commit 08ce9a1b72 upstream.
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58ac1b3799 upstream.
Since there is no guarantee that the memory returned by
dma_alloc_coherent() is associated with a 'struct page', using the
architecture specific phys_to_page() is wrong, but using
virt_to_page() would be as well.
Stop using sg lists altogether and just use the *_single() functions
instead. This also simplifies the code a bit since the scatterlists in
this driver always have only one entry anyway.
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
gc: Add a commit log from the initial thread:
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
Fixes: cb06ff102e ("ARM: PL011: Add support for Rx DMA buffer polling.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231122171503.235649-1-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0b9d97a77 upstream.
The console is immediately assigned to the ma35d1 port without
checking its index. This oversight can lead to out-of-bounds
errors when the index falls outside the valid '0' to
MA35_UART_NR range. Such scenario trigges ran error like the
following:
UBSAN: array-index-out-of-bounds in drivers/tty/serial/ma35d1_serial.c:555:51
index -1 is out of range for type 'uart_ma35d1_port [17]
Check the index before using it and bail out with a warning.
Fixes: 930cbf92db ("tty: serial: Add Nuvoton ma35d1 serial driver support")
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Cc: Jacky Huang <ychuang3@nuvoton.com>
Cc: <stable@vger.kernel.org> # v6.5+
Link: https://lore.kernel.org/r/20231204163804.1331415-2-andi.shyti@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the 6.6.3 stable release
* tag 'v6.6.3': (526 commits)
Linux 6.6.3
drm/amd/display: Change the DMCUB mailbox memory location from FB to inbox
drm/amd/display: Clear dpcd_sink_ext_caps if not set
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
drivers/usb/dwc3/core.c
This is the 6.6.2 stable release
* tag 'v6.6.2': (634 commits)
Linux 6.6.2
btrfs: make found_logical_ret parameter mandatory for function queue_scrub_stripe()
btrfs: use u64 for buffer sizes in the tree search ioctls
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
drivers/clk/imx/clk-imx8mq.c
drivers/clk/imx/clk-imx8qxp.c
drivers/media/i2c/ov5640.c
drivers/misc/pci_endpoint_test.c
commit ef5dd8ec88 upstream.
The xencons_connect_backend() function allocates a local interdomain
event channel with xenbus_alloc_evtchn(), then calls
bind_interdomain_evtchn_to_irq_lateeoi() to bind to that port# on the
*remote* domain.
That doesn't work very well:
(qemu) device_add xen-console,id=con1,chardev=pty0
[ 44.323872] xenconsole console-1: 2 xenbus_dev_probe on device/console/1
[ 44.323995] xenconsole: probe of console-1 failed with error -2
Fix it to use bind_evtchn_to_irq_lateeoi(), which does the right thing
by just binding that *local* event channel to an irq. The backend will
do the interdomain binding.
This didn't affect the primary console because the setup for that is
special — the toolstack allocates the guest event channel and the guest
discovers it with HVMOP_get_param.
Fixes: fe415186b4 ("xen/console: harden hvc_xen against event channel storms")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-2-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2704c9a559 upstream.
The xen_hvc_init() function should always register the frontend driver,
even when there's no primary console — as there may be secondary consoles.
(Qemu can always add secondary consoles, but only the toolstack can add
the primary because it's special.)
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-3-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30badfd7c upstream.
On unplug of a Xen console, xencons_disconnect_backend() unconditionally
calls free_irq() via unbind_from_irqhandler(), causing a warning of
freeing an already-free IRQ:
(qemu) device_del con1
[ 32.050919] ------------[ cut here ]------------
[ 32.050942] Trying to free already-free IRQ 33
[ 32.050990] WARNING: CPU: 0 PID: 51 at kernel/irq/manage.c:1895 __free_irq+0x1d4/0x330
It should be using evtchn_put() to tear down the event channel binding,
and let the Linux IRQ side of it be handled by notifier_del_irq() through
the HVC code.
On which topic... xencons_disconnect_backend() should call hvc_remove()
*first*, rather than tearing down the event channel and grant mapping
while they are in use. And then the IRQ is guaranteed to be freed by
the time it's torn down by evtchn_put().
Since evtchn_put() also closes the actual event channel, avoid calling
xenbus_free_evtchn() except in the failure path where the IRQ was not
successfully set up.
However, calling hvc_remove() at the start of xencons_disconnect_backend()
still isn't early enough. An unplug request is indicated by the backend
setting its state to XenbusStateClosing, which triggers a notification
to xencons_backend_changed(), which... does nothing except set its own
frontend state directly to XenbusStateClosed without *actually* tearing
down the HVC device or, you know, making sure it isn't actively in use.
So the backend sees the guest frontend set its state to XenbusStateClosed
and stops servicing the interrupt... and the guest spins for ever in the
domU_write_console() function waiting for the ring to drain.
Fix that one by calling hvc_remove() from xencons_backend_changed() before
signalling to the backend that it's OK to proceed with the removal.
Tested with 'dd if=/dev/zero of=/dev/hvc1' while telling Qemu to remove
the console device.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-4-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd976a97d1 upstream.
The smp_processor_id() shouldn't be called from preemptible code.
Instead use get_cpu() and put_cpu() which disables preemption in
addition to getting the processor id. Enable preemption back after
calling schedule_work() to make sure that the work gets scheduled on all
cores other than the current core. We want to avoid a scenario where
current core's stack trace is printed multiple times and one core's
stack trace isn't printed because of scheduling of current task.
This fixes the following bug:
[ 119.143590] sysrq: Show backtrace of all active CPUs
[ 119.143902] BUG: using smp_processor_id() in preemptible [00000000] code: bash/873
[ 119.144586] caller is debug_smp_processor_id+0x20/0x30
[ 119.144827] CPU: 6 PID: 873 Comm: bash Not tainted 5.10.124-dirty #3
[ 119.144861] Hardware name: QEMU QEMU Virtual Machine, BIOS 2023.05-1 07/22/2023
[ 119.145053] Call trace:
[ 119.145093] dump_backtrace+0x0/0x1a0
[ 119.145122] show_stack+0x18/0x70
[ 119.145141] dump_stack+0xc4/0x11c
[ 119.145159] check_preemption_disabled+0x100/0x110
[ 119.145175] debug_smp_processor_id+0x20/0x30
[ 119.145195] sysrq_handle_showallcpus+0x20/0xc0
[ 119.145211] __handle_sysrq+0x8c/0x1a0
[ 119.145227] write_sysrq_trigger+0x94/0x12c
[ 119.145247] proc_reg_write+0xa8/0xe4
[ 119.145266] vfs_write+0xec/0x280
[ 119.145282] ksys_write+0x6c/0x100
[ 119.145298] __arm64_sys_write+0x20/0x30
[ 119.145315] el0_svc_common.constprop.0+0x78/0x1e4
[ 119.145332] do_el0_svc+0x24/0x8c
[ 119.145348] el0_svc+0x10/0x20
[ 119.145364] el0_sync_handler+0x134/0x140
[ 119.145381] el0_sync+0x180/0x1c0
Cc: jirislaby@kernel.org
Cc: stable@vger.kernel.org
Fixes: 47cab6a722 ("debug lockups: Improve lockup detection, fix generic arch fallback")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20231009162021.3607632-1-usama.anjum@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d81ffb87aa ]
Add check for the return value of kstrdup() and return the error, if it
fails in order to avoid NULL pointer dereference.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230904035220.48164-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11e7f27b79 ]
There is a pid leakage:
------------------------------
unreferenced object 0xffff88810c181940 (size 224):
comm "sshd", pid 8191, jiffies 4294946950 (age 524.570s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 ad 4e ad de .............N..
ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:
[<ffffffff814774e6>] kmem_cache_alloc+0x5c6/0x9b0
[<ffffffff81177342>] alloc_pid+0x72/0x570
[<ffffffff81140ac4>] copy_process+0x1374/0x2470
[<ffffffff81141d77>] kernel_clone+0xb7/0x900
[<ffffffff81142645>] __se_sys_clone+0x85/0xb0
[<ffffffff8114269b>] __x64_sys_clone+0x2b/0x30
[<ffffffff83965a72>] do_syscall_64+0x32/0x80
[<ffffffff83a00085>] entry_SYSCALL_64_after_hwframe+0x61/0xc6
It turns out that there is a race condition between disassociate_ctty() and
tty_signal_session_leader(), which caused this leakage.
The pid memleak is triggered by the following race:
task[sshd] task[bash]
----------------------- -----------------------
disassociate_ctty();
spin_lock_irq(¤t->sighand->siglock);
put_pid(current->signal->tty_old_pgrp);
current->signal->tty_old_pgrp = NULL;
tty = tty_kref_get(current->signal->tty);
spin_unlock_irq(¤t->sighand->siglock);
tty_vhangup();
tty_lock(tty);
...
tty_signal_session_leader();
spin_lock_irq(&p->sighand->siglock);
...
if (tty->ctrl.pgrp) //tty->ctrl.pgrp is not NULL
p->signal->tty_old_pgrp = get_pid(tty->ctrl.pgrp); //An extra get
spin_unlock_irq(&p->sighand->siglock);
...
tty_unlock(tty);
if (tty) {
tty_lock(tty);
...
put_pid(tty->ctrl.pgrp);
tty->ctrl.pgrp = NULL; //It's too late
...
tty_unlock(tty);
}
The issue is believed to be introduced by commit c8bcd9c5be ("tty:
Fix ->session locking") who moves the unlock of siglock in
disassociate_ctty() above "if (tty)", making a small window allowing
tty_signal_session_leader() to kick in. It can be easily reproduced by
adding a delay before "if (tty)" and at the entrance of
tty_signal_session_leader().
To fix this issue, we move "put_pid(current->signal->tty_old_pgrp)" after
"tty->ctrl.pgrp = NULL".
Fixes: c8bcd9c5be ("tty: Fix ->session locking")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Co-developed-by: GUO Zihua <guozihua@huawei.com>
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Link: https://lore.kernel.org/r/20230831023329.165737-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f699743ae upstream.
Richard reported that a serial port may end up sometimes with tx data
pending in the buffer for long periods of time.
Turns out we bail out early on any errors from pm_runtime_get(),
including -EINPROGRESS. To fix the issue, we need to ignore -EINPROGRESS
as we only care about the runtime PM usage count at this point. We check
for an active runtime PM state later on for tx.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Bruce Ashfield <bruce.ashfield@gmail.com>
Cc: Mikko Rapeli <mikko.rapeli@linaro.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Randy MacLeod <randy.macleod@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231023074856.61896-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4876dacac upstream.
Some of the later revisions of the Brainboxes PX cards are based
on the Oxford Semiconductor chipset. Due to the chip's unique setup
these cards need to be initialised.
Previously these were tested against a reference card with the same broken
baudrate on another PC, cancelling out the effect. With this patch they
work and can transfer/receive find against an FTDI-based device.
Add all of the cards which require this setup to the quirks table.
Thanks to Maciej W. Rozycki for clarification on this chip.
Fixes: ef5a03a26c ("tty: 8250: Add support for Brainboxes PX cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB7899D222A4AB2A4E8C57108FC4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33092fb3af upstream.
The UC-257 is a serial + LPT card, so remove it from this driver.
A patch has been submitted to add it to parport_serial instead.
Additionaly, the UC-431 does not use this card ID, only the UC-420
does. The 431 is a 3-port card and there is no generic 3-port configuration
available, so remove reference to it from this driver.
Fixes: 152d1afa83 ("tty: Add support for Brainboxes UC cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB78995ADF7394C74AD4CF3357C4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a75b205de upstream.
gsm_cleanup_mux() cleans up the gsm by closing all DLCIs, stopping all
timers, removing the virtual tty devices and clearing the data queues.
This procedure, however, may cause subsequent changes of the virtual modem
status lines of a DLCI. More data is being added the outgoing data queue
and the deleted kick timer is restarted to handle this. At this point many
resources have already been removed by the cleanup procedure. Thus, a
kernel panic occurs.
Fix this by proving in gsm_modem_update() that the cleanup procedure has
not been started and the mux is still alive.
Note that writing to a virtual tty is already protected by checks against
the DLCI specific connection state.
Fixes: c568f7086c ("tty: n_gsm: fix missing timer to handle stalled links")
Cc: stable <stable@kernel.org>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20231026055844.3127-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since sdma hardware configure postpone to transfer phase, have to disable
dma request on uart driver before dma transfer setup because there is
a hardware limitation on sdma event enable(ENBLn) as below (event enabled
in imx_uart_dma_init() before where's ahead of dma request enable):
"It is thus essential for the Arm platform to program them before any DMA
request is triggered to the SDMA, otherwise an unpredictable combination
of channels may be started."
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Add busfreq and pm qos support for DMA mode.
DMA mode cannot work stablely at low busfreq mode, so request
high busfreq once DMA is enabled.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Maximilian reported that surface_serial_hub serdev tx does not work during
system suspend. During system suspend, runtime PM gets disabled in
__device_suspend_late(), and tx is unable to wake-up the serial core port
device that we use to check if tx is safe to start. Johan summarized the
regression noting that serdev tx no longer always works as earlier when the
serdev device is runtime PM active.
The serdev device and the serial core controller devices are siblings of
the serial port hardware device. The runtime PM usage count from serdev
device does not propagate to the serial core device siblings, it only
propagates to the parent.
In addition to the tx issue for suspend, testing for the serial core port
device can cause an unnecessary delay in enabling tx while waiting for the
serial core port device to wake-up. The serial core port device wake-up is
only needed to flush pending tx when the serial port hardware device was
in runtime PM suspended state.
To fix the regression, we need to check the runtime PM state of the parent
serial port hardware device for tx instead of the serial core port device.
As the serial port device drivers may or may not implement runtime PM, we
need to also add a check for pm_runtime_enabled().
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@kernel.org>
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231005075644.25936-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a6261 ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a6261 ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 44b27aec9d ("serial: core, 8250: set RS485 termination GPIO in
serial core") enabled support for RS485 termination GPIOs behind i2c
expanders by setting the GPIO outside of the critical section protected
by the port spinlock. Access to the i2c expander may sleep, which
caused a splat with the port spinlock held.
Commit 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in
driver-specific way") erroneously regressed that by spinlocking the
GPIO manipulation again.
Fix by moving uart_rs485_config() (the function manipulating the GPIO)
outside of the spinlocked section and acquiring the spinlock inside of
uart_rs485_config() for the invocation of ->rs485_config() only.
This gets us one step closer to pushing the spinlock down into the
->rs485_config() callbacks which actually need it. (Some callbacks
do not want to be spinlocked because they perform sleepable register
accesses, see e.g. sc16is7xx_config_rs485().)
Stack trace for posterity:
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 56 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch
Call trace:
rcu_note_context_switch
__schedule
schedule
schedule_timeout
wait_for_completion_timeout
bcm2835_i2c_xfer
__i2c_transfer
i2c_transfer
i2c_transfer_buffer_flags
regmap_i2c_write
_regmap_raw_write_impl
_regmap_bus_raw_write
_regmap_write
_regmap_update_bits
regmap_update_bits_base
pca953x_gpio_set_value
gpiod_set_raw_value_commit
gpiod_set_value_nocheck
gpiod_set_value_cansleep
uart_rs485_config
uart_add_one_port
pl011_register_port
pl011_probe
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.1+
Link: https://lore.kernel.org/r/f3a35967c28b32f3c6432d0aa5936e6a9908282d.1695307688.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9b9c8195f3.
The commit above is reverted as it did not solve the original issue.
gsm_cleanup_mux() tries to free up the virtual ttys by calling
gsm_dlci_release() for each available DLCI. There, dlci_put() is called to
decrease the reference counter for the DLCI via tty_port_put() which
finally calls gsm_dlci_free(). This already clears the pointer which is
being checked in gsm_cleanup_mux() before calling gsm_dlci_release().
Therefore, it is not necessary to clear this pointer in gsm_cleanup_mux()
as done in the reverted commit. The commit introduces a null pointer
dereference:
<TASK>
? __die+0x1f/0x70
? page_fault_oops+0x156/0x420
? search_exception_tables+0x37/0x50
? fixup_exception+0x21/0x310
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? tty_port_put+0x19/0xa0
gsmtty_cleanup+0x29/0x80 [n_gsm]
release_one_tty+0x37/0xe0
process_one_work+0x1e6/0x3e0
worker_thread+0x4c/0x3d0
? __pfx_worker_thread+0x10/0x10
kthread+0xe1/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2f/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The actual issue is that nothing guards dlci_put() from being called
multiple times while the tty driver was triggered but did not yet finished
calling gsm_dlci_free().
Fixes: 9b9c8195f3 ("tty: n_gsm: fix UAF in gsm_cleanup_mux")
Cc: stable <stable@kernel.org>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230914051507.3240-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
Fixes: 0ba9e3a13c ("serial: 8250: Add missing wakeup event reporting")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230831222555.614426-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
("refactor Kconfig to consolidate KEXEC and CRASH options").
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h").
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands").
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions").
- Switch the handling of kdump from a udev scheme to in-kernel handling,
by Eric DeVolder ("crash: Kernel handling of CPU and memory hot
un/plug").
- Many singleton patches to various parts of the tree
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZO2GpAAKCRDdBJ7gKXxA
juW3AQD1moHzlSN6x9I3tjm5TWWNYFoFL8af7wXDJspp/DWH/AD/TO0XlWWhhbYy
QHy7lL0Syha38kKLMXTM+bN6YQHi9AU=
=WJQa
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- An extensive rework of kexec and crash Kconfig from Eric DeVolder
("refactor Kconfig to consolidate KEXEC and CRASH options")
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h")
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands")
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions")
- Switch the handling of kdump from a udev scheme to in-kernel
handling, by Eric DeVolder ("crash: Kernel handling of CPU and memory
hot un/plug")
- Many singleton patches to various parts of the tree
* tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (81 commits)
document while_each_thread(), change first_tid() to use for_each_thread()
drivers/char/mem.c: shrink character device's devlist[] array
x86/crash: optimize CPU changes
crash: change crash_prepare_elf64_headers() to for_each_possible_cpu()
crash: hotplug support for kexec_load()
x86/crash: add x86 crash hotplug support
crash: memory and CPU hotplug sysfs attributes
kexec: exclude elfcorehdr from the segment digest
crash: add generic infrastructure for crash hotplug support
crash: move a few code bits to setup support of crash hotplug
kstrtox: consistently use _tolower()
kill do_each_thread()
nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
scripts/bloat-o-meter: count weak symbol sizes
treewide: drop CONFIG_EMBEDDED
lockdep: fix static memory detection even more
lib/vsprintf: declare no_hash_pointers in sprintf.h
lib/vsprintf: split out sprintf() and friends
kernel/fork: stop playing lockless games for exe_file replacement
adfs: delete unused "union adfs_dirtail" definition
...
- Peter Xu has a series (mm/gup: Unify hugetlb, speed up thp") which
reduces the special-case code for handling hugetlb pages in GUP. It
also speeds up GUP handling of transparent hugepages.
- Peng Zhang provides some maple tree speedups ("Optimize the fast path
of mas_store()").
- Sergey Senozhatsky has improved te performance of zsmalloc during
compaction (zsmalloc: small compaction improvements").
- Domenico Cerasuolo has developed additional selftest code for zswap
("selftests: cgroup: add zswap test program").
- xu xin has doe some work on KSM's handling of zero pages. These
changes are mainly to enable the user to better understand the
effectiveness of KSM's treatment of zero pages ("ksm: support tracking
KSM-placed zero-pages").
- Jeff Xu has fixes the behaviour of memfd's
MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED sysctl ("mm/memfd: fix sysctl
MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED").
- David Howells has fixed an fscache optimization ("mm, netfs, fscache:
Stop read optimisation when folio removed from pagecache").
- Axel Rasmussen has given userfaultfd the ability to simulate memory
poisoning ("add UFFDIO_POISON to simulate memory poisoning with UFFD").
- Miaohe Lin has contributed some routine maintenance work on the
memory-failure code ("mm: memory-failure: remove unneeded PageHuge()
check").
- Peng Zhang has contributed some maintenance work on the maple tree
code ("Improve the validation for maple tree and some cleanup").
- Hugh Dickins has optimized the collapsing of shmem or file pages into
THPs ("mm: free retracted page table by RCU").
- Jiaqi Yan has a patch series which permits us to use the healthy
subpages within a hardware poisoned huge page for general purposes
("Improve hugetlbfs read on HWPOISON hugepages").
- Kemeng Shi has done some maintenance work on the pagetable-check code
("Remove unused parameters in page_table_check").
- More folioification work from Matthew Wilcox ("More filesystem folio
conversions for 6.6"), ("Followup folio conversions for zswap"). And
from ZhangPeng ("Convert several functions in page_io.c to use a
folio").
- page_ext cleanups from Kemeng Shi ("minor cleanups for page_ext").
- Baoquan He has converted some architectures to use the GENERIC_IOREMAP
ioremap()/iounmap() code ("mm: ioremap: Convert architectures to take
GENERIC_IOREMAP way").
- Anshuman Khandual has optimized arm64 tlb shootdown ("arm64: support
batched/deferred tlb shootdown during page reclamation/migration").
- Better maple tree lockdep checking from Liam Howlett ("More strict
maple tree lockdep"). Liam also developed some efficiency improvements
("Reduce preallocations for maple tree").
- Cleanup and optimization to the secondary IOMMU TLB invalidation, from
Alistair Popple ("Invalidate secondary IOMMU TLB on permission
upgrade").
- Ryan Roberts fixes some arm64 MM selftest issues ("selftests/mm fixes
for arm64").
- Kemeng Shi provides some maintenance work on the compaction code ("Two
minor cleanups for compaction").
- Some reduction in mmap_lock pressure from Matthew Wilcox ("Handle most
file-backed faults under the VMA lock").
- Aneesh Kumar contributes code to use the vmemmap optimization for DAX
on ppc64, under some circumstances ("Add support for DAX vmemmap
optimization for ppc64").
- page-ext cleanups from Kemeng Shi ("add page_ext_data to get client
data in page_ext"), ("minor cleanups to page_ext header").
- Some zswap cleanups from Johannes Weiner ("mm: zswap: three
cleanups").
- kmsan cleanups from ZhangPeng ("minor cleanups for kmsan").
- VMA handling cleanups from Kefeng Wang ("mm: convert to
vma_is_initial_heap/stack()").
- DAMON feature work from SeongJae Park ("mm/damon/sysfs-schemes:
implement DAMOS tried total bytes file"), ("Extend DAMOS filters for
address ranges and DAMON monitoring targets").
- Compaction work from Kemeng Shi ("Fixes and cleanups to compaction").
- Liam Howlett has improved the maple tree node replacement code
("maple_tree: Change replacement strategy").
- ZhangPeng has a general code cleanup - use the K() macro more widely
("cleanup with helper macro K()").
- Aneesh Kumar brings memmap-on-memory to ppc64 ("Add support for memmap
on memory feature on ppc64").
- pagealloc cleanups from Kemeng Shi ("Two minor cleanups for pcp list
in page_alloc"), ("Two minor cleanups for get pageblock migratetype").
- Vishal Moola introduces a memory descriptor for page table tracking,
"struct ptdesc" ("Split ptdesc from struct page").
- memfd selftest maintenance work from Aleksa Sarai ("memfd: cleanups
for vm.memfd_noexec").
- MM include file rationalization from Hugh Dickins ("arch: include
asm/cacheflush.h in asm/hugetlb.h").
- THP debug output fixes from Hugh Dickins ("mm,thp: fix sloppy text
output").
- kmemleak improvements from Xiaolei Wang ("mm/kmemleak: use
object_cache instead of kmemleak_initialized").
- More folio-related cleanups from Matthew Wilcox ("Remove _folio_dtor
and _folio_order").
- A VMA locking scalability improvement from Suren Baghdasaryan
("Per-VMA lock support for swap and userfaults").
- pagetable handling cleanups from Matthew Wilcox ("New page table range
API").
- A batch of swap/thp cleanups from David Hildenbrand ("mm/swap: stop
using page->private on tail pages for THP_SWAP + cleanups").
- Cleanups and speedups to the hugetlb fault handling from Matthew
Wilcox ("Change calling convention for ->huge_fault").
- Matthew Wilcox has also done some maintenance work on the MM subsystem
documentation ("Improve mm documentation").
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZO1JUQAKCRDdBJ7gKXxA
jrMwAP47r/fS8vAVT3zp/7fXmxaJYTK27CTAM881Gw1SDhFM/wEAv8o84mDenCg6
Nfio7afS1ncD+hPYT8947UnLxTgn+ww=
=Afws
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-08-28-18-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Some swap cleanups from Ma Wupeng ("fix WARN_ON in
add_to_avail_list")
- Peter Xu has a series (mm/gup: Unify hugetlb, speed up thp") which
reduces the special-case code for handling hugetlb pages in GUP. It
also speeds up GUP handling of transparent hugepages.
- Peng Zhang provides some maple tree speedups ("Optimize the fast path
of mas_store()").
- Sergey Senozhatsky has improved te performance of zsmalloc during
compaction (zsmalloc: small compaction improvements").
- Domenico Cerasuolo has developed additional selftest code for zswap
("selftests: cgroup: add zswap test program").
- xu xin has doe some work on KSM's handling of zero pages. These
changes are mainly to enable the user to better understand the
effectiveness of KSM's treatment of zero pages ("ksm: support
tracking KSM-placed zero-pages").
- Jeff Xu has fixes the behaviour of memfd's
MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED sysctl ("mm/memfd: fix sysctl
MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED").
- David Howells has fixed an fscache optimization ("mm, netfs, fscache:
Stop read optimisation when folio removed from pagecache").
- Axel Rasmussen has given userfaultfd the ability to simulate memory
poisoning ("add UFFDIO_POISON to simulate memory poisoning with
UFFD").
- Miaohe Lin has contributed some routine maintenance work on the
memory-failure code ("mm: memory-failure: remove unneeded PageHuge()
check").
- Peng Zhang has contributed some maintenance work on the maple tree
code ("Improve the validation for maple tree and some cleanup").
- Hugh Dickins has optimized the collapsing of shmem or file pages into
THPs ("mm: free retracted page table by RCU").
- Jiaqi Yan has a patch series which permits us to use the healthy
subpages within a hardware poisoned huge page for general purposes
("Improve hugetlbfs read on HWPOISON hugepages").
- Kemeng Shi has done some maintenance work on the pagetable-check code
("Remove unused parameters in page_table_check").
- More folioification work from Matthew Wilcox ("More filesystem folio
conversions for 6.6"), ("Followup folio conversions for zswap"). And
from ZhangPeng ("Convert several functions in page_io.c to use a
folio").
- page_ext cleanups from Kemeng Shi ("minor cleanups for page_ext").
- Baoquan He has converted some architectures to use the
GENERIC_IOREMAP ioremap()/iounmap() code ("mm: ioremap: Convert
architectures to take GENERIC_IOREMAP way").
- Anshuman Khandual has optimized arm64 tlb shootdown ("arm64: support
batched/deferred tlb shootdown during page reclamation/migration").
- Better maple tree lockdep checking from Liam Howlett ("More strict
maple tree lockdep"). Liam also developed some efficiency
improvements ("Reduce preallocations for maple tree").
- Cleanup and optimization to the secondary IOMMU TLB invalidation,
from Alistair Popple ("Invalidate secondary IOMMU TLB on permission
upgrade").
- Ryan Roberts fixes some arm64 MM selftest issues ("selftests/mm fixes
for arm64").
- Kemeng Shi provides some maintenance work on the compaction code
("Two minor cleanups for compaction").
- Some reduction in mmap_lock pressure from Matthew Wilcox ("Handle
most file-backed faults under the VMA lock").
- Aneesh Kumar contributes code to use the vmemmap optimization for DAX
on ppc64, under some circumstances ("Add support for DAX vmemmap
optimization for ppc64").
- page-ext cleanups from Kemeng Shi ("add page_ext_data to get client
data in page_ext"), ("minor cleanups to page_ext header").
- Some zswap cleanups from Johannes Weiner ("mm: zswap: three
cleanups").
- kmsan cleanups from ZhangPeng ("minor cleanups for kmsan").
- VMA handling cleanups from Kefeng Wang ("mm: convert to
vma_is_initial_heap/stack()").
- DAMON feature work from SeongJae Park ("mm/damon/sysfs-schemes:
implement DAMOS tried total bytes file"), ("Extend DAMOS filters for
address ranges and DAMON monitoring targets").
- Compaction work from Kemeng Shi ("Fixes and cleanups to compaction").
- Liam Howlett has improved the maple tree node replacement code
("maple_tree: Change replacement strategy").
- ZhangPeng has a general code cleanup - use the K() macro more widely
("cleanup with helper macro K()").
- Aneesh Kumar brings memmap-on-memory to ppc64 ("Add support for
memmap on memory feature on ppc64").
- pagealloc cleanups from Kemeng Shi ("Two minor cleanups for pcp list
in page_alloc"), ("Two minor cleanups for get pageblock
migratetype").
- Vishal Moola introduces a memory descriptor for page table tracking,
"struct ptdesc" ("Split ptdesc from struct page").
- memfd selftest maintenance work from Aleksa Sarai ("memfd: cleanups
for vm.memfd_noexec").
- MM include file rationalization from Hugh Dickins ("arch: include
asm/cacheflush.h in asm/hugetlb.h").
- THP debug output fixes from Hugh Dickins ("mm,thp: fix sloppy text
output").
- kmemleak improvements from Xiaolei Wang ("mm/kmemleak: use
object_cache instead of kmemleak_initialized").
- More folio-related cleanups from Matthew Wilcox ("Remove _folio_dtor
and _folio_order").
- A VMA locking scalability improvement from Suren Baghdasaryan
("Per-VMA lock support for swap and userfaults").
- pagetable handling cleanups from Matthew Wilcox ("New page table
range API").
- A batch of swap/thp cleanups from David Hildenbrand ("mm/swap: stop
using page->private on tail pages for THP_SWAP + cleanups").
- Cleanups and speedups to the hugetlb fault handling from Matthew
Wilcox ("Change calling convention for ->huge_fault").
- Matthew Wilcox has also done some maintenance work on the MM
subsystem documentation ("Improve mm documentation").
* tag 'mm-stable-2023-08-28-18-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (489 commits)
maple_tree: shrink struct maple_tree
maple_tree: clean up mas_wr_append()
secretmem: convert page_is_secretmem() to folio_is_secretmem()
nios2: fix flush_dcache_page() for usage from irq context
hugetlb: add documentation for vma_kernel_pagesize()
mm: add orphaned kernel-doc to the rst files.
mm: fix clean_record_shared_mapping_range kernel-doc
mm: fix get_mctgt_type() kernel-doc
mm: fix kernel-doc warning from tlb_flush_rmaps()
mm: remove enum page_entry_size
mm: allow ->huge_fault() to be called without the mmap_lock held
mm: move PMD_ORDER to pgtable.h
mm: remove checks for pte_index
memcg: remove duplication detection for mem_cgroup_uncharge_swap
mm/huge_memory: work on folio->swap instead of page->private when splitting folio
mm/swap: inline folio_set_swap_entry() and folio_swap_entry()
mm/swap: use dedicated entry for swap in folio
mm/swap: stop using page->private on tail pages for THP_SWAP
selftests/mm: fix WARNING comparing pointer to 0
selftests: cgroup: fix test_kmem_memcg_deletion kernel mem check
...
The code is duplicated to perform the copy twice -- to handle buffer
wrap-around. Instead of the duplication, roll this into the loop.
(And add some blank lines around to have the code a bit more readable.)
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__process_echoes() contains ECHO_OPs processing. It is stuffed in a
while loop and the whole function is barely readable. Separate it to a
new function: n_tty_process_echo_ops().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some count types are already 'size_t' for a long time. Some were
switched to 'size_t' recently. Unify the rest with those now.
This allows for some min_t()s to become min()s. And make one min()
an explicit min_t() as we are comparing signed 'room' to unsigned
'count'.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'if' in chars_in_buffer() is misleadingly inverted. And since the
only difference is the head used for computation, cache the head using
ternary operator. And use that in return directly.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We compile with -funsigned-char, so all character constants are already
unsigned chars. Therefore, remove superfluous casts.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, n_tty handles the newline in a label in
n_tty_receive_char_canon(). That is invoked from two more places. Split
this code to a separate function and avoid the label in this case.
This makes the code flow more understandable.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_tty_receive_char_special() is already complicated enough. Split the
canon handling to a separate function: n_tty_receive_char_canon().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In n_tty, there is already a macro to mask out top bits from ring buffer
counters. It is MASK() added some time ago. So use it more in the code
to make it more readable.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_tty_data::num_overrun is unlikely to overflow in a second. But make it
explicitly unsigned to avoid printing negative values.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The jiffies tests in n_tty_receive_overrun() are simplified ratelimiting
(without locking). We could use struct ratelimit_state and the helpers,
but to me, it occurs to be too complex for this use case.
But the code currently tests both if the time passed (the first
time_after()) and if jiffies wrapped around (the second time_after()).
time_is_before_jiffies() takes care of both, provided overrun_time is
initialized at the allocation time.
So switch to time_is_before_jiffies(), the same what ratelimiting does.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a separate misnomer 'c' to hold the retuned value from
tty->ops->write(). Instead, use 'num' already defined on another place
(and already properly typed).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point to use a local variable to store the character when we
can pass it directly. This assignment comes from era when we used to do
get_user(c, b). We no longer need this, so fix this.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'flow' parameter of n_tty_receive_buf_common() is meant to be a
boolean value. So use bool and alter call sites accordingly.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230827074147.2287-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6a4197f976
New SoC will use ttyS0 instead of ttyAML, so T7 SoC doesn't need a
OF_EARLYCON_DECLARE.
Fixes: 6a4197f976 ("tty: serial: meson: Add a earlycon for the T7 SoC")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Link: https://lore.kernel.org/r/20230827082944.5100-1-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 BCM7271 UART is not a direct match to PORT_16550A and other
generic ports do not match its hardware capabilities. PORT_ALTR matches
the rx trigger levels, but its vendor configurations are not compatible.
Unfortunately this means we need to create another port to fully capture
the hardware capabilities of the BCM7271 UART.
To alleviate some latency pressures, we default the rx trigger level to 8.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/1692643978-16570-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve rs485 devicetree properties on registration of sc16is7xx ports in
case they are attached to an rs485 transceiver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
and commit 21144bab4f ("sc16is7xx: Handle modem status lines")
changed the function of the GPIOs pins to act as modem control
lines without any possibility of selecting GPIO function.
As a consequence, applications that depends on GPIO lines configured
by default as GPIO pins no longer work as expected.
Also, the change to select modem control lines function was done only
for channel A of dual UART variants (752/762). This was not documented
in the log message.
Allow to specify GPIO or modem control line function in the device
tree, and for each of the ports (A or B).
Do so by using the new device-tree property named
"nxp,modem-control-line-ports" (property added in separate patch).
When registering GPIO chip controller, mask-out GPIO pins declared as
modem control lines according to this new DT property.
Fixes: 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
Fixes: 21144bab4f ("sc16is7xx: Handle modem status lines")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230807214556.540627-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c8f71b49ee ("serial: sc16is7xx: setup GPIO controller later
in probe") moved GPIO setup code later in probe function. Doing so
also required to move ports cleanup code (out_ports label) after the
GPIO cleanup code.
After these moves, the out_thread label becomes misplaced and makes
part of the cleanup code illogical.
This patch remove the now obsolete out_thread label and make GPIO
setup code jump to out_ports label if it fails.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230807214556.540627-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there's no irq(this can be due to various reasons, for example,
no irq from HW support, or we just want to use poll solution, and so
on), falling back to poll is still better than no support at all.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20230806092056.2467-3-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tegra_uart_hw_init(), the return value of clk_prepare_enable() should
be checked since it might fail.
Fixes: e9ea096dd2 ("serial: tegra: add serial driver")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20230817105406.228674-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the Sifive Uart is not used as the wake up source, suspend the uart
before the system enter the suspend state to prevent it woken up by
unexpected uart interrupt. Resume the uart once the system woken up.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20230815090216.2575971-1-nick.hu@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new Amlogic T7 SoC does not have a always-on uart,
so add OF_EARLYCON_DECLARE for it.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230814080128.143613-2-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In shutdown, RX DMA channel is terminated. If the DMA RX callback is
scheduled but not yet executed, while a new RX DMA transfer is started, the
callback can be executed, and then disturb the ongoing RX DMA transfer.
To avoid such a case, call dmaengine_synchronize in shutdown, after the
DMA RX channel is terminated.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-7-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
Create two new functions (stm32_usart_rx_dma_pause, stm32_usart_rx_dma
_resume) to handle dma error when pausing/resuming.
And rename stm32_usart_start_rx_dma_cyclic() to
stm32_usart_rx_dma_start_or_resume() and use this function to resume an
rx dma transfer. If resume fail, stm32_usart_rx_dma_start_or_resume can
create a new transfer to continue.
It is also safer to close DMA before reset DMAR in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-6-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create new function "stm32_usart_dma_pause_resume" that called dmaengine_
pause/resume and in case of error, terminate dma transaction.
Two other functions are created to facilitate the use of stm32_usart_dma
_pause_resume : stm32_usart_tx_dma_pause, stm32_usart_tx_dma_resume.
Equivalent functions for rx will be added in future patch.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename stm32_usart_rx_dma_enabled to stm32_usart_rx_dma_started in order
to match with stm32_usart_tx_dma_started.
Modify argument of stm32_usart_rx_dma_started from uart_port structure to
stm32_port structure to match with stm32_usart_tx_dma_started.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMAT is a configuration bit so it should be set at the startup of uart
port and not when a DMA transfer begins.
This patch move set of DMAT into set_termios and remove DMAT reset except
in shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
It is also safer to close DMA before reset DMAT in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, changing the parameters of the n_gsm mux gives no direct control
to the user whether this should trigger a mux reset or not. The decision is
solely made by the driver based on the assumption which parameter changes
are compatible or not. Therefore, the user has no means to perform an
automatic mux reset after parameter configuration for non-conflicting
changes.
Add the parameter 'flags' to 'gsm_config_ext' to force a mux reset after
ioctl setting regardless of whether the changes made require this or not
by setting this to 'GSM_FL_RESTART'. This is done similar to
'GSM_FL_RESTART' in gsm_dlci_config.flags.
Note that 'GSM_FL_RESTART' is currently the only allowed flag to allow
additions here.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple places in gsm_control_command and gsm_control_reply that
derive the specific DLCI handle directly out of the DLCI table in gsm.
Add a local variable which holds this handle and use it instead to improve
code readability.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The structure gsm_mux contains the 'unsupported' field. However, there is
currently no place in the code which increases this counter.
Increase the 'unsupported' statistics counter in the following case:
- an unsupported frame type has been requested by the peer via parameter
negotiation
- a control frame with an unsupported but known command has been received
Note that we have no means to detect an inconsistent/unsupported adaptation
sufficient accuracy as this changes the structure of the UI/UIH frames.
E.g. a one byte header is added in case of convergence layer type 2 instead
of 1 and contains the modem signal octet with the state of the signal
lines. There is no checksum or other value which indicates of this field is
correct or should be present. Therefore, we can only assume protocol
correctness here. See also 'gsm_dlci_data()' where this is handled.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The malformed counter in gsm_mux is already increased in case of errors
detected in gsm_queue() and gsm1_receive(). gsm_dlci_command() also
detects a case for a malformed frame but does not increase the malformed
counter yet.
Fix this by also increasing the gsm_mux malformed counter in case of a
malformed frame in gsm_dlci_command().
Note that the malformed counter is not yet exposed and only set internally.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the n_gsm link statistics by a failed link open counter in
preparation for an upcoming patch which will expose these.
This counter is increased whenever an attempt to open the control channel
failed. This is true in the following cases:
- new DLCI allocation failed
- connection request (SAMB) with invalid CR flag has been received
- connection response (UA) timed out
- parameter negotiation timed out or failed
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, changing the parameters of a DLCI gives no direct control to the
user whether this should trigger a channel reset or not. The decision is
solely made by the driver based on the assumption which parameter changes
are compatible or not. Therefore, the user has no means to perform an
automatic channel reset after parameter configuration for non-conflicting
changes.
Add the parameter 'flags' to 'gsm_dlci_config' to force a channel reset
after ioctl setting regardless of whether the changes made require this or
not by setting this to 'GSM_FL_RESTART'.
Note that 'GSM_FL_RESTART' is currently the only allow flag to allow
additions here.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230817093231.2317-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are used to handle "bad" states in the 'if's in the kernel. Refactor
(invert the two conditions in) __tty_buffer_request_room(), so that the
code returns from the fast paths immediately instead of postponing to
the heavy end of the function.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* use bool for 'change' as it holds a result of a boolean.
* use size_t for 'left', so it is the same as 'size' which it is
compared to. Both are supposed to contain an unsigned value.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use __tty_insert_flip_string_flags() for the slow path of
tty_insert_flip_char(). The former is generic enough, so there is no
reason to reimplement the injection once again.
So now we have a single function stuffing into tty buffers.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as in the previous patch, tty_prepare_flip_string() accepts
size_t as an size argument. It returns the same size (or less). It is
unexpected that it returns a signed value and can confuse users to check
for negative values.
Instead, return the same size_t as accepted to make clear we return
values >= 0, where zero in fact means failure.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the functions accept size_t as a size argument. They finally return
the same size (or less). It is quite unexpected that they return a
signed value and can confuse users to check for negative values.
Instead, return the same size_t as accepted to make clear we return
values >= 0, where zero in fact means failure.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And add a WARN_ON_ONCE(need_flags) to make sure we are not losing flags
in __tty_insert_flip_string_flags().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They both do the same except for flags. One mem-copies the flags from
the caller, the other mem-sets to one flag given by the caller. This can
be unified with a simple if in the unified function.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, that tty_buffer::data has the right type, use struct_size() for
size calculation. struct_size() makes the code less error-prone and more
readable.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric has pointed out that we still have 3 users of do_each_thread().
Change them to use for_each_process_thread() and kill this helper.
There is a subtle change, after do_each_thread/while_each_thread g == t ==
&init_task, while after for_each_process_thread() they both point to
nowhere, but this doesn't matter.
> Why is for_each_process_thread() better than do_each_thread()?
Say, for_each_process_thread() is rcu safe, do_each_thread() is not.
And certainly
for_each_process_thread(p, t) {
do_something(p, t);
}
looks better than
do_each_thread(p, t) {
do_something(p, t);
} while_each_thread(p, t);
And again, there are only 3 users of this awkward helper left. It should
have been killed years ago and in fact I thought it had already been
killed. It uses while_each_thread() which needs some changes.
Link: https://lkml.kernel.org/r/20230817163708.GA8248@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: "Christian Brauner (Microsoft)" <brauner@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jiri Slaby <jirislaby@kernel.org> # tty/serial
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
All callers of show_mem() pass 0 and NULL, so we can remove the two
arguments by directly calling __show_mem(0, NULL, MAX_NR_ZONES - 1) in
show_mem().
Link: https://lkml.kernel.org/r/20230630062253.189440-1-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We want to fix the serial core port DEVNAME to use a port id of the
hardware specific controller port instance instead of the port->line.
For example, the 8250 driver sets up a number of serial8250 ports
initially that can be inherited by the hardware specific driver. At that
the port->line no longer decribes the port's relation to the serial core
controller instance.
Let's fix the issue by assigning port->port_id for each serial core
controller port instance.
Fixes: 7d695d8376 ("serial: core: Fix serial_base_match() after fixing controller port name")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811103648.2826-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is not always held when calling serial8250_clear_IER().
When an oops is in progress, the lock is tried to be taken and when it
is not, a warning is issued:
WARNING: CPU: 0 PID: 1 at drivers/tty/serial/8250/8250_port.c:707 +0x57/0x60
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 6.5.0-rc5-1.g225bfb7-default+ #774 00f1be860db663ed29479b8255d3b01ab1135bd3
Hardware name: QEMU Standard PC ...
RIP: 0010:serial8250_clear_IER+0x57/0x60
...
Call Trace:
<TASK>
serial8250_console_write+0x9e/0x4b0
console_flush_all+0x217/0x5f0
...
Therefore, remove the annotation as it doesn't hold for all invocations.
The other option would be to make the lockdep test conditional on
'oops_in_progress' or pass 'locked' from serial8250_console_write(). I
don't think, that is worth it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Ogness <john.ogness@linutronix.de>
Fixes: d0b309a5d3 (serial: 8250: synchronize and annotate UART_IER access)
Link: https://lore.kernel.org/r/20230811064340.13400-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 9b9c8195f3 ("tty: n_gsm: fix UAF in gsm_cleanup_mux"), the UAF
problem is not completely fixed. There is a race condition in
gsm_cleanup_mux(), which caused this UAF.
The UAF problem is triggered by the following race:
task[5046] task[5054]
----------------------- -----------------------
gsm_cleanup_mux();
dlci = gsm->dlci[0];
mutex_lock(&gsm->mutex);
gsm_cleanup_mux();
dlci = gsm->dlci[0]; //Didn't take the lock
gsm_dlci_release(gsm->dlci[i]);
gsm->dlci[i] = NULL;
mutex_unlock(&gsm->mutex);
mutex_lock(&gsm->mutex);
dlci->dead = true; //UAF
Fix it by assigning values after mutex_lock().
Link: https://syzkaller.appspot.com/text?tag=CrashReport&x=176188b5a80000
Cc: stable <stable@kernel.org>
Fixes: 9b9c8195f3 ("tty: n_gsm: fix UAF in gsm_cleanup_mux")
Fixes: aa371e96f0 ("tty: n_gsm: fix restart handling via CLD command")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Co-developed-by: Qiumiao Zhang <zhangqiumiao1@huawei.com>
Signed-off-by: Qiumiao Zhang <zhangqiumiao1@huawei.com>
Link: https://lore.kernel.org/r/20230811031121.153237-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the type of tty_operations::write() counters with the 'count'
parameter. I.e. use size_t for them.
This includes changing vcc_port::chars_in_buffer to size_t to keep min()
and avoid min_t().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Link: https://lore.kernel.org/r/20230810091510.13006-34-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some hooks in struct tty_ldisc_ops still reference buffers by 'unsigned
char'. Unify to 'u8' as the rest of the tty layer does.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810091510.13006-32-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Somewhere, we use 'char', somewhere 'unsigned char'. Unify to 'u8' as
the rest of the tty layer does.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-31-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ld->ops->read() returns ssize_t. copy_to_iter() returns size_t. So
switch the variables ('size' and 'copied', respectively) to the
corresponding types.
This allows for use of min() in the next patch.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-26-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_read() is supposed to return ssize_t. It takes the return value from
iterate_tty_read(). That currently returns int. On the top of that,
iterate_tty_write() already returns ssize_t. So switch
iterate_tty_read() to ssize_t too, so that all three are consistent.
This means 'i' in tty_read() changes its type too. And while changing
that, rename this generic 'i' to more dedicated 'ret'.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-25-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It simplifies the code. The "price" is we have to unify 'chunk' to be
size_t the same as 'count' is. But that change is actually correct.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make do_tty_write()'s name sound similar to iterate_tty_read(). They
both do similar things, so there is no reason for so distinct names. The
new name is therefore iterate_tty_write().
Drop the unnedeed inline modifier too. Let the compiler decide.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-23-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
write() passed to do_tty_write() is always ld->ops->write(). Instead,
align with iterate_tty_read() and pass the whole ld instead. This makes
the code easier to follow as it is clear what the write is. And also the
function signature is more readable.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-22-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes all those 'char's an explicit 'u8'. This is part of the
continuing unification of chars and flags to be consistent u8.
This approaches tty_port_default_receive_buf().
Note that we do not change signedness as we compile with
-funsigned-char.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-18-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes all those 'unsigned char's an explicit 'u8'. This is part of
the continuing unification of chars and flags to be consistent u8.
This approaches tty_port_default_receive_buf(). Flags to be next.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-17-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Count passed to tty_ldisc_ops::receive_buf*(), ::lookahead_buf(), and
returned from ::receive_buf2() is expected to be size_t. So set it to
size_t to unify with the rest of the code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It comes from both paste_selection() and tty_port_default_receive_buf()
as unsigned (int and size_t respectively). Switch to size_t to converge
to that eventually.
Return the count as size_t too (the two callers above expect that).
Switch paste_selection()'s type of 'count' too, so that the returned and
passed type match.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'size_t' is what receive_buf() expects and returns while handling count.
So switch to 'size_t'.
This renders both local 'count' and 'rcvd' in flush_to_ldisc() to be
size_t too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The counts in tty_port_client_operations hooks' are currently
represented by all 'int', 'unsigned int', and 'size_t'. Unify them all
to unsigned 'size_t' for clarity. Note that size_t is used already in
tty_buffer.c. So, eventually, it is spread for counts everywhere and
this is the beginning.
So the two changes namely:
* ::receive_buf() is called from tty_ldisc_receive_buf(). And that
expects values ">= 0" from ::receive_buf(), so switch its rettype to
size_t is fine. tty_ldisc_receive_buf() types will be changed
separately.
* ::lookahead_buf()'s count comes from lookahead_bufs() and is already
'unsigned int'.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parameters are already unsigned chars. So make them explicitly u8s,
as the rest is going to be unified to u8 eventually too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* rename 'arg' to 'enable' as that is what it means.
* make 'bit' a tcflag_t, not int, as that is what cflags are.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a nop for everyone as TTY_DEBUG_WAIT_UNTIL_SENT is never set.
Provided, we have better debugging/printout mechanisms nowadays, remove
this mechanism.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line discipline variables are named 'ld' all over the tty code. Rename
these in tty_port, so that it is easier to grep for the code (namely for
"ld->ops").
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only tty_ldisc_ops::read() and ::write() of n_null behave differently than
the default ldops implementations. They return %EOPNOTSUPP instead of
%EIO. So keep only those two and remove the rest ldops as they are
superfluous.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX is handled by primary sequencer. After cancelling primary command, poll
primary sequencer's irq status instead of that of secondary.
While at it, also remove a couple of redundant lines that read from IRQ_EN
register and write back same.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1691578393-9891-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter reports boot issues with duplicate sysfs entries for multiport
drivers. Let's go back to using port->line for now to fix the regression.
With this change, the serial core port device names are not correct for the
hardware specific 8250 single port drivers, but that's a cosmetic issue for
now.
Fixes: d962de6ae5 ("serial: core: Fix serial core port id to not use port->line")
Reported-by: Guenter Roeck <groeck7@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230806062052.47737-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clarifies that the LEGACY_TIOCSTI setting is safe to turn off even
when running BRLTTY, as it was introduced in commit 690c8b804a
("TIOCSTI: always enable for CAP_SYS_ADMIN").
Signed-off-by: Günther Noack <gnoack3000@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20230808201115.23993-1-gnoack3000@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f0 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm().
Fixes: 04e82793f0 ("serial: 8250: Reinit port->pm on port specific driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804131553.52927-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After fixing the serial core port device to use port->port_id instead of
port->line, unloading a hardware specific 8250 port driver started
producing an error for "sysfs: cannot create duplicate filename".
This is happening as we are wrongly initializing port->port_id to zero
when adding back serial8250_isa_devs instances, and the serial8250:0.0
sysfs entry may already exist. For serial8250 devices, we typically have
multiple devices mapped to a single driver instance. For the
serial8250_isa_devs instances, the port->port_id is the same as port->line.
Let's fix the issue by re-initializing port_id when adding back the
serial8250_isa_devs instances in serial8250_unregister_port().
Fixes: d962de6ae5 ("serial: core: Fix serial core port id to not use port->line")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804123546.25293-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kmemleak reports issues for serial8250 ports after the hardware specific
driver takes over on boot as noted by Tomi.
The kerneldoc for device_initialize() says we must call device_put()
after calling device_initialize(). We are calling device_put() on the
error path, but are missing it from the device remove path. This causes
release() to never get called for the devices on remove.
Let's add the missing put_device() calls for both serial ctrl and
port devices.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20230804090909.51529-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_map_pram() and cpm_uart_unmap_pram() are very
similar for CPM1 and CPM2.
On CPM1 cpm_uart_map_pram() uses of_iomap() while CPM2 uses
of_address_to_resource()/ioremap(). CPM2 version will also
work on CPM1.
On CPM2 cpm_uart_map_pram() and cpm_uart_unmap_pram() has a special
handling for SMC. Just gate it by an IS_ENABLED(CONFIG_CPM2).
So move the CPM2 version into cpm_uart_core.c which is the only
user of those two fonctions and refactor to also handle CPM1 as
mentionned above.
PROFF_SMC_SIZE is only defined for SMC2 and used only there. To make
it simple, just use the numerical value 64, this is the only place
it is used and anyway there's already the same numerical value for
the alignment.
Use cpm_muram_alloc() instead of cpm_dpalloc() macro.
Then cpm_uart_cpm1.c and cpm_uart_cpm2.c are now empty and go away.
Replace printk(KERN_WARN by pr_warn( to make checkpatch happier.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/44a266106c421319aa8e700c2db52d5dcd652c0f.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_freebuf() is identical for CPM1 and CPM2.
cpm_uart_allocbuf() only has a small difference between CPM1 and CPM2
as shown below:
CPM1:
if (is_con) {
/* was hostalloc but changed cause it blows away the */
/* large tlb mapping when pinning the kernel area */
mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8));
dma_addr = (u32)cpm_dpram_phys(mem_addr);
} else
mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
GFP_KERNEL);
CPM2:
if (is_con) {
mem_addr = kzalloc(memsz, GFP_NOWAIT);
dma_addr = virt_to_bus(mem_addr);
}
else
mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
GFP_KERNEL);
Refactor this by using IS_ENABLED(CONFIG_CPM1)
and move both functions in cpm_uart_core.c as they are used only there.
While doing this, add the necessary casts to silence sparse for the CPM1
part. This is because a dma alloc is not expected to be an iomem but
for CPM1 as we use DPRAM this is seen as iomem.
Also replace calls to cpm_dpxxxx() by relevant cpm_muram_xxxx() calls.
This is needed at least for cpm_dpram_phys() which is only defined
for CPM1. Just do the same for all so that cpm_dpxxxx() macros can get
droped in the future.
To silence checkpatch, replace printk(KERN_ERR by pr_err( and display
function name instead of hard coded filename. Also replace
mem_addr == NULL by !mem_addr.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/606dfdd258a4f2f2882e2e189bef37526bb3b499.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPMFCR_EB is the same as SMC_EB and is defined
for both CPM1 and CPM2.
CPMFCR_GBL is defined as 0 for CPM1.
Therefore the CPM2 version of cpm_set_scc_fcr() and
cpm_set_smc_fcr() can be used on both CPM1 and CPM2.
And cpm_set_brg() is already identical and just a
wrapper of cpm_setbrg().
In addition those three fonctions are only called once
from cpm_uart_core.c, so just replace the calls with
the content of the CPM2 versions of them.
And DPRAM_BASE is identical so can go in cpm_uart.h. While
moving it, use cpm_muram_addr() directly instead of the
cpm_dpram_addr() macro and remove __force tag which isn't needed.
Then cpm_uart_cpm1.h and cpm_uart_cpm2.h go away.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/6920e61fd362961ae1aeda897c8bfe1efacdc9dc.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_baudrate() is just a trivial wrapper to get_baudrate().
Use get_baudrate() directly and remove assignment in if condition.
And also remove uart_clock() which is not used since
commit 0b2a2e5b77 ("cpm_uart: Remove !CONFIG_PPC_CPM_NEW_BINDING
code")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/4d497386f576a3df768e44a04f9bb512e424c311.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_init_portdesc()
smc1_lineif()
smc2_lineif()
scc1_lineif()
scc2_lineif()
scc3_lineif()
scc4_lineif()
Those functions were removed by commit 0b2a2e5b77 ("cpm_uart: Remove
!CONFIG_PPC_CPM_NEW_BINDING code"). Remove stale prototypes.
UART_SMC{1..2} and UART_SCC{1..4} and SCC_WAIT_CLOSING macros are not
used anymore since the above commit.
cpm_uart_ports[] isn't used outside cpm_uart_core.c since the
same commit, so make it static.
cpm_uart_init_smc() and cpm_uart_init_scc() don't need a forward
declaration.
FLAG_DISCARDING and IS_DISCARDING have never been used since at
least 2.6.12 and the start of git repository for kernel.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/96ef20ae1df056d1b7967871ba6e27e5b5aaeea6.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module_mcb_driver() will set "THIS_MODULE" to driver.owner when
register a mcb_driver driver, so it is redundant initialization to set
driver.owner in mcb_driver statement. Remove it for clean code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230804100843.100348-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a warning reported by coccinelle:
./drivers/tty/serial/8250/8250_men_mcb.c:226:6-19: WARNING:
Unsigned expression compared with zero: data -> line [ i ] < 0
The array "line" of serial_8250_men_mcb_data is used to record the
registered serial port. When register a port failed, it will return
an error code, but the type of "line" is "unsigned int", causing
the error code to reverse. Modify the type of "data -> line" to solve
this problem.
Fixes: 2554e6ba28 ("8250_men_mcb: Read num ports from register data.")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230803142053.1308926-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Any unprivileged user can attach N_GSM0710 ldisc, but it requires
CAP_NET_ADMIN to create a GSM network anyway.
Require initial namespace CAP_NET_ADMIN to do that.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Link: https://lore.kernel.org/r/20230731185942.279611-1-cascardo@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data->line[i] is defined as unsigned int type, if(data->line[i] < 0)
is invalid, so replace data->line[i] with res.
./drivers/tty/serial/8250/8250_men_mcb.c:223:6-19: WARNING: Unsigned expression compared with zero: data->line[i] < 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6088
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230803084753.51253-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least freeze, restore and thaw need to be set in order for the driver
to support system hibernation. The existing suspend/resume functions can
be reused since those functions don't touch the device's power state or
wakeup capability. Use the helper macros SET_SYSTEM_SLEEP_PM_OPS and
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for symmetry with similar drivers.
Signed-off-by: Anton Eliasson <anton.eliasson@axis.com>
Link: https://lore.kernel.org/r/20230803-samsung_tty_pm_ops-v1-1-1ea7be72194d@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a85a6c86c2 ("driver core: platform: Clarify that
IRQ 0 is invalid"), there is no possible for
platform_get_irq() to return 0. Use the return value
from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230803091712.596987-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As &info->lock is acquired by slgt_interrupt() under irq context, other
process context code acquiring the lock should disable irq, otherwise
deadlock could happen if the irq preempt the execution while the
lock is held in process context on the same CPU.
Lock acquisition inside set_params32() does not disable irq, and this
function is called by slgt_compat_ioctl() from process context.
Possible deadlock scenario:
slgt_compat_ioctl()
-> set_params32()
-> spin_lock(&info->lock)
<irq>
-> slgt_interrupt()
-> spin_lock(&info->lock); (deadlock here)
This flaw was found by an experimental static analysis tool I am developing
for irq-related deadlock. x86_64 allmodconfig using gcc shows no new
warning.
The patch fixes the potential deadlock by spin_lock_irqsave() like other
lock acquisition sites.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230728123901.64225-1-dg573847474@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Members vc_col, vc_rows and vc_size_row of the struct vc_data have been
initialized in visual_init(), so it is no longer needed to initialize
them in vc_init() again.
Signed-off-by: oushixiong <oushixiong@kylinos.cn>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230803065409.461031-1-oushixiong@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a warning reported by coccinelle:
./drivers/tty/serial/ma35d1_serial.c:791:3-8:
No need to set .owner here. The core will do it.
The module_platform_driver() will set "THIS_MODULE" to driver.owner
when register a driver for platform-level devices, so it is redundant
initialization to set driver.owner in ma35d1serial_driver statement.
Remove it to silence the warning.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230803032353.3045221-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While fixing DEVNAME to be more usable, I broke serial_base_match() as the
ctrl and port prefix for device names seemed unnecessary.
The prefixes are still needed by serial_base_match() to probe the serial
base controller port, and serial tx is now broken.
Let's fix the issue by checking against dev->type and drv->name instead
of the prefixes that are no longer in the DEVNAME.
Fixes: 1ef2c2df11 ("serial: core: Fix serial core controller port name to show controller id")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202308021529.35b3ad6c-oliver.sang@intel.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230803071034.25571-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are missing the serial core controller id for the serial core port
name. Let's fix the issue for sane sysfs output, and to avoid issues
addressing serial ports later on.
And as we're now showing the controller id, the "ctrl" and "port" prefix
for the DEVNAME become useless, we can just drop them. Let's standardize on
DEVNAME:0 for controller name, where 0 is the controller id. And
DEVNAME:0.0 for port name, where 0.0 are the controller id and port id.
This makes the sysfs output nicer, on qemu for example:
$ ls /sys/bus/serial-base/devices
00:04:0 serial8250:0 serial8250:0.2
00:04:0.0 serial8250:0.1 serial8250:0.3
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230725054216.45696-4-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core port id should be serial core controller specific port
instance, which is not always the port->line index.
For example, 8250 driver maps a number of legacy ports, and when a
hardware specific device driver takes over, we typically have one
driver instance for each port. Let's instead add port->port_id to
keep track serial ports mapped to each serial core controller instance.
Currently this is only a cosmetic issue for the serial core port device
names. The issue can be noticed looking at /sys/bus/serial-base/devices
for example though. Let's fix the issue to avoid port addressing issues
later on.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230725054216.45696-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not read the data register to clear the error flags for lpuart32
platforms, the additional read may cause the receive FIFO underflow
since the DMA has already read the data register.
Actually all lpuart32 platforms support write 1 to clear those error
bits, let's use this method to better clear the error flags.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230801022304.24251-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After walking and trying to clean up the worst in the driver, I came
across the pci_driver::remove() _empty_ implementation. That would crash
the system at least during hot-unplug (or write to remove in sysfs).
There are many other problems:
* Initialization + deinitialization apparently comes from no-hotplug
support age. It needs a rewrite.
* Hairy debug macros. Drop them.
* Use of self-baked lists. Replace by list.
* The order of the functions should be inverted and fwd decls dropped.
* Coding style from the stone age. Fix.
* I assume there are many bugs, but the code is unreadable at times, so
hard to judge. There is one example posted [1].
I was able to find only one user back in 2016. So mark the driver as
BROKEN for some time. Either someone will notice and we can bring the
driver to this century. Or we will drop it completely if noone cares.
[1] https://lore.kernel.org/all/20230728123901.64225-1-dg573847474@gmail.com/
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Chengfeng Ye <dg573847474@gmail.com>
Link: https://lore.kernel.org/r/20230731090002.15680-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
