This updates to 3.10.17-1.0.1 kernel and fixes the GPIO pins behavior
which had no SION flags enabled so not allowing reading back the
setted value of the pin.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This update contains a few important fixes for Nitrogen6x,
Nitrogen6x-SOM, and SABRE Lite:
- bed3f6a3 - Fix for WiFi on Nitrogen6x-SOM carrier board
- 496650f2 - Fix for OV5640 MIPI camera on Nitrogen6x
- 46875533 - Fix for OV5640 MIPI camera on SABRE Lite
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Updates in this release include:
- update Broadcom driver to support per-chip firmware files
(see commit 5ee7d28 in meta-fsl-arm-extra)
- add support for ADV7391 Composite/Component Video output driver
- backport PCIe fixes from mainline kernel
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Includes support for UART3 and UART5.
Signed-off-by: Alex de Cabo <alejandro.de-cabo-garcia@congatec.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Linux kernel 3.0.35 is not longer used, due to that, recipe, patches
and configuration files are removed.
Signed-off-by: Alex de Cabo <alejandro.de-cabo-garcia@congatec.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Provides the recipe and defconfig to 3.10.17 Linux kernel
Signed-off-by: Alex de Cabo <alejandro.de-cabo-garcia@congatec.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Updates in this release include:
- rebase on Freescale 3.10.17_1.0.1_ga release
- support for new (custom) boards
- fixes for production version of Nitrogen6 Max board
- fixes to allow shutdown/restart of WL12xx Wi-Fi
- added support for adv7180 NTSC video input driver
- added support for Gennum GS2971 SDI receiver
- added Ilitek 210x touch screen driver
- update Focaltech ft5x06 touch screen to support 12 touches
- update flexcan driver to allow use with only a standby GPIO
- add support for "disable_giga" parameter for FEC Gb ethernet driver
- add support for SC16IS7XX I2C multi-port serial controller
- add support for "TRULY-1U" display
- add support for Wolfson WM5102 audio codec
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This is the new SolidRun supported kernel for the HummingBoard and
CuBox-i devices. It is based on the Linaro 3.14 kernel releases.
Some of the changes are:
* devicetree files are used now
* zImage is used instead of uImage
* large amounts of memory leak and stability fixes
* increased FEC ethernet performance, higher than the Freescale rated
470 Mbps
* SDHC patchset for better UHS-I support
* residue support for SDMA with FSL's custom firmware integrated to work
with HDMI and optical SPDIF
* higher DMA and GPU efficiency in general
* the vast array of improvements of a 3.14.14 kernel over a 3.0.35 one
Change-Id: I8f5292b3c2951e7fc48dd20e556da1beba092ed5
Signed-off-by: Carlos Rafael Giani <dv@pseudoterminal.org>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This includes the following changes, the defconfig
changes are reflected in the yocto defconfigs to
keep things in sync.
Eric Nelson (39):
nit6xlite_defconfig: add LEDS_GPIO
sabrelite: configure ethernet PHY nRST
nitrogen6x: configure ethernet PHY nRST
nitrogen6_mtp: configure ethernet PHY nRST
nitrogen6_max: configure ethernet PHY nRST
nit6xlite: configure ethernet PHY nRST
nit6xlite: default to multi-touch input for eGalax, ft5x06
nitrogen6x: default to multi-touch input for eGalax, ft5x06
nitrogen6x_ub: default to multi-touch input for eGalax, ft5x06
ft5x06: free GPIO in _remove
ft5x06: add support for ABS_MT_TRACKING_ID
ft5x06: set MAX_TOUCHES to 12
ft5x06: respect/return tracking id from controller
net: fec: iMX6 FEC does not support half-duplex gigabit
nit*_defconfig: add CONFIG_USB_FUNCTIONFS=m
nit*_defconfig: add CONFIG_USB_SERIAL_GENERIC
nit6xlite: add ili210x touch controller
nitrogen6x: add ili210x touch controller
sabrelite: add ili210x touch controller
nitrogen6_max: add ili210x touch controller
nit6xlite_defconfig: add ILI210X touch screen
nitrogen6x_defconfig: add ILI210X touch screen
ili210x: Allow use with Device Tree
nitrogen6_max: enable FEC ethernet
nitrogen6_max: swap NANDF_CS0/1 (GP6:11/14) for SD3 voltage select, WL IRQ
nitrogen6_max: define ENET_TXD1 as GPIO1:29 for amplifier mute
flexcan: allow use with transceivers that only have standby pin
nitrogen6x: SDIO is 1.8V-only, add flag in DTS
sdhci: Allow platform_set_power callback
sdhci-imx: Add power-gpio support
nitrogen6x: use power-gpio instead of vqmmc-supply to control WL_EN pin
nitrogen6_max: use power-gpio instead of vqmmc-supply to control WL_EN pin
nitrogen6_max: configure voltage-select pin
nit6xlite: flag 1.8v quirk for vqmmc on sdhc2 (WiFi interface)
DT:imx6qdl: Pad SD2_DAT3 should have pull-down
nitrogen6x_defconfig: include LEDS_PWM, SPI_SPIDEV
Add imx6q-sabrelite-nolcd device tree
fec: Add disable_giga parameter to force 10/100 operation
Revert "DT:imx6qdl: Pad SD2_DAT3 should have pull-down"
Ranjani Vaidyanathan (1):
ENGR00318392 ARM:imx6x: Save/restore SCU and some CP15 registers across suspend/resume
Signed-off-by: Christoph Settgast <christoph.settgast@methodpark.de>
Reviewed-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Simon Kuhnle <simon.kuhnle@methodpark.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This fixes following warning, when building other mx5 boards:
,----
| WARNING: Unable to get checksum for linux-denx SRC_URI entry
| defconfig: file could not be found
`----
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Update wandboard defconfig to add support for the Fusion touchscreen, Sunplus
keyboard, and some USB to serial devices
Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Now that kernel 3.0.35 is no longer being updated, and that 3.10.17 is now GA and
supports current GPU libraries, remove linux-wandboard (3.0.35).
Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Upstream changes to the brcmfmac driver require a change to the firmware
file names to match the devid and interface type of the Broadcom chipset.
This also makes it easier for one machine to support multiple chipets in
Yocto.
Signed-off-by: John Weber <rjohnweber@gmail.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The update to the Wandboard Linux kernel includes the following changes:
- wandboard_defconfig: Enable CONFIG_USB_OTG
- wandboard/dts: Fix USB OTG
- wand-rfkill: Change gpio depending on wandboard revision
- wandboard: dts: Add alternate pin support for rev C1
- brcmfmac: Use fw filename and nvram based of devid for sdio.
- wandboard: add revision detect pin to rfkill driver
- wandboard/dts: change EDM gpio to open drain
- wandboard/dts: Enable lcdif in devicetree
- wandboard/dts: add fusion touchscreen to devicetree
- wandboard: Fix bluetooth
Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Updates in this release include:
- Configures GPIOs on Nitrogen6_Lite as "gpio-led" devices
- Updates to nit6xlite_defconfig to match nitrogen6x_defconfig
- Added support for Okaya 480x272 display
- Allows concurrent operation of OV5640 MIPI and OV5642 parallel
cameras
Signed-off-by: Christoph Settgast <christoph.settgast@methodpark.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Christoph Settgast <christoph.settgast@methodpark.de>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This patch update the revision to 6fc170bb7b and corrects the following -
1. SUMMARY field. The kernel forks Boundary Devices BSP 4.1.0 but it's
Freescale BSP 4.1.0 as-is.
2. CONFIG_MACH_C1 becomes CONFIG_MACH_HB. Carrier-one was renamed to be HummingBoard.
3. Following two patches not needed anymore since they are part of the kernel -
0002-ARM-7668-1-fix-memset-related-crashes-caused-by-rece.patch
0003-ARM-7670-1-fix-the-memset-fix.patch
Change-Id: I34657245890dc4200592b58a6289ba90a7e9df2c
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
- Added TC358743 HDMI input driver (via MIPI)
- Fix RTC on nitrogen6x/6x-lite to kick-start on power-fail
- Fix UART3 baud-rate mismatch bug
- Update HDMI driver to default to "only CEA modes"
- Fix SGTL5000 issue with reboot
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
- Lots of additional (custom) boards
- Fixes for Focaltech ft5x06 touch screen (10-points now)
- RS-485 half-duplex and Rx/Tx LED support
- Added fake power-down to blank displays during power-off
- Added TC358743 HDMI input driver (via MIPI)
- Added GS2971 driver (via CSI)
- Fix RTC on nitrogen6x/6x-lite to kick-start on power-fail
- Fix UART3 baud-rate mismatch bug
- Update HDMI driver to default to "only CEA modes"
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Update defconfig files for Boundary Devices' boards to include
- Updates for SystemD support
- Use 3G/1G split
- Add support for various USB->serial adapters
- Add g_mass_storage (=m)
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Update defconfig files for Boundary Devices' boards to include
- Updates for SystemD support
- Use 3G/1G split
- Add support for various USB->serial adapters
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This kernel setting is required when using systemd >= 210. Without
it, no serial devices are enabled at boot time, making serial login
impossible.
Only tested on SabreLite (Nitrogen6x), but the same change should be
applied to all boards.
Signed-off-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Update Boundary Devices' linux kernel to one based on FSL's 3.10.17_1.0.0_ga
instead of 3.10.17_1.0.0_beta.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Update Wandboard Linux kernel to one based on FSL's 3.10.17_1.0.0_ga. Also,
updated the defconfig to better align with FSL's imx_v7_defconfig where
possible to avoid potential problems
Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Bump the revision to include a workaround for the USB phy issue we are
sometimes seeing.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This removes useless and very verbose debug that would appear e.g. while
plugging a USB stick.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
It can now be found on the original recipe's SUMMARY (on meta-fsl-arm).
Signed-off-by: Mario Domenech Goulart <mario@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Kernel version 3.10 requires lzop to build.
Fix suggested by Erik Botö <erik.boto@pelagicore.com>
Reported-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Replace DESCRIPTION to SUMMARY on linux recipes.
The SUMMARY content may be used in Release Notes to
describe the each kernel provider.
Add SUMMARY for linux-congatec, linux-cubox-i and
linux-timesys. For those, the SUMMARY used was the one
already in Release Notes [1] in file [2]
[1] https://github.com/Freescale/Documentation
[2] release-notes/source/kernel-linux.rst
Signed-off-by: Daiane Angolini <daiane.angolini@freescale.com>
The 3.10.17 version is added automatically by the build process,
so it's not needed in LOCALVERSION.
As Diego reported, without this patch, 'uname -r' and kernel modules
are oddly-named:
/lib/modules/3.10.173.10.17_beta+yocto
Reported-by: Diego <diego.ml@zoho.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Update Wandboard 3.10.17 kernel to commit 4a8ad4, which includes an update
to the DTS to enable all mxcfb devices and a fix for the sgtl5000 driver.
Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This kernel is based on linux-timesys 3.0.15, and adds commits for quartz
support that include:
* Add Display and Resistive Touchscreen support
* Add Quartz Hardware Modules support
* Add additional UART support
* Update i2c settings for Audio driver
* New defconfig (i.e. quartz)
This kernel has been tested on the quartz platform.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The following changes have been made in this version of the kernel:
* Fix for ethernet, which was previously not working.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The only machines using the recipe was imx233-olinuxino ones but those
are defaulting to linux-fslc for a while without failure reports so it
is safe to drop this now.
Change-Id: I86663543c5ee893fb1d0c55defa3d0c68cba85be
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
To easy the maintenance of the kernel for Congatec boards and allow
removal of the 3.0.35 of meta-fsl-arm when desired we include the
needed patches here instead of using a bbappend on top of linux-imx
original recipe.
Change-Id: I5766ba81b514beb1f50f04d8d0e4efcc4d2b5898
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This removes the PRINC which is deprecated and will be removed after
Yocto Project 1.6 release. The 2.6.35.3 and 3.0.35 kernel versions
need to be updated in meta-fsl-arm at same time, to avoid version to
go backwards.
Change-Id: I38dde3b81715e64ce7a9e724b85901d44490c082
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This kernel is based on linux-timesys 3.0.15, and adds commits for pcm052
support that include:
* Add FEC1 support
* Add QSPI NOR support
* Add PWM backlight support
* Enable watchdog
* Fix DCU settings
* New defconfig (i.e. pcm052)
This kernel has been tested on the pcm052 platform.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
This kernel is based on linux-timesys 3.0.15, and adds commits for pcl052
support that include:
* Add HDMI support
* Add LED GPIO support
* Fix DCU multiplier calculation
* Fix USB Gadget
* New defconfig (i.e. pcl052)
This kernel has been tested on the pcl052 platform.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
The 3.10.17-1.0.0 GPU has been updated tp 4.6.9p13 release. This patch
updates the kernel driver to be compatible with it.
Change-Id: Ice6579d97c8488c5e551db5949d3ee3786d50dc9
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
The 3.10.17-1.0.0 GPU has been updated tp 4.6.9p13 release. This patch
updates the kernel driver to be compatible with it.
Change-Id: I6607dd6879e77654d8ac1894eed18ce808eb7e8d
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Several changes to defconfig including:
- Add CONFIG_CFLAGS and CONFIG_FHANDLE to allow for systemd support
- Enable Broadcom drivers by default
- Enable RFKILL support in kernel, this is necessary for Broadcom driver
- Enable user-space view of device tree in /proc/device-tree
Signed-off-by: John Weber <rjohnweber@gmail.com>
The following changes are made:
- Update SRCREV to 95f32b7
- Set the git URI in WANDBOARD_GITHUB_MIRROR to allow overide in
local.conf
Signed-off-by: John Weber <rjohnweber@gmail.com>
The branch, which contains the needed hash, is:
m53evk-rel-2013-05-02-v3.9
Fix the recipe accordingly.
Change-Id: Ie5d7b1f550d0d1ec92f3b4cea89f1b73d069cf32
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Seems "same" changes has been made on both master and dora branch,
but the dora commit has the space in place.
This patch was created via:
git diff freescale/dora..freescale/master recipes-kernel/linux/linux-imx_3.0.35.bbappend | patch -p1 -R
Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
Add missing flags in kernel config.
Namely: CONFIG_USB_EHCI_ARC_H1=y and CONFIG_USB_FSL_ARC_OTG=y
Signed-off-by: Pavel Kopylov <pavel.kopylov@gmail.com>
The compatible machine filter is required to avoid build warnings when
building for other boards, as:
,----[ Build warning ]
| WARNING: Unable to get checksum for linux-boundary
| SRC_URI entry defconfig: file could not be found
`----
Change-Id: I2f55697fbef29c35b332bfdcc5023c5f70bc9e4b
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
