The IMX91_CLK_SPDIF_GATE also controls the gate of IPG clock
and root clock, need to define them separately.
Otherwise disabling IMX91_CLK_SPDIF_GATE in driver will cause
IPG clock is disabled, then register accessing fail.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
The IMX93_CLK_SPDIF_GATE also controls the gate of IPG clock
and root clock, need to define them separately.
Otherwise driver disable IMX93_CLK_SPDIF_GATE will cause
IPG clock is also disabled, then register accessing fail.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
The scu clk_ops only inplements prepare() and unprepare() callback.
Saving the clock state during suspend by checking clk_hw_is_enabled()
is not safe as it's possible that some buggy device drivers may only
disable the clocks without unprepare. Then the state retention become
unwork for such clocks.
Fixing it by checking clk_hw_is_prepared() which is more reasonable
and safe.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
(cherry picked from commit c6630b8248eba8e8ccf1fcf35bf800bb74680c3b)
current PLL power up flow can be simplified as below:
1. writel to set the PLL POWERUP bit;
2. readl_poll_timeout to check the PLL lock bit:
a). timeout = ktime_add_us(ktime_get(), timeout_us);
b). readl the pll the lock reg;
c). check if the pll lock bit ready
d). check if timeout
But in some corner case, both the writel in step 1 and readl in
step 2 will be blocked by other bus transaction in the SoC for a
long time, then may have chance that the pll lock bit is not ready
when readl done but the timeout happens. readl_poll_timeout will
err return due to timeout. To avoid such unexpected failure,
we can read back the 'POWERUP' control reg to make sure the writel
has been done in HW reg before we can read the PLL lock bit to
check the PLL lock status.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
[ Upstream commit 7b6dfa1bbe ]
Amit Pundir reports that audio and USB-C host mode stops working if the
gcc_usb30_prim_master_clk_src clk is registered and
clk_rcg2_shared_init() parks it on XO. Skip parking this clk at
registration time to fix those issues.
Partially revert commit 01a0a6cc8c ("clk: qcom: Park shared RCGs upon
registration") by skipping the parking bit for this clk, but keep the
part where we cache the config register. That's still necessary to
figure out the true parent of the clk at registration time.
Fixes: 01a0a6cc8c ("clk: qcom: Park shared RCGs upon registration")
Fixes: 929c75d575 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable")
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/CAMi1Hd1KQBE4kKUdAn8E5FV+BiKzuv+8FoyWQrrTHPDoYTuhgA@mail.gmail.com
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240819233628.2074654-3-swboyd@chromium.org
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d10eeb7516 ]
The QUPs aren't shared in a way that requires parking the RCG at an
always on parent in case some other entity turns on the clk. The
hardware is capable of setting a new frequency itself with the DFS mode,
so parking is unnecessary. Furthermore, there aren't any GDSCs for these
devices, so there isn't a possibility of the GDSC turning on the clks
for housekeeping purposes.
This wasn't a problem to mark these clks shared until we started parking
shared RCGs at clk registration time in commit 01a0a6cc8c ("clk: qcom:
Park shared RCGs upon registration"). Parking at init is actually
harmful to the UART when earlycon is used. If the device is pumping out
data while the frequency changes you'll see garbage on the serial
console until the driver can probe and actually set a proper frequency.
Revert the QUP part of commit 929c75d575 ("clk: qcom: gcc-sm8550: Mark
RCGs shared where applicable") so that the QUPs don't get parked during
clk registration and break UART operations.
Fixes: 01a0a6cc8c ("clk: qcom: Park shared RCGs upon registration")
Fixes: 929c75d575 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable")
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/CAMi1Hd1KQBE4kKUdAn8E5FV+BiKzuv+8FoyWQrrTHPDoYTuhgA@mail.gmail.com
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240819233628.2074654-2-swboyd@chromium.org
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6357efe3ab ]
Update PLL offsets to DEFAULT_EVO to configure MDIO to 800MHz.
The incorrect clock frequency leads to an incorrect MDIO clock. This,
in turn, affects the MDIO hardware configurations as the divider is
calculated from the MDIO clock frequency. If the clock frequency is
not as expected, the MDIO register fails due to the generation of an
incorrect MDIO frequency.
This issue is critical as it results in incorrect MDIO configurations
and ultimately leads to the MDIO function not working. This results in
a complete feature failure affecting all Ethernet PHYs. Specifically,
Ethernet will not work on IPQ9574 due to this issue.
Currently, the clock frequency is set to CLK_ALPHA_PLL_TYPE_DEFAULT.
However, this setting does not yield the expected clock frequency.
To rectify this, we need to change this to CLK_ALPHA_PLL_TYPE_DEFAULT_EVO.
This modification ensures that the clock frequency aligns with our
expectations, thereby resolving the MDIO register failure and ensuring
the proper functioning of the Ethernet on IPQ9574.
Fixes: d75b82cff4 ("clk: qcom: Add Global Clock Controller driver for IPQ9574")
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Amandeep Singh <quic_amansing@quicinc.com>
Link: https://lore.kernel.org/r/20240806061105.2849944-1-quic_amansing@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4ad1ed6ef2 upstream.
Correct the pll postdiv shift used in clk_trion_pll_postdiv_set_rate
API. The shift value is not same for different types of plls and
should be taken from the pll's .post_div_shift member.
Fixes: 548a909597 ("clk: qcom: clk-alpha-pll: Add support for Trion PLLs")
Cc: stable@vger.kernel.org
Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240731062916.2680823-3-quic_skakitap@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c4553e6c4 upstream.
The PLL_POST_DIV_MASK should be 0 to (width - 1) bits. Fix it.
Fixes: 1c3541145c ("clk: qcom: support for 2 bit PLL post divider")
Cc: stable@vger.kernel.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Link: https://lore.kernel.org/r/20240731062916.2680823-2-quic_skakitap@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 538d5477b2 upstream.
Add notifier function for PLL0 clock. In the function, the cpu_root clock
should be operated by saving its current parent and setting a new safe
parent (osc clock) before setting the PLL0 clock rate. After setting PLL0
rate, it should be switched back to the original parent clock.
Fixes: e2c510d6d6 ("riscv: dts: starfive: Add cpu scaling for JH7110 SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Link: https://lore.kernel.org/r/20240826080430.179788-2-xingyu.wu@starfivetech.com
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Tested-by: Michael Jeanson <mjeanson@efficios.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 397d887c16 ]
In order to gain the bounds-checking coverage that __counted_by provides
to flexible-array members at run-time via CONFIG_UBSAN_BOUNDS (for array
indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family functions),
we must make sure that the counter member, in this particular case `num`,
is updated before the first access to the flex-array member, in this
particular case array `hws`. See below:
commit f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with
__counted_by") introduced `__counted_by` for `struct clk_hw_onecell_data`
together with changes to relocate some of assignments of counter `num`
before `hws` is accessed:
include/linux/clk-provider.h:
1380 struct clk_hw_onecell_data {
1381 unsigned int num;
1382 struct clk_hw *hws[] __counted_by(num);
1383 };
However, this structure is used as a member in other structs, in this
case in `struct visconti_pll_provider`:
drivers/clk/visconti/pll.h:
16 struct visconti_pll_provider {
17 void __iomem *reg_base;
18 struct device_node *node;
19
20 /* Must be last */
21 struct clk_hw_onecell_data clk_data;
22 };
Hence, we need to move the assignments to `ctx->clk_data.num` after
allocation for `struct visconti_pll_provider` and before accessing the
flexible array `ctx->clk_data.hws`. And, as assignments for all members
in `struct visconti_pll_provider` are originally adjacent to each other,
relocate all assignments together, so we don't split up
`ctx->clk_data.hws = nr_plls` from the rest. :)
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/e3189f3e40e8723b6d794fb2260e2e9ab6b960bd.1697492890.git.gustavoars@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
CREF_EN (Bit6) of LFAST_IO_REG control PCIe REF clock enable/disable.
Add compatible string "fsl,imx95-hsio-blk-ctrl" to support PCIe REF clock gate.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
commit a83b22754e upstream.
The flag attribute of the struct clk_init_data isn't initialized before
the devm_clk_hw_register() call. This can lead to unexpected behavior
during registration.
Initialize the entire clk_init_data to zero at declaration.
Cc: stable@vger.kernel.org
Fixes: 58e1e2d2cd ("clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks")
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20240718115534.41513-1-bastien.curutchet@bootlin.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 58c53d4314 ]
Introduce div_offset field in en_clk_desc struct in order to fix rate
divider estimation in en7523_get_div routine for slic and spi fixed
rate clocks.
Moreover, fix base_shift for crypto clock.
Fixes: 1e62731791 ("clk: en7523: Add clock driver for Airoha EN7523 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c491bdea05d847f1f1294b94f14725d292eb95d0.1718615934.git.lorenzo@kernel.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01a0a6cc8c ]
There's two problems with shared RCGs.
The first problem is that they incorrectly report the parent after
commit 703db1f5da ("clk: qcom: rcg2: Cache CFG register updates for
parked RCGs"). That's because the cached CFG register value needs to be
populated when the clk is registered. clk_rcg2_shared_enable() writes
the cached CFG register value 'parked_cfg'. This value is initially zero
due to static initializers. If a driver calls clk_enable() before
setting a rate or parent, it will set the parent to '0' which is
(almost?) always XO, and may not reflect the parent at registration. In
the worst case, this switches the RCG from sourcing a fast PLL to the
slow crystal speed.
The second problem is that the force enable bit isn't cleared. The force
enable bit is only used during parking and unparking of shared RCGs.
Otherwise it shouldn't be set because it keeps the RCG enabled even when
all the branches on the output of the RCG are disabled (the hardware has
a feedback mechanism so that any child branches keep the RCG enabled
when the branch enable bit is set). This problem wastes power if the clk
is unused, and is harmful in the case that the clk framework disables
the parent of the force enabled RCG. In the latter case, the GDSC the
shared RCG is associated with will get wedged if the RCG's source clk is
disabled and the GDSC tries to enable the RCG to do "housekeeping" while
powering on.
Both of these problems combined with incorrect runtime PM usage in the
display driver lead to a black screen on Qualcomm sc7180 Trogdor
chromebooks. What happens is that the bootloader leaves the
'disp_cc_mdss_rot_clk' enabled and the 'disp_cc_mdss_rot_clk_src' force
enabled and parented to 'disp_cc_pll0'. The mdss driver probes and
runtime suspends, disabling the mdss_gdsc which uses the
'disp_cc_mdss_rot_clk_src' for "housekeeping". The
'disp_cc_mdss_rot_clk' is disabled during late init because the clk is
unused, but the parent 'disp_cc_mdss_rot_clk_src' is still force enabled
because the force enable bit was never cleared. Then 'disp_cc_pll0' is
disabled because it is also unused. That's because the clk framework
believes the parent of the RCG is XO when it isn't. A child device of
the mdss device (e.g. DSI) runtime resumes mdss which powers on the
mdss_gdsc. This wedges the GDSC because 'disp_cc_mdss_rot_clk_src' is
parented to 'disp_cc_pll0' and that PLL is off. With the GDSC wedged,
mdss_runtime_resume() tries to enable 'disp_cc_mdss_mdp_clk' but it
can't because the GDSC has wedged all the clks associated with the GDSC
causing clks to stay stuck off.
This leads to the following warning seen at boot and a black screen
because the display driver fails to probe.
disp_cc_mdss_mdp_clk status stuck at 'off'
WARNING: CPU: 1 PID: 81 at drivers/clk/qcom/clk-branch.c:87 clk_branch_toggle+0x114/0x168
Modules linked in:
CPU: 1 PID: 81 Comm: kworker/u16:4 Not tainted 6.7.0-g0dd3ee311255 #1 f5757d475795053fd2ad52247a070cd50dd046f2
Hardware name: Google Lazor (rev1 - 2) with LTE (DT)
Workqueue: events_unbound deferred_probe_work_func
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : clk_branch_toggle+0x114/0x168
lr : clk_branch_toggle+0x110/0x168
sp : ffffffc08084b670
pmr_save: 00000060
x29: ffffffc08084b680 x28: ffffff808006de00 x27: 0000000000000001
x26: ffffff8080dbd4f4 x25: 0000000000000000 x24: 0000000000000000
x23: 0000000000000000 x22: ffffffd838461198 x21: ffffffd838007997
x20: ffffffd837541d5c x19: 0000000000000001 x18: 0000000000000004
x17: 0000000000000000 x16: 0000000000000010 x15: ffffffd837070fac
x14: 0000000000000003 x13: 0000000000000004 x12: 0000000000000001
x11: c0000000ffffdfff x10: ffffffd838347aa0 x9 : 08dadf92e516c000
x8 : 08dadf92e516c000 x7 : 0000000000000000 x6 : 0000000000000027
x5 : ffffffd8385a61f2 x4 : 0000000000000000 x3 : ffffffc08084b398
x2 : ffffffc08084b3a0 x1 : 00000000ffffdfff x0 : 00000000fffffff0
Call trace:
clk_branch_toggle+0x114/0x168
clk_branch2_enable+0x24/0x30
clk_core_enable+0x5c/0x1c8
clk_enable+0x38/0x58
clk_bulk_enable+0x40/0xb0
mdss_runtime_resume+0x68/0x258
pm_generic_runtime_resume+0x30/0x44
__genpd_runtime_resume+0x30/0x80
genpd_runtime_resume+0x124/0x214
__rpm_callback+0x7c/0x15c
rpm_callback+0x30/0x88
rpm_resume+0x390/0x4d8
rpm_resume+0x43c/0x4d8
__pm_runtime_resume+0x54/0x98
__device_attach+0xe0/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x48/0xa4
device_add+0x52c/0x6fc
mipi_dsi_device_register_full+0x104/0x1a8
devm_mipi_dsi_device_register_full+0x28/0x78
ti_sn_bridge_probe+0x1dc/0x2bc
auxiliary_bus_probe+0x4c/0x94
really_probe+0xf8/0x270
__driver_probe_device+0xa8/0x130
driver_probe_device+0x44/0x104
__device_attach_driver+0xa4/0xcc
bus_for_each_drv+0x94/0xe8
__device_attach+0xf8/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x48/0xa4
deferred_probe_work_func+0x9c/0xd8
Fix these problems by parking shared RCGs at boot. This will properly
initialize the parked_cfg struct member so that the parent is reported
properly and ensure that the clk won't get stuck on or off because the
RCG is parented to the safe source (XO).
Fixes: 703db1f5da ("clk: qcom: rcg2: Cache CFG register updates for parked RCGs")
Reported-by: Stephen Boyd <sboyd@kernel.org>
Closes: https://lore.kernel.org/r/1290a5a0f7f584fcce722eeb2a1fd898.sboyd@kernel.org
Closes: https://issuetracker.google.com/319956935
Reported-by: Laura Nao <laura.nao@collabora.com>
Closes: https://lore.kernel.org/r/20231218091806.7155-1-laura.nao@collabora.com
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240502224703.103150-1-swboyd@chromium.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9db4585eca ]
Return of_clk_add_hw_provider() in order to transfer the error if it
fails.
Fixes: 09be1a39e6 ("clk: qcom: kpss-xcc: register it as clk provider")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240704073606.1976936-1-nichen@iscas.ac.cn
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 211681998d ]
Update wait_val fields as per the default hardware values of the GDSC as
otherwise it would lead to GDSC FSM state stuck causing power on/off
failures of the GSDC.
Fixes: 0afa16afc3 ("clk: qcom: add the GPUCC driver for sa8775p")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240612-sa8775p-v2-gcc-gpucc-fixes-v2-6-adcc756a23df@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff68b2f74 ]
The RCG's clk src has to be parked at XO while disabling as per the
HW recommendation, hence use clk_rcg2_shared_ops to achieve the same.
Also gpu_cc_cb_clk is recommended to be kept always ON, hence use
clk_branch2_aon_ops to keep the clock always ON.
Fixes: 0afa16afc3 ("clk: qcom: add the GPUCC driver for sa8775p")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240612-sa8775p-v2-gcc-gpucc-fixes-v2-5-adcc756a23df@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e69386d4a4 ]
The GPU clocks/GDSCs have been marked critical from the clock driver
but the GPU driver votes on these resources as per the HW requirement.
In the case where these clocks & GDSCs are left enabled, would have
power impact and also cause GPU stability/corruptions.
Fix the same by removing the CLK_IS_CRITICAL for clocks and ALWAYS_ON
flags for the GPU GDSCs.
Fixes: 0afa16afc3 ("clk: qcom: add the GPUCC driver for sa8775p")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240612-sa8775p-v2-gcc-gpucc-fixes-v2-4-adcc756a23df@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be208c0ccf ]
Update the GDSC wait_val fields as per the default hardware values as
otherwise they would lead to GDSC FSM state to be stuck and causing
failures to power on/off. Also add the GDSC flags as applicable and
add support to control PCIE GDSC's using collapse vote registers.
Fixes: 08c51ceb12 ("clk: qcom: add the GCC driver for sa8775p")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240612-sa8775p-v2-gcc-gpucc-fixes-v2-2-adcc756a23df@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 313e290902 ]
The RCG's clk src has to be parked at XO while disabling as per the
HW recommendation, hence use clk_rcg2_shared_ops to achieve the same.
Fixes: 160758b05a ("clk: qcom: add support for SM8350 GPUCC")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Link: https://lore.kernel.org/r/20240621-sm8350-gpucc-fixes-v1-1-22db60c7c5d3@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63aec3e4d9 ]
Camera titan top GDSC is a parent supply to all other camera GDSCs. Titan
top GDSC is required to be enabled before enabling any other camera GDSCs
and it should be disabled only after all other camera GDSCs are disabled.
Ensure this behavior by marking titan top GDSC as parent of all other
camera GDSCs.
Fixes: 1daec8cfeb ("clk: qcom: camcc: Add camera clock controller driver for SC7280")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240531095142.9688-4-quic_tdas@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f38467b5a9 ]
Update the force mem core bit for UFS ICE clock to force the core on signal
to remain active during halt state of the clk. When retention bit of the
clock is set the memories of the subsystem will retain the logic across
power states.
Fixes: a3cc092196 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7280")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240531095142.9688-3-quic_tdas@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Some clks maybe default enabled by hardware, so add is_prepared hook
to get the status of the clk. Then when disabling unused clks, those
unused clks but default hardware on clks could be in off state to save
power.
Reviewed-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Tested-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[ Upstream commit 878e845d8d ]
Commit 2f7b1d8b55 ("clk: mediatek: Do a runtime PM get on controllers
during probe") enabled runtime PM for all mediatek clock controllers,
but this introduced an issue on the resume path.
If a device resumes earlier than the clock controller and calls
clk_prepare() when runtime PM is enabled on the controller, it will end
up calling clk_pm_runtime_get(). But the subsequent
pm_runtime_resume_and_get() call will fail because the runtime PM is
temporarily disabled during suspend.
To workaround this, introduce a need_runtime_pm flag and only enable it
on mt8183-mfgcfg, which is the driver that observed deadlock previously.
Hopefully mt8183-cfgcfg won't run into the issue at the resume stage
because the GPU should have stopped rendering before the system calls
suspend.
Fixes: 2f7b1d8b55 ("clk: mediatek: Do a runtime PM get on controllers during probe")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240613120357.1043342-1-treapking@chromium.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a33a64524 ]
The clk_alpha_pll_stromer_plus_set_rate() function does not
sets the ALPHA_EN bit in the USER_CTL register, so setting
rates which requires using alpha mode works only if the bit
gets set already prior calling the function.
Extend the function to set the ALPHA_EN bit in order to allow
using fractional rates regardless whether the bit gets set
previously or not.
Fixes: 84da48921a ("clk: qcom: clk-alpha-pll: introduce stromer plus ops")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240508-stromer-plus-alpha-en-v1-1-6639ce01ca5b@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3414f41a13 ]
Both gpll6 and gpll7 are parented to CXO at 19.2 MHz and not to GPLL0
which runs at 600 MHz. Also gpll6_out_even should have the parent gpll6
and not gpll0.
Adjust the parents of these clocks to make Linux report the correct rate
and not absurd numbers like gpll7 at ~25 GHz or gpll6 at 24 GHz.
Corrected rates are the following:
gpll7 807999902 Hz
gpll6 768000000 Hz
gpll6_out_even 384000000 Hz
gpll0 600000000 Hz
gpll0_out_odd 200000000 Hz
gpll0_out_even 300000000 Hz
And because gpll6 is the parent of gcc_sdcc2_apps_clk_src (at 202 MHz)
that clock also reports the correct rate now and avoids this warning:
[ 5.984062] mmc0: Card appears overclocked; req 202000000 Hz, actual 6312499237 Hz
Fixes: 131abae905 ("clk: qcom: Add SM6350 GCC driver")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240508-sm6350-gpll-fix-v1-1-e4ea34284a6d@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ea977d7425 upstream.
In order to set the rate range of a hw sunxi_ccu_probe calls
hw_to_ccu_common() assuming all entries in desc->ccu_clks are contained
in a ccu_common struct. This assumption is incorrect and, in
consequence, causes invalid pointer de-references.
Remove the faulty call. Instead, add one more loop that iterates over
the ccu_clks and sets the rate range, if required.
Fixes: b914ec33b3 ("clk: sunxi-ng: common: Support minimum and maximum rate")
Reported-by: Robert J. Pafford <pafford.9@buckeyemail.osu.edu>
Closes: https://lore.kernel.org/lkml/DM6PR01MB58047C810DDD5D0AE397CADFF7C22@DM6PR01MB5804.prod.exchangelabs.com/
Cc: stable@vger.kernel.org
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Tested-by: Robert J. Pafford <pafford.9@buckeyemail.osu.edu>
Link: https://lore.kernel.org/r/20240623-sunxi-ng_fix_common_probe-v1-1-7c97e32824a1@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72ceafb587 upstream.
The crypto_ahb and crypto_axi clks are hardware voteable.
This means that the halt bit isn't reliable because some
other voter in the system, e.g. TrustZone, could be keeping
the clk enabled when the kernel turns it off from clk_disable().
Make these clks use voting mode by changing the halt check to
BRANCH_HALT_VOTED and toggle the voting bit in the voting register
instead of directly controlling the branch by writing to the branch
register. This fixes stuck clk warnings seen on ipq9574 and saves
power by actually turning the clk off.
Also changes the CRYPTO_AHB_CLK_ENA & CRYPTO_AXI_CLK_ENA
offset to 0xb004 from 0x16014.
Cc: stable@vger.kernel.org
Fixes: f6b2bd9cb2 ("clk: qcom: gcc-ipq9574: Enable crypto clocks")
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://lore.kernel.org/r/20240509105405.1262369-1-quic_mdalam@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=H63O
-----END PGP SIGNATURE-----
Merge tag 'v6.6.35' into lf-6.6.y
This is the 6.6.35 stable release
* tag 'v6.6.35': (268 commits)
Linux 6.6.35
zap_pid_ns_processes: clear TIF_NOTIFY_SIGNAL along with TIF_SIGPENDING
i2c: designware: Fix the functionality flags of the slave-only interface
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
commit 99f4570cfb upstream.
clkdev DEV ID information is limited to an array of 20 bytes
(MAX_DEV_ID). It is possible that the ID could be longer than
that. If so, the lookup will fail because the "real ID" will
not match the copied value.
For instance, generating a device name for the I2C Designware
module using the PCI ID can result in a name of:
i2c_designware.39424
clkdev_create() will store:
i2c_designware.3942
The stored name is one off and will not match correctly during probe.
Increase the size of the ID to allow for a longer name.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Link: https://lore.kernel.org/r/20240223202556.2194021-1-michael.j.ruhl@intel.com
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2607133196 ]
These clkdevs were unnecessary, because systems using this driver always
look up clocks using the devicetree. And as Russell King points out[1],
since the provided device name was truncated, lookups via clkdev would
never match.
Recently, commit 8d532528ff ("clkdev: report over-sized strings when
creating clkdev entries") caused clkdev registration to fail due to the
truncation, and this now prevents the driver from probing. Fix the
driver by removing the clkdev registration.
Link: https://lore.kernel.org/linux-clk/ZkfYqj+OcAxd9O2t@shell.armlinux.org.uk/ [1]
Fixes: 30b8e27e3b ("clk: sifive: add a driver for the SiFive FU540 PRCI IP block")
Fixes: 8d532528ff ("clkdev: report over-sized strings when creating clkdev entries")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/linux-clk/7eda7621-0dde-4153-89e4-172e4c095d01@roeck-us.net/
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20240528001432.1200403-1-samuel.holland@sifive.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zdH0
-----END PGP SIGNATURE-----
Merge tag 'v6.6.34' into lf-6.6.y
This is the 6.6.34 stable release
* tag 'v6.6.34': (2530 commits)
Linux 6.6.34
smp: Provide 'setup_max_cpus' definition on UP too
selftests: net: more strict check in net_helper
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
drivers/net/ethernet/freescale/fec_ptp.c
drivers/pmdomain/imx/imx8mp-blk-ctrl.c
drivers/usb/dwc3/host.c
tools/perf/util/pmu.c
commit 3c5b3e17b8 upstream.
The clk_alpha_pll_stromer_set_rate() function writes inproper
values into the ALPHA_VAL{,_U} registers which results in wrong
clock rates when the alpha value is used.
The broken behaviour can be seen on IPQ5018 for example, when
dynamic scaling sets the CPU frequency to 800000 KHz. In this
case the CPU cores are running only at 792031 KHz:
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
800000
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
792031
This happens because the function ignores the fact that the alpha
value calculated by the alpha_pll_round_rate() function is only
32 bits wide which must be extended to 40 bits if it is used on
a hardware which supports 40 bits wide values.
Extend the clk_alpha_pll_stromer_set_rate() function to convert
the alpha value to 40 bits before wrinting that into the registers
in order to ensure that the hardware really uses the requested rate.
After the change the CPU frequency is correct:
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
800000
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
800000
Cc: stable@vger.kernel.org
Fixes: e47a4f55f2 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240328-alpha-pll-fix-stromer-set-rate-v3-1-1b79714c78bc@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dc445c190 upstream.
Commit f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with
__counted_by") annotated the hws member of 'struct clk_hw_onecell_data'
with __counted_by, which informs the bounds sanitizer about the number
of elements in hws, so that it can warn when hws is accessed out of
bounds. As noted in that change, the __counted_by member must be
initialized with the number of elements before the first array access
happens, otherwise there will be a warning from each access prior to the
initialization because the number of elements is zero. This occurs in
raspberrypi_discover_clocks() due to ->num being assigned after ->hws
has been accessed:
UBSAN: array-index-out-of-bounds in drivers/clk/bcm/clk-raspberrypi.c:374:4
index 3 is out of range for type 'struct clk_hw *[] __counted_by(num)' (aka 'struct clk_hw *[]')
Move the ->num initialization to before the first access of ->hws, which
clears up the warning.
Cc: stable@vger.kernel.org
Fixes: f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240425-cbl-bcm-assign-counted-by-val-before-access-v1-2-e2db3b82d5ef@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9368cdf90f upstream.
Commit f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with
__counted_by") annotated the hws member of 'struct clk_hw_onecell_data'
with __counted_by, which informs the bounds sanitizer about the number
of elements in hws, so that it can warn when hws is accessed out of
bounds. As noted in that change, the __counted_by member must be
initialized with the number of elements before the first array access
happens, otherwise there will be a warning from each access prior to the
initialization because the number of elements is zero. This occurs in
clk_dvp_probe() due to ->num being assigned after ->hws has been
accessed:
UBSAN: array-index-out-of-bounds in drivers/clk/bcm/clk-bcm2711-dvp.c:59:2
index 0 is out of range for type 'struct clk_hw *[] __counted_by(num)' (aka 'struct clk_hw *[]')
Move the ->num initialization to before the first access of ->hws, which
clears up the warning.
Cc: stable@vger.kernel.org
Fixes: f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240425-cbl-bcm-assign-counted-by-val-before-access-v1-1-e2db3b82d5ef@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e90b5139da ]
On SM8550 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 90114ca114 ("clk: qcom: add SM8550 DISPCC driver")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-3-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1113501cfb ]
On SM6350 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 837519775f ("clk: qcom: Add display clock controller driver for SM6350")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-2-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e801038a02 ]
On SM8450 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 16fb89f92e ("clk: qcom: Add support for Display Clock Controller on SM8450")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-1-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b23118bdb ]
According to Figure 52A.1 ("RS-CANFD Module Block Diagram (in classical
CAN mode)") in the R-Car V3U Series User’s Manual Rev. 0.5, the parent
clock for the CANFD peripheral module clock is the S3D2 clock.
Fixes: 9b621b6adf ("clk: renesas: r8a779a0: Add CANFD module clock")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/aef9300f44c9141b1465343f91c5cc7303249b6e.1713279523.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f2bc4acbb ]
The offset of the CONFIG_CTL_U register defined for the Stromer
PLL is wrong. It is not aligned on a 4 bytes boundary which might
causes errors in regmap operations.
Maybe the intention behind of using the 0xff value was to indicate
that the register is not implemented in the PLL, but this is not
verified anywhere in the code. Moreover, this value is not used
even in other register offset arrays despite that those PLLs also
have unimplemented registers.
Additionally, on the Stromer PLLs the current code only touches
the CONFIG_CTL_U register if the result of pll_has_64bit_config()
is true which condition is not affected by the change.
Due to the reasons above, simply remove the CONFIG_CTL_U entry
from the Stromer specific array.
Fixes: e47a4f55f2 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240311-alpha-pll-stromer-cleanup-v1-1-f7c0c5607cca@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1758c68c81 ]
According to 9FGV0241, 9FGV0441 & 9FGV0841 datasheets, the default
value for the clock amplitude is 0.8V, while the driver assumes 0.7V.
Additionally, define constants for default values for both clock
amplitude and spread spectrum and use them.
Fixes: 892e0ddea1 ("clk: rs9: Add Renesas 9-series PCIe clock generator driver")
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240415140348.2887619-1-catalin.popescu@leica-geosystems.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c0c087772 ]
To have a working display through DPI, a workaround has been
implemented downstream to add "mm_dpi0_dpi0" and "dpi0_sel" to
the DPI node. Shortly, that add an extra clock.
It seems consistent to have the "dpi0_sel" as parent.
Additionnaly, "vpll_dpix" isn't used/managed.
Then, set the "mm_dpi0_dpi0" parent clock to "dpi0_sel".
The new clock tree is:
clk26m
lvdspll
lvdspll_X (2, 4, 8, 16)
dpi0_sel
mm_dpi0_dpi0
Fixes: d46adccb79 ("clk: mediatek: add driver for MT8365 SoC")
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20231023-display-support-v3-12-53388f3ed34b@baylibre.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb7b3c8e71 ]
Support for fhctl clocks in apmixedsys was introduced at a later point
and to this moment only one mt6795 based platform has a fhctl DT node
present. Therefore the fhctl support in apmixedsys should be seen as
optional and not cause an error when it is missing.
Change the message's log level to warning. The warning level is chosen
so that it will still alert the fact that fhctl support might be
unintentionally missing, but without implying that this is necessarily
an issue.
Even if the FHCTL DT nodes are added to all current platforms moving
forward, since those changes won't be backported, this ensures stable
kernel releases won't have live with this error.
Fixes: d7964de8a8 ("clk: mediatek: Add new clock driver to handle FHCTL hardware")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240308-mtk-fhctl-no-node-error-v1-1-51e446eb149a@collabora.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04ee3a0b44 ]
All PLL id values of CMU_TOP were incorrectly set to FOUT_SHARED0_PLL.
It modified to the correct PLL clock id value.
Fixes: 6587c62f69 ("clk: samsung: add top clock support for Exynos Auto v9 SoC")
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240328091000.17660-1-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 69f16d9b78 upstream.
When the Allwinner A64's TCON0 searches the ideal rate for the connected
panel, it may happen that it requests a rate from its parent PLL-MIPI
which PLL-MIPI does not support.
This happens for example on the Olimex TERES-I laptop where TCON0
requests PLL-MIPI to change to a rate of several GHz which causes the
panel to stay blank. It also happens on the pinephone where a rate of
less than 500 MHz is requested which causes instabilities on some
phones.
Set the minimum and maximum rate of Allwinner A64's PLL-MIPI according
to the Allwinner User Manual.
Fixes: ca1170b699 ("clk: sunxi-ng: a64: force select PLL_MIPI in TCON0 mux")
Reported-by: Diego Roversi <diegor@tiscali.it>
Closes: https://groups.google.com/g/linux-sunxi/c/Rh-Uqqa66bw
Tested-by: Diego Roversi <diegor@tiscali.it>
Cc: stable@vger.kernel.org
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240310-pinephone-pll-fixes-v4-2-46fc80c83637@oltmanns.dev
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b914ec33b3 upstream.
The Allwinner SoC's typically have an upper and lower limit for their
clocks' rates. Up until now, support for that has been implemented
separately for each clock type.
Implement that functionality in the sunxi-ng's common part making use of
the CCF rate liming capabilities, so that it is available for all clock
types.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Cc: stable@vger.kernel.org
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20240310-pinephone-pll-fixes-v4-1-46fc80c83637@oltmanns.dev
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
