Refine the system wide run mode flow to add the dynamic
ld mode switching support. usage example:
OD mode:
echo 0 > /sys/devices/platform/imx93-lpm/mode;
ND mode:
echo 1 > /sys/devices/platform/imx93-lpm/mode;
LD mode:
echo 2 > /sys/devices/platform/imx93-lpm/mode;
LD mode with DDR scaling by SWFFC:
echo 3 > /sys/devices/platform/imx93-lpm/mode;
when DDR highest frequency is 3733MTS & system is running at
OD mode, the auto clock gating will be enabled by default to
balance the power & performance. For other case, need to be
enabled by user explictly based on actual case.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Based on i.MX93 CCB#44, the ND mode voltage should be
updated from 0.8V to 0.85V.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Add the DDR and SoC run mode(OD/OD) dynamic power saving support
on i.MX93. This low power control module provides four interface
to control the system wide OD/ND mode swithcing with DDR frequency
scaling by HWFFC, DDR scaling down to a frequency < half of the full
speed, DDR auto clock gating enable & auto clock gating idl strap
to fine tuning the performance & power based on the user case.
the supported controls are exported through the sys interface:
sys/devices/platform/imx93-lpm/mode;
sys/devices/platform/imx93-lpm/swffc;
sys/devices/platform/imx93-lpm/auto_clk_gating;
sys/devices/platform/imx93-lpm/idle_delay;
a). 'mode' is used to switching the od/nd mode with DDR HWFFC;
b). 'swffc' is used for scaling the DDR frequency to a lower one
with system switched to ND mode;
c). 'auto_clk_gating' is used to enable the DDR auto clock gating.
d). 'idle_delay' is used for fine tuning the DDR auto clock gating
strap. a larger value means after the DDRC AXI idle for that
clock count, the DDRC will put the DRAM into self-refresh with
clock gated to save power.
example:
1. switch the system to ND mode:
echo nd > sys/devices/platform/imx93-lpm/mode;
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Adding i.MX93 SoC device register function providers revision,
serial_number and soc_id for other drivers to use.
NOTE: soc-imx9.c depends on imx-ocotp-fsb-s400.c, so add
"depends on NVMEM_IMX_OCOTP_FSB_S400" otherwise we may meet the issue
imx9_init_soc: probe of 47510000.efuse:imx93-soc failed with error -2"
which appears at a low probability because nvmem_add_cells_from_of()
sometimes has not registered nvmem cells when soc-imx9.c calls
nvmem_cell_read_u64().
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Modify config as tristate and add module license to support
building imx8m soc driver as module.
Signed-off-by: Jindong Yue <jindong.yue@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Add rpmsg life cycle support on i.MX8ULP for APD side low power mode
state coordination with M core by sending rpmsg to M4 core. Currently,
only need to send nofity to M core for reboot/poweroff case. APD side
need to send rpmsg to M core side to let it know that APD side will
enter 'DPD' HW mode or do reboot. For both cases, M core side need to
re-init the rpmsg service when APD out of reset.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Fix below section mismatch build warning:
WARNING: modpost: vmlinux.o(.text+0x6b20b8): Section mismatch in reference
from the function imx8_soc_info() to the function .init.text:imx8mq_noc_init()
The function imx8_soc_info() references
the function __init imx8mq_noc_init().
This is often because imx8_soc_info lacks a __init
annotation or the annotation of imx8mq_noc_init is wrong.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The config for lcdif should be removed, and need to add vpu
qos setting by default. this patch is just to add back the
vpu qos config that is missed when resolving cherry-pick
conflict for patch:
3a3f54750294: MLK-19380 driver: soc: update the noc QoS setting on imx8mq
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Allow imx8m busfreq driver to be loaded as a module.
Do not select IMX8M_BUSFREQ by default after enable ARCH_MXC.
Signed-off-by: Jindong Yue <jindong.yue@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
update the noc QoS setting for CPU & VPU on i.MX8MQ.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Jian Li <jian.li@nxp.com>
(cherry picked from commit 45d2dcaecce6d83e5c4a7e9488c651a05b0f05ac)
Config NOC to limit bandwidth to 4GB for both VPU
and CPU to avoid lcdif flickering only when lcdif is enabled.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Bai Ping <ping.bai@nxp.com>
(cherry picked from commit 8ab89ebeb94a423792bf588bdf2354c5960d8f13)
When configuring the kernel to not support iMX, eg:
- make defconfig
- make lsdk.config
- CONFIG_ARCH_MXC=n
The build fails:
aarch64-fsl-linux-ld: drivers/soc/imx/secvio/imx-secvio-sc.o:
in function `int_imx_secvio_sc_disable_irq':
linux-nxp/drivers/soc/imx/secvio/imx-secvio-sc.c:385:
undefined reference to `imx_scu_irq_group_enable'
aarch64-fsl-linux-ld: drivers/soc/imx/secvio/imx-secvio-sc.o:
in function `int_imx_secvio_sc_enable_irq':
linux-nxp/drivers/soc/imx/secvio/imx-secvio-sc.c:343:
undefined reference to `imx_scu_irq_group_enable'
Makefile:1173: recipe for target 'vmlinux' failed
It happens because secvio module requires imx-scu-irq disabled
with CONFIG_ARCH_MXC=n.
This patch modify the Kconfig for the module to add a dependency
on IMX_SCU symbol.
Fixes: 262bd66fafcb (SSI-87: soc: imx: secvio: Add support for SNVS secvio and tamper via SCFW)
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
When the nvmem subsystem is not initialised at boot, the probe
will fail and an error message will be displayed.
In this case the message should not be printed as the driver will
be probed later.
This patch checks the error code from nvmem before printing the
message.
It also fixes the cleaning path as the driver was not exiting
properly.
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
The driver register an IRQ handle to SCU for security
violation interrupt.
When an interruption is fired, the driver inform the user.
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
When DRAM PLL clock is changed in TF-A, the DRAM PLL clock rate needs
to be updated, previous implementation uses dram_pll_clk which is
clock gate and it will NOT trigger clock rate update, need to use PLL
type clock which has CLK_GET_RATE_NOCACHE flag set and will trigger
clock rate recalculation. Otherwise, when system enters low bus mode,
checking clock rate via "cat /sys/kernel/debug/clk/dram_core_clk/clk_rate"
will NOT return the latest dram core clk rate.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
On i.MX6QP, the soc_id exported to the /sys/devices/soc0/soc_id
should be 'i.MX6QP'.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <anson.huang@nxp.com>
[ Aisheng: update changes to drivers/soc/imx/soc-imx.c ]
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
On i.MX8M SOC family, we can support LPDDR4, DDR4 or DDR3L, we may need
to support different setpoint for audio & low bus mode on different DDR type,
So update the code to get all the supported setpoint info from ATF.
The maximum setpoints that can be supported by hardware is 4, if the drate
for a setpoint is '0', that means this setpoint is not enabled. We can use
these info to find out the lowest drate setpoint for audio & low bus mode.
BuildInfo:
- ATF 59fe78cfe7
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
The 100MTS low bus mode can be only supported by i.MX8MQ Rev2.1 and
future TO. So necessary check is added to identify the chip revision
when doing busfreq mode switch.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Use soc_device_metch instead of global imx_get_soc_revision
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
This reverts commit 7560cff21b7b92127675d5e955874af2827a9bca.
drivers/soc/imx/busfreq-imx8mq.o: In function `reduce_bus_freq':
/home/b29396/Work/linux/dash-linux-devel/build_v8/../drivers/soc/imx/busfreq-imx8mq.c:193: undefined reference to `imx_get_soc_revision'
/home/b29396/Work/linux/dash-linux-devel/build_v8/../drivers/soc/imx/busfreq-imx8mq.c:120: undefined reference to `imx_get_soc_revision'
drivers/soc/imx/busfreq-imx8mq.o: In function `set_high_bus_freq':
/home/b29396/Work/linux/dash-linux-devel/build_v8/../drivers/soc/imx/busfreq-imx8mq.c:327: undefined reference to `imx_get_soc_revision'
/home/b29396/Work/linux/dash-linux-devel/Makefile:1052: recipe for target 'vmlinux' failed
make[1]: *** [vmlinux] Error 1
upstream kernel did not export imx_get_soc_revision for mx8.
Need find a better way to support for both mx8m and mx8.
This patch fixes coverity issue of "divide by 0".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Bai Ping <ping.bai@nxp.com>
(cherry picked from commit ed044f6d78)
The 100MTS low bus mode can be only supported by i.MX8MQ Rev2.1 and
future TO. So necessary check is added to identify the chip revision
when doing busfreq mode switch.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
(cherry picked from commit a906afb17d)
add busfreq support on i.MX8MM. when system is running at low bus or
audio bus mode, the dram & bus clock will be reduced to a lower rate:
NOC: 150MHZ, AXI: 24MHz, AXI 20MHZ, DRAM core clock: 25MHz.
when system is running at high bus mode, all the bus clock and dram
clock will be restore to the highest one.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
(cherry picked from commit 4984e653a6)
Currently, on imx8mq evk board, we only support 3200mts and 667mts
frequency setpoints. So the DDR DVFS flow need to be updated accordingly.
The dram pll and dram apb clock rate is changed in ATF when doing frequency,
in kernel side, we need to call the clk API to update the clock rate info
in clock tree.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
(cherry picked from commit a69c3794f5)
A 'return' statement is missed before, So the mutex will be unlocked
twice, in some corner case, one core will unlock the mutex that locked
by anohter core wrongly. Then lead to concurrent access to the DVFS
at the same time.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
(cherry picked from commit 659615af4d)
If the system is currently in low bus mode, if the audio device
request the audio bus mode, the NOC, AHB and AXI bus clock rate
will be set wrongly, then bus will run at very low frequency, then
lead to audio playback underrun.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Tested-by: Anson Huang <anson.huang@nxp.com>
(cherry picked from commit 3a2a988cc0)
reduce the NOC, main AXI and AHB bus clock frequency to save power when DDR enter low
frequency mode. VDDSOC is ~195mA during video play, and ~180mA in idle.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
(cherry picked from commit e109b34d30)
If audio device is the only that access to ddr memory, the DDR
frequency can be reduce to 25MHz to save power. when DDR run in
25MHz frequency, the memory bandwidth is about 66MB/s, it can
meet the performance requirement for audio only case.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Anson Huang <anson.huang@nxp.com>
(cherry picked from commit 7c2389b6dc)
Add busfreq driver support on i.MX8MQ. The busfreq driver is
mainly used for dynamic DDR frequency change for power saving
feature. When there is no peripheral or DMA device has direct
access to DDR memory, we can lower the DDR frequency to save
power. Currently, we support frequency setpoint for LPDDR4:
(1): 3200mts, the DDRC core clock is sourced from 800MHz
dram_pll, the DDRC apb clock is 200MHz.
(2): 400mts, the DDRC core clock is source from sys1_pll_400m,
the DDRC apb clock is is sourced from sys1_pll_40m.
(3): 100mts, the DDRC core clock is sourced from sys1_pll_100m,
the DDRC apb clock is sourced from sys1_pll_40m.
In our busfreq driver, we have three mode supported:
* high bus mode <-----> 3200mts;
* audio bus mode <-----> 400mts;
* low bus mode <-----> 100mts;
The actual DDR frequency is done in ARM trusted firmware by calling
the SMCC SiP service call.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Use CONFIG_IMX8M_BUSFREQ
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[ Leo: Updated the confusing Kconfig description of HAVE_IMX_BUSFREQ ]
Signed-off-by: Li Yang <leoyang.li@nxp.com>
- Sort out a few Kconfig dependency issues for the rich set of RISC-V
non-coherent DMA support.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZTowWwAKCRCKwlD9ZEnx
cH8wAP49M82pS/aT2KpT+ANVdb7GqUemkYQKn9dI1y4yI5G+IwEAoDBzjUZ//aS0
FgLgVyJrUUy3MVIGiqi/WX+N1GehjQg=
=LXd4
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=+T5y
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v6.6-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v6.6 (take three)
- Sort out a few Kconfig dependency issues for the rich set of RISC-V
non-coherent DMA support.
* tag 'renesas-fixes-for-v6.6-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: ARCH_R9A07G043 depends on !RISCV_ISA_ZICBOM
riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMT
riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENT
Link: https://lore.kernel.org/r/cover.1698312384.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARCH_R9A07G043 has its own non-standard global pool based DMA coherent
allocator, which conflicts with the remap based RISCV_ISA_ZICBOM version.
Add a proper dependency.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231018052654.50074-4-hch@lst.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
AngeloGioacchino Del Regno is stepping in as co-maintainer for the
MediaTek SoC platform and starts by sending some dts fixes for
the mt8195 platform that had been pending for a while.
On the ixp4xx platform, Krzysztof Halasa steps down as co-maintainer,
reflecting that Linus Walleij has been handling this on his own
for the past few years.
Generic RISC-V kernels are now marked as incompatible with the
RZ/Five platform that requires custom hacks both for managing
its DMA bounce buffers and for addressing low virtual memory.
Finally, there is one bugfix for the AMDTEE firmware driver
to prevent a use-after-free bug.
-----BEGIN PGP SIGNATURE-----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=Ukoh
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"AngeloGioacchino Del Regno is stepping in as co-maintainer for the
MediaTek SoC platform and starts by sending some dts fixes for the
mt8195 platform that had been pending for a while.
On the ixp4xx platform, Krzysztof Halasa steps down as co-maintainer,
reflecting that Linus Walleij has been handling this on his own for
the past few years.
Generic RISC-V kernels are now marked as incompatible with the RZ/Five
platform that requires custom hacks both for managing its DMA bounce
buffers and for addressing low virtual memory.
Finally, there is one bugfix for the AMDTEE firmware driver to prevent
a use-after-free bug"
* tag 'soc-fixes-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
IXP4xx MAINTAINERS entries
arm64: dts: mediatek: mt8195: Set DSU PMU status to fail
arm64: dts: mediatek: fix t-phy unit name
arm64: dts: mediatek: mt8195-demo: update and reorder reserved memory regions
arm64: dts: mediatek: mt8195-demo: fix the memory size to 8GB
MAINTAINERS: Add Angelo as MediaTek SoC co-maintainer
soc: renesas: Make ARCH_R9A07G043 (riscv version) depend on NONPORTABLE
tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
Randy reported a randconfig build issue against linux-next:
WARNING: unmet direct dependencies detected for ERRATA_ANDES
Depends on [n]: RISCV_ALTERNATIVE [=n] && RISCV_SBI [=y]
Selected by [y]:
- ARCH_R9A07G043 [=y] && SOC_RENESAS [=y] && RISCV [=y] && NONPORTABLE [=y] && RISCV_SBI [=y]
../arch/riscv/errata/andes/errata.c:59:54: warning: 'struct alt_entry' declared inside parameter list will not be visible outside of this definition or declaration
59 | void __init_or_module andes_errata_patch_func(struct alt_entry *begin, struct alt_entry *end,
On RISC-V, alternatives are not usable in XIP kernels, which this
randconfig happened to select. Rather than add a check for whether
alternatives are available before selecting the ERRATA_ANDES config
option, rework the R9A07G043 Kconfig entry to depend on the
configuration options required to support its non-standard cache
coherency implementation.
Without these options enabled, the SoC is effectively non-functional to
begin with, so there's an extra benefit in preventing the creation of
non-functional kernels.
The "if RISCV_DMA_NONCOHERENT" can be dropped, as ERRATA_ANDES_CMO will
select it.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/all/09a6b0f0-76a1-45e3-ab52-329c47393d1d@infradead.org/
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231012-pouch-parkway-7d26c04b3300@spud
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Drew found "CONFIG_DMA_GLOBAL_POOL=y causes ADMA buffer alloc to fail"
the log looks like:
mmc0: Unable to allocate ADMA buffers - falling back to standard DMA
The logic is: generic riscv defconfig selects ARCH_RENESAS then
ARCH_R9A07G043 which selects DMA_GLOBAL_POOL, which assumes all
non-dma-coherent riscv platforms have a dma global pool, this assumption
seems not correct. And I believe DMA_GLOBAL_POOL should not be
selected by ARCH_SOCFAMILIY, instead, only ARCH under some specific
conditions can select it globaly, for example NOMMU ARM and so on,
because it's designed for special cases such as "nommu cases where
non-cacheable memory lives in a fixed place in the physical address
map" as pointed out by Robin.
Fix the issue by making ARCH_R9A07G043 (riscv version) depend on
NONPORTABLE, thus generic defconfig won't select ARCH_R9A07G043 by
default. And even for random config case, there will be less debug
effort once we see NONPORTABLE is enabled.
Reported-by: Drew Fustini <dfustini@baylibre.com>
Closes: https://lore.kernel.org/linux-riscv/ZRuamJuShOnvP1pr@x1/
Fixes: 484861e09f ("soc: renesas: Kconfig: Select the required configs for RZ/Five SoC")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Drew Fustini <dfustini@baylibre.com>
Link: https://lore.kernel.org/r/20231004150856.2540-1-jszhang@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The syscon poweroff and reboot nodes logically belong to the Power
Management Unit so populate possible children.
Without it, the reboot/poweroff feature becomes unavailable.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now, "loongson,ls2k0500-pmc" is used as fallback compatible, so the
ls2k1000 compatible in the driver can be dropped directly.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since commit 67694c076b ("soc: loongson2_pm: add power management
support"), the Loongson-2K PM driver was added, but it didn't update the
Kconfig entry for the INPUT dependency, leading to build errors, so
update the Kconfig entry to depend on INPUT.
/opt/crosstool/gcc-13.2.0-nolibc/loongarch64-linux/bin/loongarch64-linux-ld:
drivers/soc/loongson/loongson2_pm.o: in function `loongson2_power_button_init':
/work/lnx/next/linux-next-20230825/LOONG64/../drivers/soc/loongson/loongson2_pm.c:101:(.text+0x350): undefined reference to `input_allocate_device'
/opt/crosstool/gcc-13.2.0-nolibc/loongarch64-linux/bin/loongarch64-linux-ld:
/work/lnx/next/linux-next-20230825/LOONG64/../drivers/soc/loongson/loongson2_pm.c:109:(.text+0x3dc): undefined reference to `input_set_capability'
/opt/crosstool/gcc-13.2.0-nolibc/loongarch64-linux/bin/loongarch64-linux-ld:
/work/lnx/next/linux-next-20230825/LOONG64/../drivers/soc/loongson/loongson2_pm.c:111:(.text+0x3e4): undefined reference to `input_register_device'
/opt/crosstool/gcc-13.2.0-nolibc/loongarch64-linux/bin/loongarch64-linux-ld:
/work/lnx/next/linux-next-20230825/LOONG64/../drivers/soc/loongson/loongson2_pm.c:125:(.text+0x3fc): undefined reference to `input_free_device'
/opt/crosstool/gcc-13.2.0-nolibc/loongarch64-linux/bin/loongarch64-linux-ld: drivers/soc/loongson/loongson2_pm.o: in function `input_report_key':
/work/lnx/next/linux-next-20230825/LOONG64/../include/linux/input.h:425:(.text+0x58c): undefined reference to `input_event'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 836fb30949 ("soc: imx8m: Enable OCOTP clock before reading the
register") added configuration to enable the OCOTP clock before
attempting to read from the associated registers.
This same kexec issue is present with the imx8m SoCs that use the
imx8mm_soc_uid function (e.g. imx8mp). This requires the imx8mm_soc_uid
function to configure the OCOTP clock before accessing the associated
registers. This change implements the same clock enable functionality
that is present in the imx8mq_soc_revision function for the
imx8mm_soc_uid function.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fixes: 836fb30949 ("soc: imx8m: Enable OCOTP clock before reading the register")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Prabhakar <prabhakar.csengg@gmail.com> says:
From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
non-coherent DMA support for AX45MP
====================================
On the Andes AX45MP core, cache coherency is a specification option so it
may not be supported. In this case DMA will fail. To get around with this
issue this patch series does the below:
1] Andes alternative ports is implemented as errata which checks if the
IOCP is missing and only then applies to CMO errata. One vendor specific
SBI EXT (ANDES_SBI_EXT_IOCP_SW_WORKAROUND) is implemented as part of
errata.
Below are the configs which Andes port provides (and are selected by
RZ/Five):
- ERRATA_ANDES
- ERRATA_ANDES_CMO
OpenSBI patch supporting ANDES_SBI_EXT_IOCP_SW_WORKAROUND SBI is now
part v1.3 release.
2] Andes AX45MP core has a Programmable Physical Memory Attributes (PMA)
block that allows dynamic adjustment of memory attributes in the runtime.
It contains a configurable amount of PMA entries implemented as CSR
registers to control the attributes of memory locations in interest.
OpenSBI configures the PMA regions as required and creates a reserve memory
node and propagates it to the higher boot stack.
Currently OpenSBI (upstream) configures the required PMA region and passes
this a shared DMA pool to Linux.
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
pma_resv0@58000000 {
compatible = "shared-dma-pool";
reg = <0x0 0x58000000 0x0 0x08000000>;
no-map;
linux,dma-default;
};
};
The above shared DMA pool gets appended to Linux DTB so the DMA memory
requests go through this region.
3] We provide callbacks to synchronize specific content between memory and
cache.
4] RZ/Five SoC selects the below configs
- AX45MP_L2_CACHE
- DMA_GLOBAL_POOL
- ERRATA_ANDES
- ERRATA_ANDES_CMO
----------x---------------------x--------------------x---------------x----
* b4-shazam-merge:
soc: renesas: Kconfig: Select the required configs for RZ/Five SoC
cache: Add L2 cache management for Andes AX45MP RISC-V core
dt-bindings: cache: andestech,ax45mp-cache: Add DT binding documentation for L2 cache controller
riscv: mm: dma-noncoherent: nonstandard cache operations support
riscv: errata: Add Andes alternative ports
riscv: asm: vendorid_list: Add Andes Technology to the vendors list
Link: https://lore.kernel.org/r/20230818135723.80612-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
changes to the clk framework this time around. That's probably because everyone
was on vacation (yours truly included). We did lose a couple clk drivers this
time around because nobody was using those devices. That skews the diffstat a
bit, but either way, nothing looks out of the ordinary here. The usual suspects
are chugging along adding support for more SoCs and fixing bugs.
If I had to choose, I'd say the theme for the past few months has been
"polish". There's quite a few patches that migrate to
devm_platform_ioremap_resource() in here. And there's more than a handful of
patches that move the NR_CLKS define from the DT binding header to the driver.
There's even patches that migrate drivers to use clk_parent_data and clk_hw to
describe clk tree topology. It seems that the spring (summer?) cleaning bug got
some folks, or the semiconductor shortage finally hit the software side.
New Drivers:
- StarFive JH7110 SoC clock drivers
- Qualcomm IPQ5018 Global Clock Controller driver
- Versa3 clk generator to support 48KHz playback/record with audio codec on
RZ/G2L SMARC EVK
Removed Drivers:
- Remove non-OF mmp clk drivers
- Remove OXNAS clk driver
Updates:
- Add __counted_by to struct clk_hw_onecell_data and struct spmi_pmic_div_clk_cc
- Move defines for numbers of clks (NR_CLKS) from DT headers to drivers
- Introduce kstrdup_and_replace() and use it
- Add PLL rates for Rockchip rk3568
- Add the display clock tree for Rockchip rv1126
- Add Audio Clock Generator (ADG) clocks on Renesas R-Car Gen3 and RZ/G2 SoCs
- Convert sun9i-mmc clock to use devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c
- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for Allwinner NKM clocks, i.e. consider alternative
parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for Allwinner A64 pll-mipi
- Support finding closest (as opposed to closest but not higher) clock rate
for NM, NKM, mux and div type clocks, as use it for Allwinner A64 pll-video0
- Prefer current parent rate if able to generate ideal clock rate for Allwinner NKM clocks
- Clean up Qualcomm SMD RPM driver, with interconnect bus clocks moved out to
the interconnect drivers
- Fix various PM runtime bugs across many Qualcomm clk drivers
- Migrate Qualcomm MDM9615 is to parent_hw and parent_data
- Add network related resets on Qualcomm IPQ4019
- Add a couple missing USB related clocks to Qualcomm IPQ9574
- Add missing gpll0_sleep_clk_src to Qualcomm MSM8917 global clock controller
- In the Qualcomm QDU1000 global clock controller, GDSCs, clkrefs, and GPLL1 are
added, while PCIe pipe clock, SDCC rcg ops are corrected
- Add missing GDSCs to and correct GDSCs for the SC8280XP global clock controller driver
- Support retention for the Qualcomm SC8280XP display clock controller GDSCs.
- Qualcommm's SDCC apps_clk_src is marked with CLK_OPS_PARENT_ENABLE to fix
issues with missing parent clocks across sc7180, sm7150, sm6350 and sm8250,
while sm8450 is corrected to use floor ops
- Correct Qualcomm SM6350 GPU clock controller's clock supplies
- Drop unwanted clocks from the Qualcomm IPQ5332 GCC driver
- Add missing OXILICX GDSC to Qualcomm MSM8226 GCC
- Change the delay in the Qualcomm reset controller to fsleep() for correctness
- Extend the Qualcomm SM83550 Video clock controller to support SC8280XP
- Add graphics clock support on Renesas RZ/G2M, RZ/G2N, RZ/G2E, and R-Car H3,
M3-W, and M3-N SoCs
- Add Clocked Serial Interface (CSI) clocks on Renesas RZ/V2M
- Add PWM (MTU3) clock and reset on Renesas RZ/G2UL and RZ/Five
- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() implementation for i.MX GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource()
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init()
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for i.MX PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from i.MX PLL14xx rate table to allow
glitch free switching
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAmTv2wkRHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSW1LRAAuHR2HoyB4bRHmCa1bfOfYYDfSWsBWEav
tWIfBl86Nl/Je50Gk2NJ9vqU5OPqRZ57TIniijHHoX5n7/kYcr8KVmlomY07hUeg
CzWyothkxg4k7+rQwVAWvmlR2YAVwzHDKcwq7gkMZOnW/y26LXip99cjopu2CJLx
zVwTgvWollmd4KVlicnAlx4zUjgNkWR24iA4Lcf5ir+Dr6FYNjxLI+akBA8EPxxi
wLixZbScgBSgpGn6KVgoFhclCToPS0gt5m6HfQxJ/svOCU54l+jRKpzkNZGWvyu4
A8t3CRrwL2iS/mfCGk2yRlaKySoLLpjlpW1AI7fHTWbG2P6p8ZphtN7jOeeAEsbq
TNpzWEjtY6B/lfRzxxINXkrtLaqmlnFY/P5np5fDrf/61gRFxLFQemyRdY/xCSJf
Kwq8ja1mrSGWoDGG9XhDqTf9Yek9LRObNzlDrEmn/i/qLTcxhOIz58pzHg4iAlx5
9HDtnJ8hKg4uE1TtT12Bmasb1+WzG7GYYESNfKWZhCvbRqEUzcDOHk7xpwYa1ffx
yZIgMs7Sb/exNW8LMPYmgnyj/f9eo5IdjiQvune+Zy5NrdzfyN6Sf/LSibrqCF2z
X5aFHqQrR8+PifD+se+g5HPa0ezSmBIhXzYUTOC6f+nywlrJjhwDXPDYI6Lcd//p
r4mpOmJS+G4=
=h2Jz
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"This pull request is full of clk driver changes. In fact, there aren't
any changes to the clk framework this time around. That's probably
because everyone was on vacation (yours truly included). We did lose a
couple clk drivers this time around because nobody was using those
devices. That skews the diffstat a bit, but either way, nothing looks
out of the ordinary here. The usual suspects are chugging along adding
support for more SoCs and fixing bugs.
If I had to choose, I'd say the theme for the past few months has been
"polish". There's quite a few patches that migrate to
devm_platform_ioremap_resource() in here. And there's more than a
handful of patches that move the NR_CLKS define from the DT binding
header to the driver. There's even patches that migrate drivers to use
clk_parent_data and clk_hw to describe clk tree topology. It seems
that the spring (summer?) cleaning bug got some folks, or the
semiconductor shortage finally hit the software side.
New Drivers:
- StarFive JH7110 SoC clock drivers
- Qualcomm IPQ5018 Global Clock Controller driver
- Versa3 clk generator to support 48KHz playback/record with audio
codec on RZ/G2L SMARC EVK
Removed Drivers:
- Remove non-OF mmp clk drivers
- Remove OXNAS clk driver
Updates:
- Add __counted_by to struct clk_hw_onecell_data and struct
spmi_pmic_div_clk_cc
- Move defines for numbers of clks (NR_CLKS) from DT headers to
drivers
- Introduce kstrdup_and_replace() and use it
- Add PLL rates for Rockchip rk3568
- Add the display clock tree for Rockchip rv1126
- Add Audio Clock Generator (ADG) clocks on Renesas R-Car Gen3 and
RZ/G2 SoCs
- Convert sun9i-mmc clock to use
devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c
- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for Allwinner NKM clocks, i.e.
consider alternative parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for Allwinner A64 pll-mipi
- Support finding closest (as opposed to closest but not higher)
clock rate for NM, NKM, mux and div type clocks, as use it for
Allwinner A64 pll-video0
- Prefer current parent rate if able to generate ideal clock rate for
Allwinner NKM clocks
- Clean up Qualcomm SMD RPM driver, with interconnect bus clocks
moved out to the interconnect drivers
- Fix various PM runtime bugs across many Qualcomm clk drivers
- Migrate Qualcomm MDM9615 is to parent_hw and parent_data
- Add network related resets on Qualcomm IPQ4019
- Add a couple missing USB related clocks to Qualcomm IPQ9574
- Add missing gpll0_sleep_clk_src to Qualcomm MSM8917 global clock
controller
- In the Qualcomm QDU1000 global clock controller, GDSCs, clkrefs,
and GPLL1 are added, while PCIe pipe clock, SDCC rcg ops are
corrected
- Add missing GDSCs to and correct GDSCs for the SC8280XP global
clock controller driver
- Support retention for the Qualcomm SC8280XP display clock
controller GDSCs.
- Qualcommm's SDCC apps_clk_src is marked with CLK_OPS_PARENT_ENABLE
to fix issues with missing parent clocks across sc7180, sm7150,
sm6350 and sm8250, while sm8450 is corrected to use floor ops
- Correct Qualcomm SM6350 GPU clock controller's clock supplies
- Drop unwanted clocks from the Qualcomm IPQ5332 GCC driver
- Add missing OXILICX GDSC to Qualcomm MSM8226 GCC
- Change the delay in the Qualcomm reset controller to fsleep() for
correctness
- Extend the Qualcomm SM83550 Video clock controller to support
SC8280XP
- Add graphics clock support on Renesas RZ/G2M, RZ/G2N, RZ/G2E, and
R-Car H3, M3-W, and M3-N SoCs
- Add Clocked Serial Interface (CSI) clocks on Renesas RZ/V2M
- Add PWM (MTU3) clock and reset on Renesas RZ/G2UL and RZ/Five
- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() implementation for i.MX GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource()
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init()
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for i.MX PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from i.MX PLL14xx rate table to
allow glitch free switching"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (207 commits)
clk: qcom: Fix SM_GPUCC_8450 dependencies
clk: lmk04832: Support using PLL1_LD as SPI readback pin
clk: lmk04832: Don't disable vco clock on probe fail
clk: lmk04832: Set missing parent_names for output clocks
clk: mvebu: Convert to devm_platform_ioremap_resource()
clk: nuvoton: Convert to devm_platform_ioremap_resource()
clk: socfpga: agilex: Convert to devm_platform_ioremap_resource()
clk: ti: Use devm_platform_get_and_ioremap_resource()
clk: mediatek: Convert to devm_platform_ioremap_resource()
clk: hsdk-pll: Convert to devm_platform_ioremap_resource()
clk: gemini: Convert to devm_platform_ioremap_resource()
clk: fsl-sai: Convert to devm_platform_ioremap_resource()
clk: bm1880: Convert to devm_platform_ioremap_resource()
clk: axm5516: Convert to devm_platform_ioremap_resource()
clk: actions: Convert to devm_platform_ioremap_resource()
clk: cdce925: Remove redundant of_match_ptr()
clk: pxa910: Move number of clocks to driver source
clk: pxa1928: Move number of clocks to driver source
clk: pxa168: Move number of clocks to driver source
clk: mmp2: Move number of clocks to driver source
...
These are all minor cleanups for platform specific code in arch/arm/
and some of the associated drivers. The majority of these are work
done by Rob Herring to improve the way devicetreee header files
are handled.
-----BEGIN PGP SIGNATURE-----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=c9NM
-----END PGP SIGNATURE-----
Merge tag 'soc-arm-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These are all minor cleanups for platform specific code in arch/arm/
and some of the associated drivers. The majority of these are work
done by Rob Herring to improve the way devicetreee header files are
handled"
* tag 'soc-arm-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (49 commits)
ARM: davinci: Drop unused includes
ARM: s5pv210: Explicitly include correct DT includes
ARM: dove: Drop unused includes
ARM: mvebu: Explicitly include correct DT includes
Documentation/process: maintainer-soc: document dtbs_check requirement for Samsung
MAINTAINER: samsung: document dtbs_check requirement for Samsung
Documentation/process: maintainer-soc: add clean platforms profile
MAINTAINERS: soc: reference maintainer profile
ARM: nspire: Remove unused header file mmio.h
ARM: nspire: Use syscon-reboot to handle restart
soc: fsl: Explicitly include correct DT includes
soc: xilinx: Explicitly include correct DT includes
soc: sunxi: Explicitly include correct DT includes
soc: rockchip: Explicitly include correct DT includes
soc: mediatek: Explicitly include correct DT includes
soc: aspeed: Explicitly include correct DT includes
firmware: Explicitly include correct DT includes
bus: Explicitly include correct DT includes
ARM: spear: Explicitly include correct DT includes
ARM: mvebu: Explicitly include correct DT includes
...
The main change this time is the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together. Ulf Hansson is taking over maintainership for
these and is sending a separate pull request with the same commits,
but they are in the soc drivers tree to avoid conflicts against other
soc driver patches.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other firmware
drivers.
On the soc driver side, the updates are mostly cleanups across a number
of Arm platforms. On driver for loongarch adds power management for DT
based systems, another driver is for HiSilicon's Arm server chips with
their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform.
-----BEGIN PGP SIGNATURE-----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=xmHW
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main change this time was the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other
firmware drivers.
On the soc driver side, the updates are mostly cleanups across a
number of Arm platforms. On driver for loongarch adds power management
for DT based systems, another driver is for HiSilicon's Arm server
chips with their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform"
* tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (136 commits)
bus: fsl-mc: Use common ranges functions
soc: kunpeng_hccs: fix some sparse warnings about incorrect type
soc: loongson2_pm: add power management support
soc: dt-bindings: add loongson-2 pm
soc: rockchip: grf: Fix SDMMC not working on RK3588 with bus-width > 1
genpd: rockchip: Add PD_VO entry for rv1126
bus: ti-sysc: Fix cast to enum warning
soc: kunpeng_hccs: add MAILBOX dependency
MAINTAINERS: remove OXNAS entry
dt-bindings: interrupt-controller: arm,versatile-fpga-irq: mark oxnas compatible as deprecated
irqchip: irq-versatile-fpga: remove obsolete oxnas compatible
soc: qcom: aoss: Tidy up qmp_send() callers
soc: qcom: aoss: Format string in qmp_send()
soc: qcom: aoss: Move length requirements from caller
soc: kunpeng_hccs: fix size_t format string
soc: ti: k3-socinfo.c: Add JTAG ID for AM62PX
dt-bindings: firmware: qcom: scm: Updating VMID list
firmware: imx: scu-irq: support identifying SCU wakeup source from sysfs
firmware: imx: scu-irq: enlarge the IMX_SC_IRQ_NUM_GROUP
firmware: imx: scu-irq: add imx_scu_irq_get_status
...
and starts moving some of the corresponding code in there.
We have currently ~60 users of the genpd provider interface, which are
sprinkled across various subsystems. To release some burden from the soc
maintainers (Arnd Bergmann, etc) in particular, but also to gain a better
overall view of what goes on in the area, I will help out with maintenance.
-----BEGIN PGP SIGNATURE-----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=Vp8b
-----END PGP SIGNATURE-----
Merge tag 'genpd-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull ARM SoC generic power domain driver updates from Ulf Hansson:
"This adds a new subsystem for generic power domain providers in
drivers/genpd and starts moving some of the corresponding code in
there.
We have currently ~60 users of the genpd provider interface, which are
sprinkled across various subsystems. To release some burden from the
soc maintainers (Arnd Bergmann, etc) in particular, but also to gain a
better overall view of what goes on in the area, I will help out with
maintenance"
[ I find the "genpd" name singularly uninformative, so we'll probably
end up moving this driver subsystem somewhere else, but that's still
being discussed - Linus ]
* tag 'genpd-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (30 commits)
genpd: ti: Use for_each_node_with_property() simplify code logic
genpd: Explicitly include correct DT includes
genpd: imx: scu-pd: initialize is_off according to HW state
genpd: imx: scu-pd: Suppress bind attrs
genpd: imx: scu-pd: do not power off console if no_console_suspend
genpd: imx: scu-pd: add more PDs
genpd: imx: scu-pd: enlarge PD range
genpd: imx: relocate scu-pd under genpd
MAINTAINERS: adjust file entry in STARFIVE JH71XX PMU CONTROLLER DRIVER
genpd: Makefile: build imx
genpd: move owl-sps-helper.c from drivers/soc
soc: starfive: remove stale Makefile entry
ARM: ux500: Move power-domain driver to the genpd dir
ARM: ux500: Convert power-domain code into a regular platform driver
soc: xilinx: Move power-domain driver to the genpd dir
soc: ti: Mover power-domain drivers to the genpd dir
soc: tegra: Move powergate-bpmp driver to the genpd dir
soc: sunxi: Move power-domain driver to the genpd dir
soc: starfive: Move the power-domain driver to the genpd dir
soc: samsung: Move power-domain driver to the genpd dir
...
- Carve out the new CONFIG_LIST_HARDENED as a more focused subset of
CONFIG_DEBUG_LIST (Marco Elver).
- Fix kallsyms lookup failure under Clang LTO (Yonghong Song).
- Clarify documentation for CONFIG_UBSAN_TRAP (Jann Horn).
- Flexible array member conversion not carried in other tree (Gustavo
A. R. Silva).
- Various strlcpy() and strncpy() removals not carried in other trees
(Azeem Shaikh, Justin Stitt).
- Convert nsproxy.count to refcount_t (Elena Reshetova).
- Add handful of __counted_by annotations not carried in other trees,
as well as an LKDTM test.
- Fix build failure with gcc-plugins on GCC 14+.
- Fix selftests to respect SKIP for signal-delivery tests.
- Fix CFI warning for paravirt callback prototype.
- Clarify documentation for seq_show_option_n() usage.
-----BEGIN PGP SIGNATURE-----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=9ZWP
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"As has become normal, changes are scattered around the tree (either
explicitly maintainer Acked or for trivial stuff that went ignored):
- Carve out the new CONFIG_LIST_HARDENED as a more focused subset of
CONFIG_DEBUG_LIST (Marco Elver)
- Fix kallsyms lookup failure under Clang LTO (Yonghong Song)
- Clarify documentation for CONFIG_UBSAN_TRAP (Jann Horn)
- Flexible array member conversion not carried in other tree (Gustavo
A. R. Silva)
- Various strlcpy() and strncpy() removals not carried in other trees
(Azeem Shaikh, Justin Stitt)
- Convert nsproxy.count to refcount_t (Elena Reshetova)
- Add handful of __counted_by annotations not carried in other trees,
as well as an LKDTM test
- Fix build failure with gcc-plugins on GCC 14+
- Fix selftests to respect SKIP for signal-delivery tests
- Fix CFI warning for paravirt callback prototype
- Clarify documentation for seq_show_option_n() usage"
* tag 'hardening-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
LoadPin: Annotate struct dm_verity_loadpin_trusted_root_digest with __counted_by
kallsyms: Change func signature for cleanup_symbol_name()
kallsyms: Fix kallsyms_selftest failure
nsproxy: Convert nsproxy.count to refcount_t
integrity: Annotate struct ima_rule_opt_list with __counted_by
lkdtm: Add FAM_BOUNDS test for __counted_by
Compiler Attributes: counted_by: Adjust name and identifier expansion
um: refactor deprecated strncpy to memcpy
um: vector: refactor deprecated strncpy
alpha: Replace one-element array with flexible-array member
hardening: Move BUG_ON_DATA_CORRUPTION to hardening options
list: Introduce CONFIG_LIST_HARDENED
list_debug: Introduce inline wrappers for debug checks
compiler_types: Introduce the Clang __preserve_most function attribute
gcc-plugins: Rename last_stmt() for GCC 14+
selftests/harness: Actually report SKIP for signal tests
x86/paravirt: Fix tlb_remove_table function callback prototype warning
EISA: Replace all non-returning strlcpy with strscpy
perf: Replace strlcpy with strscpy
um: Remove strlcpy declaration
...
Compatible and clock handling in the Qualcomm SCM driver is cleaned up,
together with a couple stylistic cleanups and transition to mark
exported symbols GPL only.
An abstraction for the RPM subsystem is introduced, to make align the
structure of the SMD and GLINK nodes thereof with the structure when a
remoteproc is involved. This is done to facilitate associating
additional entities with the RPM subsystem.
The qmp_send() API is modified to not expose hardware requirements onto
the client drivers, and then further extended to allow command
formatting directly in the API, to facilitate this typical use case.
In the Qualcomm Command DB driver, NUL characters previously included in
identifiers are dropped from the debugfs, to facilitate scripting.
The thresholds of the BWMON driver are simplified to avoid hard coded
starting values.
The OCMEM driver is updated with some cleanups and fixes, and addition
of MSM8226 support.
PMIC_GLINK gains support for retimer switches, safe mode is selected
when the cable is disconnected from altmode and the same is enabled for
SM8550.
An off-by-one string length check is corrected in the QMI encoder
decoder library.
The RPMh tracepoints are extended to include the state of the request,
to provide needed context in the traced events.
The series from Ulf creating a genpd framework is integrated, to
facilitate the other changes to the cpr, rpmpd and rpmhpd driver.
SDX75 support is added to the rpmhpd driver, and the rpmpd driver is
extended with the same sync_state logic found in the rpmhpd driver.
The socinfo driver gains knowledge about SM4450 and SM7125, the IPQ5019
platform is dropped.
Clock handling in the GSBI driver is cleaned up with the use of
devm_clk_get_enabled().
The list of VMIDs defined for the SCM assign memory interface is
extended.
-----BEGIN PGP SIGNATURE-----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=SEyF
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=RpyB
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
Qualcomm driver updates for v6.6
Compatible and clock handling in the Qualcomm SCM driver is cleaned up,
together with a couple stylistic cleanups and transition to mark
exported symbols GPL only.
An abstraction for the RPM subsystem is introduced, to make align the
structure of the SMD and GLINK nodes thereof with the structure when a
remoteproc is involved. This is done to facilitate associating
additional entities with the RPM subsystem.
The qmp_send() API is modified to not expose hardware requirements onto
the client drivers, and then further extended to allow command
formatting directly in the API, to facilitate this typical use case.
In the Qualcomm Command DB driver, NUL characters previously included in
identifiers are dropped from the debugfs, to facilitate scripting.
The thresholds of the BWMON driver are simplified to avoid hard coded
starting values.
The OCMEM driver is updated with some cleanups and fixes, and addition
of MSM8226 support.
PMIC_GLINK gains support for retimer switches, safe mode is selected
when the cable is disconnected from altmode and the same is enabled for
SM8550.
An off-by-one string length check is corrected in the QMI encoder
decoder library.
The RPMh tracepoints are extended to include the state of the request,
to provide needed context in the traced events.
The series from Ulf creating a genpd framework is integrated, to
facilitate the other changes to the cpr, rpmpd and rpmhpd driver.
SDX75 support is added to the rpmhpd driver, and the rpmpd driver is
extended with the same sync_state logic found in the rpmhpd driver.
The socinfo driver gains knowledge about SM4450 and SM7125, the IPQ5019
platform is dropped.
Clock handling in the GSBI driver is cleaned up with the use of
devm_clk_get_enabled().
The list of VMIDs defined for the SCM assign memory interface is
extended.
* tag 'qcom-drivers-for-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (52 commits)
soc: qcom: aoss: Tidy up qmp_send() callers
soc: qcom: aoss: Format string in qmp_send()
soc: qcom: aoss: Move length requirements from caller
dt-bindings: firmware: qcom: scm: Updating VMID list
dt-bindings: qcom: Update RPMHPD entries for some SoCs
soc: qcom: qmi_encdec: Restrict string length in decode
soc: qcom: smem: Fix incompatible types in comparison
soc: qcom: ocmem: add missing clk_disable_unprepare() in ocmem_dev_probe()
soc: qcom: socinfo: Add SoC ID for SM7125
dt-bindings: arm: qcom,ids: Add SoC ID for SM7125
dt-bindings: arm: qcom,ids: drop the IPQ5019 SoC ID
soc: qcom: socinfo: drop the IPQ5019 SoC ID
soc: qcom: socinfo: add SM4450 ID
dt-bindings: arm: qcom,ids: add SoC ID for SM4450
soc: qcom: pmic_glink: enable altmode for SM8550
soc: qcom: pmic_glink_altmode: add retimer-switch support
soc: qcom: pmic_glink_altmode: handle safe mode when disconnect
soc: qcom: rpmhpd: Add SDX75 power domains
dt-bindings: power: qcom,rpmpd: Add compatible for sdx75
genpd: Makefile: build imx
...
Link: https://lore.kernel.org/r/20230818023338.2484467-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
sdmmc and jtag for rk3588 (makes sdmmc unreliable).
This includes the shared genpd-v6.5-rc1-1 tag from Ulf Hansson, which moves
the powerdomain drivers into a new genpd subsystem.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAmTdQxUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgaRgB/41U/lA1H0hIfXBKKBXFEDYkQMC1qEEtDnU
pi8L6Bp44Gb5JbrD4wrNMc9AUJokxC1zGEVmwpySXNOy3ma0DQRPPKNQMNo8gcae
R8bZPbpdvkBBY6HMeFI0/c0+B3qU0G/RBfaMMe0edPlaeLFz8j8TUotUJo4rGh20
RoA2Dir7/YWN1S0EIOwJVRzYnr9vG7rGJsceabyYH/liDFs7neEgCDi9LWwNIBbL
5ANWM7UytIOsZOrPOegLHLgsPyYvccHgKCgctCPt6k04/9ZBTwp6pFyBtUtd91GW
oAL7SgF5tbkDYysj3nwZGOzCUIUVlxMTs6szTge4WuzGVOhXOZrn
=5C7a
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Nt2J
-----END PGP SIGNATURE-----
Merge tag 'v6.6-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/drivers
PD_VO powerdomain for rv1126 and disabling of the automatic switch between
sdmmc and jtag for rk3588 (makes sdmmc unreliable).
This includes the shared genpd-v6.5-rc1-1 tag from Ulf Hansson, which moves
the powerdomain drivers into a new genpd subsystem.
* tag 'v6.6-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: grf: Fix SDMMC not working on RK3588 with bus-width > 1
genpd: rockchip: Add PD_VO entry for rv1126
Link: https://lore.kernel.org/r/40318909.XM6RcZxFsP@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Loongson-2's power management controller was ACPI, supports ACPI
S2Idle (Suspend To Idle), ACPI S3 (Suspend To RAM), ACPI S4 (Suspend To
Disk), ACPI S5 (Soft Shutdown) and supports multiple wake-up methods
(USB, GMAC, PWRBTN, etc.). This driver was to add power management
controller support that base on dts for Loongson-2 series SoCs.
Co-developed-by: Liu Yun <liuyun@loongson.cn>
Signed-off-by: Liu Yun <liuyun@loongson.cn>
Co-developed-by: Liu Peibao <liupeibao@loongson.cn>
Signed-off-by: Liu Peibao <liupeibao@loongson.cn>
Cc: soc@kernel.org
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20230803063703.5659-3-zhuyinbo@loongson.cn
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
RK3588 has the same issue as other earlier RK SoCs. JTAG
functionality muxed to some SDMMC data pins causes issues with SDMMC
interface. Without this patch, I can only use SDMMC inteface
with bus-width = <1>. (JTAG is muxed to data pins D2 and D3)
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20230619011002.2249960-1-megi@xff.cz
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When the mailbox subsystem is disabled, the driver fails to link, so add
an explicit dependency. Some other drivers use 'select' here, but the
dependency seems more logical and more common.
Fixes: 886bdf9c88 ("soc: hisilicon: Support HCCS driver on Kunpeng SoC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With qmp_send() handling variable length messages and string formatting
he callers of qmp_send() can be cleaned up to not care about these
things.
Drop the QMP_MSG_LEN sized buffers and use the message formatting, as
appropriate.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230811205839.727373-5-quic_bjorande@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The majority of callers to qmp_send() composes the message dynamically
using some form of sprintf(), resulting in unnecessary complication and
stack usage.
By changing the interface of qmp_send() to take a format string and
arguments, the duplicated composition of the commands can be moved to a
single location.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230811205839.727373-4-quic_bjorande@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The existing implementation of qmp_send() requires the caller to provide
a buffer which is of word-aligned. The underlying reason for this is
that message ram only supports word accesses, but pushing this
requirement onto the clients results in the same boiler plate code
sprinkled in every call site.
By using a temporary buffer in qmp_send() we can hide the underlying
hardware limitations from the clients and allow them to pass their
NUL-terminates C string directly.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811205839.727373-2-quic_bjorande@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Printing a size_t using the %lu format string causes a warning on
architectures that define the type as 'unsigned int':
In file included from include/linux/device.h:15,
from include/linux/acpi.h:14,
from drivers/soc/hisilicon/kunpeng_hccs.c:25:
drivers/soc/hisilicon/kunpeng_hccs.c: In function 'hccs_get_bd_info':
drivers/soc/hisilicon/kunpeng_hccs.c:441:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
Use the correct %zu format instead.
Fixes: 886bdf9c88 ("soc: hisilicon: Support HCCS driver on Kunpeng SoC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing use of match_string() caused it to reject 'echo foo' due
to the implicitly appended newline, which was somewhat ergonomically
awkward and inconsistent with typical sysfs behavior. Using the
__sysfs_* variant instead provides more convenient and consistent
linefeed-agnostic behavior.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: c6807970c3 ("soc: aspeed: Add UART routing support")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230628083735.19946-2-zev@bewilderbeest.net
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230810122941.231085-1-joel@jms.id.au
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add C3 Power Domains
- Explicitly include correct DT includes in Amlogic SoC drivers
- fix to avoid potential NULL pointer dereference in meson_sm
- Merge of genpd-v6.5-rc1-1 to move genpd amlogic drivers
-----BEGIN PGP SIGNATURE-----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=eBDR
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=jJE/
-----END PGP SIGNATURE-----
Merge tag 'amlogic-drivers-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into soc/drivers
Amlogic drivers changes for v6.6:
- Add C3 Power Domains
- Explicitly include correct DT includes in Amlogic SoC drivers
- fix to avoid potential NULL pointer dereference in meson_sm
- Merge of genpd-v6.5-rc1-1 to move genpd amlogic drivers
* tag 'amlogic-drivers-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
firmware: meson_sm: fix to avoid potential NULL pointer dereference
soc: amlogic: Explicitly include correct DT includes
soc: c3: Add support for power domains controller
dt-bindings: power: add Amlogic C3 power domains
soc: amlogic: use name instead of index as criterion
Link: https://lore.kernel.org/r/77e328b5-0d47-36e8-f62d-c745df06fb87@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Cleanup remove callback in event driver
- Explicitly include correct DT header in power driver
- Fix logic around irq = 0 in power driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZMzgwgAKCRDKSWXLKUoM
IRRjAJ4kS4jzkdR/UN4xha2v9fhLQIEtOwCgheqMzg553ap53DXFOsHobL7WGvY=
=rkA5
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yxvn
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-soc-for-6.6' of https://github.com/Xilinx/linux-xlnx into soc/drivers
arm64: ZynqMP SoC changes for 6.6
- Cleanup remove callback in event driver
- Explicitly include correct DT header in power driver
- Fix logic around irq = 0 in power driver
* tag 'zynqmp-soc-for-6.6' of https://github.com/Xilinx/linux-xlnx:
soc: xilinx: Do not check for 0 return after calling platform_get_irq()
soc: xilinx: Explicitly include correct DT includes
driver: soc: xilinx: Convert to platform remove callback returning void
Link: https://lore.kernel.org/r/399efa45-df0a-4ec7-e25c-774bb8bf6fb4@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It contains:
- explicitly include correct DT includes from Rob
- one cleanup which removes unused extern declaration on atmel_tcb.h
-----BEGIN PGP SIGNATURE-----
iI8EABYIADcWIQTsZ8eserC1pmhwqDmejrg/N2X7/QUCZMx+PxkcY2xhdWRpdS5i
ZXpuZWFAZ21haWwuY29tAAoJEJ6OuD83Zfv9RHAA/jMPJ6uQKDDP9iYzJD4moCC2
H614pQHGJx8PLnxt7kPaAP4xrN1l9+Yo0+31r8bDSjGBksmOK0g262shKXgsY79G
AA==
=ab+a
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=8ksf
-----END PGP SIGNATURE-----
Merge tag 'at91-soc-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/arm
AT91 SoC updates for 6.6:
It contains:
- explicitly include correct DT includes from Rob
- one cleanup which removes unused extern declaration on atmel_tcb.h
* tag 'at91-soc-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: at91: Remove unused extern declarations
ARM: at91: Explicitly include correct DT includes
soc: microchip: Explicitly include correct DT includes
Link: https://lore.kernel.org/r/20230804044118.231478-1-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-23-d8de2cc88bff@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-22-d8de2cc88bff@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-21-d8de2cc88bff@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-20-d8de2cc88bff@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-19-d8de2cc88bff@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-18-d8de2cc88bff@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds JTAG ID info for the AM62PX so as to enable SoC detection in
kernel.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/20230811170127.250733-1-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
platform_get_resource_byname() and devm_ioremap_resource() can be
replaced by devm_platform_ioremap_resource_byname(), which can
simplify the code logic a bit, No functional change here.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230809081523.26196-1-zhangzekun11@huawei.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch creates chip, die and port directory based on the actual
hardware implementation of platform. Some sysfs entries under these
directories are created to query the health status and port information
of HCCS.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The Huawei Cache Coherence System (HCCS) is a multi-chip interconnection
bus protocol. This driver is aimed to support some features about HCCS on
Kunpeng SoC, like, querying the health status of HCCS.
This patch adds the probing of HCCS driver, and obtains all HCCS port
information by the dimension of chip and die on platform.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-21-d8de2cc88bff@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230714175124.4066972-1-robh@kernel.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230803-dt-header-cleanups-for-soc-v2-22-d8de2cc88bff@kernel.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
Merge the topic branch that introduces the genpd subsystem into the
Qualcomm soc driver tree, in order to deal with patches landed in the
Qualcomm rpmhpd driver already in this cycle.
The QMI TLV value for strings in a lot of qmi element info structures
account for null terminated strings with MAX_LEN + 1. If a string is
actually MAX_LEN + 1 length, this will cause an out of bounds access
when the NULL character is appended in decoding.
Fixes: 9b8a11e826 ("soc: qcom: Introduce QMI encoder/decoder")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Link: https://lore.kernel.org/r/20230801064712.3590128-1-quic_ipkumar@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This patch fixes the following sparse error:
drivers/soc/qcom/smem.c:738:30: error: incompatible types in comparison expression (different add ress spaces):
drivers/soc/qcom/smem.c:738:30: void *
drivers/soc/qcom/smem.c:738:30: void [noderef] __iomem *
In addr_in_range(), "base" is of type void __iomem *, converting
void *addr to the same type to fix above sparse error.
Fixes: 20bb6c9de1 ("soc: qcom: smem: map only partitions used by local HOST")
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Link: https://lore.kernel.org/r/20230801094807.4146779-1-chenjiahao16@huawei.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Drop the non-fatal probe deferral log for getting MSI domain.
This makes the kernel log clean and we do not get recurring logs
stating: "Failed to get MSI domain".
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20230728053356.31044-1-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the SoC ID entry for Qualcomm SM7125.
Signed-off-by: David Wronek <davidwronek@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230723190725.1619193-5-davidwronek@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the ID for the Qualcomm SM4450 SoC.
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230731080043.38552-7-quic_tengfan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Some boards have a retimer/redriver between the SuperSpeed
PHY and the USB-C connector to compensates signal integrity
losses mainly due to PCB & transmission cables.
Add support for an optional retimer-switch in the USB-C
connector graph.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230601-topic-sm8550-upstream-type-c-v5-2-9221cd300903@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230714175139.4067685-1-robh@kernel.org
[claudiu.beznea: added link]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
./drivers/soc/tegra/cbb/tegra-cbb.c:130:3-10: line 130 is redundant because platform_get_irq() already prints an error.
./drivers/soc/tegra/cbb/tegra-cbb.c:140:2-9: line 140 is redundant because platform_get_irq() already prints an error.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4879
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Moving only one of the two files in drivers/soc/actions to drivers/genpd
caused a link failure in allmodconfig, as drivers/genpd is entered
for compile testing, but drivers/soc/actions accidentally got skipped:
x86_64-linux-gnu-ld: vmlinux.o: in function `owl_sps_set_power':
owl-sps.c:(.text+0x16e259d): undefined reference to `owl_sps_set_pg'
Move the other one as well to allow build testing to work correctly.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After the only starfive driver was moved out to the genpd subsystem, we get
a build failure:
scripts/Makefile.build:41: drivers/soc/starfive/Makefile: No such file or directory
Fixes: f3fb16291f ("soc: starfive: Move the power-domain driver to the genpd dir")
Reported=by: kernel test robot <lkp@intel.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714175156.4068520-1-robh@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705122644.32236-1-frank.li@vivo.com
Signed-off-by: Nishanth Menon <nm@ti.com>
in gsbi_probe(), the return value of function clk_prepare_enable()
should be checked, since it may fail. using devm_clk_get_enabled()
instead of devm_clk_get() and clk_prepare_enable() can avoid this
problem.
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Link: https://lore.kernel.org/r/20230720140834.33557-1-ruc_gongyuanjun@163.com
[bjorn: Dropped unnecessary "ret" variable]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20230714175147.4068046-1-robh@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The blk-ctrl device is deliberately placed outside of the GPC power
domain as it needs to control the power sequencing of the blk-ctrl
domains together with the GPC domains.
Clock runtime PM works by operating on the clock parent device, which
doesn't translate into the neccessary GPC power domain action if the
clk parent is not part of the GPC power domain. Use the bus_power_device
as the parent for the clock to trigger the proper GPC domain actions on
clock runtime power management.
Fixes: 2cbee26e5d ("soc: imx: imx8mp-blk-ctrl: expose high performance PLL clock")
Reported-by: Yannic Moog <Y.Moog@phytec.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
icc_smd_rpm will do bus clock votes itself rather than taking the
unnecessary detour through the clock subsystem. However, it can only
do that after the clocks have been handed off and scaling has been
enabled in the RPM in clk-smd-rpm.
Move the icc_smd_rpm registration from smd-rpm.c to clk-smd-rpm.c
to avoid any possible races. icc_smd_rpm gets the driver data from
the smd-rpm device, so still register the platform device on the
smd-rpm parent device.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[Konrad: remove unrelated cleanups]
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-5-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714175142.4067795-1-robh@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To simplify with maintenance let's move the xilinx power-domain driver to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the ti power-domain drivers to the
new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Nishanth Menon <nm@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the powergate-bpmp driver to the
new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Note that, we leave the pmc driver in the soc directory for now, as it
looks like it may need some re-structuring before it's ready to be moved.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: <linux-tegra@vger.kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the sunxi power-domain driver to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: <linux-sunxi@lists.linux.dev>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the starfive power-domain driver to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Walker Chen <walker.chen@starfivetech.com>
Cc: Conor Dooley <conor@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the samsung power-domain driver to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: <linux-samsung-soc@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the rockchip power-domain driver to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: <linux-rockchip@lists.infradead.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the renesas power-domain drivers to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: <linux-renesas-soc@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the qcom power-domain drivers to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: <linux-arm-msm@vger.kernel.org>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a simple driver for the qcom,rpm-proc compatible that registers the
"smd-edge" and populates other children defined in the device tree.
Note that the DT schema belongs to the remoteproc subsystem while this
driver is added inside soc/qcom. I argue that the RPM *is* a remoteproc,
but as an implementation detail in Linux it can currently not benefit
from anything provided by the remoteproc subsystem. The RPM firmware is
usually already loaded and started by earlier components in the boot
chain and is not meant to be ever restarted.
To avoid breaking existing kernel configurations the driver is always
built when smd-rpm.c is also built. They belong closely together anyway.
To avoid build errors CONFIG_RPMSG_QCOM_SMD must be also built-in if
rpm-proc is.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230531-rpm-rproc-v3-9-a07dcdefd918@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Avoid having to look up a dummy item from SMEM to detect if it is
already available or if we need to defer probing.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230531-rpm-rproc-v3-7-a07dcdefd918@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There is an ever growing list of compatibles in the smd-rpm.c driver.
A fallback compatible would help here but would still require keeping
the current list around for backwards compatibility.
As an alternative, let's switch the driver to match the rpmsg_device_id
instead, which is always "rpm_requests" on all platforms. Add a check
to ensure that there is a device tree node defined for the device since
otherwise the of_platform_populate() call will operate on the root node (/).
Similar approaches with matching rpmsg_device_id are already used in
qcom_sysmon, qcom_glink_ssr, qrtr, and rpmsg_wwan_ctrl.
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM6375 (G-Link)
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230531-rpm-rproc-v3-4-a07dcdefd918@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fixup couple of misses in documentation. This squashes the following
warnings:
drivers/soc/ti/k3-ringacc.c:135: warning: Function parameter or member 'tdown_complete' not described in 'k3_ring_state'
drivers/soc/ti/k3-ringacc.c:238: warning: expecting prototype for struct k3_ringacc. Prototype was for struct k3_ringacc_soc_data instead
While at this, replace "w/a" to indicate workaround to help clarify.
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230621023442.275128-1-nm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
To simplify with maintenance let's move the mediatek power-domain drivers
to the new genpd directory. Going forward, patches are intended to be
managed through a separate git tree, according to MAINTAINERS.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <linux-mediatek@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the imx power-domain drivers to the
new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: <kernel@pengutronix.de>
Cc: <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the bcm power-domain drivers to the
new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
While moving the drivers, we end up with a directory for bcm63xx that only
contains a Kconfig file, which seems a bit silly. Let's therefore also move
the Kconfig options into the Kconfig file a directory above, as it allows
us to drop the directory too.
Cc: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-rpi-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the apple power-domain driver to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Hector Martin <marcan@marcan.st>
Cc: Sven Peter <sven@svenpeter.dev>
Cc: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Cc: <asahi@lists.linux.dev>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the amlogic power-domain drivers to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <linux-amlogic@lists.infradead.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify with maintenance let's move the action power-domain driver to
the new genpd directory. Going forward, patches are intended to be managed
through a separate git tree, according to MAINTAINERS.
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: <linux-actions@lists.infradead.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the only effect compared to returning
zero is that the core emits an error message. By converting to
.remove_new() (which is semantically equivalent to return 0 in
.remove()) this error message is suppressed which is a good thing as
xlnx_event_manager_remove() already emits an better error message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230628083636.684394-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
When tracing messages written to the RSC it's very useful to know the
type of TCS being targeted, in particular if/when the code borrows a
WAKE TCS for ACTIVE votes.
Add the "state" of the message to the traced information.
While at it, drop the "send-msg:" substring, as this is already captured
by the trace event itself.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230620230058.428833-1-quic_bjorande@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The debugfs dump of Command DB relies uses %*pEp to print the resource
identifiers, with escaping of non-printable characters.
But p (ESCAPE_NP) does not escape NUL characters, so for identifiers
less than 8 bytes in length the output will retain these.
This does not cause an issue while looking at the dump in the terminal
(no known complaints at least), but when programmatically consuming the
debugfs output the extra characters are unwanted.
Change the fixed 8-byte sizeof() to a dynamic strnlen() to avoid
printing these NUL characters.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230620213703.283583-1-quic_bjorande@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Some platforms such as msm8226 do not have an iface clk. Since clk_bulk
APIs don't offer to a way to treat some clocks as optional simply add
core_clk and iface_clk members to our drvdata.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20230506-msm8226-ocmem-v3-3-79da95a2581f@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use dev_err_probe in the driver probe function where useful, to simplify
getting PTR_ERR and to ensure the underlying errors are included in the
error message.
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20230506-msm8226-ocmem-v3-2-79da95a2581f@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since we're using these two macros to read a value from a register, we
need to use the FIELD_GET instead of the FIELD_PREP macro, otherwise
we're getting wrong values.
So instead of:
[ 3.111779] ocmem fdd00000.sram: 2 ports, 1 regions, 512 macros, not interleaved
we now get the correct value of:
[ 3.129672] ocmem fdd00000.sram: 2 ports, 1 regions, 2 macros, not interleaved
Fixes: 88c1e9404f ("soc: qcom: add OCMEM driver")
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20230506-msm8226-ocmem-v3-1-79da95a2581f@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Currently we use predefined initial threshold values. This works, but
does not really scale well with more and more SoCs gaining bwmon support,
as the necessary kickoff values may differ between platforms due to memory
type and/or controller setup.
All of the data we need for that is already provided in the device tree,
anyway.
Change the thresholds to:
* low = 0 (as we've been doing up until now)
* med = high = BW_MIN
Throughput going below the med threshold nudges bwmon into signaling
that we should slow down (e.g. if we inherited too high bandwidth
from the bootloader).
Throughput going above the high threshold nudges bwmon into signaling
that we should speed up so as not to choke the bus traffic due to
insufficient transfer rates.
F_MIN is a perfect initial value for both of these cases - if we go
above it (and there's a 99.99% chance it'll happen at boot time), we
should definitely make the memory go faster, whereas if we go below it,
we should slow down, no matter what performance state we were at before
(it's only possible for them to be >= FMIN).
This only changes the values programmed at probe time, as high and med
thresholds are updated at interrupt, also based on the OPP table from DT.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230610-topic-bwmon_opp-v2-1-0d25c1ce7dca@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the hardware
in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKcVw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynEIQCgzJgnMCB81mirXlY1ZpCSDFqN8KIAnjRc27/1
vnUzldMQGY/FiS549gD9
=G3yz
-----END PGP SIGNATURE-----
Merge tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the
hardware in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: host: xhci-plat: Set XHCI_STATE_REMOVING before resuming XHCI HC
usb: host: xhci: Do not re-initialize the XHCI HC if being removed
usb: typec: nb7vpq904m: fix CONFIG_DRM dependency
usbip: usbip_host: Replace strlcpy with strscpy
usb: dwc3: gadget: Propagate core init errors to UDC during pullup
USB: serial: option: add LARA-R6 01B PIDs
usb: ulpi: Make container_of() no-op in to_ulpi_dev()
usb: gadget: legacy: fix error return code in gfs_bind
usb: typec: fsa4480: add support for Audio Accessory Mode
usb: typec: fsa4480: rework mux & switch setup to handle more states
usb: typec: ucsi: call typec_set_mode on non-altmode partner change
USB: gadget: f_hid: make hidg_class a static const structure
USB: gadget: f_printer: make usb_gadget_class a static const structure
USB: mon: make mon_bin_class a static const structure
USB: gadget: udc: core: make udc_class a static const structure
USB: roles: make role_class a static const structure
dt-bindings: usb: dwc3: Add interrupt-names property support for wakeup interrupt
dt-bindings: usb: Add StarFive JH7110 USB controller
dt-bindings: usb: dwc3: Add IPQ9574 compatible
usb: cdns2: Fix spelling mistake in a trace message "Wakupe" -> "Wakeup"
...
No core changes this time.
New drivers:
- Tegra234 support.
- Qualcomm IPQ5018 support.
- Intel Meteor Lake-S support.
- Qualcomm SDX75 subdriver.
- Qualcomm SPMI-based PM8953 support.
Improvements:
- Fix up support for GPIO3 on the AXP209.
- Push-pull drive configuration support for the AT91 PIO4.
- Fix misc non-urgent bugs in the AMD driver.
- Misc non-urgent improved error handling.
- Misc janitorial and minor improvements.
-----BEGIN PGP SIGNATURE-----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=MMUo
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time
New drivers:
- Tegra234 support
- Qualcomm IPQ5018 support
- Intel Meteor Lake-S support
- Qualcomm SDX75 subdriver
- Qualcomm SPMI-based PM8953 support
Improvements:
- Fix up support for GPIO3 on the AXP209
- Push-pull drive configuration support for the AT91 PIO4
- Fix misc non-urgent bugs in the AMD driver
- Misc non-urgent improved error handling
- Misc janitorial and minor improvements"
* tag 'pinctrl-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: cherryview: Drop goto label
pinctrl: baytrail: invert if condition
pinctrl: baytrail: add warning for BYT_VAL_REG retrieval failure
pinctrl: baytrail: reduce scope of spinlock in ->dbg_show() hook
pinctrl: tegra: avoid duplicate field initializers
dt-bindings: pinctrl: qcom,sdx65-tlmm: add pcie_clkreq function
pinctrl: mlxbf3: remove broken Kconfig 'select'
pinctrl: spear: Remove unused of_gpio.h inclusion
pinctrl: lantiq: Remove unused of_gpio.h inclusion
pinctrl: at91-pio4: check return value of devm_kasprintf()
pinctrl: microchip-sgpio: check return value of devm_kasprintf()
pinctrl: freescale: Fix a memory out of bounds when num_configs is 1
pinctrl: intel: refine ->irq_set_type() hook
pinctrl: intel: refine ->set_mux() hook
pinctrl: baytrail: Use str_hi_lo() helper
lib/string_choices: Add str_high_low() helper
lib/string_helpers: Split out string_choices.h
lib/string_helpers: Add missing header files to MAINTAINERS database
pinctrl: npcm7xx: Add missing check for ioremap
pinctrl:sunplus: Add check for kmalloc
...
Nothing surprising in the SoC specific drivers, with the usual updates:
* Added or improved SoC driver support for Tegra234, Exynos4121, RK3588,
as well as multiple Mediatek and Qualcomm chips
* SCMI firmware gains support for multiple SMC/HVC transport and version
3.2 of the protocol
* Cleanups amd minor changes for the reset controller, memory controller,
firmware and sram drivers
* Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers
-----BEGIN PGP SIGNATURE-----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=zvLr
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Nothing surprising in the SoC specific drivers, with the usual
updates:
- Added or improved SoC driver support for Tegra234, Exynos4121,
RK3588, as well as multiple Mediatek and Qualcomm chips
- SCMI firmware gains support for multiple SMC/HVC transport and
version 3.2 of the protocol
- Cleanups amd minor changes for the reset controller, memory
controller, firmware and sram drivers
- Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers"
* tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (118 commits)
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
tee: optee: Use kmemdup() to replace kmalloc + memcpy
soc: qcom: geni-se: Do not bother about enable/disable of interrupts in secondary sequencer
dt-bindings: sram: qcom,imem: document qdu1000
soc: qcom: icc-bwmon: Fix MSM8998 count unit
dt-bindings: soc: qcom,rpmh-rsc: Require power-domains
soc: qcom: socinfo: Add Soc ID for IPQ5300
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300
soc: qcom: Fix a IS_ERR() vs NULL bug in probe
soc: qcom: socinfo: Add support for new fields in revision 19
soc: qcom: socinfo: Add support for new fields in revision 18
dt-bindings: firmware: scm: Add compatible for SDX75
soc: qcom: mdt_loader: Fix split image detection
dt-bindings: memory-controllers: drop unneeded quotes
soc: rockchip: dtpm: use C99 array init syntax
firmware: tegra: bpmp: Add support for DRAM MRQ GSCs
soc/tegra: pmc: Use devm_clk_notifier_register()
soc/tegra: pmc: Simplify debugfs initialization
...
Merge series from Biju Das <biju.das.jz@bp.renesas.com>:
This patch series aims to add support for Renesas PMIC RAA215300 and
built-in RTC found on this PMIC device.
The details of PMIC can be found here[1].
Renesas PMIC RAA215300 exposes two separate i2c devices, one for the main
device and another for rtc device.
rk3588-based "General-register-files" register areas and a move to
C99 array inits for the dtpm driver to fix sparse warnings.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAmSGMvYQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVtnB/9Mm4ppU1GRJiK8TSZIVFfM5YZRoNyGgRXF
oGtF8LvMq7/v0Ep1G+NgvbwdwCpzlIM0Z9Uo/3AfVqft9rFN8TpKbYDLRGryuIbC
L+8kqk4pmBo/U6ZApwylUcBGNymyliHdsOYqMqbWqRvwK2tXbgMlO6c3Yna0VXD7
l8fvn9/jtHBQwVniF9iIGbQbAS+avJcyCamh8Wn/Hs5Ke60NRNUhLuvHs4mom82R
26IuO9QkkRQCU/hC22NydPnBmK7dSQMqiInI9XgoMYOZi9TJ8+OrTExc0kkUZVAL
i4Vg+XGmDXmTtAd11C6NjsLhMuzhsR1znk3ndQjsjUnw0QlhNSHP
=rrNf
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=R3D1
-----END PGP SIGNATURE-----
Merge tag 'v6.5-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/drivers
An addition to the rk3588 power-domains, some new syscon compatibles for
rk3588-based "General-register-files" register areas and a move to
C99 array inits for the dtpm driver to fix sparse warnings.
* tag 'v6.5-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: dtpm: use C99 array init syntax
dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon
dt-bindings: soc: rockchip: add rk3588 usb2phy syscon
soc: rockchip: power-domain: add rk3588 mem module support
Link: https://lore.kernel.org/r/10286366.nUPlyArG6x@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
