* update SRC_URI format to use the same as linux-raspberrypi_5.10.bb
and linux-raspberrypi_5.4.bb by dropping protocol=git and using
LINUX_RPI_KMETA_BRANCH
* protocol=git was dropped from other linux-raspberrypi recipes in:
commit 0381ac4d08
Author: Timm Eversmeyer <saeugetier@googlemail.com>
Date: Wed Sep 11 07:08:50 2019 +0200
raspberrypi-linux: removed protocoll setting from SRC_URI
Default protocoll for git will be used. Default setting is in the most case https.
Signed-off-by: Timm Eversmeyer saeugetier@gmail.com
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
master can only be validated with latest WIP oe-core releases so drop
gatesgrath which is now a dedicated release, soon hardknott will be out
too but for master needs its fine, while hear add honister ( fall 2021 )
release too
Signed-off-by: Khem Raj <raj.khem@gmail.com>
overlay_map.dtb arranges that when config.txt requests "vc4-kms-v3d"
the rpi4 will actually load "vc4-kms-v3d-pi4" and fixups like that.
It is present on the official distros, and must be put into the
overlays subdirectory in the boot partition.
For a detailed description of the overlay_map.dts file see:
https://www.raspberrypi.org/documentation/configuration/device-tree.md#part2.2.10
vc4-kms-v3d-pi4 is required for the arm based kms driver on the rpi4.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
This fixes, amongst others, issues with I2C controller interrupts on the RPI4
that prevented a touch panel from functioning.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
* raspberrypi4-64 is 15 characters and with dosfstools-4.2 it breaks rootfs.rpi-sdimg with:
mkfs.vfat: Label can be no longer than 11 characters
mkfs.fat 4.2 (2021-01-31)
* introduced in:
https://github.com/dosfstools/dosfstools/commit/c598354
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
In theory, this would allow one to use the official 7-inch touchscreen
in combination with the (non-firmware) kms driver by adding the
following lines to config.txt:
ignore_lcd=1
dtoverlay=vc4-kms-v3d
dtoverlay=vc4-kms-dsi-7inch
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
It has prebuilt binary libgpiod_pulsein for rpi machines and these binary is 32bit
therefore we can not include it for 64bit machines even if they are rpi
based unless they have multilib enabled.
This patch makes it visible only on 32bit rpi
Fixes QA errors like
ERROR: QA Issue: Architecture did not match (ARM, expected AArch64) in /usr/lib/python3.9/site-packages/adafruit_blinka/microcontroller/bcm283x/pulseio/.debug/libgpiod_pulsein [arch]
Signed-off-by: Khem Raj <raj.khem@gmail.com>
https://github.com/agherzan/meta-raspberrypi/pull/815
introduced python3-adafruit-blinka and this recipe has added rdep on rpi-gpio,
however rpi-gpio is rpi specific package, and therefore should only be added
when building rpi based platforms, this makes the layer work in a
multi-bsp setup work
Signed-off-by: Khem Raj <raj.khem@gmail.com>
gstreamer1.0-omx receipe on OE-core sets:
core-name=${GSTREAMER_1_0_OMX_CORE_NAME} on the installed gstomx.conf
in this case it will set:
core-name="${libdir}/libopenmaxil.so" in ${sysconfdir}/xdg/gstomx.conf
this is done in set_omx_core_name that is a do_install[postfuncs]
Signed-off-by: Jose Quaresma <quaresma.jose@gmail.com>
With current recipe formatting CMDLINE variable contains
many unnecessary white spaces. This patch allow to drop
unnecessary spaces at the moment of writing them to
cmdline.txt. This will improve readability of cmdline.txt,
/proc/cmdline and dmesg output.
Signed-off-by: Bartłomiej Burdukiewicz <bartlomiej.burdukiewicz@gmail.com>
By default in case of CM4 IO board, the USB ports (header + built-in)
are disabled. In order to enable them the DWC2 mode needs to be set to
host.
Signed-off-by: Aurelian Zanoschi <aurelian17@gmail.com>
Currently, the do_compile log is cluttered with dtc warnings that should only
be printed when compiling with W="123":
...
/soc: node has a reg or ranges property, but no unit name
/soc/gpu: missing or empty reg/ranges property
/soc/firmware/gpio: missing or empty reg/ranges property
...
This happens because we pass dtc flags via KERNEL_EXTRA_ARGS directly on the
make command line, preventing scripts/Makefile.lib logic from appending flags
that silence dtc warnings (all assignments done from within a makefile, to a
variable specified on the command line, are ignored).
oe-core commit [1] introduced the dedicated KERNEL_DTC_FLAGS variable to pass
dtc flags via the environment. Use this variable to get rid of the do_compile
log noise.
The md5sums of the generated dtbs for raspberrypi3-64 and raspberrypi4-64 do
not change with this patch applied.
[1] https://github.com/openembedded/openembedded-core/commit/063b5de86624
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
