Regmap cache mechanism is enabled in default. Thus, IO expander wouldn't
handle GPIO set really before resuming back.
But there are cases need to toggle gpio in NO_IRQ stage.
e.g. To align with PCIe specification, PERST# signal connected on the IO
expander must be toggled during PCIe RC's NO_IRQ_RESUME.
Do not enable the regmap cache when IO expander doesn't have the regulator
during system PM. That means the power of IO expander would be kept on,
and the GPIOs of the IO expander can be toggled really during system PM.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Sherry Sun <sherry.sun@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
[ Upstream commit a513552642 ]
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Fixes: 7687a5b0ee ("gpio: modepin: Add driver support for modepin GPIO controller")
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240902115848.904227-1-liaochen4@huawei.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59cba4a0e6 ]
Checking the gdev->mockdev pointer for NULL must be part of the critical
section.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aad4183232 ]
During Linux graceful reboot, the GPIO interrupts are not disabled.
Since the drivers are not removed during graceful reboot,
the logic to call mlxbf3_gpio_irq_disable() is not triggered.
Interrupts that remain enabled can cause issues on subsequent boots.
For example, the mlxbf-gige driver contains PHY logic to bring up the link.
If the gpio-mlxbf3 driver loads first, the mlxbf-gige driver
will use a GPIO interrupt to bring up the link.
Otherwise, it will use polling.
The next time Linux boots and loads the drivers in this order, we encounter the issue:
- mlxbf-gige loads first and uses polling while the GPIO10
interrupt is still enabled from the previous boot. So if
the interrupt triggers, there is nothing to clear it.
- gpio-mlxbf3 loads.
- i2c-mlxbf loads. The interrupt doesn't trigger for I2C
because it is shared with the GPIO interrupt line which
was not cleared.
The solution is to add a shutdown function to the GPIO driver to clear and disable
all interrupts. Also clear the interrupt after disabling it in mlxbf3_gpio_irq_disable().
Fixes: 38a700efc5 ("gpio: mlxbf3: Add gpio driver support")
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240611171509.22151-1-asmaa@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d795848ecc ]
Userspace may trigger a speculative read of an address outside the gpio
descriptor array.
Users can do that by calling gpio_ioctl() with an offset out of range.
Offset is copied from user and then used as an array index to get
the gpio descriptor without sanitization in gpio_device_get_desc().
This change ensures that the offset is sanitized by using
array_index_nospec() to mitigate any possibility of speculative
information leaks.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Link: https://lore.kernel.org/r/20240523085332.1801-1-hagarhem@amazon.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfc6444b57 ]
Ensure that `i2c_lock' is held when setting interrupt latch and mask in
pca953x_irq_bus_sync_unlock() in order to avoid races.
The other (non-probe) call site pca953x_gpio_set_multiple() ensures the
lock is held before calling pca953x_write_regs().
The problem occurred when a request raced against irq_bus_sync_unlock()
approximately once per thousand reboots on an i.MX8MP based system.
* Normal case
0-0022: write register AI|3a {03,02,00,00,01} Input latch P0
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
* Race case
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|08 {03,02,00,00,01} *** Wrong register ***
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Link: https://lore.kernel.org/r/20240620042915.2173-1-ian.ray@gehealthcare.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
vf610_gpio_irq_set_type will be called in the interrupt context,
so can't handle the direction_input callback, because the API
pinctrl_gpio_direction_input() may sleep.
This reverts commit 09d221896b.
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
[ Upstream commit f8d76c2c31 ]
DTS for Nokia N900 incorrectly specifies "active high" polarity for
the reset line, while the chip documentation actually specifies it as
"active low". In the past the driver fudged gpiod API and inverted
the logic internally, but it was changed in d0d89493bf.
Fixes: d0d89493bf ("Input: tsc2004/5 - switch to using generic device properties")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/ZoWXwYtwgJIxi-hD@google.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07798d7bb ]
bgpio_bits must be aligned with the data bus width. For example, on a
32 bit big endian system and we only have 16 GPIOs. If we only assume
bgpio_bits=16 we can never control the GPIO because the base address
is the lowest address.
low address high address
-------------------------------------------------
| byte3 | byte2 | byte1 | byte0 |
-------------------------------------------------
| NaN | NaN | gpio8-15 | gpio0-7 |
-------------------------------------------------
Fixes: 55b2395e4e ("gpio: mmio: handle "ngpios" properly in bgpio_init()")
Fixes: https://github.com/openwrt/openwrt/issues/15739
Reported-by: Mark Mentovai <mark@mentovai.com>
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Suggested-By: Mark Mentovai <mark@mentovai.com>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Lóránd Horváth <lorand.horvath82@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/TYCP286MB089577B47D70F0AB25ABA6F5BCD52@TYCP286MB0895.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3645ffaf2b ]
As it turns out, there is a large number of out-of-tree DTSes (in
OpenWrt project) that used to specify incorrect (active high) polarity
for the Lantiq reset GPIO, so to keep compatibility while they are
being updated a quirk for force the polarity low is needed. Luckily
these old DTSes used nonstandard name for the property ("gpio-reset" vs
"reset-gpios") so the quirk will not hurt if there are any new devices
that need inverted polarity as they can specify the right polarity in
their DTS when using the standard "reset-gpios" property.
Additionally the condition to enable the transition from standard to
non-standard reset GPIO property name was inverted and the replacement
name for the property was not correct. Fix this as well.
Fixes: fbbbcd177a ("gpiolib: of: add quirk for locating reset lines with legacy bindings")
Fixes: 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API")
Reported-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/ZoLpqv1PN08xHioh@google.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9919cce62f ]
linehandle_set_config() behaves badly when direction is not set.
The configuration validation is borrowed from linehandle_create(), where,
to verify the intent of the user, the direction must be set to in order
to effect a change to the electrical configuration of a line. But, when
applied to reconfiguration, that validation does not allow for the unset
direction case, making it possible to clear flags set previously without
specifying the line direction.
Adding to the inconsistency, those changes are not immediately applied by
linehandle_set_config(), but will take effect when the line value is next
get or set.
For example, by requesting a configuration with no flags set, an output
line with GPIOHANDLE_REQUEST_ACTIVE_LOW and GPIOHANDLE_REQUEST_OPEN_DRAIN
requested could have those flags cleared, inverting the sense of the line
and changing the line drive to push-pull on the next line value set.
Ensure the intent of the user by disallowing configurations which do not
have direction set, returning an error to userspace to indicate that the
configuration is invalid.
And, for clarity, use lflags, a local copy of gcnf.flags, throughout when
dealing with the requested flags, rather than a mixture of both.
Fixes: e588bb1eae ("gpio: add new SET_CONFIG ioctl() to gpio chardev")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240626052925.174272-2-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aa9b96e9a ]
Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken
DT due to any error this value can be any. Without this value validation
there can be out of chips->irqs array boundaries access in
davinci_gpio_probe().
Validate the obtained nirq value so that it won't exceed the maximum
number of IRQs per bank.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: eb3744a2dd ("gpio: davinci: Do not assume continuous IRQ numbering")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Link: https://lore.kernel.org/r/20240618144344.16943-1-amishin@t-argos.ru
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=H63O
-----END PGP SIGNATURE-----
Merge tag 'v6.6.35' into lf-6.6.y
This is the 6.6.35 stable release
* tag 'v6.6.35': (268 commits)
Linux 6.6.35
zap_pid_ns_processes: clear TIF_NOTIFY_SIGNAL along with TIF_SIGPENDING
i2c: designware: Fix the functionality flags of the slave-only interface
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
[ Upstream commit 90dd7de4ef ]
The TQMx86 GPIO controller only supports falling and rising edge
triggers, but not both. Fix this by implementing a software both-edge
mode that toggles the edge type after every interrupt.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Co-developed-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/515324f0491c4d44f4ef49f170354aca002d81ef.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08af509efd ]
irq_set_type() should not implicitly unmask the IRQ.
All accesses to the interrupt configuration register are moved to a new
helper tqmx86_gpio_irq_config(). We also introduce the new rule that
accessing irq_type must happen while locked, which will become
significant for fixing EDGE_BOTH handling.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/6aa4f207f77cb58ef64ffb947e91949b0f753ccd.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d6a811b52 ]
The TQMx86 GPIO controller uses the same register address for input and
output data. Reading the register will always return current inputs
rather than the previously set outputs (regardless of the current
direction setting). Therefore, using a RMW pattern does not make sense
when setting output values. Instead, the previously set output register
value needs to be stored as a shadow register.
As there is no reliable way to get the current output values from the
hardware, also initialize all channels to 0, to ensure that stored and
actual output values match. This should usually not have any effect in
practise, as the TQMx86 UEFI sets all outputs to 0 during boot.
Also prepare for extension of the driver to more than 8 GPIOs by using
DECLARE_BITMAP.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/d0555933becd45fa92a85675d26e4d59343ddc01.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zdH0
-----END PGP SIGNATURE-----
Merge tag 'v6.6.34' into lf-6.6.y
This is the 6.6.34 stable release
* tag 'v6.6.34': (2530 commits)
Linux 6.6.34
smp: Provide 'setup_max_cpus' definition on UP too
selftests: net: more strict check in net_helper
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
drivers/net/ethernet/freescale/fec_ptp.c
drivers/pmdomain/imx/imx8mp-blk-ctrl.c
drivers/usb/dwc3/host.c
tools/perf/util/pmu.c
[ Upstream commit adbc49a5a8 ]
Previous patch modified the standard used by acpi_gpiochip_find()
to match device nodes. Using the device node set in gc->gpiodev->d-
ev instead of gc->parent.
However, there is a situation in gpio-dwapb where the GPIO device
driver will set gc->fwnode for each port corresponding to a child
node under a GPIO device, so gc->gpiodev->dev will be assigned the
value of each child node in gpiochip_add_data().
gpio-dwapb.c:
128,31 static int dwapb_gpio_add_port(struct dwapb_gpio *gpio,
struct dwapb_port_property *pp,
unsigned int offs);
port->gc.fwnode = pp->fwnode;
693,39 static int dwapb_gpio_probe;
err = dwapb_gpio_add_port(gpio, &pdata->properties[i], i);
When other drivers request GPIO pin resources through the GPIO device
node provided by ACPI (corresponding to the parent node), the change
of the matching object to gc->gpiodev->dev in acpi_gpiochip_find()
only allows finding the value of each port (child node), resulting
in a failed request.
Reapply the condition of using gc->parent for match in acpi_gpio-
chip_find() in the code can compatible with the problem of gpio-dwapb,
and will not affect the two cases mentioned in the patch:
1. There is no setting for gc->fwnode.
2. The case that depends on using gc->fwnode for match.
Fixes: 5062e4c14b ("gpiolib: acpi: use the fwnode in acpi_gpiochip_find()")
Fixes: 067dbc1ea5 ("gpiolib: acpi: Don't use GPIO chip fwnode in acpi_gpiochip_find()")
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0166b637 ]
If a line is requested with debounce, and that results in debouncing
in software, and the line is subsequently reconfigured to enable edge
detection then the allocation of the kfifo to contain edge events is
overlooked. This results in events being written to and read from an
uninitialised kfifo. Read events are returned to userspace.
Initialise the kfifo in the case where the software debounce is
already active.
Fixes: 65cff70464 ("gpiolib: cdev: support setting debounce")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240510065342.36191-1-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9344e34e79 ]
Store the debounce period for a requested line locally, rather than in
the debounce_period_us field in the gpiolib struct gpio_desc.
Add a global tree of lines containing supplemental line information
to make the debounce period available to be reported by the
GPIO_V2_GET_LINEINFO_IOCTL and the line change notifier.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: ee0166b637 ("gpiolib: cdev: fix uninitialised kfifo")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02f6b0e1ec ]
The use-after-free issue occurs as follows: when the GPIO chip device file
is being closed by invoking gpio_chrdev_release(), watched_lines is freed
by bitmap_free(), but the unregistration of lineinfo_changed_nb notifier
chain failed due to waiting write rwsem. Additionally, one of the GPIO
chip's lines is also in the release process and holds the notifier chain's
read rwsem. Consequently, a race condition leads to the use-after-free of
watched_lines.
Here is the typical stack when issue happened:
[free]
gpio_chrdev_release()
--> bitmap_free(cdev->watched_lines) <-- freed
--> blocking_notifier_chain_unregister()
--> down_write(&nh->rwsem) <-- waiting rwsem
--> __down_write_common()
--> rwsem_down_write_slowpath()
--> schedule_preempt_disabled()
--> schedule()
[use]
st54spi_gpio_dev_release()
--> gpio_free()
--> gpiod_free()
--> gpiod_free_commit()
--> gpiod_line_state_notify()
--> blocking_notifier_call_chain()
--> down_read(&nh->rwsem); <-- held rwsem
--> notifier_call_chain()
--> lineinfo_changed_notify()
--> test_bit(xxxx, cdev->watched_lines) <-- use after free
The side effect of the use-after-free issue is that a GPIO line event is
being generated for userspace where it shouldn't. However, since the chrdev
is being closed, userspace won't have the chance to read that event anyway.
To fix the issue, call the bitmap_free() function after the unregistration
of lineinfo_changed_nb notifier chain.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Link: https://lore.kernel.org/r/20240505141156.2944912-1-quic_zhonhan@quicinc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11baa36d31 ]
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ace0ebe5c9 ]
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c3b532ad3 ]
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d806f474a9 ]
The controller has several register bits describing access control
information for a given GPIO pin. When SCR_SEC_[R|W]EN is unset, it
means we have full read/write access to all the registers for given GPIO
pin. When SCR_SEC[R|W]EN is set, it means we need to further check the
accompanying SCR_SEC_G1[R|W] bit to determine read/write access to all
the registers for given GPIO pin.
This check was previously declaring that a GPIO pin was accessible
only if either of the following conditions were met:
- SCR_SEC_REN + SCR_SEC_WEN both set
or
- SCR_SEC_REN + SCR_SEC_WEN both set and
SCR_SEC_G1R + SCR_SEC_G1W both set
Update the check to properly handle cases where only one of
SCR_SEC_REN or SCR_SEC_WEN is set.
Fixes: b2b56a1632 ("gpio: tegra186: Check GPIO pin permission before access.")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240424095514.24397-1-pshete@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d045025a2 ]
IRQ chip data contains a pointer to the GPIO chip. Luckily we have
the pointers the same, but strictly speaking it's not guaranteed.
Even though, still better to fix this.
Fixes: ccf6fd6dcc ("gpio: merrifield: Introduce GPIO driver to support Merrifield")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Extend the driver to also support the GPIO controller found on the
LS1046AQDS QIXIS CPLD.
For usecases in which the parent device (the QIXIS CPLD) does not define
a regmap for its memory area, create the driver's own regmap which will
get passed to gpio-regmap trough devm_gpio_regmap_register().
In this case, the offset inside of the regmap will be zero since the
regmap points directly to the desired register.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Instead of directly passing the register addresses, use
GPIO_REGMAP_ADDR() so that we also cover the case in which the offset
inside the regmap is zero.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Though the default pin configuration is INPUT, but if the prior stage does
configure the pins as OUTPUT, then Linux will not reconfigure the pin as
INPUT. If use this pin as interrupt source, and set as low level trigger,
if prior stage set this pin as OUTPUT low, then will meet interrupt storm.
So always set GPIO to input mode when used as interrupt source to fix above
case.
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
commit 83092341e1 upstream.
When adding sanitization of the label, the path through
edge_detector_setup() that leads to debounce_setup() was overlooked.
A request taking this path does not allocate a new label and the
request label is freed twice when the request is released, resulting
in memory corruption.
Add label sanitization to debounce_setup().
Cc: stable@vger.kernel.org
Fixes: b34490879b ("gpio: cdev: sanitize the label before requesting the interrupt")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
[Bartosz: rebased on top of the fix for empty GPIO labels]
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3b9596459 upstream.
We need to take into account that a line's consumer label may be NULL
and not try to kstrdup() it in that case but rather pass the NULL
pointer up the stack to the interrupt request function.
To that end: let make_irq_label() return NULL as a valid return value
and use ERR_PTR() instead to signal an allocation failure to callers.
Cc: stable@vger.kernel.org
Fixes: b34490879b ("gpio: cdev: sanitize the label before requesting the interrupt")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/lkml/20240402093534.212283-1-naresh.kamboju@linaro.org/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b34490879b upstream.
When an interrupt is requested, a procfs directory is created under
"/proc/irq/<irqnum>/<label>" where <label> is the string passed to one of
the request_irq() variants.
What follows is that the string must not contain the "/" character or
the procfs mkdir operation will fail. We don't have such constraints for
GPIO consumer labels which are used verbatim as interrupt labels for
GPIO irqs. We must therefore sanitize the consumer string before
requesting the interrupt.
Let's replace all "/" with ":".
Cc: stable@vger.kernel.org
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Closes: https://lore.kernel.org/linux-gpio/39fe95cb-aa83-4b8b-8cab-63947a726754@gmx.net/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d776cfd5e ]
This devm API takes a consumer device as an argument to setup the devm
action, but throws it away when calling further into gpiolib. This leads
to odd debug messages like this:
(NULL device *): using DT '/gpio-keys/switch-pen-insert' for '(null)' GPIO lookup
Let's pass the consumer device down, by directly calling what
fwnode_gpiod_get_index() calls but pass the device used for devm. This
changes the message to look like this instead:
gpio-keys gpio-keys: using DT '/gpio-keys/switch-pen-insert' for '(null)' GPIO lookup
Note that callers of fwnode_gpiod_get_index() will still see the NULL
device pointer debug message, but there's not much we can do about that
because the API doesn't take a struct device.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 8eb1f71e7a ("gpiolib: consolidate GPIO lookups")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f575957882 ]
The vf610 gpio driver is enabled by default for all i.MX machines,
without any option to disable it in a board-specific config file.
Most i.MX chipsets have no hardware for this driver. Change the default
to enable GPIO_VF610 for SOC_VF610 and disable it otherwise.
Add a text description after the bool type, this makes the driver
selectable by make config etc.
Fixes: 30a35c07d9 ("gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5c54a9d3 ]
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61 ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530b1dbd97 ]
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0f (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84aef4ed59 ]
The raw interrupt status of eic maybe set before the interrupt is enabled,
since the eic interrupt has a latch function, which would trigger the
interrupt event once enabled it from user side. To solve this problem,
interrupts generated before setting the interrupt trigger type are ignored.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 805c74eac8 upstream.
Spurious wakeups are reported on the GPD G1619-04 which
can be absolved by programming the GPIO to ignore wakeups.
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Melikov <mail@gmelikov.ru>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3073
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e404b0cc9f ]
We have removed all callers of gpiochip_find() so don't mention it in
gpiolib-sysfs.c.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Stable-dep-of: 48e1b4d369 ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfe102f633 ]
gpiochip_find() is wrong and its kernel doc is misleading as the
function doesn't return a reference to the gpio_chip but just a raw
pointer. The chip itself is not guaranteed to stay alive, in fact it can
be deleted at any point. Also: other than GPIO drivers themselves,
nobody else has any business accessing gpio_chip structs.
Provide a new gpio_device_find() function that returns a real reference
to the opaque gpio_device structure that is guaranteed to stay alive for
as long as there are active users of it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Stable-dep-of: 48e1b4d369 ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36aa129f22 ]
In order to start migrating away from accessing struct gpio_chip by
users other than their owners, let's first make the reference management
functions for the opaque struct gpio_device public in the driver.h
header.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: 48e1b4d369 ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1cc3542c76 upstream.
In the hardware implementation of the I2C HID driver based on DesignWare
GPIO IRQ chip, when the user continues to use the I2C HID device in the
suspend process, the I2C HID interrupt will be masked after the resume
process is finished.
This is because the disable_irq()/enable_irq() of the DesignWare GPIO
driver does not synchronize the IRQ mask register state. In normal use
of the I2C HID procedure, the GPIO IRQ irq_mask()/irq_unmask() functions
are called in pairs. In case of an exception, i2c_hid_core_suspend()
calls disable_irq() to disable the GPIO IRQ. With low probability, this
causes irq_unmask() to not be called, which causes the GPIO IRQ to be
masked and not unmasked in enable_irq(), raising an exception.
Add synchronization to the masked register state in the
dwapb_irq_enable()/dwapb_irq_disable() function. mask the GPIO IRQ
before disabling it. After enabling the GPIO IRQ, unmask the IRQ.
Fixes: 7779b34556 ("gpio: add a driver for the Synopsys DesignWare APB GPIO block")
Cc: stable@kernel.org
Co-developed-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
