[ Upstream commit 70654f4c21 ]
The TAS module could not be configured when it's running in pending
status. We need disable the module and configure it again. However, the
pending status is not cleared after the module disabled. TC taprio set
will always return busy even it's disabled.
For example, a user uses tc-taprio to configure Qbv and a future
basetime. The TAS module will run in a pending status. There is no way
to reconfigure Qbv, it always returns busy.
Actually the TAS module can be reconfigured when it's disabled. So it
doesn't need to check the pending status if the TAS module is disabled.
After the patch, user can delete the tc taprio configuration to disable
Qbv and reconfigure it again.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://patch.msgid.link/20240906093550.29985-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6efea51354 upstream.
When performing the port_hwtstamp_set operation, ptp_schedule_worker()
will be called if hardware timestamoing is enabled on any of the ports.
When using multiple ports for PTP, port_hwtstamp_set is executed for
each port. When called for the first time ptp_schedule_worker() returns
0. On subsequent calls it returns 1, indicating the worker is already
scheduled. Currently the ksz driver treats 1 as an error and fails to
complete the port_hwtstamp_set operation, thus leaving the timestamping
configuration for those ports unchanged.
This patch fixes this by ignoring the ptp_schedule_worker() return
value.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/7aae307a-35ca-4209-a850-7b2749d40f90@martin-whitaker.me.uk
Fixes: bb01ad3057 ("net: dsa: microchip: ptp: manipulating absolute time using ptp hw clock")
Signed-off-by: Martin Whitaker <foss@martin-whitaker.me.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240817094141.3332-1-foss@martin-whitaker.me.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 528876d867 ]
If an ATU violation was caused by a CPU Load operation, the SPID could
be larger than DSA_MAX_PORTS (the size of mv88e6xxx_chip.ports[] array).
Fixes: 75c05a74e7 ("net: dsa: mv88e6xxx: Fix counting of ATU violations")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240819235251.1331763-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e12ac3be ]
As explained by Horatiu Vultur in commit 603ead9658 ("net: sparx5: Add
spinlock for frame transmission from CPU") which is for a similar
hardware design, multiple CPUs can simultaneously perform injection
or extraction. There are only 2 register groups for injection and 2
for extraction, and the driver only uses one of each. So we'd better
serialize access using spin locks, otherwise frame corruption is
possible.
Note that unlike in sparx5, FDMA in ocelot does not have this issue
because struct ocelot_fdma_tx_ring already contains an xmit_lock.
I guess this is mostly a problem for NXP LS1028A, as that is dual core.
I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka
the felix DSA driver) started using register-based packet injection and
extraction.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa63c6434b ]
The VSC73xx has a busy flag used during MDIO operations. It is raised
when MDIO read/write operations are in progress. Without it, PHYs are
misconfigured and bus operations do not work as expected.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb7e33d01d ]
Switch the delay loop during the Arbiter empty check from
vsc73xx_adjust_link() to use read_poll_timeout(). Functionally,
one msleep() call is eliminated at the end of the loop in the timeout
case.
As Russell King suggested:
"This [change] avoids the issue that on the last iteration, the code reads
the register, tests it, finds the condition that's being waiting for is
false, _then_ waits and end up printing the error message - that last
wait is rather useless, and as the arbiter state isn't checked after
waiting, it could be that we had success during the last wait."
Suggested-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-2-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: fa63c6434b ("net: dsa: vsc73xx: check busy flag in MDIO operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b9eebc2c7 ]
In the 'vsc73xx_phy_write' function, the register value is missing,
and the phy write operation always sends zeros.
This commit passes the value variable into the proper register.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3862093ee ]
bcm_sf2_mdio_register() calls of_phy_find_device() and then
phy_device_remove() in a loop to remove existing PHY devices.
of_phy_find_device() eventually calls bus_find_device(), which calls
get_device() on the returned struct device * to increment the refcount.
The current implementation does not decrement the refcount, which causes
memory leak.
This commit adds the missing phy_device_free() call to decrement the
refcount via put_device() to balance the refcount.
Fixes: 771089c2a4 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806011327.3817861-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5118072e2 ]
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame
configuration. In the commit referenced with the Fixes tag, the setting
is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient chip-wide maximum frame size for the CPU port.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports. This aligns the driver
to the behavior of other switch drivers.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66b6095c26 ]
Marvell chips not supporting per-port jumbo frame size configurations use
a chip-wide frame size configuration. In the commit referenced with the
Fixes tag, the setting is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient maximum frame size for the CPU port. Specifically, sending
full-size frames from the CPU port on a MV88E6097 having a user port MTU
of 1500 bytes results in dropped frames.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
felix_validate_phy_mode() essentially does a pre-validation of the
phy-mode prior to instantiating phylink. But we can let phylink do it,
and this gives us the advantage of being able to dynamically change the
ocelot_port->phy_mode at runtime.
There is code in ocelot_port_update_active_preemptible_tcs() which still
looks at ocelot_port->phy_mode. Since the MAC Merge feature inherently
depends on having a link, then it is no problem to leave the initial
ocelot_port->phy_mode == PHY_INTERFACE_MODE_NA and then update it from
the phylink_mac_ops :: mac_config() method. It will always be up-to-date
enough.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Rid one use of ocelot_port->phy_mode. My issue with that is its use
prior to phylink creation. We want phylink to determine it, because that
way we support runtime reconfiguration of SerDes protocols.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[ Upstream commit 0005b2dc43 ]
The 'phy' parameter supplied to lan9303_phy_read/_write was sometimes a
DSA port number and sometimes a PHY address. This isn't a problem as
long as they are equal. But if the external phy_addr_sel_strap pin is
wired to 'high', the PHY addresses change from 0-1-2 to 1-2-3 (CPU,
slave0, slave1). In this case, lan9303_phy_read/_write must translate
between DSA port numbers and the corresponding PHY address.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240703145718.19951-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c7f3950a9 ]
Since commit a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO
busses") mv88e6xxx_default_mdio_bus() has checked that the
return value of list_first_entry() is non-NULL.
This appears to be intended to guard against the list chip->mdios being
empty. However, it is not the correct check as the implementation of
list_first_entry is not designed to return NULL for empty lists.
Instead, use list_first_entry_or_null() which does return NULL if the
list is empty.
Flagged by Smatch.
Compile tested only.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430-mv88e6xx-list_empty-v3-1-c35c69d88d2e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1c4b4d452 ]
The switch global port interrupt mask, REG_SW_PORT_INT_MASK__4, is
defined as 0x001C in ksz9477_reg.h. The designers used 32-bit value in
anticipation for increase of port count in future product but currently
the maximum port count is 7 and the effective value is 0x7F in register
0x001F. Each port has its own interrupt mask and is defined as 0x#01F.
It uses only 4 bits for different interrupts.
The developer who implemented the current interrupt mechanism in the
switch driver noticed there are similarities between the mechanism to
mask port interrupts in global interrupt and individual interrupts in
each port and so used the same code to handle these interrupts. He
updated the code to use the new macro REG_SW_PORT_INT_MASK__1 which is
defined as 0x1F in ksz_common.h but he forgot to update the 32-bit write
to 8-bit as now the mask registers are 0x1F and 0x#01F.
In addition all KSZ switches other than the KSZ9897/KSZ9893 and LAN937X
families use only 8-bit access and so this common code will eventually
be changed to accommodate them.
Fixes: e1add7dd61 ("net: dsa: microchip: use common irq routines for girq and pirq")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://lore.kernel.org/r/1719009262-2948-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d963c95bc9 ]
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad53f5f54f ]
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=1haK
-----END PGP SIGNATURE-----
Merge tag 'v6.6.36' into lf-6.6.y
This is the 6.6.36 stable release
* tag 'v6.6.36': (192 commits)
Linux 6.6.36
Revert "mm: mmap: allow for the maximum number of bits for randomizing mmap_base by default"
hid: asus: asus_report_fixup: fix potential read out of bounds
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
Documentation/devicetree/bindings/dma/fsl,edma.yaml
arch/arm64/boot/dts/freescale/imx8qm-mek.dts
drivers/spi/spi-imx.c
-----BEGIN PGP SIGNATURE-----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=H63O
-----END PGP SIGNATURE-----
Merge tag 'v6.6.35' into lf-6.6.y
This is the 6.6.35 stable release
* tag 'v6.6.35': (268 commits)
Linux 6.6.35
zap_pid_ns_processes: clear TIF_NOTIFY_SIGNAL along with TIF_SIGPENDING
i2c: designware: Fix the functionality flags of the slave-only interface
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
[ Upstream commit 5edc6585aa ]
This switch family supports four LEDs for each of its six ports. Each
LED group is composed of one of these four LEDs from all six ports. LED
groups can be configured to display hardware information, such as link
activity, or manually controlled through a bitmap in registers
RTL8366RB_LED_0_1_CTRL_REG and RTL8366RB_LED_2_3_CTRL_REG.
After a reset, the default LED group configuration for groups 0 to 3
indicates, respectively, link activity, link at 1000M, 100M, and 10M, or
RTL8366RB_LED_CTRL_REG as 0x5432. These configurations are commonly used
for LED indications. However, the driver was replacing that
configuration to use manually controlled LEDs (RTL8366RB_LED_FORCE)
without providing a way for the OS to control them. The default
configuration is deemed more useful than fixed, uncontrollable turned-on
LEDs.
The driver was enabling/disabling LEDs during port_enable/disable.
However, these events occur when the port is administratively controlled
(up or down) and are not related to link presence. Additionally, when a
port N was disabled, the driver was turning off all LEDs for group N,
not only the corresponding LED for port N in any of those 4 groups. In
such cases, if port 0 was brought down, the LEDs for all ports in LED
group 0 would be turned off. As another side effect, the driver was
wrongly warning that port 5 didn't have an LED ("no LED for port 5").
Since showing the administrative state of ports is not an orthodox way
to use LEDs, it was not worth it to fix it and all this code was
dropped.
The code to disable LEDs was simplified only changing each LED group to
the RTL8366RB_LED_OFF state. Registers RTL8366RB_LED_0_1_CTRL_REG and
RTL8366RB_LED_2_3_CTRL_REG are only used when the corresponding LED
group is configured with RTL8366RB_LED_FORCE and they don't need to be
cleaned. The code still references an LED controlled by
RTL8366RB_INTERRUPT_CONTROL_REG, but as of now, no test device has
actually used it. Also, some magic numbers were replaced by macros.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d029edefed ]
The documentation for device_get_named_child_node() mentions this
important point:
"
The caller is responsible for calling fwnode_handle_put() on the
returned fwnode pointer.
"
Add fwnode_handle_put() to avoid leaked references.
Fixes: 1e264f9d29 ("net: dsa: qca8k: add LEDs basic support")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEZH8oZUiU471FcZm+ONu9yGCSaT4FAmZu0U0ACgkQONu9yGCS
aT4c2Q//SGn9+yEUml1/7nQUTND434ly4JPMdrR1jjJSKwxAsgzOYKCoUpzpXim8
7mdKz7q1cXx/l+tfJgEDdJ8JzVS6ipJWAwF4vE+18zWZjEax/M3dgluZUUswXKYg
Da76wSaNkfGiIewu8HV90LKAKaQoCR4ypyWG8CqDZkCnGJORUJA09GNDrKFhOodT
f0TzjIvPw8E3rU2+HZfPmxUI0XQEzfVPWb5DK+0F7hcHw4ETcij7y0AInBkQ5bNt
tFRCc462nT23e3jXJECWMbSXdRF57LlT8G9626Om0iS+TY7YD6PPNa7/bdqVHzcw
hDmKE+xONslwvuzkYn2R9u+nc/dw/hJ8QI5j9QohbJCcXjcv8N3QeXoiLPjiDxxv
1JVVi6emyKvKx26kjY/m0ZTZ/QWWwQlj/+R8Or/yIMMYZvPwyBUX3I8cZIQhyAg4
n/fc2tFqmax0K6e9YOXj3sa+OlXx02DAC8oVToNrSS7HT5uhtoKT4vU1d+et2alo
dFJAhklt27k+eV+Ayxo+RUaxUVggM0MAB67S7XUR0kylP2BeL2l9wMKVzZz2V5T4
O9PHY1RpD8OGk7aZvlbZYIis7LBqVTXcaEB4l5QtSYM4RMON4BYb5QLEc0jYywzV
U7GMNiKhhuwEHjiPD0cIXyeWeQzTlH9os5lhW8moVY9mtthGlr0=
=zdH0
-----END PGP SIGNATURE-----
Merge tag 'v6.6.34' into lf-6.6.y
This is the 6.6.34 stable release
* tag 'v6.6.34': (2530 commits)
Linux 6.6.34
smp: Provide 'setup_max_cpus' definition on UP too
selftests: net: more strict check in net_helper
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
drivers/net/ethernet/freescale/fec_ptp.c
drivers/pmdomain/imx/imx8mp-blk-ctrl.c
drivers/usb/dwc3/host.c
tools/perf/util/pmu.c
[ Upstream commit 278d65ccda ]
The driver should return RMII interface when XMII is running in RMII mode.
Fixes: 0ab7f6bf16 ("net: dsa: microchip: ksz9477: use common xmii function")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Acked-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1716932066-3342-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e44894e2aa ]
88E6250-family switches have the quirk that the EEPROM Running flag can
get stuck at 1 when no EEPROM is connected, causing
mv88e6xxx_g2_eeprom_wait() to time out. We still want to wait for the
EEPROM however, to avoid interrupting a transfer and leaving the EEPROM
in an invalid state.
The condition to wait for recommended by the hardware spec is the EEInt
flag, however this flag is cleared on read, so before the hardware reset,
is may have been cleared already even though the EEPROM has been read
successfully.
For this reason, we revive the mv88e6xxx_g1_wait_eeprom_done() function
that was removed in commit 6ccf50d4d4
("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent") in a
slightly refactored form, and introduce a new
mv88e6xxx_g1_wait_eeprom_done_prereset() that additionally handles this
case by triggering another EEPROM reload that can be waited on.
On other switch models without this quirk, mv88e6xxx_g2_eeprom_wait() is
kept, as it avoids the additional reload.
Fixes: 6ccf50d4d4 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fdd27b9d6 ]
Instead of calling mv88e6xxx_g2_eeprom_wait() directly from
mv88e6xxx_hardware_reset(), add configurable pre- and post-reset hard
reset handlers. Initially, the handlers are set to
mv88e6xxx_g2_eeprom_wait() for all families that have get/set_eeprom()
to match the existing behavior. No functional change intended (except
for additional error messages on failure).
Fixes: 6ccf50d4d4 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f39bf3cf08 ]
As of commit de5c9bf40c ("net: phylink: require supported_interfaces to
be filled")
Marvell 88e6320/21 switches fail to be probed:
...
mv88e6085 30be0000.ethernet-1:00: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities.
Since there are serdes only ports 0/1 included, create a new dedicated
phylink_get_caps for the 6320 and 6321 to properly support their
set of capabilities.
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240508072944.54880-2-steffen@innosonix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9a61c2017 ]
The Topaz family (88E6141 and 88E6341) only support 256 Forwarding
Information Tables.
Fixes: a75961d0eb ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6341")
Fixes: 1558727a1c ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240429133832.9547-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4e3899065 ]
With the recent PHYLINK changes requiring supported_interfaces to be set,
MV88E6250 family switches like the 88E6020 fail to probe - cmode is
never initialized on these devices, so mv88e6250_phylink_get_caps() does
not set any supported_interfaces flags.
Instead of a cmode, on 88E6250 we have a read-only port mode value that
encodes similar information. There is no reason to bother mapping port
mode to the cmodes of other switch models; instead we introduce a
mv88e6250_setup_supported_interfaces() that is called directly from
mv88e6250_phylink_get_caps().
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240417103737.166651-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 06dfcd4098 upstream.
The commit 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is
enabled on MT7531 switch MACs by pulling the LAN2LED0 pin low on the board
(bootstrapping), unsetting the EEE_DIS bit on the trap register, or setting
the internal EEE switch bit on the CORE_PLL_GROUP4 register. Thanks to
SkyLake Huang (黃啟澤) from MediaTek for providing information on the
internal EEE switch bit.
There are existing boards that were not designed to pull the pin low.
Because of that, the EEE status currently depends on the board design.
The EEE_DIS bit on the trap pertains to the LAN2LED0 pin which is usually
used to control an LED. Once the bit is unset, the pin will be low. That
will make the active low LED turn on. The pin is controlled by the switch
PHY. It seems that the PHY controls the pin in the way that it inverts the
pin state. That means depending on the wiring of the LED connected to
LAN2LED0 on the board, the LED may be on without an active link.
To not cause this unwanted behaviour whilst enabling EEE on all boards, set
the internal EEE switch bit on the CORE_PLL_GROUP4 register.
My testing on MT7531 shows a certain amount of traffic loss when EEE is
enabled. That said, I haven't come across a board that enables EEE. So
enable EEE on the switch MACs but disable EEE advertisement on the switch
PHYs. This way, we don't change the behaviour of the majority of the boards
that have this switch. The mediatek-ge PHY driver already disables EEE
advertisement on the switch PHYs but my testing shows that it is somehow
enabled afterwards. Disabling EEE advertisement before the PHY driver
initialises keeps it off.
With this change, EEE can now be enabled using ethtool.
Fixes: 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240408-for-net-mt7530-fix-eee-for-mt7531-mt7988-v3-1-84fdef1f008b@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f563c31ff upstream.
The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.
The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.
Introduce a check to run it only on MT7530 with 40MHz XTAL.
The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.
When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.
When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.
For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.
Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.
With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.
Link: 4a5dd143f2/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c (L1039)
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c606d1385 ]
The "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open Version)
v0.1" document shows bits 16 to 18 as the MIRROR_PORT field of the CPU
forward control register. Currently, the MT7530 DSA subdriver configures
bits 0 to 2 of the CPU forward control register which breaks the port
mirroring feature for the MT7988 SoC switch.
Fix this by using the MT7531_MIRROR_PORT_GET() and MT7531_MIRROR_PORT_SET()
macros which utilise the correct bits.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d59cf049c8 ]
This switch intellectual property provides a bit on the ARL global control
register which controls allowing mirroring frames which are received on the
local port (monitor port). This bit is unset after reset.
This ability must be enabled to fully support the port mirroring feature on
this switch intellectual property.
Therefore, this patch fixes the traffic not being reflected on a port,
which would be configured like below:
tc qdisc add dev swp0 clsact
tc filter add dev swp0 ingress matchall skip_sw \
action mirred egress mirror dev swp0
As a side note, this configuration provides the hairpinning feature for a
single port.
Fixes: 37feab6076 ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17c5601132 ]
In Clause 5 of IEEE Std 802-2014, two sublayers of the data link layer
(DLL) of the Open Systems Interconnection basic reference model (OSI/RM)
are described; the medium access control (MAC) and logical link control
(LLC) sublayers. The MAC sublayer is the one facing the physical layer.
In 8.2 of IEEE Std 802.1Q-2022, the Bridge architecture is described. A
Bridge component comprises a MAC Relay Entity for interconnecting the Ports
of the Bridge, at least two Ports, and higher layer entities with at least
a Spanning Tree Protocol Entity included.
Each Bridge Port also functions as an end station and shall provide the MAC
Service to an LLC Entity. Each instance of the MAC Service is provided to a
distinct LLC Entity that supports protocol identification, multiplexing,
and demultiplexing, for protocol data unit (PDU) transmission and reception
by one or more higher layer entities.
It is described in 8.13.9 of IEEE Std 802.1Q-2022 that in a Bridge, the LLC
Entity associated with each Bridge Port is modeled as being directly
connected to the attached Local Area Network (LAN).
On the switch with CPU port architecture, CPU port functions as Management
Port, and the Management Port functionality is provided by software which
functions as an end station. Software is connected to an IEEE 802 LAN that
is wholly contained within the system that incorporates the Bridge.
Software provides access to the LLC Entity associated with each Bridge Port
by the value of the source port field on the special tag on the frame
received by software.
We call frames that carry control information to determine the active
topology and current extent of each Virtual Local Area Network (VLAN),
i.e., spanning tree or Shortest Path Bridging (SPB) and Multiple VLAN
Registration Protocol Data Units (MVRPDUs), and frames from other link
constrained protocols, such as Extensible Authentication Protocol over LAN
(EAPOL) and Link Layer Discovery Protocol (LLDP), link-local frames. They
are not forwarded by a Bridge. Permanently configured entries in the
filtering database (FDB) ensure that such frames are discarded by the
Forwarding Process. In 8.6.3 of IEEE Std 802.1Q-2022, this is described in
detail:
Each of the reserved MAC addresses specified in Table 8-1
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]) shall be
permanently configured in the FDB in C-VLAN components and ERs.
Each of the reserved MAC addresses specified in Table 8-2
(01-80-C2-00-00-[01,02,03,04,05,06,07,08,09,0A,0E]) shall be permanently
configured in the FDB in S-VLAN components.
Each of the reserved MAC addresses specified in Table 8-3
(01-80-C2-00-00-[01,02,04,0E]) shall be permanently configured in the FDB
in TPMR components.
The FDB entries for reserved MAC addresses shall specify filtering for all
Bridge Ports and all VIDs. Management shall not provide the capability to
modify or remove entries for reserved MAC addresses.
The addresses in Table 8-1, Table 8-2, and Table 8-3 determine the scope of
propagation of PDUs within a Bridged Network, as follows:
The Nearest Bridge group address (01-80-C2-00-00-0E) is an address that
no conformant Two-Port MAC Relay (TPMR) component, Service VLAN (S-VLAN)
component, Customer VLAN (C-VLAN) component, or MAC Bridge can forward.
PDUs transmitted using this destination address, or any other addresses
that appear in Table 8-1, Table 8-2, and Table 8-3
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]), can
therefore travel no further than those stations that can be reached via a
single individual LAN from the originating station.
The Nearest non-TPMR Bridge group address (01-80-C2-00-00-03), is an
address that no conformant S-VLAN component, C-VLAN component, or MAC
Bridge can forward; however, this address is relayed by a TPMR component.
PDUs using this destination address, or any of the other addresses that
appear in both Table 8-1 and Table 8-2 but not in Table 8-3
(01-80-C2-00-00-[00,03,05,06,07,08,09,0A,0B,0C,0D,0F]), will be relayed
by any TPMRs but will propagate no further than the nearest S-VLAN
component, C-VLAN component, or MAC Bridge.
The Nearest Customer Bridge group address (01-80-C2-00-00-00) is an
address that no conformant C-VLAN component, MAC Bridge can forward;
however, it is relayed by TPMR components and S-VLAN components. PDUs
using this destination address, or any of the other addresses that appear
in Table 8-1 but not in either Table 8-2 or Table 8-3
(01-80-C2-00-00-[00,0B,0C,0D,0F]), will be relayed by TPMR components and
S-VLAN components but will propagate no further than the nearest C-VLAN
component or MAC Bridge.
Because the LLC Entity associated with each Bridge Port is provided via CPU
port, we must not filter these frames but forward them to CPU port.
In a Bridge, the transmission Port is majorly decided by ingress and egress
rules, FDB, and spanning tree Port State functions of the Forwarding
Process. For link-local frames, only CPU port should be designated as
destination port in the FDB, and the other functions of the Forwarding
Process must not interfere with the decision of the transmission Port. We
call this process trapping frames to CPU port.
Therefore, on the switch with CPU port architecture, link-local frames must
be trapped to CPU port, and certain link-local frames received by a Port of
a Bridge comprising a TPMR component or an S-VLAN component must be
excluded from it.
A Bridge of the switch with CPU port architecture cannot comprise a
Two-Port MAC Relay (TPMR) component as a TPMR component supports only a
subset of the functionality of a MAC Bridge. A Bridge comprising two Ports
(Management Port doesn't count) of this architecture will either function
as a standard MAC Bridge or a standard VLAN Bridge.
Therefore, a Bridge of this architecture can only comprise S-VLAN
components, C-VLAN components, or MAC Bridge components. Since there's no
TPMR component, we don't need to relay PDUs using the destination addresses
specified on the Nearest non-TPMR section, and the proportion of the
Nearest Customer Bridge section where they must be relayed by TPMR
components.
One option to trap link-local frames to CPU port is to add static FDB
entries with CPU port designated as destination port. However, because that
Independent VLAN Learning (IVL) is being used on every VID, each entry only
applies to a single VLAN Identifier (VID). For a Bridge comprising a MAC
Bridge component or a C-VLAN component, there would have to be 16 times
4096 entries. This switch intellectual property can only hold a maximum of
2048 entries. Using this option, there also isn't a mechanism to prevent
link-local frames from being discarded when the spanning tree Port State of
the reception Port is discarding.
The remaining option is to utilise the BPC, RGAC1, RGAC2, RGAC3, and RGAC4
registers. Whilst this applies to every VID, it doesn't contain all of the
reserved MAC addresses without affecting the remaining Standard Group MAC
Addresses. The REV_UN frame tag utilised using the RGAC4 register covers
the remaining 01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F] destination
addresses. It also includes the 01-80-C2-00-00-22 to 01-80-C2-00-00-FF
destination addresses which may be relayed by MAC Bridges or VLAN Bridges.
The latter option provides better but not complete conformance.
This switch intellectual property also does not provide a mechanism to trap
link-local frames with specific destination addresses to CPU port by
Bridge, to conform to the filtering rules for the distinct Bridge
components.
Therefore, regardless of the type of the Bridge component, link-local
frames with these destination addresses will be trapped to CPU port:
01-80-C2-00-00-[00,01,02,03,0E]
In a Bridge comprising a MAC Bridge component or a C-VLAN component:
Link-local frames with these destination addresses won't be trapped to
CPU port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F]
In a Bridge comprising an S-VLAN component:
Link-local frames with these destination addresses will be trapped to CPU
port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-00
Link-local frames with these destination addresses won't be trapped to
CPU port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-[04,05,06,07,08,09,0A]
Currently on this switch intellectual property, if the spanning tree Port
State of the reception Port is discarding, link-local frames will be
discarded.
To trap link-local frames regardless of the spanning tree Port State, make
the switch regard them as Bridge Protocol Data Units (BPDUs). This switch
intellectual property only lets the frames regarded as BPDUs bypass the
spanning tree Port State function of the Forwarding Process.
With this change, the only remaining interference is the ingress rules.
When the reception Port has no PVID assigned on software, VLAN-untagged
frames won't be allowed in. There doesn't seem to be a mechanism on the
switch intellectual property to have link-local frames bypass this function
of the Forwarding Process.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240409-b4-for-net-mt7530-fix-link-local-when-stp-discarding-v2-1-07b1150164ac@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 625aefac34 upstream.
The switch has 4 ports with 2 internal PHYs, but ports are numbered up
to 6, with ports 0, 1, 5 and 6 being usable.
Fixes: 71d94a432a ("net: dsa: mv88e6xxx: add support for MV88E6020 switch")
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326123655.40666-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c120209bce upstream.
The definition and declaration of sja1110_pcs_mdio_write_c45() don't have
parameters in the same order.
Knowing that sja1110_pcs_mdio_write_c45() is used as a function pointer
in 'sja1105_info' structure with .pcs_mdio_write_c45, and that we have:
int (*pcs_mdio_write_c45)(struct mii_bus *bus, int phy, int mmd,
int reg, u16 val);
it is likely that the definition is the one to change.
Found with cppcheck, funcArgOrderDifferent.
Fixes: ae271547bb ("net: dsa: sja1105: C45 only transactions for PCS")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/ff2a5af67361988b3581831f7bd1eddebfb4c48f.1712082763.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69ddba9d17 ]
Currently, the MT753X switches treat frames with :01-0D and :0F MAC DAs as
regular multicast frames, therefore flooding them to user ports.
On page 205, section "8.6.3 Frame filtering" of the active standard, IEEE
Std 802.1Q™-2022, it is stated that frames with 01:80:C2:00:00:00-0F as MAC
DA must only be propagated to C-VLAN and MAC Bridge components. That means
VLAN-aware and VLAN-unaware bridges. On the switch designs with CPU ports,
these frames are supposed to be processed by the CPU (software). So we make
the switch only forward them to the CPU port. And if received from a CPU
port, forward to a single port. The software is responsible of making the
switch conform to the latter by setting a single port as destination port
on the special tag.
This switch intellectual property cannot conform to this part of the
standard fully. Whilst the REV_UN frame tag covers the remaining :04-0D and
:0F MAC DAs, it also includes :22-FF which the scope of propagation is not
supposed to be restricted for these MAC DAs.
Set frames with :01-03 MAC DAs to be trapped to the CPU port(s). Add a
comment for the remaining MAC DAs.
Note that the ingress port must have a PVID assigned to it for the switch
to forward untagged frames. A PVID is set by default on VLAN-aware and
VLAN-unaware ports. However, when the network interface that pertains to
the ingress port is attached to a vlan_filtering enabled bridge, the user
can remove the PVID assignment from it which would prevent the link-local
frames from being trapped to the CPU port. I am yet to see a way to forward
link-local frames while preventing other untagged frames from being
forwarded too.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8bf353577 ]
Whether VLAN-aware or not, on every VID VLAN table entry that has the CPU
port as a member of it, frames are set to egress the CPU port with the VLAN
tag stacked. This is so that VLAN tags can be appended after hardware
special tag (called DSA tag in the context of Linux drivers).
For user ports on a VLAN-unaware bridge, frame ingressing the user port
egresses CPU port with only the special tag.
For user ports on a VLAN-aware bridge, frame ingressing the user port
egresses CPU port with the special tag and the VLAN tag.
This causes issues with link-local frames, specifically BPDUs, because the
software expects to receive them VLAN-untagged.
There are two options to make link-local frames egress untagged. Setting
CONSISTENT or UNTAGGED on the EG_TAG bits on the relevant register.
CONSISTENT means frames egress exactly as they ingress. That means
egressing with the VLAN tag they had at ingress or egressing untagged if
they ingressed untagged. Although link-local frames are not supposed to be
transmitted VLAN-tagged, if they are done so, when egressing through a CPU
port, the special tag field will be broken.
BPDU egresses CPU port with VLAN tag egressing stacked, received on
software:
00:01:25.104821 AF Unknown (382365846), length 106:
| STAG | | VLAN |
0x0000: 0000 6c27 614d 4143 0001 0000 8100 0001 ..l'aMAC........
0x0010: 0026 4242 0300 0000 0000 0000 6c27 614d .&BB........l'aM
0x0020: 4143 0000 0000 0000 6c27 614d 4143 0000 AC......l'aMAC..
0x0030: 0000 1400 0200 0f00 0000 0000 0000 0000 ................
BPDU egresses CPU port with VLAN tag egressing untagged, received on
software:
00:23:56.628708 AF Unknown (25215488), length 64:
| STAG |
0x0000: 0000 6c27 614d 4143 0001 0000 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
BPDU egresses CPU port with VLAN tag egressing tagged, received on
software:
00:01:34.311963 AF Unknown (25215488), length 64:
| Mess |
0x0000: 0000 6c27 614d 4143 0001 0001 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
To prevent confusing the software, force the frame to egress UNTAGGED
instead of CONSISTENT. This way, frames can't possibly be received TAGGED
by software which would have the special tag field broken.
VLAN Tag Egress Procedure
For all frames, one of these options set the earliest in this order will
apply to the frame:
- EG_TAG in certain registers for certain frames.
This will apply to frame with matching MAC DA or EtherType.
- EG_TAG in the address table.
This will apply to frame at its incoming port.
- EG_TAG in the PVC register.
This will apply to frame at its incoming port.
- EG_CON and [EG_TAG per port] in the VLAN table.
This will apply to frame at its outgoing port.
- EG_TAG in the PCR register.
This will apply to frame at its outgoing port.
EG_TAG in certain registers for certain frames:
PPPoE Discovery_ARP/RARP: PPP_EG_TAG and ARP_EG_TAG in the APC register.
IGMP_MLD: IGMP_EG_TAG and MLD_EG_TAG in the IMC register.
BPDU and PAE: BPDU_EG_TAG and PAE_EG_TAG in the BPC register.
REV_01 and REV_02: R01_EG_TAG and R02_EG_TAG in the RGAC1 register.
REV_03 and REV_0E: R03_EG_TAG and R0E_EG_TAG in the RGAC2 register.
REV_10 and REV_20: R10_EG_TAG and R20_EG_TAG in the RGAC3 register.
REV_21 and REV_UN: R21_EG_TAG and RUN_EG_TAG in the RGAC4 register.
With this change, it can be observed that a bridge interface with stp_state
and vlan_filtering enabled will properly block ports now.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f490c492e9 ]
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 0 Reserved
0 1 20MHz
1 0 40MHz
1 1 25MHz
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] [3] [5]
: : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
_____________________________
ESW_P3_LED_0 |__________________________
: : : :
: : [4]...:
: :
[2]................:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] [2-1] [3] [5]
: : : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
___________________ _______
ESW_P3_LED_0 |_________| |__________________
: : : : :
: [2-2]...: [4]...:
[2]................:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
ESW_P3_LED_0 low period before reset deassertion:
5000 usec
- 5100 usec
TEST RESET HOLD
# (usec)
---------------------
1 5410
2 5440
3 4375
4 5490
5 5475
6 4335
7 4370
8 5435
9 4205
10 4335
11 3750
12 3170
13 4395
14 4375
15 3515
16 4335
17 4220
18 4175
19 4175
20 4350
Min 3170
Max 5490
Median 4342.500
Avg 4466.500
Revert commit 2920dd92b9 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7fb7729c9 ]
This bug was noticed while re-implementing parts of the kernel
driver in userspace using spidev. The goal was to enable some
of the errata workarounds that Microchip describes in their
errata sheet [1].
Both the errata sheet and the regular datasheet of e.g. the KSZ8795
imply that you need to do this for indirect register accesses:
- write a 16-bit value to a control register pair (this value
consists of the indirect register table, and the offset inside
the table)
- either read or write an 8-bit value from the data storage
register (indicated by REG_IND_BYTE in the kernel)
The current implementation has the order swapped. It can be
proven, by reading back some indirect register with known content
(the EEE register modified in ksz8_handle_global_errata() is one of
these), that this implementation does not work.
Private discussion with Oleksij Rempel of Pengutronix has revealed
that the workaround was apparantly never tested on actual hardware.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/Errata/KSZ87xx-Errata-DS80000687C.pdf
Signed-off-by: Tobias Jakobi (Compleo) <tobias.jakobi.compleo@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 7b6e6235b6 ("net: dsa: microchip: ksz8795: handle eee specif erratum")
Link: https://lore.kernel.org/r/20240304154135.161332-1-tobias.jakobi.compleo@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 585b40e25d upstream.
Not all mv88e6xxx device support C45 read/write operations. Those
which do not return -EOPNOTSUPP. However, when phylib scans the bus,
it considers this fatal, and the probe of the MDIO bus fails, which in
term causes the mv88e6xxx probe as a whole to fail.
When there is no device on the bus for a given address, the pull up
resistor on the data line results in the read returning 0xffff. The
phylib core code understands this when scanning for devices on the
bus. C45 allows multiple devices to be supported at one address, so
phylib will perform a few reads at each address, so although thought
not the most efficient solution, it is a way to avoid fatal
errors. Make use of this as a minimal fix for stable to fix the
probing problems.
Follow up patches will rework how C45 operates to make it similar to
C22 which considers -ENODEV as a none-fatal, and swap mv88e6xxx to
using this.
Cc: stable@vger.kernel.org
Fixes: 743a19e38d ("net: dsa: mv88e6xxx: Separate C22 and C45 transactions")
Reported-by: Tim Menninger <tmenninger@purestorage.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129224948.1531452-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c44fc98f0a ]
When working with GPIO, its direction must be set either when the GPIO is
requested by gpiod_get*() or later on by one of the gpiod_direction_*()
functions. Neither of this is done here which results in undefined
behavior on some systems.
As the reset GPIO is used right after it is requested here, it makes sense
to configure it as GPIOD_OUT_HIGH right away. With that, the following
gpiod_set_value_cansleep(1) becomes redundant and can be safely
removed.
Fixes: a653f2f538 ("net: dsa: qca8k: introduce reset via gpio feature")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1706266175-3408-1-git-send-email-michal.vokac@ysoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfa988b4c7 ]
Setup PMCR port register for actual speed and duplex on internally
connected PHYs of the MT7988 built-in switch. This fixes links with
speeds other than 1000M.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/a5b04dfa8256d8302f402545a51ac4c626fdba25.1706071272.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e1010cda ]
of_get_child_by_name() gives us an OF node with an elevated refcount,
which should be dropped when we're done with it. This is so that,
if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can
eventually be freed.
There are 2 distinct paths to be considered in qca8k_mdio_register():
- devm_of_mdiobus_register() succeeds: since commit 3b73a7b8ec ("net:
mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core
treats this well.
- devm_of_mdiobus_register() or anything up to that point fails: it is
the duty of the qca8k driver to release the OF node.
This change addresses the second case by making sure that the OF node
reference is not leaked.
The "mdio" node may be NULL, but of_node_put(NULL) is safe.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc82a08ae7 ]
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
