[ Upstream commit 5062d9c0cb ]
Negate the values reported for the accelerometer z-axis in order to
match Documentation/devicetree/bindings/iio/mount-matrix.txt.
Fixes: 14a213dcb0 ("ARM: dts: n900: use iio driver for accelerometer")
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Reviewed-By: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20240722113137.3240847-1-absicsz@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8512fbb64b upstream.
On the imx6dl-yapp4 revision based boards, the RGB LED is not driven
directly by the LP5562 driver but through FET transistors. Hence the LED
current is not determined by the driver but by the LED series resistors.
On the imx6dl-yapp43 revision based boards, we removed the FET transistors
to drive the LED directly from the LP5562 but forgot to tune the output
current to match the previous HW design.
Set the LED current on imx6dl-yapp43 based boards to the same values
measured on the imx6dl-yapp4 boards and limit the maximum current to 20mA.
Fixes: 7da4734751 ("ARM: dts: imx6dl-yapp43: Add support for new HW revision of the IOTA board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74e1c956a6 ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b972d6b3b4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edfea889a0 ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae1 ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98c ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0df3c7d7a7 ]
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98c ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4306c04741 ]
STM32MP15xx RM0436 Rev 6 section 46.3 System timer generator (STGEN) states
"
Arm recommends that the system counter is in an always-on power domain.
This is not supported in the current implementation, therefore STGEN should
be saved and restored before Standby mode entry, and restored at Standby
exit by secure software.
...
"
Instead of piling up workarounds in the firmware which is difficult to
update, add "arm,no-tick-in-suspend" DT property into the timer node to
indicate the timer is stopped in suspend, and let the kernel fix the
timer up.
Fixes: 8471a20253 ("ARM: dts: stm32: add stm32mp157c initial support")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tthe original focaltech touchscreen on the imx7ulp evk board is EOL,
the new version board drop this touchscreen, use another touchscreen
chip. Disable this node in imx7ulp to avoid be compatible with other
FTS touchscreen driver.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
[ Upstream commit cca46f811d ]
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3066a.dtsi'.
Fixes: fadc780624 ("ARM: dts: rockchip: add rk3066 hdmi nodes")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/8b229dcc-94e4-4bbc-9efc-9d5ddd694532@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zdH0
-----END PGP SIGNATURE-----
Merge tag 'v6.6.34' into lf-6.6.y
This is the 6.6.34 stable release
* tag 'v6.6.34': (2530 commits)
Linux 6.6.34
smp: Provide 'setup_max_cpus' definition on UP too
selftests: net: more strict check in net_helper
...
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Conflicts:
arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
drivers/net/ethernet/freescale/fec_ptp.c
drivers/pmdomain/imx/imx8mp-blk-ctrl.c
drivers/usb/dwc3/host.c
tools/perf/util/pmu.c
commit 88208d3cd7 upstream.
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-origen.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: bd08f6277e ("ARM: dts: Add keypad entries to Exynos4412 based Origen")
Link: https://lore.kernel.org/r/20240312183105.715735-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ac4c1d794 upstream.
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-smdk4412.dtb: keypad@100a0000: 'key-A', 'key-B', 'key-C', 'key-D', 'key-E', 'linux,keypad-no-autorepeat' do not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: c9b92dd701 ("ARM: dts: Add keypad entries to SMDK4412")
Link: https://lore.kernel.org/r/20240312183105.715735-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87d8e522d6 upstream.
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4210-smdkv310.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: 0561ceabd0 ("ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN")
Link: https://lore.kernel.org/r/20240312183105.715735-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e027b71762 ]
By checking the pmic node with microchip,mcp16502.yaml#
'regulator-suspend-voltage' does not match any of the
regexes 'pinctrl-[0-9]+' from schema microchip,mcp16502.yaml#
which inherits regulator.yaml#. So replace regulator-suspend-voltage
with regulator-suspend-microvolt to avoid the inconsitency.
Fixes: 85b1304b9d ("ARM: dts: at91: sama7g5ek: set regulator voltages for standby state")
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240404123824.19182-2-andrei.simion@microchip.com
[claudiu.beznea: added a dot before starting the last sentence in commit
description]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 585e4dc071 ]
Fix rk3288 hdmi ports node so that it matches the
rockchip,dw-hdmi.yaml binding with some reordering
to align with the (new) documentation about
property ordering.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/cc3a9b4f-076d-4660-b464-615003b6a066@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 5f55da4cc3.
NXP downstream code base still use LCDIF fbdev driver
drivers/video/fbdev/mxsfb.c
The compatible string "fsl,imx6sx-lcdif" is only for DRM version.
Remove this patch and keep compatible string to "fsl,imx28-lcdif"
for LCDIF fbdev version.
The fsl,sdio-async-interrupt-enabled property is now dropped by
sdhci-esdhc-imx driver, so needs to remove this property for SDIO wifi
dts node accordingly.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
[ Upstream commit 79978bff2e ]
We identified that the PHYs actually do not work since commit 7da7b84fee
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 023bd910d3 ]
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497f ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3baa4c5143 ]
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 724c4bf0e4 ]
The qfprom actually is bigger than 0x1000, so adjust the reg.
Note that the non-ECC-corrected qfprom can be found at 0xfc4b8000
(-0x4000). The current reg points to the ECC-corrected qfprom block
which should have equivalent values at all offsets compared to the
non-corrected version.
[luca@z3ntu.xyz: extract to standalone patch and adjust for review
comments]
Fixes: c59ffb5193 ("arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240210-msm8974-qfprom-v3-1-26c424160334@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 090c409457 ]
External clocks should be defined as zero-Hz clocks in the SoC .dtsi,
and overridden in the board .dts when present.
Correct the clock rate of extal1 from 25 to 26 MHz, to match the crystal
oscillator present on the APE6-EVM board.
Fixes: a76809a329 ("ARM: shmobile: r8a73a4: Common clock framework DT description")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/1692bc8cd465d62168cbf110522ad62a7af3f606.1705315614.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f02b0f0dc2 ]
The dtc interrupt_map warning is off because its dependency,
interrupt_provider, is off by default. Fix all the warnings so it can be
enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-4-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96fd598e9c ]
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-2-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f98643d8da ]
The binding doesn't define interrupts and adding such a definition was
refused because it's unclear how they should ever be used and the
relevant registers are outside the PWM range. So drop them fixing
several dtbs_check warnings like:
arch/arm/boot/dts/rockchip/rv1108-elgin-r1.dtb: pwm@10280030: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/pwm/pwm-rockchip.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240129113205.2453029-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858d83ca4b ]
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aa1a82fb ]
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc35e253d0 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11ab7ad6f7 ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0b929f587 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c248e53597 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fb7b2a2f0 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1d7cc478 ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c711b882 ]
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f55da4cc3 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d4ac04fa7 ]
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07e6a553c2 ]
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@fa600000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@fa600000: missing or empty reg/ranges property
Subtract 0xfa600000 from all its children nodes. No functional impact
expected.
Link: https://lore.kernel.org/r/20230722121719.150094-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
