[ Upstream commit 816be86c79 ]
qc->result_tf contents are only valid when the ATA_QCFLAG_RTF_FILLED flag
is set. The ATA_QCFLAG_RTF_FILLED flag should be always set for commands
that failed or for commands that have the ATA_QCFLAG_RESULT_TF flag set.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-8-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f6d903b54 ]
SCSI layer clears sense_buffer in scsi_queue_rq() so there is no need for
libata to clear it again.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-5-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4bc0a264f ]
The overflow/underflow conditions in pata_macio_qc_prep() should never
happen. But if they do there's no need to kill the system entirely, a
WARN and failing the IO request should be sufficient and might allow the
system to keep running.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 284b75a3d8 upstream.
In ata_host_alloc(), if devres_alloc() fails to allocate the device host
resource data pointer, the already allocated ata_host structure is not
freed before returning from the function. This results in a potential
memory leak.
Call kfree(host) before jumping to the error handling path to ensure
that the ata_host structure is properly freed if devres_alloc() fails.
Fixes: 2623c7a5f2 ("libata: add refcounting to ata_host")
Cc: stable@vger.kernel.org
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa0db8e568 upstream.
This reverts commit 28ab976911.
Sense data can be in either fixed format or descriptor format.
SAT-6 revision 1, "10.4.6 Control mode page", defines the D_SENSE bit:
"The SATL shall support this bit as defined in SPC-5 with the following
exception: if the D_ SENSE bit is set to zero (i.e., fixed format sense
data), then the SATL should return fixed format sense data for ATA
PASS-THROUGH commands."
The libata SATL has always kept D_SENSE set to zero by default. (It is
however possible to change the value using a MODE SELECT SG_IO command.)
Failed ATA PASS-THROUGH commands correctly respected the D_SENSE bit,
however, successful ATA PASS-THROUGH commands incorrectly returned the
sense data in descriptor format (regardless of the D_SENSE bit).
Commit 28ab976911 ("ata: libata-scsi: Honor the D_SENSE bit for
CK_COND=1 and no error") fixed this bug for successful ATA PASS-THROUGH
commands.
However, after commit 28ab976911 ("ata: libata-scsi: Honor the D_SENSE
bit for CK_COND=1 and no error"), there were bug reports that hdparm,
hddtemp, and udisks were no longer working as expected.
These applications incorrectly assume the returned sense data is in
descriptor format, without even looking at the RESPONSE CODE field in the
returned sense data (to see which format the returned sense data is in).
Considering that there will be broken versions of these applications around
roughly forever, we are stuck with being bug compatible with older kernels.
Cc: stable@vger.kernel.org # 4.19+
Reported-by: Stephan Eisvogel <eisvogel@seitics.de>
Reported-by: Christian Heusel <christian@heusel.eu>
Closes: https://lore.kernel.org/linux-ide/0bf3f2f0-0fc6-4ba5-a420-c0874ef82d64@heusel.eu/
Fixes: 28ab976911 ("ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240813131900.1285842-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28ab976911 upstream.
SAT-5 revision 8 specification removed the text about the ANSI INCITS
431-2007 compliance which was requiring SCSI/ATA Translation (SAT) to
return descriptor format sense data for the ATA PASS-THROUGH commands
regardless of the setting of the D_SENSE bit.
Let's honor the D_SENSE bit for ATA PASS-THROUGH commands while
generating the "ATA PASS-THROUGH INFORMATION AVAILABLE" sense data.
SAT-5 revision 7
================
12.2.2.8 Fixed format sense data
Table 212 shows the fields returned in the fixed format sense data
(see SPC-5) for ATA PASS-THROUGH commands. SATLs compliant with ANSI
INCITS 431-2007, SCSI/ATA Translation (SAT) return descriptor format
sense data for the ATA PASS-THROUGH commands regardless of the setting
of the D_SENSE bit.
SAT-5 revision 8
================
12.2.2.8 Fixed format sense data
Table 211 shows the fields returned in the fixed format sense data
(see SPC-5) for ATA PASS-THROUGH commands.
Cc: stable@vger.kernel.org # 4.19+
Reported-by: Niklas Cassel <cassel@kernel.org>
Closes: https://lore.kernel.org/linux-ide/Zn1WUhmLglM4iais@ryzen.lan
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240702024735.1152293-4-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9798192622 upstream.
Current ata_gen_passthru_sense() code performs two actions:
1. Generates sense data based on the ATA 'status' and ATA 'error' fields.
2. Populates "ATA Status Return sense data descriptor" / "Fixed format
sense data" with ATA taskfile fields.
The problem is that #1 generates sense data even when a valid sense data
is already present (ATA_QCFLAG_SENSE_VALID is set). Factoring out #2 into
a separate function allows us to generate sense data only when there is
no valid sense data (ATA_QCFLAG_SENSE_VALID is not set).
As a bonus, we can now delete a FIXME comment in atapi_qc_complete()
which states that we don't want to translate taskfile registers into
sense descriptors for ATAPI.
Additionally, always set SAM_STAT_CHECK_CONDITION when CK_COND=1 because
SAT specification mandates that SATL shall return CHECK CONDITION if
the CK_COND bit is set.
The ATA PASS-THROUGH handling logic in ata_scsi_qc_complete() is hard
to read/understand. Improve the readability of the code by moving checks
into self-explanatory boolean variables.
Cc: stable@vger.kernel.org # 4.19+
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-3-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38dab832c3 upstream.
Correct the ATA PASS-THROUGH fixed format sense data offsets to conform
to SPC-6 and SAT-5 specifications. Additionally, set the VALID bit to
indicate that the INFORMATION field contains valid information.
INFORMATION
===========
SAT-5 Table 212 — "Fixed format sense data INFORMATION field for the ATA
PASS-THROUGH commands" defines the following format:
+------+------------+
| Byte | Field |
+------+------------+
| 0 | ERROR |
| 1 | STATUS |
| 2 | DEVICE |
| 3 | COUNT(7:0) |
+------+------------+
SPC-6 Table 48 - "Fixed format sense data" specifies that the INFORMATION
field starts at byte 3 in sense buffer resulting in the following offsets
for the ATA PASS-THROUGH commands:
+------------+-------------------------+
| Field | Offset in sense buffer |
+------------+-------------------------+
| ERROR | 3 |
| STATUS | 4 |
| DEVICE | 5 |
| COUNT(7:0) | 6 |
+------------+-------------------------+
COMMAND-SPECIFIC INFORMATION
============================
SAT-5 Table 213 - "Fixed format sense data COMMAND-SPECIFIC INFORMATION
field for ATA PASS-THROUGH" defines the following format:
+------+-------------------+
| Byte | Field |
+------+-------------------+
| 0 | FLAGS | LOG INDEX |
| 1 | LBA (7:0) |
| 2 | LBA (15:8) |
| 3 | LBA (23:16) |
+------+-------------------+
SPC-6 Table 48 - "Fixed format sense data" specifies that
the COMMAND-SPECIFIC-INFORMATION field starts at byte 8
in sense buffer resulting in the following offsets for
the ATA PASS-THROUGH commands:
Offsets of these fields in the fixed sense format are as follows:
+-------------------+-------------------------+
| Field | Offset in sense buffer |
+-------------------+-------------------------+
| FLAGS | LOG INDEX | 8 |
| LBA (7:0) | 9 |
| LBA (15:8) | 10 |
| LBA (23:16) | 11 |
+-------------------+-------------------------+
Reported-by: Akshat Jain <akshatzen@google.com>
Fixes: 11093cb1ef ("libata-scsi: generate correct ATA pass-through sense")
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-2-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eeb25a09c5 upstream.
.probe() (ahci_init_one()) calls sysfs_add_file_to_group(), however,
if probe() fails after this call, we currently never call
sysfs_remove_file_from_group().
(The sysfs_remove_file_from_group() call in .remove() (ahci_remove_one())
does not help, as .remove() is not called on .probe() error.)
Thus, if probe() fails after the sysfs_add_file_to_group() call, the next
time we insmod the module we will get:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:04.0/remapped_nvme'
CPU: 11 PID: 954 Comm: modprobe Not tainted 6.10.0-rc5 #43
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
sysfs_warn_dup.cold+0x17/0x23
sysfs_add_file_mode_ns+0x11a/0x130
sysfs_add_file_to_group+0x7e/0xc0
ahci_init_one+0x31f/0xd40 [ahci]
Fixes: 894fba7f43 ("ata: ahci: Add sysfs attribute to show remapped NVMe device count")
Cc: stable@vger.kernel.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240629124210.181537-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6549f538f ]
libsas is currently not freeing all the struct ata_port struct members,
e.g. ncq_sense_buf for a driver supporting Command Duration Limits (CDL).
Add a function, ata_port_free(), that is used to free a ata_port,
including its struct members. It makes sense to keep the code related to
freeing a ata_port in its own function, which will also free all the
struct members of struct ata_port.
Fixes: 18bd7718b5 ("scsi: ata: libata: Handle completion of CDL commands using policy 0xD")
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240629124210.181537-8-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zdH0
-----END PGP SIGNATURE-----
Merge tag 'v6.6.34' into lf-6.6.y
This is the 6.6.34 stable release
* tag 'v6.6.34': (2530 commits)
Linux 6.6.34
smp: Provide 'setup_max_cpus' definition on UP too
selftests: net: more strict check in net_helper
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
drivers/net/ethernet/freescale/fec_ptp.c
drivers/pmdomain/imx/imx8mp-blk-ctrl.c
drivers/usb/dwc3/host.c
tools/perf/util/pmu.c
commit d4a89339f1 upstream.
Commit defc9cd826 ("pata_legacy: resychronize with upstream changes and
resubmit") missed to update legacy_exit(), so that it now fails to do any
cleanup -- the loop body there can never be entered. Fix that and finally
remove now useless nr_legacy_host variable...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: defc9cd826 ("pata_legacy: resychronize with upstream changes and resubmit")
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e85006ae74 ]
The call to clk_enable() in gemini_sata_start_bridge() can fail.
Add a check to detect such failure.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7933650478 upstream.
Commit 0c76106cb9 ("scsi: sd: Fix TCG OPAL unlock on system resume")
incorrectly handles failures of scsi_resume_device() in
ata_scsi_dev_rescan(), leading to a double call to
spin_unlock_irqrestore() to unlock a device port. Fix this by redefining
the goto labels used in case of errors and only unlock the port
scsi_scan_mutex when scsi_resume_device() fails.
Bug found with the Smatch static checker warning:
drivers/ata/libata-scsi.c:4774 ata_scsi_dev_rescan()
error: double unlocked 'ap->lock' (orig line 4757)
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 0c76106cb9 ("scsi: sd: Fix TCG OPAL unlock on system resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0297e7dd5 upstream.
Even though the command duration limits (CDL) feature was first added
in ACS-5 (major version 12), there are some ACS-4 (major version 11)
drives that implement CDL as well.
IDENTIFY_DEVICE, SUPPORTED_CAPABILITIES, and CURRENT_SETTINGS log pages
are mandatory in the ACS-4 standard so it should be safe to read these
log pages on older drives implementing the ACS-4 standard.
Fixes: 62e4a60e0c ("scsi: ata: libata: Detect support for command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3137b83a90 ]
Building with W=1 shows a warning for an unused variable when CONFIG_PCI
is diabled:
drivers/ata/sata_mv.c:790:35: error: unused variable 'mv_pci_tbl' [-Werror,-Wunused-const-variable]
static const struct pci_device_id mv_pci_tbl[] = {
Move the table into the same block that containsn the pci_driver
definition.
Fixes: 7bb3c5290c ("sata_mv: Remove PCI dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52f80bb181 ]
gcc warns about a memcpy() with overlapping pointers because of an
incorrect size calculation:
In file included from include/linux/string.h:369,
from drivers/ata/sata_sx4.c:66:
In function 'memcpy_fromio',
inlined from 'pdc20621_get_from_dimm.constprop' at drivers/ata/sata_sx4.c:962:2:
include/linux/fortify-string.h:97:33: error: '__builtin_memcpy' accessing 4294934464 bytes at offsets 0 and [16, 16400] overlaps 6442385281 bytes at offset -2147450817 [-Werror=restrict]
97 | #define __underlying_memcpy __builtin_memcpy
| ^
include/linux/fortify-string.h:620:9: note: in expansion of macro '__underlying_memcpy'
620 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
include/linux/fortify-string.h:665:26: note: in expansion of macro '__fortify_memcpy_chk'
665 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
include/asm-generic/io.h:1184:9: note: in expansion of macro 'memcpy'
1184 | memcpy(buffer, __io_virt(addr), size);
| ^~~~~~
The problem here is the overflow of an unsigned 32-bit number to a
negative that gets converted into a signed 'long', keeping a large
positive number.
Replace the complex calculation with a more readable min() variant
that avoids the warning.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0c76106cb9 upstream.
Commit 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop
management") introduced the manage_system_start_stop scsi_device flag to
allow libata to indicate to the SCSI disk driver that nothing should be
done when resuming a disk on system resume. This change turned the
execution of sd_resume() into a no-op for ATA devices on system
resume. While this solved deadlock issues during device resume, this change
also wrongly removed the execution of opal_unlock_from_suspend(). As a
result, devices with TCG OPAL locking enabled remain locked and
inaccessible after a system resume from sleep.
To fix this issue, introduce the SCSI driver resume method and implement it
with the sd_resume() function calling opal_unlock_from_suspend(). The
former sd_resume() function is renamed to sd_resume_common() and modified
to call the new sd_resume() function. For non-ATA devices, this result in
no functional changes.
In order for libata to explicitly execute sd_resume() when a device is
resumed during system restart, the function scsi_resume_device() is
introduced. libata calls this function from the revalidation work executed
on devie resume, a state that is indicated with the new device flag
ATA_DFLAG_RESUMING. Doing so, locked TCG OPAL enabled devices are unlocked
on resume, allowing normal operation.
Fixes: 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop management")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218538
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240319071209.1179257-1-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cd8adc3e1 ]
Previously, patches have been added to limit the reported count of SATA
ports for asm1064 and asm1166 SATA controllers, as those controllers do
report more ports than physically having.
While it is allowed to report more ports than physically having in CAP.NP,
it is not allowed to report more ports than physically having in the PI
(Ports Implemented) register, which is what these HBAs do.
(This is a AHCI spec violation.)
Unfortunately, it seems that the PMP implementation in these ASMedia HBAs
is also violating the AHCI and SATA-IO PMP specification.
What these HBAs do is that they do not report that they support PMP
(CAP.SPM (Supports Port Multiplier) is not set).
Instead, they have decided to add extra "virtual" ports in the PI register
that is used if a port multiplier is connected to any of the physical
ports of the HBA.
Enumerating the devices behind the PMP as specified in the AHCI and
SATA-IO specifications, by using PMP READ and PMP WRITE commands to the
physical ports of the HBA is not possible, you have to use the "virtual"
ports.
This is of course bad, because this gives us no way to detect the device
and vendor ID of the PMP actually connected to the HBA, which means that
we can not apply the proper PMP quirks for the PMP that is connected to
the HBA.
Limiting the port map will thus stop these controllers from working with
SATA Port Multipliers.
This patch reverts both patches for asm1064 and asm1166, so old behavior
is restored and SATA PMP will work again, but it will also reintroduce the
(minutes long) extra boot time for the ASMedia controllers that do not
have a PMP connected (either on the PCIe card itself, or an external PMP).
However, a longer boot time for some, is the lesser evil compared to some
other users not being able to detect their drives at all.
Fixes: 0077a504e1 ("ahci: asm1166: correct count of reported ports")
Fixes: 9815e39617 ("ahci: asm1064: correct count of reported ports")
Cc: stable@vger.kernel.org
Reported-by: Matt <cryptearth@googlemail.com>
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[cassel: rewrote commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 51af8f255b upstream.
ASMedia have confirmed that all ASM106x parts currently listed in
ahci_pci_tbl[] suffer from the 43-bit DMA address limitation that we ran
into on the ASM1061, and therefore, we need to apply the quirk added by
commit 20730e9b27 ("ahci: add 43-bit DMA address quirk for ASMedia
ASM1061 controllers") to the other supported ASM106x parts as well.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-ide/ZbopwKZJAKQRA4Xv@x1-carbon/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: add link to ASMedia confirmation email]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bf6141060 upstream.
Add support for PCIe SATA adapter cards based on Asmedia 2116 controllers.
These cards can provide up to 10 SATA ports on PCIe card.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26c8404e16 ]
Platform clock and phy error resources are not cleaned up in Xilinx GT PHY
error path.
To fix introduce the function ceva_ahci_platform_enable_resources() which
is a customized version of ahci_platform_enable_resources() and inline with
SATA IP programming sequence it does:
- Assert SATA reset
- Program PS GTR phy
- Bring SATA by de-asserting the reset
- Wait for GT lane PLL to be locked
ceva_ahci_platform_enable_resources() is also used in the resume path
as the same SATA programming sequence (as in probe) should be followed.
Also cleanup the mixed usage of ahci_platform_enable_resources() and custom
implementation in the probe function as both are not required.
Fixes: 9a9d3abe24 ("ata: ahci: ceva: Update the driver to support xilinx GT phy")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4b085736e4 upstream.
In ata ata_dev_power_set_standby(), check that the target device is not
sleeping. If it is, there is no need to do anything.
Fixes: aa3998dbeb ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20730e9b27 ]
With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an
ASUSTeK Pro WS WRX80E-SAGE SE WIFI mainboard, a controller hang was
observed that was immediately preceded by the following kernel
messages:
ahci 0000:28:00.0: Using 64-bit DMA addresses
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00000 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00300 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00380 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00400 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00680 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00700 flags=0x0000]
The first message is produced by code in drivers/iommu/dma-iommu.c
which is accompanied by the following comment that seems to apply:
/*
* Try to use all the 32-bit PCI addresses first. The original SAC vs.
* DAC reasoning loses relevance with PCIe, but enough hardware and
* firmware bugs are still lurking out there that it's safest not to
* venture into the 64-bit space until necessary.
*
* If your device goes wrong after seeing the notice then likely either
* its driver is not setting DMA masks accurately, the hardware has
* some inherent bug in handling >32-bit addresses, or not all the
* expected address bits are wired up between the device and the IOMMU.
*/
Asking the ASM1061 on a discrete PCIe card to DMA from I/O virtual
address 0xffffffff00000000 produces the following I/O page faults:
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000000 flags=0x0010]
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000500 flags=0x0010]
Note that the upper 21 bits of the logged DMA address are zero. (When
asking a different PCIe device in the same PCIe slot to DMA to the
same I/O virtual address, we do see all the upper 32 bits of the DMA
address as 1, so this is not an issue with the chipset or IOMMU
configuration on the test system.)
Also, hacking libahci to always set the upper 21 bits of all DMA
addresses to 1 produces no discernible effect on the behavior of the
ASM1061, and mkfs/mount/scrub/etc work as without this hack.
This all strongly suggests that the ASM1061 has a 43 bit DMA address
limit, and this commit therefore adds a quirk to deal with this limit.
This issue probably applies to (some of) the other supported ASMedia
parts as well, but we limit it to the PCI IDs known to refer to
ASM1061 parts, as that's the only part we know for sure to be affected
by this issue at this point.
Link: https://lore.kernel.org/linux-ide/ZaZ2PIpEId-rl6jv@wantstofly.org/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: drop date from error messages in commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0077a504e1 ]
The ASM1166 SATA host controller always reports wrongly,
that it has 32 ports. But in reality, it only has six ports.
This seems to be a hardware issue, as all tested ASM1166
SATA host controllers reports such high count of ports.
Example output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0xffffff3f impl SATA mode.
By adjusting the port_map, the count is limited to six ports.
New output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0x3f impl SATA mode.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=211873
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218346
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b09d7f8fd5 upstream.
It is not always possible to keep a device in the runtime suspended state
when a system level suspend/resume cycle is executed. E.g. for ATA devices
connected to AHCI adapters, system resume resets the ATA ports, which
causes connected devices to spin up. In such case, a runtime suspended disk
will incorrectly be seen with a suspended runtime state because the device
is not resumed by sd_resume_system(). The power state seen by the user is
different than the actual device physical power state.
Fix this issue by introducing the struct scsi_device flag
force_runtime_start_on_system_start. When set, this flag causes
sd_resume_system() to request a runtime resume operation for runtime
suspended devices. This results in the user seeing the device runtime_state
as active after a system resume, thus correctly reflecting the device
physical power state.
Fixes: 9131bff6a9 ("scsi: core: pm: Only runtime resume if necessary")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231120225631.37938-3-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6371be7aeb upstream.
Commit 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop
management") changed the single bit manage_start_stop flag into 2 boolean
fields of the SCSI device structure. Commit 24eca2dce0 ("scsi: sd:
Introduce manage_shutdown device flag") introduced the manage_shutdown
boolean field for the same structure. Together, these 2 commits increase
the size of struct scsi_device by 8 bytes by using booleans instead of
defining the manage_xxx fields as single bit flags, similarly to other
flags of this structure.
Avoid this unnecessary structure size increase and be consistent with the
definition of other flags by reverting the definitions of the manage_xxx
fields as single bit flags.
Fixes: 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop management")
Fixes: 24eca2dce0 ("scsi: sd: Introduce manage_shutdown device flag")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231120225631.37938-2-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6925165ea ]
Add missing error return check for devm_ioport_map() and return the
error if this function call fails.
Fixes: 0d5ff56677 ("libata: convert to iomap")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
errata:
When a read command returns less data than specified in the PRDs (for
example, there are two PRDs for this command, but the device returns a
number of bytes which is less than in the first PRD), the second PRD of
this command is not read out of the PRD FIFO, causing the next command
to use this PRD erroneously.
workaround
- forces sg_tablesize = 1
- modified the sg_io function in block/scsi_ioctl.c to use a 64k buffer
allocated with dma_alloc_coherent during the probe in ahci_imx
- In order to fix the scsi/sata hang, when CD_ROM and HDD are
accessed simultaneously after the workaround is applied.
Do not go to sleep in scsi_eh_handler, when there is host failed.
Upstream kernel mades it const since:
25df73d933 ("scsi: ata: Declare SCSI host templates const")
Remove SCSI host templates const declaration
But i.MX AHCI local driver needs to make it changable, otherwise:
../drivers/ata/ahci_imx.c: In function ‘imx_ahci_probe’:
../drivers/ata/ahci_imx.c:1050:48: error: assignment of member ‘sg_tablesize’ in read-only object
1050 | ahci_platform_sht.sg_tablesize = 1;
| ^
Signed-off-by: Richard Zhu <Richard.Zhu@freescale.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
i.MX8QM has three HSIO PHY instances that can be used as below three
cases.
- A two lanes PCIe_a, a single lane SATA.
- A single lane PCIe_a, a single lane PCIe_b, a single lane SATA.
- A two lanes PCIe_a, a single lane PCIe_b.
Based on the i.MX8Q PCIe PHY driver, refine i.MX8QM SATA support.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
commit: ef6dcf00353b introduces another issue which affect certain disk.
This patch is to remove the cooldown that it at first improved the results
slightly when executing back to back hotplugs, but it may affect certain
disks during boot.
Signed-off-by: Andy Tang <andy.tang@nxp.com>
Information about ERR051238:
Title: SATA PMP Hot Plug Async Notification Not Working
Description: A hot plug on PMP port is communicated to host through
Asynchronous notification using “Set Device Bits” (SDB) FIS which
indicate that change has happened on a port of PMP by setting the
SNotify bit along with “interrupt” and “Notify” bits. The requirement
for a host to support Asynchronous Notification is that it may
generate an interrupt if the Set Device Bits FIS is received.
The SNotification register enables software to be sure that the
interrupt was due to a notification event. In this case the Host
controller doesn't set the SNotify bit due to which the Software
is not aware of the Hotplug event.
This patch creates a polling thread to detect the hotplug event.
Once hotplug event was detected, it sets up the flags and notify
the system to take actions manually.
NOTE:
1. Limit it to spawn only one hotplug thread.
2. Don't let the thread call async_notification twice during
the same hotplug. (add a one-second cooldown)
Signed-off-by: Andy Tang <andy.tang@nxp.com>
Original driver expect a register node with name "sata-ecc"
this node is of 64 bit wide.
In ACPI such nodes can be provided with QWordMemory, but
QWordMemory can not hold DescriptorName more than 4 characters.
Therefore this patch changes platform property retrival based
upon index instead of named.
Signed-off-by: Udit Kumar <udit.kumar@nxp.com>
There is a erratum on lx2160a which is: "SATA link is
going down sometime during sata initialization"
The workaround for it is to reset the lane. This patch
implements this workaround.
This erratum only exists on lx2160 Rev1, will be addressed
on Rev2 and later.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Commit aa3998dbeb ("ata: libata-scsi: Disable scsi device
manage_system_start_stop") change setting the manage_system_start_stop
flag to false for libata managed disks to enable libata internal
management of disk suspend/resume. However, a side effect of this change
is that on system shutdown, disks are no longer being stopped (set to
standby mode with the heads unloaded). While this is not a critical
issue, this unclean shutdown is not recommended and shows up with
increased smart counters (e.g. the unexpected power loss counter
"Unexpect_Power_Loss_Ct").
Instead of defining a shutdown driver method for all ATA adapter
drivers (not all of them define that operation), this patch resolves
this issue by further refining the sd driver start/stop control of disks
using the new flag manage_shutdown. If this new flag is set to true by
a low level driver, the function sd_shutdown() will issue a
START STOP UNIT command with the start argument set to 0 when a disk
needs to be powered off (suspended) on system power off, that is, when
system_state is equal to SYSTEM_POWER_OFF.
Similarly to the other manage_xxx flags, the new manage_shutdown flag is
exposed through sysfs as a read-write device attribute.
To avoid any confusion between manage_shutdown and
manage_system_start_stop, the comments describing these flags in
include/scsi/scsi.h are also improved.
Fixes: aa3998dbeb ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218038
Link: https://lore.kernel.org/all/cd397c88-bf53-4768-9ab8-9d107df9e613@gmail.com/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
fit3 protocol driver does not support accessing IDE control registers
(device control/altstatus). The DOS driver does not use these registers
either (as observed from DOSEMU trace). But the HW seems to be capable
of accessing these registers - I simply tried bit 3 and it works!
The control register is required to properly reset ATAPI devices or
they will be detected only once (after a power cycle).
Tested with EXP Computer CD-865 with MC-1285B EPP cable and
TransDisk 3000.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Some parallel adapters (e.g. EXP Computer MC-1285B EPP Cable) return
bogus values when there's no master device present. This can cause
reset to fail, preventing the lone slave device (such as EXP Computer
CD-865) from working.
Add custom version of wait_after_reset that ignores master failure when
a slave device is present. The custom version is also needed because
the generic ata_sff_wait_after_reset uses direct port I/O for slave
device detection.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
There's a 'x' missing in 0x55 in pata_parport_devchk(), causing the
detection to always fail. Fix it.
Fixes: 246a1c4c6b ("ata: pata_parport: add driver (PARIDE replacement)")
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
A larger than usual set of fixes for 6.6-rc4 due to the unexpected
number of fixes needed to address ATA disks suspend/resume issues.
In more details:
- Add missing additionalProperties on child nodes to the pata-common DT
bindings (Rob).
- Fix handling of the REPORT SUPPORTED OPERATION CODES command to
ignore reserved bits (Niklas).
- Increase port multiplier soft reset timeout to accomodate slow
devices and avoid issues on wakeup (Matthias).
- A couple of minor code fixes to avoid compilation warnings in
libata-core and libata-eh (me).
- Many patches from me to address suspend/resume issues, and in
particular a potential deadlock on resume due to the SCSI disk driver
resume operation not being synchronized with libata EH port resume
handling. This is addressed by changing the scsi disk driver disk
start/stop control to allow libata to execute disk suspend (spin
down) and resume (spin up) on its own during system suspend/resume.
Runtime suspend/resume control remains with the SCSI disk driver.
Other fixes include:
- Fix libata power management request issuing to avoid races.
- Establish a link between ATA ports and SCSI devices to order PM
operations.
- Fix device removal to avoid issues with driver rmmod removal.
- Fix synchronization of libata device rescan and SCSI disk resume
operation.
- Remove libsas PM operations as suspend/resume is handled directly
by the sas controller resume.
- Fix the SCSI disk driver to not issue commands to suspended disks,
thus avoiding potential system lock-up on resume.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCZRbR0gAKCRDdoc3SxdoY
dkArAP9PFTRgsXEwfE7arBXCwQqXj/W0R2KgKug7Fno+SoQLnAD/ZKe2TR50uwxr
9mwYROdMgi50T9ax1RX1jWA0npGXmQg=
=cFzG
-----END PGP SIGNATURE-----
Merge tag 'ata-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fixes from Damien Le Moal:
"A larger than usual set of fixes for 6.6-rc4 due to the unexpected
number of fixes needed to address ATA disks suspend/resume issues.
In more detail:
- Add missing additionalProperties on child nodes to the pata-common
DT bindings (Rob)
- Fix handling of the REPORT SUPPORTED OPERATION CODES command to
ignore reserved bits (Niklas)
- Increase port multiplier soft reset timeout to accomodate slow
devices and avoid issues on wakeup (Matthias)
- A couple of minor code fixes to avoid compilation warnings in
libata-core and libata-eh (me)
- Many patches from me to address suspend/resume issues, and in
particular a potential deadlock on resume due to the SCSI disk
driver resume operation not being synchronized with libata EH port
resume handling.
This is addressed by changing the scsi disk driver disk start/stop
control to allow libata to execute disk suspend (spin down) and
resume (spin up) on its own during system suspend/resume. Runtime
suspend/resume control remains with the SCSI disk driver.
Other fixes include:
- Fix libata power management request issuing to avoid races
- Establish a link between ATA ports and SCSI devices to order PM
operations
- Fix device removal to avoid issues with driver rmmod removal
- Fix synchronization of libata device rescan and SCSI disk resume
operation
- Remove libsas PM operations as suspend/resume is handled
directly by the sas controller resume
- Fix the SCSI disk driver to not issue commands to suspended
disks, thus avoiding potential system lock-up on resume"
* tag 'ata-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-eh: Fix compilation warning in ata_eh_link_report()
ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
scsi: sd: Do not issue commands to suspended disks on shutdown
ata: libata-core: Do not register PM operations for SAS ports
ata: libata-scsi: Fix delayed scsi_rescan_device() execution
scsi: Do not attempt to rescan suspended devices
ata: libata-scsi: Disable scsi device manage_system_start_stop
scsi: sd: Differentiate system and runtime start/stop management
ata: libata-scsi: link ata port and scsi device
ata: libata-core: Fix port and device removal
ata: libata-core: Fix ata_port_request_pm() locking
ata: libata-sata: increase PMP SRST timeout to 10s
ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
dt-bindings: ata: pata-common: Add missing additionalProperties on child nodes
The 6 bytes length of the tries_buf string in ata_eh_link_report() is
too short and results in a gcc compilation warning with W-!:
drivers/ata/libata-eh.c: In function ‘ata_eh_link_report’:
drivers/ata/libata-eh.c:2371:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 4 [-Wformat-truncation=]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~
drivers/ata/libata-eh.c:2371:56: note: directive argument in the range [-2147483648, 4]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~
drivers/ata/libata-eh.c:2371:17: note: ‘snprintf’ output between 4 and 14 bytes into a destination of size 6
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2372 | ap->eh_tries);
| ~~~~~~~~~~~~~
Avoid this warning by increasing the string size to 16B.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The 24 bytes length allocated to the ncq_desc string in
ata_dev_config_lba() for ata_dev_config_ncq() to use is too short,
causing the following gcc compilation warnings when compiling with W=1:
drivers/ata/libata-core.c: In function ‘ata_dev_configure’:
drivers/ata/libata-core.c:2378:56: warning: ‘%d’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 11 [-Wformat-truncation=]
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~
In function ‘ata_dev_config_ncq’,
inlined from ‘ata_dev_config_lba’ at drivers/ata/libata-core.c:2649:8,
inlined from ‘ata_dev_configure’ at drivers/ata/libata-core.c:2952:9:
drivers/ata/libata-core.c:2378:41: note: directive argument in the range [1, 32]
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~~~~~~~~~~~~~~~~~~~~
drivers/ata/libata-core.c:2378:17: note: ‘snprintf’ output between 16 and 31 bytes into a destination of size 24
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2379 | ddepth, aa_desc);
| ~~~~~~~~~~~~~~~~
Avoid these warnings and the potential truncation by changing the size
of the ncq_desc string to 32 characters.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
libsas does its own domain based power management of ports. For such
ports, libata should not use a device type defining power management
operations as executing these operations for suspend/resume in addition
to libsas calls to ata_sas_port_suspend() and ata_sas_port_resume() is
not necessary (and likely dangerous to do, even though problems are not
seen currently).
Introduce the new ata_port_sas_type device_type for ports managed by
libsas. This new device type is used in ata_tport_add() and is defined
without power management operations.
Fixes: 2fcbdcb4c8 ("[SCSI] libata: export ata_port suspend/resume infrastructure for sas")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 6aa0365a3c ("ata: libata-scsi: Avoid deadlock on rescan after
device resume") modified ata_scsi_dev_rescan() to check the scsi device
"is_suspended" power field to ensure that the scsi device associated
with an ATA device is fully resumed when scsi_rescan_device() is
executed. However, this fix is problematic as:
1) It relies on a PM internal field that should not be used without PM
device locking protection.
2) The check for is_suspended and the call to scsi_rescan_device() are
not atomic and a suspend PM event may be triggered between them,
casuing scsi_rescan_device() to be called on a suspended device and
in that function blocking while holding the scsi device lock. This
would deadlock a following resume operation.
These problems can trigger PM deadlocks on resume, especially with
resume operations triggered quickly after or during suspend operations.
E.g., a simple bash script like:
for (( i=0; i<10; i++ )); do
echo "+2 > /sys/class/rtc/rtc0/wakealarm
echo mem > /sys/power/state
done
that triggers a resume 2 seconds after starting suspending a system can
quickly lead to a PM deadlock preventing the system from correctly
resuming.
Fix this by replacing the check on is_suspended with a check on the
return value given by scsi_rescan_device() as that function will fail if
called against a suspended device. Also make sure rescan tasks already
scheduled are first cancelled before suspending an ata port.
Fixes: 6aa0365a3c ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.
For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.
However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.
Commit 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.
Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.
To do this, the following libata helper functions are introduced:
1) ata_dev_power_set_standby():
This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.
For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.
2) ata_dev_power_set_active() and
This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.
For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.
With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.
Fixes: 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
