The new U-Boot 2015.07-based release offers support for SPL for
Wandboard. This allows the same image to run in every Wandboard
variant available.
This consolidates the Quad, Dual and Solo variants into a single
Wandboard machine definition.
Change-Id: Icf87301431b48ef857670e1f3a941706a7bfc50d
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Add an entry for cubox-i in order to fix the following build error:
ERROR: Nothing RPROVIDES 'bcm4329-nvram-config' (but /work/yocto/master/sources/poky/meta/recipes-core/packagegroups/packagegroup-base.bb RDEPENDS on or otherwise requires it)
ERROR: bcm4329-nvram-config was skipped: incompatible with machine cubox-i (not in COMPATIBLE_MACHINE)
Also add the brcmfmac4329-sdio.txt file for cubox-i.
Change-Id: I91797c9122c97b2e17b780c5b5f523f9aa4edae3
Reported-by: Peter Bergin <peter.bergin@tritech.se>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Remove extra blank lines in the end of the sdio.txt files.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The imx6sl-warp board has a bcm4330 chip, so enable the nvram
configuration to allow the WiFi to work out of box.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The cubox-i board has a bcm4330 chip. This enables the nvram
configuration to allow the WiFi to work out of box.
Change-Id: I4b7ba516083c9f24c55ede8da49dd9ba7be4a31b
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Upstream driver changes cause the driver to request firmware based on
the device ID (e.g. 4329, 4330). This also applies to the nvram config
file. Restructure the recipes and separate by chipset.
Modify conf/machine to use chipset-specific broadcom nvram packages
Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The Nitrogen6-Lite board supports Wi-fi with a daughterboard
with the Broadcom 4330 ABGN chip.
This patch adds the driver, firmware, and calibration (nvram)
files to the build using the broadcom-nvram-config recipe.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
This avoid a warning, during recipe parsing of bitbake, due an
incompatible machine as the nvram.txt is not available as no know
default one is suitable for every board so a specific one is need.
Change-Id: I409a1310c6f37975a46d79cdbd84665daa381e0d
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add a recipe to provide an nvram file required by certain Broadcom wifi
chips. This file is machine-specific.
Files are installed at /lib/firmware/brcm.
Signed-off-by: John Weber <rjohnweber@gmail.com>
