Update error flags with regulation out if regulator is on & power
good status bit is set
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20221117184022.1808508-1-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC7132.
The relevant registers in the LTC7132 are identical to the LTC7880.
So it's just a matter of adding the chip id.
Signed-off-by: Felix Nieuwenhuizen <Felix.Nieuwenhuizen@etas.com>
Link: https://lore.kernel.org/r/20221027145135.31802-1-Felix.Nieuwenhuizen@etas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit 54cc3dbfc1.
Zev Weiss reports that the reverted patch may cause a regulator
undercount. Here is his report:
... having regulator-dummy set as a supply on my PMBus regulators
(instead of having them as their own top-level regulators without
an upstream supply) leads to enable-count underflow errors when
disabling them:
# echo 0 > /sys/bus/platform/devices/efuse01/state
[ 906.094477] regulator-dummy: Underflow of regulator enable count
[ 906.100563] Failed to disable vout: -EINVAL
[ 136.992676] reg-userspace-consumer efuse01: Failed to configure state: -22
Zev reports that reverting the patch fixes the problem. So let's do that
for now.
Fixes: 54cc3dbfc1 ("hwmon: (pmbus) Add regulator supply into macro")
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Reported-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* New drivers
- Driver for MAX31760 fan speed controller
- Driver for TEXAS TPS546D24 Buck Converter
- Driver for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller
* Removed drivers
- Drop obsolete asus_wmi_ec_sensors driver
* Cleanups, affecting various drivers
- Use DEFINE_SIMPLE_DEV_PM_OPS where appropriate
- Remove forward declarations
- Move from strlcpy with unused retval to strscpy
- Make use of devm_clk_get_enabled()
- Drop devm_of_pwm_get()
* Other notable cleanup and improvements
- Support for additional USB devide ID and support for reporting
of rail mode via debugfs added to corsair-psu driver
- Support for aditional USB ID in nzxt-smart2 driver
- Support for Aquacomputer High Flow Next in aquacomputer_d5next driver
- Major cleanup of pwm-fan driver
- Major cleanup of mr75203 driver, and added support for new device revision
* Various other minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=8u0w
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for MAX31760 fan speed controller
- Driver for TEXAS TPS546D24 Buck Converter
- Driver for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller
Removed drivers:
- Drop obsolete asus_wmi_ec_sensors driver
Cleanups, affecting various drivers:
- Use DEFINE_SIMPLE_DEV_PM_OPS where appropriate
- Remove forward declarations
- Move from strlcpy with unused retval to strscpy
- Make use of devm_clk_get_enabled()
- Drop devm_of_pwm_get()
Other notable cleanup and improvements:
- Support for additional USB devide ID and support for reporting of
rail mode via debugfs added to corsair-psu driver
- Support for aditional USB ID in nzxt-smart2 driver
- Support for Aquacomputer High Flow Next in aquacomputer_d5next
driver
- Major cleanup of pwm-fan driver
- Major cleanup of mr75203 driver, and added support for new device
revision
And various other minor fixes and cleanups"
* tag 'hwmon-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (86 commits)
hwmon: (corsair-psu) add USB id of new revision of the HX1000i psu
hwmon: (pmbus/mp2888) Fix sensors readouts for MPS Multi-phase mp2888 controller
dt-bindings: hwmon: sensirion,shtc1: Clean up spelling mistakes and grammar
hwmon: (nct6683) remove unused variable in nct6683_create_attr_group
hwmon: w83627hf: Reorder symbols to get rid of a few forward declarations
hwmon: (ina3221) Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
hwmon: (w83627ehf) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp108) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp103) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp102) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (pwm-fan) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (nct6775) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max6639) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max31730) witch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max31722) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (ltc2947) Switch to EXPORT_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (lm90) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (it87) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (gpio-fan) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (adt7x10) Switch to EXPORT_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
...
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano).
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano).
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter).
- Fix kernel panic when KASAN is enabled as it detects use after
free when unregistering a thermal zone (Daniel Lezcano).
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano).
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong).
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano).
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano).
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki).
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano).
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar).
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang).
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing).
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada).
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki).
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan).
- Drop redundant error message from da9062-thermal (zhaoxiao).
- Drop of_match_ptr() from thermal_mmio (Jean Delvare).
-----BEGIN PGP SIGNATURE-----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=Ufw7
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"The most significant part of this update is the thermal control DT
initialization rework from Daniel Lezcano and the following conversion
of drivers to use the new API introduced by it
Apart from that, the maximum number of trip points in a thermal zone
is increased and there are some fixes and code cleanups
Specifics:
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after free
when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar)
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang)
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing)
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada)
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki)
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan)
- Drop redundant error message from da9062-thermal (zhaoxiao)
- Drop of_match_ptr() from thermal_mmio (Jean Delvare)"
* tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: core: Increase maximum number of trip points
thermal: int340x: processor_thermal: Use module_pci_driver() macro
thermal: intel_powerclamp: Remove accounting for IRQ wakes
thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash
thermal: int340x_thermal: Consolidate priv->data_vault checks
thermal: cpufreq_cooling: Check the policy first in cpufreq_cooling_register()
thermal: Drop duplicate words from comments
thermal: move from strlcpy() with unused retval to strscpy()
thermal: da9062-thermal: Drop redundant error message
thermal/drivers/thermal_mmio: Drop of_match_ptr()
thermal: gov_user_space: Do not lock thermal zone mutex
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
...
Add the pmbus driver for TEXAS tps546d24 Buck Converter.
The vout mode of tps546d24 supported relative data format,
which is not supported by the PMBus core.
Signed-off-by: Duke Du <dukedu83@gmail.com>
Link: https://lore.kernel.org/r/1662951668-9849-1-git-send-email-Duke.Du@quantatw.com
[groeck: Add __maybe_unused to tps546d24_of_match declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The code currently uses a zero margin to mean not cached, but this
results in the cache being bypassed if the (low) margin is set to zero,
leading to lots of unnecessary SMBus transactions in that case. Use a
negative value instead.
Fixes: 07fb76273d ("hwmon: (pmbus) Introduce and use cached vout margins")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220816144414.2358974-1-vincent.whitchurch@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal OF code has a new API allowing to migrate the OF
initialization to a simpler approach. The ops are no longer device
tree specific and are the generic ones provided by the core code.
Convert the ops to the thermal_zone_device_ops format and use the new
API to register the thermal zone with these generic ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linexp.org>
Link: https://lore.kernel.org/r/20220804224349.1926752-27-daniel.lezcano@linexp.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The LTC2977 regulator does not set the regulator_desc .n_voltages value
which is needed in order to let the regulator core list the regulator
voltage range.
This patch defines a regulator_desc with a voltage range, and uses it
for defining voltage resolution for regulators LTC2972/LTC2974/LTC2975/
LTC2977/LTC2978/LTC2979/LTC2980/LTM2987 based on that they all have a 16
bit ADC with the same stepwise 122.07uV resolution. It also scales the
resolution to a 1mV resolution which is easier to handle.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614095144.3472305-1-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When checking if a regulator supports a voltage range, the regulator
needs to have a list_voltage callback set to the regulator_ops or else
-EINVAL will be returned. This support does not exist for the pmbus
regulators, so this patch adds pmbus_regulator_list_voltage to the
pmbus_regulator_ops.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614093856.3470672-3-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When setting a new voltage the voltage boundaries are read every time to
check that the new voltage is within the proper range. Checking these
voltage boundaries consists of reading one of PMBUS_MFR_VOUT_MIN/
PMBUS_VOUT_MARGIN_LOW registers and then PMBUS_MFR_VOUT_MAX/
PMBUS_VOUT_MARGIN_HIGH together with writing the PMBUS_CLEAR_FAULTS
register.
Since these boundaries are never being changed, it can be cached and
thus saving unnecessary smbus transmissions.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614093856.3470672-2-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_PMBUS is y and CONFIG_DEBUG_FS is not set.
make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-, will be failed, like this:
drivers/hwmon/pmbus/pmbus_core.c:593:13: error: ‘pmbus_check_block_register’ defined but not used [-Werror=unused-function]
static bool pmbus_check_block_register(struct i2c_client *client, int page,
^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[3]: *** [drivers/hwmon/pmbus/pmbus_core.o] Error 1
make[2]: *** [drivers/hwmon/pmbus] Error 2
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [drivers/hwmon] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [drivers] Error 2
To fix building warning, use __maybe_unused to attach this func.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: c3ffc3a1ff83("hwmon: (pmbus) add a function to check the presence of a block register")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Link: https://lore.kernel.org/r/20220609120448.139907-1-renzhijie2@huawei.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add registers to debugfs:
PMBUS_MFR_ID
PMBUS_MFR_MODEL
PMBUS_MFR_REVISION
PMBUS_MFR_LOCATION
PMBUS_MFR_DATE
PMBUS_MFR_SERIAL
To reduce the number of debugfs entries, only values from page 0 are
reported. It is assumed that values of these registers are the same for
all pages. Please note that the PMBUS standard allows added registers to
be page-specific.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220601013232.801133-2-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Other functions (like pmbus_check_byte_register) cannot be used to check
the presence of a block register, because it will generate error when PEC
is used.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220601013232.801133-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Analog Devices LT7182S Dual Channel 6A, 20V PolyPhase
Step-Down Silent Switcher with Digital Power System Management.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enabling and disabling PEC for PMBus devices is currently only supported
with a debugfs attribute, which requires debugfs to be enabled and is
thus less than perfect. Take the lm90 driver as example and add a 'pec'
attribute to the I2C device if both the I2C adapter and the PMBus device
support it. Remove the now obsolete 'pec' attribute from debugfs.
Cc: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drop the redundant word 'the' in the comments following
/*
* Set PHASE registers on all pages to 0xff to ensure that phase
* specific commands will apply to all phases of a given page (rail).
* This only affects the READ_IOUT and READ_TEMPERATURE2 registers.
* READ_IOUT will return the sum of currents of all phases of a rail,
* and READ_TEMPERATURE2 will return the maximum temperature detected
* for the [the - DROP] phases of the rail.
*/
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622063231.20612-1-jiangjian@cdjrlc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make sure that the support of PEC is determined before the read of other
registers. Otherwise the validation of PEC can trigger an error on the read
of STATUS_BYTE or STATUS_WORD registers.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without the move of the code, at the second load of
the driver (or bind) the STATUS_BYTE or STATUS_WORD register is always
read with PEC enabled, which is likely to cause a read error resulting
with fail of a driver load (or bind).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220519233334.438621-1-dev_public@wujek.eu
Fixes: 75d2b2b06b ("hwmon: (pmbus) disable PEC if not enabled")
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
[groeck: Added Fixes: tags, dropped continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus core does not have operations for getting or setting voltage.
Add functions get/set voltage for the dynamic regulator framework.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220503104631.3515715-5-marten.lindahl@axis.com
[groeck: cosmetic alignment / empty line fixes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some pmbus device drivers have device tree support and
may want to use of-thermal to register a thermal zone
OF sensor for those device drivers.
This way we allow describing device tree thermal zones
for pmbus device drivers with device tree support.
This patch achieves this by registering pmbus sensors
with thermal subsystem if they are PSC_TEMPERATURE
and are providing _input hwmon interface.
Cc: Guenter Roeck <linux@roeck-us.net> (maintainer:PMBUS HARDWARE MONITORING DRIVERS)
Cc: Jean Delvare <jdelvare@suse.com> (maintainer:HARDWARE MONITORING)
Cc: linux-hwmon@vger.kernel.org (open list:PMBUS HARDWARE MONITORING DRIVERS)
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Eduardo Valentin <evalenti@kernel.org>
Link: https://lore.kernel.org/r/20220428174926.2150-1-eduval@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several of the manuals for devices supported by this driver describes
the need for a minimum wait time before the chip is ready to receive
next command.
This wait time is already implemented in the driver as a ltc_wait_ready
function with a driver defined wait time of 100 ms, and is considered
for specific devices before reading/writing data on the pmbus.
Since this driver uses the default pmbus_regulator_ops for the enable/
disable/is_enabled functions we should add a driver specific callback
for write_byte_data to prevent bypassing the wait time recommendations
for the following devices: ltc3880/ltc3882/ltc3883/ltc3884/ltc3886/
ltc3887/ltc3889/ltm4664/ltm4675/ltm4676/ltm4677/ltm4678/ltm4680/ltm4686/
ltm4700/ltc7880.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-4-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the pmbus core functions uses pmbus_read_byte_data, which does
not support driver callbacks for chip specific write operations. This
could potentially influence some specific regulator chips that for
example need a time delay before each data access.
Lets use _pmbus_read_byte_data with callback check.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-3-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the pmbus core functions uses pmbus_write_byte_data, which does
not support driver callbacks for chip specific write operations. This
could potentially influence some specific regulator chips that for
example need a time delay before each data access.
Lets add support for driver callback with _pmbus_write_byte_data.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-2-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another MAX16602 chip support to MAX16601 driver
Tested with MAX16602 works as expected.
Signed-off-by: Atif Ofluoglu <atif.ofluoglu@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CLEAR_FAULTS commands can apparently sometimes trigger catastrophic
power output glitches on the ahe-50dc, so block them from being sent
at all.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220427035109.3819-1-zev@bewilderbeest.net
Fixes: d387d88ed0 ("hwmon: (pmbus) Add Delta AHE-50DC fan control module driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Explicitly disable PEC when the client does not support it.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without a new code, at the second load of the driver
(or bind) the "flags" variable is not updated to avoid PEC usage. As a
consequence the further communication with the device is done with
the PEC enabled, which is wrong and may fail.
The implementation first disable the I2C_CLIENT_PEC flag, then the old
code enable it if needed.
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220420145059.431061-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
0-day reports:
drivers/hwmon/pmbus/xdpe12284.c:127:36: warning:
unused variable 'xdpe122_reg_desc'
This is seen if CONFIG_SENSORS_XDPE122_REGULATOR is not enabled.
Mark xdpe122_reg_desc as __maybe_unused to fix the problem.
Fixes: f53bfe4d69 ("hwmon: (xdpe12284) Add regulator support")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If there is an input undervoltage fault, reported in STATUS_INPUT
command response, there is quite likely a "Unit Off For Insufficient
Input Voltage" condition as well.
Add a constant for bit 3 of STATUS_INPUT. Update the Vin limit
attributes to include both bits in the mask for clearing faults.
If an input undervoltage fault occurs, causing a unit off for
insufficient input voltage, but the unit is off bit is not cleared, the
STATUS_WORD will not be updated to clear the input fault condition.
Including the unit is off bit (bit 3) allows for the input fault
condition to completely clear.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20220317232123.2103592-1-bjwyman@gmail.com
Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
[groeck: Dropped unnecessary ()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Current driver assume PWR_AVG and VI_AVG as 1 by default, and user needs
to set sample averaging via sysfs manually.
This patch parses the properties "adi,power-sample-average" and
"adi,volt-curr-sample-average" from device tree, and setting sample
averaging during probe. Input value must be one of value in the
list [1, 2, 4, 8, 16, 32, 64, 128].
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Link: https://lore.kernel.org/r/20220302123817.27025-2-potin.lai@quantatw.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for another Infineon Multi-phase controller chip. The
xdpe11280 uses linear instead of vid data format for VOUT. Detect
VOUT_MODE format during identification and skip the xdpe122 related
adaptions in case it is linear.
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/fa6a4b636a05ecb337d132824efca2545188a2a2.1646214248.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add regulator supply into PWBUS_REGULATOR macro. This makes it optional
to define a vin-supply in DT. Not defining a supply will add a dummy
regulator supply instead and only cause the following debug output:
```
Looking up vin-supply property in node [...] failed
```
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/58f2ff7b90233fad3d7ae2e9d66d5192e2c1ac01.1645437439.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While these chips aren't strictly advertised as voltage regulators per
se, they (aside from the lm25056) support the PMBus OPERATION command
to enable and disable their outputs and have status bits for reporting
various warnings and faults, and can hence usefully support all the
pmbus_regulator_ops operations.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220219000742.20126-1-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The various PMBus status bits don't all map perfectly to the more
limited set of REGULATOR_ERROR_* flags, but there's a reasonable
number where they correspond well enough.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220219000359.19985-1-zev@bewilderbeest.net
[groeck: Added missing locking]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On PMBUS devices with multiple pages, the regulator ops need to be
protected with the update mutex. This prevents accidentally changing
the page in a separate thread while operating on the PMBUS_OPERATION
register.
Tested on Infineon xdpe11280 while a separate thread polls for sensor
data.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/b991506bcbf665f7af185945f70bf9d5cf04637c.1645804976.git.sylv@sylv.io
Fixes: ddbb4db4ce ("hwmon: (pmbus) Add regulator support")
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Almost all fault/warning bits in pmbus status registers remain set even
after fault/warning condition are removed. As per pmbus specification
these faults must be cleared by user.
Modify hwmon behavior to clear fault/warning bit after fetching data if
fault/warning bit was set. This allows to get fresh data in next read.
Signed-off-by: Vikash Chandola <vikash.chandola@linux.intel.com>
Link: https://lore.kernel.org/r/20220222131253.2426834-1-vikash.chandola@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_PM is not enabled, the following warning is reported.
drivers/hwmon/pmbus/ir38064.c:54:34: warning:
unused variable 'ir38064_of_match'
Mark it as __maybe_unused.
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arthur Heymans <arthur.heymans@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip series supported by this driver are voltage regulators, so expose
them to the regulator subsystem.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20211213142814.264802-4-arthur.heymans@9elements.com
[groeck: Added brief patch description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The IR38060, IR38164 and IR38263 can be supported using this driver.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Arthur Heymans <arthur.heymans@9elements.com>
Link: https://lore.kernel.org/r/20211213142814.264802-2-arthur.heymans@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This device is an integrated module of the Delta AHE-50DC Open19 power
shelf. I haven't been able to procure any proper documentation for
it, but it seems to be a (somewhat minimally) PMBus-compliant device.
It provides four fan speeds, four temperatures (three standard and one
manufacturer-specific via a virtual second page), and a vin reading.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20211208213703.2577-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There are multiple power supplies that will indicate
CFFPS_CCIN_VERSION_1, use the manufacturer ID to determine if it should
be treated as version cffps1 or version cffps2.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20211004144339.2634330-2-bjwyman@gmail.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The appropriate mantissa values for the lm25066 family's direct-format
current and power readings are a function of the sense resistor
employed between the SENSE and VIN pins of the chip. Instead of
assuming that resistance is always the same 1mOhm as used in the
datasheet, allow it to be configured via a device-tree property
("shunt-resistor-micro-ohms").
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-8-zev@bewilderbeest.net
[groeck: Fixed checkpatch warnings]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-7-zev@bewilderbeest.net
[groeck: Replaced reference to reasoning with reasoning, fixed checkpatch
warnings, fixed compile warning comparing of_id->data w/ i2c_id->driver_data]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Maintaining this manually is error prone (there are currently only
five chips supported, not six); gcc can do it for us automatically.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 666c14906b ("hwmon: (pmbus/lm25066) Drop support for LM25063")
Link: https://lore.kernel.org/r/20210928092242.30036-5-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
At least as of Revision J, the datasheet has a slightly different
value than what we'd had in the driver.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-3-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With the exception of the lm5066i, all the devices handled by this
driver had been missing their offset ('b') coefficients for direct
format readings.
Cc: stable@vger.kernel.org
Fixes: 58615a94f6 ("hwmon: (pmbus/lm25066) Add support for LM25056")
Fixes: e53e6497fc ("hwmon: (pmbus/lm25066) Refactor device specific coefficients")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add missed attribute for reading POUT from page 1.
It is supported by device, but has been missed in initial commit.
Fixes: 2c6fcbb211 ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927070740.2149290-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.
The Witherspoon power supply returns the bytes in MSB/LSB order.
The Rainier power supply returns the bytes in LSB/MSB order.
The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.
Tested:
Witherspoon before: 3148. Witherspoon after: 3148.
Rainier before: 53255. Rainier after: 2000.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210928205051.1222815-1-bjwyman@gmail.com
[groeck: Replaced yoda programming]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
BPD-RS600 modules running firmware v5.70 misreport the MFR_PIN_MAX.
The indicate a maximum of 1640W instead of 700W. Detect the invalid
reading and return a sensible value instead.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210812014000.26293-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In the initial implementation a number of PMBUS_x_WARN_LIMITs were
mapped to MFR fields. This was incorrect as these MFR limits reflect the
rated limit as opposed to a limit which will generate warning. Instead
return -ENXIO like we were already doing for other WARN_LIMITs.
Subsequently these rated limits have been exposed generically as new
fields in the sysfs ABI so the values are still available.
Fixes: 15b2703e5e ("hwmon: (pmbus) Add driver for BluTek BPA-RS600")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210812014000.26293-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When doing a PMBus write for the LED control on the IBM Common Form
Factor Power Supplies (ibm-cffps), the DAh command requires that bit 7
be low and bit 6 be high in order to indicate that you are truly
attempting to do a write.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20210806225131.1808759-1-bjwyman@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The BPD-RS600 is the DC version of the BPA-RS600. The PMBUS interface is
the same between the two models. Keep the same compatible string but
accept either BPA-RS600 or BPD-RS600 in the PMBUS_MFR_MODEL.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210708220618.23576-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The debugfs_create_dir() function returns error pointers, it doesn't
return NULL. But debugfs functions don't need to be checked in normal
situations and we can just delete this code.
Fixes: 1f442e213ce5 ("hwmon: (pmbus) Add driver for Delta DPS-920AB PSU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YMyjmR54ErLtc1sH@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds support for the Delta DPS-920AB PSU.
Only missing feature is fan control which the PSU supports.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210607103431.2039073-1-robert.marko@sartura.hr
[groeck: Add MODULE_IMPORT_NS(PMBUS);]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hardware monitoring support for Flex power interface modules PIM4006,
PIM4328 and PIM4820.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow the use of a phase function even if it does not exist on
the associated page.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading and decoding direct format coefficients to
the PMBus core driver. If the new flag PMBUS_USE_COEFFICIENTS_CMD
is set, the driver will use the COEFFICIENTS register together with
the information in the pmbus_sensor_attr structs to initialize
relevant coefficients for the direct mode format.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
[groeck: Initialize ret with -EINVAL in pmbus_init_coefficients()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips respond with invalid data when reading the WRITE_PROTECT
register. For such chips, this flag should be set so that the PMBus core
driver doesn't use the WRITE_PROTECT command to determine its behavior.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, for Packet Error Checking (PEC) only the controller
is checked for support. This causes problems on the cisco-8000
platform where a SMBUS transaction errors are observed. This is
because PEC has to be enabled only if both controller and
adapter support it.
Added code to check PEC capability for adapter and enable it
only if both controller and adapter supports PEC.
Signed-off-by: Madhava Reddy Siddareddygari <msiddare@cisco.com>
[Upstream from SONiC https://github.com/Azure/sonic-linux-kernel/pull/215]
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20210605052700.541455-1-pmenzel@molgen.mpg.de
[groeck: Dropped unnecessary continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
adm1272 supports temperature reporting but it is disabled by default.
Tested:
ls temp1_*
temp1_crit temp1_highest temp1_max
temp1_crit_alarm temp1_input temp1_max_alarm
cat temp1_input
26642
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20210512171043.2433694-1-linchuyuan@google.com
[groeck: Updated subject to reflect correct driver]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a digital, multi-phase, pulse-width modulation
controller.
This device supports:
- One power rail.
- Programmable Multi-Phase up to 10 Phases.
- PWM-VID Interface
- One pages 0 for telemetry.
- Programmable pins for PMBus Address.
- Built-In EEPROM to Store Custom Configurations.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210511055619.118104-3-vadimp@nvidia.com
[groeck: Add MODULE_IMPORT_NS]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Increase maximum number of phases from 8 to 10 to support multi-phase
devices allowing up to 10 phases.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210511055619.118104-2-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Flex BMR310, BMR456, BMR457, BMR458, BMR480, BMR490,
BMR491 and BMR492 to the pmbus driver
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-4-erik.rosen@metormote.com
[groeck: Fixed minor whitespace error]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips end up in an undefined state when trying to read an
unsupported register. For such chips, it is necessary to reset the
chip pmbus controller to a known state after a failed register check.
This can be done by reading a known register. By setting this flag the
driver will try to read the STATUS register after each failed
register check. This read may fail, but it will put the chip into a
known state.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-2-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Renesas ZL8802 Dual Channel/Dual Phase PMBus DC/DC
Digital Controller as well as ZLS1003 and ZLS4009 custom DC/DC
controller chips.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210423153329.33457-2-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The BPA-RS600 doesn't follow the PMBus spec for linear data.
Specifically it treats the mantissa as an unsigned 11-bit value instead
of a two's complement 11-bit value. At this point it's unclear whether
this only affects Vin or if Pin/Pout1 are affected as well. Erring on
the side of caution only Vin is dealt with here.
Fixes: 15b2703e5e ("hwmon: (pmbus) Add driver for BluTek BPA-RS600")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210616034218.25821-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PMBUS_MFR_ID block is actually 6 chars for q54sj108a2.
/sys/bus/i2c/drivers/q54sj108a2_test# iotools smbus_read8 $BUS $ADDR 0x99
0x06
Tested: Devices are able to bind to the q54sj108a2 driver successfully.
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20210517222606.3457594-1-linchuyuan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The initial version of the RAA228228 datasheet claimed that the device
supported READ_TEMPERATURE_3 but not READ_TEMPERATURE_1. It has since been
discovered that the datasheet was incorrect. The RAA228228 does support
READ_TEMPERATURE_1 but does not support READ_TEMPERATURE_3.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Fixes: 51fb91ed5a ("hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_1 telemetry for RAA228228")
Link: https://lore.kernel.org/r/20210514211954.GA24646@raspberrypi
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After testing new YH-5151E devices, we found out that not all YH-5151E
work the same. The newly tested devices actually report vout correctly
in linear16 (even though they're still YH-5151E). We suspect that it is
because these new devices have a different firmware version, but that is
unconfirmed. The version cannot be queried through PMBus.
The compliant versions of YH-5151E report VOUT_MODE normally, so we turn
on the linear11 workaround only if VOUT_MODE doesn't report anything.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210513201110.313523-1-kubernat@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I didn't properly test the driver for YH-5151E, so it was completely
broken. Firstly, the log/real mapping was incorrect in one case.
Secondly, PMBus specifies that output voltages should be in the linear16
encoding. However, the YH-5151E is non-compliant and uses linear11.
YM-2151E isn't affected by this. Fix this by converting the values
inside the read functions. linear16 gets the exponent from the VOUT_MODE
command. The device doesn't support it, so I have to manually supply the
value for it.
Both supported devices have now been tested to report correct vout
values.
Fixes: 1734b4135a ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210429075337.110502-1-kubernat@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Exported pmbus symbols are only supposed to be used from PMBus code.
Introduce PMBUS symbol namespace to prevent misuse from other code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus driver support for Maxim MAX15301 InTune Automatically
Compensated Digital PoL Controller with Driver and PMBus Telemetry
Even though the specification does not specifically mention it,
extensive empirical testing has revealed that auto-detection of
limit-registers will fail in a random fashion unless the delay
parameter is set to above about 80us. The default delay is set
to 100us to include some safety margin.
This patch is tested on a Flex BMR461 converter module.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210419101251.24840-1-erik.rosen@metormote.com
[groeck: Added rationale for delay to driver header]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Certain VRs might be configured to use only the first output channel and
so the mode for the second will be 0. Handle this gracefully.
Fixes: b9fa0a3acf ("hwmon: (pmbus/core) Add support for vid mode detection per page bases")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210416102926.13614-1-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for these devices:
- YH-5151E - the PDU
- YM-2151E - the PSU
The device datasheet says that the devices support PMBus 1.2, but in my
testing, a lot of the commands aren't supported and if they are, they
sometimes behave strangely or inconsistently. For example, writes to the
PAGE command requires using PEC, otherwise the write won't work and the
page won't switch, even though, the standard says that PEC is optional.
On the other hand, writes to SMBALERT don't require PEC. Because of
this, the driver is mostly reverse engineered with the help of a tool
called pmbus_peek written by David Brownell (and later adopted by my
colleague Jan Kundrát).
The device also has some sort of a timing issue when switching pages,
which is explained further in the code.
Because of this, the driver support is limited. It exposes only the
values that have been tested to work correctly.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210414080019.3530794-1-kubernat@cesnet.cz
[groeck: Fixed up "missing braces around initializer" from 0-day]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for TI TPS53676 controller to the tps53679 pmbus driver
The driver uses the USER_DATA_03 register to figure out how many phases
are enabled and to which channel they are assigned, and sets the number
of pages and phases accordingly.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210322193734.75127-3-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The BPA-RS600 is a compact 600W AC to DC removable power supply module.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210317040231.21490-3-chris.packham@alliedtelesis.co.nz
[groeck: Added bpa-rs600 to index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
coccicheck complains about the use of snprintf() in sysfs
show functions.
drivers/hwmon/ina3221.c:701:8-16: WARNING: use scnprintf or sprintf
This results in a large number of patch submissions. Fix it all in
one go using the following coccinelle rules. Use sysfs_emit instead
of scnprintf or sprintf since that makes more sense.
@depends on patch@
identifier show, dev, attr, buf;
@@
ssize_t show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
return
- snprintf(buf, \( PAGE_SIZE \| PAGE_SIZE - 1 \),
+ sysfs_emit(buf,
...);
...>
}
@depends on patch@
identifier show, dev, attr, buf, rc;
@@
ssize_t show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
rc =
- snprintf(buf, \( PAGE_SIZE \| PAGE_SIZE - 1 \),
+ sysfs_emit(buf,
...);
...>
}
While at it, remove unnecessary braces and as well as unnecessary
else after return statements to address checkpatch warnings in the
resulting patch.
Cc: Zihao Tang <tangzihao1@hisilicon.com>
Cc: Jay Fang <f.fangjian@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon sysfs ABI requires that the `name` property doesn't include
any dashes. But when the pmbus code picks the name up from the device
tree it quite often does. Replace '-' with '_' before registering the
device.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210317040231.21490-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hardware monitoring support for ST STPDDC60 Unversal Digital
Multicell Controller.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-3-erik.rosen@metormote.com
[groeck: Fixed whitespace error in Makefile]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For the STPDDC60 chip, the vout alarm-limits are represented as an offset
relative to the commanded output voltage. This means that the limits are
dynamic and must not be cached by the pmbus driver. This patch adds a
pmbus_set_sensor() function to pmbus_core to be able to set the update flag
on selected sensors after auto-detection of limit attributes.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-2-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There was an issue in how the tach feedbacks of dual rotor fans were
reported during any change in fan speeds with revision "A" of the
MAX31785. When the fan speeds would transition to a new target speed,
the rotor not wired to the TACH input when TACHSEL = 0 would report a
speed of 0 until the new target was reached. This has been fixed,
resulting in a revision "B" update where the MFR_REVISION of "B" is
0x3061.
Signed-off-by: Matthew Barth <msbarth@linux.ibm.com>
Link: https://lore.kernel.org/r/20210201212217.73721-1-msbarth@linux.ibm.com
[groeck: Change 'ret' variable type to int]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16508 is quite similar to MAX16601, except that it does not support
the DEFAULT_NUM_POP register and we thus can not dynamically determine
the number of populated phases.
Cc: Alex Qiu <xqiu@google.com>
Cc: Ugur Usug <Ugur.Usug@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210125185327.93282-2-linux@roeck-us.net
Reviewed-by: Alex Qiu <xqiu@google.com>
Tested-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX16601 can report the number of populated phases. Use this
information to only create sysfs attributes for populated phases.
Cc: Alex Qiu <xqiu@google.com>
Cc: Ugur Usug <Ugur.Usug@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210125185327.93282-1-linux@roeck-us.net
Reviewed-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix the following coccicheck warnings:
./drivers/hwmon/pmbus/pmbus_core.c:1265:24-26: WARNING !A || A && B is
equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Link: https://lore.kernel.org/r/1611642100-29937-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several power supplies supported by the IBM CFFPS driver don't
report valid data in the CAPABILITY register. This results in PEC
being enabled when it's not supported by the device, and since
the automatic version detection might fail, disable use of the
CAPABILITY register across the board for this driver.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20201222152640.27749-3-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips don't respond with valid data when reading the
CAPABILITY register. Add a flag that device drivers can set so
that the PMBus core driver doesn't use CAPABILITY to determine it's
behavior.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20201222152640.27749-2-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver supports Q54SJ108A2 series modules of Delta.
Standard attributes are in sysfs, and other attributes are in debugfs.
Signed-off-by: xiao.ma <xiao.mx.ma@deltaww.com>
Link: https://lore.kernel.org/r/20201202025900.1842-1-max701@126.com
[groeck: Replaced spaces with tabs, dropped excessive spaces,
fixed module prefix in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the STMicroelectronics pm6764 voltage regulator.
the output voltage use the MFR_READ_VOUT 0xD4
vout value returned is linear11
Signed-off-by: Charles Hsu <hsu.yungteng@gmail.com>
[groeck: Fixed various compile errors; marked pm6764tr_of_match __maybe_unused]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only action currently performed in pmbus_do_remove() is removing the
debugfs hierarchy. We can schedule a devm action at probe time and remove
pmbus_do_remove() entirely from all pmbus drivers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201026105352.20359-1-brgl@bgdev.pl
[groeck: Removed references to pmbus_do_remove from documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The debugfs_create_dir() function never returns NULL. Normal users are
not supposed to check the return value so the correct fix is just to
delete this check.
In the case where the debugfs_create_dir() fails, the function returns
NULL. The other debugfs function check for NULL directory and handle
it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201022070659.GA2817762@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As part of commit a919ba0697 ("hwmon: (pmbus) Stop caching register
values"), the update of the sensor value is now triggered directly by the
sensor attribute value being read from sysfs. This created (or at least
made much more likely) a locking issue, since nothing protected the device
page selection from being unexpectedly modified by concurrent reads. If
sensor values on different pages on the same device were being concurrently
read by multiple threads, this could cause spurious read errors due to the
page register not reading back the same value last written, or sensor
values being read from the incorrect page.
Add locking of the update_lock mutex in pmbus_show_sensor and
pmbus_show_samples so that these cannot result in concurrent reads from the
underlying device.
Fixes: a919ba0697 ("hwmon: (pmbus) Stop caching register values")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Alex Qiu <xqiu@google.com>
Link: https://lore.kernel.org/r/20201103193315.3011800-1-robert.hancock@calian.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The snprintf() function returns the number of characters which would
have been printed if there were enough space, but the scnprintf()
returns the number of characters which were actually printed. If the
buffer is not large enough, then using snprintf() would result in a
read overflow and an information leak.
Fixes: 8910c0bd53 ("hwmon: (pmbus/max20730) add device monitoring via debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201022070824.GC2817762@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here is the "big" set of driver core patches for 5.10-rc1
They include a lot of different things, all related to the driver core
and/or some driver logic:
- sysfs common write functions to make it easier to audit sysfs
attributes
- device connection cleanups and fixes
- devm helpers for a few functions
- NOIO allocations for when devices are being removed
- minor cleanups and fixes
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4c4yA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylS7gCfcS+7/PE42eXxMY0z8rBX8aDMadIAn2DVEghA
Eoh9UoMEW4g1uMKORA0c
=CVAW
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.10-rc1
They include a lot of different things, all related to the driver core
and/or some driver logic:
- sysfs common write functions to make it easier to audit sysfs
attributes
- device connection cleanups and fixes
- devm helpers for a few functions
- NOIO allocations for when devices are being removed
- minor cleanups and fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (31 commits)
regmap: debugfs: use semicolons rather than commas to separate statements
platform/x86: intel_pmc_core: do not create a static struct device
drivers core: node: Use a more typical macro definition style for ACCESS_ATTR
drivers core: Use sysfs_emit for shared_cpu_map_show and shared_cpu_list_show
mm: and drivers core: Convert hugetlb_report_node_meminfo to sysfs_emit
drivers core: Miscellaneous changes for sysfs_emit
drivers core: Reindent a couple uses around sysfs_emit
drivers core: Remove strcat uses around sysfs_emit and neaten
drivers core: Use sysfs_emit and sysfs_emit_at for show(device *...) functions
sysfs: Add sysfs_emit and sysfs_emit_at to format sysfs output
dyndbg: use keyword, arg varnames for query term pairs
driver core: force NOIO allocations during unplug
platform_device: switch to simpler IDA interface
driver core: platform: Document return type of more functions
Revert "driver core: Annotate dev_err_probe() with __must_check"
Revert "test_firmware: Test platform fw loading on non-EFI systems"
iio: adc: xilinx-xadc: use devm_krealloc()
hwmon: pmbus: use more devres helpers
devres: provide devm_krealloc()
syscore: Use pm_pr_dbg() for syscore_{suspend,resume}()
...
Problem:
We use voltage dividers so that the voltage presented at the voltage
sense pins is confusing. We might need to convert these readings to more
meaningful readings given the voltage divider.
Solution:
Read the voltage divider resistance from dts and convert the voltage
reading to a more meaningful reading.
Testing:
max20730 with voltage divider
Signed-off-by: Chu Lin <linchuyuan@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201004031445.2321090-3-linchuyuan@google.com
[groeck: Return -EINVAL instead of -ENODEV on bad deevicetree data]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add debugfs interface support for accessing device specific registers
(MFR_VOUT_MIN, MFR_DEVSET1 and MFR_DEVSET2) and others including
OPERATION, ON_OFF_CONFIG, SMB_ALERT_MASK, VOUT_MODE, VOUT_COMMAND
and VOUT_MAX.
Signed-off-by: Ugur Usug <ugur.usug@maximintegrated.com>
Link: https://lore.kernel.org/r/MWHPR11MB1965C01083AD013C630646B2FD3B0@MWHPR11MB1965.namprd11.prod.outlook.com
[groeck: Resolved conflics seen due to PMBus driver API changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The max34* family have the IOUT_OC_WARN_LIMIT and IOUT_OC_CRIT_LIMIT
registers swapped.
Cc: stable@vger.kernel.org
Signed-off-by: Steve Foreman <foremans@google.com>
[groeck: Updated subject, use C comment style, tab after defines]
[groeck: Added missing break; statements (by alexandru.ardelean@analog.com)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp295 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a dual-loop, digital, multi-phase controller.
This device:
- Supports two power rail.
- Provides 8 pulse-width modulations (PWMs), and can be configured up
to 8-phase operation for rail 1 and up to 4-phase operation for rail
2.
- Supports two pages 0 and 1 for telemetry and also pages 2 and 3 for
configuration.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20200926204957.10268-2-vadimp@nvidia.com
[groeck: Cleaned up a couple of error returns; fixed up API changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
0-day rightfully complains about a sometimes uninitialized variable
in pmbus_get_boolean().
drivers/hwmon/pmbus/pmbus_core.c:903:13: warning:
variable 'ret' is used uninitialized whenever 'if' condition is true
} else if (!s1 || !s2) {
While that is technically true, it won't be hit in the field since the
condition indicates a programming error. Move the check of that condition
into the code generating the attribute entry, and refuse generating the
attribute if the condition is true. Swap the condition check in
pmbus_get_boolean() to ensure that static analyzers don't get a hiccup
(because we check if s1 and s2 are NULL, static analyzers may believe
that they can be NULL independently of each other).
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alex Qiu <xqiu@google.com>
Reviewed-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enable runtime debug control of whether the PEC byte is exchanged with
the PMBus device.
Some manufacturers have asked for the PEC to be disabled as part of
debugging driver communication issues with devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200910021106.2958382-1-andrew@aj.id.au
[groeck: Replace %1llu with %llu]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Caching register values can be very expensive for PMBus chips. Some
modern chips may have 10 or more pages, with several sensors supported
per page. For example, MAX16601 creates more than 90 sysfs attributes.
Register caching for such chips is time consuming, especially if only a
few attributes are read on a regular basis. For MAX16601, it was observed
that it can take up to two seconds to read all attributes on a slow I2C
bus. In this situation, register caching results in the opposite of its
intention: It increases the number of I2C operations, in some cases
substantially, and it results in large latency when trying to access
individual sensor data.
Drop all register caching to solve the problem. Since it is no longer
necessary, drop status register mapping as part of the change, and specify
status registers directly.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alex Qiu <xqiu@google.com>
Tested-by: Alex Qiu <xqiu@google.com>
Link: https://lore.kernel.org/r/20200904163314.259087-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the nvmem kernel api to expose the black box
chip functionality to userspace.
Using this feature, the device is capable of recording
to nonvolatile flash memory the vital data about the
system status that caused the system to perform a
black box write.
A blackbox is 64 bytes of data containing all the
status registers, last two states of the sequencer,
timestamp and counters. The mapping of this data is
described in the adm1266 datasheet.
On power-up the driver sets the unix time to
the adm1266 using the SET_RTC command. This value
is incremented by an internal clock and it is used
as timestamp for the black box feature.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-6-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adm1266 exposes 9 GPIOs and 16 PDIOs which are currently read-only. They
are controlled by the internal sequencing engine.
This patch makes adm1266 driver expose GPIOs and PDIOs to user-space
using GPIO provider kernel api.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-4-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PmBus devices support Block Write-Block Read Process
Call described in SMBus specification v 2.0 with the
exception that Block writes and reads are permitted to
have up 255 data bytes instead of max 32 bytes (SMBus).
This patch adds Block WR process call support for ADM1266.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-3-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-2-alexandru.tachici@analog.com
[groeck: Use .probe_new function, adjust for changed pmbus_do_probe API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding implementation for new attributes (rated_min/rated_max) to
cover PMBus specification about rated values reporting:
MFR_VIN_MIN, MFR_VIN_MAX, MFR_IIN_MAX, MFR_PIN_MAX, MFR_VOUT_MIN,
MFR_VOUT_MAX, MFR_IOUT_MAX, MFR_POUT_MAX, MFR_MAX_TEMP_1/2/3.
Tested with OpenBMC stack. All rated attributes were available
and reported correct values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-4-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Starting with MAX34451, the chips of this series support STATUS_IOUT and
STATUS_TEMPERATURE commands, and no longer report over-current and
over-temperature status with STATUS_MFR_SPECIFIC.
Fixes: 7a001dbab4 ("hwmon: (pmbus/max34440) Add support for MAX34451.")
Fixes: 50115ac9b6 ("hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461")
Reported-by: Steve Foreman <foremans@google.com>
Cc: Steve Foreman <foremans@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per the RAA228228 datasheet, READ_TEMPERATURE_1 is not a supported PMBus
command.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using s64 type, instead of long type, for internal calculations and for
the sysfs interface.
This allows 64-bit values to appear correctly on 32-bit kernels.
As wattage is reported in microwatts, monitoring a power supply over
2KW requires this.
Although it may seem unlikely to run a 32-bit kernel on such a large
machine, enterprise servers often include a BMC, and the BMC might be
running a 32-bit kernel.
Signed-off-by: Josh Lehan <krellan@google.com>
[groeck: Removed Change-Id and other tags, reformatted description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adm1278 temp attribute need it for openbmc platform .
This feature not enabled by default, so PMON_CONFIG needs to enable it.
Signed-off-by: Manikandan Elumalai <manikandan.hcl.ers.epl@gmail.com>
Link: https://lore.kernel.org/r/20200622153727.GA9347@cnn
[groeck: Split long line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Issue:
When PEC is enabled, binding adm1272 to the adm1275 would
fail due to PEC error. See below:
adm1275: probe of xxxx failed with error -74
Diagnosis:
Per the datasheet of adm1272, adm1278, adm1293 and amd1294,
PMON_CONFIG (0xd4) is 16bits wide. On the other hand,
PMON_CONFIG (0xd4) for adm1275 is 8bits wide. The driver should not
assume everything is 8bits wide and read only 8bits from it.
Solution:
If it is adm1272, adm1278, adm1293 and adm1294, use i2c_read_word.
Else, use i2c_read_byte
Testing:
Binding adm1272 to the driver.
The change is only tested on adm1272.
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20200709040612.3977094-1-linchuyuan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix a typo in SENSORS_IR35221 option: module name should be "ir35221"
instead of "ir35521".
Fixes: 8991ebd9c9 ("hwmon: (pmbus) Add client driver for IR35221")
Cc: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200702221349.18139-1-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 16358542f3 ("hwmon: (pmbus) Implement multi-phase support")
added support for multi-phase pmbus devices. However, when calling
pmbus_add_sensor() for fans, the patch swapped the `page` and `reg`
attributes. As a result, the fan speeds were reported as 0 RPM on my device.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Fixes: 16358542f3 ("hwmon: (pmbus) Implement multi-phase support")
Cc: stable@vger.kernel.org # v5.7+
Link: https://lore.kernel.org/r/449bc9e6c0e4305581e45905ce9d043b356a9932.1592904387.git.jan.kundrat@cesnet.cz
[groeck: Fixed references to offending commit]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16601 is a VR13.HC Dual-Output Voltage Regulator Chipset,
implementing a (8+1) multiphase synchronous buck converter.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'currpage' and 'currphase' variables in struct pmbus_data are used by
the PMBus core to determine if the phase or page value has changed. Both
are initialized with values which are never expected to be set in the code
to ensure that the first page/phase write operation is actually performed.
This is not well explained and occasionally causes confusion. Change the
type of both variables to s16 and initialize with -1 to ensure that the
initial value never matches a requested value, and clarify that this
value means "unknown/unset".
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C chip IDs need to reflect chip names, not chip functionality.
Fixes: f621d61fd5 ("hwmon: (pmbus) add support for 2nd Gen Renesas digital multiphase")
Cc: Grant Peltier <grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is an additional CCIN for the IBM CFFPS that may be classifed as
either version one or version two, based upon the rest of the bits of
the CCIN. Add support for it in the version detection.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1583948590-17220-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TPS53647 and TPS53667 are single channel, Step-Down Buck Controllers.
TPS53647 supports 4 phases, TPS53667 supports 6 phases.
The chips do not support per-phase output telemetry.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips of this series with published datasheets support IIN, PIN, and
STATUS_INPUT PMBus commands. Per TI Power Management Forum, "TPS53679 and
TPS53681 have the same PMBus command set". There is no reason to believe
that this does not apply to TPS53688. Let's assume that this is correct
and add support for IIN, PIN, and STATUS_INPUT to TPS53679 and TPS53688
to simplify adding support for more chips of the same series.
At the same time, drop reporting VIN on channel 2. On chips with published
datasheets this voltage is identical to the voltage reported on channel 1,
and there is no reason to believe that this is different for TPS53679 and
TPS53888.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Chip specific support will be needed in the driver to be able to
support additional chips of the same series. Add support for it
to the driver.
To simplify adding support for more chips, call identification code
from the probe function. This lets us use a single structure for common
elements of struct pmbus_driver_info, thus reducing code size as support
for more chips is added.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips support multiple phases, and report telemetry such
as input current, output current, or temperature for each phase.
Add support for such chips to the PMBus core.
Start with a maximum of 8 phases per page, and assume that supported
sensors per phase are similar for all pages. Only support per-phase
telemetry attributes, no limits or alarms.
As part of this patch, set the initial page variable to 0xff to ensure
that the page is updated when the first page command is issued. Also
only issue page commands if the chip supports more than one page.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation for multi-phase support, add 'phase' parameter to read_word
and set_page functions. Actual multi-phase support will be added in
a subsequent patch.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Recent PMBus versions added IC_DEVICE_ID and IC_DEVICE_REV commands as
additional means to identify the chip. Add command definitions to
pmbus.h include file.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Provide read_word_data() callback for overvoltage and undervoltage
output readouts conversion. These registers are presented in
'slinear11' format, while default conversion for 'vout' class for the
devices is 'vid'. It is resulted in wrong conversion in pmbus_reg2data()
for in{3-4}_lcrit and in{3-4}_crit attributes.
)
Fixes: aaafb7c8eb ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200224225202.19576-1-vadimp@mellanox.com
[gropeck: Adjusted to mainline PMBus API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make sure that the driver compatible strings matches the binding by
removing the space between the manufacturer and model.
Fixes: aaafb7c8eb ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers")
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200212092426.24012-1-johan@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.
Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com
Fixes: e04d1ce9bb ("hwmon: (ltc2978) Add polling for chips requiring it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
