commit bd496a44f0 upstream.
The I3C master driver may receive an IBI from a target device that has not
been probed yet. In such cases, the master calls `i3c_master_queue_ibi()`
to queue an IBI work task, leading to "Unable to handle kernel read from
unreadable memory" and resulting in a kernel panic.
Typical IBI handling flow:
1. The I3C master scans target devices and probes their respective drivers.
2. The target device driver calls `i3c_device_request_ibi()` to enable IBI
and assigns `dev->ibi = ibi`.
3. The I3C master receives an IBI from the target device and calls
`i3c_master_queue_ibi()` to queue the target device driver’s IBI
handler task.
However, since target device events are asynchronous to the I3C probe
sequence, step 3 may occur before step 2, causing `dev->ibi` to be `NULL`,
leading to a kernel panic.
Add a NULL pointer check in `i3c_master_queue_ibi()` to prevent accessing
an uninitialized `dev->ibi`, ensuring stability.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/Z9gjGYudiYyl3bSe@lizhi-Precision-Tower-5810/
Signed-off-by: Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250326123047.2797946-1-manjunatha.venkatesh@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b266e0d4da upstream.
Fix a probe failure in the i3c master driver that occurs when no i3c
devices are connected to the bus.
The issue arises in `i3c_master_bus_init()` where the `ret` value is not
updated after calling `master->ops->set_speed()`. If no devices are
present, `ret` remains set to `I3C_ERROR_M2`, causing the code to
incorrectly proceed to `err_bus_cleanup`.
Cc: stable@vger.kernel.org
Fixes: aef79e189b ("i3c: master: support to adjust first broadcast address speed")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250108225533.915334-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36faa04ce3 upstream.
When a new device hotjoins, a new dynamic address is assigned.
i3c_master_add_i3c_dev_locked() identifies that the device was previously
attached to the bus and locates the olddev.
i3c_master_add_i3c_dev_locked()
{
...
olddev = i3c_master_search_i3c_dev_duplicate(newdev);
...
if (olddev) {
...
i3c_dev_disable_ibi_locked(olddev);
^^^^^^
The olddev should not receive any commands on the i3c bus as it
does not exist and has been assigned a new address. This will
result in NACK or timeout. So remove it.
}
i3c_dev_free_ibi_locked(olddev);
^^^^^^^^
This function internally calls i3c_dev_disable_ibi_locked() function
causing to send DISEC command with old Address.
The olddev should not receive any commands on the i3c bus as it
does not exist and has been assigned a new address. This will
result in NACK or timeout. So, update the olddev->ibi->enabled
flag to false to avoid DISEC with OldAddr.
}
Include part of Ravindra Yashvant Shinde's work:
https://lore.kernel.org/linux-i3c/20240820151917.3904956-1-ravindra.yashvant.shinde@nxp.com/T/#u
Fixes: 317bacf960 ("i3c: master: add enable(disable) hot join in sys entry")
Co-developed-by: Ravindra Yashvant Shinde <ravindra.yashvant.shinde@nxp.com>
Signed-off-by: Ravindra Yashvant Shinde <ravindra.yashvant.shinde@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241001162232.223724-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 851bd21cdb ]
If the DTS contains 'assigned-address', a dynamic address leak occurs
during hotjoin events.
Assume a device have assigned-address 0xb.
- Device issue Hotjoin
- Call i3c_master_do_daa()
- Call driver xxx_do_daa()
- Call i3c_master_get_free_addr() to get dynamic address 0x9
- i3c_master_add_i3c_dev_locked(0x9)
- expected_dyn_addr = newdev->boardinfo->init_dyn_addr (0xb);
- i3c_master_reattach_i3c_dev(newdev(0xb), old_dyn_addr(0x9));
- if (dev->info.dyn_addr != old_dyn_addr &&
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 0xb != 0x9 -> TRUE
(!dev->boardinfo ||
^^^^^^^^^^^^^^^ -> FALSE
dev->info.dyn_addr != dev->boardinfo->init_dyn_addr)) {
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
0xb != 0xb -> FALSE
...
i3c_bus_set_addr_slot_status(&master->bus, old_dyn_addr,
I3C_ADDR_SLOT_FREE);
^^^
This will be skipped. So old_dyn_addr never free
}
- i3c_master_get_free_addr() will return increased sequence number.
Remove dev->info.dyn_addr != dev->boardinfo->init_dyn_addr condition check.
dev->info.dyn_addr should be checked before calling this function because
i3c_master_setnewda_locked() has already been called and the target device
has already accepted dyn_addr. It is too late to check if dyn_addr is free
in i3c_master_reattach_i3c_dev().
Add check to ensure expected_dyn_addr is free before
i3c_master_setnewda_locked().
Fixes: cc3a392d69 ("i3c: master: fix for SETDASA and DAA process")
Cc: stable@kernel.org
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-3-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f552fa280 ]
Extend the address status bit to 4 and introduce the
I3C_ADDR_SLOT_EXT_DESIRED macro to indicate that a device prefers a
specific address. This is generally set by the 'assigned-address' in the
device tree source (dts) file.
┌────┬─────────────┬───┬─────────┬───┐
│S/Sr│ 7'h7E RnW=0 │ACK│ ENTDAA │ T ├────┐
└────┴─────────────┴───┴─────────┴───┘ │
┌─────────────────────────────────────────┘
│ ┌──┬─────────────┬───┬─────────────────┬────────────────┬───┬─────────┐
└─►│Sr│7'h7E RnW=1 │ACK│48bit UID BCR DCR│Assign 7bit Addr│PAR│ ACK/NACK│
└──┴─────────────┴───┴─────────────────┴────────────────┴───┴─────────┘
Some master controllers (such as HCI) need to prepare the entire above
transaction before sending it out to the I3C bus. This means that a 7-bit
dynamic address needs to be allocated before knowing the target device's
UID information.
However, some I3C targets may request specific addresses (called as
"init_dyn_addr"), which is typically specified by the DT-'s
assigned-address property. Lower addresses having higher IBI priority. If
it is available, i3c_bus_get_free_addr() preferably return a free address
that is not in the list of desired addresses (called as "init_dyn_addr").
This allows the device with the "init_dyn_addr" to switch to its
"init_dyn_addr" when it hot-joins the I3C bus. Otherwise, if the
"init_dyn_addr" is already in use by another I3C device, the target device
will not be able to switch to its desired address.
If the previous step fails, fallback returning one of the remaining
unassigned address, regardless of its state in the desired list.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-2-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 851bd21cdb ("i3c: master: Fix dynamic address leak when 'assigned-address' is present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16aed0a652 ]
Replace the hardcoded value 2, which indicates 2 bits for I3C address
status, with the predefined macro I3C_ADDR_SLOT_STATUS_BITS.
Improve maintainability and extensibility of the code.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-1-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 851bd21cdb ("i3c: master: Fix dynamic address leak when 'assigned-address' is present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aef79e189b ]
According to I3C spec 6.2 Timing Specification, the Open Drain High Period
of SCL Clock timing for first broadcast address should be adjusted to 200ns
at least. I3C device working as i2c device will see the broadcast to close
its Spike Filter then change to work at I3C mode. After that I3C open drain
SCL high level should be adjusted back.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240910051626.4052552-1-carlos.song@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 25bc99be5f ("i3c: master: svc: Modify enabled_events bit 7:0 to act as IBI enable counter")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 317bacf960 ]
Add hotjoin entry in sys file system allow user enable/disable hotjoin
feature.
Add (*enable(disable)_hotjoin)() to i3c_master_controller_ops.
Add api i3c_master_enable(disable)_hotjoin();
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 25bc99be5f ("i3c: master: svc: Modify enabled_events bit 7:0 to act as IBI enable counter")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cab63f6488 ]
put_device() needs to be called on failure of device_register()
to give up the reference initialized in it to avoid refcount leak.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20230921082410.25548-1-dinghao.liu@zju.edu.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
When a I3C DT node has a static_addr and an init_dyn_addr,the
init_dyn_addr is reserved in i3c_master_bus_init() and then
the static_addr is reserved in i3c_master_early_i3c_dev_add().
But if the dynamic address is same as static then above
procedure would fail.
Add a check to pass i3c_bus_get_addr_slot_status() when static
and dynamic address are equal.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20230822051938.2852567-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Parse the /aliases node to assign any fixed bus numbers, as is done with
the i2c subsystem. Numbering for non-aliased busses will start after the
highest fixed bus number.
This allows an alias node such as:
aliases {
i3c0 = &bus_a,
i3c4 = &bus_b,
};
to set the numbering for a set of i3c controllers:
/* fixed-numbered bus, assigned "i3c-0" */
bus_a: i3c-master {
};
/* another fixed-numbered bus, assigned "i3c-4" */
bus_b: i3c-master {
};
/* dynamic-numbered bus, likely assigned "i3c-5" */
bus_c: i3c-master {
};
If no i3c device aliases are present, the numbering will stay as-is,
starting from 0.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230405094149.1513209-1-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function returned zero unconditionally. Switch the return type to void
and simplify the callers accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230318233311.265186-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- transfer pid from boardinfo to device info
Drivers:
- dw-i3c-master: stop hardcoding initial speed
-----BEGIN PGP SIGNATURE-----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=CEs9
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Subsystem:
- transfer pid from boardinfo to device info
Drivers:
- dw-i3c-master: stop hardcoding initial speed"
* tag 'i3c/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw: stop hardcoding initial speed
i3c: transfer pid from boardinfo to device info
I3C device PID could be defined in device tree and stored in
i3c_dev_boardinfo. It should be passed to i3c_device_info when
allocating a i3c_dev_desc.
Rational behind this change is: when users decide to use SETDASA to
assign a dynamic address with exactly the original static address, in
step of i3c_master_reattach_i3c_dev, this address is checked to be
taken. Then device information retrieving step is skipped. As a result,
though the i3c device is registered correctly, its device driver could
not be probed.
Tested: Tested with a I3C device. If assigned-address is set to be the
device's static address, without this change, its device driver could
not probed. And with this change, its driver is probed successfully.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20230105212952.56321-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because not all I3C drivers have the hot-join feature ready, and
especially not all I3C devices support hot-join feature, exporting
SETDASA method could be useful. With this function, the I3C controller
could perform a DAA to I3C devices when users decide to turn these I3C
devices off and on again during run-time.
Tested: This change has been tested with turnning off an I3C device and
turning on it again during run-time. The device driver calls SETDASA
method to perform DAA to the device. And communication between I3C
controller and device is set up again correctly.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20221207205059.3848851-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The reattach should be used when an I3C device has its address changed.
But the modified place in this patch doesn't have the address changed of
the newdev. This wrong reattach will reserve the same address slot twice
and return unexpected -EBUSY when the bus find the duplicate device with
diffent dynamic address.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20220926105145.8145-2-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch is used to free the old_dyn_addr when the caller want to
reattach the device to the different dynamic address. If the
old_dyn_addr is 0 the function will treat it as no old_dyn_addr is
reserved on the bus. Without the patch, when the driver reattach the i3c
device after setnewda the old_dyn_addr will be permanently occupied.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20220926105145.8145-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Commit 31b9887c72 ("i3c: remove i2c board info from i2c_dev_desc")
removed the boardinfo from i2c_dev_desc to decouple device enumeration from
setup but did not correctly lookup the i2c_dev_desc to store the new
device, instead dereferencing an uninitialized variable.
Lookup the device that has already been registered by address to store
the i2c client device.
Fixes: 31b9887c72 ("i3c: remove i2c board info from i2c_dev_desc")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220308134226.1042367-1-quic_jiles@quicinc.com
I2C devices can be added to the system dynamically through several
sources other than static board info including device tree overlays and
sysfs i2c new_device.
Add an I2C bus notifier to attach the clients at runtime if they were
not defined in the board info. For DT devices find the LVR in the reg
property, for user-space new_device additions we synthesize a
conservative setting of no spike filters and fast mode only.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220117174816.1963463-3-quic_jiles@quicinc.com
I2C board info is only required during adapter setup so there is no
requirement to keeping a pointer to it once running. To support dynamic
device addition we can't rely on board info - user-space creation
through sysfs won't have a boardinfo.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220117174816.1963463-2-quic_jiles@quicinc.com
The address slot bitmap is an array of unsigned long's which are the
same size as an int on 32-bit platforms but not 64-bit. Loading the
bitmap into an int could result in the incorrect status being returned
for a slot and slots being reported as the wrong status.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210922165600.179394-1-quic_jiles@quicinc.com
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of struct bus_type::remove()
because there is only little that can be done. To simplify the quest to
make this function return void, let struct i3c_driver::remove() return
void, too. This makes it obvious that returning an error code is
a bad idea and future driver authors cannot get that wrong.
Up to now there are no drivers with a remove callback, so there is no
need to adapt drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210128091048.17006-2-u.kleine-koenig@pengutronix.de
A registered driver without a probe callback doesn't make sense, so
refuse to register such a driver. (Otherwise i3c_device_probe() yields a
NULL pointer exception.)
A driver without remove is possible, e.g. when all resources are freed
using devm callbacks. So guard the call to driver->remove by a check
for being non-NULL.
Note that the only in-tree i3c driver
(drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i3c.c) doesn't have a remove
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210128091048.17006-1-u.kleine-koenig@pengutronix.de
This patch fix following issue.
Controller slots blocked for devices with static_addr
but no init_dyn_addr may limit the number of I3C devices
on the bus which gets dynamic address in DAA. So
instead of attaching all the devices with static_addr,
now we only attach the devices which successfully
complete SETDASA. For remaining devices with init_dyn_addr,
i3c_master_add_i3c_dev_locked() will try to set requested
dynamic address after DAA.
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/1598337109-14770-1-git-send-email-pthombar@cadence.com
Boardinfo was lost if I3C object for devices with boardinfo
available are not created or not added to the I3C device list
because of some failure e.g. SETDASA failed, retrieve info failed etc
This patch adds i3c_master_attach_boardinfo which scan boardinfo list
in the master object and 'attach' it to the I3C device object.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/1590053542-389-1-git-send-email-pthombar@cadence.com
According to the I3C spec v1.1 document, GETMRL's payload is 2 bytes,
with an optional 3rd byte if the IBI private payload is larger than
1 byte. The whole GETMRL may also be optional so max_ibi_len already
defaults to 1 if BCR_IBI_PAYLOAD prior to the i3c_master_getmrl_locked()
call.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/nycvar.YSQ.7.76.2004151623060.2671@knanqh.ubzr
We already have the master device in a variable, reuse it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/20200214145853.24762-1-wsa+renesas@sang-engineering.com
i3c_bus_set_mode function is only used in master.c.
Make it static to avoid warning when compiling with W=1.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Since we have i3c_dev_get_master() available, use it.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Since we have dev_to_i3cmaster() available, use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
In i3c_master_getmwl_locked(), the buffer used for the dest payload data is
allocated using kzalloc() in i3c_ccc_cmd_dest_init(). Later on, the length
of the dest payload data is checked against 'sizeof(*mwl)'. If they are not
equal, -EIO is returned to indicate the error. However, the allocated
buffer is not deallocated on this path, leading to a memory leak.
To fix the above issue, free the buffer before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
I need to store address and lvr value for I2C devices without static definition
in DT. This allows secondary master to transmit DEFSLVS command properly.
Main changes between v4 and v5:
- Change in defslvs to use addr and lvr from i2c_dev_desc structure
- Change in CDNS and DW drivers to use addr and lvr from i2c_dev_desc structure
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Each iteration of for_each_available_childe_of_node puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Some I3C device drivers need to know which entry matches the
i3c_device object passed to the probe function
Let's move i3c_device_match_id() to device.c and export it so it can be
used by drivers.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(*defslvs) + ((ndevs - 1) * sizeof(struct i3c_ccc_dev_desc))
with:
struct_size(defslvs, slaves, ndevs - 1)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The i3c bus spec defines a bus configuration where i2c devices don't
have a 50ns filter but support SCL running at SDR max rate (12.5MHz).
This patch introduces the limited bus mode so that users can use
a higher speed in presence of i2c devices index 1.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Currently the I3C framework limits SCL frequency to FM speed when
dealing with a mixed slow bus, even if all I2C devices are FM+ capable.
The core was also not accounting for I3C speed limitations when
operating in mixed slow mode and was erroneously using FM+ speed as the
max I2C speed when operating in mixed fast mode.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This patch drops support for I2C devices with 10 bit addressing. When I2C
device with 10 bit address is defined in DT, I3C master registration fails.
Address space for I2C devices has been reduced and ->i2c_funcs() hook has been
removed.
Because this patch series dropped support for 10 bit I2C devices, support is
also dropped in Cadence I3C master driver and Synopsys DesignWare I3C master
driver.
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
* Remove dead code in the DW driver
-----BEGIN PGP SIGNATURE-----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=/U9S
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c update from Boris Brezillon:
- Fix a shift wrap bug in the core
- Remove dead code in the DW driver
* tag 'i3c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: Fix a shift wrap bug in i3c_bus_set_addr_slot_status()
i3c: master: dw: remove dead code from dw_i3c_master_*_xfers()
The problem here is that addr can be I3C_BROADCAST_ADDR (126). That
means we're shifting by (126 * 2) % 64 which is 60. The
I3C_ADDR_SLOT_STATUS_MASK is an enum which is an unsigned int in GCC
so shifts greater than 31 are undefined.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
