linux-yocto/drivers/usb/Kconfig

USB device configuration

config USB_OHCI_BIG_ENDIAN_DESC bool

config USB_OHCI_BIG_ENDIAN_MMIO bool

config USB_OHCI_LITTLE_ENDIAN bool default n if STB03xxx || PPC_MPC52xx default y

config USB_EHCI_BIG_ENDIAN_MMIO bool

config USB_EHCI_BIG_ENDIAN_DESC bool

menuconfig USB_SUPPORT bool "USB support" depends on HAS_IOMEM default y ---help--- This option adds core support for Universal Serial Bus (USB). You will also need drivers from the following menu to make use of it.

if USB_SUPPORT

config USB_COMMON tristate

config USB_ARCH_HAS_HCD def_bool y

config USB tristate "Support for Host-side USB" depends on USB_ARCH_HAS_HCD select USB_COMMON select NLS # for UTF-8 strings ---help--- Universal Serial Bus (USB) is a specification for a serial bus subsystem which offers higher speeds and more features than the traditional PC serial port. The bus supplies power to peripherals and allows for hot swapping. Up to 127 USB peripherals can be connected to a single USB host in a tree structure.

  The USB host is the root of the tree, the peripherals are the
  leaves and the inner nodes are special USB devices called hubs.
  Most PCs now have USB host ports, used to connect peripherals
  such as scanners, keyboards, mice, modems, cameras, disks,
  flash memory, network links, and printers to the PC.

  Say Y here if your computer has a host-side USB port and you want
  to use USB devices.  You then need to say Y to at least one of the
  Host Controller Driver (HCD) options below.  Choose a USB 1.1
  controller, such as "UHCI HCD support" or "OHCI HCD support",
  and "EHCI HCD (USB 2.0) support" except for older systems that
  do not have USB 2.0 support.  It doesn't normally hurt to select
  them all if you are not certain.

  If your system has a device-side USB port, used in the peripheral
  side of the USB protocol, see the "USB Gadget" framework instead.

  After choosing your HCD, then select drivers for the USB peripherals
  you'll be using.  You may want to check out the information provided
  in <file:Documentation/usb/> and especially the links given in
  <file:Documentation/usb/usb-help.txt>.

  To compile this driver as a module, choose M here: the
  module will be called usbcore.

config USB_PCI bool "PCI based USB host interface" depends on PCI default y ---help--- A lot of embeded system SOC (e.g. freescale T2080) have both PCI and USB modules. But USB module is controlled by registers directly, it have no relationship with PCI module.

  When say N here it will not build PCI related code in USB driver.

if USB

source "drivers/usb/core/Kconfig"

source "drivers/usb/mon/Kconfig"

source "drivers/usb/wusbcore/Kconfig"

source "drivers/usb/host/Kconfig"

source "drivers/usb/renesas_usbhs/Kconfig"

source "drivers/usb/class/Kconfig"

source "drivers/usb/storage/Kconfig"

source "drivers/usb/image/Kconfig"

source "drivers/usb/usbip/Kconfig"

endif

source "drivers/usb/mtu3/Kconfig"

source "drivers/usb/musb/Kconfig"

source "drivers/usb/dwc3/Kconfig"

source "drivers/usb/dwc2/Kconfig"

source "drivers/usb/chipidea/Kconfig"

source "drivers/usb/isp1760/Kconfig"

comment "USB port drivers"

if USB

config USB_USS720 tristate "USS720 parport driver" depends on PARPORT select PARPORT_NOT_PC ---help--- This driver is for USB parallel port adapters that use the Lucent Technologies USS-720 chip. These cables are plugged into your USB port and provide USB compatibility to peripherals designed with parallel port interfaces.

  The chip has two modes: automatic mode and manual mode. In automatic
  mode, it looks to the computer like a standard USB printer. Only
  printers may be connected to the USS-720 in this mode. The generic
  USB printer driver ("USB Printer support", above) may be used in
  that mode, and you can say N here if you want to use the chip only
  in this mode.

  Manual mode is not limited to printers, any parallel port
  device should work. This driver utilizes manual mode.
  Note however that some operations are three orders of magnitude
  slower than on a PCI/ISA Parallel Port, so timing critical
  applications might not work.

  Say Y here if you own an USS-720 USB->Parport cable and intend to
  connect anything other than a printer to it.

  To compile this driver as a module, choose M here: the
  module will be called uss720.

source "drivers/usb/serial/Kconfig"

source "drivers/usb/misc/Kconfig"

source "drivers/usb/atm/Kconfig"

endif # USB

source "drivers/usb/phy/Kconfig"

source "drivers/usb/gadget/Kconfig"

source "drivers/usb/typec/Kconfig"

config USB_LED_TRIG bool "USB LED Triggers" depends on LEDS_CLASS && LEDS_TRIGGERS select USB_COMMON help This option adds LED triggers for USB host and/or gadget activity.

  Say Y here if you are working on a system with led-class supported
  LEDs and you want to use them as activity indicators for USB host or
  gadget.

config USB_ULPI_BUS tristate "USB ULPI PHY interface support" select USB_COMMON help UTMI+ Low Pin Interface (ULPI) is specification for a commonly used USB 2.0 PHY interface. The ULPI specification defines a standard set of registers that can be used to detect the vendor and product which allows ULPI to be handled as a bus. This module is the driver for that bus.

  The ULPI interfaces (the buses) are registered by the drivers for USB
  controllers which support ULPI register access and have ULPI PHY
  attached to them. The ULPI PHY drivers themselves are normal PHY
  drivers.

  ULPI PHYs provide often functions such as ADP sensing/probing (OTG
  protocol) and USB charger detection.

  To compile this driver as a module, choose M here: the module will
  be called ulpi.

endif # USB_SUPPORT