commit 099cf1fbb8 upstream.
The deadlock can occur due to a recursive lock acquisition of
`cros_typec_altmode_data::mutex`.
The call chain is as follows:
1. cros_typec_altmode_work() acquires the mutex
2. typec_altmode_vdm() -> dp_altmode_vdm() ->
3. typec_altmode_exit() -> cros_typec_altmode_exit()
4. cros_typec_altmode_exit() attempts to acquire the mutex again
To prevent this, defer the `typec_altmode_exit()` call by scheduling
it rather than calling it directly from within the mutex-protected
context.
Cc: stable <stable@kernel.org>
Fixes: b4b38ffb38 ("usb: typec: displayport: Receive DP Status Update NAK request exit dp altmode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250624133246.3936737-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cee4392a57 upstream.
Some varieties of this device don't work with
RESET_RESUME alone.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250605122852.1440382-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31a6afbe86 upstream.
Shawn and John reported a hang issue during system suspend as below:
- USB gadget is enabled as Ethernet
- There is data transfer over USB Ethernet (scp a big file between host
and device)
- Device is going in/out suspend (echo mem > /sys/power/state)
The root cause is the USB device controller is suspended but the USB bus
is still active which caused the USB host continues to transfer data with
device and the device continues to queue USB requests (in this case, a
delayed TCP ACK packet trigger the issue) after controller is suspended,
however the USB controller clock is already gated off. Then if udc driver
access registers after that point, the system will hang.
The correct way to avoid such issue is to disconnect device from host when
the USB bus is not at suspend state. Then the host will receive disconnect
event and stop data transfer in time. To continue make USB gadget device
work after system resume, this will reconnect device automatically.
To make usb wakeup work if USB bus is already at suspend state, this will
keep connection for it only when USB device controller has enabled wakeup
capability.
Reported-by: Shawn Guo <shawnguo@kernel.org>
Reported-by: John Ernberg <john.ernberg@actia.se>
Closes: https://lore.kernel.org/linux-usb/aEZxmlHmjeWcXiF3@dragon/
Tested-by: John Ernberg <john.ernberg@actia.se> # iMX8QXP
Fixes: 235ffc17d0 ("usb: chipidea: udc: add suspend/resume support for device controller")
Cc: stable <stable@kernel.org>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250614124914.207540-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e2c421ef8 upstream.
It doesn't need to do it, and the related command event returns
'Slot Not Enabled Error' status.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Suggested-by: Hongliang Yang <hongliang.yang@cixtech.com>
Reviewed-by: Fugang Duan <fugang.duan@cixtech.com>
Signed-off-by: Peter Chen <peter.chen@cixtech.com>
Link: https://lore.kernel.org/r/20250619013413.35817-1-peter.chen@cixtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efe3e3ae5a upstream.
Flush dbc requests when dbc is stopped and transfer rings are freed.
Failure to flush them lead to leaking memory and dbc completing odd
requests after resuming from suspend, leading to error messages such as:
[ 95.344392] xhci_hcd 0000:00:0d.0: no matched request
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250627144127.3889714-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b857d69a5 upstream.
When /dev/ttyDBC0 device is created then by default ECHO flag
is set for the terminal device. However if data arrives from
a peer before application using /dev/ttyDBC0 applies its set
of terminal flags then the arriving data will be echoed which
might not be desired behavior.
Fixes: 4521f16139 ("xhci: dbctty: split dbc tty driver registration and unregistration functions.")
Cc: stable <stable@kernel.org>
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/stable/20250610111802.18742-1-ukaszb%40chromium.org
Link: https://lore.kernel.org/r/20250627144127.3889714-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbc889ab01 upstream.
During the High-Speed Isochronous Audio transfers, xHCI
controller on certain AMD platforms experiences momentary data
loss. This results in Missed Service Errors (MSE) being
generated by the xHCI.
The root cause of the MSE is attributed to the ISOC OUT endpoint
being omitted from scheduling. This can happen when an IN
endpoint with a 64ms service interval either is pre-scheduled
prior to the ISOC OUT endpoint or the interval of the ISOC OUT
endpoint is shorter than that of the IN endpoint. Consequently,
the OUT service is neglected when an IN endpoint with a service
interval exceeding 32ms is scheduled concurrently (every 64ms in
this scenario).
This issue is particularly seen on certain older AMD platforms.
To mitigate this problem, it is recommended to adjust the service
interval of the IN endpoint to not exceed 32ms (interval 8). This
adjustment ensures that the OUT endpoint will not be bypassed,
even if a smaller interval value is utilized.
Cc: stable <stable@kernel.org>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250627144127.3889714-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af4db5a35a upstream.
A poorly implemented DisplayPort Alt Mode port partner can indicate
that its pin assignment capabilities are greater than the maximum
value, DP_PIN_ASSIGN_F. In this case, calls to pin_assignment_show
will cause a BRK exception due to an out of bounds array access.
Prevent for loop in pin_assignment_show from accessing
invalid values in pin_assignments by adding DP_PIN_ASSIGN_MAX
value in typec_dp.h and using i < DP_PIN_ASSIGN_MAX as a loop
condition.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250618224943.3263103-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f7bbef179 ]
Since the typec connectors can have many muxes or switches for different
lanes (sbu, usb2, usb3) going into different modal states (usb2, usb3,
audio, debug) all of them will be called on typec_switch_set and
typec_mux_set. But not all of them will be handling the expected mode.
If one of the mux or switch will come back with EOPTNOSUPP this is no
reason to stop running through the next ones. Therefor we skip this
particular error value and continue calling the next.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-typec-mux-v1-1-22c0526381ba@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4b38ffb38 ]
Although some Type-C DRD devices that do not support the DP Sink
function (such as Huawei Mate 40Pro), the Source Port initiates
Enter Mode CMD, but the device responds to Enter Mode ACK, the
Source port then initiates DP Status Update CMD, and the device
responds to DP Status Update NAK.
As PD2.0 spec ("6.4.4.3.4 Enter Mode Command")，A DR_Swap Message
Shall Not be sent during Modal Operation between the Port Partners.
At this time, the source port initiates DR_Swap message through the
"echo device > /sys/class/typec/port0/data_role" command to switch
the data role from host to device. The device will initiate a Hard
Reset for recovery, resulting in the failure of data role swap.
Therefore, when DP Status Update NAK is received, Exit Mode CMD is
initiated to exit the currently entered DP altmode.
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250209071926.69625-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 387602d8a7 ]
Don't set WDM_READ flag in wdm_in_callback() for ZLP-s, otherwise when
userspace tries to poll for available data, it might - incorrectly -
believe there is something available, and when it tries to non-blocking
read it, it might get stuck in the read loop.
For example this is what glib does for non-blocking read (briefly):
1. poll()
2. if poll returns with non-zero, starts a read data loop:
a. loop on poll() (EINTR disabled)
b. if revents was set, reads data
I. if read returns with EINTR or EAGAIN, goto 2.a.
II. otherwise return with data
So if ZLP sets WDM_READ (#1), we expect data, and try to read it (#2).
But as that was a ZLP, and we are doing non-blocking read, wdm_read()
returns with EAGAIN (#2.b.I), so loop again, and try to read again
(#2.a.).
With glib, we might stuck in this loop forever, as EINTR is disabled
(#2.a).
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250403144004.3889125-1-robert.hodaszi@digi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82fe5107fa ]
When creating a device path in the driver the snprintf() takes
up to 16 characters long argument along with the additional up to
12 characters for the signed integer (as it can't see the actual limits)
and tries to pack this into 16 bytes array. GCC complains about that
when build with `make W=1`:
drivers/usb/core/usb.c:705:25: note: ‘snprintf’ output between 3 and 28 bytes into a destination of size 16
Since everything works until now, let's just check for the potential
buffer overflow and bail out. It is most likely a never happen situation,
but at least it makes GCC happy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250321164949.423957-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4e5b10c55 ]
The current implementation of the usb-conn-gpio driver uses a fixed
"usb-charger" name for all USB connector devices. This causes conflicts
in the power supply subsystem when multiple USB connectors are present,
as duplicate names are not allowed.
Use IDA to manage unique IDs for naming usb connectors (e.g.,
usb-charger-0, usb-charger-1).
Signed-off-by: Chance Yang <chance.yang@kneron.us>
Link: https://lore.kernel.org/r/20250411-work-next-v3-1-7cd9aa80190c@kneron.us
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1538740103 ]
The variable tpgt in usbg_make_tpg() is defined as unsigned long and is
assigned to tpgt->tport_tpgt, which is defined as u16. This may cause an
integer overflow when tpgt is greater than USHRT_MAX (65535). I
haven't tried to trigger it myself, but it is possible to trigger it
by calling usbg_make_tpg() with a large value for tpgt.
I modified the type of tpgt to match tpgt->tport_tpgt and adjusted the
relevant code accordingly.
This patch is similar to commit 59c816c1f2 ("vhost/scsi: potential
memory corruption").
Signed-off-by: Chen Yufeng <chenyufeng@iie.ac.cn>
Link: https://lore.kernel.org/r/20250415065857.1619-1-chenyufeng@iie.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af076a41f8 ]
It is possible that the gadget will be disabled, while the udc is
suspended. When enabling the udc in that case, the clock gating
will not be enabled again. Leaving the phy unclocked. Even when the
udc is not enabled, connecting this powered but not clocked phy leads
to enumeration errors on the host side.
To ensure that the clock gating will be in an valid state, we ensure
that the clock gating will be enabled before stopping the udc.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20250417-dwc2_clock_gating-v1-1-8ea7c4d53d73@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0736299d09 upstream.
Register read of TCPC_RX_BYTE_CNT returns the total size consisting of:
PD message (pending read) size + 1 Byte for Frame Type (SOP*)
This is validated against the max PD message (`struct pd_message`) size
without accounting for the extra byte for the frame type. Note that the
struct pd_message does not contain a field for the frame_type. This
results in false negatives when the "PD message (pending read)" is equal
to the max PD message size.
Fixes: 6f413b559f ("usb: typec: tcpci_maxim: Chip level TCPC driver")
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Kyle Tso <kyletso@google.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/stable/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d%40google.com
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89bb3dc13a upstream.
usb core avoids sending a Set-Interface altsetting 0 request after device
reset, and instead relies on calling usb_disable_interface() and
usb_enable_interface() to flush and reset host-side of those endpoints.
xHCI hosts allocate and set up endpoint ring buffers and host_ep->hcpriv
during usb_hcd_alloc_bandwidth() callback, which in this case is called
before flushing the endpoint in usb_disable_interface().
Call usb_disable_interface() before usb_hcd_alloc_bandwidth() to ensure
URBs are flushed before new ring buffers for the endpoints are allocated.
Otherwise host driver will attempt to find and remove old stale URBs
from a freshly allocated new ringbuffer.
Cc: stable <stable@kernel.org>
Fixes: 4fe0387afa ("USB: don't send Set-Interface after reset")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250514132520.225345-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4ecdc3526 upstream.
In some cases, there is a small-time gap in which CMD_RING_BUSY can be
cleared by controller but adding command completion event to event ring
will be delayed. As the result driver will return error code.
This behavior has been detected on usbtest driver (test 9) with
configuration including ep1in/ep1out bulk and ep2in/ep2out isoc
endpoint.
Probably this gap occurred because controller was busy with adding some
other events to event ring.
The CMD_RING_BUSY is cleared to '0' when the Command Descriptor has been
executed and not when command completion event has been added to event
ring.
To fix this issue for this test the small delay is sufficient less than
10us) but to make sure the problem doesn't happen again in the future
the patch introduces 10 retries to check with delay about 20us before
returning error code.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538AA45362ACCF1B94EE9B7DD96A@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acb3dac280 upstream.
The usbtmc488_ioctl_read_stb function relied on a positive return from
usbtmc_get_stb to reset the srq condition in the driver. The
USBTMC_IOCTL_GET_STB case tested for a positive return to return the stb
to the user.
Commit: <cac01bd178d6> ("usb: usbtmc: Fix erroneous get_stb ioctl
error returns") changed the return value of usbtmc_get_stb to 0 on
success instead of returning the value of usb_control_msg which is
positive in the normal case. This change caused the function
usbtmc488_ioctl_read_stb and the USBTMC_IOCTL_GET_STB ioctl to no
longer function correctly.
Change the test in usbtmc488_ioctl_read_stb to test for failure
first and return the failure code immediately.
Change the test for the USBTMC_IOCTL_GET_STB ioctl to test for 0
instead of a positive value.
Fixes: cac01bd178 ("usb: usbtmc: Fix erroneous get_stb ioctl error returns")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250521121656.18174-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe7f7ac8e0 upstream.
Update struct hid_descriptor to better reflect the mandatory and
optional parts of the HID Descriptor as per USB HID 1.11 specification.
Note: the kernel currently does not parse any optional HID class
descriptors, only the mandatory report descriptor.
Update all references to member element desc[0] to rpt_desc.
Add test to verify bLength and bNumDescriptors values are valid.
Replace the for loop with direct access to the mandatory HID class
descriptor member for the report descriptor. This eliminates the
possibility of getting an out-of-bounds fault.
Add a warning message if the HID descriptor contains any unsupported
optional HID class descriptors.
Reported-by: syzbot+c52569baf0c843f35495@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c52569baf0c843f35495
Fixes: f043bfc98c ("HID: usbhid: fix out-of-bounds bug")
Cc: stable@vger.kernel.org
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 342e4955a1 upstream.
wait_event_interruptible_timeout requires a timeout argument
in units of jiffies. It was being called in usbtmc_get_stb
with the usb timeout value which is in units of milliseconds.
Pass the timeout argument converted to jiffies.
Fixes: 048c6d88a0 ("usb: usbtmc: Add ioctls to set/get usb timeout")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250521121656.18174-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4239ace2d upstream.
debugfs.c emits the following warnings when compiling with the -Wsign-conversion flag with clang 15:
drivers/usb/typec/ucsi/debugfs.c:58:27: warning: implicit conversion changes signedness: 'int' to 'u32' (aka 'unsigned int') [-Wsign-conversion]
ucsi->debugfs->status = ret;
~ ^~~
drivers/usb/typec/ucsi/debugfs.c:71:25: warning: implicit conversion changes signedness: 'u32' (aka 'unsigned int') to 'int' [-Wsign-conversion]
return ucsi->debugfs->status;
~~~~~~ ~~~~~~~~~~~~~~~^~~~~~
During ucsi_cmd() we see:
if (ret < 0) {
ucsi->debugfs->status = ret;
return ret;
}
But "status" is u32 meaning unsigned wrap-around occurs when assigning a value which is < 0 to it, this obscures the real status.
To fix this make the "status" of type int since ret is also of type int.
Fixes: df0383ffad ("usb: typec: ucsi: Add debugfs for ucsi commands")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250422134717.66218-1-qasdev00@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a889482b upstream.
Add new bcd (0x905) to support PL2303GT-2AB (TYPE_HXN).
Add new bcd (0x1005) to support PL2303GC-Q20 (TYPE_HXN).
Signed-off-by: Charles Yeh <charlesyeh522@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19f7955919 upstream.
This device exhibits I/O errors during file transfers due to unstable
link power management (LPM) behavior. The kernel logs show repeated
warm resets and eventual disconnection when LPM is enabled:
[ 3467.810740] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0020
[ 3467.810740] usb usb2-port5: do warm reset
[ 3467.866444] usb usb2-port5: not warm reset yet, waiting 50ms
[ 3467.907407] sd 0:0:0:0: [sda] tag#12 sense submit err -19
[ 3467.994423] usb usb2-port5: status 02c0, change 0001, 10.0 Gb/s
[ 3467.994453] usb 2-5: USB disconnect, device number 4
The error -19 (ENODEV) occurs when the device disappears during write
operations. Adding USB_QUIRK_NO_LPM disables link power management
for this specific device, resolving the stability issues.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250508055947.764538-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dfc88357b6 ]
When the device stalls an endpoint, current TD is assigned -EPIPE
status and Reset Endpoint is queued. If a Stop Endpoint is pending
at the time, it will run before Reset Endpoint and fail due to the
stall. Its handler will change TD's status to -EPROTO before Reset
Endpoint handler runs and initiates giveback.
Check if the stall has already been handled and don't try to do it
again. Since xhci_handle_halted_endpoint() performs this check too,
not overwriting td->status is the only difference.
I haven't seen this case yet, but I have seen a related one where
the xHC has already executed Reset Endpoint, EP Context state is
now Stopped and EP_HALTED is set. If the xHC took a bit longer to
execute Reset Endpoint, said case would become this one.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250311154551.4035726-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 364618c89d upstream.
This patch introduces the ucsi_con_mutex_lock / ucsi_con_mutex_unlock
functions to the UCSI driver. ucsi_con_mutex_lock ensures the connector
mutex is only locked if a connection is established and the partner pointer
is valid. This resolves a deadlock scenario where
ucsi_displayport_remove_partner holds con->mutex waiting for
dp_altmode_work to complete while dp_altmode_work attempts to acquire it.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250424084429.3220757-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd33993a97 ]
s/devince/device/
It's used only internally, so no any behavior changes.
Fixes: 37e0e14128 ("ALSA: ump: Support UMP Endpoint and Function Block parsing")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20250511141147.10246-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4e77d3ec7c upstream.
wait_event_interruptible_timeout returns a long
The return value was being assigned to an int causing an integer overflow
when the remaining jiffies > INT_MAX which resulted in random error
returns.
Use a long return value, converting to the int ioctl return only on error.
Fixes: bb99794a47 ("usb: usbtmc: Add ioctl for vendor specific read")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9747c9b8b upstream.
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value, converting to the int ioctl return only on
error.
Fixes: 739240a9f6 ("usb: usbtmc: Add ioctl USBTMC488_IOCTL_WAIT_SRQ")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cac01bd178 upstream.
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value and convert to int ioctl return only on error.
When the return value of wait_event_interruptible_timeout was <= INT_MAX
the number of remaining jiffies was returned which has no meaning for the
user. Return 0 on success.
Reported-by: Michael Katzmann <vk2bea@gmail.com>
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 054c514554 upstream.
usbtmc_read() calls usbtmc_generic_read()
which uses interruptible sleep, but usbtmc_read()
itself uses uninterruptble sleep for mutual exclusion
between threads. That makes no sense.
Both should use interruptible sleep.
Fixes: 5b775f672c ("USB: add USB test and measurement class driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250430134810.226015-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 312d79669e upstream.
This patch ensures that the UCSI driver waits for all pending tasks in the
ucsi_displayport_work workqueue to finish executing before proceeding with
the partner removal.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250424084429.3220757-3-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e918d3959b upstream.
This patch fixes Type-C Compliance Test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
The compliance tester moves into SNK_UNATTACHED during toggling and
expects the PUT to apply Rp after tPDDebounce of detection. If the port
is in SNK_TRY_WAIT_DEBOUNCE, it will move into SRC_TRYWAIT immediately
and apply Rp. This violates TD 4.7.5.V.3, where the tester confirms that
the PUT attaches Rp after the transitions to Unattached.SNK for
tPDDebounce.
Change the tcpm_set_state delay between SNK_TRY_WAIT_DEBOUNCE and
SRC_TRYWAIT to tPDDebounce.
Fixes: a0a3e04e6b ("staging: typec: tcpm: Check for Rp for tPDDebounce")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250429234703.3748506-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 732f35cf8b upstream.
When a USB device is connected to the OTG port, the tegra_xhci_id_work()
routine transitions the PHY to host mode and calls xhci_hub_control()
with the SetPortFeature command to enable port power.
In certain cases, the XHCI controller may be in a low-power state
when this operation occurs. If xhci_hub_control() is invoked while
the controller is suspended, the PORTSC register may return 0xFFFFFFFF,
indicating a read failure. This causes xhci_hc_died() to be triggered,
leading to host controller shutdown.
Example backtrace:
[ 105.445736] Workqueue: events tegra_xhci_id_work
[ 105.445747] dump_backtrace+0x0/0x1e8
[ 105.445759] xhci_hc_died.part.48+0x40/0x270
[ 105.445769] tegra_xhci_set_port_power+0xc0/0x240
[ 105.445774] tegra_xhci_id_work+0x130/0x240
To prevent this, ensure the controller is fully resumed before
interacting with hardware registers by calling pm_runtime_get_sync()
prior to the host mode transition and xhci_hub_control().
Fixes: f836e78430 ("usb: xhci-tegra: Add OTG support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20250422114001.126367-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5977a58dd5 upstream.
Currently when the host sends GET_STATUS request for an interface,
we use get_status callbacks to set/clear remote wakeup capability
of that interface. And if get_status callback isn't present for
that interface, then we assume its remote wakeup capability based
on bmAttributes.
Now consider a scenario, where we have a USB configuration with
multiple interfaces (say ECM + ADB), here ECM is remote wakeup
capable and as of now ADB isn't. And bmAttributes will indicate
the device as wakeup capable. With the current implementation,
when host sends GET_STATUS request for both interfaces, we will
set FUNC_RW_CAP for both. This results in USB3 CV Chapter 9.15
(Function Remote Wakeup Test) failures as host expects remote
wakeup from both interfaces.
The above scenario is just an example, and the failure can be
observed if we use configuration with any interface except ECM.
Hence avoid configuring remote wakeup capability from composite
driver based on bmAttributes, instead use get_status callbacks
and let the function drivers decide this.
Cc: stable <stable@kernel.org>
Fixes: 481c225c48 ("usb: gadget: Handle function suspend feature selector")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-3-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59820fde00 upstream.
We identified a bug where the ST_RC bit in the status register was not
being acknowledged after clearing the CTRL_RUN bit in the control
register. This could lead to unexpected behavior in the USB gadget
drivers.
This patch resolves the issue by adding the necessary code to explicitly
acknowledge ST_RC after clearing CTRL_RUN based on the programming
sequence, ensuring proper state transition.
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Cc: stable <stable@kernel.org>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20250418081228.1194779-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e3820271c upstream.
When host sends GET_STATUS to ECM interface, handle the request
from the function driver. Since the interface is wakeup capable,
set the corresponding bit, and set RW bit if the function is
already armed for wakeup by the host.
Cc: stable <stable@kernel.org>
Fixes: 481c225c48 ("usb: gadget: Handle function suspend feature selector")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-2-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8614ecdb15 upstream.
The controllers with rtl version larger than
RTL_REVISION_NEW_LPM (0x00002700) has bug which causes that controller
doesn't resume from L1 state. It happens if after receiving LPM packet
controller starts transitioning to L1 and in this moment the driver force
resuming by write operation to PORTSC.PLS.
It's corner case and happens when write operation to PORTSC occurs during
device delay before transitioning to L1 after transmitting ACK
time (TL1TokenRetry).
Forcing transition from L1->L0 by driver for revision larger than
RTL_REVISION_NEW_LPM is not needed, so driver can simply fix this issue
through block call of cdnsp_force_l0_go function.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538B55C3A6E71F9ED29E980DD842@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 241e2ce88e upstream.
In very rare cases after resuming controller from L1 to L0 it reads
registers before the clock UTMI have been enabled and as the result
driver reads incorrect value.
Most of registers are in APB domain clock but some of them (e.g. PORTSC)
are in UTMI domain clock.
After entering to L1 state the UTMI clock can be disabled.
When controller transition from L1 to L0 the port status change event is
reported and in interrupt runtime function driver reads PORTSC.
During this read operation controller synchronize UTMI and APB domain
but UTMI clock is still disabled and in result it reads 0xFFFFFFFF value.
To fix this issue driver increases APB timeout value.
The issue is platform specific and if the default value of APB timeout
is not sufficient then this time should be set Individually for each
platform.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953846C57973E4DB134CAA71DDBF2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5c7973539 upstream.
Device tree bindings state that the clock is optional for UHCI platform
controllers, and some existing device trees don't provide those - such
as those for VIA/WonderMedia devices.
The driver however fails to probe now if no clock is provided, because
devm_clk_get returns an error pointer in such case.
Switch to devm_clk_get_optional instead, so that it could probe again
on those platforms where no clocks are given.
Cc: stable <stable@kernel.org>
Fixes: 26c502701c ("usb: uhci: Add clk support to uhci-platform")
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20250425-uhci-clock-optional-v1-1-a1d462592f29@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcdb52d948 upstream.
If xhci_mem_init() fails, it calls into xhci_mem_cleanup() to mop
up the damage. If it fails early enough, before xhci->interrupters
is allocated but after xhci->max_interrupters has been set, which
happens in most (all?) cases, things get uglier, as xhci_mem_cleanup()
unconditionally derefences xhci->interrupters. With prejudice.
Gate the interrupt freeing loop with a check on xhci->interrupters
being non-NULL.
Found while debugging a DMA allocation issue that led the XHCI driver
on this exact path.
Fixes: c99b38c412 ("xhci: add support to allocate several interrupters")
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # 6.8+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240809124408.505786-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bea5892d0e ]
Current xhci bus resume implementation prevents xHC host from generating
interrupts during high-speed USB 2 and super-speed USB 3 bus resume.
Only reason to disable interrupts during bus resume would be to prevent
the interrupt handler from interfering with the resume process of USB 2
ports.
Host initiated resume of USB 2 ports is done in two stages.
The xhci driver first transitions the port from 'U3' to 'Resume' state,
then wait in Resume for 20ms, and finally moves port to U0 state.
xhci driver can't prevent interrupts by keeping the xhci spinlock
due to this 20ms sleep.
Limit interrupt disabling to the USB 2 port resume case only.
resuming USB 2 ports in bus resume is only done in special cases where
USB 2 ports had to be forced to suspend during bus suspend.
The current way of preventing interrupts by clearing the 'Interrupt
Enable' (INTE) bit in USBCMD register won't prevent the Interrupter
registers 'Interrupt Pending' (IP), 'Event Handler Busy' (EHB) and
USBSTS register Event Interrupt (EINT) bits from being set.
New interrupts can't be issued before those bits are properly clered.
Disable interrupts by clearing the interrupter register 'Interrupt
Enable' (IE) bit instead. This way IP, EHB and INTE won't be set
before IE is enabled again and a new interrupt is triggered.
Reported-by: Devyn Liu <liudingyuan@huawei.com>
Closes: https://lore.kernel.org/linux-usb/b1a9e2d51b4d4ff7a304f77c5be8164e@huawei.com/
Cc: stable@vger.kernel.org
Tested-by: Devyn Liu <liudingyuan@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c0c11bb87 ]
Allow creators of seconday interrupters to specify the interrupt
moderation interval value in nanoseconds when creating the interrupter.
If not sure what value to use then use the xhci driver default
xhci->imod_interval
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bea5892d0e ("xhci: Limit time spent with xHC interrupts disabled during bus resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db4460b6ec ]
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c412 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bea5892d0e ("xhci: Limit time spent with xHC interrupts disabled during bus resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ace2162587 ]
Add a helper to set the interrupt moderation interval for an interrupter.
Each interrupter can have its own moderation value.
Hardware has a 16bit register for the moderation value, each step is 250ns.
Helper function imod_interval argument is in nanoseconds.
Values from 0 to 16383750 (250 x 0xffff) are accepted.
0 means no interrupt throttling.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bea5892d0e ("xhci: Limit time spent with xHC interrupts disabled during bus resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
