -> delete_device -> new_device`.
In this sequence, it is observed that the dw_i2c_plat_runtime_suspend()
might not be invoked after `delete_device` operation.
This is because after `delete_device` operation, when the
pm_runtime_put() is about to trigger suspend, the following `new_device`
operation might race and cancel the suspend.
If that happens, during the `new_device` operation,
dw_i2c_plat_runtime_resume() is skipped (since there was no suspend), which
means `i_dev->init()`, i.e. i2c_dw_init_slave(), is skipped.
Since i2c_dw_init_slave() is skipped, i2c_dw_configure_fifo_slave() is
skipped too, which leaves `DW_IC_INTR_MASK` unconfigured. If we inspect
the interrupt mask register using devmem, it will show as zero.
Example shell script to reproduce the issue:
```
#!/bin/sh
SLAVE_LADDR=0x1010
SLAVE_BUS=13
NEW_DEVICE=/sys/bus/i2c/devices/i2c-$SLAVE_BUS/new_device
DELETE_DEVICE=/sys/bus/i2c/devices/i2c-$SLAVE_BUS/delete_device
# Create initial device
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
sleep 2
# Rapid sequence of
# delete_device -> new_device -> delete_device -> new_device
echo $SLAVE_LADDR > $DELETE_DEVICE
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
echo $SLAVE_LADDR > $DELETE_DEVICE
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
# Using devmem to inspect IC_INTR_MASK will show as zero
```
Signed-off-by: Tan En De <ende.tan@starfivetech.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250412023303.378600-1-ende.tan@starfivetech.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be7113d2e2 ]
If the clock i2c->clk was not enabled in i2c_pxa_probe(), it should not be
disabled in any path.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250212172803.1422136-1-mordan@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4f35233a6 ]
When the I2C QUP controller is used together with a DMA engine it needs
to vote for the interconnect path to the DRAM. Otherwise it may be
unable to access the memory quickly enough.
The requested peak bandwidth is dependent on the I2C core clock.
To avoid sending votes too often the bandwidth is always requested when
a DMA transfer starts, but dropped only on runtime suspend. Runtime
suspend should only happen if no transfer is active. After resumption we
can defer the next vote until the first DMA transfer actually happens.
The implementation is largely identical to the one introduced for
spi-qup in commit ecdaa94730 ("spi: qup: Vote for interconnect
bandwidth to DRAM") since both drivers represent the same hardware
block.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20231128-i2c-qup-dvfs-v1-3-59a0e3039111@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cfe51ef07 ]
If navi_amd_register_client() fails, the previous i2c_dw_probe() call
should be undone by a corresponding i2c_del_adapter() call, as already done
in the remove function.
Fixes: 17631e8ca2 ("i2c: designware: Add driver support for AMD NAVI GPU")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <stable@vger.kernel.org> # v5.13+
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/fcd9651835a32979df8802b2db9504c523a8ebbb.1747158983.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc07fb4170 ]
Commit 90312351fd ("i2c: designware: MASTER mode as separated driver")
introduced ->disable() callback but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable() and scope is inside the same kernel module.
That said, replace the callback by explicitly calling the i2c_dw_disable().
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: 1cfe51ef07 ("i2c: designware: Fix an error handling path in i2c_dw_pci_probe()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 535677e44d ]
Currently initialization flow in i2c_dw_probe_master() skips a few steps
and has code duplication for polling mode implementation.
Simplify this by adding a new ACCESS_POLLING flag that is set for those
two platforms that currently use polling mode and use it to skip
interrupt handler setup.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: 1cfe51ef07 ("i2c: designware: Fix an error handling path in i2c_dw_pci_probe()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 285df995f9 upstream.
On the GTA04A5 writing a reset command to the gyroscope causes IRQ
storms because NACK IRQs are enabled and therefore triggered but not
acked.
Sending a reset command to the gyroscope by
i2cset 1 0x69 0x14 0xb6
with an additional debug print in the ISR (not the thread) itself
causes
[ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00
[ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1
[ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110)
[ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010)
[ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
repeating till infinity
[...]
(0x2 = NACK, 0x100 = Bus free, which is not enabled)
Apparently no other IRQ bit gets set, so this stalls.
Do not ignore enabled interrupts and make sure they are acked.
If the NACK IRQ is not needed, it should simply not enabled, but
according to the above log, caring about it is necessary unless
the Bus free IRQ is enabled and handled. The assumption that is
will always come with a ARDY IRQ, which was the idea behind
ignoring it, proves wrong.
It is true for simple reads from an unused address.
To still avoid the i2cdetect trouble which is the reason for
commit c770657bd2 ("i2c: omap: Fix standard mode false ACK readings"),
avoid doing much about NACK in omap_i2c_xfer_data() which is used
by both IRQ mode and polling mode, so also the false detection fix
is extended to polling usage and IRQ storms are avoided.
By changing this, the hardirq handler is not needed anymore to filter
stuff.
The mentioned gyro reset now just causes a -ETIMEDOUT instead of
hanging the system.
Fixes: c770657bd2 ("i2c: omap: Fix standard mode false ACK readings").
CC: stable@kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71c49ee9bb upstream.
According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Fixes: 015e61f0bf ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: stable@vger.kernel.org # v6.3+
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220125612.1910990-1-zhoubinbin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 093f70c134 ]
When this controller is a target, the NACK handling had two issues.
First, the return value from the backend was not checked on the initial
WRITE_REQUESTED. So, the driver missed to send a NACK in this case.
Also, the NACK always arrives one byte late on the bus, even in the
WRITE_RECEIVED case. This seems to be a HW issue. We should then not
rely on the backend to correctly NACK the superfluous byte as well. Fix
both issues by introducing a flag which gets set whenever the backend
requests a NACK and keep sending it until we get a STOP condition.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 89a4ad1f43 upstream.
Use the newly defined common and generic PCC shared memory region
related macros in this driver to replace the locally defined ones.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20230927-pcc_defines-v2-2-0b8ffeaef2e5@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Stable-dep-of: 7f9e19f207 ("mailbox: pcc: Check before sending MCTP PCC response ACK")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49e1f0fd0d upstream.
Running i2c-detect currently produces an output akin to:
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: 08 -- 0a -- 0c -- 0e --
10: 10 -- 12 -- 14 -- 16 -- UU 19 -- 1b -- 1d -- 1f
20: -- 21 -- 23 -- 25 -- 27 -- 29 -- 2b -- 2d -- 2f
30: -- -- -- -- -- -- -- -- 38 -- 3a -- 3c -- 3e --
40: 40 -- 42 -- 44 -- 46 -- 48 -- 4a -- 4c -- 4e --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: 60 -- 62 -- 64 -- 66 -- 68 -- 6a -- 6c -- 6e --
70: 70 -- 72 -- 74 -- 76 --
This happens because for an i2c_msg with a len of 0 the driver will
mark the transmission of the message as a success once the START has
been sent, without waiting for the devices on the bus to respond with an
ACK/NAK. Since i2cdetect seems to run in a tight loop over all addresses
the NAK is treated as part of the next test for the next address.
Delete the fast path that marks a message as complete when idev->msg_len
is zero after sending a START/RESTART since this isn't a valid scenario.
CC: stable@vger.kernel.org
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241218-outbid-encounter-b2e78b1cc707@spud
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0cec36319 upstream.
Compatible string "fsl,imx7d-i2c" is not exited at i2c-imx driver
compatible string table, at the result, "fsl,imx21-i2c" will be
matched, but it will cause erratum ERR007805 not be applied in fact.
So Add "fsl,imx7d-i2c" compatible string in i2c-imx driver to apply
the erratum ERR007805(https://www.nxp.com/docs/en/errata/IMX7DS_3N09P.pdf).
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
"fsl,imx7d-i2c" already is documented in binding doc. This erratum
fix has been included in imx6_i2c_hwdata and it is the same in all
I.MX6/7/8, so just reuse it.
Fixes: 39c025721d ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Fixes: 39c025721d ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit")
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20241218044238.143414-1-carlos.song@nxp.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a8f9320d6 upstream.
At present, where repeated sends are intended to be used, the
i2c-microchip-core driver sends a stop followed by a start. Lots of i2c
devices must not malfunction in the face of this behaviour, because the
driver has operated like this for years! Try to keep track of whether or
not a repeated send is required, and suppress sending a stop in these
cases.
CC: stable@vger.kernel.org
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241218-football-composure-e56df2461461@spud
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de6b43798d upstream.
Currently, the RIIC driver may run the I2C bus faster than requested,
which may cause subtle failures. E.g. Biju reported a measured bus
speed of 450 kHz instead of the expected maximum of 400 kHz on RZ/G2L.
The initial calculation of the bus period uses DIV_ROUND_UP(), to make
sure the actual bus speed never becomes faster than the requested bus
speed. However, the subsequent division-by-two steps do not use
round-up, which may lead to a too-small period, hence a too-fast and
possible out-of-spec bus speed. E.g. on RZ/Five, requesting a bus speed
of 100 resp. 400 kHz will yield too-fast target bus speeds of 100806
resp. 403226 Hz instead of 97656 resp. 390625 Hz.
Fix this by using DIV_ROUND_UP() in the subsequent divisions, too.
Tested on RZ/A1H, RZ/A2M, and RZ/Five.
Fixes: d982d66514 ("i2c: riic: remove clock and frequency restrictions")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://lore.kernel.org/r/c59aea77998dfea1b4456c4b33b55ab216fcbf5e.1732284746.git.geert+renesas@glider.be
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7363f2d4c1 ]
Since commit f63b94be69 ("i2c: pnx: Fix potential deadlock warning
from del_timer_sync() call in isr") jiffies are stored in
i2c_pnx_algo_data.timeout, but wait_timeout and wait_reset are still
using it as milliseconds. Convert jiffies back to milliseconds to wait
for the expected amount of time.
Fixes: f63b94be69 ("i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr")
Signed-off-by: Vladimir Riabchun <ferr.lambarginio@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4268254a39 ]
Instead of repeatedly calling clk_get_rate for each transfer, lock
the clock rate and cache the value.
A deadlock has been observed while adding tlv320aic32x4 audio codec to
the system. When this clock provider adds its clock, the clk mutex is
locked already, it needs to access i2c, which in return needs the mutex
for clk_get_rate as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
[ Resolve minor conflicts to fix CVE-2024-40965 ]
Signed-off-by: Bin Lan <bin.lan.cn@windriver.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8de3e97f3d upstream.
When the Tx FIFO is empty and the last command has no STOP bit
set, the master holds SCL low. If I2C_DYNAMIC_TAR_UPDATE is not
set, BIT(13) MST_ON_HOLD of IC_RAW_INTR_STAT is not enabled,
causing the __i2c_dw_disable() timeout. This is quite similar to
commit 2409205acd ("i2c: designware: fix __i2c_dw_disable() in
case master is holding SCL low"). Also check BIT(7)
MST_HOLD_TX_FIFO_EMPTY in IC_STATUS, which is available when
IC_STAT_FOR_CLK_STRETCH is set.
Fixes: 2409205acd ("i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low")
Co-developed-by: Xiaowu Ding <xiaowu.ding@jaguarmicro.com>
Signed-off-by: Xiaowu Ding <xiaowu.ding@jaguarmicro.com>
Co-developed-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: Liu Peibao <loven.liu@jaguarmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43457ada98 ]
On chipsets with a second 'Integrated Device Function' SMBus controller use
a different adapter-name for the second IDF adapter.
This allows platform glue code which is looking for the primary i801
adapter to manually instantiate i2c_clients on to differentiate
between the 2.
This allows such code to find the primary i801 adapter by name, without
needing to duplicate the PCI-ids to feature-flags mapping from i2c-i801.c.
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6722ea6b9 ]
'pclk' is only used locally in the probe. Remove it from the
'synquacer_i2c' structure.
Also remove a useless debug message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: f2990f8630 ("i2c: synquacer: Deal with optional PCLK correctly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5d69d5a00f upstream.
It was observed that issuing the ABORT bit (IC_ENABLE[1]) will not
work when IC_ENABLE is already disabled.
Check if the ENABLE bit (IC_ENABLE[0]) is disabled when the controller
is holding SCL low. If the ENABLE bit is disabled, the software needs
to enable it before trying to issue the ABORT bit. otherwise,
the controller ignores any write to ABORT bit.
These kernel logs show up whenever an I2C transaction is
attempted after this failure.
i2c_designware e95e0000.i2c: timeout waiting for bus ready
i2c_designware e95e0000.i2c: timeout in disabling adapter
The patch fixes the issue where the controller cannot be disabled
while SCL is held low if the ENABLE bit is already disabled.
Fixes: 2409205acd ("i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low")
Signed-off-by: Kimriver Liu <kimriver.liu@siengine.com>
Cc: <stable@vger.kernel.org> # v6.6+
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c8d604dea upstream.
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: 36ecbcab84 ("i2c: xiic: Implement power management")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 521da1e922 upstream.
Frequently an I2C write will be followed by a read, such as a register
address write followed by a read of the register value. In this driver,
when the TX FIFO half empty interrupt was raised and it was determined
that there was enough space in the TX FIFO to send the following read
command, it would do so without waiting for the TX FIFO to actually
empty.
Unfortunately it appears that in some cases this can result in a NAK
that was raised by the target device on the write, such as due to an
unsupported register address, being ignored and the subsequent read
being done anyway. This can potentially put the I2C bus into an
invalid state and/or result in invalid read data being processed.
To avoid this, once a message has been fully written to the TX FIFO,
wait for the TX FIFO empty interrupt before moving on to the next
message, to ensure NAKs are handled properly.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Cc: <stable@vger.kernel.org> # v2.6.34+
Reviewed-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2c85d85a0 upstream.
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Cc: <stable@vger.kernel.org> # v4.19+
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 048bbbdbf8 upstream.
In case there is any sort of clock controller attached to this I2C bus
controller, for example Versaclock or even an AIC32x4 I2C codec, then
an I2C transfer triggered from the clock controller clk_ops .prepare
callback may trigger a deadlock on drivers/clk/clk.c prepare_lock mutex.
This is because the clock controller first grabs the prepare_lock mutex
and then performs the prepare operation, including its I2C access. The
I2C access resumes this I2C bus controller via .runtime_resume callback,
which calls clk_prepare_enable(), which attempts to grab the prepare_lock
mutex again and deadlocks.
Since the clock are already prepared since probe() and unprepared in
remove(), use simple clk_enable()/clk_disable() calls to enable and
disable the clock on runtime suspend and resume, to avoid hitting the
prepare_lock mutex.
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 4e7bca6fc0 ("i2c: i2c-stm32f7: add PM Runtime support")
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d4a1adbed ]
In the event that the I2C bus was powered down when the I2C controller
driver loads, or some spurious pulses occur on the I2C bus, it's
possible that the controller detects a spurious I2C "start" condition.
In this situation it may continue to report the bus is busy indefinitely
and block the controller from working.
The "single-master" DT flag can be specified to disable bus busy checks
entirely, but this may not be safe to use in situations where other I2C
masters may potentially exist.
In the event that the controller reports "bus busy" for too long when
starting a transaction, we can try reinitializing the controller to see
if the busy condition clears. This allows recovering from this scenario.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Cc: <stable@vger.kernel.org> # v2.6.34+
Reviewed-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee1691d0ae ]
xiic_start_xfer can fail for different reasons:
- EBUSY: bus is busy or i2c messages still in tx_msg or rx_msg
- ETIMEDOUT: timed-out trying to clear the RX fifo
- EINVAL: wrong clock settings
Both EINVAL and ETIMEDOUT will currently print a specific error
message followed by a generic one, for example:
Failed to clear rx fifo
Error xiic_start_xfer
however EBUSY will simply output the generic message:
Error xiic_start_xfer
which is not really helpful.
This commit adds a new error message when a busy condition is detected
and also removes the generic message since it does not provide any
relevant information to the user.
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: 1d4a1adbed ("i2c: xiic: Try re-initialization on bus busy timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1db4da5507 upstream.
In accordance with the existing comment and code analysis
it is quite likely that there is a missed 'else' when adapter
times out. Add it.
Fixes: 5bc1200852 ("i2c: Add Intel SCH SMBus support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93701d3b84 upstream.
When the i2c bus recovery occurs, driver will send i2c stop command
in the scl low condition. In this case the sw state will still keep
original situation. Under multi-master usage, i2c bus recovery will
be called when i2c transfer timeout occurs. Update the stop command
calling with aspeed_i2c_do_stop function to update master_state.
Fixes: f327c686d3 ("i2c: aspeed: added driver for Aspeed I2C")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 470a662688 upstream.
Add an atomic_xfer method to the driver so that it behaves correctly
when controlling a PMIC that is responsible for device shutdown.
The atomic_xfer method added is similar to the one from the i2c-mv64xxx
driver. When running an atomic_xfer a bool flag in the driver data is
set, the interrupt is not unmasked on transfer start, and the IRQ
handler is manually invoked while waiting for pending transfers to
complete.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7890fce620 ]
Value comes from DT, so it could be 0. Unlikely, but could be.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
