It may cause confict between constraint variable read and write if
there is more than one stream running. Move rate constraint function to
probe() can avoid it.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
The imx95 driver requests the necessary mailbox channels during imx-dsp's
probe operation. If WAKEUP domain is shut down during system suspend, MU7A
(used by Linux side) will end up losing its register state. This means that
GI's will end up being masked when the system is resumed (since GIER is set
to 0x0, which means all GI's are masked). As such, SOF will assert the GIP
bits required for triggering an interrupt on Linux side but no interrupt
will be triggered since GI's are masked, thus resulting on a crash on
Linux side as it will assume that the firmware did not boot.
This was reproduced using the following steps:
1) Put Linux into suspend-to-RAM state by running:
echo 'mem' > /sys/power/state
2) Put SM into idle mode by running:
idle
3) Resume the system by running:
wakeupsource
What seems to happen is that if all CPUs are either in STOP/SLEEP
state and SM is put into idle state it will attempt to system suspend,
during which WAKEUP domain is powered off, thus leading to the
aforementioned register state loss. If SM is not put into idle state,
then WAKEUP domain is not powered off, thus if step 2) is left out then
everything will work as expected.
To fix this, make sure the mailbox channels are requested during resume()
and released during suspend(). This way, by requesting the mailbox
channels during resume() we make sure to unmask the GI's used in firmware
communcation.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
RM has incorrect recommended volume range settings. There's big noise
with high volume values. Constrain the adjustable volume range to 0~7
as a software workaround.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
On i.MX8MM the register of volume control has positive and negative
values. It is different from other platforms like i.MX8MP and i.MX93
which only have positive values. Add a volume_sx flag to use SX_TLV
volume control for this kind of platform. Use common TLV volume control
for other platforms.
Fixes: cdfa92eb90 ("ASoC: fsl_micfil: Correct the number of steps on SX controls")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Previously the mclk is enabled in probe() stage, which
is not necessary. Move mclk enablement to hw_params()
and mclk disablement to hw_free() will be more efficient.
'mclk_flag' is used for this case.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1727424031-19551-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The last parameter 1 means BIT(0), which should be the
correct BIT(X).
Fixes: 47a70e6fc9 ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://patch.msgid.link/1727424031-19551-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The wrong preamble of IEC958 received means the order of channels is
wrong. To avoid channel swap, reset the DMAC path.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Chancel Liu <chancel.liu@nxp.com>
On the i.MX9x platforms, the mask of FIFO watermark
is 0x1F, on i.MX8x platforms, the mask of FIFO watermark
is 0X7. So use the mask 0x1F for all platforms to make them
compatible.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1721897694-6088-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SOF driver for i.MX95 board. The firmware runs on
the CM7 core, which is part of a LM started and shutdown
by Linux as required.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
[ Upstream commit 38cc0334ba ]
Clang static checker (scan-build) warning:
sound/soc/codecs/peb2466.c:232:8:
Assigned value is garbage or undefined [core.uninitialized.Assign]
232 | *val = tmp;
| ^ ~~~
When peb2466_read_byte() fails, 'tmp' will have a garbage value.
Add a judgemnet to avoid this problem.
Fixes: 227f609c7c ("ASoC: codecs: Add support for the Infineon PEB2466 codec")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://patch.msgid.link/20240911115448.277828-1-suhui@nfschina.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e83957e8d ]
This fixes the LRCLK polarity for sun8i-h3 and sun50i-h6 in i2s mode
which was wrongly inverted.
The LRCLK was being set in reversed logic compared to the DAI format:
inverted LRCLK for SND_SOC_DAIFMT_IB_NF and SND_SOC_DAIFMT_NB_NF; normal
LRCLK for SND_SOC_DAIFMT_IB_IF and SND_SOC_DAIFMT_NB_IF. Such reversed
logic applies properly for DSP_A, DSP_B, LEFT_J and RIGHT_J modes but
not for I2S mode, for which the LRCLK signal results reversed to what
expected on the bus. The issue is due to a misinterpretation of the
LRCLK polarity bit of the H3 and H6 i2s controllers. Such bit in this
case does not mean "0 => normal" or "1 => inverted" according to the
expected bus operation, but it means "0 => frame starts on low edge" and
"1 => frame starts on high edge" (from the User Manuals).
This commit fixes the LRCLK polarity by setting the LRCLK polarity bit
according to the selected bus mode and renames the LRCLK polarity bit
definition to avoid further confusion.
Fixes: dd657eae81 ("ASoC: sun4i-i2s: Fix the LRCK polarity")
Fixes: 73adf87b7a ("ASoC: sun4i-i2s: Add support for H6 I2S")
Signed-off-by: Matteo Martelli <matteomartelli3@gmail.com>
Link: https://patch.msgid.link/20240801-asoc-fix-sun4i-i2s-v2-1-a8e4e9daa363@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0be875c5b ]
The SOF topology loading function sets the device name for the platform
component link. This should be unset when unloading the topology,
otherwise a machine driver unbind/bind or reprobe would complain about
an invalid component as having both its component name and of_node set:
mt8186_mt6366 sound: ASoC: Both Component name/of_node are set for AFE_SOF_DL1
mt8186_mt6366 sound: error -EINVAL: Cannot register card
mt8186_mt6366 sound: probe with driver mt8186_mt6366 failed with error -22
This happens with machine drivers that set the of_node separately.
Clear the SOF link platform name in the topology unload callback.
Fixes: 311ce4fe76 ("ASoC: SOF: Add support for loading topologies")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20240821041006.2618855-1-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6781b962d9 ]
When Tegra audio drivers are built as part of the kernel image,
TIMEOUT_ERR is observed from cbb-fabric. Following is seen on
Jetson AGX Orin during boot:
[ 8.012482] **************************************
[ 8.017423] CPU:0, Error:cbb-fabric, Errmon:2
[ 8.021922] Error Code : TIMEOUT_ERR
[ 8.025966] Overflow : Multiple TIMEOUT_ERR
[ 8.030644]
[ 8.032175] Error Code : TIMEOUT_ERR
[ 8.036217] MASTER_ID : CCPLEX
[ 8.039722] Address : 0x290a0a8
[ 8.043318] Cache : 0x1 -- Bufferable
[ 8.047630] Protection : 0x2 -- Unprivileged, Non-Secure, Data Access
[ 8.054628] Access_Type : Write
[ 8.106130] WARNING: CPU: 0 PID: 124 at drivers/soc/tegra/cbb/tegra234-cbb.c:604 tegra234_cbb_isr+0x134/0x178
[ 8.240602] Call trace:
[ 8.243126] tegra234_cbb_isr+0x134/0x178
[ 8.247261] __handle_irq_event_percpu+0x60/0x238
[ 8.252132] handle_irq_event+0x54/0xb8
These errors happen when MVC device, which is a child of AHUB
device, tries to access its device registers. This happens as
part of call tegra210_mvc_reset_vol_settings() in MVC device
probe().
The root cause of this problem is, the child MVC device gets
probed before the AHUB clock gets enabled. The AHUB clock is
enabled in runtime PM resume of parent AHUB device and due to
the wrong sequence of pm_runtime_enable() in AHUB driver,
runtime PM resume doesn't happen for AHUB device when MVC makes
register access.
Fix this by calling pm_runtime_enable() for parent AHUB device
before of_platform_populate() in AHUB driver. This ensures that
clock becomes available when MVC makes register access.
Fixes: 16e1bcc2ca ("ASoC: tegra: Add Tegra210 based AHUB driver")
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Signed-off-by: Ritu Chaudhary <rituc@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://patch.msgid.link/20240823144342.4123814-3-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cc509edbe ]
Use get_unaligned_be16 instead of be16_to_cpup and get_unaligned_be32
instead of be32_to_cpup for potentially broken alignment.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20240707083011.98-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b4a90b543d upstream.
When using kernel with the following extra config,
- CONFIG_KASAN=y
- CONFIG_KASAN_GENERIC=y
- CONFIG_KASAN_INLINE=y
- CONFIG_KASAN_VMALLOC=y
- CONFIG_FRAME_WARN=4096
kernel detects that snd_pcm_suspend_all() access a freed
'snd_soc_pcm_runtime' object when the system is suspended, which
leads to a use-after-free bug:
[ 52.047746] BUG: KASAN: use-after-free in snd_pcm_suspend_all+0x1a8/0x270
[ 52.047765] Read of size 1 at addr ffff0000b9434d50 by task systemd-sleep/2330
[ 52.047785] Call trace:
[ 52.047787] dump_backtrace+0x0/0x3c0
[ 52.047794] show_stack+0x34/0x50
[ 52.047797] dump_stack_lvl+0x68/0x8c
[ 52.047802] print_address_description.constprop.0+0x74/0x2c0
[ 52.047809] kasan_report+0x210/0x230
[ 52.047815] __asan_report_load1_noabort+0x3c/0x50
[ 52.047820] snd_pcm_suspend_all+0x1a8/0x270
[ 52.047824] snd_soc_suspend+0x19c/0x4e0
The snd_pcm_sync_stop() has a NULL check on 'substream->runtime' before
making any access. So we need to always set 'substream->runtime' to NULL
everytime we kfree() it.
Fixes: a72706ed82 ("ASoC: codec2codec: remove ephemeral variables")
Signed-off-by: robelin <robelin@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://patch.msgid.link/20240823144342.4123814-2-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4684a2df9c ]
We find that we need to set snd_jack_types to 0. If not,
there will be a probability of button detection errors
Signed-off-by: Zhang Yi <zhangyi@everest-semi.com>
Link: https://patch.msgid.link/20240807025356.24904-2-zhangyi@everest-semi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23a58b782f ]
Lenovo Thinkpad E14 Gen 6 (model type 21M3)
needs a quirk entry for internal mic to work.
Signed-off-by: Krzysztof Stępniak <kfs.szk@gmail.com>
Link: https://patch.msgid.link/20240807001219.1147-1-kfs.szk@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c118478665 ]
Add support for the internal microphone for HP 14-em0002la laptop using
a quirk entry.
Signed-off-by: Bruno Ancona <brunoanconasala@gmail.com>
Link: https://patch.msgid.link/20240729045032.223230-1-brunoanconasala@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a42db293e5 ]
When ACP is not powered on by default, acp power on sequence explicitly
invoked by programming pgfsm control mask. The existing implementation
checks the same PGFSM status mask and programs the same PGFSM control mask
in all ACP variants which breaks acp power on sequence for ACP6.0 and
ACP6.3 variants. So to fix this issue, update ACP pgfsm control mask and
status mask based on acp descriptor rev field, which will vary based on
acp variant.
Fixes: 846aef1d7c ("ASoC: SOF: amd: Add Renoir ACP HW support")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20240816070328.610360-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 164199615a ]
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from platform_device_id table.
Fixes: 9d8a7be88b ("ASoC: amd: acp: Add legacy sound card support for Chrome audio")
Signed-off-by: Yuntao Liu <liuyuntao12@huawei.com>
Link: https://patch.msgid.link/20240815084923.756476-1-liuyuntao12@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 576a0b71b5 ]
In the existing IPC support, the reply to each IPC message is handled in
an IRQ thread. The assumption is that the IRQ thread is scheduled without
significant delays.
On an experimental (iow, buggy) kernel, the IRQ thread dealing with the
reply to the last IPC message before powering-down the DSP can be delayed
by several seconds. The IRQ thread will proceed with register accesses
after the DSP is powered-down which results in a kernel crash.
While the bug which causes the delay is not in the audio stack, we must
handle such cases with defensive programming to avoid such crashes.
Call synchronize_irq() before proceeding to power down the DSP to make
sure that no irq thread is pending execution.
Closes: https://github.com/thesofproject/linux/issues/4608
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231012191850.147140-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44f37b6ce0 ]
Checks the index computed by the virq offset before printing the
error condition in cs35l45_spk_safe_err() handler.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Vlad Karpovich <vkarpovi@opensource.cirrus.com>
Acked-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230831162042.471801-1-vkarpovi@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Set FCONT bit in control register to avoid the channel swap
issue after SAI xrun.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
The static snd_soc_dai_link_components cause conflict for multiple
instances of this generic driver. For example, when there is
wm8962 and MQS case enabled together, the contaminated
snd_soc_dai_link_components will cause another device probe fail.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
commit e0e7bc2cbe upstream.
Instead of using very long macro name, assign it to shorter variable
and use it instead. While doing that, we can reduce multiple if checks
using this define to one.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240603102818.36165-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5003d0ce5c ]
With PREEMPT_RT enabled a spinlock_t becomes a sleeping lock.
This is usually not a problem with spinlocks used in IRQ context since
IRQ handlers get threaded. However, if IRQF_ONESHOT is set, the primary
handler won't be force-threaded and runs always in hardirq context. This is
a problem because spinlock_t requires a preemptible context on PREEMPT_RT.
In this particular instance, regmap mmio uses spinlock_t to protect the
register access and IRQF_ONESHOT is set on the IRQ. In this case, it is
actually better to do everything in threaded handler and it solves the
problem with PREEMPT_RT.
Reported-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Closes: https://lore.kernel.org/linux-amlogic/20240729131652.3012327-1-avkrasnov@salutedevices.com
Suggested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Fixes: b11d26660d ("ASoC: meson: axg-fifo: use threaded irq to check periods")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/20240807162705.4024136-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7354eb7f15 ]
Default firmware shipped in open source are not licensed for 3P
libraries, therefore topologies should not reference them.
If a OS wants to use 3P (that they have licensed) then they should use
the appropriate topology override mechanisms.
Fixes: 8a7d5d85ed ("ASoC: SOF: mediatek: mt8195: Add devicetree support to select topologies")
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Cc: Wojciech Macek <wmacek@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20240731212153.921327-1-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b99068d5e ]
This patch addresses a regression in the ASoC STI drivers that was
introduced in Linux version 6.6.y. The issue originated from a series of
patches (see https://lore.kernel.org/all/87wmy5b0wt.wl-kuninori.morimoto.gx@renesas.com/)
that unintentionally omitted necessary probe functions for the player
and reader components.
Probe function in `sound/soc/sti/sti_uniperif.c:415` is being replaced
by another probe function located at `sound/soc/sti/sti_uniperif.c:453`,
which should instead be derived from the player and reader components.
This patch correctly reinserts the missing probe entries,
restoring the intended functionality.
Fixes: 9f625f5e6c ("ASoC: sti: merge DAI call back functions into ops")
Signed-off-by: Jerome Audu <jau@free.fr>
Link: https://patch.msgid.link/20240727-sti-audio-fix-v2-1-208bde546c3f@free.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcb6631d05 ]
Device has up to WSA884X_MAX_SWR_PORTS number of ports and the array
assigned to prop.sink_dpn_prop has 0..WSA884X_MAX_SWR_PORTS-1 elements.
On the other hand, GENMASK(high, low) creates an inclusive mask between
<high, low>, so we need the mask from 0 up to WSA884X_MAX_SWR_PORTS-1.
Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().
Fixes: aa21a7d4f6 ("ASoC: codecs: wsa884x: Add WSA884x family of speakers")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-6-d4d7a8b56f05@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1bc5c324b ]
Add support to parse static master port map information from device tree.
This is required for correct port mapping between soundwire device and
master ports.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20240626-port-map-v2-4-6cc1c5608cdd@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: dcb6631d05 ("ASoC: codecs: wsa884x: Correct Soundwire ports mask")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6801ac36f2 ]
Device has up to WSA883X_MAX_SWR_PORTS number of ports and the array
assigned to prop.sink_dpn_prop has 0..WSA883X_MAX_SWR_PORTS-1 elements.
On the other hand, GENMASK(high, low) creates an inclusive mask between
<high, low>, so we need the mask from 0 up to WSA883X_MAX_SWR_PORTS-1.
Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().
Fixes: 43b8c7dc85 ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-5-d4d7a8b56f05@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb11c3bb64 ]
Device has up to WSA881X_MAX_SWR_PORTS number of ports and the array
assigned to prop.sink_dpn_prop has 0..WSA881X_MAX_SWR_PORTS-1 elements.
On the other hand, GENMASK(high, low) creates an inclusive mask between
<high, low>, so we need the mask from 0 up to WSA881X_MAX_SWR_PORTS-1.
Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().
Fixes: a0aab9e140 ("ASoC: codecs: add wsa881x amplifier support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-4-d4d7a8b56f05@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f6fb03dae ]
Device has up to WCD938X_MAX_SWR_PORTS number of ports and the array
assigned to prop.src_dpn_prop and prop.sink_dpn_prop has
0..WCD938X_MAX_SWR_PORTS-1 elements. On the other hand, GENMASK(high,
low) creates an inclusive mask between <high, low>, so we need the mask
from 0 up to WCD938X_MAX_SWR_PORTS-1.
Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().
Fixes: 16572522ae ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-2-d4d7a8b56f05@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c7822216 ]
This function has a reversed if statement so it's either a no-op or it
leads to a NULL dereference.
Fixes: b195acf526 ("ASoC: tas2781: Fix wrong loading calibrated data sequence")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/18a29b68-cc85-4139-b7c7-2514e8409a42@stanley.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9931f7d5d2 ]
the Intel kbuild bot reports a link failure when IOSF_MBI is built-in
but the Merrifield driver is configured as a module. The
soc-intel-quirks.h is included for Merrifield platforms, but IOSF_MBI
is not selected for that platform.
ld.lld: error: undefined symbol: iosf_mbi_read
>>> referenced by atom.c
>>> sound/soc/sof/intel/atom.o:(atom_machine_select) in archive vmlinux.a
This patch forces the use of the fallback static inline when IOSF_MBI is not reachable.
Fixes: 536cfd2f37 ("ASoC: Intel: use common helpers to detect CPUs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407160704.zpdhJ8da-lkp@intel.com/
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20240722083002.10800-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2038c12e8 ]
Setting ACP ACLK as clock source when ACP enters D0 state causing
firmware load failure, as per design clock source should be internal
clock.
Remove acp_clkmux_sel field so that ACP will use internal clock
source when ACP enters into D0 state.
Fixes: d0dab6b76a ("ASoC: SOF: amd: Add sof support for vangogh platform")
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20240718062004.581685-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2634f745ea ]
According to Documentation/devicetree/bindings/dsp/fsl,dsp.yaml
fsl,dsp-ctrl is a phandle to syscon block so we need to use correct
function to retrieve it.
Currently there is no SOF DSP DTS merged into mainline so there is no
need to support the old way of retrieving the dsp control node.
Fixes: 9ba23717b2 ("ASoC: SOF: imx8m: Implement DSP start")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://patch.msgid.link/20240715151653.114751-1-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e6fc5fcaef upstream.
The DMA Link ID is set to the IPC message's primary during dai_config,
which is only during hw_params.
During xrun handling the hw_params is not called and the DMA Link ID
information will be lost.
All other fields in the message expected to be 0 for re-configuration, only
the DMA Link ID needs to be preserved and the in case of repeated
dai_config, it is correctly updated (masked and then set).
Cc: stable@vger.kernel.org
Fixes: ca5ce0caa6 ("ASoC: SOF: ipc4/intel: Add support for chained DMA")
Link: https://github.com/thesofproject/linux/issues/5116
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240724081932.24542-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e625999023 upstream.
devm_kasprintf() can return a NULL pointer on failure but this returned
value is not checked.
Fix this lack and check the returned value.
Fixes: 075c7125b1 ("ASoC: fsl: Add support for QMC audio")
Cc: stable@vger.kernel.org
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://patch.msgid.link/20240701113038.55144-2-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5080808c33 ]
acpi_get_first_physical_node() can return NULL in several cases (no such
device, ACPI table error, reference count drop to 0, etc).
Existing check just emit error message, but doesn't perform return.
Then this NULL pointer is passed to devm_acpi_dev_add_driver_gpios()
where it is dereferenced.
Adjust this error handling by adding error code return.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 02527c3f23 ("ASoC: amd: add Machine driver for Jadeite platform")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Link: https://patch.msgid.link/20240703191007.8524-1-amishin@t-argos.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
