commit 6d0b1c0184 upstream.
Errata i2312 [0] for K3 silicon mentions the maximum obtainable
timeout through MMC host controller is 700ms. And for commands taking
longer than 700ms, hardware timeout should be disabled and software
timeout should be used.
The workaround for Errata i2312 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci_am654.
[0] https://www.ti.com/lit/pdf/sprz487
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 41fd4caeb0 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250626231452.3460987-1-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff09b71bf9 upstream.
The dma_unmap_sg() functions should be called with the same nents as the
dma_map_sg(), not the value the map function returned.
Fixes: 2f5da67835 ("mmc: bcm2835: Properly handle dmaengine_prep_slave_sg")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250630093510.82871-2-fourier.thomas@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5de469990 upstream.
If msdc_prepare_data() fails to map the DMA region, the request is
not prepared for data receiving, but msdc_start_data() proceeds
the DMA with previous setting.
Since this will lead a memory corruption, we have to stop the
request operation soon after the msdc_prepare_data() fails to
prepare it.
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Fixes: 208489032b ("mmc: mediatek: Add Mediatek MMC driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/174972756982.3337526.6755001617701603082.stgit@mhiramat.tok.corp.google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 539d80575b upstream.
When swiotlb buffer is full, the dma_map_sg() returns 0 to
msdc_prepare_data(), but it does not check it and sets the
MSDC_PREPARE_FLAG.
swiotlb_tbl_map_single() /* prints "swiotlb buffer is full" */
<-swiotlb_map()
<-dma_direct_map_page()
<-dma_direct_map_sg()
<-__dma_map_sg_attrs()
<-dma_map_sg_attrs()
<-dma_map_sg() /* returns 0 (pages mapped) */
<-msdc_prepare_data()
Then, the msdc_unprepare_data() checks MSDC_PREPARE_FLAG and calls
dma_unmap_sg() with unmapped pages. It causes a page fault.
To fix this problem, Do not set MSDC_PREPARE_FLAG if dma_map_sg()
fails because this is not prepared.
Fixes: 208489032b ("mmc: mediatek: Add Mediatek MMC driver")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Tested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/174908565814.4056588.769599127120955383.stgit@mhiramat.tok.corp.google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcc3bcfc5b upstream.
It has turned out the trying to strictly conform to the SDHCI specification
is causing problems. Let's revert and start over.
This reverts commit fb3bbc46c9.
Cc: Erick Shepherd <erick.shepherd@ni.com>
Cc: stable@vger.kernel.org
Fixes: fb3bbc46c9 ("mmc: sdhci: Disable SD card clock before changing parameters")
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Reported-by: Jonathan Liu <net147@gmail.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Closes: https://bugs.debian.org/1108065
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20250624110932.176925-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb3bbc46c9 ]
Per the SD Host Controller Simplified Specification v4.20 §3.2.3, change
the SD card clock parameters only after first disabling the external card
clock. Doing this fixes a spurious clock pulse on Baytrail and Apollo Lake
SD controllers which otherwise breaks voltage switching with a specific
Swissbit SD card.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: Erick Shepherd <erick.shepherd@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250211214645.469279-1-erick.shepherd@ni.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cbe799ac1 ]
Add support for Exynos7870 DW MMC controllers, for both SMU and non-SMU
variants. These controllers require a quirk to access 64-bit FIFO in 32-bit
accesses (DW_MMC_QUIRK_FIFO64_32).
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250219-exynos7870-mmc-v2-3-b4255a3e39ed@disroot.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31e75ed964 ]
The SD spec version 6.0 section 6.4.1.5 requires that Vdd must be
lowered to less than 0.5V for a minimum of 1 ms when powering off a
card. Increase wait to 15 ms so that voltage has time to drain down
to 0.5V and cards can power off correctly. Issues with voltage drain
time were only observed on Apollo Lake and Bay Trail host controllers
so this fix is limited to those devices.
Signed-off-by: Erick Shepherd <erick.shepherd@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250314195021.1588090-1-erick.shepherd@ni.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbef7442fb ]
The driver leaks the device reference taken with
of_find_device_by_node(). Fix the leak by using devm_of_qcom_ice_get().
Fixes: c7eed31e23 ("mmc: sdhci-msm: Switch to the new ICE API")
Cc: stable@vger.kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250117-qcom-ice-fix-dev-leak-v2-2-1ffa5b6884cb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57c0902f8b ]
In certain DW MMC implementations (such as in some Exynos7870
controllers), 64-bit read/write is not allowed from a 64-bit FIFO.
Add a quirk which facilitates accessing the 64-bit FIFO registers in two
32-bit halves.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250219-exynos7870-mmc-v2-2-b4255a3e39ed@disroot.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 49d1626351 upstream.
We have received reports about cards can become corrupt related to the
aggressive PM support. Let's make a partial revert of the change that
enabled the feature.
Reported-by: David Owens <daowens01@gmail.com>
Reported-by: Romain Naour <romain.naour@smile.fr>
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Fixes: 3edf588e7f ("mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20250312121712.1168007-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e51a349d2d upstream.
The error path when atmci_configure_dma() set dma fails in atmci driver
does not correctly disable the clock.
Add the missing clk_disable_unprepare() to the error path for pair with
clk_prepare_enable().
Fixes: 467e081d23 ("mmc: atmel-mci: use probe deferring if dma controller is not ready yet")
Signed-off-by: Gu Bowen <gubowen5@huawei.com>
Acked-by: Aubin Constans <aubin.constans@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250225022856.3452240-1-gubowen5@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e68abf2b9 upstream.
For hs400(es) mode, the 'hs400-ds-delay' is typically configured in the
dts. However, some projects may only define 'mediatek,hs400-ds-dly3',
which can lead to initialization failures in hs400es mode. CMD13 reported
response crc error in the mmc_switch_status() just after switching to
hs400es mode.
[ 1.914038][ T82] mmc0: mmc_select_hs400es failed, error -84
[ 1.914954][ T82] mmc0: error -84 whilst initialising MMC card
Currently, the hs400_ds_dly3 value is set within the tuning function. This
means that the PAD_DS_DLY3 field is not configured before tuning process,
which is the reason for the above-mentioned CMD13 response crc error.
Move the PAD_DS_DLY3 field configuration into msdc_prepare_hs400_tuning(),
and add a value check of hs400_ds_delay to prevent overwriting by zero when
the 'hs400-ds-delay' is not set in the dts. In addition, since hs400(es)
only tune the PAD_DS_DLY1, the PAD_DS_DLY2_SEL bit should be cleared to
bypass it.
Fixes: c4ac38c653 ("mmc: mtk-sd: Add HS400 online tuning support")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250123092644.7359-1-andy-ld.lu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20a0c37e44 ]
Qualcomm regulator supports two power supply modes: HPM and LPM.
Currently, the sdhci-msm.c driver does not set the load to adjust
the current for eMMC and SD. If the regulator dont't set correct
load in LPM state, it will lead to the inability to properly
initialize eMMC and SD.
Set the correct regulator current for eMMC and SD to ensure that the
device can work normally even when the regulator is in LPM.
Signed-off-by: Yuanjie Yang <quic_yuanjiey@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250114083514.258379-1-quic_yuanjiey@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d90a86ed0 upstream.
Commit c7eed31e23 ("mmc: sdhci-msm: Switch to the new ICE API")
introduced an incorrect check of the algorithm ID into the key eviction
path, and thus qcom_ice_evict_key() is no longer ever called. Fix it.
Fixes: c7eed31e23 ("mmc: sdhci-msm: Switch to the new ICE API")
Cc: stable@vger.kernel.org
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Message-ID: <20241213041958.202565-6-ebiggers@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3d87abe11 upstream.
Current implementation leaves pdev->dev as a wakeup source. Add a
device_init_wakeup(&pdev->dev, false) call in the .remove() function and
in the error path of the .probe() function.
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Fixes: 527f36f5ef ("mmc: mediatek: add support for SDIO eint wakup IRQ")
Cc: stable@vger.kernel.org
Message-ID: <20241203023442.2434018-1-joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4dede2b76f ]
Enable SDHCI_QUIRK_NO_LED for i.MX7ULP, i.MX8MM, i.MX8QXP and
i.MXRT1050. Even there is LCTL register bit, there is no IOMUX PAD
for it. So there is no sense to enable LED for SDHCI for these SoCs.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240923062016.1165868-1-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7f0fa47cee upstream.
The Vexia Edu Atla 10 tablet distributed to schools in the Spanish
Andalucía region has no ACPI fwnode associated with the SDHCI controller
for its microsd-slot and thus has no ACPI GPIO resource info.
This causes the following error to be logged and the slot to not work:
[ 10.572113] sdhci-pci 0000:00:12.0: failed to setup card detect gpio
Add a DMI quirk table for providing gpiod_lookup_tables with manually
provided CD GPIO info and use this DMI table to provide the CD GPIO info
on this tablet. This fixes the microsd-slot not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Message-ID: <20241118210049.311079-1-hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2508925fb3 ]
Currently, the MMC_CAP2_CRYPTO flag is set by default for eMMC hosts.
However, this flag should not be set for hosts that do not support inline
encryption.
The 'crypto' clock, as described in the documentation, is used for data
encryption and decryption. Therefore, only hosts that are configured with
this 'crypto' clock should have the MMC_CAP2_CRYPTO flag set.
Fixes: 7b438d0377 ("mmc: mtk-sd: add Inline Crypto Engine clock control")
Fixes: ed299eda8f ("mmc: mtk-sd: fix devm_clk_get_optional usage")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Cc: stable@vger.kernel.org
Message-ID: <20241111085039.26527-1-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed299eda8f ]
This already returns NULL when not found. However, it can return
EPROBE_DEFER and should thus return here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://lore.kernel.org/r/20240930224919.355359-4-rosenp@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 2508925fb3 ("mmc: mtk-sd: Fix MMC_CAP2_CRYPTO flag setting")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 291220451c ]
In the probe function, it goes to 'release_mem' label and returns after
some procedure failure. But if the clocks (partial or all) have been
enabled previously, they would not be disabled in msdc_runtime_suspend,
since runtime PM is not yet enabled for this case.
That cause mmc related clocks always on during system suspend and block
suspend flow. Below log is from a SDCard issue of MT8196 chromebook, it
returns -ETIMEOUT while polling clock stable in the msdc_ungate_clock()
and probe failed, but the enabled clocks could not be disabled anyway.
[ 129.059253] clk_chk_dev_pm_suspend()
[ 129.350119] suspend warning: msdcpll is on
[ 129.354494] [ck_msdc30_1_sel : enabled, 1, 1, 191999939, ck_msdcpll_d2]
[ 129.362787] [ck_msdcpll_d2 : enabled, 1, 1, 191999939, msdcpll]
[ 129.371041] [ck_msdc30_1_ck : enabled, 1, 1, 191999939, ck_msdc30_1_sel]
[ 129.379295] [msdcpll : enabled, 1, 1, 383999878, clk26m]
Add a new 'release_clk' label and reorder the error handle functions to
make sure the clocks be disabled after probe failure.
Fixes: ffaea6ebfe ("mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling")
Fixes: 7a2fa8eed9 ("mmc: mtk-sd: use devm_mmc_alloc_host")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Message-ID: <20241107121215.5201-1-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 328bda09cc ]
GCC 13 complains about the truncated output of snprintf():
drivers/mmc/host/mmc_spi.c: In function ‘mmc_spi_response_get’:
drivers/mmc/host/mmc_spi.c:227:64: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^
drivers/mmc/host/mmc_spi.c:227:9: note: ‘snprintf’ output between 26 and 43 bytes into a destination of size 32
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
228 | cmd->opcode, maptype(cmd));
Drop it and fold the string it generates into the only place where it's
emitted - the dev_dbg() call at the end of the function.
Fixes: 15a0580ced ("mmc_spi host driver")
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241008160134.69934-1-brgl@bgdev.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 85b580afc2 upstream.
It turns out that the Allwinner A100/A133 SoC only supports 8K DMA
blocks (13 bits wide), for both the SD/SDIO and eMMC instances.
And while this alone would make a trivial fix, the H616 falls back to
the A100 compatible string, so we have to now match the H616 compatible
string explicitly against the description advertising 64K DMA blocks.
As the A100 is now compatible with the D1 description, let the A100
compatible string point to that block instead, and introduce an explicit
match against the H616 string, pointing to the old description.
Also remove the redundant setting of clk_delays to NULL on the way.
Fixes: 3536b82e58 ("mmc: sunxi: add support for A100 mmc controller")
Cc: stable@vger.kernel.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Parthiban Nallathambi <parthiban@linumiz.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Message-ID: <20241107014240.24669-1-andre.przywara@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1635e407a4 upstream.
The commit 8396c793ff ("mmc: dw_mmc: Fix IDMAC operation with pages
bigger than 4K") increased the max_req_size, even for 4K pages, causing
various issues:
- Panic booting the kernel/rootfs from an SD card on Rockchip RK3566
- Panic booting the kernel/rootfs from an SD card on StarFive JH7100
- "swiotlb buffer is full" and data corruption on StarFive JH7110
At this stage no fix have been found, so it's probably better to just
revert the change.
This reverts commit 8396c793ff.
Cc: stable@vger.kernel.org
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 8396c793ff ("mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K")
Closes: https://lore.kernel.org/linux-mmc/614692b4-1dbe-31b8-a34d-cb6db1909bb7@w6rz.net/
Closes: https://lore.kernel.org/linux-mmc/CAC8uq=Ppnmv98mpa1CrWLawWoPnu5abtU69v-=G-P7ysATQ2Pw@mail.gmail.com/
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-ID: <20241110114700.622372-1-aurelien@aurel32.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4dedaaeb3 upstream.
When starting the SD Express process, the low power negotiation mode will
be disabled, so we need to re-enable it after switching back to SD mode.
Fixes: 0e92aec2ef ("mmc: sdhci-pci-gli: Add support SD Express card for GL9767")
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Cc: stable@vger.kernel.org
Message-ID: <20241025060017.1663697-2-benchuanggli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c68b5656e upstream.
On sdhci_gl9767_set_clock(), the vendor header space(VHS) is read-only
after calling gl9767_disable_ssc_pll() and gl9767_set_ssc_pll_205mhz().
So the low power negotiation mode cannot be enabled again.
Introduce gl9767_set_low_power_negotiation() function to fix it.
The explanation process is as below.
static void sdhci_gl9767_set_clock()
{
...
gl9767_vhs_write();
...
value |= PCIE_GLI_9767_CFG_LOW_PWR_OFF;
pci_write_config_dword(pdev, PCIE_GLI_9767_CFG, value); <--- (a)
gl9767_disable_ssc_pll(); <--- (b)
sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
if (clock == 0)
return; <-- (I)
...
if (clock == 200000000 && ios->timing == MMC_TIMING_UHS_SDR104) {
...
gl9767_set_ssc_pll_205mhz(); <--- (c)
}
...
value &= ~PCIE_GLI_9767_CFG_LOW_PWR_OFF;
pci_write_config_dword(pdev, PCIE_GLI_9767_CFG, value); <-- (II)
gl9767_vhs_read();
}
(a) disable low power negotiation mode. When return on (I), the low power
mode is disabled. After (b) and (c), VHS is read-only, the low power mode
cannot be enabled on (II).
Reported-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Fixes: d275435551 ("mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL9767")
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Message-ID: <20241025060017.1663697-1-benchuanggli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aea62c744a upstream.
To check if mmc cqe is in halt state, need to check set/clear of CQHCI_HALT
bit. At this time, we need to check with &, not &&.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Seunghwan Baek <sh8267.baek@samsung.com>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240829061823.3718-2-sh8267.baek@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e540da4c1 upstream.
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Fixes: bb7b8ec62d ("mmc: sdhci-of-aspeed: Add support for the ASPEED SD controller")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240826124851.379759-1-liaochen4@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8396c793ff upstream.
Commit 616f876617 ("mmc: pass queue_limits to blk_mq_alloc_disk") [1]
revealed the long living issue in dw_mmc.c driver, existing since the
time when it was first introduced in commit f95f3850f7 ("mmc: dw_mmc:
Add Synopsys DesignWare mmc host driver."), also making kernel boot
broken on platforms using dw_mmc driver with 16K or 64K pages enabled,
with this message in dmesg:
mmcblk: probe of mmc0:0001 failed with error -22
That's happening because mmc_blk_probe() fails when it calls
blk_validate_limits() consequently, which returns the error due to
failed max_segment_size check in this code:
/*
* The maximum segment size has an odd historic 64k default that
* drivers probably should override. Just like the I/O size we
* require drivers to at least handle a full page per segment.
*/
...
if (WARN_ON_ONCE(lim->max_segment_size < PAGE_SIZE))
return -EINVAL;
In case when IDMAC (Internal DMA Controller) is used, dw_mmc.c always
sets .max_seg_size to 4 KiB:
mmc->max_seg_size = 0x1000;
The comment in the code above explains why it's incorrect. Arnd
suggested setting .max_seg_size to .max_req_size to fix it, which is
also what some other drivers are doing:
$ grep -rl 'max_seg_size.*=.*max_req_size' drivers/mmc/host/ | \
wc -l
18
This change is not only fixing the boot with 16K/64K pages, but also
leads to a better MMC performance. The linear write performance was
tested on E850-96 board (eMMC only), before commit [1] (where it's
possible to boot with 16K/64K pages without this fix, to be able to do
a comparison). It was tested with this command:
# dd if=/dev/zero of=somefile bs=1M count=500 oflag=sync
Test results are as follows:
- 4K pages, .max_seg_size = 4 KiB: 94.2 MB/s
- 4K pages, .max_seg_size = .max_req_size = 512 KiB: 96.9 MB/s
- 16K pages, .max_seg_size = 4 KiB: 126 MB/s
- 16K pages, .max_seg_size = .max_req_size = 2 MiB: 128 MB/s
- 64K pages, .max_seg_size = 4 KiB: 138 MB/s
- 64K pages, .max_seg_size = .max_req_size = 8 MiB: 138 MB/s
Unfortunately, SD card controller is not enabled in E850-96 yet, so it
wasn't possible for me to run the test on some cheap SD cards to check
this patch's impact on those. But it's possible that this change might
also reduce the writes count, thus improving SD/eMMC longevity.
All credit for the analysis and the suggested solution goes to Arnd.
[1] https://lore.kernel.org/all/20240215070300.2200308-18-hch@lst.de/
Fixes: f95f3850f7 ("mmc: dw_mmc: Add Synopsys DesignWare mmc host driver.")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/all/CA+G9fYtddf2Fd3be+YShHP6CmSDNcn0ptW8qg+stUKW+Cn0rjQ@mail.gmail.com/
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240306232052.21317-1-semen.protsenko@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6275c7bc8d upstream.
Fix a race condition if the clock provider comes up after mmc is probed,
this causes mmc to fail without retrying.
When given the DEFER error from the clk source, pass it on up the chain.
Fixes: f90a0612f0 ("mmc: dw_mmc: lookup for optional biu and ciu clocks")
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240811212212.123255-1-ben.whitten@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9374ae912d upstream.
When we use cmd8 as the tuning command in hs400 mode, the command
response sent back by some eMMC devices cannot be correctly sampled
by MTK eMMC controller at some weak sample timing. In this case,
command timeout error may occur. So we must receive the following
data to make sure the next cmd8 send correctly.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Fixes: c4ac38c653 ("mmc: mtk-sd: Add HS400 online tuning support")
Cc: stable@vger.stable.com
Link: https://lore.kernel.org/r/20240716013704.10578-1-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab069ce125 upstream.
sdhci_check_ro() can call mmc_gpio_get_ro() while holding the sdhci
host->lock spinlock. That would be a problem if the GPIO access done by
mmc_gpio_get_ro() needed to sleep.
However, host->lock is not needed anyway. The mmc core ensures that host
operations do not race with each other, and asynchronous callbacks like the
interrupt handler, software timeouts, completion work etc, cannot affect
sdhci_check_ro().
So remove the locking.
Fixes: 6d5cd068ee ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240614080051.4005-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbd64f902b upstream.
mmc_of_parse() reads device property "wp-inverted" and sets
MMC_CAP2_RO_ACTIVE_HIGH if it is true. MMC_CAP2_RO_ACTIVE_HIGH is used
to invert a write-protect (AKA read-only) GPIO value.
sdhci_get_property() also reads "wp-inverted" and sets
SDHCI_QUIRK_INVERTED_WRITE_PROTECT which is used to invert the
write-protect value as well but also acts upon a value read out from the
SDHCI_PRESENT_STATE register.
Many drivers call both mmc_of_parse() and sdhci_get_property(),
so that both MMC_CAP2_RO_ACTIVE_HIGH and
SDHCI_QUIRK_INVERTED_WRITE_PROTECT will be set if the controller has
device property "wp-inverted".
Amend the logic in sdhci_check_ro() to allow for that possibility,
so that the write-protect value is not inverted twice.
Also do not invert the value if it is a negative error value. Note that
callers treat an error the same as not-write-protected, so the result is
functionally the same in that case.
Also do not invert the value if sdhci host operation ->get_ro() is used.
None of the users of that callback set SDHCI_QUIRK_INVERTED_WRITE_PROTECT
directly or indirectly, but two do call mmc_gpio_get_ro(), so leave it to
them to deal with that if they ever set SDHCI_QUIRK_INVERTED_WRITE_PROTECT
in the future.
Fixes: 6d5cd068ee ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240614080051.4005-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebc4fc34ea upstream.
jmicron_pmos() and sdhci_pci_probe() use pci_{read,write}_config_byte()
that return PCIBIOS_* codes. The return code is then returned as is by
jmicron_probe() and sdhci_pci_probe(). Similarly, the return code is
also returned as is from jmicron_resume(). Both probe and resume
functions should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning them the fix these issues.
Fixes: 7582041ff3 ("mmc: sdhci-pci: fix simple_return.cocci warnings")
Fixes: 45211e2159 ("sdhci: toggle JMicron PMOS setting")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240527132443.14038-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d77dc388cd upstream.
When erase/trim/discard completion was converted to mmc_poll_for_busy(),
optional support to poll with the host_ops->card_busy() callback was also
added.
The common sdhci's ->card_busy() turns out not to be working as expected
for the sdhci-brcmstb variant, as it keeps returning busy beyond the card's
busy period. In particular, this leads to the below splat for
mmc_do_erase() when running a discard (BLKSECDISCARD) operation during
mkfs.f2fs:
Info: [/dev/mmcblk1p9] Discarding device
[ 39.597258] sysrq: Show Blocked State
[ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d
[ 39.610609] Call trace:
[ 39.613098] __switch_to+0xd8/0xf4
[ 39.616582] __schedule+0x440/0x4f4
[ 39.620137] schedule+0x2c/0x48
[ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114
[ 39.628562] schedule_hrtimeout_range+0x10/0x18
[ 39.633169] usleep_range_state+0x5c/0x90
[ 39.637253] __mmc_poll_for_busy+0xec/0x128
[ 39.641514] mmc_poll_for_busy+0x48/0x70
[ 39.645511] mmc_do_erase+0x1ec/0x210
[ 39.649237] mmc_erase+0x1b4/0x1d4
[ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac
[ 39.657037] mmc_mq_queue_rq+0x18c/0x214
[ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528
[ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac
[ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c
[ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c
[ 39.680668] blk_mq_flush_plug_list+0x200/0x33c
[ 39.685278] blk_add_rq_to_plug+0x68/0xd8
[ 39.689365] blk_mq_submit_bio+0x3a4/0x458
[ 39.693539] __submit_bio+0x1c/0x80
[ 39.697096] submit_bio_noacct_nocheck+0x94/0x174
[ 39.701875] submit_bio_noacct+0x1b0/0x22c
[ 39.706042] submit_bio+0xac/0xe8
[ 39.709424] blk_next_bio+0x4c/0x5c
[ 39.712973] blkdev_issue_secure_erase+0x118/0x170
[ 39.717835] blkdev_common_ioctl+0x374/0x728
[ 39.722175] blkdev_ioctl+0x8c/0x2b0
[ 39.725816] vfs_ioctl+0x24/0x40
[ 39.729117] __arm64_sys_ioctl+0x5c/0x8c
[ 39.733114] invoke_syscall+0x68/0xec
[ 39.736839] el0_svc_common.constprop.0+0x70/0xd8
[ 39.741609] do_el0_svc+0x18/0x20
[ 39.744981] el0_svc+0x68/0x94
[ 39.748107] el0t_64_sync_handler+0x88/0x124
[ 39.752455] el0t_64_sync+0x168/0x16c
To fix the problem let's override the host_ops->card_busy() callback by
setting it to NULL, which forces the mmc core to poll with a CMD13 and
checking the R1_STATUS in the mmc_busy_cb() function.
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Fixes: 0d84c3e6a5 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240603220834.21989-2-kamal.dasu@broadcom.com
[Ulf: Clarified the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a91bf3b3be upstream.
sdhci_pci_o2_probe() uses pci_read_config_{byte,dword}() that return
PCIBIOS_* codes. The return code is then returned as is but as
sdhci_pci_o2_probe() is probe function chain, it should return normal
errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning them. Add a label for read failure so that the
conversion can be done in one place rather than on all of the return
statements.
Fixes: 3d757ddbd6 ("mmc: sdhci-pci-o2micro: add Bayhub new chip GG8 support for UHS-I")
Fixes: d599005afd ("mmc: sdhci-pci-o2micro: Add missing checks in sdhci_pci_o2_probe")
Fixes: 706adf6bc3 ("mmc: sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support")
Fixes: 01acf6917a ("mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts")
Fixes: 26daa1ed40 ("mmc: sdhci: Disable ADMA on some O2Micro SD/MMC parts.")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240527132443.14038-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 431946c0f6 upstream.
The card-detect GPIO for the microSD slot on Asus T100TA / T100TAM models
stopped working under Linux after commit 6fd03f0248 ("gpiolib: acpi:
support bias pull disable").
The GPIO in question is connected to a mechanical switch in the slot
which shorts the pin to GND when a card is inserted.
The GPIO pin correctly gets configured with a 20K pull-up by the BIOS,
but there is a bug in the DSDT where the GpioInt for the card-detect is
configured with a PullNone setting:
GpioInt (Edge, ActiveBoth, SharedAndWake, PullNone, 0x2710,
"\\_SB.GPO0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0026
}
Linux now actually honors the PullNone setting and disables the 20K pull-up
configured by the BIOS.
Add a new DMI_QUIRK_SD_CD_ENABLE_PULL_UP quirk which when set calls
mmc_gpiod_set_cd_config() to re-enable the pull-up and set this for
the Asus T100TA models to fix this.
Fixes: 6fd03f0248 ("gpiolib: acpi: support bias pull disable")
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-7-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef3eab75e1 upstream.
On the Toshiba WT10-A the microSD slot always reports the card being
write-protected, just like on the Toshiba WT8-B.
Add a DMI quirk to work around this.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-6-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3521d7cba upstream.
The Lenovo Yoga Tablet 2 Pro 1380 sdcard slot has an active high cd pin
and a broken wp pin which always reports the card being write-protected.
Add a DMI quirk to address both issues.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-5-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
